19-0666; Rev 2; 3/09 KIT ATION EVALU E L B A AVAIL 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing The MAX16818 pulse-width modulation (PWM) LED driver controller provides high-output-current capability in a compact package with a minimum number of external components. The MAX16818 is suitable for use in synchronous and nonsynchronous step-down (buck) topologies, as well as in boost, buck-boost, SEPIC, and Cuk LED drivers. The MAX16818 is the first LED driver controller that enables Maxim's technology for fast LED current transients of up to 20A/s and 30kHz dimming frequency. This device utilizes average-current-mode control that enables optimal use of MOSFETs with optimal charge and on-resistance characteristics. This results in the minimized need for external heatsinking even when delivering up to 30A of LED current. True differential sensing enables accurate control of the LED current. A wide dimming range is easily implemented to accommodate an external PWM signal. An internal regulator enables operation over a wide input voltage range: 4.75V to 5.5V or 7V to 28V and above with a simple external biasing device. The wide switching frequency range, up to 1.5MHz, allows for the use of small inductors and capacitors. The MAX16818 features a clock output with 180 phase delay to control a second out-of-phase LED driver to reduce input and output filter capacitors size or to minimize ripple currents. The MAX16818 offers programmable hiccup, overvoltage, and overtemperature protection. The MAX16818ETI+ is rated for the extended temperature range (-40C to +85C) and the MAX16818ATI+ is rated for the automotive temperature range (-40C to +125C). This LED driver controller is available in a lead-free, 0.8mm high, 5mm x 5mm 28-pin TQFN package with exposed paddle. Features High-Current LED Driver Controller IC, Up to 30A Output Current Average-Current-Mode Control True-Differential Remote-Sense Input 4.75V to 5.5V or 7V to 28V Input Voltage Range Programmable Switching Frequency or External Synchronization from 125kHz to 1.5MHz Clock Output for 180 Out-of-Phase Operation Integrated 4A Gate Drivers Output Overvoltage and Hiccup Mode Overcurrent Protection Thermal Shutdown Thermally Enhanced 28-Pin Thin QFN Package -40C to +125C Operating Temperature Range Ordering Information PART TEMP RANGE PIN-PACKAGE MAX16818ATI+ -40C to +125C 28 TQFN-EP* MAX16818ETI+ -40C to +85C 28 TQFN-EP* +Denotes a lead(Pb)-free/RoHS-compliant package. *EP = Exposed pad. Simplified Diagram 7V TO 28V C1 Applications Front Projectors/Rear Projection TVs IN EN DH Q1 ILIM VLED L1 Portable and Pocket Projectors MAX16818 Automotive, Bus/Truck Exterior Lighting DL LCD TVs and Display Backlight Q2 C2 Q3 Automotive Emergency Lighting and Signage OVI CSP CLP PGND R1 HIGH-FREQUENCY PULSE TRAIN Pin Configuration appears at end of data sheet. NOTE: MAXIM TOPOLOGY ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX16818 General Description MAX16818 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing ABSOLUTE MAXIMUM RATINGS IN to SGND.............................................................-0.3V to +30V BST to SGND..........................................................-0.3V to +35V BST to LX..................................................................-0.3V to +6V DH to LX .......................................-0.3V to [(VBST - VLX_) + 0.3V] DL to PGND................................................-0.3V to (VDD + 0.3V) VCC to SGND............................................................-0.3V to +6V VCC, VDD to PGND ...................................................-0.3V to +6V SGND to PGND .....................................................-0.3V to +0.3V All Other Pins to SGND...............................-0.3V to (VCC + 0.3V) Continuous Power Dissipation (TA = +70C) 28-Pin TQFN (derate 34.5mW/C above +70C) .......2758mW Operating Temperature Range MAX16818ATI+..............................................-40C to +125C MAX16818ETI+................................................-40C to +85C Maximum Junction Temperature .....................................+150C Storage Temperature Range .............................-60C to +150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = 5V, VDD = VCC, TA = TJ = TMIN to TMAX, unless otherwise noted. Typical specifications are at TA = +25C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS SYSTEM SPECIFICATIONS Input Voltage Range VIN Short IN and VCC together for 5V input operation Quiescent Supply Current IQ EN = VCC or SGND, not switching 7 28 4.75 5.50 2.7 5.5 V mA LED CURRENT REGULATOR SENSE+ to SENSE- Accuracy (Note 2) Soft-Start Time No load, VIN = 4.75V to 5.5V, fSW = 500kHz 0.594 0.6 0.606 No load, VIN = 7V to 28V, fSW = 500kHz 0.594 0.6 0.606 tSS V Clock Cycles 1024 STARTUP/INTERNAL REGULATOR VCC Undervoltage Lockout UVLO VCC rising 4.1 VCC Undervoltage Hysteresis 4.3 4.5 200 VCC Output Voltage VIN = 7V to 28V, ISOURCE = 0 to 60mA 4.85 V mV 5.1 5.30 V 1.1 3.0 MOSFET DRIVERS Output Driver Impedance Output Driver Source/Sink Current Nonoverlap Time RON Low or high output, ISOURCE/SINK = 20mA IDH,IDL tNO CDH/DL = 5nF 4 A 35 ns OSCILLATOR Switching Frequency Range 125 Switching Frequency Switching Frequency Switching Frequency Switching Frequency Accuracy 2 fSW 1500 RT = 500k 121 125 129 RT = 120k 495 521 547 RT = 39.9k 1515 1620 1725 120k RT 500k -5 +5 40k RT 120k -8 +8 _______________________________________________________________________________________ kHz kHz % 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing (VCC = 5V, VDD = VCC, TA = TJ = TMIN to TMAX, unless otherwise noted. Typical specifications are at TA = +25C.) (Note 1) PARAMETER SYMBOL CONDITIONS _CLKOUT With respect to DH, fSW = 125kHz CLKOUT Output Low Level VCLKOUTL ISINK = 2mA CLKOUT Output High Level VCLKOUTH ISOURCE = 2mA CLKOUT Phase Shift SYNC Input-High Pulse Width MIN 0.4 ns 200 2.0 SYNC Input Clock Low Threshold VSYNCL ISYNC_OUT V V tSYNC VSYNC_OFF UNITS Degrees 4.5 VSYNCH SYNC Power-Off Level MAX 180 SYNC Input Clock High Threshold SYNC Pullup Current TYP VRT/SYNC = 0V V 250 0.4 V 750 A 0.4 V INDUCTOR CURRENT LIMIT Average Current-Limit Threshold VCL CSP to CSN 24.0 26.9 28.2 mV Reverse Current-Limit Threshold VCLR CSP to CSN -3.2 -2.3 -0.1 mV Cycle-by-Cycle Current Limit Cycle-by-Cycle Overload CSP to CSN VCSP to VCSN = 75mV Hiccup Divider Ratio LIM to VCM, no switching 60 260 0.547 Hiccup Reset Delay LIM Input Impedance mV LIM to SGND 0.558 ns 0.565 V/V 200 ms 55.9 k 4 k CURRENT-SENSE AMPLIFIER CSP or CSN Input Resistance Common-Mode Range Input Offset Voltage RCS VCMR(CS) VIN = 7V to 28V 0 5.5 V VOS(CS) 0.1 mV Amplifier Gain AV(CS) 34.5 V/V 3dB Bandwidth f3dB 4 MHz 550 S 50 dB CURRENT-ERROR AMPLIFIER (TRANSCONDUCTANCE AMPLIFIER) Transconductance gm Open-Loop Gain AVOL(CE) No load DIFFERENTIAL VOLTAGE AMPLIFIER FOR LED CURRENT (DIFF) Common-Mode Voltage Range VCMR(DIFF) 0 DIFF Output Voltage VCM Input Offset Voltage VOS(DIFF) -1 AV(DIFF) 0.994 Amplifier Gain 3dB Bandwidth f3dB Minimum Output-Current Drive SENSE+ to SENSE- Input VSENSE+ = VSENSE- = 0V RVS 1 3 4 VSENSE- = 0V V +1 mV 1.006 V/V 0.6 CDIFF = 20pF IOUT(DIFF) +1.0 50 V MHz mA 100 k 4 MHz 1 MHz V_IOUT AMPLIFIER Gain-Bandwidth Product VV_IOUT = 2.0V 3dB Bandwidth VV_IOUT = 2.0V Output Sink Current 30 A Output Source Current 90 A _______________________________________________________________________________________ 3 MAX16818 ELECTRICAL CHARACTERISTICS (continued) MAX16818 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing ELECTRICAL CHARACTERISTICS (continued) (VCC = 5V, VDD = VCC, TA = TJ = TMIN to TMAX, unless otherwise noted. Typical specifications are at TA = +25C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN Maximum Load Capacitance TYP MAX UNITS 50 V_IOUT Output to IOUT Transfer Function RSENSE = 1m, 100mV V_IOUT 5.5V 132.3 Offset Voltage 135 pF 137.7 mV/A 1 mV VOLTAGE-ERROR AMPLIFIER (EAOUT) Open-Loop Gain AVOLEA 70 dB Unity-Gain Bandwidth fGBW 3 MHz EAN Input Bias Current IB(EA) Error Amplifier Output Clamping Voltage VEAN = 2.0V VCLAMP(EA) With respect to VCM -0.2 +0.03 +0.2 A 883 930 976 mV 87.5 90 92.5 %VOUT POWER-GOOD AND OVERVOLTAGE PROTECTION PGOOD Trip Level PGOOD Output Low Level PGOOD Output Leakage Current OVI Trip Threshold OVI Input Bias Current VUV VPGLO IPG OVPTH PGOOD goes low when VOUT is below this threshold ISINK = 4mA PGOOD = VCC With respect to SGND 1.244 IOVI 1.276 0.4 V 1 A 1.308 0.2 V A ENABLE INPUT EN Input High Voltage VEN EN rising 2.437 EN Input Hysteresis EN Pullup Current 2.5 2.562 V 16.5 A 0.28 IEN 13.5 15 V THERMAL SHUTDOWN Thermal Shutdown Thermal Shutdown Hysteresis Temperature rising 150 C 30 C Note 1: Specifications at TA = +25C are 100% tested. Specifications over the temperature range are guaranteed by design. Note 2: Does not include an error due to finite error amplifier gain. See the Voltage-Error Amplifier (EAOUT) section. 4 _______________________________________________________________________________________ 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing VIN = 12V 20 VIN = 5V 300 500 700 900 28.0 27.5 27.0 26.5 VIN = 12V fSW = 250kHz 26.0 -40 1100 1300 1500 MAX16818 toc03 MAX16818 toc02 VIN = 12V fSW = 250kHz CDL/CDH = 22nF -15 10 35 85 60 0 1 2 3 4 TEMPERATURE (C) VOUT (V) HICCUP CURRENT LIMIT vs. REXT VCC LOAD REGULATION vs. INPUT VOLTAGE DRIVER RISE TIME vs. DRIVER LOAD CAPACITANCE 5.25 MAX16818 toc04 26.0 25.5 100 5.15 5 MAX16818 toc06 FREQUENCY (kHz) MAX16818 toc05 100 VIN = 12V fSW = 250kHz 80 VIN = 24V 24.5 5.05 VIN = 12V tR (ns) 25.0 VCC (V) CURRENT LIMIT (A) 64 60 0 60 DL 40 4.95 DH VIN = 5V 24.0 VIN = 12V fSW = 250kHz R1 = 1m VOUT = 1.5V 23.5 20 4.85 23.0 0 4.75 0 4 8 12 16 20 0 25 50 75 100 125 1 150 6 11 16 21 REXT (M) VCC LOAD CURRENT (mA) CAPACITANCE (nF) DRIVER FALL TIME vs. DRIVER LOAD CAPACITANCE HIGH-SIDE DRIVER (DH) SINK AND SOURCE CURRENT LOW-SIDE DRIVER (DL) SINK AND SOURCE CURRENT MAX16818 toc09 MAX16818 toc07 MAX16818 toc08 100 VIN = 12V fSW = 250kHz 80 tF (ns) 28.5 66 62 10 29.0 (VCSP - VCSN) (mV) VIN = 24V 40 30 68 SUPPLY CURRENT (mA) EXTERNAL CLOCK NO DRIVER LOAD 50 SUPPLY CURRENT (mA) 70 MAX16818 toc01 60 CURRENT-SENSE THRESHOLD vs. OUTPUT VOLTAGE SUPPLY CURRENT vs. TEMPERATURE SUPPLY CURRENT (IQ) vs. FREQUENCY CLOAD = 22nF VIN = 12V CLOAD = 22nF VIN = 12V 60 3A/div 2A/div DL 40 DH 20 0 1 6 11 16 21 100ns/div 100ns/div CAPACITANCE (nF) _______________________________________________________________________________________ 5 MAX16818 Typical Operating Characteristics (TA = +25C, using Figure 5, unless otherwise noted.) Typical Operating Characteristics (continued) (TA = +25C, using Figure 5, unless otherwise noted.) HIGH-SIDE DRIVER (DH) FALL TIME HIGH-SIDE DRIVER (DH) RISE TIME LOW-SIDE DRIVER (DL) RISE TIME MAX16818 toc11 MAX16818 toc10 MAX16818 toc12 CLOAD = 22nF VIN = 12V CLOAD = 22nF VIN = 12V CLOAD = 22nF VIN = 12V 2V/div 2V/div 2V/div 40ns/div 40ns/div 40ns/div MAX16818 toc13 10,000 2V/div fSW (kHz) CLOAD = 22nF VIN = 12V MAX16818 toc14 FREQUENCY vs. RT LOW-SIDE DRIVER (DL) FALL TIME VIN = 12V 1000 100 30 40ns/div 110 70 190 150 270 230 350 310 510 430 390 470 RT (k) FREQUENCY vs. TEMPERATURE VIN = 12V 258 256 SYNC, CLKOUT, AND LX WAVEFORM MAX16818 toc16 MAX16818 toc15 260 SYNC 5V/div 254 fSW (kHz) MAX16818 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing 252 CLKOUT 5V/div 250 VIN = 12V fSW = 250kHz 248 246 LX 10V/div 244 242 240 -40 -15 10 35 60 85 1s/div TEMPERATURE (C) 6 _______________________________________________________________________________________ 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing PIN NAME 1 PGND FUNCTION 2, 7 N.C. 3 DL Low-Side Gate Driver Output 4 BST Boost Flying Capacitor Connection. Reservoir capacitor connection for the high-side MOSFET driver supply. Connect a ceramic capacitor between BST and LX. Power-Supply Ground No Connection. Not internally connected. 5 LX Source connection for the high-side MOSFET. 6 DH High-Side Gate Driver Output. Drives the gate of the high-side MOSFET. 8, 22, 25 SGND Signal Ground. Ground connection for the internal control circuitry. Connect SGND and PGND together at one point near the IC. 9 CLKOUT Oscillator Output. Rising edge of CLKOUT is phase-shifted from the rising edge of DH by 180. 10 PGOOD Power-Good Output 11 EN 12 RT/SYNC Switching Frequency Programming and Chip-Enable Input. Connect a resistor from RT/SYNC to SGND to set the internal oscillator frequency. Drive RT/SYNC to synchronize the switching frequency with external clock. 13 V_IOUT Voltage Source Output Proportional to the Inductor Current. The voltage at V_IOUT = 135 x ILED x RS. 14 LIM Current-Limit Setting Input. Connect a resistor from LIM to SGND to set the hiccup current-limit threshold. Connect a capacitor from LIM to SGND to ignore short output overcurrent pulses. 15 OVI Overvoltage Protection. Connect OVI to DIFF. When OVI exceeds 12.7% above the programmed output voltage, DH is latched low and DL is latched high. Toggle EN or recycle the input power to reset the latch. 16 CLP Current-Error Amplifier Output. Compensate the current loop by connecting an RC network to ground. 17 EAOUT 18 EAN Voltage-Error Amplifier Inverting Input 19 DIFF Differential Remote-Sense Amplifier Output. DIFF is the output of a precision unity-gain amplifier whose inputs are SENSE+ and SENSE-. 20 CSN Current-Sense Differential Amplifier Negative Input. The differential voltage between CSN and CSP is amplified internally by the current-sense amplifier (gain = 34.5) to measure the inductor current. Output Enable. Drive high or leave unconnected for normal operation. Drive low to shut down the power drivers. EN has an internal 15A pullup current. Connect a capacitor from EN to SGND to program the hiccup-mode duty cycle. Voltage-Error Amplifier Output. Connect to the external compensation network. _______________________________________________________________________________________ 7 MAX16818 Pin Description 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing MAX16818 Pin Description (continued) 8 PIN NAME FUNCTION 21 CSP Current-Sense Differential Amplifier Positive Input. The differential voltage between CSN and CSP is amplified internally by the current-sense amplifier (gain = 34.5) to measure the inductor current. 23 SENSE- Differential LED Current-Sensing Negative Input. SENSE- is used to sense the LED current. Connect SENSE- to the negative side of the LED current-sense resistor. 24 SENSE+ Differential LED Current-Sensing Positive Input. SENSE+ is used to sense the LED current. Connect SENSE+ to the positive side of the LED current-sense resistor. 26 IN 27 VCC Internal +5V Regulator Output. VCC is derived from the IN voltage. Bypass VCC to SGND with 4.7F and 0.1F ceramic capacitors. 28 VDD Supply Voltage for Low-Side and High-Side Drivers. Connect a parallel combination of 0.1F and 1F ceramic capacitors to PGND and a 1 resistor to VCC to filter out the high peak currents of the driver from internal circuitry. -- EP Supply Voltage Connection. Connect IN to VCC for a +5V system. Exposed Paddle. Connect the exposed paddle to a copper pad (SGND) to improve power dissipation. _______________________________________________________________________________________ 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing ON/OFF R6 C3 R3 VLED R4 VIN 7V TO 28V VCC R5 C2 14 LIM C10 C9 13 12 V_IOUT RT/SYNC 9 10 PGOOD CLKOUT 11 EN L1 8 SGND 15 OVI N.C. 7 16 CLP DH 6 17 EAOUT LX 5 VLED D1 Q1 R12 R11 LED STRING C1 C8 R7 C7 18 EAN BST 4 MAX16818 R10 19 DIFF DL 3 20 CSN N.C. 2 R1 PGND 1 21 CSP SGND 22 R2 SENSE23 SENSE+ 24 SGND 25 IN 26 VDD 28 VCC 27 VCC VIN C6 R8 C5 C4 Figure 1. Typical Application Circuit for a Boost LED Driver (Nonsynchronous) _______________________________________________________________________________________ 9 MAX16818 Typical Application Circuits 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing MAX16818 Typical Application Circuits (continued) ON/OFF R6 C3 R3 VLED R4 VIN 7V TO 28V VCC R5 LED STRING 1 TO 6 LEDS R2 C2 14 LIM C10 C9 13 12 V_IOUT RT/SYNC 9 10 11 EN L1 8 SGND PGOOD CLKOUT 15 OVI N.C. 7 16 CLP DH 6 17 EAOUT LX 5 D1 VLED Q1 R12 VCC R11 RS+ VCC C8 R7 C7 18 EAN MAX4073T RS- BST 4 MAX16818 OUT C1 R10 19 DIFF DL 3 20 CSN N.C. 2 PGND 1 21 CSP SGND 22 R1 SENSE23 SENSE+ 24 SGND 25 IN 26 VCC 27 VDD 28 VCC VIN C6 R8 C5 C4 Figure 2. Typical Application Circuit for an Input-Referred Buck-Boost LED Driver (Input: 7V to 28V, Output: 1 to 6 LEDs in Series) 10 ______________________________________________________________________________________ 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing ON/OFF R6 C4 R3 VLED R4 VIN 7V TO 28V VCC R5 C3 14 LIM C10 13 12 9 10 11 EN 8 15 OVI SGND N.C. 7 16 CLP DH 6 17 EAOUT LX 5 C11 V_IOUT RT/SYNC L1 PGOOD CLKOUT C1 VLED D1 Q1 R12 R11 L2 C9 C8 18 EAN C2 LED STRING BST 4 MAX16818 R10 19 DIFF DL 3 20 CSN N.C. 2 R1 PGND 1 21 CSP SGND 22 R2 R7 SENSE23 SENSE+ 24 SGND 25 IN 26 VCC 27 VDD 28 VCC VIN C7 R8 C6 C5 Figure 3. Typical Application Circuit for a SEPIC LED Driver ______________________________________________________________________________________ 11 MAX16818 Typical Application Circuits (continued) 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing MAX16818 Typical Application Circuits (continued) ON/OFF C3 R3 VLED R4 VCC R5 14 13 12 9 10 15 OVI 16 CLP DH 6 V_IOUT RT/SYNC 11 EN VIN 7V TO 18V 8 SGND N.C. 7 LIM C11 C10 R6 PGOOD CLKOUT C2 Q1 R12 R11 L1 17 EAOUT VLED LX 5 C9 C4 R7 C8 D1 18 EAN Q3 BST 4 MAX16818 Q2 R10 19 DIFF DL 3 20 CSN N.C. 2 C1 LED STRING D2 R2 R1 PGND 1 21 CSP SGND 22 SENSE23 SENSE+ 24 SGND 25 IN 26 VCC 27 VDD 28 VCC VIN C7 R8 C6 C5 Figure 4. Application Circuit for a Ground-Referred Buck-Boost LED Driver 12 ______________________________________________________________________________________ 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing VCC R4 14 LIM C11 C10 R3 C3 13 12 VIN 7V TO 28V ON/OFF V_IOUT RT/SYNC 9 10 PGOOD CLKOUT 11 EN 8 SGND 15 OVI N.C. 7 16 CLP DH 6 17 EAOUT LX 5 C2 R10 R9 L1 C9 C4 R5 C8 18 EAN BST 4 MAX16818 Q1 D1 R8 19 DIFF DL 3 20 CSN N.C. 2 C1 LED STRING R2 R1 PGND 1 21 CSP SGND 22 SENSE23 SENSE+ 24 SGND 25 IN 26 VDD 28 VCC 27 VCC VIN C7 R6 C6 C5 Figure 5. Application Circuit for a Buck LED Driver ______________________________________________________________________________________ 13 MAX16818 Typical Application Circuits (continued) 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing MAX16818 Functional Diagram VCC IS EN 0.5V x VCC 5V LDO REGULATOR IN VCC UVLO POR TEMP SENSOR TO INTERNAL CIRCUITS LIM HICCUP MODE CURRENT LIMIT 126.7k MAX16818 VCM 100k 0.5 x VCLAMP CLP CA CSN Q R Q RT Ct AV = 34.5 CSP S VCM gm = 500S VDD PWM COMPARATOR CEA AV = 4 BST V_IOUT VCLAMP HIGH VCLAMP LOW SGND RAMP CPWM S Q DH LX 2 x fS (V/s) CLK RT/SYNC OSCILLATOR R Q DL CLKOUT RAMP GENERATOR DIFF +0.6V SENSESENSE+ PGND PGOOD N DIFF AMP 0.1 x VREF EAOUT ERROR AMP EAN 0.12 x VREF OVP LATCH VEA LATCH SOFTSTART OVP COMP VREF = 0.6V VCM (0.6V) CLEAR ON UVLO RESET OR ENABLE LOW OVI Figure 6. MAX16818 Functional Diagram 14 ______________________________________________________________________________________ 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing The MAX16818 is a high-performance average-currentmode PWM controller for high-power, high-brightness LEDs (HBLEDs). Average current-mode control is the ideal method for driving HBLEDs. This technique offers inherently stable operation, reduces component derating and size by accurately controlling the inductor current. The device achieves high efficiency at high current (up to 30A) with a minimum number of external components. The high- and low-side drivers source and sink up to 4A for lower switching losses while driving high-gate-charge MOSFETs. The MAX16818's CLKOUT output is 180 out-of-phase with respect to the high-side driver. CLKOUT drives a second MAX16818 LED driver out of phase, reducing the input-capacitor ripple current. The MAX16818 consists of an inner average current loop representing inductor current and an outer voltage loop voltage-error amplifier (VEA) that directly controls LED current. The combined action of the two loops results in a tightly regulated LED current. The inductor current is sensed across a current-sense resistor. The differential amplifier senses LED current through a sense resistor in series with the LEDs and the resulting sensed voltage is compared against an internal 0.6V reference at the erroramplifier input. The MAX16818 will adjust the LED current to within 1% accuracy to maintain emitted spectrum of the light in HBLEDs. IN, VCC, and VDD The MAX16818 accepts either a 4.75V to 5.5V or 7V to 28V input voltage range. All internal control circuitry operates from an internally regulated nominal voltage of 5V (VCC). For input voltages of 7V or greater, the internal VCC regulator steps the voltage down to 5V. The VCC output voltage is a regulated 5V output capable of sourcing up to 60mA. Bypass the VCC to SGND with 4.7F and 0.1F low-ESR ceramic capacitors for highfrequency noise rejection and stable operation. The MAX16818 uses VDD to power the low-side and high-side drivers. Isolate VDD from VCC with a 1 resistor and put a 1F capacitor in parallel with a 0.1F capacitor to ground to prevent high-current noise spikes created by the driver from disrupting internal circuitry. The TQFN is a thermally enhanced package and can dissipate up to 2.7W. The high-power packages allow the high-frequency, high-current converter to operate from a 12V or 24V bus. Calculate power dissipation in the MAX16818 as a product of the input voltage and the total VCC regulator output current (ICC). ICC includes quiescent current (IQ) and gate-drive current (IDD): PD = VIN x ICC ICC = IQ + [fSW x (QG1 + QG2)] where QG1 and QG2 are the total gate charge of the low-side and high-side external MOSFETs at VGATE = 5V, IQ is 3.5mA (typ), and fSW is the switching frequency of the converter. Undervoltage Lockout (UVLO) The MAX16818 includes an undervoltage lockout with hysteresis and a power-on-reset circuit for converter turn-on. The UVLO rising threshold is internally set at 4.35V with a 200mV hysteresis. Hysteresis at UVLO eliminates chattering during startup. Most of the internal circuitry, including the oscillator, turns on when the input voltage reaches 4V. The MAX16818 draws up to 3.5mA of current before the input voltage reaches the UVLO threshold. Soft-Start The MAX16818 has an internal digital soft-start for a monotonic, glitch-free rise of the output current. Softstart is achieved by the controlled rise of the error amplifier dominant input in steps using a 5-bit counter and a 5-bit DAC. The soft-start DAC generates a linear ramp from 0 to 0.7V. This voltage is applied to the error amplifier at a third (noninverting) input. As long as the soft-start voltage is lower than the reference voltage, the system converges to that lower reference value. Once the soft-start DAC output reaches 0.6V, the reference takes over and the DAC output continues to climb to 0.7V, assuring that it does not interfere with the reference voltage. Internal Oscillator The internal oscillator generates a clock with the frequency proportional to the inverse of RT. The oscillator frequency is adjustable from 125kHz to 1.5MHz with better than 8% accuracy using a single resistor connected from RT/SYNC to SGND. The frequency accuracy avoids the over-design, size, and cost of passive filter components like inductors and capacitors. Use the following equation to calculate the oscillator frequency: For 120k RT 500k: 6.25 x 1010 fSW RT = For 40k RT 120k: RT = 6.40 x 1010 fSW ______________________________________________________________________________________ 15 MAX16818 Detailed Description The oscillator also generates a 2VP-P voltage-ramp signal for the PWM comparator and a 180 out-of-phase clock signal for CLKOUT to drive a second LED regulator out-of-phase. Synchronization The MAX16818 can be easily synchronized by connecting an external clock to RT/SYNC. If an external clock is present, then the internal oscillator is disabled and the external clock is used to run the device. If the external clock is removed, the absence of clock for 32s is detected and the circuit starts switching from the internal oscillator. Pulling RT/SYNC to ground for at least 50s disables the converter. Use an open-collector transistor to synchronize the MAX16818 with the external system clock. Control Loop The MAX16818 uses an average-current-mode control scheme to regulate the output current (Figure 7). The main control loop consists of an inner current loop for controlling the inductor current and an outer current loop for regulating the LED current. The inner current loop absorbs the inductor pole reducing the order of the outer current loop to that of a single-pole system. The current loop consists of a current-sense resistor (RS), a current-sense amplifier (CA), a current-error amplifier (CEA), an oscillator providing the carrier ramp, and a PWM comparator (CPWM) (Figure 7). The precision CA amplifies the sense voltage across RS by a factor of 34.5. The inverting input to the CEA senses the CA output. The CEA output is the difference between the voltage-error amplifier output (EAOUT) and the amplified voltage from the CA. The RC compensation network connected to CLP provides external frequency compensation for the CEA. The start of every clock cycle enables the high-side drivers and initiates a PWM oncycle. Comparator CPWM compares the output voltage from the CEA with a 0V to 2V ramp from the oscillator. The PWM on-cycle terminates when the ramp voltage exceeds the error voltage. Compensation for the outer LED current loop varies based upon the topology. The MAX16818 outer LED current control loop consists of the differential amplifier (DIFF AMP), reference voltage, and VEA. The unity-gain differential amplifier provides true differential remote sensing of the voltage across the LED current set resistor, RLS. The differential amplifier output connects to the inverting input (EAN) of the VEA. The DIFF AMP is bypassed and the inverting input is available to the pin for direct feedback. The noninverting input of the VEA is internally connected to an internal precision reference voltage, set to 0.6V. The VEA controls the inner current loop (Figure 6). A feedback network compensates the outer loop using the EAOUT and EAIN pins. CCF RCF CCFF CSN CSP CA EAOUT SENSE+ Z COMP MAX16818 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing CLP VIN MAX16818 IL 600mV DIFF AMP SENSEEAN CEA VEA VREF + VCM = 1.2V CPWM LED STRING DRIVE COUT RLS DIFF RS Figure 7. MAX16818 Control Loop 16 ______________________________________________________________________________________ 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing Inductor Peak-Current Comparator The peak-current comparator provides a path for fast cycle-by-cycle current limit during extreme fault conditions, such as an inductor malfunction (Figure 8). Note the average current-limit threshold of 26.9mV still limits the output current during short-circuit conditions. To prevent inductor saturation, select an inductor with a saturation current specification greater than the average current limit. Proper inductor selection ensures that only the extreme conditions trip the peak-current comparator, such as an inductor with a shorted turn. The 60mV threshold for triggering the peak-current limit is twice the full-scale average current-limit voltage threshold. The peak-current comparator has only a 260ns delay. Current-Error Amplifier (For Inductor Currents) The MAX16818 has a transconductance current-error amplifier (CEA) with a typical gm of 550S and 320A output sink- and source-current capability. The currenterror amplifier output CLP serves as the inverting input to the PWM comparator. CLP is externally accessible to provide frequency compensation for the inner current loops (Figure 7). Compensate (CEA) so the inductor current negative slope, which becomes the positive slope to the inverting input of the PWM comparator, is less than the slope of the internally generated voltage ramp (see the Compensation section). PWM Comparator and R-S Flip-Flop The PWM comparator (CPWM) sets the duty cycle for each cycle by comparing the output of the current-error amplifier to a 2VP-P ramp. At the start of each clock cycle, an R-S flip-flop resets and the high-side driver (DH) goes high. The comparator sets the flip-flop as soon as the ramp voltage exceeds the CLP voltage, thus terminating the on-cycle (Figure 8). VDD PEAK-CURRENT COMPARATOR 60mV CLP AV = 34.5 CSP CA CSN MAX16818 gm = 550S BST CEA SET EAN Q S VEA DH CPWM RAMP EAOUT 2 x fS (V/s) LX CLK R CLR Q DL SHDN PGND Figure 8. MAX16818 Phase Circuit ______________________________________________________________________________________ 17 MAX16818 Inductor Current-Sense Amplifier The differential current-sense amplifier (CA) provides a DC gain of 34.5. The maximum input offset voltage of the current-sense amplifier is 1mV and the commonmode voltage range is 0 to 5.5V (IN = 7V to 28V). The current-sense amplifier senses the voltage across a current-sense resistor. The maximum common-mode voltage is 3.6V when VIN = 5V. MAX16818 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing Differential Amplifier BST The DIFF AMP facilitates remote sensing at the load (Figure 7). It provides true differential LED current (through the RLS sense resistor) sensing while rejecting the common-mode voltage errors due to high-current ground paths. The VEA provides the difference between the differential amplifier output (DIFF) and the desired LED current-sense voltage. The differential amplifier has a bandwidth of 3MHz. The difference between SENSE+ and SENSE- is regulated to 0.6V. Connect SENSE+ to the positive side of the LED currentsense resistor and SENSE- to the negative side of the LED current-sense resistor (which is often PGND). The MAX16818 uses VDD to power the low- and highside MOSFET drivers. The high-side driver derives its power through a bootstrap capacitor and VDD supplies power internally to the low-side driver. Connect a 0.47F low-ESR ceramic capacitor between BST and LX. Connect a Schottky rectifier from BST to VDD. Keep the loop formed by the boost capacitor, rectifier, and IC small on the PCB. MOSFET Gate Drivers (DH, DL) The high-side (DH) and low-side (DL) drivers drive the gates of external n-channel MOSFETs (Figures 1-5). The drivers' 4A peak sink- and source-current capability provides ample drive for the fast rise and fall times of the switching MOSFETs. Faster rise and fall times result in reduced cross-conduction losses. Due to physical realities, extremely low gate charges and R DS(ON) resistance of MOSFETs are typically exclusive of each other. MOSFETs with very low RDS(ON) will have a higher gate charge and vice versa. Choosing the high-side MOSFET (Q1) becomes a trade-off between these two attributes. Applications where the input voltage is much higher than the output voltage result in a low duty cycle where conduction losses are less important than switching losses. In this case, choose a MOSFET with very low gate charge and a moderate R DS(ON). Conversely, for applications where the output voltage is near the input voltage resulting in duty cycles much greater than 50%, the RDS(ON) losses become at least equal, or even more important than the switching losses. In this case, choose a MOSFET with very low RDS(ON) and moderate gate charge. Finally, for the applications where the duty cycle is near 50%, the two loss components are nearly equal, and a balanced MOSFET with moderate gate charge and RDS(ON) work best. In a buck topology, the low-side MOSFET (Q2) typically operates in a zero voltage switching mode, thus it does not have switching losses. Choose a MOSFET with very low RDS(ON) and moderate gate charge. Size both the high-side and low-side MOSFETs to handle the peak and RMS currents during overload conditions. The driver block also includes a logic circuit that provides an adaptive nonoverlap time to prevent shootthrough currents during transition. The typical nonoverlap time between the high-side and low-side MOSFETs is 35ns. 18 Protection The MAX16818 includes output overvoltage protection (OVP). During fault conditions when the load goes to high impedance (opens), the controller attempts to maintain LED current. The OVP protection disables the MAX16818 whenever the voltage exceeds the threshold, protecting the external circuits from undesirable voltages. Current Limit The VEA output is clamped to 930mV with respect to the common-mode voltage (V CM). Average-currentmode control has the ability to limit the average current sourced by the converter during a fault condition. When a fault condition occurs, the VEA output clamps to 930mV with respect to the common-mode voltage (0.6V) to limit the maximum current sourced by the converter to ILIMIT = 26.9mV / RS. The hiccup current limit overrides the average current limit. The MAX16818 includes hiccup current-limit protection to reduce the power dissipation during a fault condition. The hiccup current-limit circuit derives inductor current information from the output of the current amplifier. This signal is compared against one half of V CLAMP(EA) . With no resistor connected from the LIM pin to ground, the hiccup current limit is set at 90% of the full-load average current limit. Use REXT to increase the hiccup current limit from 90% to 100% of the full load average limit. The hiccup current limit can be disabled by connecting LIM to SGND. In this case, the circuit follows the average current-limit action during overload conditions. Overvoltage Protection The OVP comparator compares the OVI input to the overvoltage threshold. A detected overvoltage event latches the comparator output forcing the power stage into the OVP state. In the OVP state, the high-side MOSFET turns off and the low-side MOSFET latches on. Connect OVI to the center tap of a resistor-divider from VLED to SGND. In this case, the center tap is compared against 1.276V. Add an RC delay to reduce the sensitivity of the overvoltage circuit and avoid nuisance tripping of the converter. Disable the overvoltage function by connecting OVI to SGND. ______________________________________________________________________________________ 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing Application Circuit Descriptions This section provides some detail regarding the application circuits in the Simplified Diagram and Figures 1-5. The discussion includes some description of the topology as well as basic attributes. High-Frequency LED Current Pulser The Simplified Diagram shows the MAX16818 providing high-frequency, high-current pulses to the LEDs. The basic topology must be a buck, since the inductor always connects to the load in that configuration (in all other topologies, the inductor disconnects from the load at one time or another). The design minimizes the current ripple by oversizing the inductor, which allows for a very small (0.01F) output capacitor. When MOSFET Q3 turns on, it diverts the current around the LEDs at a very fast rate. Q3 also discharges the output capacitor, but since the capacitor is so small, it does not stress the MOSFET. Resistor R1 senses the LED/Q3 current and there is no reaction to the short that Q3 places across the LEDs. This design is superior in that it does not attempt to actually change the inductor current at high frequencies and yet the current in the LEDs varies from zero to full in very small periods of time. The efficiency of this technique is very high. Q3 must be able to dissipate the LED current applied to its RDS(ON) at some maximum duty cycle. If the circuit needs to control extremely high currents, use paralleled MOSFETs. PGOOD is low during LED pulsed-current operation. Boost LED Driver In Figure 1, the external components configure the MAX16818 as a boost converter. The circuit applies the input voltage to the inductor during the on-time, and then during the off-time the inductor, which is in series with the input capacitor, charges the output capacitor. Because of the series connection between the input voltage and the inductor, the output voltage can never go lower than the input voltage. The design is nonsynchronous, and since the current-sense resistor connects to ground, the power supply can go to any output voltage (above the input) as long as the components are rated appropriately. R2 again provides the sense voltage the MAX16818 uses to regulate the LED current. Input-Referenced LED Driver The circuit in Figure 2 shows a step-up/step-down regulator. It is similar to the boost converter in Figure 1 in that the inductor is connected to the input and the MOSFET is essentially connected to ground. However, rather than going from the output to ground, the LEDs span from the output to the input. This effectively removes the boost-only restriction of the regulator in Figure 1, allowing the voltage across the LEDs to be greater than or less than the input voltage. LED current sensing is not ground-referenced, so a high-side current-sense amplifier is used to measure current. SEPIC LED Driver Figure 3 shows the MAX16818 configured as a SEPIC LED driver. While buck topologies require the output to be lesser than the input, and boost topologies require the output to be greater than the input, a SEPIC topology allows the output voltage to be greater than, equal to, or less than the input. In a SEPIC topology, the voltage across C1 is the same as the input voltage, and L1 and L2 are the same inductance. Therefore, when Q1 conducts (on-time), both inductors ramp up current at the same rate. The output capacitor supports the output voltage during this time. During the off-time, L1 current recharges C1 and combines with L2 to provide current to recharge C2 and supply the load current. Since the voltage waveform across L1 and L2 are exactly the same, it is possible to wind both inductors on the same core (a coupled inductor). Although voltages on L1 and L2 are the same, RMS currents can be quite different so the windings may have a different gauge wire. Because of the dual inductors and segmented energy transfer, the efficiency of a SEPIC converter is somewhat lower than standard bucks or boosts. As in the boost driver, the current-sense resistor connects to ground, allowing the output voltage of the LED driver to exceed the rated maximum voltage of the MAX16818. Ground-Referenced Buck/Boost LED Driver Figure 4 depicts a buck/boost topology. During the ontime with this circuit, the current flows from the input capacitor, through Q1, L1, and Q3 and back to the input capacitor. During the off-time, current flows up through Q2, L1, D1, and to the output capacitor C1. This topology resembles a boost in that the inductor sits between the input and ground during the on-time. However, during the off-time the inductor resides between ground and the output capacitor (instead of between the input and output capacitors in boost topologies), so the output voltage can be any voltage less than, equal to, or greater than the input voltage. As compared to the SEPIC topology, the buck/boost does not require two inductors or a series capacitor, but it does require two additional MOSFETs. Buck Driver with Synchronous Rectification In Figure 5, the input voltage can go from 7V to 28V and, because of the ground-based current-sense resistor, the output voltage can be as high as the input. The synchro- ______________________________________________________________________________________ 19 MAX16818 Applications Information MAX16818 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing nous MOSFET keeps the power dissipation to a minimum, especially when the input voltage is large when compared to the voltage on the LED string. It is important to keep the current-sense resistor, R1, inside the LC loop, so that ripple current is available. To regulate the LED current, R2 creates a voltage that the differential amplifier compares to 0.6V. If power dissipation is a problem in R2, add a noninverting amplifier and reduce the value of the sense resistor accordingly. Inductor Selection The switching frequencies, peak inductor current, and allowable ripple at the output determine the value and size of the inductor. Selecting higher switching frequencies reduces the inductance requirement, but at the cost of lower efficiency. The charge/discharge cycle of the gate and drain capacitances in the switching MOSFETs create switching losses. The situation worsens at higher input voltages, since switching losses are proportional to the square of the input voltage. The MAX16818 can operate up to 1.5MHz, however for VIN > +12V, use lower switching frequencies to limit the switching losses. The following discussion is for buck or continuous boost-mode topologies. Discontinuous boost, buckboost, and SEPIC topologies are quite different in regards to component selection. Use the following equations to determine the minimum inductance value: Buck regulators: LMIN = (VINMAX - VLED) x VLED VINMAX x fSW x IL Boost regulators: LMIN = (VLED - VINMAX) x VINMAX VLED x fSW x IL where VLED is the total voltage across the LED string. As a first approximation choose the ripple current, IL, equal to approximately 40% of the output current. Higher ripple current allows for smaller inductors, but it also increases the output capacitance for a given voltage ripple requirement. Conversely, lower ripple current increases the inductance value, but allows the output capacitor to reduce in size. This trade-off can be altered once standard inductance and capacitance values are chosen. Choose inductors from the standard surface-mount inductor series available from various manufacturers. 20 For example, for a buck regulator and 2 LEDs in series, calculate the minimum inductance at VIN(MAX) = 13.2V, VLED = 7.8V, IL = 400mA, and fSW = 330kHz: Buck regulators: LMIN = (13.2 - 7.8) x 7.8 = 24.2H 13.2 x 330k x 0.4 For a boost regulator with four LEDs in series, calculate the minimum inductance at VIN(MAX) = 13.2V, VLED = 15.6V, IL =400mA, and fSW = 330kHz: Boost regulators: LMIN = (15.6 - 13.2) x 13.2 = 15.3H 15.6 x 330k x 0.4 The average-current-mode control feature of the MAX16818 limits the maximum peak inductor current and prevents the inductor from saturating. Choose an inductor with a saturating current greater than the worst-case peak inductor current. Use the following equation to determine the worst-case inductor current: ILPEAK = VCL IL + RS 2 where R S is the inductor sense resistor and V CL = 0.0282V. Switching MOSFETs When choosing a MOSFET for voltage regulators, consider the total gate charge, RDS(ON), power dissipation, and package thermal impedance. The product of the MOSFET gate charge and on-resistance is a figure of merit, with a lower number signifying better performance. Choose MOSFETs optimized for high-frequency switching applications. The average current from the MAX16818 gate-drive output is proportional to the total capacitance it drives at DH and DL. The power dissipated in the MAX16818 is proportional to the input voltage and the average drive current. See the IN, V CC , and V DD section to determine the maximum total gate charge allowed from the combined driver outputs. The gate-charge and drain-capacitance (CV2) loss, the cross-conduction loss in the upper MOSFET due to finite rise/fall times, and the I 2 R loss due to RMS current in the MOSFET RDS(ON) account for the total losses in the MOSFET. ______________________________________________________________________________________ 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing Boost Regulator Estimate the power loss (PDMOS_) caused by the MOSFET using the following equations: PDMOS - HI = (QG x VDD x fSW ) + PDFET = (QG x VDD x fSW ) + VIN x IOUT x (tR + tF) x fSW + (RDS(ON) x IRMS - HI2) 2 VIN x IOUT x (tR + tF) x fSW 2 2 + (RDS(ON) x IRMS - HI ) IRMS - HI = where QG, RDS(ON), tR, and tF are the upper-switching MOSFET's total gate charge, on-resistance at maximum operating temperature, rise time, and fall time, respectively. IRMS - HI = (IVALLEY2 + IPK 2 + IVALLEY x IPK ) x D 3 For the buck regulator, D = V LEDs / V IN, I VALLEY = (IOUT - IL / 2) and IPK = (IOUT + IL / 2). PDMOS - LO = (QG x VDD x fSW ) + (RDS(ON) x IRMS - LO2) IRMS - LO = (IVALLEY2 + IPK2 + IVALLEY x IPK) x (1- D) 3 For example, from the typical specifications in the Applications Information section with VOUT = 7.8V, the high-side and low-side MOSFET RMS currents are 0.77A and 0.63A, respectively, for a 1A buck regulator. Ensure that the thermal impedance of the MOSFET package keeps the junction temperature at least +25C below the absolute maximum rating. Use the following equation to calculate the maximum junction temperature: TJ = (PDMOS x JA) + TA, where JA and TA are the junction-to-ambient thermal impedance and ambient temperature, respectively. To guarantee that there is no shoot-through from VIN to PGND, the MAX16818 produces a nonoverlap time of 35ns. During this time, neither high- nor low-side MOSFET is conducting, and since the output inductor must maintain current flow, the intrinsic body diode of the low-side MOSFET becomes the conduction path. Since this diode has a fairly large forward voltage, a Schottky diode (in parallel to the low-side MOSFET) diverts current flow from the MOSFET body diode because of its lower forward voltage, which, in turn, increases efficiency. (IVALLEY2 + IPK 2 + IVALLEY x IPK ) x D 3 For a boost regulator in continuous mode, D = VLEDs / (VIN + VLEDs), IVALLEY = (IOUT - IL / 2) and IPK = (IOUT + IL / 2). The voltage across the MOSFET: VMOSFET = VLED + VF where VF is the maximum forward voltage of the diode. The output diode on a boost regulator must be rated to handle the LED series voltage, VLED. It should also have fast reverse-recovery characteristics and should handle the average forward current that is equal to the LED current. Input Capacitors For buck regulator designs, the discontinuous input current waveform of the buck converter causes large ripple currents in the input capacitor. The switching frequency, peak inductor current, and the allowable peakto-peak voltage ripple reflected back to the source dictate the capacitance requirement. Increasing switching frequency or paralleling out-of-phase converters lowers the peak-to-average current ratio, yielding a lower input capacitance requirement for the same LED current. The input ripple is comprised of VQ (caused by the capacitor discharge) and VESR (caused by the ESR of the capacitor). Use low-ESR ceramic capacitors with high-ripple-current capability at the input. Assume the contributions from the ESR and capacitor discharge are equal to 30% and 70%, respectively. Calculate the input capacitance and ESR required for a specified ripple using the following equation: ESRIN = VESR IL IOUT + 2 ______________________________________________________________________________________ 21 MAX16818 Buck Regulator Estimate the power loss (PDMOS_) caused by the high-side and low-side MOSFETs using the following equations: MAX16818 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing Current Limit Buck: I x D(1- D) CIN = OUT VQ x fSW where IOUT is the output current of the converter. For example, at VIN = 13.2V, VLED = 7.8V, IOUT = 1A, IL = 0.4A, and fSW = 330kHz, the ESR and input capacitance are calculated for the input peak-to-peak ripple of 100mV or less yielding an ESR and capacitance value of 25m and 10F. For boost regulator designs, the input-capacitor current waveform is dominated by the inductor, a triangle wave a magnitude of IL. For simplicity's sake, the current waveform can be approximated by a square wave with a magnitude that is half that of the triangle wave. Calculate the input capacitance and ESR required for a specified ripple using the following equation: ESRIN = VESR IL Boost: IL x D 2 CIN = VQ x fSW Duty cycle, D, for a boost regulator is equal to (VOUT VIN) / VOUT. As an example, at VIN = 13.2V, VLED = 15.6V, IOUT = 1A, IL = 0.4A, and fSW = 330kHz, the ESR and input capacitance are calculated for the input peak-to-peak ripple of 100mV or less yielding an ESR and capacitance value of 250m and 1F, respectively. Output Capacitor For buck converters, the inductor always connects to the load, so the inductance controls the ripple current. The output capacitance shunts a fraction of this ripple current and the LED string absorbs the rest. The capacitor reactance (which includes the capacitance and ESR) and the dynamic impedance of the LED diode string form a conductance divider that splits the ripple current between the LEDs and the capacitor. In many cases, the capacitor is very large as compared to the ESR, and this divider reduces to the ESR and the LED resistance. In addition to the average current limit, the MAX16818 also has hiccup current limit. The hiccup current limit is set to 10% below the average current limit to ensure that the circuit goes in hiccup mode during continuous output short circuit. Connecting a resistor from LIM to ground increases the hiccup current limit, while shorting LIM to ground disables the hiccup current-limit circuit. Average Current Limit The average-current-mode control technique of the MAX16818 accurately limits the maximum output current. The MAX16818 senses the voltage across the sense resistor and limit the peak inductor current (I L-PK ) accordingly. The on-cycle terminates when the currentsense voltage reaches 25.5mV (min). Use the following equation to calculate the maximum current-sense resistor value: RS = PDR = 0.0255 IOUT 0.75 x 10 - 3 RS where PDR is the dissipation in the series resistors. Select a 5% lower value of RS to compensate for any parasitics associated with the PCB. Also, select a noninductive resistor with the appropriate power rating. Hiccup Current Limit The hiccup current-limit value is always 10% lower than the average current-limit threshold, when LIM is left unconnected. Connect a resistor from LIM to SGND to increase the hiccup current-limit value from 90% to 100% of the average current-limit value. The average current-limit architecture accurately limits the average output current to its current-limit threshold. If the hiccup current limit is programmed to be equal or above the average current-limit value, the output current does not reach the point where the hiccup current limit can trigger. Program the hiccup current limit at least 5% below the average current limit to ensure that the hiccup current-limit circuit triggers during overload. See the Hiccup Current Limit vs. R EXT graph in the Typical Operating Characteristics. Boost converters place a harsher requirement on the output capacitors as they must sustain the full load during the on-time of the MOSFET and are replenished during the off-time. The ripple current in this case is the full load current, and the holdup time is equal to the duty cycle times the switching period. 22 ______________________________________________________________________________________ 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing RCF VRAMP x fSW x L A V x gm x RS x VLED where VRAMP = 2V, gm = 550S, and AV = 34.5. RCF 105 x fSW x L RS x VLED Boost: VRAMP x fSW x L RCF A V x gm x RS x ( VLED - VIN ) RCF 10 05 x fSW x L RS x ( VLED - VIN ) The crossover frequency of the inner current loop is expressed as: Buck: fC _ buck = A V x gm x RS x VIN x RCF VRAMP x 2 x L fC _ buck = MAX16818 Compensation The main control loop consists of an inner current loop (inductor current) and an outer LED current loop. The MAX16818 uses an average current-mode control scheme to regulate the LED current (Figure 7). The VEA output provides the controlling voltage for the current source. The inner current loop absorbs the inductor pole reducing the order of the LED current loop to that of a single-pole system. The major consideration when designing the current control loop is making certain that the inductor downslope (which becomes an upslope at the output of the CEA) does not exceed the internal ramp slope. This is a necessary condition to avoid subharmonic oscillations similar to those in peak current mode with insufficient slope compensation. This requires that the resistance, RCF, at the output of the CEA be limited, based on the following equation (Figure 6): Buck: (9.488mS V ) x RS x VIN x RCF 2 x L Boost: fC _ boost = which becomes: fC _ boost = A V x gm x RS x VLED x RCF VRAMP x 2 x L (9.488mS V ) x RS x VLED x RCF 2 x L For adequate phase margin, place the zero formed by RCF and CCZ not more than 1/3 to 1/5 of the crossover frequency. The pole formed by RCF and CCP may not be required in most applications but can be added to minimize noise at a frequency at or above the switching frequency. Power Dissipation The TQFN is a thermally enhanced package and can dissipate about 2.7W. The high-power package makes the high-frequency, high-current LED driver possible to operate from a 12V or 24V bus. Calculate power dissipation in the MAX16818 as a product of the input voltage and the total VCC regulator output current (ICC). ICC includes quiescent current (IQ) and gate drive current (IDD): PD = VIN x ICC ICC = IQ + [fSW x (QG1 + QG2)] where QG1 and QG2 are the total gate charge of the lowside and high-side external MOSFETs at VGATE = 5V, IQ is estimated from the Supply Current (IQ) vs. Frequency graph in the Typical Operating Characteristics, and fSW is the switching frequency of the LED driver. For boost drivers, only consider one gate charge, QG1. Use the following equation to calculate the maximum power dissipation (PDMAX) in the chip at a given ambient temperature (TA): PDMAX = 34.5 x (150 - TA) mW. When AV = 34.5, gm = 550S, and VRAMP = 2V, this becomes: ______________________________________________________________________________________ 23 Pin Configuration 24 CSN DIFF EAN EAOUT CLP OVI 19 18 17 16 15 SGND 22 14 LIM SENSE- 23 13 V_IOUT SENSE+ 24 12 RT/SYNC SGND 25 IN 26 VCC 27 VDD MAX16818 11 EN 10 PGOOD 9 CLKOUT 8 SGND * EXPOSED PAD 28 3 4 5 6 7 N.C. 2 DH 1 LX + BST 6) Run the current-sense lines CSP and CSN very close to each other to minimize the loop area. Similarly, run the remote voltage-sense lines SENSE+ and SENSE- close to each other. Do not cross these critical signal lines through power circuitry. Sense the current right at the pads of the current-sense resistors. 7) Avoid long traces between the VDD bypass capacitors, the driver output of the MAX16818, the MOSFET gates, and PGND. Minimize the loop formed by the VCC bypass capacitors, bootstrap diode, bootstrap capacitor, the MAX16818, and the upper MOSFET gate. 8) Distribute the power components evenly across the board for proper heat dissipation. 9) Provide enough copper area at and around the switching MOSFETs, inductor, and sense resistors to aid in thermal dissipation. 10) Use wide copper traces (2oz) to keep trace inductance and resistance low to maximize efficiency. Wide traces also cool heat-generating components. 20 DL 4) Place the Schottky diodes close to the lower MOSFETs and on the same side of the PCB. 5) Keep the SGND and PGND isolated and connect them at one single point. 21 N.C. 2) Minimize the area and length of the high current loops from the input capacitor, upper switching MOSFET, inductor, and output capacitor back to the input capacitor negative terminal. 3) Keep short the current loop formed by the lower switching MOSFET, inductor, and output capacitor. TOP VIEW CSP PCB Layout Guidelines Use the following guidelines to layout the switching voltage regulator: 1) Place the IN, V CC , and V DD bypass capacitors close to the MAX16818. PGND MAX16818 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing TQFN Chip Information TRANSISTOR COUNT: 5654 PROCESS: BiCMOS Package Information For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. PACKAGE TYPE PACKAGE CODE DOCUMENT NO. 28 TQFN T2855-3 21-0140 ______________________________________________________________________________________ 1.5MHz, 30A High-Efficiency, LED Driver with Rapid LED Current Pulsing REVISION NUMBER REVISION DATE 0 10/06 Initial release 1 6/08 Replaced Compensation section and corrected Figure 4. 2 3/09 Updated formula in Inductor Selection section. DESCRIPTION PAGES CHANGED -- 12, 23 20 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 25 (c) 2009 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc. MAX16818 Revision History