AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER AS5045 12 BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 1 General Description 1.2 DATA SHEET Key Features The AS5045 is a contactless magnetic rotary encoder for accurate angular measurement over a full turn of 360. It is a system-on-chip, combining integrated Hall elements, analog front end and digital signal processing in a single device. - Contactless high resolution rotational position encoding over a full turn of 360 degrees - Two digital 12bit absolute outputs: - Serial interface and - Pulse width modulated (PWM) output To measure the angle, only a simple two-pole magnet, rotating over the center of the chip, is required. The magnet may be placed above or below the IC. - User programmable zero position - Failure detection mode for magnet placement monitoring and loss of power supply - "red-yellow-green" indicators display placement of magnet in Z-axis - Serial read-out of multiple interconnected AS5045 devices using Daisy Chain mode - Tolerant to magnet misalignment and airgap variations - Wide temperature range: - 40C to + 125C - Small Pb-free package: SSOP 16 (5.3mm x 6.2mm) The absolute angle measurement provides instant indication of the magnet's angular position with a resolution of 0.0879 = 4096 positions per revolution. This digital data is available as a serial bit stream and as a PWM signal. An internal voltage regulator allows the AS5045 to operate at either 3.3 V or 5 V supplies 1.3 Applications - Industrial applications: - Contactless rotary position sensing - Robotics - Automotive applications: - Steering wheel position sensing - Transmission gearbox encoder - Headlight position control - Torque sensing - Valve position sensing - Replacement of high end potentiometers Figure 1: Typical arrangement of AS5045 and magnet 1.1 Benefits - Complete system-on-chip - Flexible system solution provides absolute and PWM outputs simultaneously - Ideal for applications in harsh environments due to contactless position sensing - No calibration required Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 1 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 2 Pin Configuration 1 16 VDD5V MagDECn 2 15 VDD3V3 NC 3 NC 4 NC 5 Mode 6 VSS Prog_DI AS5045 MagINCn 14 NC 13 NC 12 PWM 11 CSn 7 10 CLK 8 9 DO Pin Symbol Type Description 11 CSn DI_PU, ST Chip Select, active low; SchmittTrigger input, internal pull-up resistor (~50k) 12 PWM DO Pulse Width Modulation of approx. 244Hz; 1s/step (opt. 122Hz; 2s/step) 13 NC - Must be left unconnected 14 NC - Must be left unconnected S 3V-Regulator Output, internally regulated from VDD5V. Connect to VDD5V for 3V supply voltage. Do not load externally. S Positive Supply Voltage, 3.0 to 5.5 V 15 VDD3V3 16 VDD5V Table 1: Pin description SSOP16 Figure 2: Pin configuration SSOP16 2.1 Pin Description Table 1 shows the description of each pin of the standard SSOP16 package (Shrink Small Outline Package, 16 leads, body size: 5.3mm x 6.2mmm; see Figure 2). Pins 7, 15 and 16 are supply pins, pins 3, 4, 5, 6, 13 and 14 are for internal use and must not be connected. Pins 1 and 2 are the magnetic field change indicators, MagINCn and MagDECn (magnetic field strength increase or decrease through variation of the distance between the magnet and the device). These outputs can be used to detect the valid magnetic field range. Furthermore those indicators can also be used for contact-less push-button functionality. Pin 6 Mode allows switching between filtered (slow) and unfiltered (fast mode). See section 4. Pin Symbol Type Description 1 MagINCn DO_OD Magnet Field Magnitude INCrease; active low, indicates a distance reduction between the magnet and the device surface. See Table 5 2 MagDECn DO_OD Magnet Field Magnitude DECrease; active low, indicates a distance increase between the device and the magnet. See Table 5 3 NC - Must be left unconnected 4 NC - Must be left unconnected 5 NC - Must be left unconnected 6 Mode - Select between slow (open, low: VSS) and fast (high) mode. Internal pull-down resistor. 7 VSS S Negative Supply Voltage (GND) 8 Prog_DI DI_PD OTP Programming Input and Data Input for Daisy Chain mode. Internal pull-down resistor (~74k). Connect to VSS if not used 9 DO DO_T Data Output of Synchronous Serial Interface 10 CLK DI, ST Clock Input of Synchronous Serial Interface; Schmitt-Trigger input Revision 1.2, 03-Oct-06 DO_OD DO DI_PD DI_PU digital digital digital digital output open drain output input pull-down input pull-up S DI DO_T ST supply pin digital input digital output /tri-state Schmitt-Trigger input Pin 8 (Prog) is used to program the zero-position into the OTP (see chapter 7.1). This pin is also used as digital input to shift serial data through the device in Daisy Chain configuration, (see page 6). Pin 11 Chip Select (CSn; active low) selects a device within a network of AS5045 encoders and initiates serial data transfer. A logic high at CSn puts the data output pin (DO) to tri-state and terminates serial data transfer. This pin is also used for alignment mode (Figure 13) and programming mode (Figure 9). Pin 12 allows a single wire output of the 10-bit absolute position value. The value is encoded into a pulse width modulated signal with 1s pulse width per step (1s to 4096s over a full turn). By using an external low pass filter, the digital PWM signal is converted into an analog voltage, making a direct replacement of potentiometers possible. 3 Functional Description The AS5045 is manufactured in a CMOS standard process and uses a spinning current Hall technology for sensing the magnetic field distribution across the surface of the chip. The integrated Hall elements are placed around the center of the device and deliver a voltage representation of the magnetic field at the surface of the IC. Through Sigma-Delta Analog / Digital Conversion and Digital Signal-Processing (DSP) algorithms, the AS5045 provides accurate high-resolution absolute angular position information. For this purpose a Coordinate www.austriamicrosystems.com Page 2 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER Rotation Digital Computer (CORDIC) calculates the angle and the magnitude of the Hall array signals. The DSP is also used to provide digital information at the outputs M a g I N C n and M a g D E C n that indicate movements of the used magnet towards or away from the device's surface. A small low cost diametrically magnetized (two-pole) standard magnet provides the angular position information (see Figure 16). The AS5045 senses the orientation of the magnetic field and calculates a 12-bit binary code. This code can be accessed via a Synchronous Serial Interface (SSI). In addition, an absolute angular representation is given by a Pulse Width Modulated signal at pin 12 (PWM). This PWM signal output also allows the generation of a direct proportional analogue voltage, by using an external LowPass-Filter. The AS5045 is tolerant to magnet misalignment and magnetic stray fields due to differential measurement technique and Hall sensor conditioning circuitry. Figure 3: AS5045 block diagram 4 Mode Input Pin The mode input pin activates or deactivates an internal filter, that is used to reduce the analog output noise. Activating the filter (Mode pin = LOW or open) provides a reduced output noise of 0.03 rms. At the same time, the output delay is increased to 384s. This mode is recommended for high precision, low speed applications. Deactivating the filter (Mode pin = HIGH) reduces the output delay to 96s and provides an output noise of 0.06 rms. This mode is recommended for higher speed applications. Switching the Mode pin affects the following parameters: Parameter slow mode (Mode = low or open) fast mode (Mode = high, VDD5V) sampling rate 2.61 kHz (384 s) 10.42 kHz (96s) transition noise (1 sigma) 0.03 rms 0.06 rms output delay 384s 96s max. speed @ 4096 samples/rev. 38 rpm 153 rpm max. speed @ 1024 samples/rev. 153 rpm 610 rpm max. speed @ 256 samples/rev. 610 rpm 2441 rpm max. speed @ 64 samples/rev. 2441 rpm 9766 rpm Table 2: Slow and fast mode parameters Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 3 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 12-bit Absolute Angular Position Output 4.1 Synchronous Serial Interface (SSI) tCLK FE CSn TCLK/2 tCLK FE tCSn 1 CLK DO 8 D11 tDO active D10 D9 D8 D7 D6 D5 D4 18 D3 D2 D1 D0 OCF COF LIN Mag INC tDO valid Angular Position Data Status Bits Mag DEC 1 Even PAR D11 tDO Tristate Figure 4: Synchronous serial interface with absolute angular position data If CSn changes to logic low, Data Out (DO) will change from high impedance (tri-state) to logic high and the read-out will be initiated. After a minimum time t CLK FE, data is latched into the output shift register with the first falling edge of CLK. Each subsequent rising CLK edge shifts out one bit of data. The serial word contains 18 bits, the first 12 bits are the angular information D[11:0], the subsequent 6 bits contain system information, about the validity of data such as OCF, COF, LIN, Parity and Magnetic Field status (increase/decrease) . A subsequent measurement is initiated by a "high" pulse at CSn with a minimum duration of t CSn. 4.1.1 Data Content D11:D0 absolute angular position data (MSB is clocked out first) OCF (Offset Compensation Finished), logic high indicates the finished Offset Compensation Algorithm COF (Cordic Overflow), logic high indicates an out of range error in the CORDIC part. When this bit is set, the data at D9:D0 is invalid. The absolute output maintains the last valid angular value. This alarm may be resolved by bringing the magnet within the X-Y-Z tolerance limits. LIN (Linearity Alarm), logic high indicates that the input field generates a critical output linearity. When this bit is set, the data at D9:D0 may still be used, but can contain invalid data. This warning may be resolved by bringing the magnet within the X-Y-Z tolerance limits. Even Parity bit for transmission error detection of bits 1...17 (D11...D0, OCF, COF, LIN, MagINC, MagDEC) Placing the magnet above the chip, angular values increase in clockwise direction by default. Data D11:D0 is valid, when the status bits have the following configurations: OCF 1 COF 0 LIN 0 Mag INC Mag DEC 0 0 0 1 1 0 1*) 1*) Parity even checksum of bits 1:15 Table 3: Status bit outputs *) MagInc=MagDec=1 is only recommended in YELLOW mode (see Table 5) Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 4 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 4.1.2 Z-axis Range Indication (Push Button Feature, Red/Yellow/Green Indicator) The AS5045 provides several options of detecting movement and distance of the magnet in the Z-direction. Signal indicators MagINCn and MagDECn are available both as hardware pins (pins #1 and 2) and as status bits in the serial data stream (see Figure 4). Additionally, an OTP programming option is available with bit MagCompEn (see Figure 9) that enables additional features: In the default state, the status bits MagINC, MagDec and pins MagINCn, MagDECn have the following function: Status bits Hardware pins OTP: Mag CompEn = 0 (default) Mag DEC Mag INCn Description 0 0 Off Off No distance change Magnetic input field OK (in range, ~45...75mT) 0 1 Off On Distance increase; pull-function. This state is dynamic and only active while the magnet is moving away from the chip. 1 0 On Off Distance decrease; push- function. This state is dynamic and only active while the magnet is moving towards the chip. 1 1 On On Magnetic input field invalid - out of recommended range: too large, too small (missing magnet) Mag INC Mag DECn Table 4: Magnetic field strength variation indicator When bit MagCompEn is programmed in the OTP, the function of status bits MagINC, MagDec and pins MagINCn, MagDECn is changed to the following function: Status bits Hardware pins Mag INC Mag DEC LIN 0 0 1 1 Mag OTP: Mag CompEn = 1 (red-yellow-green programming option) INCn Mag DECn 0 Off Off No distance change Magnetic input field OK ( GREEN range, ~45...75mT) 1 0 On Off YELLOW range: magnetic field is ~ 25...45mT or ~75...135mT. The AS5045 may still be operated in this range, but with slightly reduced accuracy. 1 1 On On RED range: magnetic field is ~<25mT or >~135mT. It is still possible to operate the AS5045 in the red range, but not recommended. All other combinations n/a n/a Not available Description Table 5: Magnetic field strength red-yellow-green indicator (OTP option) Note: Pin 1 (MagINCn) and pin 2 (MagDECn) are active low via open drain output and require an external pull-up resistor. If the magnetic field is in range, both outputs are turned off. The two pins may also be combined with a single pull-up resistor. In this case, the signal is high when the magnetic field is in range. It is low in all other cases (see Table 4 and Table 5). Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 5 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 4.2 Daisy Chain Mode The Daisy Chain mode allows connection of several AS5045's in series, while still keeping just one digital input for data transfer (see "Data IN" in Figure 5 below). This mode is accomplished by connecting the data output (DO; pin 9) to the data input (PROG; pin 8) of the subsequent device. The serial data of all connected devices is read from the DO pin of the first device in the chain. The length of the serial bit stream increases with every connected device, it is n * (18+1) bits: e.g. 38 bit for two devices, 57 bit for three devices, etc... The last data bit of the first device (Parity) is followed by a dummy bit and the first data bit of the second device (D11), etc... (see Figure 6) AS5045 1st Device C Data IN DO AS5045 2nd Device Prog CSn DO CLK AS5045 last Device Prog CSn CLK DO Prog CSn CLK CLK CSn Figure 5: Daisy Chain hardware configuration CSn TCLK/2 tCLK FE 1 CLK DO 8 D11 tDO active D10 D9 D8 D7 D6 D5 D4 18 D3 D2 D1 D0 OCF COF LIN Mag INC Mag Even DEC PAR D 1 2 3 D11 D10 D9 tDO valid Angular Position Data Status Bits st 1 Device Angular Position Data 2nd Device Figure 6: Daisy Chain mode data transfer Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 6 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 5 Pulse Width Modulation (PWM) Output When PWMhalfEN = 1, the PWM timing is as shown in Table 7: The AS5045 provides a pulse width modulated output (PWM), whose duty cycle is proportional to the measured angle: Position = ton 4097 (ton + toff ) - 1 The PWM frequency is internally trimmed to an accuracy of 5% (10% over full temperature range). This tolerance can be cancelled by measuring the complete duty cycle as shown above. Angle PW MIN Parameter Symbol Typ Unit Note PWM frequency fPWM 122 Hz Signal period: 4097s MIN pulse width PWMIN 2 s - Position 0d - Angle 0 deg MAX pulse width PWMAX 8192 s - Position 4095d - Angle 359,91 deg Table 7: PWM signal parameters with half frequency (OTP option) 6 Analog Output An analog output can be generated by averaging the PWM signal, using an external active or passive lowpass filter. The analog output voltage is proportional to the angle: 0= 0V; 360 = VDD5V. 0 deg (Pos 0) 1s 4097s PW MAX 359.91 deg (Pos 4095) Using this method, the AS5045 can be used as direct replacement of potentiometers. 4096s R2 R1 Pin12 PWM C1 1/fPWM Figure 7: PWM output signal analog out C2 VDD 0V Pin7 360 0 VSS 5.1 Changing the PWM Frequency The PWM frequency of the AS5045 can be divided by two by setting a bit (PWMhalfEN) in the OTP register (see chapter 7). With PWMhalfEN = 0 the PWM timing is as shown in Table 6: Parameter Symbol Typ Unit Note PWM frequency fPWM 244 Hz Signal period: 4097s MIN pulse width PWMIN 1 s - Position 0d - Angle 0 deg MAX pulse width PWMAX 4096 s - Position 4095d - Angle 359,91 deg Figure 8: Simple 2 n d order passive RC lowpass filter Figure 8 shows an example of a simple passive lowpass filter to generate the analog output. R1,R2 4k7 C1,C2 1F / 6V R1 should be 4k7 to avoid loading of the PWM output. Larger values of Rx and Cx will provide better filtering and less ripple, but will also slow down the response time. Table 6: PWM signal parameters (default mode) Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 7 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 7 Programming the AS5045 After power-on, programming the AS5045 is enabled with the rising edge of CSn and Prog = logic high. 16 bit configuration data must be serially shifted into the OTP register via the Prog pin. The first "CCW" bit is followed by the zero position data (MSB first) and the Mode setting bits. Data must be valid at the rising edge of CLK (see Figure 9). After writing the data into the OTP register it can be permanently programmed by rising the Prog pin to the programming voltage V PROG . 16 CLK pulses (t PROG ) must be applied to program the fuses (Figure 10). To exit the programming mode, the chip must be reset by a poweron-reset. The programmed data is available after the next power-up. Note: During the programming process, the transitions in the programming current may cause high voltage spikes generated by the inductance of the connection cable. To avoid these spikes and possible damage to the IC, the connection wires, especially the signals Prog and VSS must be kept as short as possible. The maximum wire length between the V PROG switching transistor and pin Prog should not exceed 50mm (2 inches). To suppress eventual voltage spikes, a 10nF ceramic capacitor should be connected close to pins VPROG and VSS. This capacitor is only required for programming, it is not required for normal operation. The clock timing t clk must be selected at a proper rate to ensure that the signal Prog is stable at the rising edge of CLK (see Figure 9). Additionally, the programming supply voltage should be buffered with a 10F capacitor mounted close to the switching transistor. This capacitor aids in providing peak currents during programming. The specified programming voltage at pin Prog is 7.3 - 7.5V (see section 15.2). To compensate for the voltage drop across the V PROG switching transistor, the applied programming voltage may be set slightly higher (7.5 - 8.0V, see Figure 11). OTP Register Contents: CCW Counter Clockwise Bit ccw=0 - angular value increases in clockwise direction ccw=1 - angular value increases in counterclockwise direction Z [11:0]: Programmable Zero Position PWM dis: Disable PWM output MagCompEn: when set, activates LIN alarm both when magnetic field is too high and too low (see Table 5). PWMhalfEn: Revision 1.2, 03-Oct-06 7.1 Zero Position Programming Zero position programming is an OTP option that simplifies assembly of a system, as the magnet does not need to be manually adjusted to the mechanical zero position. Once the assembly is completed, the mechanical and electrical zero positions can be matched by software. Any position within a full turn can be defined as the permanent new zero position. For zero position programming, the magnet is turned to the mechanical zero position (e.g. the "off"-position of a rotary switch) and the actual angular value is read. This value is written into the OTP register bits Z11:Z0 (see Figure 9) and programmed as described in section 7. Note: The zero position value may also be modified before programming, e.g. to program an electrical zero position that is 180 (half turn) from the mechanical zero position, just add 2048 to the value read at the mechanical zero position and program the new value into the OTP register. 7.2 Repeated OTP Programming Although a single AS5045 OTP register bit can be programmed only once (from 0 to 1), it is possible to program other, unprogrammed bits in subsequent programming cycles. However, a bit that has already been programmed should not be programmed twice. Therefore it is recommended that bits that are already programmed are set to "0" during a programming cycle. 7.3 Non-permanent Programming It is also possible to re-configure the AS5045 in a nonpermanent way by overwriting the OTP register. This procedure is essentially a "Write Data" sequence (see Figure 9) without a subsequent OTP programming cycle. The "Write Data" sequence may be applied at any time during normal operation. This configuration remains set while the power supply voltage is above the power-on reset level (see 14.6). See Application Note AN5000-20 for further information. when set, PWM frequency is 122Hz or 2s / step (when PWMhalfEN = 0, PWM frequency is 244Hz, 1s / step) www.austriamicrosystems.com Page 8 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER CSn t D atain P rog CCW Z11 Z 10 Z9 Z8 Z7 Z6 Z5 1 C L K PROG t P rog enab le Z4 Z3 Z2 Z1 Z0 M ag C om p EN PW M dis 8 16 t clk se e te xt t D atain va lid PW M half EN P W M a nd status b it m o de s Z e ro P ositio n Figure 9: Programming access - write data (section of Figure 10) Write Data Programming Mode Power Off CSn 7.5V VDD VProgOff 0V Data Prog 1 16 CLKPROG tPrgH tPrgR tPROG tLoad PROG tPROG finished Figure 10: Complete programming sequence AS5045 Demoboard 1 MagINCn VDD5V 16 2 MagDECn 3 VDD3V3 15 6 7 7 6 5 4 3 2 1 NC 13 NC PWM Mode CSn VSS CLK 8 Prog_DI 10n 3V3 NC 14 NC 4 NC 5 DO AS5045 USB For programming, keep these 6 wires as short as possible! max. length = 2 inches (5cm) IC1 12 11 10 9 + 1F 22k *see Text PROG CSN DO CLK 5VUSB VDD3V3 VSS C GND connect to USB interface on PC 3 VPROG 2 + 1 10F VSS GND 7.5 ... 8.0V only required for OTP programming Cap only required for OTP programming Figure 11: OTP programming connection of AS5045 (shown with AS5045 demoboard) Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 9 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 7.4 Analog Readback Mode The following falling slope of CSn changes pin PROG to an analog output, providing a reference voltage V ref , that must be saved as a reference for the calculation of the subsequent programmed and unprogrammed OTP bits. Following this step, each rising slope of CLK outputs one bit of data in the reverse order as during programming (see Figure 9: Md0-MD1-Div0,Div1-Indx-Z0...Z11, ccw). Non-volatile programming (OTP) uses on-chip zener diodes, which become permanently low resistive when subjected to a specified reverse current. The quality of the programming process depends on the amount of current that is applied during the programming process (up to 130mA). This current must be provided by an external voltage source. If this voltage source cannot provide adequate power, the zener diodes may not be programmed properly. If a capacitor is connected to pin PROG, it should be removed during analog readback mode to allow a fast readout rate. If the capacitor is not removed the analog voltage will take longer to stabilize due to the additional capacitance. In order to verify the quality of the programmed bit, an analog level can be read for each zener diode, giving an indication whether this particular bit was properly programmed or not. The measured analog voltage for each bit must be subtracted from the previously measured V ref , and the resulting value gives an indication on the quality of the programmed bit: a reading of <100mV indicates a properly programmed bit and a reading of >1V indicates a properly unprogrammed bit. To put the AS5045 in Analog Readback Mode, a digital sequence must be applied to pins CSn, PROG and CLK as shown in Figure 12. The digital level for this pin depends on the supply configuration (3.3V or 5V; see section 0). A reading between 100mV and 1V indicates a faulty bit, which may result in an undefined digital value, when the OTP is read at power-up. The second rising edge on CSn (OutpEN) changes pin PROG to a digital output and the log. high signal at pin PROG must be removed to avoid collision of outputs (grey area in Figure 12). ProgEN Following the 18 th clock (after reading bit "ccw"), the chip must be reset by disconnecting the power supply. Power-onReset; turn off supply Analog Readback Data at PROG OutpEN CSn Vprogrammed Vref Internal test bit digital PWM Mag halfEN Comp EN Prog changes to Output PROG PWM Dis Z0 Vunprogrammed Z7 1 CLK tLoadProg Z8 Z9 Z10 Z11 CCW 16 CLKAread Figure 12: OTP register analog read Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 10 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 8 Alignment Mode The alignment mode simplifies centering the magnet over the center of the chip to gain maximum accuracy. Alignment mode can be enabled with the falling edge of CSn while Prog = logic high (Figure 13). The Data bits D9-D0 of the SSI change to a 12-bit displacement amplitude output. A high value indicates large X or Y displacement, but also higher absolute magnetic field strength. The magnet is properly aligned, when the difference between highest and lowest value over one full turn is at a minimum. Under normal conditions, a properly aligned magnet will result in a reading of less than 128 over a full turn. The MagINCn and MagDECn indicators will be = 1 when the alignment mode reading is < 128. At the same time, both hardware pins MagINCn (#1) and MagDECn (#2) will be pulled to VSS. A properly aligned magnet will therefore produce a MagINCn = MagDECn = 1 signal throughout a full 360 turn of the magnet. For 3.3V operation, the LDO must be bypassed by connecting VDD3V3 with VDD5V (see Figure 15). For 5V operation, the 5V supply is connected to pin VDD5V, while VDD3V3 (LDO output) must be buffered by a 1...10F capacitor, which is supposed to be placed close to the supply pin (see Figure 15). The VDD3V3 output is intended for internal use only It must not be loaded with an external load. The output voltage of the digital interface I/O's corresponds to the voltage at pin VDD5V, as the I/O buffers are supplied from this pin (see Figure 15). 5V Operation 1...10F VDD3V3 100n VDD5V LDO Internal VDD DO Stronger magnets or short gaps between magnet and IC may show values larger than 128. These magnets are still properly aligned as long as the difference between highest and lowest value over one full turn is at a minimum. I N T E R F A C E 4.5 - 5.5V The Alignment mode can be reset to normal operation by a power-on-reset (disconnect / re-connect power supply) or by a falling edge on CSn with Prog = low. PWM CLK CSn Prog VSS Prog 3.3V Operation AlignMode enable CSn Read-out via SSI VDD3V3 100n VDD5V DO 2s 2s min. min. 3.0 - 3.6V Figure 13: Enabling the alignment mode Prog CSn exit AlignMode LDO Internal VDD Read-out via SSI VSS I N T E R F A C E PWM CLK CSn Prog Figure 14: Exiting alignment mode 9 3.3V / 5V Operation Figure 15: Connections for 5V / 3.3V supply voltages The AS5045 operates either at 3.3V 10% or at 5V 10%. This is made possible by an internal 3.3V LowDropout (LDO) Voltage regulator. The internal supply voltage is always taken from the output of the LDO, meaning that the internal blocks are always operating at 3.3V. Revision 1.2, 03-Oct-06 A buffer capacitor of 100nF is recommended in both cases close to pin VDD5V. Note that pin VDD3V3 must always be buffered by a capacitor. It must not be left floating, as this may cause an instable internal 3.3V supply voltage which may lead to larger than normal jitter of the measured angle. www.austriamicrosystems.com Page 11 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 10 Choosing the Proper Magnet 10.1 Typically the magnet should be 6mm in diameter and 2.5mm in height. Magnetic materials such as rare earth AlNiCo/SmCo5 or NdFeB are recommended. The best linearity can be achieved by placing the center of the magnet exactly over the defined center of the chip as shown in the drawing below: Physical Placement of the Magnet 3.9 mm The magnetic field strength perpendicular to the die surface has to be in the range of 45mT...75mT (peak). The magnet's field strength should be verified using a gauss-meter. The magnetic field B v at a given distance, along a concentric circle with a radius of 1.1mm (R1), should be in the range of 45mT...75mT. (see Figure 16). N S Magnet axis R1 concentric circle; radius 1.1mm Vertical field component Rd Area of recommended maximum magnet misalignment Magnet Placement The magnet may be placed below or above the device. The distance should be chosen such that the magnetic field on the die surface is within the specified limits (see Figure 16). The typical distance "z" between the magnet and the package surface is 0.5mm to 1.5mm, provided the use of the recommended magnet material and dimensions (6mm x 3mm). Larger distances are possible, as long as the required magnetic field strength stays within the defined limits. However, a magnetic field outside the specified range may still produce usable results, but the out-of-range condition will be indicated by MagINCn (pin 1) and MagDECn (pin 2), see Table 1. (45...75mT) 0 Defined center The magnet's center axis should be aligned within a displacement radius R d of 0.25mm from the defined center of the IC. Vertical field component Bv 2.433 mm Figure 17: Defined chip center and magnet displacement radius Magnet axis R1 1 2.433 mm typ. 6mm diameter 3.9 mm 360 360 N Figure 16: Typical magnet (6x3mm) and magnetic field distribution Die surface S Package surface z 0.576mm 0.1mm 1.282mm 0.15mm Figure 18: Vertical placement of the magnet Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 12 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER The differential sampling of the sine and cosine vectors removes any common mode error due to DC components introduced by the magnetic source itself or external disturbing magnetic fields. A ratiometric division of the sine and cosine vectors removes the need for an accurate absolute magnitude of the magnetic field and thus accurate Z-axis alignment of the magnetic source. 11 Simulation Modeling 3.9 mm 0.235mm 1 2.433 mm Y1 0.235mm The recommended differential input range of the X1 X2 magnetic field strength (B (X1-X2) , B (Y1-Y2) ) is 75mT at the surface of the die. In addition to this range, an additional offset of 5mT, caused by unwanted external stray fields is allowed. Y2 AS5045 die Center of die Radius of circular Hall sensor array: 1.1mm radius The chip will continue to operate, but with degraded output linearity, if the signal field strength is outside the recommended range. Too strong magnetic fields will introduce errors due to saturation effects in the internal preamplifiers. Too weak magnetic fields will introduce errors due to noise becoming more dominant. Figure 19: Arrangement of Hall sensor array on chip (principle) 12 Failure Diagnostics With reference to Figure 19, a diametrically magnetized permanent magnet is placed above or below the surface of the AS5045. The chip uses an array of Hall sensors to sample the vertical vector of a magnetic field distributed across the device package surface. The area of magnetic sensitivity is a circular locus of 1.1mm radius with respect to the center of the die. The Hall sensors in the area of magnetic sensitivity are grouped and configured such that orthogonally related components of the magnetic fields are sampled differentially. The differential signal Y1-Y2 will give a sine vector of the magnetic field. The differential signal X1-X2 will give an orthogonally related cosine vector of the magnetic field. The angular displacement () of the magnetic source with reference to the Hall sensor array may then be modelled by: = arctan (Y 1 - Y 2) 0.5 ( X 1 - X 2) The 0.5 angular error assumes a magnet optimally aligned over the center of the die and is a result of gain mismatch errors of the AS5045. Placement tolerances of the die within the package are 0.235mm in X and Y direction, using a reference point of the edge of pin #1 (see Figure 19) In order to neglect the influence of external disturbing magnetic fields, a robust differential sampling and ratiometric calculation algorithm has been implemented. Revision 1.2, 03-Oct-06 The AS5045 also offers several diagnostic and failure detection features: 12.1 Magnetic Field Strength Diagnosis By software: the MagINC and MagDEC status bits will both be high when the magnetic field is out of range. By hardware: Pins #1 (MagINCn) and #2 (MagDECn) are open-drain outputs and will both be turned on (= low with external pull-up resistor) when the magnetic field is out of range. If only one of the outputs are low, the magnet is either moving towards the chip (MagINCn) or away from the chip (MagDECn). 12.2 Power Supply Failure Detection By software: If the power supply to the AS5045 is interrupted, the digital data read by the SSI will be all "0"s. Data is only valid, when bit OCF is high, hence a data stream with all "0"s is invalid. To ensure adequate low levels in the failure case, a pull-down resistor (~10k) should be added between pin DO and VSS at the receiving side By hardware: The MagINCn and MagDECn pins are open drain outputs and require external pull-up resistors. In normal operation, these pins are high ohmic and the outputs are high (see Table 5). In a failure case, either when the magnetic field is out of range of the power supply is missing, these outputs will become low. To ensure adequate low levels in case of a broken power supply to the AS5045, the pull-up resistors (~10k) from www.austriamicrosystems.com Page 13 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER each pin must be connected to the positive supply at pin 16 (VDD5V). Linearity Error over XY-misalignment [] By hardware: PWM output: The PWM output is a constant stream of pulses with 1kHz repetition frequency. In case of power loss, these pulses are missing 6 13 Angular Output Tolerances 4 Accuracy Accuracy is defined as the error between measured angle and actual angle. It is influenced by several factors: -600 -800 -1000 -1000 -400 -800 -600 y As a sum of all these errors, the accuracy with centered magnet = (Err max - Err min )/2 is specified as better than x -400 0 non-linearity due to misalignment of the magnet -200 0 -200 0 200 internal gain and mismatch errors, 400 200 1 600 2 400 the non-linearity of the analog-digital converters, 800 600 1000 1000 3 800 13.1 5 Figure 20: Example of linearity error over XY misalignment The maximum non-linearity error on this example is 0.5 degrees @ 25C (see Figure 21). better than 1 degree (inner circle) over a misalignment radius of ~0.7mm. For volume production, the placement Misalignment of the magnet further reduces the accuracy. Figure 20 shows an example of a 3D-graph displaying non-linearity over XY-misalignment. The center of the square XY-area corresponds to a centered magnet (see dot in the center of the graph). The X- and tolerance of the IC within the package (0.235mm) must also be taken into account. The total nonlinearity error over process tolerances, temperature and a misalignment circle radius of 0.25mm Y- axis extends to a misalignment of 1mm in both directions. The total misalignment area of the graph covers a square of 2x2 mm (79x79mil) with a step size of 100m. is specified better than 1.4 degrees. The magnet used for this measurement was a cylindrical NdFeB (Bomatec(R) BMN-35H) magnet with 6mm diameter and 2.5mm in height. For each misalignment step, the measurement as shown in Figure 21 is repeated and the accuracy (Err max - Err min )/2 (e.g. 0.25 in Figure 21) is entered as the Z-axis in the 3D-graph. Linearity error with centered magnet [degrees] 0.5 0.4 0.3 0.2 transition noise 0.1 Err m ax 0 -0.1 1 55 109 163 217 271 325 379 433 487 541 595 649 703 757 811 865 919 973 Err m in -0.2 -0.3 -0.4 -0.5 Figure 21: Example of linearity error over 360 Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 14 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 13.2 Transition Noise Transition noise is defined as the jitter in the transition between two steps. Due to the nature of the measurement principle (Hall sensors + Preamplifier + ADC), there is always a certain degree of noise involved. This transition noise voltage results in an angular transition noise at the outputs. It is specified as 0.06 degrees rms (1 sigma) *1 in fast mode (pin MODE = high) and 0.03 degrees rms (1 sigma) *1 in slow mode (pin MODE = low or open). This is the repeatability of an indicated angle at a given mechanical position. The transition noise has different implications on the type of output that is used: Absolute output; SSI interface: The transition noise of the absolute output can be reduced by the user by implementing averaging of readings. An averaging of 4 readings will reduce the transition noise by 6dB or 50%, e.g. from 0.03rms to 0.015rms (1 sigma) in slow mode. PWM interface: If the PWM interface is used as an analog output by adding a low pass filter, the transition noise can be reduced by lowering the cutoff frequency of the filter. If the PWM interface is used as a digital interface with a counter at the receiving side, the transition noise may again be reduced by averaging of readings. : statistically, 1 sigma represents 68.27% of readings, 3 sigma represents 99.73% of readings. *1 13.3 High Speed Operation 13.3.1 Sampling Rate nslow mod e = 60 rpm 384 s n fast mod e = 60 rpm 96 s The upper speed limit in slow mode is ~6.000rpm and ~30.000rpm in fast mode. The only restriction at high speed is that there will be fewer samples per revolution as the speed increases (see Table 2). Regardless of the rotational speed, the absolute angular value is always sampled at the highest resolution of 12 bit. 13.4 Propagation Delays The propagation delay is the delay between the time that the sample is taken until it is converted and available as angular data. This delay is 96s in fast mode and 384s in slow mode. Using the SSI interface for absolute data transmission, an additional delay must be considered, caused by the asynchronous sampling (0 ... 1/f sample ) and the time it takes the external control unit to read and process the angular data from the chip (maximum clock rate = 1MHz, number of bits per reading = 18). 13.4.1 Angular Error Caused by Propagation Delay A rotating magnet will cause an angular error caused by the output propagation delay. This error increases linearly with speed: e sampling , = rpm 6 * prop.delay where e sampling = angular error [] rpm = rotating speed [rpm] prop.delay = propagation delay [seconds] Note: since the propagation delay is known, it can be automatically compensated by the control unit processing the data from the AS5045. The AS5045 samples the angular value at a rate of 2.61k (slow mode) or 10.42k (fast mode, selectable by pin MODE) samples per second. Consequently, the absolute outputs are updated each 384s (96s in fast mode). At a stationary position of the magnet, the sampling rate creates no additional error. Absolute Mode At a sampling rate of 2.6kHz/10.4kHz, the number of samples (n) per turn for a magnet rotating at high speed can be calculated by Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 15 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 13.5 Internal Timing Tolerance The AS5045 does not require an external ceramic resonator or quartz. All internal clock timings for the AS5045 are generated by an on-chip RC oscillator. This oscillator is factory trimmed to 5% accuracy at room temperature (10% over full temperature range). This tolerance influences the ADC sampling rate and the pulse width of the PWM output: Absolute output; SSI interface: A new angular value is updated every 400s (typ.) PWM output: A new angular value is updated every 400s (typ.). The PWM pulse timings T on and T off also have the same tolerance as the internal oscillator (see above). If only the PWM pulse width T on is used to measure the angle, the resulting value also has this timing tolerance. However, this tolerance can be cancelled by measuring both T on and T off and calculating the angle from the duty cycle (see section 5): Position = ton 4097 (ton + toff ) - 1 13.6 Temperature 13.6.1 Magnetic Temperature Coefficient One of the major benefits of the AS5045 compared to linear Hall sensors is that it is much less sensitive to temperature. While linear Hall sensors require a compensation of the magnet's temperature coefficients, the AS5045 automatically compensates for the varying magnetic field strength over temperature. The magnet's temperature drift does not need to be considered, as the AS5045 operates with magnetic field strengths from 45...75mT. Example: A NdFeB magnet has a field strength of 75mT @ -40C and a temperature coefficient of -0.12% per Kelvin. The temperature change is from -40 to +125 = 165K. The magnetic field change is: 165 x -0.12% = -19.8%, which corresponds to 75mT at -40C and 60mT at 125C. The AS5045 can compensate for this temperature related field strength change automatically, no user adjustment is required. 13.7 Accuracy over Temperature The influence of temperature in the absolute accuracy is very low. While the accuracy is 0.5 at room temperature, it may increase to 0.9 due to increasing noise at high temperatures. 13.7.1 Timing Tolerance over Temperature The internal RC oscillator is factory trimmed to 5%. Over temperature, this tolerance may increase to 10%. Generally, the timing tolerance has no influence in the accuracy or resolution of the system, as it is used mainly for internal clock generation. The only concern to the user is the width of the PWM output pulse, which relates directly to the timing tolerance of the internal oscillator. This influence however can be cancelled by measuring the complete PWM duty cycle instead of just the PWM pulse (see 13.5). Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 16 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 14 Electrical Characteristics 14.1 AS5045 Differences to AS5040 All parameters are according to AS5040 datasheet except for the parameters shown below: Building Block AS5045 AS5040 Resolution 12bits, 0.088/step. 10bits, 0.35/step Data length read: 18bits (12bits data + 6 bits status) OTP write: 18 bits (12bits zero position + 6 bits mode selection) read: 16bits (10bits data + 6 bits status) OTP write: 16 bits (10bits zero position + 6 bits mode selection) incremental encoder Not used Pin 3: not used Pin 4:not used quadrature, step/direction and BLDC motor commutation modes Pin 3:incremental output A_LSB_U Pin 4:incremental output B_DIR_V Pins 1 and 2 MagINCn, MagDECn: same feature as AS5040, additional OTP option for red-yellow-green magnetic range MagINCn, MagDECn indicate in-range or out-of-range magnetic field plus movement of magnet in z-axis Pin 6 MODE pin, switch between fast and slow mode Pin 6:Index output Pin 12 PWM output: frequency selectable by OTP: 1s / step, 4096 steps per revolution, f=244Hz 2s/ step, 4096 steps per revolution, f=122Hz PWM output: 1s / step, 1024 steps per revolution, 976Hz PWM frequency sampling frequency selectable by MODE input pin: 2.5kHz, 10kHz fixed at 10kHz @10bit resolution Propagation delay 384s (slow mode) 96s (fast mode) 48s Transition noise (rms; 1sigma) 0.03 degrees max. (slow mode) 0.06 degrees max. (fast mode) 0.12 degrees OTP programming options zero position, rotational direction, PWM disable, 2 Magnetic Field indicator modes, 2 PWM frequencies zero position, rotational direction, incremental modes, index bit width 14.2 Absolute Maximum Ratings (non operating) Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only. Functional operation of the device at these or any other conditions beyond those indicated under "Operating Conditions" is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Parameter Symbol Min Max Unit DC supply voltage at pin VDD5V VDD5V -0.3 7 V DC supply voltage at pin VDD3V3 VDD3V3 5 V Note Input pin voltage Vin -0.3 VDD5V +0.3 V Except VDD3V3 Input current (latchup immunity) Iscr -100 100 mA Norm: JEDEC 78 2 kV Norm: MIL 883 E method 3015 125 C Min - 67F ; Max +257F 260 C 85 % Electrostatic discharge ESD Storage temperature Tstrg Body temperature (Lead-free package) TBody Humidity non-condensing Revision 1.2, 03-Oct-06 H -55 5 www.austriamicrosystems.com t=20 to 40s, Norm: IPC/JEDEC J-Std-020C Lead finish 100% Sn "matte tin" Page 17 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 14.3 Operating Conditions Parameter Symbol Min Typ Max Unit Ambient temperature Tamb -40 125 C Supply current Isupp 16 21 mA Supply voltage at pin VDD5V VDD5V 4.5 5.0 5.5 V Voltage regulator output voltage at pin VDD3V3 VDD3V3 3.0 3.3 3.6 V Supply voltage at pin VDD5V VDD5V 3.0 3.3 3.6 V Supply voltage at pin VDD3V3 VDD3V3 3.0 3.3 3.6 V 14.4 DC Characteristics for Digital Inputs and Outputs 14.4.1 CMOS Schmitt-Trigger Inputs: CLK, CSn. (CSn = internal Pull-up) Note -40F...+257F 5V Operation 3.3V Operation (pin VDD5V and VDD3V3 connected) (operating conditions: T am b = -40 to +125C, VDD5V = 3.0-3.6V (3V operation) VDD5V = 4.5-5.5V (5V operation) unless otherwise noted) Parameter Symbol Min High level input voltage VIH 0.7 * VDD5V Low level input voltage VIL Schmitt Trigger hysteresis Input leakage current Pull-up low level input current 14.4.2 Max Unit Note V 0.3 * VDD5V Normal operation V VIon- VIoff 1 V ILEAK -1 1 A CLK only IiL -30 -100 A CSn only, VDD5V: 5.0V CMOS / Program Input: Prog (operating conditions: T am b = -40 to +125C, VDD5V = 3.0-3.6V (3V operation) VDD5V = 4.5-5.5V (5V operation) unless otherwise noted) Parameter Symbol Min Max Unit High level input voltage VIH 0.7 * VDD5V VDD5V V High level input voltage VPROG Low level input voltage VIL High level input current IiL 14.4.3 See "programming conditions" 30 Note V 0.3 * VDD5V V 100 A During programming VDD5V: 5.5V CMOS Output Open Drain: MagINCn, MagDECn (operating conditions: T am b = -40 to +125C, VDD5V = 3.0-3.6V (3V operation) VDD5V = 4.5-5.5V (5V operation) unless otherwise noted) Parameter Low level output voltage Symbol VOL Output current IO Open drain leakage current IOZ Revision 1.2, 03-Oct-06 Min www.austriamicrosystems.com Max Unit VSS+0.4 V 4 2 1 mA Note VDD5V: 4.5V VDD5V: 3V A Page 18 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 14.4.4 CMOS Output: PWM (operating conditions: T am b = -40 to +125C, VDD5V = 3.0-3.6V (3V operation) VDD5V = 4.5-5.5V (5V operation) unless otherwise noted) Parameter Symbol Min High level output voltage VOH VDD5V-0.5 Low level output voltage VOL Output current 14.4.5 Max Unit Note V IO VSS+0.4 V 4 mA VDD5V: 4.5V 2 mA VDD5V: 3V Tristate CMOS Output: DO (operating conditions: T am b = -40 to +125C, VDD5V = 3.0-3.6V (3V operation) VDD5V = 4.5-5.5V (5V operation) unless otherwise noted) Parameter Symbol Min High level output voltage VOH VDD5V -0.5 Low level output voltage VOL VSS+0.4 V IO 4 mA VDD5V: 4.5V 2 mA VDD5V: 3V 1 A Output current Tri-state leakage current 14.5 Max Unit Note V IOZ Magnetic Input Specification (operating conditions: T am b = -40 to +125C, VDD5V = 3.0-3.6V (3V operation) VDD5V = 4.5-5.5V (5V operation) unless otherwise noted) Two-pole cylindrical diametrically magnetised source: Parameter Symbol Min Typ Diameter dmag 4 6 Thickness tmag 2.5 Magnetic input field amplitude Bpk 45 Magnetic offset Boff (rotational speed of magnet) mm Recommended magnet: O 6mm x 2.5mm for cylindrical magnets Eccentricity Ecc -0.12 -0.035 Required vertical component of the magnetic field strength on the die's surface, measured along a concentric circle with a radius of 1.1mm mT 10 mT Constant magnetic stray field 5 % Including offset gradient Hz 0,61 Disp Revision 1.2, 03-Oct-06 Note 75 2,44 fmag_abs Displacement radius Recommended magnet material and temperature drift Unit mm Field non-linearity Input frequency Max 146 rpm @ 4096 positions/rev.; fast mode 36.6rpm @ 4096 positions/rev.; slow mode 0.25 mm Max. offset between defined device center and magnet axis (see Figure 17) 100 m Eccentricity of magnet center to rotational axis %/K www.austriamicrosystems.com NdFeB (Neodymium Iron Boron) SmCo (Samarium Cobalt) Page 19 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 14.6 Electrical System Specifications (operating conditions: T am b = -40 to +125C, VDD5V = 3.0-3.6V (3V operation) VDD5V = 4.5-5.5V (5V operation) unless otherwise noted) Parameter Symbol Resolution Max Unit RES 12 bit 0.088 deg Integral non-linearity (optimum) INLopt 0.5 deg Maximum error with respect to the best line fit. Centered magnet without calibration, Tamb =25 C. Integral non-linearity (optimum) INLtemp 0.9 deg Maximum error with respect to the best line fit. Centered magnet without calibration, Tamb = -40 to +125C Integral non-linearity INL 1.4 deg Best line fit = (Errmax - Errmin) / 2 Over displacement tolerance with 6mm diameter magnet, without calibration, Tamb = -40 to +125C Differential non-linearity DNL 0.044 deg 12bit, no missing codes 0.06 1 sigma, fast mode (MODE = 1) 0.03 Deg RMS 2.9 2.6 V V Transition noise TN Power-on reset thresholds Von Voff On voltage; 300mV typ. hysteresis Off voltage; 300mV typ. hysteresis Power-up time tPwrUp System propagation delay absolute output : delay of ADC, DSP and absolute interface tdelay 1,37 1.08 fS Internal sampling rate for absolute output fS Read-out frequency 12bit code Typ 2.2 1.9 20 ms 80 96 s 384 2.48 Internal sampling rate for absolute output: 4095 Min 2.61 2.74 Note 1 sigma, slow mode (MODE=0 or open) DC supply voltage 3.3V (VDD3V3) DC supply voltage 3.3V (VDD3V3) Fast mode (Mode = 1); Until status bit OCF = 1 Slow mode (Mode = 0 or open); Until OCF = 1 Fast mode (MODE=1) Slow mode (MODE=0 or open) Tamb = 25C, slow mode (MODE=0 or open) kHz 2.35 2.61 2.87 9.90 10.42 10.94 9.38 10.42 11.46 kHz Tamb = -40 to +125C, : fast mode (MODE = 1) 1 MHz Max. clock frequency to read out serial data CLK Tamb = -40 to +125C, slow mode (MODE=0 or open) Tamb = 25C, fast mode (MODE = 1) 4095 Actual curve 2 TN DNL+1LSB 1 0 2048 Ideal curve INL 0.09 2048 0 0 180 360 [degrees] Figure 22: Integral and differential non-linearity (example) Integral Non-Linearity (INL) is the maximum deviation between actual position and indicated position. Differential Non-Linearity (DNL) is the maximum deviation of the step length from one position to the next. Transition Noise (TN) is the repeatability of an indicated position Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 20 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 15 Timing Characteristics Synchronous Serial Interface (SSI) (operating conditions: T am b = -40 to +125C, VDD5V = 3.0-3.6V (3V operation) VDD5V = 4.5-5.5V (5V operation) unless otherwise noted) Parameter Symbol Data output activated (logic high) t DO active First data shifted to output register tCLK FE Start of data output Min Max Unit 100 ns Time between falling edge of CSn and data output activated 500 ns Time between falling edge of CSn and first falling edge of CLK T CLK / 2 500 ns Rising edge of CLK shifts out one bit at a time Data output valid t DO valid 357 394 ns Time between rising edge of CLK and data output valid Data output tristate t DO tristate 100 ns After the last bit DO changes back to "tristate" ns CSn = high; To initiate read-out of next angular position Pulse width of CSn t CSn 500 Read-out frequency fCLK >0 15.1.1 Typ 375 1 MHz Note Clock frequency to read out serial data Pulse Width Modulation Output (operating conditions: T am b = -40 to +125C, VDD5V = 3.0-3.6V (3V operation) VDD5V = 4.5-5.5V (5V operation) unless otherwise noted) Parameter Symbol PWM frequency Minimum pulse width Min Typ Max 232 244 256 220 244 268 0.95 1 1.05 f PWM PW MIN Unit Hz s Note Signal period = 4097s 5% at Tamb = 25C =4097s 10% at Tamb = -40 to +125C Position 0d; Angle 0 degree Maximum pulse width PW MAX 3891 4096 4301 s Position 4095d; Angle 359.91 degrees Note: when OTP bit "PWMhalfEn" is set, the PWM pulse width PW is doubled (PWM frequency f PWM is divided by 2) 15.2 Programming Conditions (operating conditions: T am b = -40 to +125C, VDD5V = 3.0-3.6V (3V operation) VDD5V = 4.5-5.5V (5V operation) unless otherwise noted) Parameter Symbol Min Typ Max Unit Programming enable time t Prog enable 2 s Write data start t Data in 2 s Write data valid t Data in valid 250 ns Load Programming data t Load PROG 3 s Rise time of VPROG before CLKPROG t PrgR 0 s Hold time of VPROG after CLK PROG t PrgH 0 Note Time between rising edge at Prog pin and rising edge of CSn Write data at the rising edge of CLK PROG 5 s 250 kHz ensure that VPROG is stable with rising edge of CLK 2.2 s during programming; 16 clock cycles s Programmed data is available after next power-on 7.5 V Must be switched off after zapping 1 V Line must be discharged to this level I PROG 130 mA during programming Analog Read CLK CLKAread 100 kHz Analog Readback mode Programmed Zener Voltage (log.1) Vprogrammed 100 mV Unprogrammed Zener Voltage (log. 0) Vunprogrammed VRef-VPROG during Analog Readback mode (see 7.4) Write data - programming CLK PROG CLK pulse width CLK PROG t PROG 1.8 t PROG finished 2 Programming voltage, pin PROG V PROG 7.3 Programming voltage off level V ProgOff 0 Hold time of Vprog after programming Programming current Revision 1.2, 03-Oct-06 2 7.4 1 www.austriamicrosystems.com V Page 21 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 16 Package Drawings and Markings 16-Lead Shrink Small Outline Package SSOP-16 AYWWIZZ AS5045 Dimensions Symbol Marking: AYWWIZZ mm Min Typ inch Max Min A: Pb-Free Identifier Typ Max Y: Last Digit of Manufacturing Year A 1.73 1.86 1.99 .068 .073 .078 WW: Manufacturing Week A1 0.05 0.13 0.21 .002 .005 .008 I: Plant Identifier A2 1.68 1.73 1.78 .066 .068 .070 ZZ: Traceability Code b 0.25 0.315 0.38 .010 .012 .015 c 0.09 - 0.20 .004 - .008 D 6.07 6.20 6.33 .239 .244 .249 E 7.65 7.8 7.9 .301 .307 .311 E1 5.2 5.3 5.38 .205 .209 .212 e 0.65 .0256 K 0 - 8 0 - 8 L 0.63 0.75 0.95 .025 .030 .037 JEDEC Package Outline Standard: MO - 150 AC Thermal Resistance R th(j-a) : typ. 151 K/W in still air, soldered on PCB IC's marked with a white dot or the letters "ES" denote Engineering Samples 17 Ordering Information Delivery: Tape and Reel (1 reel = 2000 devices) Tubes (1 box = 100 tubes a 77 devices) Order # AS5045ASSU Order # AS5045ASST Revision 1.2, 03-Oct-06 for delivery in tubes for delivery in tape and reel www.austriamicrosystems.com Page 22 of 23 AS5045 12-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER 18 Recommended PCB Footprint: Recommended Footprint Data A B C D E mm 9.02 6.16 0.46 0.65 5.01 inch 0.355 0.242 0.018 0.025 0.197 19 Revision History Revision Date Description 1.2 Oct. 03, 2006 Update description of Alignment Mode (8) and OTP programming (7.2, 7.3), Table 2, Isupp (14.3), Boff (14.5), t DO valid (15), definition of magnet thickness 1.1 Mar. 24, 2006 Added OTP prog. timing table 15.2, New Figure 10, Figure 11 1.0 Dec. 7, 2004 Initial revision Sep. 26, 2005 Official release Jan. 11, 2006 Modify Figure 1, thermal resistance (Package Drawings and Markings) 20 Contact 20.1 Headquarters austriamicrosystems AG A 8141 Schloss Premstatten, Austria Phone: +43 3136 500 0 Fax: +43 3136 525 01 info@austriamicrosystems.com?subject=AS5045 www.austriamicrosystems.com Copyright Devices sold by austriamicrosystems are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems for current information. This product is intended for use in normal commercial applications. Copyright (c) 2005 austriamicrosystems. Trademarks registered (R). All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. To the best of its knowledge, austriamicrosystems asserts that the information contained in this publication is accurate and correct. However, austriamicrosystems shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems rendering of technical or other services. Revision 1.2, 03-Oct-06 www.austriamicrosystems.com Page 23 of 23