LM5111-1MX/NOPB - NATIONAL SEMICONDUCTOR

LM5111

INB

INA

0.1 µF

1.0 µF

N/C

INA

VEE

INB

N/C

OUTA

VCC

OUTB

Product

Folder

Order

Now

Technical

Documents

Tools &

Software

Support &

Community

Reference

Design

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

LM5111

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

LM5111 Dual 5-A Compound Gate Driver

1 Features

1• Independently Drives Two N-Channel MOSFETs

• Compound CMOS and Bipolar Outputs Reduce

Output Current Variation

• 5-A Sink and 3-A Source Current Capability

• Two Channels can be Connected in Parallel to

Double the Drive Current

• Independent Inputs (TTL Compatible)

• Fast Propagation Times (25 ns Typical)

• Fast Rise and Fall Times (14 ns and 12 ns Rise

and Fall, Respectively, With 2-nF Load)

• Available in Dual Noninverting, Dual Inverting and

Combination Configurations

• Supply Rail Undervoltage Lockout Protection

(UVLO)ƒ

• LM5111-4 UVLO Configured to Drive PFET

through OUT_A and NFET through OUT_B

• Pin Compatible With Industry Standard Gate

Drivers

2 Applications

• Synchronous Rectifier Gate Drivers

• Switch-mode Power Supply Gate Driver

• Solenoid and Motor Drivers

3 Description

The LM5111 Dual Gate Driver replaces industry

standard gate drivers with improved peak output

current and efficiency. Each compound output driver

stage includes MOS and bipolar transistors operating

in parallel that together sink more than 5-A peak from

capacitive loads. Combining the unique

characteristics of MOS and bipolar devices reduces

drive current variation with voltage and temperature.

Undervoltage lockout protection is also provided. The

drivers can be operated in parallel with inputs and

outputs connected to double the drive current

capability. This device is available in the SOIC

package or the thermally enhanced MSOP-

PowerPAD package.

Device Information(1)

PART NUMBER PACKAGE BODY SIZE (NOM)

LM5111 SOIC (8) 5.00 mm x 6.00 mm

MSOP-PowerPAD (8) 3.00 mm x 4.90 mm

(1) For all available packages, see the orderable addendum at

the end of the data sheet.

Simplified Application Diagram

LM5111

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

www.ti.com

Product Folder Links: LM5111

Table of Contents

1 Features.................................................................. 1

2 Applications ........................................................... 1

3 Description............................................................. 1

4 Revision History..................................................... 2

5 Device Options....................................................... 3

6 Pin Configuration and Functions......................... 3

7 Specifications......................................................... 4

7.1 Absolute Maximum Ratings ...................................... 4

7.2 ESD Ratings.............................................................. 4

7.3 Recommended Operating Conditions....................... 4

7.4 Thermal Information.................................................. 4

7.5 Electrical Characteristics........................................... 5

7.6 Switching Characteristics.......................................... 5

7.7 Typical Characteristics.............................................. 7

8 Detailed Description.............................................. 9

8.1 Overview................................................................... 9

8.2 Functional Block Diagram......................................... 9

8.3 Feature Description................................................. 10

8.4 Device Functional Modes........................................ 10

9 Application and Implementation ........................ 11

9.1 Application Information............................................ 11

9.2 Typical Application ................................................. 11

10 Power Supply Recommendations ..................... 13

10.1 Bias Supply Voltage.............................................. 13

11 Layout................................................................... 13

11.1 Layout Guidelines ................................................. 13

11.2 Layout Example .................................................... 14

11.3 Thermal Considerations........................................ 14

12 Device and Documentation Support................. 17

12.1 Receiving Notification of Documentation Updates 17

12.2 Community Resources.......................................... 17

12.3 Trademarks........................................................... 17

12.4 Electrostatic Discharge Caution............................ 17

12.5 Glossary................................................................ 17

13 Mechanical, Packaging, and Orderable

Information........................................................... 17

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision G (March 2013) to Revision H Page

• Added Device Information table, Pin Configuration and Functions section, Specifications section, ESD Ratings table,

Recommended Operating Conditions table, Thermal Information table, Feature Description section, Device

Functional Modes section, Application and Implementation section, Power Supply Recommendations section,

Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information

section ................................................................................................................................................................................... 1

Changes from Revision F (March 2013) to Revision G Page

• Changed layout of National Semiconductor Data Sheet to TI format .................................................................................. 16

OUT A

4 5

IN_A

VEE

IN_B

VCC

OUT_B

LM5111

www.ti.com

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

Product Folder Links: LM5111

5 Device Options

Table 1. Configuration Table

PART NUMBER "A" OUTPUT CONFIGURATION "B" OUTPUT CONFIGURATION PACKAGE

LM5111-1M/-1MX/-1MY/-1MYX Noninverting (Low in UVLO) Noninverting (Low in UVLO) SOIC, MSOP-PowerPAD

LM5111-2M/-2MX/-2MY/-2MYX Inverting (Low in UVLO) Inverting (Low in UVLO) SOIC, MSOP-PowerPAD

LM5111-3M/-3MX/-3MY/-3MYX Inverting (Low in UVLO) Noninverting (Low in UVLO) SOIC, MSOP-PowerPAD

LM5111-4M/-4MX/-4MY/-4MYX Inverting (High in UVLO) Noninverting (Low in UVLO) SOIC, MSOP-PowerPAD

(1) Only available with the MSOP-PowerPAD package.

6 Pin Configuration and Functions

D and DGN Package

8-Pin SOIC and MSOP-PowerPAD

Top View

Pin Functions

PIN I/O DESCRIPTION

NAME NO.

IN_A 2 I ‘A’ side control input. TTL compatible thresholds.

IN_B 4 I ‘B’ side control input. TTL compatible thresholds.

OUT_A. 7 O Output for the ‘A’ side driver. Voltage swing of this output is from VCC to VEE. The output stage is

capable of sourcing 3 A and sinking 5 A.

OUT_B 5 O Output for the ‘B’ side driver. Voltage swing of this output is from VCC to VEE. The output stage is

capable of sourcing 3 A and sinking 5 A.

VCC 6 — Positive output supply. Locally decouple to VEE.

VEE 3 — Ground reference for both inputs and outputs. Connect to power ground.

NC 1, 8 — No Connection

Exposed Pad(1) —It is recommended that the exposed pad on the bottom of the package be soldered to ground plane on

the PC board to aid thermal dissipation.

LM5111

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

www.ti.com

Product Folder Links: LM5111

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings

only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended

Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and

specifications.

7 Specifications

7.1 Absolute Maximum Ratings

see (1)(2)

MIN MAX UNIT

VCC to VEE −0.3 15 V

IN to VEE −0.3 15 V

Maximum junction temperature, TJ(max) 150 °C

Storage temperature, Tstg −55 150 °C

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

7.2 ESD Ratings VALUE UNIT

V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) 2000 V

7.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT

TJOperating junction temperature 125 °C

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application

report.

7.4 Thermal Information

THERMAL METRIC(1)

LM5111

UNIT

(SOIC) DGN

(MSOP-PowerPAD)

8 PINS 8 PINS

RθJA Junction-to-ambient thermal resistance 112.2 50.7 °C/W

RθJC(top) Junction-to-case (top) thermal resistance 54.6 56.6 °C/W

RθJB Junction-to-board thermal resistance 53.1 35.9 °C/W

ψJT Junction-to-top characterization parameter 9.4 5.3 °C/W

ψJB Junction-to-board characterization parameter 52.5 35.6 °C/W

RθJC(bot) Junction-to-case (bottom) thermal resistance N/A 4.4 °C/W

LM5111

www.ti.com

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

Product Folder Links: LM5111

(1) The output resistance specification applies to the MOS device only. The total output current capability is the sum of the MOS and

Bipolar devices.

7.5 Electrical Characteristics

TJ=−40°C to +125°C, VCC = 12 V, VEE = 0 V, No Load on OUT_A or OUT_B, unless otherwise specified.

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

VCC operating range VCC−VEE 3.5 14 V

VCCR VCC undervoltage lockout (rising) VCC−VEE 2.3 2.9 3.5 V

VCCH VCC undervoltage lockout hysteresis 230 mV

ICC VCC supply current (ICC)IN_A = IN_B = 0 V (5111-1) 1 2 mAIN_A = IN_B = VCC (5111-2) 1 2

IN_A = VCC, IN_B = 0 V (5111-3) 1 2

CONTROL INPUTS

VIH Logic high 2.2 V

VIL Logic low 0.8 V

VthH High threshold 1.3 1.75 2.2 V

VthL Low threshold 0.8 1.35 2 V

HYS Input hysteresis 400 mV

IIL Input current low IN_A=IN_B=VCC (5111-1-2-3) –1 0.1 1

µA

IIH Input current high

IN_B=VCC (5111-3) 10 18 25

IN_A=IN_B=VCC (5111-2) –1 0.1 1

IN_A=IN_B=VCC (5111-1) 10 18 25

IN_A=VCC (5111-3) –1 0.1 1

OUTPUT DRIVERS

ROH Output resistance high IOUT =−10 mA(1) 30 50 Ω

ROL Output resistance low IOUT = + 10 mA(1) 1.4 2.5 Ω

ISource Peak source current OUTA/OUTB = VCC/2,

200-ns Pulsed Current 3 A

ISink Peak sink current OUTA/OUTB = VCC/2,

200-ns Pulsed Current 5 A

LATCHUP PROTECTION

AEC - Q100, method 004 TJ= 150°C 500 mA

THERMAL RESISTANCE

θJA Junction to ambient,

0 LFPM air flow SOIC Package 170 °C/W

MSOP-PowerPAD Package 60

θJC Junction to case SOIC Package 70 °C/W

MSOP-PowerPAD Package 4.7

(1) See Figure 1 and Figure 2.

7.6 Switching Characteristics

over operating free-air temperature range (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

td1 Propagation delay time low to high,

IN rising (IN to OUT) CLOAD = 2 nF(1) 25 40 ns

td2 Propagation delay time high to low,

IN falling (IN to OUT) CLOAD = 2 nF(1) 25 40 ns

trRise time CLOAD = 2 nF(1) 14 25 ns

tfFall time CLOAD = 2 nF(1) 12 25 ns

INPUT

OUTPUT

tD1

tD2

90%

10%

50%

INPUT

OUTPUT

tD1

tD2

90%

10%

50%

LM5111

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

www.ti.com

Product Folder Links: LM5111

Figure 1. Inverting

Figure 2. Noninverting

100 1k 10k

CAPACITIVE LOAD (pF)

TIME (ns)

TA = 25°C

VCC = 12V

46 8 10 12 14 16

SUPPLY VOLTAGE (V)

17.5

22.5

27.5

32.5

TIME (ns)

tD2

tD1

TA = 25°C

CL = 2200pF

-75 -50 -25 0 25 50 75 100 125 150 175

TIME (ns)

TEMPERATURE (°C)

VCC = 12V

CL = 2200pF

46910 12 13 16

TIME (ns)

SUPPLY VOLTAGE (V)

57811 14 15

TA = 25°C

CL = 2200pF

110 100 1000

FREQUENCY (kHz)

0.1

100

SUPPLY CURRENT (mA)

VCC = 15V

VCC = 10V

VCC = 5V

TA = 25°C

CL = 2200pF

100

10k

CAPACITIVE LOAD (pF)

0.1

1000

SUPPLY CURRENT (mA)

f = 500kHz

f = 100kHz

f = 10kHz

TA = 25°C

VCC = 12V

LM5111

www.ti.com

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

Product Folder Links: LM5111

7.7 Typical Characteristics

Figure 3. Supply Current vs Frequency Figure 4. Supply Current vs Capacitive Load

Figure 5. Rise and Fall Time vs Supply Voltage Figure 6. Rise and Fall Time vs Temperature

Figure 7. Rise and Fall Time vs Capacitive Load Figure 8. Delay Time vs Supply Voltage

-75 -50 -25 0 25 50 75 100 125 150 175

1.600

1.900

2.200

2.500

2.800

3.100

UVLO THRESHOLDS (V)

TEMPERATURE (°C)

0.150

0.210

0.270

0.330

0.450

0.390

HYSTERESIS (V)

VCCR

VCCF

VCCH

-75 -50 -25 0 25 50 75 100 125 150 175

17.5

22.5

27.5

32.5

TIME (ns)

TEMPERATURE (°C)

tD2

tD1

VCC = 12V

CL = 2200pF

03 6 9 12 15 18

SUPPLY VOLTAGE (V)

0.75

1.25

1.75

2.25

2.75

3.25

ROL (:)

ROH (:)

ROH

ROL

TA = 25°C

IOUT = 10mA

LM5111

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

www.ti.com

Product Folder Links: LM5111

Typical Characteristics (continued)

Figure 9. Delay Time vs Temperature Figure 10. RDSON vs Supply Voltage

Figure 11. UVLO Thresholds and Hysteresis vs Temperature

UVLO

VEE

IN_A

VCC

OUT_A

VEE

OUT_B

VEE

IN_B

LM5111

www.ti.com

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

Product Folder Links: LM5111

8 Detailed Description

8.1 Overview

LM5111 dual gate driver consists of two independent and identical driver channels with TTL compatible logic

inputs and high current totem-pole outputs that source or sink current to drive MOSFET gates. The driver output

consist of a compound structure with MOS and bipolar transistor operating in parallel to optimize current

capability over a wide output voltage and operating temperature range. The bipolar device provides high peak

current at the critical threshold region of the MOSFET VGS while the MOS devices provide rail-to-rail output

swing. The totem pole output drives the MOSFET gate between the gate drive supply voltage VCC and the power

ground potential at the VEE pin.

The control inputs of the drivers are high impedance CMOS buffers with TTL compatible threshold voltages. The

LM5111 pinout was designed for compatibility with industry standard gate drivers in single supply gate driver

applications.

The input stage of each driver should be driven by a signal with a short rise and fall time. Slow rising and falling

input signals, although not harmful to the driver, may result in the output switching repeatedly at a high

frequency.

8.2 Functional Block Diagram

LM5111

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

www.ti.com

Product Folder Links: LM5111

8.3 Feature Description

8.3.1 Undervoltage Lockout

An undervoltage lockout (UVLO) circuit is included in the LM5111, which senses the voltage difference between

VCC and the chip ground pin, VEE. When the VCC to VEE voltage difference falls below 2.8 V both driver channels

are disabled. The UVLO hysteresis prevents chattering during brown-out conditions and the driver resumes

normal operation when the VCC to VEE differential voltage exceeds approximately 3 V.

The LM5111-1, -2, and -3 devices hold both outputs in the low state in the UVLO condition. The LM5111-4 is

distinguished from the LM5111-3 by the active high output state of OUT_A during UVLO. When VCC is less than

the UVLO threshold voltage, OUT_A of the LM5111-4 will be locked in the high state while OUT_B will be

disabled in the low state. This configuration allows the LM5111-4 to drive a PFET through OUT_A and an NFET

through OUT_B with both FETs safely turned off during UVLO.

8.3.2 Output Stage

The two driver channels of the LM5111 are designed as identical cells. Transistor matching inherent to integrated

circuit manufacturing ensures that the AC and DC peformance of the channels are nearly identical. Closely

matched propagation delays allow the dual driver to be operated as a single with inputs and output pins

connected. The drive current capability in parallel operation is precisely 2× the drive of an individual channel.

Small differences in switching speed between the driver channels will produce a transient current (shoot-through)

in the output stage when two output pins are connected to drive a single load. Differences in input thresholds

between the driver channels will also produce a transient current (shoot-through) in the output stage. Fast

transition input signals are especially important while operating in a parallel configuration. The efficiency loss for

parallel operation has been characterized at various loads, supply voltages and operating frequencies. The

power dissipation in the LM5111 increases be less than 1% relative to the dual driver configuration when

operated as a single driver with inputs/ outputs connected.

8.4 Device Functional Modes

Table 2. Input/output Logic Table

LM5111-1M LM5111-2M LM5111-3M/LM5111-4M

IN A IN B OUT A OUT B IN A IN B OUT A OUT B IN A IN B OUT A OUT B

L L L L L L H H L L H L

L H L H L H H L L H H H

H L H L H L L H H L L L

H H H H H H L L H H L H

In UVLO L L In UVLO L L In UVLO L/H L/L

LM5111

INB

INA

0.1 µF

1.0 µF

N/C

INA

VEE

INB

N/C

OUTA

VCC

OUTB

LM5111

www.ti.com

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

Product Folder Links: LM5111

9 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers should

validate and test their design implementation to confirm system functionality.

9.1 Application Information

High-frequency power supplies often require high-speed, high-current drivers such as the LM5111 family. A

leading application is the need to provide a high-power buffer stage between the PWM output of the control IC

and the gates of the primary power MOSFET or IGBT switching devices. In other cases, the driver IC is used to

drive the power-device gates through a drive transformer. Synchronous rectification supplies are also needed to

simultaneously drive multiple devices which presents an extremely large load to the control circuitry.

Driver ICs are used when use of the primary PWM regulator IC to directly drive the switching devices for one or

more reasons is not feasible. The PWMIC does not have the brute drive capability required for the intended

switching MOSFET, limiting the switching performance in the application. In other cases, there may be a desire

to minimize the effect of high-frequency switching noise by placing the high current driver physically close to the

load. Also, newer ICs that target the highest operating frequencies do not incorporate onboard gate drivers at all.

Their PWM outputs are only intended to drive the high impedance input to a driver such as the UCCx732x.

Finally, the control IC is under thermal stress due to power dissipation, and an external driver helps by moving

the heat from the controller to an external package.

9.2 Typical Application

Figure 12. LM5111 Driving Two Independent MOSFETs

9.2.1 Design Requirements

To select the proper device from the LM5111 family, TI recommends first checking the appropriate logic for the

outputs. LM5111 has dual inverting outputs; dual noninverting outputs; inverting channel A and noninverting

channel B. Refer to operating modes to select which driver from the family is required in a given application.

Moreover, some design considerations must be evaluated first in order to make the most appropriate selection.

Among these considerations are VCC and power dissipation.

110 100 1000

FREQUENCY (kHz)

0.1

100

SUPPLY CURRENT (mA)

VCC = 15V

VCC = 10V

VCC = 5V

TA = 25°C

CL = 2200pF

100

10k

CAPACITIVE LOAD (pF)

0.1

1000

SUPPLY CURRENT (mA)

f = 500kHz

f = 100kHz

f = 10kHz

TA = 25°C

VCC = 12V

LM5111

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

www.ti.com

Product Folder Links: LM5111

Typical Application (continued)

9.2.2 Detailed Design Procedure

9.2.2.1 VCC

Although quiescent VCC current is very low, total supply current will be higher, depending on OUTA and OUTB

current and the programmed oscillator frequency. Total VCC current is the sum of quiescent VCC current and the

average OUT current. Knowing the operating frequency and the MOSFET gate charge (Qg), average OUT

current can be calculated using Equation 1.

IOUT = Qg× f

where

• f is frequency (1)

For the best high-speed circuit performance, two VCC bypass capacitors are recommended to prevent noise

problems. The use of surface mount components is highly recommended. A 0.1-µF ceramic capacitor should be

located closest to the VDD to ground connection. In addition, a larger capacitor (such as 1 µF and above) with

relatively low ESR should be connected in parallel, to help deliver the high current peaks to the load. The parallel

combination of capacitors should present a low impedance characteristic for the expected current levels in the

driver application.

9.2.3 Application Curves

Figure 13. Supply Current vs Frequency Figure 14. Supply Current vs Capacitive Load

LM5111

www.ti.com

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

Product Folder Links: LM5111

10 Power Supply Recommendations

10.1 Bias Supply Voltage

The recommended bias supply voltage range for LM5111 is from 3.5 V to 14 V. The upper end of this range is

driven by the 15-V absolute maximum voltage rating of the VCC. TI recommends keeping proper margin to allow

for transient voltage spikes. A local bypass capacitor must be placed between the VCC and VEE pins, and this

capacitor must be placed as close to the device as possible. TI recommends a low ESR, ceramic surface mount

capacitor. TI recommends using 2 capacitors across VCC and VEE: a 100-nF ceramic surface-mount capacitor

for high frequency filtering placed very close to VCC and VEE pin, and another surface-mount capacitor, 220 nF

to 10 µF, for IC bias requirements.

11 Layout

11.1 Layout Guidelines

Attention must be given to board layout when using LM5111. Some important considerations include:

• A Low ESR/ESL capacitor must be connected close to the IC and between the VCC and VEE pins to support

high peak currents being drawn from VCC during turnon of the MOSFET.

• Proper grounding is crucial. The drivers need a very low impedance path for current return to ground avoiding

inductive loops. The two paths for returning current to ground are a) between LM5111 VEE pin and the ground

of the circuit that controls the driver inputs, b) between LM5111 VEE pin and the source of the power

MOSFET being driven. All these paths should be as short as possible to reduce inductance and be as wide

as possible to reduce resistance. All these ground paths should be kept distinctly separate to avoid coupling

between the high current output paths and the logic signals that drive the LM5111. A good method is to

dedicate one copper plane in a multi-layered PCB to provide a common ground surface.

• With the rise and fall times in the range of 10 ns to 30 ns, care is required to minimize the lengths of current

carrying conductors to reduce their inductance and EMI from the high di/dt transients generated by the

LM5111.

• The LM5111 footprint is compatible with other industry standard drivers including the TC4426/27/28 and

UCC27323/4/5.

• If either channel is not being used, the respective input pin (IN_A or IN_B) should be connected to either VEE

or VCC to avoid spurious output signals.

N/C

INA

VEE

INB OUTB

1: N/C

C2 (Bypass Capacitor)

N/C

2: INA

N/C

3: VEE

VEE

N/C

4: INB

Power Stage

Current

7: OUTA

6: VCC

5: OUTB

Output Loop of Driver

Bias

Loop

8: N/C

LM5111

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

www.ti.com

Product Folder Links: LM5111

11.2 Layout Example

Figure 15. Layout

11.3 Thermal Considerations

The primary goal of thermal management is to maintain the integrated circuit (IC) junction temperature (TJ) below

a specified maximum operating temperature to ensure reliability. It is essential to estimate the maximum TJof IC

components in worst case operating conditions. The junction temperature is estimated based on the power

dissipated in the IC and the junction to ambient thermal resistance θJA for the IC package in the application board

and environment. The θJA is not a given constant for the package and depends on the printed circuit board

design and the operating environment.

11.3.1 Drive Power Requirement Calculations in LM5111

The LM5111 dual low side MOSFET driver is capable of sourcing/sinking 3A/5A peak currents for short intervals

to drive a MOSFET without exceeding package power dissipation limits. High peak currents are required to

switch the MOSFET gate very quickly for operation at high frequencies.

VHIGH

VGATE

VTRIG CIN

LM5111

www.ti.com

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

Product Folder Links: LM5111

Thermal Considerations (continued)

Figure 16. Driver Output Stage and Load

The schematic above shows a conceptual diagram of the LM5111 output and MOSFET load. Q1 and Q2 are the

switches within the gate driver. RGis the gate resistance of the external MOSFET, and CIN is the equivalent gate

capacitance of the MOSFET. The gate resistance Rg is usually very small and losses in it can be neglected. The

equivalent gate capacitance is a difficult parameter to measure since it is the combination of CGS (gate to source

capacitance) and CGD (gate to drain capacitance). Both of these MOSFET capacitances are not constants and

vary with the gate and drain voltage. The better way of quantifying gate capacitance is the total gate charge QG

in coulombs. QGcombines the charge required by CGS and CGD for a given gate drive voltage VGATE.

Assuming negligible gate resistance, the total power dissipated in the MOSFET driver due to gate charge is

approximated by

PDRIVER = VGATE × QG× FSW

where

• FSW = switching frequency of the MOSFET (2)

For example, consider the MOSFET MTD6N15 whose gate charge specified as 30 nC for VGATE = 12 V.

The power dissipation in the driver due to charging and discharging of MOSFET gate capacitances at switching

frequency of 300 kHz and VGATE of 12 V is equal to

PDRIVER = 12 V × 30 nC × 300 kHz = 0.108 W. (3)

If both channels of the LM5111 are operating at equal frequency with equivalent loads, the total losses will be

twice as this value which is 0.216 W.

In addition to the above gate charge power dissipation, transient power is dissipated in the driver during output

transitions. When either output of the LM5111 changes state, current will flow from VCC to VEE for a very brief

interval of time through the output totem-pole N and P channel MOSFETs. The final component of power

dissipation in the driver is the power associated with the quiescent bias current consumed by the driver input

stage and Under-voltage lockout sections.

Characterization of the LM5111 provides accurate estimates of the transient and quiescent power dissipation

components. At 300-kHz switching frequency and 30-nC load used in the example, the transient power will be 8

mW. The 1-mA nominal quiescent current and 12-V VGATE supply produce a 12-mW typical quiescent power.

Therefore the total power dissipation

PD= 0.216 + 0.008 + 0.012 = 0.236 W. (4)

We know that the junction temperature is given by

TJ= PD×θJA + TA(5)

ISOURCE (MAX) := TJ(MAX) - TA

TJA · VDIODE

ISINK (MAX) := TJ(MAX) - TA

TJA · RDS (ON)

LM5111

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

www.ti.com

Product Folder Links: LM5111

Thermal Considerations (continued)

Or the rise in temperature is given by

TRISE = TJ−TA= PD×θJA (6)

For SOIC package, θJA is estimated as 170°C/W for the conditions of natural convection. For MSOP-PowerPAD,

θJA is typically 60°C/W.

Therefore for SOIC TRISE is equal to

TRISE = 0.236 × 170 = 40.1°C (7)

11.3.2 Continuous Current Rating of LM5111

The LM5111 can deliver pulsed source/sink currents of 3 A and 5 A to capacitive loads. In applications requiring

continuous load current (resistive or inductive loads), package power dissipation, limits the LM5111 current

capability far below the 5-A sink and 3-A source capability. Rated continuous current can be estimated both

when sourcing current to or sinking current from the load. For example when sinking, the maximum sink current

can be calculated as:

where

• RDS(on) is the on resistance of lower MOSFET in the output stage of LM5111 (8)

Consider TJ(max) of 125°C and θJA of 170°C/W for an SO-8 package under the condition of natural convection

and no air flow. If the ambient temperature (TA) is 60°C, and the RDS(on) of the LM5111 output at TJ(max) is 2.5

Ω, this equation yields ISINK(max) of 391 mA which is much smaller than 5-A peak pulsed currents.

Similarly, the maximum continuous source current can be calculated as

where

• VDIODE is the voltage drop across hybrid output stage which varies over temperature and can be assumed to

be about 1.1 V at TJ(max) of 125°C (9)

Assuming the same parameters as above, this equation yields ISOURCE(max) of 347 mA.

LM5111

www.ti.com

SNVS300H –JULY 2004–REVISED SEPTEMBER 2016

Product Folder Links: LM5111

12 Device and Documentation Support

12.1 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper

right corner, click on Alert me to register and receive a weekly digest of any product information that has

changed. For change details, review the revision history included in any revised document.

12.2 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective

contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of

Use.

TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration

among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help

solve problems with fellow engineers.

Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and

contact information for technical support.

12.3 Trademarks

E2E is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

12.4 Electrostatic Discharge Caution

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

12.5 Glossary

SLYZ022 —TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

13 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most

current data available for the designated devices. This data is subject to change without notice and revision of

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM

www.ti.com 6-Feb-2020

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LM5111-1M/NOPB ACTIVE SOIC D 8 95 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 5111

-1M

LM5111-1MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 5111

-1M

LM5111-1MY/NOPB ACTIVE HVSSOP DGN 8 1000 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM SJKB

LM5111-1MYX/NOPB ACTIVE HVSSOP DGN 8 3500 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM SJKB

LM5111-2M/NOPB ACTIVE SOIC D 8 95 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 5111

-2M

LM5111-2MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 5111

-2M

LM5111-2MY/NOPB ACTIVE HVSSOP DGN 8 1000 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM SJLB

LM5111-2MYX/NOPB ACTIVE HVSSOP DGN 8 3500 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM SJLB

LM5111-3MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 5111

-3M

LM5111-4M/NOPB ACTIVE SOIC D 8 95 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM 5111

-4M

LM5111-4MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM -40 to 125 5111

-4M

LM5111-4MY/NOPB ACTIVE HVSSOP DGN 8 1000 Green (RoHS

& no Sb/Br) SN Level-1-260C-UNLIM SSYB

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

PACKAGE OPTION ADDENDUM

www.ti.com 6-Feb-2020

Addendum-Page 2

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LM5111-1MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LM5111-1MY/NOPB HVSSOP DGN 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

LM5111-1MYX/NOPB HVSSOP DGN 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

LM5111-2MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LM5111-2MY/NOPB HVSSOP DGN 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

LM5111-2MYX/NOPB HVSSOP DGN 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

LM5111-3MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LM5111-4MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

LM5111-4MY/NOPB HVSSOP DGN 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 6-Sep-2019

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LM5111-1MX/NOPB SOIC D 8 2500 367.0 367.0 35.0

LM5111-1MY/NOPB HVSSOP DGN 8 1000 210.0 185.0 35.0

LM5111-1MYX/NOPB HVSSOP DGN 8 3500 367.0 367.0 35.0

LM5111-2MX/NOPB SOIC D 8 2500 367.0 367.0 35.0

LM5111-2MY/NOPB HVSSOP DGN 8 1000 210.0 185.0 35.0

LM5111-2MYX/NOPB HVSSOP DGN 8 3500 367.0 367.0 35.0

LM5111-3MX/NOPB SOIC D 8 2500 367.0 367.0 35.0

LM5111-4MX/NOPB SOIC D 8 2500 367.0 367.0 35.0

LM5111-4MY/NOPB HVSSOP DGN 8 1000 210.0 185.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 6-Sep-2019

Pack Materials-Page 2

www.ti.com

PACKAGE OUTLINE

6X 0.65

1.95

8X 0.38

0.25

5.05

4.75 TYP

SEATING

PLANE

0.15

0.05

0.25

GAGE PLANE

0 -8

1.1 MAX

0.23

0.13

1.88

1.58

2.0

1.7

B3.1

2.9

NOTE 4

3.1

2.9

NOTE 3

0.7

0.4

PowerPAD VSSOP - 1.1 mm max heightDGN0008A

SMALL OUTLINE PACKAGE

4218836/A 11/2019

0.13 C A B

PIN 1 INDEX AREA

SEE DETAIL A

0.1 C

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing

per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not

exceed 0.15 mm per side.

4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.

5. Reference JEDEC registration MO-187.

PowerPAD is a trademark of Texas Instruments.

A 20

DETAIL A

TYPICAL

SCALE 4.000

EXPOSED THERMAL PAD

www.ti.com

EXAMPLE BOARD LAYOUT

0.05 MAX

ALL AROUND 0.05 MIN

ALL AROUND

8X (1.4)

8X (0.45)

6X (0.65)

(4.4)

(R0.05) TYP

(2)

NOTE 9

(3)

NOTE 9

(1.22)

(0.55)

( 0.2) TYP

VIA

(1.88)

(2)

PowerPAD VSSOP - 1.1 mm max heightDGN0008A

SMALL OUTLINE PACKAGE

4218836/A 11/2019

NOTES: (continued)

6. Publication IPC-7351 may have alternate designs.

7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

8. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown

on this view. It is recommended that vias under paste be filled, plugged or tented.

9. Size of metal pad may vary due to creepage requirement.

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN

SCALE: 15X

SYMM

SOLDER MASK

DEFINED PAD

METAL COVERED

BY SOLDER MASK

SEE DETAILS

15.000

METAL

SOLDER MASK

OPENING METAL UNDER

SOLDER MASK SOLDER MASK

OPENING

EXPOSED METAL

SOLDER MASK DETAILS

NON-SOLDER MASK

DEFINED

(PREFERRED)

SOLDER MASK

DEFINED

www.ti.com

EXAMPLE STENCIL DESIGN

8X (1.4)

8X (0.45)

6X (0.65)

(4.4)

(R0.05) TYP

(1.88)

BASED ON

0.125 THICK

STENCIL

(2)

BASED ON

0.125 THICK

STENCIL

PowerPAD VSSOP - 1.1 mm max heightDGN0008A

SMALL OUTLINE PACKAGE

4218836/A 11/2019

1.59 X 1.690.175 1.72 X 1.830.15 1.88 X 2.00 (SHOWN)0.125 2.10 X 2.240.1

SOLDER STENCIL

OPENING

STENCIL

THICKNESS

NOTES: (continued)

10. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

11. Board assembly site may have different recommendations for stencil design.

SOLDER PASTE EXAMPLE

EXPOSED PAD 9:

100% PRINTED SOLDER COVERAGE BY AREA

SCALE: 15X

SYMM

METAL COVERED

BY SOLDER MASK SEE TABLE FOR

DIFFERENT OPENINGS

FOR OTHER STENCIL

THICKNESSES

www.ti.com

PACKAGE OUTLINE

.228-.244 TYP

[5.80-6.19]

.069 MAX

[1.75]

6X .050

[1.27]

8X .012-.020

[0.31-0.51]

.150

[3.81]

.005-.010 TYP

[0.13-0.25]

0 - 8 .004-.010

[0.11-0.25]

.010

[0.25]

.016-.050

[0.41-1.27]

4X (0 -15 )

.189-.197

[4.81-5.00]

NOTE 3

B .150-.157

[3.81-3.98]

NOTE 4

4X (0 -15 )

(.041)

[1.04]

SOIC - 1.75 mm max heightD0008A

SMALL OUTLINE INTEGRATED CIRCUIT

4214825/C 02/2019

NOTES:

1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.

Dimensioning and tolerancing per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not

exceed .006 [0.15] per side.

4. This dimension does not include interlead flash.

5. Reference JEDEC registration MS-012, variation AA.

.010 [0.25] C A B

PIN 1 ID AREA

SEATING PLANE

.004 [0.1] C

SEE DETAIL A

DETAIL A

TYPICAL

SCALE 2.800

www.ti.com

EXAMPLE BOARD LAYOUT

.0028 MAX

[0.07]

ALL AROUND

.0028 MIN

[0.07]

ALL AROUND

(.213)

[5.4]

6X (.050 )

[1.27]

8X (.061 )

[1.55]

8X (.024)

[0.6]

(R.002 ) TYP

[0.05]

SOIC - 1.75 mm max heightD0008A

SMALL OUTLINE INTEGRATED CIRCUIT

4214825/C 02/2019

NOTES: (continued)

6. Publication IPC-7351 may have alternate designs.

7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

METAL SOLDER MASK

OPENING

NON SOLDER MASK

DEFINED

SOLDER MASK DETAILS

EXPOSED

METAL

OPENING

SOLDER MASK METAL UNDER

SOLDER MASK

DEFINED

EXPOSED

METAL

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN

SCALE:8X

SYMM

SEE

DETAILS

SYMM

www.ti.com

EXAMPLE STENCIL DESIGN

8X (.061 )

[1.55]

8X (.024)

[0.6]

6X (.050 )

[1.27] (.213)

[5.4]

(R.002 ) TYP

[0.05]

SOIC - 1.75 mm max heightD0008A

SMALL OUTLINE INTEGRATED CIRCUIT

4214825/C 02/2019

NOTES: (continued)

8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

9. Board assembly site may have different recommendations for stencil design.

SOLDER PASTE EXAMPLE

BASED ON .005 INCH [0.125 MM] THICK STENCIL

SCALE:8X

SYMM

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE

DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”

AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD

PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate

TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable

standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you

permission to use these resources only for development of an application that uses the TI products described in the resource. Other

reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third

party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,

damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on

ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable

warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265