10MHz pulse generator with delay
●
0.1Hz to 10MHz frequency range
●
50ns minimum pulse width; fully variable pulse delay
●
Squarewave, double pulse and delayed pulse modes
●
Free-run, gated and triggered modes
●
50
W
output, variable 0.1V to 10V; TTL and sync outputs
AIM & THURLBY THANDAR INSTRUMENTS
TGP110
Designed and built in Europe by:
82100-0066 Iss. 1A
TGP110 10MHz pulse generator with delay
An essential instrument
The generation of pulses for the stimulus and control of elec-
tronic systems is beyond the capability of all but the most so-
phisticated of function generators.
The architecture of a dedicated pulse generator enables it to
generate pulses of a set width regardless of the repetition rate
offering duty cycles which can extend down to 1 in 100 million.
In addition to continuous operation, single or multiple pulses
can be generated in response to trigger or gating signals with
precisely defined timing relationships.
A dedicated pulse-waveform output amplifier provides flat top
pulses with fast rise and fall times at variable amplitude.
Variable delay
The TGP110 offers selectable delay between the sync output
and pulse output. In triggered mode this also sets the delay be-
tween a trigger signal and the start of the pulse.
Wide pulse range
The TGP110 can generate pulse widths in the range 50ns to 5s.
There are eight overlapping decade ranges with vernier control
within each range.
The period range is 100ns to 10s, equivalent to a repetition rate
range of 10MHz to 0.1Hz. Delay is independently adjustable
over the same range as pulse width.
A complement switch inverts the mark-space polarity.
Squarewave and double pulse
In square mode, squarewaves are generated at a frequency set
by the period controls alone. This provides a convenient means
of generating variable period edges where the pulse width is
unimportant, for example.
In double pulse mode, a second pulse is generated within every
period at a set delay after the start of the first pulse. The delay is
independently adjustable.
PERIOD, PULSE WIDTH, DELAY
Each parameter is variable within 8 overlapping decade ranges with a
vernier providing continuously variable control within each range.
PERIOD
Range: 100nsec to 10sec (10MHz to 0·1Hz).
Jitter: <0.1%.
PULSE WIDTH
Range: 50nsec to 5sec
Jitter: <0.1%.
DELAY
Range: 50nsec to 5sec
TRIGGER, GATE
RUN
Normal operational mode in which pulses are generated continuously at
0.1Hz to 10MHz.
TRIGGERED
DC to 10MHz pulse train in synchronism with external trigger pulses;
pulse width determined by pulse width controls. Trigger can be gener-
ated manually from front panel button.
GATED
0·1Hz to 10MHz pulse train, parameters set by period and pulse width
controls, starts synchronously with leading edge of gate input. Last pulse
is completed at the end of gating period. Gating signal can be generated
manually from front panel button.
PULSE MODES
NORMAL PULSE
One pulse is generated each period. The delay setting is ignored.
SQUAREWAVE
0·1Hz to 10MHz squarewave, frequency set by the period controls.
Pulse width and delay settings ignored.
Mark : Space ratio: 1:1 ±10%.
DOUBLE PULSE
A second pulse is generated after a delay set by the delay controls; the
delay is related to the leading edge of the first pulse.
DELAYED PULSE
A pulse is generated after a delay set by the delay controls; the delay is
related to rising edge of the trigger signal.
INPUTS
GATE/TRIG INPUT
Frequency range: DC - 10MHz
Signal range: TTL threshold; max. input ±10V.
Min. pulse width: >30nsec.
Input Impedance: Typically 10kW.
OUTPUTS
50WOUTPUT
Amplitude: Two switch selectable ranges of 0·1V - 1·0V and
1V - 10V from 50W. (50mV to 500mV and 500mV to
5V into 50W). Adjustable within ranges by a single
turn vernier.
Rise/Fall Times: Typically 10nsec into 50Wload. Maximum 15ns.
Aberrations: Typically <5% for output set at >20% of range maxi-
mum, into 50W.
AUX OUTPUT
Duplicates 50Woutput but at a fixed CMOS/TTL level.
SYNC OUTPUT
Amplitude: A positive going pulse at CMOS/TTL level.
Timing: Leading edge starts >20nsec before the TTL/50W
output transition.
Duration: Typically 30nsec.
COMPLEMENT SWITCH
Inverts the AUX and 50Woutputs.
GENERAL
Power: 230V or 115V AC nominal 50/60Hz, adjustable inter-
nally; operating range ±14% of nominal; 20VA max.
Size: 140 x 220 x 230mm (HxWxD)
Weight: 1.6kg (3.5lb)
Operating Range: + 5°C to 40°C, 20-80% RH.
Storage Range: - 40°C to 70°C
Safety: Complies with EN61010-1.
EMC: Complies with EN55081-1 and EN50082-1.
Thurlby Thandar Instruments Ltd. operates a policy of continuous development and reserves
the right to alter specifications without prior notice.
Thurlby Thandar Instruments Ltd.
Glebe Road, Huntingdon. Cambs. PE29 7DR England
Tel: +44 (0)1480 412451 Fax: +44 (0) 1480 450409
Email: info@aimtti.com Web: www.aimtti.com
CYAN MAGENTA YELLOW BLACK CYAN MAGENTA YELLOW BLACK
10MHz pulse generator with delay
●
0.1Hz to 10MHz frequency range
●
50ns minimum pulse width; fully variable pulse delay
●
Squarewave, double pulse and delayed pulse modes
●
Free-run, gated and triggered modes
●
50
W
output, variable 0.1V to 10V; TTL and sync outputs
AIM & THURLBY THANDAR INSTRUMENTS
TGP110
Designed and built in Europe by:
82100-0066 Iss. 1A
TGP110 10MHz pulse generator with delay
An essential instrument
The generation of pulses for the stimulus and control of elec-
tronic systems is beyond the capability of all but the most so-
phisticated of function generators.
The architecture of a dedicated pulse generator enables it to
generate pulses of a set width regardless of the repetition rate
offering duty cycles which can extend down to 1 in 100 million.
In addition to continuous operation, single or multiple pulses
can be generated in response to trigger or gating signals with
precisely defined timing relationships.
A dedicated pulse-waveform output amplifier provides flat top
pulses with fast rise and fall times at variable amplitude.
Variable delay
The TGP110 offers selectable delay between the sync output
and pulse output. In triggered mode this also sets the delay be-
tween a trigger signal and the start of the pulse.
Wide pulse range
The TGP110 can generate pulse widths in the range 50ns to 5s.
There are eight overlapping decade ranges with vernier control
within each range.
The period range is 100ns to 10s, equivalent to a repetition rate
range of 10MHz to 0.1Hz. Delay is independently adjustable
over the same range as pulse width.
A complement switch inverts the mark-space polarity.
Squarewave and double pulse
In square mode, squarewaves are generated at a frequency set
by the period controls alone. This provides a convenient means
of generating variable period edges where the pulse width is
unimportant, for example.
In double pulse mode, a second pulse is generated within every
period at a set delay after the start of the first pulse. The delay is
independently adjustable.
PERIOD, PULSE WIDTH, DELAY
Each parameter is variable within 8 overlapping decade ranges with a
vernier providing continuously variable control within each range.
PERIOD
Range: 100nsec to 10sec (10MHz to 0·1Hz).
Jitter: <0.1%.
PULSE WIDTH
Range: 50nsec to 5sec
Jitter: <0.1%.
DELAY
Range: 50nsec to 5sec
TRIGGER, GATE
RUN
Normal operational mode in which pulses are generated continuously at
0.1Hz to 10MHz.
TRIGGERED
DC to 10MHz pulse train in synchronism with external trigger pulses;
pulse width determined by pulse width controls. Trigger can be gener-
ated manually from front panel button.
GATED
0·1Hz to 10MHz pulse train, parameters set by period and pulse width
controls, starts synchronously with leading edge of gate input. Last pulse
is completed at the end of gating period. Gating signal can be generated
manually from front panel button.
PULSE MODES
NORMAL PULSE
One pulse is generated each period. The delay setting is ignored.
SQUAREWAVE
0·1Hz to 10MHz squarewave, frequency set by the period controls.
Pulse width and delay settings ignored.
Mark : Space ratio: 1:1 ±10%.
DOUBLE PULSE
A second pulse is generated after a delay set by the delay controls; the
delay is related to the leading edge of the first pulse.
DELAYED PULSE
A pulse is generated after a delay set by the delay controls; the delay is
related to rising edge of the trigger signal.
INPUTS
GATE/TRIG INPUT
Frequency range: DC - 10MHz
Signal range: TTL threshold; max. input ±10V.
Min. pulse width: >30nsec.
Input Impedance: Typically 10kW.
OUTPUTS
50WOUTPUT
Amplitude: Two switch selectable ranges of 0·1V - 1·0V and
1V - 10V from 50W. (50mV to 500mV and 500mV to
5V into 50W). Adjustable within ranges by a single
turn vernier.
Rise/Fall Times: Typically 10nsec into 50Wload. Maximum 15ns.
Aberrations: Typically <5% for output set at >20% of range maxi-
mum, into 50W.
AUX OUTPUT
Duplicates 50Woutput but at a fixed CMOS/TTL level.
SYNC OUTPUT
Amplitude: A positive going pulse at CMOS/TTL level.
Timing: Leading edge starts >20nsec before the TTL/50W
output transition.
Duration: Typically 30nsec.
COMPLEMENT SWITCH
Inverts the AUX and 50Woutputs.
GENERAL
Power: 230V or 115V AC nominal 50/60Hz, adjustable inter-
nally; operating range ±14% of nominal; 20VA max.
Size: 140 x 220 x 230mm (HxWxD)
Weight: 1.6kg (3.5lb)
Operating Range: + 5°C to 40°C, 20-80% RH.
Storage Range: - 40°C to 70°C
Safety: Complies with EN61010-1.
EMC: Complies with EN55081-1 and EN50082-1.
Thurlby Thandar Instruments Ltd. operates a policy of continuous development and reserves
the right to alter specifications without prior notice.
Thurlby Thandar Instruments Ltd.
Glebe Road, Huntingdon. Cambs. PE29 7DR England
Tel: +44 (0)1480 412451 Fax: +44 (0) 1480 450409
Email: info@aimtti.com Web: www.aimtti.com
CYAN MAGENTA YELLOW BLACK CYAN MAGENTA YELLOW BLACK
Thurlby Thandar Instruments Ltd.
Glebe Road, Huntingdon, Cambridgeshire PE29 7DR England (United Kingdom)
Tel: +44 (0)1480 412451 Fax: +44 (0)1480 450409
Email: info@aimtti.com Web: www.aimtti.com
Designed and built in Europe by:
Company name and product brands
Thurlby Thandar Instruments Ltd. (TTi) is one of Europe’s leading
manufacturers of test and measurement instruments.
Products have been sold under two brand names:
TTi and Aim.
In the future, however, the full product range will be branded Aim-TTi.
This changeover will be gradual and many products will continue to carry
the TTi or Aim brands for some time to come.
Web Addresses (URLs)
The preferred URL for obtaining information concerning Aim-TTi products
is:
www.aimtti.com (international customers)
Customers in the UK should use the URL:
www.aimtti.co.uk
Customers in the USA should use the URL:
www.aimtti.us
Note that previous URLs such as www.tti-test.com will continue to operate
for the time being.
Product Summary
Laboratory Power Supplies
Bench and system power supplies from 30 watts up to
1200 watts using linear, mixed-mode and PowerFlex
regulation technologies.
Waveform Generators
Analog and digital (DDS) function generators, true
arbitrary generators, arbitrary/function generators and
pulse generators.
Precision Measurement Instruments
Benchtop DMMs, frequency counters, component
measurement instruments (LCR), electronic dc loads,
current probes.
RF and EMC Test Equipment
Spectrum analyzers, signal generators, frequency counters,
power meters, emc measurement instruments.
