DS15004 Rev. E-2 1 of 2 RS2A/A - RS2M/A
RS2A/A - RS2M/A
1.5A SURFACE MOUNT FAST RECOVERY RECTIFIER
Features
AA, BA, DA, GA, JA, KA, MA Suffix Designates SMA Package
A, B, D, G, J, K Suffix Designates SMB Package
SMA SMB
Dim Min Max Min Max
A2.29 2.92 3.30 3.94
B4.00 4.60 4.06 4.57
C1.27 1.63 1.96 2.21
D0.15 0.31 0.15 0.31
E4.80 5.59 5.00 5.59
G0.10 0.20 0.10 0.20
H0.76 1.52 0.76 1.52
J2.01 2.62 2.00 2.62
All Dimensions in mm
A
B
C
D
G
H
E
J
Glass Passivated Die Construction
Fast Recovery Time For High Efficiency
Low Forward Voltage Drop and High Current
Capability
Surge Overload Rating to 50A Peak
Ideally Suited for Automated Assembly
Plastic Material: UL Flammability
Classification Rating 94V-0
Mechanical Data
Case: Molded Plastic
Terminals: Solder Plated Terminal -
Solderable per MIL-STD-202, Method 208
Polarity: Cathode Band or Cathode Notch
SMA Weight: 0.065 grams (approx.)
SMB Weight: 0.09 grams (approx.)
Mounting Position: Any
Marking: Type Number
Maximum Ratings and Electrical Characteristics TA= 25C unless otherwise specified
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
Characteristic Symbol RS2
A/AA
RS2
B/BA
RS2
D/DA
RS2
G/GA
RS2
J/JA
RS2
K/KA
RS2
M/MA Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
VRRM
VRWM
VR
50 100 200 400 600 800 1000 V
RMS Reverse Voltage VR(RMS) 35 70 140 280 420 560 700 V
Average Rectified Output Current @ TT= 120CIO1.5 A
Non-Repetitive Peak Forward Surge Current
8.3ms Single half sine-wave Superimposed on Rated Load
(JEDEC Method)
IFSM 50 A
Forward Voltage @ IF= 1.5A VFM 1.3 V
Peak Reverse Current @ TA= 25C
at Rated DC Blocking Voltage @ TA= 125CIRM 5.0
200 A
Reverse Recovery Time (Note 3) trr 150 250 500 ns
Typical Junction Capacitance (Note 2) Cj30 pF
Typical Thermal Resistance, Junction to Terminal (Note 1) RJT 20 K/W
Operating and Storage Temperature Range Tj, TSTG -65 to +150 C
Notes: 1. Thermal Resistance: Junction to terminal, unit mounted on PC board with 5.0 mm2(0.013 mm thick) copper pads as heat sink.
2. Measured at 1.0MHz and applied reverse voltage of 4.0V DC.
3. Reverse Recovery Test Conditions: IF= 0.5A, IR= 1.0A, Irr = 0.25A. See Figure 5.
DS15004 Rev. E-2 2 of 2 RS2A/A - RS2M/A
0
0.5
1.0
1
.5
25 50 75 100 125 150 175
I , AVERAGE RECTIFIED CURRENT (A)
O
T , TERMINAL TEMPERATURE (°C)
Fi
g
. 1 Forward Current Deratin
g
Curve
T
0.01
0.1
1.0
10
0 0.4 0.8 1.2 1.6
T = 25°C
j
I Pulse Width: 300 µs
F
I INSTANTANEOUS FORWARD CURRENT (A)
F,
V , INSTANTANEOUS FORWARD VOLTAGE (V)
Fi
g
.2 T
y
pical Forward Characteristics
F
0
10
20
30
1 10 100
I , PEAK FORWARD SURGE CURRENT (A
)
FSM
NUMBER OF CYCLES AT 60 Hz
Fi
g
. 3 Forward Sur
g
e Current Deratin
g
Curve
Single Half-Sine-Wave
(JEDEC Method)
T = 150°C
j
40
50
50V DC
Approx
50 NI (Non-inductive)Ω10 NIΩ
1.0
NI
ΩOscilloscope
(Note 1)
Pulse
Generator
(Note 2)
Device
Under
Test
trr
Set time base for 50/100 ns/cm
+0.5A
0A
-0.25A
-1.0A
Notes:
1. Rise Time = 7.0ns max. Input Impedance = 1.0M , 22pF.
2. Rise Time = 10ns max. Input Impedance = 50 .
Ω
Ω
Fi
g
. 5 Reverse Recover
y
Time Characteristic and Test Circuit
(+)
(+)
(-)
(-)
0.1
1.0
10
100
1000
0 20 40 60 80 100 120 140
I , INSTANTANEOUS REVERSE CURRENT (µA
)
R
PERCENT OF RATED PEAK REVERSE VOLTAGE (%)
Fi
g
.4, T
y
pical Reverse Characteristics
T = 125°C
j
T = 25°C
j
