BCD.00285_AA_December-3-2013 1 www.power-one.com
DATA SHEET
Instrumentation
Lighting
Industrial Applications
Test and Measurement
Robotics
Renewable Energy
Data Comm.
Applied Computing
Process Control
Wireless
ABC300 SERIES 300W AC/DC
200 W convection cooled
-20 to 50 deg C full load operation
3” x 5“ x 1.5” (76.2 x 127 x 38.1 mm)
No minimum load required
12 V fan & 5 V standby outputs
Inhibit and Power Good signals
Conducted EMI EN 55022-B, FCC Part 15 Level B
ITE Safety Agency Approvals
RoHS Compliant
FEATURES
APPLICATIONS
ABC300 Series 2 www.power-one.com
TECHNICAL DATA:
Input
PARAMETER
DESCRIPTION/CONDITION
Input voltage range
Universal Input
90 - 264 Vac
120 – 390 Vdc
Input frequency range
47-63 Hz
Input surge current
230 Vac (cold start)
65 A max.
Safety ground leakage current
230 Vac
300 μA max
Input current
120 Vac @ 200 W
230 Vac @ 200 W
3.2 A
1.65 A
Output
PARAMETER
DESCRIPTION/CONDITION
Voltage Adjustment
V1
± 3%
Transient Response
Main output 50 to 100% load change, 50 Hz,
50% duty cycle, 0.1 A / uSec, 50/60 Hz.
< 10%, recovery time < 5 mSec
Over Voltage Protection
V1
110 to 150% rated max
Over Current Protection
Rated output current
110 to 150% Typical
Short Circuit Protection
Automatic recovery
Over Temperature Protection
Automatic recovery
110° C primary heatsink
Set point tolerance
± 1%
Rise Time
<100 mSec
Ordering Information
PRODUCT FAMILY
VOLTS
(VDC)
MAX LOAD
CONVECTION (2)
MAX LOAD
300 LFM (2)
MINIMUM
LOAD (A)
RIPPLE &
NOISE (4)
CONNECTOR
TOTAL
REGULATION
ABC300-1T05G
5
28.0 A
40.0 A
0
2%
Screw Terminal
± 2.5%
ABC300-1T12G
12
15.0 A
25.0 A
0
2%
Screw Terminal
± 2.5%
ABC300-1T15G
15
12.0 A
20.0 A
0
2%
Screw Terminal
± 2.5%
ABC300-1T24G
24
7.5 A
13.54 A
0
2%
Screw Terminal
± 2.5%
ABC300-1T30G
30
6.0
10.83 A
0
2%
Screw Terminal
± 2.5%
ABC300-1T48G
48
3.75 A
6.77 A
0
2%
Screw Terminal
± 2.5%
Vfan (all models)
12
0.5 A
0.5 A
0
± 20%
V s/b (all models)
5
2.0 A
2.0 A
0
± 5%
BCD.00285_AA_December-3-2013 3 www.power-one.com
DATA SHEET
Notes:
1. Peak current rating of 120% of max, < 30 Sec with max of 10% duty cycle.
2. Combined power from main output, Vfan and Vs/b should not exceed total power rating.
3. Fan output tolerance is ± 20%. When V1 full load, Vfan needs 20 mA load to be within regulation specification. Peak
current for fan output is 1 A.
4. Ripple is 2% up to 20% load and less than 1% above 20% load. Output noise measurement is made with a 20 MHz
bandwidth using a 6” twisted pair, terminated with a 10 uF tantalum capacitor in parallel with a 0.1 uF ceramic capacitor.
5. Specifications are for nominal input voltage, 25° C and max load unless otherwise stated.
6. Class 1 models have Earthing tab J4. Class 2 models (-2 suffix) have no Earthing tab.
7. Derate power linearly to 80% from 90 Vac to 80 Vac input.
8. Power supply shipped with J3 pin 1 and 2 shorted to enable main output
9. Specifications subject to change without notice.
10. Air flow over long edge (either direction) required for air flow rating. See mechanical drawing below.
11. Warranty 2 years.
General Specifications
PARAMETER
DESCRIPTION/CONDITION
Hold Up Time
120 Vac
10 mSec
230 Vac
10 mSec
MTBF
>250 khrs
Bellcore TR-332
Switching Frequency
PFC converter 80 kHz typical
Resonant converter: Variable 35 to 250
kHz, 90 kHz typical
Isolation Voltage
Min 5900 Vdc
Input to Output
Weight
450 g (0.99 lbs)
Environmental
PARAMETER
DESCRIPTION/CONDITION
Operating Temperature
Operating
-20 to 70° C. See derating charts below.
Storage
-40 to +85° C.
Altitude
Operating 10,000 ft.
Non-operation 40,000 ft.
Conducted emissions:
EN55022, FCC part 15 Level B
Radiated Emissions
EN55022, FCC part 15 Level B
To be controlled in end system
Electromagnetic Susceptibility
EN61000-4 3
2, 3, 4, 5 level 3
Harmonic Current
EN61000-3-2, Class D
Signals
PARAMETER
DESCRIPTION/CONDITION
Power Good
TTL signal goes high after main output is within regulation, delay is 0.1 to 0.3 sec
Inhibit
To turn on power supply short J3 pin 1 to J3 pin 2 or J3 pin 7
Remote Sense
Compensates for 200 mV drop
Safety
PARAMETER
DESCRIPTION/CONDITION
EN / UL / CSA
EN60950-1+A12:2011, IEC60950-1 2nd+A1 2009, CSA-22.2 No 60950-01-07+ A1, UL60950-
1-2011
ABC300 Series 4 www.power-one.com
Figure 1 Output Power Vs. Temperature
Figure 2 Dimension Drawing (Top and Side View)
BCD.00285_AA_December-3-2013 5 www.power-one.com
DATA SHEET
Mechanical
INPUT = J1
EARTHING TAB = J4
DC OUTPUT = J2
SIGNALS & AUX POWER= J3
Pin 1: AC Line
Pin 2: Removed
Pin 3: AC Neutral
Molex: 19705-4301
2 x 6-32 inches pan head screw
Pin 1 = RTN
Pin 2 = V1
Pin 1 = Inhibit
Pin 2 = Signal Return
Pin 3 = Vfan (+12 V)
Pin 4 = - Remote Sense
Pin 5 = Vs/b (5 Vdc)
Pin 6 = + Remote Sense
Pin 7 = Signal Return
Pin 8 = Power Good
Mating Connector:
Molex: 09-50-3031
Pins: 08-50-0106
Mating Connector:
Molex: 190030001
Mating Connector:
16 AWG wire crimped to Ring
Tongue Terminal.
AMP: 8-31886-1
Mating Connector:
Molex: 22-01-2087, Pins: 08-50-0113
Copyright © 2010 Power-One Inc. All rights reserved. Words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the
trademarks and service marks of Power-One Inc. in the U.S. and other countries. All other product or service names are the property of their respective holders.
Power-One products are protected under numerous U.S. and foreign patents and pending applications, maskwork rights, and copyrights. Power-One reserves the
right to make changes to any products and services at any time without notice. Power-One assumes no responsibility or liability arising out of the application or use
of any information, product, or service described herein except as expressly agreed to in writing by Power-One Inc.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life
support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president
of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date
manufactured. Specifications are subject to change without notice.