※1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at 125°C .
※2 Refer to Page 56 for reflow soldering conditions.
C6
E7
6.3
8.0
W
±
0.2
φD
±
0.5
5.9
6.9
6.6
8.3
H±0.2
6.6
8.3
C±0.2
7.3
9.0
R
0.6 to 0.8
0.6 to 0.8
P±0.2
2.1
3.2
Size Code
(unit : mm)
■Size List
28
22
39
47
56
82
100
120
150
220
C6
E7
RV
（SV）
µF
4
（5.2）6.3
（8.2）10
（11.5）16
（18.4）20
（23）
C6
C6
E7
E7
C6
E7
E7
C6
E7
C6
E7
RV : Rated voltage (SV) : Surge (room temperature)
■Dimensions
※For the minimum packing quantity, please refer to page 55.
This series has advanced characteristics in resistance to heat compared with
the SVP series. The SVQP series is best suited for devices that require
enhanced reliability.
This product can support lead free-reflow.(※2).
Marking : Polarity( ), Rated voltage
(Purple) QP, Rated capacitance, Lot.No.
■Specifications
Specificationsfor
eachseries
4. SPECIFICATIONS FOR EACH SERIES
φD
L
P
R
C
W
0.2max.
H
（＋）
Conductive polymer type
SVQPSeries Guaranteed at 125°C
L+0.1
-0.4
Items Characteristics
-55°C to +125°C
M : ±20%
Less than or equal to the value of Table6
Less than or equal to the value of Table6
Less than or equal to the value of Table6
Within ±20%
2 times or less than an initial standard
2 times or less than an initial standard
Below an initial standard
Within ±20%
1.5 times or less than an initial standard
1.5 times or less than an initial standard
Below an initial standard (after voltage processing)
Within ±10%
1.3 times or less than an initial standard
1.3 times or less than an initial standard
Below an initial standard (after voltage processing)
Category temperature range
Tolerance on rated capacitance
Tangent of loss angle
Leakage current
ESR
Endurance
Damp heat (Steady state)
Characteristics of impedance
ratio at high temp. and low temp.
-55°C
+125°C
∆C/C
tanδ
ESR
Leakage current
∆C/C
tanδ
ESR
Leakage current
∆C/C
tanδ
ESR
Leakage current
Resistance to
soldering heat
Z / Z 20°C
Z / Z 20°C
0.75 to 1.25
0.75 to 1.25
120Hz
120Hz
125°C, 1,000h, Rated
voltage applied
60°C, 90 to 95%RH,
1,000h,
No-applied voltage
(VPS) (230°C X 75s)
※1
※2
Conditions
Based the value at
100KHz，+20°C
After 2 minutes
29
※1 Capacitance tolerance : M ±20%
※2 After 2 minutes
※3 Tx : Ambient temperature
20SVQP22M
16SVQP39M
10SVQP56M
6SVQP82M
6SVQP100M
4SVQP150M
20SVQP47M
16SVQP82M
10SVQP120M
10SVQP150M
6SVQP150M
6SVQP220M
4SVQP220M
20
16
10
6.3
6.3
4
20
16
10
10
6.3
6.3
4
■Recommended land pattern
dimension of PWB
C6
E7
22
39
56
82
100
150
47
82
120
150
150
220
220
60
50
45
45
40
40
45
40
35
35
35
35
35
459
512
538
538
572
572
598
670
810
810
810
810
810
1450
1620
1700
1700
1810
1810
1890
2120
2560
2560
2560
2560
2560
0.10
0.10
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
220
312
280
258
315
300
470
656
600
750
472
693
440
Size Code
C6
E7
ab c
2.1
2.8
9.1
11.1
1.6
1.9
(unit : mm)
c
a
b
Size
Code
4. SPECIFICATIONS FOR EACH SERIES
■Table6 SVQP Series Characteristics List
Part Number
※1
Tangent of
loss angle
(max.)
Leakage
current (µA)
(max.)※2
Rated
Voltage
(V)
Rated
Capacitance
(µF)
ESR
100kHz to 300kHz
(mΩ) (max.)
100kHz (mArms) ※3
Rated ripple current
Allowable ripple current
105℃＜Tx≦125℃
Tx≦105℃
Specificationsfor
eachseries
Frequency coefficient for ripple current
Frequency
Coefficient
120Hz≦ f ＜1kHz
0.05
1kHz≦ f ＜10kHz
0.3
10kHz≦ f ＜100kHz
0.7
100kHz≦ f ≦500kHz
1