General Description
Maxim’s DG300–DG303 and DG300A–DG303A CMOS
dual and quad analog switches combine low power
operation with fast switching times and superior DC and
AC switch characteristics. On-resistance is less than
50Ωand is essentially constant over the analog signal
range. Device specifications are ideal for battery-
powered circuitry.
These switches are available in a variety of formats as
outlined in the Pin Configurations section. The switch
control logic inputs are fully TTL and CMOS compati-
ble. Also featured are “break-before-make” switching
and low charge injection.
Maxim’s DG300-DG303 and DG300A-DG303A families
are electrically compatible and pin compatible with the
original manufacturer’s devices. All devices operate with
power supplies ranging from ±5V to ±18V. Single-sup-
ply operation is implemented by connecting V- to GND.
Applications
Portable Instruments
Low-Power Sample/Holds
Power-Supply Switching
Programmable Gain Amplifiers
SPDT and DPDT Functions
Process Control and Telemetry
Features
♦Monolithic Low-Power CMOS
♦Latchup Proof Construction
♦Fully Compatible 2nd Source
♦Low On-Resistance, <50Ω
♦Fast Switching Time
♦V+ to V- Analog Signal Range
♦Single-Supply Capability
DG300(A)/DG301(A)/DG302(A)/DG303(A)
TTL Compatible CMOS Analog Switches
________________________________________________________________ Maxim Integrated Products 1
V+
D2
N.C.
S2
S1
N.C.
D1
N.C. 14
13
12
11
10
9
8
1
2
3
4
5
6
7
N.C.
IN2
V-GND
IN1
N.C.
10
1
2
3
456
7
8
9
D1
S1
IN1
N.C.
GND
1
0
LOGIC
ON
OFF
SWITCH
DUAL SPST DG300/DG300A DUAL DPST DG302/DG302A
V+ (SUBSTRATE AND CASE)
V-
IN2
S2
D2
V+
S4
D4
D2
D1
D3
S3
N.C.
S2
IN2
V-GND
IN1
S1
DUAL SPDT DG303/DG303A
V+
S4
D4
D2
D1
D3
S3
N.C.
S2
IN2
V-GND
IN1
S1
1
0
LOGIC
ON
OFF
SWITCH
V+
D2
N.C.
S2
S1
N.C.
D1
N.C.
N.C.
N.C.
V-
SWITCH STATES ARE FOR LOGIC "1" INPUTS (POSITIVE LOGIC).
GND
IN
N.C.
10
1
2
3
456
7
8
9
D1
S1
IN
N.C.
GND
1
0
LOGIC
ON
OFF
SWITCH 1
OFF
ON
SWITCH 2
SPDT DG301/DG301A
V+ (SUBSTRATE AND CASE)
V-
N.C.
S2
D2
1
0
LOGIC
ON
OFF
SWITCHES 1, 2
OFF
ON
SWITCHES 3, 4
14
13
12
11
10
9
8
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1
2
3
4
5
6
7
Pin Configurations
Ordering Information
19-0309; Rev 3; 11/07
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
Ordering Information continued at end of data sheet.
PART TEMP RANGE PIN-PACKAGE
DG300C/D 0°C to +70°C Dice
DG300CJ 0°C to +70°C
14 Lead Plastic DIP
DG300CWE 0°C to +70°C 16 Lead Wide SO
DG300CK 0°C to +70°C 14 Lead CERDIP
DG300BWE -25°C to +85°C 16 Lead Wide SO
DG300BK -25°C to +85°C 14 Lead CERDIP
DG300BA -25°C to +85°C
10 Lead Metal Can
DG300AK -55°C to +125°C 14 Lead CERDIP
DG300AA -55°C to +125°C
10 Lead Metal Can
DG300(A)/DG301(A)/DG302(A)/DG303(A)
TTL Compatible CMOS Analog Switches
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V+ = +15V, V- = -15V, GND = 0V, TA= +25°C, unless otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Voltages Referenced to V-
V+ (DG300–DG303)...............................................................36V
V+ (DG300A–DG303A) ..........................................................44V
GND .......................................................................................25V
Digital Inputs, VS, VD, (Note 1).......................-4V to (V+ + 4V) or
30mA, whichever occurs first
Current, Any Terminal Except S or D ..................................30mA
Continuous Current, S or D .................................................30mA
(pulsed at 1ms, 10% duty cycle max) ..........................100mA
Storage Temperature (A & B suffix)...................-65°C to +150°C
(C suffix).........................-65°C to +125°C
Operating Temperature (A suffix)......................-55°C to +125°C
(B suffix)........................-25°C to +85°C
(C suffix)...........................0°C to +70°C
Lead Temperature (soldering 10s) ..................................+300°C
Power Dissipation*
Cerdip (K) (derate 11mW/°C above +75°C) ....................825mW
Plastic DIP (J) (derate 6.5mW/°C above +25°C) .............470mW
Metal Can (A) (derate 6mW/°C above +75°C).................450mW
*Device mounted with all leads soldered or welded to PC board.
DG300–DG303A
DG300A–DG303AA
DG300–DG303B/C
DG300A–DG303AB/C
PARAMETER
SYMBOL
TEST CONDITIONS MIN
(Note 2)
TYP
(Note 3)
MAX
MIN
(Note 2)
TYP
(Note 3)
MAX
UNITS
Analog Signal Range VANALOG
IS = 10mA, VIN = 0.8V or 4.0V
-15 +15 -15 +15
V
IS = -10mA, VD = 10V 30
50
30 50
Drain-Source
ON-Resistance
RDS
(
ON
)
IS = -10mA, VD = -10V 30
50
30 50
Ω
VS = 14V, VD = -14V
0.1
1
0.1
5
Source OFF-
Leakage Current
IS
(
OFF
)
VS = -14V, VD = 14V -1
-0.1
-5
-0.1
nA
VS = -14V, VD = 14V
0.1
1
0.1
5
Drain OFF-
Leakage Current
ID
(
OFF
)
VS = 14V, VD = -14V -1
-0.1
-5
-0.1
nA
VD = VS = 14V
0.1
2
0.1
5
SWITCH
Drain ON-
Leakage Current
ID
(
ON
)
VIN = 0.8V
or
VIN = 0.8V
VD = VS = -14V -2
-0.1
-5
-0.1
nA
VIN = 5.0V -1
-0.001
-1
-0.001
Input Current/
Voltage High IINH VIN = 15V
0.001
1
0.001
1
µA
INPUT
Input Current/
Voltage Low IINL VIN = 0V -1
-0.001
-1
-0.001
µA
Turn-ON Time tON
150 300 150 300
ns
Turn-OFF Time tOFF See Switching Time Test Circuit
130 250 130 250
ns
Break-Before-Make
Interval
tON - tOFF
See Break-Before-Make Time Test
Circuit, DG301(A)/DG303(A) only
50 50
ns
Charge Injection Q
CL = 10nF, RGEN = 0Ω, VGEN = 0V 12 12
pC
Source OFF-
Capacitance
CS
(
OFF
)
VS = 0V
14 14
pF
Drain OFF-
Capacitance
CD
(
OFF
)
VD = 0V
14 14
pF
Channel ON-
Capacitance
CD(ON) +
CS
(
ON
)
f = 1MHz,
VIN = 0.8V
or
VIN = 4.0V
VS = VD = 0V
40 40
pF
VIN = 0V 6 6
Input Capacitance CIN f = 1MHz VIN = 15V 7 7
pF
Off-Isolation (Note 4) 62 62
dB
DYNAMIC
Crosstalk
(Channel-to-Channel)
VIN = 0V, RL = 1kΩ
VS = 1VRMS, f = 500kHz
74 74
dB
DG300(A)/DG301(A)/DG302(A)/DG303(A)
TTL Compatible CMOS Analog Switches
_______________________________________________________________________________________ 3
ELECTRICAL CHARACTERISTICS (continued)
(V+ = +15V, V- = -15V, GND = 0V, TA= +25°C, unless otherwise noted.)
DG300–DG303A
DG300A–DG303AA
DG300–DG303B/C
DG300A–DG303AB/C
PARAMETER
SYMBOL
TEST CONDITIONS MIN
(Note 2)
TYP
(Note 3)
MAX
MIN
(Note 2)
TYP
(Note 3)
MAX
UNITS
Positive Supply
Current I+
0.23 0.5 0.23 0.5
mA
Negative Supply
Current I-
VIN = 4V (one input)
(all others = 0)
-10 -0.001 -10 -0.001
µA
Positive Supply
Current I+
0.001
10
0.001 10
µA
SUPPLY
Negative Supply
Current I-
VIN = 0.8V (all inputs)
-10 -0.001 -10 -0.001
µA
ELECTRICAL CHARACTERISTICS (Over Temperature)
(V+ = +15V, V- = -15V, GND = 0V, TA= Over Temperature Range, unless otherwise noted.)
DG300–DG303A
DG300A–DG303AA
DG300–DG303B/C
DG300A–DG303AB/C
PARAMETER
SYMBOL
TEST CONDITIONS MIN
(Note 2)
TYP
(Note 3)
MAX
MIN
(Note 2)
TYP
(Note 3)
MAX
UNITS
Analog Signal Range VANALOG
IS = -10mA, VIN = 0.8V or 4.0V
-15 +15 -15 +15
V
IS = -10mA, VD = 10V
75
75
Drain-Source
ON-Resistance
RDS
(
ON
)
IS = -10mA, VD = -10V
75
75
Ω
VS = 14V, VD = -14V
100 100
Source OFF-
Leakage Current
IS
(
OFF
)
VS = -14V, VD = 14V
-100 -100
nA
VS = -14V, VD = 14V
100 100
Drain OFF-
Leakage Current
ID
(
OFF
)
VS = 14V, VD = -14V
-100 -100
nA
VD = VS = 14V
200 200
SWITCH
Drain ON-
Leakage Current
ID
(
ON
)
VIN = 0.8V
or
VIN = 0.8V
VD = VS = -14V
-200 -200
nA
VIN = 5.0V -1
-10
Input Current/
Voltage High IINH VIN = 15V 1
10
µA
INPUT
Input Current/
Voltage Low IINL VIN = 0V -1
-10
µA
Positive Supply
Current I+ 1 1
mA
Negative Supply
Current I-
VIN = 4V (one input)
(all others = 0)
-100 -200
mA
Positive Supply
Current I+
100 200
µA
SUPPLY
Negative Supply
Current I-
VIN = 0.8V (all inputs)
-100 -200
µA
Turn-ON Time tON
500
ns
DYNAMIC
Turn-OFF Time tOFF
See Switching Time Test Circuit
450
ns
DG300(A)/DG301(A)/DG302(A)/DG303(A)
TTL Compatible CMOS Analog Switches
4 _______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS (Over Temperature) (continued)
(V+ = +15V, V- = -15V, GND = 0V, TA= Over Temperature Range, unless otherwise noted.)
Note 1: Signals on SX, DX, or INXexceeding V+ or V- are clamped by internal diodes. Limit diode forward current to maximum cur-
rent ratings.
Note 2: The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum is used
in this data sheet.
Note 3: Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
Note 4: OFF-isolation = 20 log VS, VS= input to OFF switch, VD= output.
VD
Typical Operating Characteristics
(TA= +25°C, unless otherwise noted.)
DG300(A)/DG301(A)/DG302(A)/DG303(A)
TTL Compatible CMOS Analog Switches
_______________________________________________________________________________________ 5
Figure 3. Switching Time Test Circuit
Figure 2. Break-Before-Make Time Test Circuit SPDT (DG301(A), DG303(A)
Figure 1. Charge Injection Test Circuit
Test Circuits
DG300(A)/DG301(A)/DG302(A)/DG303(A)
Applications Information
All DG300 family switches will operate with ±5V to ±15V
power supplies. They can also be used with single-ended
power supplies ranging from +10V to +30V where the V-
terminal is connected to ground. In either case, analog
signals ranging from V+ to V- can be switched.
The on-resistance variation with analog signal and supply
voltage is shown in the Typical Operating Characteristics.
The temperature coefficient of RON is typically 0.5%/°C.
Typical on-resistance matching from channel to chan-
nel is 10%. In addition, Table 1 outlines some typical
parameters for single-supply operation.
The charge injection test circuit is shown in Figure 1.
Table 2 lists the typical injected charge for DG300 series
switches with various input voltages.
TTL Compatible CMOS Analog Switches
6 _______________________________________________________________________________________
Table 1. Typical Single Supply Parameters
V+ SUPPLY VOLTAGE (V- = 0V)
PARAMETER +10V +15V +20V +30V
tON 190ns 150ns 110ns 70ns
Switching Time (RL = 1kΩ)tOFF 40ns 40ns 40ns 40ns
VSIGNAL = +1V 71Ω51Ω42Ω31Ω
VSIGNAL = V+ / 2 77Ω54Ω43Ω30ΩOn-Resistance
VSIGNAL = V+ 84Ω63Ω54Ω43Ω
Input Logic Levels 0.8V, 4.0V 0.8V, 4.0V 0.8V, 4.0V 0.8V, 4.5V
Table 2. Charge Injection (±15V Supplies)
ANALOG INPUT (V) INJECTED Q (pC)
+10 4
+5 8
012
-5 8
-10 5
Chip Topography
DIE PAD
DG300
DG300A
DG301
DG301A
DG302/DG303
DG302A/DG303A
a N.C. N.C. S3
bD1D1 D3
cN.C.S1 D1
dS1N.C. S1
e IN1 IN1 IN1
f N.C. N.C. N.C.
g GND GND GND
hV-V- V-
i IN2 N.C. IN2
jS2N.C. S2
k N.C. N.C. D2
lD2S2 D4
mN.C.D2 S4
nV+V+ V+
banm
l
k
j
c
d
efgh i
0.108"
2.74mm
0.106"
2.69mm
DG300(A)/DG301(A)/DG302(A)/DG303(A)
TTL Compatible CMOS Analog Switches
_______________________________________________________________________________________ 7
Ordering Information (continued)
PART TEMP RANGE PIN-PACKAGE
DG300AC/D 0°C to +70°C Dice
DG300ACJ 0°C to +70°C
14 Lead Plastic DIP
DG300ACWE 0°C to +70°C 16 Lead Wide SO
DG300ACK 0°C to +70°C 14 Lead CERDIP
DG300ABWE -25°C to +85°C 16 Lead Wide SO
DG300ABK -25°C to +85°C 14 Lead CERDIP
DG300ABA -25°C to +85°C
10 Lead Metal Can
DG301C/D 0°C to +70°C Dice
DG301CJ 0°C to +70°C
14 Lead Plastic DIP
DG301CWE 0°C to +70°C 16 Lead Wide SO
DG301CK 0°C to +70°C 14 Lead CERDIP
DG301BWE -25°C to +85°C 16 Lead Wide SO
DG301BK -25°C to +85°C 14 Lead CERDIP
DG301BA -25°C to +85°C
10 Lead Metal Can
DG301AK -55°C to +125°C 14 Lead CERDIP
DG301AA -55°C to +125°C
10 Lead Metal Can
DG301AC/D 0°C to +70°C Dice
DG301ACJ 0°C to +70°C
14 Lead Plastic DIP
DG301ACWE 0°C to +70°C 16 Lead Wide SO
DG301ACK 0°C to +70°C 14 Lead CERDIP
DG301ABWE -25°C to +85°C 16 Lead Wide SO
DG301ABK -25°C to +85°C 14 Lead CERDIP
DG301ABA -25°C to +85°C
10 Lead Metal Can
DG302C/D 0°C to +70°C Dice
DG302CJ 0°C to +70°C
14 Lead Plastic DIP
PART TEMP RANGE PIN-PACKAGE
DG302CWE 0°C to +70°C 16 Lead Wide SO
DG302CK 0°C to +70°C 14 Lead CERDIP
DG302BWE -25°C to +85°C 16 Lead Wide SO
DG302BK -25°C to +85°C 14 Lead CERDIP
DG302AK -55°C to +125°C 14 Lead CERDIP
DG302AC/D 0°C to +70°C Dice
DG302ACJ 0°C to +70°C 14 Lead Plastic DIP
DG302ACWE 0°C to +70°C 16 Lead Wide SO
DG302ACK 0°C to +70°C 14 Lead CERDIP
DG302ABWE -25°C to +85°C 16 Lead Wide SO
DG302ABK -25°C to +85°C 14 Lead CERDIP
DG303C/D 0°C to +70°C Dice
DG303CJ 0°C to +70°C 14 Lead Plastic DIP
DG303CWE 0°C to +70°C 16 Lead Wide SO
DG303CK 0°C to +70°C 14 Lead CERDIP
DG303BWE -25°C to +85°C 16 Lead Wide SO
DG303BK -25°C to +85°C 14 Lead CERDIP
DG303AK -55°C to +125°C 14 Lead CERDIP
DG303AC/D 0°C to +70°C Dice
DG303ACJ 0°C to +70°C 14 Lead Plastic DIP
DG303ACWE 0°C to +70°C 16 Lead Wide SO
DG303ACK 0°C to +70°C 14 Lead CERDIP
DG303ABWE -25°C to +85°C 16 Lead Wide SO
DG303ABK -25°C to +85°C 14 Lead CERDIP
DG300(A)/DG301(A)/DG302(A)/DG303(A)
TTL Compatible CMOS Analog Switches
8 _______________________________________________________________________________________
PDIPN.EPS
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
DG300(A)/DG301(A)/DG302(A)/DG303(A)
TTL Compatible CMOS Analog Switches
_______________________________________________________________________________________ 9
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
SOICW.EPS
PACKAGE OUTLINE, .300" SOIC
1
1
21-0042 B
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
TOP VIEW
FRONT VIEW
MAX
0.012
0.104
0.019
0.299
0.013
INCHES
0.291
0.009
E
C
DIM
0.014
0.004
B
A1
MIN
0.093A
0.23
7.40 7.60
0.32
MILLIMETERS
0.10
0.35
2.35
MIN
0.49
0.30
MAX
2.65
0.050
0.016L0.40 1.27
0.5120.496D
D
MINDIM
D
INCHES
MAX
12.60 13.00
MILLIMETERS
MIN MAX
20 AC
0.447 0.463 AB11.7511.35 18
0.398 0.413 AA10.5010.10 16
N MS013
SIDE VIEW
H 0.4190.394 10.00 10.65
e 0.050 1.27
D 0.6140.598 15.20 2415.60 AD
D 0.7130.697 17.70 2818.10 AE
H
E
N
D
A1
B
e
A
0∞-8∞
C
L
1
VARIATIONS:
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
CDIPS.EPS
DG300(A)/DG301(A)/DG302(A)/DG303(A)
TTL Compatible CMOS Analog Switches
10 ______________________________________________________________________________________
DG300(A)/DG301(A)/DG302(A)/DG303(A)
TTL Compatible CMOS Analog Switches
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 11
© 2007 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.
Revision History
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
0 2/88 Initial release —
1 6/99 Errors in the test limits and pin configuration —
2 9/04 Fixed Truth Table —
3 11/07 Correction to pin configuration 1