TPC8051-H TOSHIBA Field Effect Transistor Silicon N-Channel MOS Type (U-MOS-H) TPC8051-H Switching Regulator Applications Motor Drive Applications DC-DC Converter Applications Unit: mm * Small footprint due to a small and thin package * High-speed switching * Small gate charge: QSW = 16 nC (typ.) * Low drain-source ON-resistance: RDS (ON) = 6.3 m (typ.) * High forward transfer admittance: |Yfs| = 45 S (typ.) * Low leakage current: IDSS = 10 A (max) (VDS = 80 V) * Enhancement mode: Vth = 1.3 to 2.3 V (VDS = 10 V, ID = 1.0 mA) Absolute Maximum Ratings (Ta = 25C) Characteristic Symbol Rating Unit Drain-source voltage VDSS 80 V Drain-gate voltage (RGS = 20 k) VDGR 80 V Gate-source voltage VGSS 20 V (Note 1) ID 13 Pulsed (Note 1) IDP 52 Drain power dissipation (t = 10 s) (Note 2a) PD 1.9 W Drain power dissipation (t = 10 s) (Note 2b) PD 1.0 W Single-pulse avalanche energy (Note 3) EAS 110 mJ Avalanche current IAR 13 A Repetitive avalanche energy (Tc=25) (Note 4) EAR 0.06 mJ Channel temperature Tch 150 C Storage temperature range Tstg -55 to 150 C Drain current DC A JEDEC JEITA TOSHIBA 2-6J1B Weight: 0.085g (typ.) Circuit Configuration 8 7 6 5 Note: For Notes 1 to 4, refer to the next page. 4 1 2 3 Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). This transistor is an electrostatic-sensitive device. Handle with care. 1 http://store.iiic.cc/ 2009-06-19 TPC8051-H Thermal Characteristics Characteristic Thermal resistance, channel to ambient (t = 10 s) (Note 2a) Thermal resistance, channel to ambient (t = 10 s) (Note 2b) Symbol Max Unit Rth (ch-a) 65.8 C/W Rth (ch-a) 125 C/W Marking (Note 5) TPC8051 H Part No. (or abbreviation code) Lot No. Note Note : A line under a Lot No. identifies the indication of product Labels [[G]]/RoHS COMPATIBLE or [[G]]/RoHS [[Pb]] Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. The RoHS is Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. Note 1: Ensure that the channel temperature does not exceed 150C. Note 2: (a) Device mounted on a glass-epoxy board (a) (b) Device mounted on a glass-epoxy board (b) FR-4 25.4 x 25.4 x 0.8 (Unit: mm) FR-4 25.4 x 25.4 x 0.8 (Unit: mm) (b) (a) Note 3: VDD = 24 V, Tch = 25C (initial), L = 1 mH, RG = 25 , IAR = 13 A Note 4: Repetitive rating: pulse width limited by maximum channel temperature Note 5: * Weekly code: (Three digits) Week of manufacture (01 for the first week of the year, continuing up to 52 or 53) Year of manufacture (The last digit of the year) 2 http://store.iiic.cc/ 2009-06-19 TPC8051-H Electrical Characteristics (Ta = 25C) Characteristic Symbol Test Condition Min Typ. Max Unit Gate leakage current IGSS VGS = 20 V, VDS = 0 V 100 nA Drain cutoff current IDSS VDS = 80 V, VGS = 0 V 10 A V (BR) DSS ID = 10 mA, VGS = 0 V 80 V (BR) DSX ID = 10 mA, VGS = -20 V 60 Vth VDS = 10 V, ID = 1.0 mA 1.3 2.3 VGS = 4.5 V, ID = 6.5 A 6.7 10.1 VGS = 10 V, ID = 6.5 A 6.3 9.7 VDS = 10 V, ID = 6.5 A 22.5 45 5800 7540 150 210 520 1.0 1.5 3.4 14 6.7 67 VDD 64 V, VGS = 10 V, ID = 13 A 85 VDD 64 V, VGS = 5 V, ID = 13 A 43 14 10 16 Drain-source breakdown voltage Gate threshold voltage Drain-source ON-resistance RDS (ON) Forward transfer admittance |Yfs| Input capacitance Ciss Reverse transfer capacitance Crss Output capacitance Coss Gate resistance VDS = 10 V, VGS = 0 V, f = 1 MHz VDS = 10 V, VGS = 0 V, f = 1 MHz rg tr VGS Turn-on time ton Fall time tf Turn-off time VDD 40 V toff Total gate charge (gate-source plus gate-drain) Duty 1%, tw = 10 s Qg Gate-source charge 1 Qgs1 Gate-drain ("Miller") charge Qgd Gate switch charge QSW 0V 4.7 Switching time ID = 6.5 A VOUT 10 V RL = 6.2 Rise time VDD 64 V, VGS = 10 V, ID = 13 A V V m S pF ns nC Source-Drain Ratings and Characteristics (Ta = 25C) Characteristic Peak forward current Forward voltage (diode) Pulse (Note 1) Symbol Test Condition Min Typ. Max Unit IFP 52 A -1.2 V VDSF IDR = 13 A, VGS = 0 V 3 http://store.iiic.cc/ 2009-06-19 TPC8051-H 4.5 3.2 3 4.5 3.4 3.1 ID - VDS 20 Common source Ta = 25C Pulse test 2.7 2.9 Common source Ta = 25C Pulse test 30 ID 2.6 12 Drain current ID Drain current 2.8 3 (A) 16 2.9 10 (A) 2.8 10 ID - VDS 40 8 2.5 4 2.7 20 2.6 10 VGS = 2.5 V VGS = 2.4 V 0 0 0.2 0.4 0.6 Drain-source voltage 0.8 VDS 0 0 1 (V) 0.8 0.4 ID - VGS VDS 2 (V) VDS - VGS Common source VDS = 10 V 25 Pulse test (V) 20 VDS 0.2 Drain-source voltage (A) ID Drain current 1.6 Drain-source voltage 30 15 Ta = -55C 10 100 25 5 0 0 1.2 1 2 3 Gate-source voltage 4 VGS 0.16 0.12 ID = 13 A 0.08 6.5 0.04 3.3 0 0 5 Common source Ta = 25 Pulse test (V) 2 4 6 Gate-source voltage 8 VGS 10 (V) 100 Common source VDS = 10 V Pulse test Drain-source ON-resistance RDS (ON) (m) Forward transfer admittance |Yfs| (S) RDS (ON) - ID 1000 100 Ta = -55C 25 10 100 1 0.1 0.1 1 Drain current 10 ID 10 4.5 VGS = 10 V 1 0.1 100 Common source Ta = 25 Pulse test Drain current (A) 4 http://store.iiic.cc/ 10 1 ID 100 (A) 2009-06-19 TPC8051-H RDS (ON) - Ta IDR - VDS 100 (A) Common source Pulse test IDR 12 ID = 3.3, 6.5, 13 A Drain reverse current 8 ID = 3.3, 6.5, 13 A VGS = 4.5 V 4 VGS = 10 V 0 -80 -40 0 40 Ambient temperature 80 120 Ta 10 3 10 1 Common source Ta = 25C Pulse test -0.2 (C) -0.4 Capacitance - VDS Vth (V) Gate threshold voltage (V) Coss 100 Crss Common source VGS = 0 V f = 1 MHz Ta = 25C 1 10 80 120 Drain-source voltage 1 0.5 Common source VDS = 10 V ID = 1 mA Pulse test 0 -80 100 VDS 1.5 -40 PD (2) 0.8 0.4 80 Ambient temperature 120 Ta 20 80 16 (V) Drain-source voltage 1.2 40 (C) 100 VDS (1) Ta 160 Dynamic input/output characteristics (1) Device mounted on a glass-epoxy board (a) (Note 2a) (2) Device mounted on a glass-epoxy board (b) (Note 2b) t=10s 1.6 40 Ambient temperature (V) PD - Ta 2 0 VDS = 64 V 60 (C) 32 VDD = 64 V 32 VGS 20 16 0 0 160 12 16 40 40 80 Total gate charge 5 http://store.iiic.cc/ (V) 10 0.1 2 VGS (pF) C Capacitance VDS -1.2 Vth - Ta 1000 (W) -1.0 -0.8 2.5 Ciss Drain power dissipation -0.6 Drain-source voltage 10000 0 0 VGS = 0 V 1 0.1 0 160 4.5 2 8 Common source ID = 13 A Ta = 25C 4 Pulse test 120 Qg Gate-source voltage Drain-source ON-resistance RDS (ON) (m) 16 0 160 (nC) 2009-06-19 TPC8051-H rth - tw Transient thermal impedance rth (C/W) 1000 (1) Device mounted on a glass-epoxy board (a) (Note 2a) (2) Device mounted on a glass-epoxy board (b) (Note 2b) (2) 100 (1) 10 1 Single - pulse 0.1 0.001 0.01 0.1 1 Pulse width 10 tw 100 1000 (s) Safe operating area 100 I max (Pulse) * D t = 1ms * Drain current ID (A) 1000 10 10ms * 1 0.1 * Single - pulse Ta = 25 Curves must be derated linearly with increase in temperature. 0.01 0.1 VDSS max 1 Drain-source voltage 10 VDS 100 (V) 6 http://store.iiic.cc/ 2009-06-19 TPC8051-H RESTRICTIONS ON PRODUCT USE * Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application that Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact ("Unintended Use"). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 7 http://store.iiic.cc/ 2009-06-19