SN74LS365A SN74LS367A SN74LS368A 3-State Hex Buffers These devices are high speed hex buffers with 3-state outputs. They are organized as single 6-bit or 2-bit / 4-bit, with inverting or non-inverting data (D) paths. The outputs are designed to drive 15 TTL Unit Loads or 60 Low Power Schottky loads when the Enable (E) is LOW. When the Output Enable (E) is HIGH, the outputs are forced to a high impedance "off" state. If the outputs of the 3-state devices are tied together, all but one device must be in the high impedance state to avoid high currents that would exceed the maximum ratings. Designers should ensure that Output Enable signals to 3-state devices whose outputs are tied together are designed so there is no overlap. http://onsemi.com LOW POWER SCHOTTKY GUARANTEED OPERATING RANGES Symbol VCC Parameter Supply Voltage Min Typ Max Unit 4.75 5.0 5.25 V 0 25 70 C TA Operating Ambient Temperature Range IOH Output Current - High - 2.6 mA IOL Output Current - Low 24 mA 16 1 PLASTIC N SUFFIX CASE 648 16 1 SOIC D SUFFIX CASE 751B ORDERING INFORMATION Semiconductor Components Industries, LLC, 1999 December, 1999 - Rev. 6 1 Device Package Shipping SN74LS365AN 16 Pin DIP 2000 Units/Box SN74LS365AD 16 Pin 2500/Tape & Reel SN74LS367AN 16 Pin DIP 2000 Units/Box SN74LS367AD 16 Pin 2500/Tape & Reel SN74LS368AN 16 Pin DIP 2000 Units/Box SN74LS368AD 16 Pin 2500/Tape & Reel Publication Order Number: SN74LS365A/D SN74LS365A SN74LS367A SN74LS368A SN74LS365A HEX 3-STATE BUFFER WITH COMMON 2-INPUT NOR ENABLE VCC E2 16 15 14 13 12 11 10 9 1 E1 2 3 4 5 6 7 8 GND TRUTH TABLE INPUTS OUTPUT E1 E2 D L L H X L L X H L H X X L H (Z) (Z) SN74LS367A HEX 3-STATE BUFFER SEPARATE 2-BIT AND 4-BIT SECTIONS SN74LS368A HEX 3-STATE INVERTER BUFFER SEPARATE 2-BIT AND 4-BIT SECTIONS VCC E VCC E 16 15 14 13 12 11 10 9 16 15 14 13 12 11 10 9 1 E 2 3 4 5 6 7 8 GND 1 E 2 3 4 5 6 7 8 GND TRUTH TABLE INPUTS E D L L H L H X TRUTH TABLE INPUTS OUTPUT L H (Z) http://onsemi.com 2 E D L L H L H X OUTPUT H L (Z) SN74LS365A SN74LS367A SN74LS368A DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol Parameter VIH Input HIGH Voltage VIL Input LOW Voltage VIK Input Clamp Diode Voltage VOH Output HIGH Voltage VOL O Output LOW Voltage Min Typ Max Unit 2.0 0.8 - 0.65 2.4 - 1.5 3.1 Test Conditions V Guaranteed Input HIGH Voltage for All Inputs V Guaranteed Input LOW Voltage for All Inputs V VCC = MIN, IIN = - 18 mA V VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table 0.25 0.4 V IOL = 12 mA 0.35 0.5 V IOL = 24 mA VCC = VCC MIN, VIN = VIL or VIH per Truth Table IOZH Output Off Current HIGH 20 A VCC = MAX, VOUT = 2.7 V IOZL Output Off Current LOW - 20 A VCC = MAX, VOUT = 0.4 V 20 IIH Input HIGH Current A VCC = MAX, VIN = 2.7 V 0.1 mA VCC = MAX, VIN = 7.0 V - 0.4 mA VCC = MAX, VIN = 0.4 V - 20 A VCC = MAX, VIN = 0.5 V Either E Input at 2.0 V - 0.4 mA VCC = MAX, VIN = 0.4 V Both E Inputs at 0.4 V - 225 mA VCC = MAX 24 mA VCC = MAX Input LOW Current E Inputs IIL D Inputs IOS ICC Short Circuit Current (Note 1) - 40 Power Supply Current LS365A, 367A LS368A 21 Note 1: Not more than one output should be shorted at a time, nor for more than 1 second. AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V) Limits LS365A / LS367A Symbol Parameter LS366A / LS368A Typ Max Unit 16 22 7.0 12 15 18 ns 35 40 18 28 35 45 ns 32 35 ns Typ Max Propagation Delay 10 9.0 tPZH tPZL Output Enable Time 19 24 tPHZ tPLZ Output Disable Time tPLH tPHL Min Min 30 35 http://onsemi.com 3 Test Conditions CL = 45 pF, RL = 667 CL = 5.0 pF SN74LS365A SN74LS367A SN74LS368A PACKAGE DIMENSIONS 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. N SUFFIX PLASTIC PACKAGE CASE 648-08 ISSUE R -A- B F C DIM A B C D F G H J K L M S L S SEATING PLANE -T- K H G D M J 16 PL 0.25 (0.010) T A M D SUFFIX PLASTIC SOIC PACKAGE CASE 751B-05 ISSUE J -A- 16 9 -B- 1 M P 0.25 (0.010) M B S G R K F X 45 _ C -T- SEATING PLANE J M D 16 PL 0.25 (0.010) M T B S A S MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 8 PL 8 INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION North America Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong 800-4422-3781 Email: ONlit-asia@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (M-F 2:30pm to 5:00pm Munich Time) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (M-F 2:30pm to 5:00pm Toulouse Time) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (M-F 1:30pm to 5:00pm UK Time) Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 Phone: 81-3-5487-8345 Email: r14153@onsemi.com Fax Response Line: 303-675-2167 800-344-3810 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. http://onsemi.com 4 SN74LS365A/D