LPC11C14FBD48/301,151 - NXP SEMICONDUCTORS

1. Product profile

1.1 General description

The LD6806 series is a small-size Low-DropOut regulator (LDO) family with a typical

voltage drop of 60 mV at 200 mA current rating.

The device is available in three different surface-mounted packages, one 0.4 mm pitch

CSP, one leadless plastic package SOT886 and one gull wing package SOT753.

The operating voltage ranges from 2.3 V to 5.5 V and the output voltage ranges from

1.2 V to 3.6 V.

LD6806x/xxH devices show a high-ohmic state at the output pin, while the LD6806x/xxP

contains a pull-down switching transistor, to provide a low-ohmic output stage when the

device is disabled. All devices use the same regulator design and are manufactured in

monolithic silicon technology.

These features make the LD6806 ser ies ideal for u se in applica tions requiring co mponent

miniaturization, such as mob ile phone han dsets, cordle ss telephones and pe rsonal digit al

devices.

1.2 Features and benefits

Input voltage range 2.3 V to 5.5 V

Output voltage range 1.2 V to 3.6 V

Dropout voltage 60 mV at 200 mA outpu t ra ting

Low quiescent current in shutdown mode (typical 1.0 A)

30 V RMS output noise voltage (typical value) at 10 Hz to 100 kHz

Turn-on time just 200 s

55 dB Power Supply Rejection Ratio (PSRR) at 1 kHz

Temperature watchdog

Current limiter

LD6806xxxH: high-ohmic (3-state) output state when disabled

LD6806xxxP: low-ohmic output state when disabled

Integrated ESD protection of 10 kV Human Body Model

WLCSP with 0.4 mm pitch and package size of 0.76 mm 0.76 mm 0.47 mm

SOT886 leadless package 1.0 mm 1.45 mm 0.5 mm

SOT753 plastic surface-mounted device

Pb-free, RoHS compliant and free of Halogen and Antimony (dark green compliant)

LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

Rev. 3 — 9 December 2011 Product data sheet

Product data sheet Rev. 3 — 9 December 2011 2 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

1.3 Applications

Analog and digital interfaces requiring lower than standard supply voltage in mobile

appliances such as mobile phones, media players and so on.

2. Pinning information

2.1 Pinning

2.2 Pin description

Fig 1. Configuration for SOT 753 Fig 2. Configuratio n for WLCSP4 Fig 3. Configurat ion for SOT886

132

001aao10

transparent top view,

solder balls facing down

bump A1

index area

LD6806

n.c.

001aao333

OUT

GND

n.c.

Transparent top view

Table 1. Pin description for SOT 753

Symbol Pin Description

IN 1 supply voltage input

GND 2 supply ground

EN 3 device enable input; active HIGH

n.c. 4 not connected

OUT 5 regulator output voltage

Table 2. Pin description for WL CSP4

Symbol Pin Description

GND A1 supply ground

EN A2 device enable input; active HIGH

OUT B1 regulator output voltage

IN B2 supply voltage input

Table 3. Pin description for SOT 886

Symbol Pin Description

OUT 1 regulator output voltage

n.c. 2 not connected

GND 3 supply ground

Product data sheet Rev. 3 — 9 December 2011 3 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

3. Ordering information

[1] Size 0.76 mm 0.76 mm.

3.1 Ordering options

Further information on output voltage is available on request; see Section 21 “Contact

information”.

EN 4 device enable input; active HIGH

n.c. 5 not connected

IN 6 supply voltage input

Table 3. Pin description for SOT 886

Symbol Pin Description

Table 4. Ordering info rmation

Type number Package

Name Description Version

LD6806CX4/xxx WLCSP4 wafer level chip-size package; 4 bumps (2 2)[1] -

LD6806CX4/C/xxx WLCSP4 wafer level chip-size package; 4 bumps (2 2)

with backside coating[1] -

LD6806F/xxx XSON6 plastic extremely thin small outline package; no

leads; 6 terminals; body 1 1.45 0.5 mm SOT886

LD6806TD/xxx TSOP5 plastic surface-mounted package; 5 leads SOT753

Table 5. Type number and nominal output voltage of high-ohmic output

Type number Nominal

output

voltage

Type number Nominal

output

voltage

LD6806[CX4, CX4/C, F, TD]/12H 1.2 V LD6806[CX4, CX4/C, F, TD]/23H 2.3 V

LD6806[CX4, CX4/C, F, TD]/13H 1.3 V LD6806[CX4, CX4/C, F, TD]/25H 2.5 V

LD6806[CX4, CX4/C, F, TD]/14H 1.4 V LD6806[CX4, CX4/C, F, TD]/28H 2.8 V

LD6806[CX4, CX4/C, F, TD]/16H 1.6 V LD6806[CX4, CX4/C, F, TD]/29H 2.9 V

LD6806[CX4, CX4/C, F, TD]/18H 1.8 V LD6806[CX4, CX4/C, F, TD]/30H 3.0 V

LD6806[CX4, CX4/C, F, TD]/20H 2.0 V LD6806[CX4, CX4/C, F, TD]/33H 3.3 V

LD6806[CX4, CX4/C, F, TD]/22H 2.2 V LD6806[CX4, CX4/C, F, TD]/36H 3.6 V

Table 6. Type number and nominal output voltage of low.ohmic output

Type number Nominal

output

voltage

Type number Nominal

output

voltage

LD6806[CX4, CX4/C, F, TD]/12P 1.2 V LD6806[CX4, CX4/C, F, TD]/23P 2.3 V

LD6806[CX4, CX4/C, F, TD]/13P 1.3 V LD6806[CX4, CX4/C, F, TD]/25P 2.5 V

LD6806[CX4, CX4/C, F, TD]/14P 1.4 V LD6806[CX4, CX4/C, F, TD]/28P 2.8 V

LD6806[CX4, CX4/C, F, TD]/16P 1.6 V LD6806[CX4, CX4/C, F, TD]/29P 2.9 V

Product data sheet Rev. 3 — 9 December 2011 4 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

4. Block diagram

LD6806[CX4, CX4/C, F, TD]/18P 1.8 V LD6806[CX4, CX4/C, F, TD]/30P 3.0 V

LD6806[CX4, CX4/C, F, TD]/20P 2.0 V LD6806[CX4, CX4/C, F, TD]/33P 3.3 V

LD6806[CX4, CX4/C, F, TD]/22P 2.2 V LD6806[CX4, CX4/C, F, TD]/36P 3.6 V

Table 6. Type number and nominal output voltage of low.ohmic output …continued

Type number Nominal

output

voltage

Type number Nominal

output

voltage

Fig 4. Block diagram of LD6806x/xxH

Fig 5. Block diagram of LD6806x/xxP

001aan756

THERMAL

PROTECTION

OVERCURRENT

PROTECTION

Vreference

GENERATOR

VIN VOUT

GND

VEN

001aan299

THERMAL

PROTECTION

OVER CURRENT

PROTECTION

Vreference

GENERATOR

VIN VOUT

GND

VEN

Product data sheet Rev. 3 — 9 December 2011 5 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

5. Limiting values

[1] The (absolute) maximum power dissipation depends on the junction temperature Tj. Higher power dissipation is allowed with lower

ambient temperatures. The conditions to determine the specified values are Tamb = 25 C and the use of a two layer PCB.

[2] According to IEC 61340-3-1.

[3] According to JESD22-A115C.

6. Recommended operating conditions

[1] See Section 10.1 “Output capacitor values”.

Table 7. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).

Symbol Parameter Conditions Min Max Unit

VIN voltage on pin IN 4 ms transient 0.5 +6.0 V

Ptot total power dissipation LD6806CX4/xxx,

LD6806CX4/Cxxx [1] -770mW

LD6806F/xxx [1] -450mW

LD6806TD/xxx [1] -800mW

Tstg storage temperature 55 +150 C

Tjjunctio n te mp erature 40 +125 C

Tamb ambient temperature 40 +85 C

VESD electrostatic discharge voltage human body model level 6 [2] 10 kV

machine model class 3 [3] -400 V

Table 8. Operating conditions

Voltages are referenced to GND (ground = 0 V).

Symbol Parameter Conditions Min Max Unit

Tamb ambient temperature 40 +85 C

Tjjunction temperature - +125 C

Pin IN

VIN voltage on pin IN 2.3 5.5 V

Pin EN

VEN voltage on pin EN 0 VIN V

Pin OUT

CL(ext) external load capacitance [1] 1.0 - F

Product data sheet Rev. 3 — 9 December 2011 6 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

7. Thermal characteristics

[1] The overall Rth(j-a) can vary depending on the board layout. To minimize the effective Rth(j-a), all pins must have a solid connection to

larger Cu layer areas for example to the power and ground layer. In multi-layer PCB applications, the second layer should be used to

create a large heat spreader area directly below the LDO. If this layer is either ground or power , it should be connected with several vias

to the top layer connecting to the device ground or supply. Avoid the use of solder-stop varnish under the chip.

[2] Use the measurement data given for a rough estimation of the Rth(j-a) in your application. The actual Rth(j-a) value can vary in applications

using different layer stacks and layouts.

8. Characteristics

Table 9. Thermal characteristics

Symbol Parameter Conditions Typ Unit

Rth(j-a) thermal resistance from junction to ambient LD6806CX4/xxx,

LD6806CX4/Cxxx [1][2] 130 K/W

LD6806F/xxx [1][2] 220 K/W

LD6806TD/xxx [1][2] 125 K/W

Table 10. Electrical characteristics

At recommended input voltages and Tamb =





Cto+85



C; voltages are referenced to GND (ground = 0 V);

unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

VOoutput voltage variation VOUT < 1.8 V; IOUT = 1 m A

Tamb = +25 C30.5 +3 %

30 C Tamb  +85 C4- +4 %

VOUT  1.8 V; IOUT = 1 mA

Tamb = +25 C20.5 +2 %

30 C Tamb  +85 C3- +3 %

Line regulation error

VO/(VOxVI) rel ative output voltage

variation with input voltage VIN = (VO(nom) + 0.2 V) to 5.5 V [1] 0.1 - +0.1 %/V

Load regulation error

VO/(VOxIO) relative output voltage

variation with output current 1mA  IOUT  200 mA

LD6806CX4/xxx, LD6806CX4/Cxxx - 0.0025 0.01 %/mA

LD6806F/xxx, LD6806TD/xxx - 0.005 0.02 %/mA

Vdo dropout voltage IOUT = 200 mA; VIN >V

O(nom) [1]

LD6806CX4/xxx, LD6806CX4/Cxxx - 60 100 mV

LD6806F/xxx, LD6806TD/xxx - 80 130 mV

VIL LOW-level input voltage pin EN 0 - 0.4 V

VIH HIGH-level input voltage pin EN 1.4 - 5.5 V

IOUT current on pin OUT - - 200 mA

IOM peak output current VIN =(V

O(nom) + 0.2 V) to 5.5 V [1]

VO(nom) > 1.8 V ;

VOUT  0.95 VO(nom)

300 - - mA

VO(nom) < 1.8 V ;

VOUT  0.9 VO(nom)

300 - - mA

Product data sheet Rev. 3 — 9 December 2011 7 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

[1] VO(nom) = nominal output voltage (device specific).

[2] The junction temperature must decrease by Tsd(hys) to enable the device after Tsd was reached and the device was disabled.

[3] LD6806x/xxP only.

9. Dynamic behavior

All results described in Section 9 are based on measurements of types LD6806CX4xxx

and LD6806Fxxx from the LD6806 product series within Section 6 “Recommended

operating cond itio ns ”.

9.1 Dropout

The dropout voltage is defined as the smallest input to output voltage difference at a

specified load current when the regulator operates within its linear region with the pass

transistor functioning as a plain resistor. This means that the input voltage is below the

nominal output vo ltage value .

A small dropout volt age guarantie s lower power consumption and ef ficiency maximization.

Isc short-circuit current pin OUT - 600 - mA

Iqquiescent current VEN = 1.4 V; IOUT = 0 mA - 70 100 A

VEN = 1.4V; 1mA  IOUT 200 mA - 155 250 A

VEN  0.4 V - 0.1 1.0 A

Tsd shutdown temperature - 160 - C

Tsd(hys) shutdown temperature

hysteresis [2] -20 - K

PSRR power supply rejection ratio VIN = VO(nom) + 1 V; IOUT = 30 mA;

fripple = 1 kHz [1] -55 - dB

Vn(o)(RMS) RMS output noise voltage bandwidth = 1 0 Hz to 100 kHz;

CL(ext) =1F-30 - V

tstartup(reg) regulator start-up time VIN = 5.5 V; VOUT = 0.95 VO(nom);

IOUT = 200 mA; C L(ext) =1F[1] - - 200 s

tsd(reg) regulator shutdown time VIN = 5.5 V; CL(ext) =1F[3] -300- s

Rpd pull-down resistance [3] -100- 

Table 10. Electrical characteristics …continued

At recommended input voltages and Tamb =





Cto+85



C; voltages are referenced to GND (ground = 0 V);

unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Product data sheet Rev. 3 — 9 December 2011 8 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

(1) +85 C

(2) +25 C

(3) 40 C

(1) +85 C

(2) +25 C

(3) 40 C

Fig 6. Dropout as a function of temperature for

LD6806CX4/25H Fig 7. Drop out as a function of temperat ure for

LD6806F/25H

IOUT (mA)

0 20016080 12040

001aan929

100

Vdo

(mV)

(1)

(2)

(3)

IOUT (mA)

0 20016080 12040

001aan930

100

Vdo

(mV)

(1)

(2)

(3)

(1) +85 C

(2) +25 C

(3) 40 C

(1) +85 C

(2) +25 C

(3) 40 C

Fig 8. Dropout as a function of temperature for

LD6806CX4/36H Fig 9. Drop out as a function of temperat ure for

LD6806F/36H

IOUT (mA)

0 20016080 12040

001aan935

100

Vdo

(mV)

(1)

(2)

(3)

IOUT (mA)

0 20016080 12040

001aan936

100

Vdo

(mV)

(1)

(2)

(3)

Product data sheet Rev. 3 — 9 December 2011 9 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

9.2 Output voltage variation

The guaranteed output voltages are specified in Table 10.

(1) +85 C

(2) +25 C

(3) 40 C

Fig 10. Dropout as a function of tempe rature for LD6806TD/36P

IOUT (mA)

0 20016080 12040

018aaa223

100

Vdo

(mV)

(1)

(2)

(3)

(1) IOUT =1mA

(2) IOUT = 100 mA

(3) IOUT = 200 mA

(1) IOUT =1mA

(2) IOUT = 100 mA

(3) IOUT = 200 mA

Fig 11. Output voltage variation for LD6806CX4/12H Fig 12. Output voltage variation for LD6806CX4/25H

Tamb (°C)

-60 14010020 60-20

001aan942

1.20

1.18

1.22

1.24

VOUT

(V)

1.16

(1)

(2)

(3)

Tamb (°C)

-60 14010020 60-20

001aan943

2.50

2.48

2.52

2.54

VOUT

(V)

2.46

(1)

(2)

(3)

Product data sheet Rev. 3 — 9 December 2011 10 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

9.3 Quiescent current

Quiescent or ground current is the difference between the input and the output current of

the regulator.

(1) IOUT =10mA

(2) IOUT =0mA (1) IOUT =10mA

(2) IOUT =0mA

Fig 13. Quiescent current for LD6806CX4/12H Fig 14. Quiescent current for LD6806CX4/25H

Tamb (°C)

-60 14010020 60-20

001aao106

IGND

(µA)

(1)

(2)

Tamb (°C)

-60 14010020 60-20

001aan944

IGND

(µA)

(1)

(2)

Product data sheet Rev. 3 — 9 December 2011 11 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

9.4 Noise

Output noise voltage of an LDO circu i t is given as noise density or RMS output noise

voltage o ver a defined range of fr equencies (10 Hz to 100 kHz). Permanent conditions are

a constant output curren t an d a rip ple-free input voltage. The output noise voltage is

generated by the LDO regulator.

(1) 0 mA

(2) 1 mA

(3) 50 mA

(4) 100 mA

(5) 150 mA

(6) 200 mA

(1) 0 mA

(2) 1 mA

(3) 50 mA

(4) 100 mA

(5) 150 mA

(6) 200 mA

Fig 15. Noise density for LD6806CX4/25H Fig 16. Noise density for LD6806CX4/36H

001aan941

10-1

10-2

10 105

104

102103

(1)

(2)

(3)

(4)

(5)

(6)

noise

(μV/√Hz)

frequency (Hz)

001aao104

10-1

noise

(μV/√Hz)

10-2

frequency (Hz)

10 105

104

102103

(1)

(2)

(3)

(4)

(5)

(6)

Product data sheet Rev. 3 — 9 December 2011 12 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

9.5 Line regulation

Line regulation response is the capability of the circuit to maintain the nominal output

voltage while varying the input voltage.

Regulation % VVOUT



VIN



-----------------100

VOUT

-------------

=

(1) VIN

(2) VOUT

(1) VIN

(2) VOUT

Fig 17. Line regulation for LD6806CX4/12H Fig 18. Line regulation for LD6806F/12H

time (ms)

0 0.80.60.2 0.4

001aan925

VIN

(V)

1.4

1.8

1.2

1.6

2.0

VOUT

(V)

1.0

(1)

(2)

time (ms)

0 0.2 0.4 0.6 0.70.50.30.1

001aan926

VIN

(V)

1.4

1.8

1.2

1.6

2.0

VOUT

(V)

1.0

(1)

(2)

(1) VIN

(2) VOUT

(1) VIN

(2) VOUT

Fig 19. Line regulation for LD6806CX4/25H Fig 20. Line regulation for LD6806F/25H

time (ms)

0 0.40.30.1 0.2

001aan931

VIN

(V)

2.51

2.54

2.47

2.53

2.55VOUT

(V)

2.45

2.49

2.46

2.52

2.48

2.50

(1)

(2)

time (ms)

0 0.40.30.1 0.2

001aan932

VIN

(V)

2.51

2.54

2.47

2.53

2.55VOUT

(V)

2.45

2.49

2.46

2.52

2.48

2.50

(1)

(2)

Product data sheet Rev. 3 — 9 December 2011 13 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

9.6 Load regulation

Load regulation is the capability of the circuit to maintain the nominal output voltage while

varying the output load current.

(1) VIN

(2) VOUT

(1) VIN

(2) VOUT

Fig 21. Line regulation for LD6806CX4/36H Fig 22. Line regulation for LD6806F/36H

time (ms)

0 0.80.60.2 0.4

001aan937

VIN

(V)

3.55

3.65

3.75

VOUT

(V)

3.45

(1)

(2)

time (ms)

0 0.70.60.2 0.40.1 0.3 0.5

001aan938

VIN

(V)

3.55

3.65

3.75

VOUT

(V)

3.45

(1)

(2)

Load regulation % mA

VOUT



VO nom

------------------- 100

IOUT max

-----------------------------------

(1) IOUT

(2) VOUT

(1) IOUT

(2) VOUT

Fig 23. Load regulation for LD6806 CX4/12H Fig 24. Load regulation for LD 6806F/12H

time (ms)

0 0.2 0.4 0.6 0.70.50.30.1

001aan927

0.1

0.3

0.5

IOUT

(A)

-0.1

0.9

1.2

0.7

1.1

1.3 VOUT

(V)

0.5

0.8

0.6

1.0

(1)

(2)

time (ms)

0 0.80.60.2 0.4

001aan928

0.1

0.3

0.5

IOUT

(A)

-0.1

1.10

1.25

1.00

1.20

1.30

VOUT

(V)

0.90

1.05

0.95

1.15

(1)

(2)

Product data sheet Rev. 3 — 9 December 2011 14 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

(1) IOUT

(2) VOUT

(1) IOUT

(2) VOUT

Fig 25. Load regulation for LD6806 CX4/25H Fig 26. Load regulation for LD 6806F/25H

time (ms)

0 0.40.30.1 0.2

001aan933

0.1

0.3

0.5

IOUT

(A)

-0.1

2.4

2.5

2.6

VOUT

(V)

2.3

(1)

(2)

time (ms)

0 0.40.30.1 0.2

001aan934

0.1

0.3

0.5

IOUT

(A)

-0.1

2.4

2.5

2.6

VOUT

(V)

2.3

(1)

(2)

(1) IOUT

(2) VOUT

(1) IOUT

(2) VOUT

Fig 27. Load regulation for LD6806 CX4/36H Fig 28. Load regulation for LD 6806F/36H

time (ms)

0 0.70.60.2 0.40.1 0.3 0.5

001aan939

0.1

0.3

0.5

IOUT

(A)

-0.1

3.5

3.6

3.7

VOUT

(V)

3.4

(1)

(2)

time (ms)

0 0.70.60.2 0.40.1 0.3 0.5

001aan940

0.1

0.3

0.5

IOUT

(A)

-0.1

3.5

3.6

3.7

VOUT

(V)

3.4

(1)

(2)

Product data sheet Rev. 3 — 9 December 2011 15 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

9.7 Start-up and shut down

Start-up time defines the time needed for the LDO to achieve 95 % of its typical output

voltage level after activation via the enable pin.

Shut down time defines the time needed for the LDO to pull-down the output voltage to

10% of its nominal output voltage after deactivation via the enable pin.

(1) VEN.

(2) VOUT.(1) VEN.

(2) VOUT.

Fig 29. Start-up for LD6806CX4/23H Fig 30. Shut down for LD 6806F/25P

time (ms)

0 0.20.150.05 0.1

001aan946

0.8

0.4

1.2

1.6

Venable

(V)

VOUT

(V)

0.5

1.5

2.5

(1)

(2)

time (ms)

0 0.40.30.1 0.2

001aan947

0.8

0.6

0.4

0.2

1.2

1.4

Venable

(V)

(1) (2)

VOUT

(V)

0.5

1.5

2.5

Product data sheet Rev. 3 — 9 December 2011 16 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

9.8 Power Supply Rejection Ratio (PSRR)

PSRR stands for the capability of the regulator to suppress unwanted signals on the input

voltage like noise or ripples.

for all frequencies

PSRR dB 20 Vout ripple

Vin ripple

--------------------------

log=

(1) 1 mA

(2) 50 mA

(3) 100 mA

(4) 200 mA

(1) 1 mA

(2) 50 mA

(3) 100 mA

(4) 200 mA

Fig 31. PSRR for LD6806CX4/25H Fig 32. PSRR for LD6806CX4/36H

001aan945

PSRR

(dB)

-70

frequency (Hz)

102105

104

103

-60

-50

-40

-30

-20

-10

(1)

(2)

(3)

(4)

001aao105

-40

-20

PSSR

(dB)

-60

frequency (Hz)

102105

104

103

(1)

(2)

(3)

(4)

Product data sheet Rev. 3 — 9 December 2011 17 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

9.9 Enable threshold voltage

An active HIGH signal enables the LDO when the signal exceeds th e minimum input

HIGH voltage threshold. The device is in Off state as long the signal is below the

maximum LOW threshold. The input voltage threshold is independent from the LDO

supply voltage.

(1) LOW to HIGH

(2) HIGH to LOW

Fig 33. Enable threshold voltage

VEN (V)

0.3 1.51.10.70.5 1.30.9

001aan808

1.5

0.5

2.5

3.5

VOUT

(V)

-0.5

(2) (1)

Product data sheet Rev. 3 — 9 December 2011 18 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

10. Application information

10.1 Output capacitor values

The LD6806 series requires external capacitors at the output to guarantee a stable

regulator behavior. Also an input capacitor is recommended to keep the input voltage

stable. These capacitors should not under-run the specified minimum Equivalent Series

Resistance (ESR).

The absolute value of the total capacitance attached to the output pin OUT influences the

shutdown time (tsd(reg)) of the LD6806 series.

[1] The minimum value of capacitance for stability and correct operation is 0.7 F. The capacitor tolerance

should be 30 % or better over the temperature range. The full range of operating conditions for the

capacitor in the application should be considered during device selection to ensure that this minimum

capacitance specification is met. The recommended capacitor type is X7R to meet the full device

temperature specification of 40 C to +125 C.

11. Test information

11.1 Quality information

This product has been qualified in accordance with NX2-00001 NXP Semiconductors

Quality and Reliability Specification and is suitable for use in consumer applications.

Table 11. External load capacitor

Symbol Parameter Conditions Min Typ Max Unit

CL(ext) external load capacitance [1] -1.0-F

ESR equivalent series resistance 5 - 500 m

Fig 34. Application di agram

OUT OUTIN

GND

1μF

001aan647

Product data sheet Rev. 3 — 9 December 2011 19 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

12. Package outline

Fig 35. Package outline WLCSP4

wlcsp4_2x2_po

European

projection

WLCSP4: wafer level chip-size package; 4 bumps (2 x 2)

bump A1

index area

detail X

Table 12. Dimensions of LD6806CX4/xxx for package outline WLCSP4; see Figure 35

Symbol Min Typ Max Unit

A 0.44 0.47 0.50 mm

A10.18 0.20 0.22 mm

A20.26 0.27 0.28 mm

b 0.21 0.26 0.31 mm

D 0.71 0.76 0.81 mm

E 0.71 0.76 0.81 mm

e-0.4-mm

Product data sheet Rev. 3 — 9 December 2011 20 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

Fig 36. Package outline WLCSP4 with backside coating

European

projection

bump A1

index area

WLCSP4: wafer level chip-size package with backside coating; 4 bumps (2 x 2)

detail X

wlcsp4_2x2_c_po

Table 13. Dimensions of LD6806CX4/Cxxx for package outline WLCSP4 with backside coating; see Figure 36

Symbol Min Typ Max Unit

A 0.47 0.51 0.55 mm

A10.18 0.20 0.22 mm

A20.26 0.27 0.28 mm

A30.03 0.04 0.05 mm

b 0.21 0.26 0.31 mm

D 0.71 0.76 0.81 mm

E 0.71 0.76 0.81 mm

e-0.4-mm

Product data sheet Rev. 3 — 9 December 2011 21 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

Fig 37. Package outline SOT886 (XSON6)

terminal 1

index area

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

SOT886 MO-252

SOT886

04-07-15

04-07-22

DIMENSIONS (mm are the original dimensions)

XSON6: plastic extremely thin small outline package; no leads; 6 terminals; body 1 x 1.45 x 0.5 mm

0 1 2 mm

scale

Notes

1. Including plating thickness.

2. Can be visible in some manufacturing processes.

UNIT

mm 0.25

0.17 1.5

1.4 0.35

0.27

max b E

1.05

0.95

Dee

0.40

0.32

0.50.6

A(1)

max

0.5 0.04

6×

(2)

4×

(2)

Product data sheet Rev. 3 — 9 December 2011 22 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

Fig 38. SOT753; Plastic surface-mounted package; 5 leads

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC JEITA

SOT753 SC-74A

wBM

detail X

vMA

0 1 2 mm

scale

132

Plastic surface-mounted package; 5 leads SOT753

UNIT A1bpcDEHELpQywv

mm 0.100

0.013 0.40

0.25 3.1

2.7

0.26

0.10 1.7

1.3

0.95 3.0

2.5 0.2 0.10.2

DIMENSIONS (mm are the original dimensions)

0.6

0.2 0.33

0.23

1.1

0.9

02-04-16

06-03-16

Product data sheet Rev. 3 — 9 December 2011 23 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

13. Soldering

Fig 39. Soldering footprint WLCSP4

wlcsp4_2x2_fr

solder resist

occupied area

solder paste = solderland

Dimensions in mm

(4×)

Table 14. Dimensions of soldering footprint WLCSP4; see Figure 39

Symbol Min Typ Max Unit

c - 0.25 - mm

D 0.71 0.76 0.81 mm

E 0.71 0.76 0.81 mm

e-0.4-mm

f - 0.325 - mm

Fig 40. Soldering footprint SOT886 (XSON6)

sot886_fr

solder resist

occupied area

solder paste = solderland

Dimensions in mm

0.425

(6×)

1.250

0.675

1.700

0.325

(6×)

0.270

(6×)

0.370

(6×)

0.500

Product data sheet Rev. 3 — 9 December 2011 24 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

14. Soldering of WLCSP packages

14.1 Introduction to soldering WLCSP packages

This text provides a very brief insight into a complex technology. A more in-depth account

of soldering WLCSP (Wafer Level Chip-Size Packages) can be found in application note

AN10439 “Wafer Level Chip Scale Package” and in application note AN10365 “Surface

mount reflow soldering description”.

Wave soldering is not suitable for this package.

Fig 41. SOT753 (TSOP5); Reflow soldering footprint

Fig 42. SOT753 (TSOP5); Wave soldering footprint

solder lands

solder resist

occupied area

solder paste

sot753_fr

2.8253.3

0.45

(5×)0.55

(5×)

0.7

(5×)

0.8

(5×)

3.45

1.95

0.95

2.4 Dimensions in mm

sot753_fw

5.3

5.05 0.45

1.5

(4×)

1.45

(5×)2.85

1.475

solder lands

solder resist

occupied area

preferred transport

direction during soldering

Dimensions in mm

Product data sheet Rev. 3 — 9 December 2011 25 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

All NXP WLCSP packages are lead-free.

14.2 Board mounting

Board mounting of a WLCSP requires several steps:

1. Solder paste printing on the PCB

2. Component placement with a pick and place machine

3. The reflow soldering itself

14.3 Reflow soldering

Key characteristics in reflow soldering are:

•Lead-free ve rsus SnPb soldering; note th at a lead-free reflow process usua lly leads to

higher minimum peak temperatures (see Figure 43) than a PbSn process, thus

reducing the process window

•Solder paste printing issues, such as smearing, release, and adjusting the process

window for a mix of large and small components on one board

•Reflow temperature profile; this profile includes preheat, reflow (in which the board is

heated to the peak temperature), and cooling down. It is imperative that the peak

temperature is high enoug h for the solder to make reliable solder joint s (a solder paste

characterist ic) while be ing low enou g h th at th e packages an d/ or boa rd s ar e no t

damaged. The peak temperature of the package depends on package thickness and

volume and is classified in accordance with Table 15.

Moisture sensitivity precautions, as indicated on the packing, must be respected at all

times.

Studies have shown that small packages reach higher temperatures during reflow

soldering, see Figure 43.

Table 15. Lead-free process (from J-STD-020C)

Package thickness (mm) Package reflow temperature ( C)

Volume (mm3)

< 350 350 to 2000 > 2000

< 1.6 260 260 260

1.6 to 2.5 260 250 245

> 2.5 250 245 245

Product data sheet Rev. 3 — 9 December 2011 26 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

For further information on temperature profiles, refer to application note AN10365

“Surface mount reflow soldering description”.

14.3.1 Stand off

The stand off between the substrate and the chip is determined by:

•The amount of printed solder on the substrate

•The size of the solder land on the substrate

•The bump height on the chip

The higher the stand off, the better the stresses are released due to TEC (Thermal

Expansion Coefficient) differences between substrate and chip.

14.3.2 Quality of solder joint

A flip-chip joint is considered to be a good joint when the entire solder land has been

wetted by the solder from the bump. The surface of the joint should be smooth and the

shape symmetrical. The soldered joints on a chip should be uniform. Voids in the bumps

after reflow can occur during the reflow process in bumps with high ratio of bump diameter

to bump height, i.e. low bumps with large diameter. No failures have been found to be

related to these voids. Solder joint inspection after reflow can be done with X-ray to

monitor defects such as bridging, open circuits and voids.

14.3.3 Rework

In general, rework is not recommended. By rework we mean the process of removing the

chip from the substrate and replacing it with a new chip. If a chip is remo ved from the

substrate, most solder balls of the chip will be damaged. In that case it is recommended

not to re-use the chip again.

MSL: Moisture Sensitivity Level

Fig 43. Temperature profiles for large and small components

001aac844

temperature

time

minimum peak temperature

= minimum soldering temperature

maximum peak temperature

= MSL limit, damage level

peak

temperature

Product data sheet Rev. 3 — 9 December 2011 27 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

Device removal can be done when the substrate is heated until it is certai n that all solder

joints are molten. The chip can then be carefully removed from the substrate without

damaging the tracks and solder lands on the substrate. Removing the device must be

done using plastic tweezers, because metal tweezers can damage the silicon. The

surface of the substrate should be carefully cleaned and all solder and flux residues

and/or underfill removed. When a new chip is placed on the substrate, use the flux

process instead of solder on th e solder land s. Ap ply flu x on th e bu mps at the chip side as

well as on the solder pads on the substrate. Place and align the new chip while viewing

with a microscope. To reflow the solder, use the solder profile shown in application note

AN10365 “Surface mount reflow soldering description”.

14.3.4 Cleaning

Cleaning can be done after reflow soldering.

15. Soldering of SMD packages

This text provides a very brief insight into a complex technology. A more in-depth account

of soldering ICs can be found in Application Note AN10365 “Surface mount reflow

soldering description”.

15.1 Introduction to soldering

Soldering is one of the most common methods through which packages are attached to

Printed Circuit Boards (PCBs), to form electrical circuits. The soldered joint provides both

the mechanical and the electrical connection. There is no single soldering method that is

ideal for all IC packages. Wave soldering is often preferred when through-hole and

Surface Mount Devices (SMDs) are mixed on one printed wiring board; however, it is not

suitable for fine pitch SMDs. Reflow soldering is ideal for the small pitches and high

densities that come with increased miniaturization.

15.2 Wave and reflow soldering

W ave soldering is a joinin g technology in which the joint s are made by solder coming from

a standing wave of liquid solder. The wave soldering process is suitable for the following:

•Through-hole components

•Leaded or leadless SMDs, which are glued to the surface of the printed circu it board

Not all SMDs can be wave soldered. Packages with solder balls, and some leadless

packages which have solder lands underneath the body, cannot be wave soldered. Also,

leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered,

due to an increased probability of bridging.

The reflow soldering process involves applying solder paste to a board, followed by

component placement and exposure to a temperature profile. Leaded packages,

packages with solder balls, and leadless packages are all reflow solderable.

Key characteristics in both wave and reflow soldering are:

•Board specifications, including the board finish, solder masks and vias

•Package footprints, including solder thieves and orientation

Product data sheet Rev. 3 — 9 December 2011 28 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

•The moisture sensitivity level of the packages

•Package placement

•Inspection and repair

•Lead-free soldering versus SnPb soldering

15.3 Wave soldering

Key characteristics in wave soldering are:

•Process issues, such as application of adhesive and flux, clinching of leads, board

transport, the solder wave parameters, and the time during which components are

exposed to the wave

•Solder bath specifications, including temperature and impurities

15.4 Reflow soldering

Key characteristics in reflow soldering are:

•Lead-free ve rsus SnPb soldering; note th at a lead-free reflow process usua lly leads to

higher minimum peak temperatures (see Figure 44) than a SnPb process, thus

reducing the process window

•Solder paste printing issues including smearing, release, and adjusting the process

window for a mix of large and small components on one board

•Reflow temperature profile; this profile includes preheat, reflow (in which the board is

heated to the peak temperature) and cooling down. It is imperative that the peak

temperature is high enoug h for the solder to make reliable solder joint s (a solder paste

characteristic). In addition, the peak temperature must be low enough that the

packages and/or boards are not damaged. The peak temperature of the package

depends on package thickness and volume and is classified in accordance with

Table 16 and 17

Moisture sensitivity precautions, as indicated on the packing, must be respected at all

times.

Table 16. SnPb eutectic process (from J-STD-020C)

Package thickness (mm) Package reflow temperature ( C)

Volume (mm3)

< 350  350

< 2.5 2 35 220

 2.5 220 220

Table 17. Lead-free process (from J-STD-020C)

Package thickness (mm) Package reflow temperature ( C)

Volume (mm3)

< 350 350 to 2000 > 2000

< 1.6 260 260 260

1.6 to 2.5 260 250 245

> 2.5 250 245 245

Product data sheet Rev. 3 — 9 December 2011 29 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

Studies have shown that small packages reach higher temperatures during reflow

soldering, see Figure 44.

For further information on temperature profiles, refer to Application Note AN10365

“Surface mount reflow soldering description”.

16. Mounting

16.1 PCB design guidelines

It is recommended, for optimum performance, to use a Non-Solder Mask Defined

(NSMD), also known as a copper-defined design, incorporating laser-drilled micro-vias

connecting the ground pads to a buried ground-plane layer. This results in the lowest

possible ground inductance and provides the best high frequency and ESD performance.

Refer to Table 18 for the recommended PCB design parameters.

MSL: Moisture Sensitivity Level

Fig 44. Temperature profiles for large and small components

001aac844

temperature

time

minimum peak temperature

= minimum soldering temperature

maximum peak temperature

= MSL limit, damage level

peak

temperature

Table 18. Recommended PCB design parameters

Parameter Value or specification

PCB pad diameter 250 m

Micro-via diameter 100 m (0.004 inch)

Solder mask aperture diameter 325 m

Copper thickness 20 m to 40 m

Copper finish AuNi or OSP

PCB material FR4

Product data sheet Rev. 3 — 9 December 2011 30 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

16.2 PCB assembly guidelines for Pb-free soldering

Table 19. Assembly recommen dations

Parameter Value or specification

Solder screen aperture diameter 250 m

Solder screen thickness 100 m (0.004 inch)

Solder paste: Pb-free SnAg (3 % to 4 %); Cu (0.5 % to 0.9 %)

Solder to flux ratio 50 : 50

Solder reflow profile see Figure 45

The device is capable of withstanding at least three reflows at this profile.

Fig 45. Pb-free solder refl ow profile

Table 20. Characteristics

Symbol Parameter Conditions Min Typ Max Unit

Treflow(peak) peak reflow temperature 230 - 260 C

t1time 1 soak time 60 - 180 s

t2time 2 time during T 250 C--30s

t3time 3 time during T 230 C10-50s

t4time 4 time durin g T > 217 C 30 - 150 s

t5time 5 - - 540 s

dT/dt rate of change of

temperature cooling rate - - 6C/s

preheat 2.5 - 4.0 C/s

001aai943

Treflow(peak)

250

230

217

(°C)

cooling rate

preheat

t2t (s)

Product data sheet Rev. 3 — 9 December 2011 31 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

17. Abbreviations

18. References

[1] IEC 60134 — Rating systems for electronic tubes and valves and analogous

semiconductor devices

[2] IEC 61340-3-1 — Methods for simulation of electrostatic effects - Hu man body

model (HBM) electrostatic discharge test waveforms

[3] JESD22-A115C — Electrostatic discharg e (ESD) Sensitivity Testing Machine

Model (MM)

[4] NX2-00001 — NXP Semiconductors Quality and Reliability Specification

[5] AN10439 — Wafer Level Chip Size Package

[6] AN10365 — Surface mount reflow soldering description

Table 21. Abbreviations

Acronym Description

CSP Chip-Size Package

DUT Device Under Test

EMI ElectroMagnetic Interference

ESD ElectroStatic Discharge

FR4 Flame Retard 4

HBM Human Body Model

LDO Low DropOut

MM Machine Model

NSMD Non-Solder Mask Design

OSP Organic Solderability Preservation

PCB Printed-Circuit Board

PSRR Power Supply Rejection Ratio

PSU Power Supply Unit

QRS Quality and Reliability Specification

RMS Root Mean S qu a re

WLCSP Wafer Level Chip-Si ze Packa ge

Product data sheet Rev. 3 — 9 December 2011 32 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

19. Revision history

Table 22. Revision history

Document ID Release date Data sheet status Change notice Supersedes

LD6806_SER v.3 20111209 Product data sheet - LD6806_SER v.2

Modifications: •WLCSP4 package with backside coating added

•SOT753 package added

•Subtype LD6806x/xxP introduced

•Minor text changes

LD6806_SER v.2 20110719 Product data sheet - LD6806_SER v.1

Modifications: •Descriptive title updated

•Table 5: title changed

•Table 10: three parameters updated

•Table 3: pin number updated

•Section 9.4 and Section 9.8 drawings updated

•Section 16: values updated

•Minor text changes

LD6806_SER v.1 20110516 Preliminary data sheet - -

Product data sheet Rev. 3 — 9 December 2011 33 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

20. Legal information

20.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term ‘short data sheet’ is explained in section “Definitions”.

[3] The product status of device (s) descr ibed in th is docume nt may have cha nged since this docume nt was publis hed and ma y dif fer in case of multiple devices. The latest product status

information is available on the Internet at URL http://www.nxp.com.

20.2 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liab ility for the consequences of

use of such information.

Short data sheet — A short dat a sheet is an extract from a full data sheet

with the same product type number(s) and tit le. A short data sh eet is intended

for quick reference only and shou ld not be rel ied u pon to cont ain det ailed and

full information. For detailed and full information see the relevant full dat a

sheet, which is available on request via the local NXP Semiconductors sales

office. In case of any inconsistency or conf lict with the short data sheet, the

full data sheet shall pre vail.

Product specificat io n — The information and data provided in a Product

data sheet shall define the specification of the product as agr eed between

NXP Semiconductors and its customer, unless NXP Semiconductors and

customer have explicitly agreed otherwise in writing. In no event however,

shall an agreement be valid in which the NXP Semiconductors product is

deemed to off er functions and qualities beyond those described in the

Product data sheet.

20.3 Disclaimers

Limited warr a nty and liability — Information in this document is believed to

be accurate and reliable. However, NXP Semiconductors does not give any

representations or warranties, expressed or implied, as to the accuracy or

completeness of such information and shall have no liability for the

consequences of use of such information.

In no event shall NXP Semiconductors be liable for any indirect, incidental ,

punitive, special or consequ ential damages (including - wit hout limitatio n - lost

profits, lost savings, business interruption, costs related to the removal or

replacement of any products or rework charges) whether or not such

damages are based on tort (including negligence), warranty, breach of

contract or any other legal theory.

Notwithstanding any damages that customer might incur for any reason

whatsoever, NXP Semiconductors’ aggreg ate and cumulative liabil ity towards

customer for the products described herein shall be limited in accordance

with the Terms and conditions of commercial sale of NXP Semiconductors.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all informa tion supplied prior

to the publication hereof .

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suit able for use in life support, life-crit ical or

safety-critical systems or equipment, nor in applications where failure or

malfunction of an NXP Semiconductors pro duct can reasonably be expected

to result in perso nal injury, death or severe property or environmental

damage. NXP Semiconductors accepts no liab ility for inclusion and/or use of

NXP Semiconductors products in such equipment or applications and

therefore such inclusion and/or use is at the customer’s own risk.

Applications — Applications that are described herein for any of these

products are for il lustrative purposes only. NXP Semiconductors makes no

representation or warranty tha t such application s will be suitable for the

specified use without further testing or modification.

Customers are responsible for the design and ope ration of their applications

and products using NXP Semiconductors product s, and NXP Semiconductors

accepts no liability for any assistance with applications or customer product

design. It is customer’s sole responsibility to determine whether the NXP

Semiconductors product is suit able and fit for the custome r’s applications and

products planned, as well as fo r the planned application and use of

customer’s third party customer(s). Customers should provide appropriate

design and operating safeguards to minimize the risks associated with their

applications and products.

NXP Semiconductors does not accept any liabili ty related to any default,

damage, costs or problem which is based on any weakness or default in the

customer’s applications or products, or the application or use by customer’s

third party customer(s). Customer is responsible for doing all necessa ry

testing for th e customer’s applications and pro ducts using NXP

Semiconductors products in order to avoid a default of the applications and

the products or of the application or use by cust omer’s third party

customer(s). NXP does not accept any liability in this respect.

Limiting values — Stress above one or more limiting values (as defined in

the Absolute Maximum Ratings System of IEC 60134) will cause permanent

damage to the device. Limiting values are stress ratings only and (proper)

operation of the device at these or any other conditions above those given in

the Recommended operating conditions section (if present) or the

Characteristics sections of this document is not warranted. Constant or

repeated exposure to limiting values will permanent ly and irreversibly affect

the quality and reliability of the device.

Terms and conditions of commercial sale — NXP Semiconductors

products are sold subject to the general terms and conditions of commercial

sale, as published at http://www.nxp.com/profile/terms, unless otherwise

agreed in a valid written individua l agreement. In case an individual

agreement is concluded only the ter ms and conditions of the respective

agreement shall apply. NXP Semiconductors hereby expressly objects to

applying the customer’s general terms and conditions with regard to the

purchase of NXP Semiconductors products by customer.

No offer to sell or license — Not hing in this document may be interpret ed or

construed as an of fer t o sell product s that is open for accept ance or t he grant,

conveyance or implication of any license under any copyri ghts, paten ts or

other industrial or intellectual property rights.

Export control — This document as well as the item(s) described herein

may be subject to export control regulatio ns. Export might require a prior

authorization from competent authorities.

Document status[1][2] Product status[3] Definition

Objective [short] data sheet Development This document contains data from the objective specification for product development.

Preliminary [short] dat a sheet Qualification This document contains data from the preliminary specification.

Product [short] dat a sheet Production This document contains the product specification.

Product data sheet Rev. 3 — 9 December 2011 34 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

Non-automotive qualified products — Unless this data sheet expressly

states that this specific NXP Semiconductors product is automotive qualified,

the product is not suitable for aut omo tive use. It i s neit her qua lif ied nor tested

in accordance with automotive testing or application requirements. NXP

Semiconductors accepts no liability for inclusion and/or use of

non-automotive qualified products in automotive equipment or applications.

In the event that customer uses the product for design-in and use in

automotive applications to automot ive specifications and standard s, customer

(a) shall use the product without NXP Semiconductors’ warranty of the

product for such automotive applications, use and specifications, and (b)

whenever cust omer uses the product for automotive applications beyond

NXP Semiconductors’ specifications such use shall be solely at customer’s

own risk, and (c) customer fully indemnifies NXP Semiconductors for any

liability, damages or failed product cl aims resulting from custome r design and

use of the product for automotive applications beyond NXP Semiconductors’

standard warranty and NXP Semiconductors’ product specif ications.

20.4 Trademarks

Notice: All refe renced brands, produc t names, service names and trademarks

are the property of their respect i ve ow ners.

21. Contact information

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Product data sheet Rev. 3 — 9 December 2011 35 of 36

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

22. Tables

Table 1. Pin description for SOT753 . . . . . . . . . . . . . . . .2

Table 2. Pin description for WLCSP4. . . . . . . . . . . . . . . .2

Table 3. Pin description for SOT886 . . . . . . . . . . . . . . . .2

Table 4. Ordering information . . . . . . . . . . . . . . . . . . . . .3

Table 5. Type number and nominal output voltage of

high-ohmic output . . . . . . . . . . . . . . . . . . . . . . .3

Table 6. Type number and nominal output voltage of

low.ohmic output . . . . . . . . . . . . . . . . . . . . . . . .3

Table 7. Limiting values . . . . . . . . . . . . . . . . . . . . . . . . . .5

Table 8. Operating conditions . . . . . . . . . . . . . . . . . . . . .5

Table 9. Thermal characteristics . . . . . . . . . . . . . . . . . . .6

Table 10. Electrical characteristics . . . . . . . . . . . . . . . . . .6

Table 11. External load capacitor. . . . . . . . . . . . . . . . . . .18

Table 12. Dimensions of LD6806CX4/xxx for package

outline WLCSP4 ; s ee Figure 35 . . . . . . . . . . . 19

Table 13. Dimensions of LD6806CX4/Cxxx for package

outline WLCSP4 with backside coating;

see Figure 36 . . . . . . . . . . . . . . . . . . . . . . . . . 20

Table 14. Dimensions of soldering footprint WLCSP4;

see Figure 39 . . . . . . . . . . . . . . . . . . . . . . . . . 23

Table 15. Lead-free process (from J-STD-020C) . . . . . . 25

Table 16. SnPb eutectic pr oce ss (fro m J-STD -0 2 0C) . . . 28

Table 17. Lead-free process (from J-STD-020C) . . . . . . 28

Table 18. Recommended PCB design parameters . . . . 29

Table 19. Assembly recommendations . . . . . . . . . . . . . . 30

Table 20. Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 30

Table 21. Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 31

Table 22. Revision history . . . . . . . . . . . . . . . . . . . . . . . . 32

23. Figures

Fig 1. Configuration for SOT753 . . . . . . . . . . . . . . . . . . .2

Fig 2. Configuration for WLCSP4 . . . . . . . . . . . . . . . . . .2

Fig 3. Configuration for SOT886 . . . . . . . . . . . . . . . . . . .2

Fig 4. Block diagram of LD6806x/xxH . . . . . . . . . . . . . . .4

Fig 5. Block diagram of LD6806x/xxP . . . . . . . . . . . . . . .4

Fig 6. Dropout as a function of temperature for

LD6806CX4/25H . . . . . . . . . . . . . . . . . . . . . . . . . .8

Fig 7. Dropout as a function of temperature for

LD6806F/25H . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Fig 8. Dropout as a function of temperature for

LD6806CX4/36H . . . . . . . . . . . . . . . . . . . . . . . . . .8

Fig 9. Dropout as a function of temperature for

LD6806F/36H . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Fig 10. Dropout as a function of temperature for

LD6806TD/36P . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Fig 11. Ou tput voltage variation for LD6806CX4/12H . . . .9

Fig 12. Outp ut voltage variation for LD6806CX4/25H . . . .9

Fig 13. Quiescent current fo r LD6806CX4/12H. . . . . . . .10

Fig 14. Quiescent current fo r LD6806CX4/25H. . . . . . . .10

Fig 15. Noise density for LD6806 CX4/25H . . . . . . . . . . .11

Fig 16. Noise density for LD6806 CX4/36H . . . . . . . . . . .11

Fig 17. Line regulation for LD6806CX4/12H . . . . . . . . . .12

Fig 18. Line regulation for LD6806F/12H. . . . . . . . . . . . .12

Fig 19. Line regulation for LD6806CX4/25H . . . . . . . . . .12

Fig 20. Line regulation for LD6806F/25H. . . . . . . . . . . . .12

Fig 21. Line regulation for LD6806CX4/36H . . . . . . . . . .13

Fig 22. Line regulation for LD6806F/36H. . . . . . . . . . . . .13

Fig 23. Load regulation for LD68 06CX4/12H. . . . . . . . . .13

Fig 24. Load regulation for LD68 06F/12H . . . . . . . . . . . .13

Fig 25. Load regulation for LD68 06CX4/25H. . . . . . . . . .14

Fig 26. Load regulation for LD68 06F/25H . . . . . . . . . . . .14

Fig 27. Load regulation for LD68 06CX4/36H. . . . . . . . . .14

Fig 28. Load regulation for LD68 06F/36H . . . . . . . . . . . .14

Fig 29. Start-up for LD6806CX4/23H. . . . . . . . . . . . . . . .15

Fig 30. Shut down for LD6806F/25P . . . . . . . . . . . . . . . .15

Fig 31. PSRR for LD6806CX4/25H . . . . . . . . . . . . . . . .16

Fig 32. PSRR for LD6806CX4/36H . . . . . . . . . . . . . . . .16

Fig 33. Enable threshold voltage . . . . . . . . . . . . . . . . . . .17

Fig 34. Application diagram. . . . . . . . . . . . . . . . . . . . . . . 18

Fig 35. Package outline WLCSP4. . . . . . . . . . . . . . . . . . 19

Fig 36. Package outline WLCSP4 with ba ckside

coating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Fig 37. Package outline SOT886 (XSON6). . . . . . . . . . . 21

Fig 38. SOT753; Plastic surface-mounted package;

5 leads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Fig 39. Soldering footprint WLCSP4 . . . . . . . . . . . . . . . . 23

Fig 40. Soldering footprint SOT886 (XSON6). . . . . . . . . 23

Fig 41. SOT753 (TSOP5); Reflow sol dering footprint. . . 24

Fig 42. SOT753 (TSOP5); Wave soldering footprint. . . . 24

Fig 43. Temperature profiles for large and small

components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Fig 44. Temperature profiles for large and small

components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Fig 45. Pb-free solder reflow profile . . . . . . . . . . . . . . . . 30

NXP Semiconductors LD6806 series

Ultra low-dropout regulator, low noise, 200 mA

For more information, please visit: http://www.nxp.co m

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 9 December 2011

Document identifier: LD6806_SER

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section ‘Legal information’.

24. Contents

1 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 General description . . . . . . . . . . . . . . . . . . . . . 1

1.2 Features and benefits. . . . . . . . . . . . . . . . . . . . 1

1.3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2 Pinning information. . . . . . . . . . . . . . . . . . . . . . 2

2.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 2

3 Ordering information. . . . . . . . . . . . . . . . . . . . . 3

3.1 Ordering options. . . . . . . . . . . . . . . . . . . . . . . . 3

4 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4

5 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5

6 Recommended operating conditions. . . . . . . . 5

7 Thermal characteristics . . . . . . . . . . . . . . . . . . 6

8 Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 6

9 Dynamic behavior . . . . . . . . . . . . . . . . . . . . . . . 7

9.1 Dropout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

9.2 Output voltage variation . . . . . . . . . . . . . . . . . . 9

9.3 Quiescent current. . . . . . . . . . . . . . . . . . . . . . 10

9.4 Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

9.5 Line regulation . . . . . . . . . . . . . . . . . . . . . . . . 12

9.6 Load regulation. . . . . . . . . . . . . . . . . . . . . . . . 13

9.7 Start-up and shut down. . . . . . . . . . . . . . . . . . 15

9.8 Power Supply Rejection Ratio (PSRR). . . . . . 16

9.9 Enable threshold voltage . . . . . . . . . . . . . . . . 17

10 Application information. . . . . . . . . . . . . . . . . . 18

10.1 Output capacitor values . . . . . . . . . . . . . . . . . 18

11 Test information. . . . . . . . . . . . . . . . . . . . . . . . 18

11.1 Quality information . . . . . . . . . . . . . . . . . . . . . 18

12 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 19

13 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

14 Soldering of WLCSP packages. . . . . . . . . . . . 24

14.1 Introduction to soldering WLCSP packages. . 24

14.2 Board mounting . . . . . . . . . . . . . . . . . . . . . . . 25

14.3 Reflow soldering. . . . . . . . . . . . . . . . . . . . . . . 25

14.3.1 Stand off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

14.3.2 Quality of solder joint . . . . . . . . . . . . . . . . . . . 26

14.3.3 Rework . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

14.3.4 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

15 Soldering of SMD packages . . . . . . . . . . . . . . 27

15.1 Introduction to soldering . . . . . . . . . . . . . . . . . 27

15.2 Wave and reflow soldering . . . . . . . . . . . . . . . 27

15.3 Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 28

15.4 Reflow soldering. . . . . . . . . . . . . . . . . . . . . . . 28

16 Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

16.1 PCB design guidelines. . . . . . . . . . . . . . . . . . 29

16.2 PCB assembly guidelines for Pb-free

soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

17 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 31

18 References. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

19 Revision history . . . . . . . . . . . . . . . . . . . . . . . 32

20 Legal information . . . . . . . . . . . . . . . . . . . . . . 33

20.1 Data sheet status. . . . . . . . . . . . . . . . . . . . . . 33

20.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

20.3 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . 33

20.4 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 34

21 Contact information . . . . . . . . . . . . . . . . . . . . 34

22 Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

23 Figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

24 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36