Aluminum electrolytic capacitors
Single-ended capacitors
Series/Type: B41858
Date: December 2010
© EPCOS AG 2010. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Long-life grade capacitors
for professional applications
Applications
For use in output circuits of switch-mode power supplies of
compact design
For professional industrial electronics, telecommunications
and data processing equipment
Automotive electronics
Features
Low impedance at high frequency
Low ESR
High ripple current capability
High reliability and long useful life
RoHS-compatible
Construction
Radial leads
Charge-discharge proof, polar
Aluminum case with insulating sleeve
Minus pole marking on the insulating sleeve
Case with safety vent
Delivery mode
Terminal configurations and packing:
Bulk
Taped, Ammo pack
Cut (see chapter "Single-ended Taping, packing and lead
configurations, Cut leads (Chapter B)")
Kinked (see chapter "Single-ended Taping, packing and
lead configurations, Kinked leads (Chapter B)")
PAPR (protection against polarity reversal):
crimped leads, J leads, bent leads
Refer to chapter "Single-ended capacitors Taping, packing
and lead configurations" for further details.
Single-ended capacitors B41858
Low impedance 105 °C
Page 2 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Specifications and characteristics in brief
Rated voltage VR
Surge voltage VS
10 ... 100 V DC
1.15 VR
Rated capacitance CR
Capacitance tolerance
22 ... 10000 µF
±20% M
Dissipation factor tan δ
(20 °C, 120 Hz)
For capacitance higher than 1000 µF add 0.02 for every increase of
1000 µF.
VR(V DC) 10 16 25 35 50 63 100
tan δ(max.) 0.19 0.16 0.14 0.12 0.10 0.10 0.08
Leakage current Ileak
(20 °C, 5 min)
Self-inductance ESL Diameter (mm) 8 ... 12.5 16 18
ESL (nH) 20 26 34
Useful life
105 °C; VR; IAC,R > 3000 h for d = 8 mm
> 5000 h for d ≥10 mm
Requirements ∆C/C ≤ ±40% of initial value
tan δ ≤ 3 times initial specified limit
Ileak ≤initial specified limit
Voltage endurance test
105 °C; VR3000 h for d = 8 mm
5000 h for d ≥10 mm
Post test requirements ∆C/C ≤ ±30% of initial value
tan δ ≤ 2 times initial specified limit
Ileak ≤initial specified limit
Vibration resistance test To IEC 60068-2-6, test Fc:
Frequency range 10 Hz ... 2 kHz, displacement amplitude max.
1.5 mm, acceleration max. 20 g, duration 3 ×2 h.
Capacitor rigidly clamped by the aluminum case.
IEC climatic category To IEC 60068-1:
55/105/56 (55 °C/+105 °C/56 days damp heat test)
Sectional specification IEC 60384-4, AEC Q200
B41858
Low impedance 105 °C
Page 3 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Dimensional drawings
With stand-off rubber seal
Diameters (mm): 10, 12.5, 16, 18
With flat rubber seal
Diameter (mm): 8
Dimensions and weights
Dimensions (mm) Approx. weight
d +0.5 l a ±0.5 b g
8 11.5 +1.5 3.5 0.60 ±0.05 1.0
10 12.5 +1.0 5.0 0.60 ±0.05 1.6
10 16 +1.0 5.0 0.60 ±0.05 1.9
10 20 +2.0 5.0 0.60 ±0.05 2.6
12.5 20 +2.0 5.0 0.60 ±0.05 3.6
12.5 25 +2.0 5.0 0.60 ±0.05 4.5
12.5 30 +2.0 5.0 0.80 ±0.05 5.3
12.5 40 +2.0 5.0 0.80 ±0.05 7.4
16 20 +2.0 7.5 0.80 ±0.05 5.5
16 25 +2.0 7.5 0.80 ±0.05 7.5
16 31.5 +2.0 7.5 0.80 ±0.05 7.8
16 35.5 +2.0 7.5 0.80 ±0.05 9.2
18 20 +2.0 7.5 0.80 ±0.1 8.0
18 25 +2.0 7.5 0.80 ±0.1 9.0
18 31.5 +2.0 7.5 0.80 ±0.1 11.0
18 35 +2.0 7.5 0.80 ±0.1 13.0
18 40 +2.0 7.5 0.80 ±0.1 16.0
B41858
Low impedance 105 °C
Page 4 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Overview of available types
VR(V DC) 10 16 25 35
Case dimensions d ×l (mm)
CR(µF)
100 8 ×11.5
120 8 ×11.5
150 8 ×11.5
180 8 ×11.5 10 ×12.5
220 8 ×11.5 10 ×12.5
270 8 ×11.5 10 ×12.5
330 8 ×11.5 8 ×11.5 10 ×12.5 10 ×16
390 8 ×11.5
470 8 ×11.5 10 ×12.5 10 ×16 10 ×20
560 10 ×12.5 10 ×16 10 ×16 10 ×20
680 10 ×12.5 10 ×16 10 ×20 12.5 ×20
820 10 ×16 10 ×20 10 ×20
1000 10 ×16 10 ×20 12.5 ×20 12.5 ×25
16 ×20
1200 10 ×16 10 ×20 16 ×20
1500 10 ×20 12.5 ×20 12.5 ×25 12.5 ×40
16 ×25
1800 10 ×20 12.5 ×25 16 ×20 16 ×25
18 ×20
2200 12.5 ×20 12.5 ×25 12.5 ×40
16 ×25
18 ×20
18 ×25
2700 12.5 ×25 16 ×20 16 ×31.5
18 ×20
18 ×31.5
3300 12.5 ×25
16 ×20
12.5 ×40
16 ×25
18 ×25 16 ×35.5
18 ×31.5
3900 12.5 ×40
16 ×20
16 ×31.5
18 ×20
16 ×35.5
18 ×31.5
18 ×35
4700 18 ×20 18 ×25 18 ×31.5 18 ×40
5600 12.5 ×40 18 ×35
6800 16 ×31.5 18 ×31.5 18 ×40
8200 18 ×31.5 18 ×35
10000 18 ×35 18 ×40
B41858
Low impedance 105 °C
Page 5 of 38Please read Cautions and warnings and
Important notes at the end of this document.
VR(V DC) 50 63 100
Case dimensions d ×l (mm)
CR(µF)
22 8 ×11.5
33 10 ×16
47 10 ×20
68 8 ×11.5
100 8 ×11.5 10 ×12.5 12.5 ×20
120 10 ×12.5 10 ×16 12.5 ×25
150 10 ×12.5 10 ×16
180 10 ×16 10 ×20 12.5 ×30
16 ×20
220 10 ×16 10 ×20 16 ×25
270 12.5 ×20 12.5 ×40
18 ×20
330 10 ×20 12.5 ×20 16 ×31.5
18 ×25
390 12.5 ×25 18 ×31.5
470 12.5 ×20 12.5 ×25
16 ×20
18 ×35
560 12.5 ×25 18 ×35
680 12.5 ×30 12.5 ×40
16 ×25
18 ×20
18 ×40
820 12.5 ×40
16 ×20
16 ×31.5
18 ×25
1000 16 ×31.5
18 ×20
16 ×31.5
1200 18 ×20 18 ×31.5
1500 18 ×25 18 ×35
1800 16 ×35.5
18 ×31.5
18 ×40
2200 18 ×35
2700 18 ×40
Other voltage and capacitance ratings are available upon request.
B41858
Low impedance 105 °C
Page 6 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 mm to 18 ×40 mm, excluding 12.5 ×30/40 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 10 V DC
330 8 ×11.5 2.195 0.274 0.246 436 B41858C3337M***
390 8 ×11.5 2.195 0.274 0.246 436 B41858C3397M***
470 8 ×11.5 2.195 0.274 0.246 436 B41858C3477M***
560 10 ×12.5 1.035 0.129 0.113 746 B41858C3567M***
680 10 ×12.5 1.035 0.129 0.113 746 B41858C3687M***
820 10 ×16 0.946 0.118 0.105 846 B41858C3827M***
1000 10 ×16 0.946 0.118 0.105 846 B41858C3108M***
1200 10 ×16 0.944 0.118 0.105 846 B41858C3128M***
1500 10 ×20 0.584 0.073 0.062 1202 B41858C3158M***
1800 10 ×20 0.584 0.073 0.062 1202 B41858C3188M***
2200 12.5 ×20 0.496 0.062 0.060 1396 B41858C3228M***
2700 12.5 ×25 0.327 0.041 0.034 2028 B41858C3278M***
3300 12.5 ×25 0.327 0.041 0.034 2028 B41858C3338M***
3300 16 ×20 0.307 0.038 0.033 2146 B41858D3338M***
3900 12.5 ×40 0.240 0.030 0.025 2858 B41858C3398M***
3900 16 ×20 0.307 0.038 0.033 2146 B41858D3398M***
4700 18 ×20 0.271 0.034 0.031 2381 B41858C3478M***
5600 12.5 ×40 0.243 0.030 0.025 2858 B41858C3568M***
6800 16 ×31.5 0.192 0.024 0.022 3122 B41858C3688M***
8200 18 ×31.5 0.165 0.021 0.020 3539 B41858C3828M***
10000 18 ×35 0.160 0.020 0.018 3864 B41858C3109M***
B41858
Low impedance 105 °C
Page 7 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 mm to 18 ×40 mm, excluding 12.5 ×30/40 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 16 V DC
270 8 ×11.5 2.192 0.274 0.246 436 B41858D4277M***
330 8 ×11.5 2.192 0.274 0.246 436 B41858D4337M***
470 10 ×12.5 1.035 0.129 0.113 746 B41858C4477M***
560 10 ×16 0.944 0.118 0.105 846 B41858C4567M***
680 10 ×16 0.946 0.118 0.105 846 B41858C4687M***
820 10 ×20 0.584 0.073 0.062 1202 B41858C4827M***
1000 10 ×20 0.584 0.073 0.062 1202 B41858C4108M***
1200 10 ×20 0.584 0.073 0.062 1202 B41858C4128M***
1500 12.5 ×20 0.496 0.062 0.060 1396 B41858C4158M***
1800 12.5 ×25 0.327 0.041 0.034 2028 B41858C4188M***
2200 12.5 ×25 0.327 0.041 0.034 2028 B41858C4228M***
2700 16 ×20 0.307 0.038 0.033 2146 B41858C4278M***
3300 12.5 ×40 0.243 0.030 0.025 2858 B41858D4338M***
3300 16 ×25 0.251 0.031 0.029 2483 B41858C4338M***
3900 16 ×31.5 0.192 0.024 0.022 3122 B41858D4398M***
3900 18 ×20 0.271 0.034 0.031 2381 B41858C4398M***
4700 18 ×25 0.217 0.027 0.024 2941 B41858C4478M***
6800 18 ×31.5 0.165 0.021 0.020 3539 B41858C4688M***
8200 18 ×35 0.160 0.020 0.018 3864 B41858C4828M***
10000 18 ×40 0.125 0.016 0.015 4467 B41858C4109M***
B41858
Low impedance 105 °C
Page 8 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 mm to 18 ×40 mm, excluding 12.5 ×30/40 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 25 V DC
180 8 ×11.5 2.192 0.274 0.246 436 B41858D5187M***
220 8 ×11.5 2.192 0.274 0.246 436 B41858D5227M***
270 10 ×12.5 1.032 0.129 0.113 746 B41858C5277M***
330 10 ×12.5 1.035 0.129 0.113 746 B41858C5337M***
470 10 ×16 0.946 0.118 0.105 846 B41858C5477M***
560 10 ×16 0.944 0.118 0.105 846 B41858C5567M***
680 10 ×20 0.584 0.073 0.062 1202 B41858C5687M***
820 10 ×20 0.584 0.073 0.062 1202 B41858C5827M***
1000 12.5 ×20 0.496 0.062 0.060 1396 B41858C5108M***
1500 12.5 ×25 0.327 0.041 0.034 2028 B41858C5158M***
1800 16 ×20 0.307 0.038 0.033 2146 B41858C5188M***
2200 12.5 ×40 0.243 0.030 0.025 2858 B41858D5228M***
2200 16 ×25 0.251 0.031 0.029 2483 B41858C5228M***
2200 18 ×20 0.248 0.031 0.031 2381 B41858E5228M***
2700 16 ×31.5 0.192 0.024 0.022 3122 B41858D5278M***
2700 18 ×20 0.271 0.034 0.031 2381 B41858C5278M***
3300 18 ×25 0.217 0.027 0.024 2941 B41858C5338M***
3900 16 ×35.5 0.168 0.021 0.019 3408 B41858D5398M***
3900 18 ×31.5 0.165 0.021 0.020 3539 B41858C5398M***
4700 18 ×31.5 0.168 0.021 0.020 3539 B41858D5478M***
5600 18 ×35 0.160 0.020 0.018 3864 B41858D5568M***
6800 18 ×40 0.128 0.016 0.015 4467 B41858C5688M***
B41858
Low impedance 105 °C
Page 9 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 mm to 18 ×40 mm, excluding 12.5 ×30/40 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 35 V DC
100 8 ×11.5 2.192 0.274 0.246 436 B41858C7107M***
120 8 ×11.5 2.192 0.274 0.246 436 B41858D7127M***
150 8 ×11.5 2.192 0.274 0.246 436 B41858C7157M***
180 10 ×12.5 1.035 0.129 0.113 746 B41858C7187M***
220 10 ×12.5 1.035 0.129 0.113 746 B41858C7227M***
330 10 ×16 0.946 0.118 0.105 846 B41858C7337M***
470 10 ×20 0.584 0.073 0.062 1202 B41858C7477M***
560 10 ×20 0.584 0.073 0.062 1202 B41858C7567M***
680 12.5 ×20 0.496 0.062 0.060 1396 B41858C7687M***
1000 12.5 ×25 0.327 0.041 0.034 2028 B41858C7108M***
1000 16 ×20 0.304 0.038 0.033 2146 B41858D7108M***
1200 16 ×20 0.307 0.038 0.033 2146 B41858C7128M***
1500 12.5 ×40 0.243 0.030 0.025 2858 B41858D7158M***
1500 16 ×25 0.251 0.031 0.029 2483 B41858C7158M***
1800 16 ×25 0.248 0.031 0.029 2483 B41858E7188M***
1800 18 ×20 0.271 0.034 0.031 2381 B41858C7188M***
2200 18 ×25 0.217 0.027 0.024 2941 B41858C7228M***
2700 18 ×31.5 0.165 0.021 0.020 3539 B41858C7278M***
3300 16 ×35.5 0.168 0.021 0.019 3408 B41858E7338M***
3300 18 ×31.5 0.168 0.021 0.020 3539 B41858D7338M***
3900 18 ×35 0.160 0.020 0.018 3864 B41858C7398M***
4700 18 ×40 0.125 0.016 0.015 4467 B41858C7478M***
B41858
Low impedance 105 °C
Page 10 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 mm to 18 ×40 mm, excluding 12.5 ×30/40 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 50 V DC
100 8 ×11.5 5.168 0.646 0.573 340 B41858C6107M***
120 10 ×12.5 2.984 0.373 0.336 555 B41858C6127M***
150 10 ×12.5 2.984 0.373 0.336 555 B41858C6157M***
180 10 ×16 1.400 0.175 0.160 778 B41858C6187M***
220 10 ×16 1.400 0.175 0.160 778 B41858C6227M***
330 10 ×20 1.000 0.125 0.118 1030 B41858C6337M***
470 12.5 ×20 0.880 0.110 0.104 1300 B41858C6477M***
560 12.5 ×25 0.712 0.089 0.082 1490 B41858C6567M***
680 12.5 ×30 0.360 0.045 0.043 2140 B41858C6687M***
820 12.5 ×40 0.269 0.034 0.032 2799 B41858C6827M***
820 16 ×20 0.401 0.050 0.046 1820 B41858D6827M***
1000 16 ×31.5 0.260 0.032 0.030 2653 B41858C6108M***
1000 18 ×20 0.477 0.048 0.044 1997 B41858D6108M***
1200 18 ×20 0.384 0.048 0.044 1997 B41858C6128M***
1500 18 ×25 0.382 0.038 0.036 2417 B41858C6158M***
1800 16 ×35.5 0.232 0.029 0.026 2896 B41858D6188M***
1800 18 ×31.5 0.300 0.030 0.028 2989 B41858C6188M***
2200 18 ×35 0.268 0.027 0.024 3320 B41858C6228M***
2700 18 ×40 0.210 0.021 0.020 3871 B41858C6278M***
B41858
Low impedance 105 °C
Page 11 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 mm to 18 ×40 mm, excluding 12.5 ×30/40 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 63 V DC
68 8 ×11.5 4.328 0.541 0.488 310 B41858C8686M***
100 10 ×12.5 4.616 0.577 0.500 354 B41858C8107M***
120 10 ×16 3.075 0.308 0.279 519 B41858C8127M***
150 10 ×16 2.464 0.308 0.279 519 B41858C8157M***
180 10 ×20 1.986 0.199 0.180 705 B41858C8187M***
220 10 ×20 1.592 0.199 0.180 705 B41858C8227M***
270 12.5 ×20 1.688 0.169 0.153 876 B41858C8277M***
330 12.5 ×20 1.688 0.169 0.153 876 B41858C8337M***
390 12.5 ×25 1.236 0.124 0.112 1118 B41858C8397M***
470 12.5 ×25 0.992 0.124 0.112 1118 B41858E8477M***
470 16 ×20 1.037 0.104 0.094 1272 B41858C8477M***
680 12.5 ×40 0.717 0.072 0.065 1785 B41858C8687M***
680 16 ×25 0.772 0.077 0.070 1600 B41858D8687M***
680 18 ×20 0.960 0.096 0.087 1427 B41858E8687M***
820 16 ×31.5 0.541 0.054 0.049 2092 B41858C8827M***
820 18 ×25 0.761 0.076 0.069 1735 B41858D8827M***
1000 16 ×31.5 0.432 0.054 0.049 2092 B41858C8108M***
1200 18 ×31.5 0.518 0.052 0.047 2294 B41858C8128M***
1500 18 ×35 0.441 0.044 0.040 2592 B41858C8158M***
1800 18 ×40 0.375 0.038 0.034 2967 B41858C8188M***
B41858
Low impedance 105 °C
Page 12 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
ESRmax
10 kHz
40 °C
Ω
ESRmax
10 kHz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
105 °C
mA
Ordering code
(composition see
below)
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for d ×l=10×20 mm to 18 ×40 mm, excluding 12.5 ×30/40 mm)
002 = for cut leads, bulk (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 mm)
003 = for crimped leads, blister (for ∅16 ... 18 mm)
004 = for J leads, blister (for ∅10 ... 18 mm, excluding d ×l = 12.5 ×30/40 and 18 ×40 mm)
006 = for taped leads, Ammo pack, lead spacing F = 3.5 mm (for ∅8 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (for d ×l=8×11.5 ... 12.5 ×25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (for d ×l=16×20 ... 16 ×31.5 mm and
18 ×20 ... 18 ×31.5 mm)
012 = for bent 90°leads, blister (for ∅16 ... 18 mm)
VR= 100 V DC
22 8 ×11.5 12.219 1.222 1.114 205 B41858C9226M***
33 10 ×16 6.542 0.654 0.589 357 B41858C9336M***
47 10 ×20 3.688 0.461 0.423 460 B41858C9476M***
100 12.5 ×20 3.048 0.305 0.281 647 B41858C9107M***
120 12.5 ×25 2.038 0.204 0.188 864 B41858C9127M***
180 12.5 ×30 1.732 0.173 0.159 1009 B41858C9187M***
180 16 ×20 1.313 0.131 0.122 1119 B41858D9187M***
220 16 ×25 0.985 0.099 0.091 1402 B41858C9227M***
270 12.5 ×40 1.314 0.131 0.121 1309 B41858C9277M***
270 18 ×20 1.260 0.126 0.119 1220 B41858D9277M***
330 16 ×31.5 0.973 0.097 0.090 1546 B41858C9337M***
330 18 ×25 1.008 0.101 0.095 1477 B41858D9337M***
390 18 ×31.5 0.720 0.072 0.068 1907 B41858C9397M***
470 18 ×35 0.679 0.068 0.063 2061 B41858C9477M***
560 18 ×35 0.679 0.068 0.063 2061 B41858C9567M***
680 18 ×40 0.438 0.044 0.042 2683 B41858C9687M***
B41858
Low impedance 105 °C
Page 13 of 38Please read Cautions and warnings and
Important notes at the end of this document.
1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life
graphs.
Useful life
depending on ambient temperature TAunder ripple current operating conditions1)
d=8mm
Useful life
depending on ambient temperature TAunder ripple current operating conditions1)
d≥10 mm
B41858
Low impedance 105 °C
Page 14 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Frequency factor of permissible ripple current IAC versus frequency f
B41858
Low impedance 105 °C
Page 15 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Taping, packing and lead configurations
Taping
Single-ended capacitors are available taped in Ammo pack from diameter 4 to 18 mm as follows:
Lead spacing F = 2.0 mm (∅d=4 … 5 mm)
Lead spacing F = 2.5 mm (∅d=4 … 6.3 mm)
Lead spacing F = 3.5 mm (∅d = 8 mm)
Lead spacing F = 5.0 mm (∅d=4 … 12.5 mm)
Lead spacing F = 7.5 mm (∅d = 16 ... 18 mm).
Lead spacing 2.0 mm (∅d = 4 ... 5 mm)
Last 3 digits of ordering code: 016
Dimensions in mm
∅d F H W W0W1W2P P0P1I1t∆h D0
4 ... 5 2.0 18.5 18.0 7.0 9.0 3.0 12.7 12.7 5.10 1.0 0.7 1 4.0
+0.8
0.2 ±0.75 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.7 max. ±0.2 ±1.0 ±0.2
B41858
Low impedance 105 °C
Page 16 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 2.5 mm (∅d = 4 ... 6.3 mm)
Last 3 digits of ordering code: 007
Dimensions in mm
∅d F H W W0W1W2H0P P0P1I1t∆h D0
4 ... 6.3 2.5 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 5.1 1.0 0.7 1.0 4.0
Toler-
rance
+0.8
0.2 ±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2
Lead spacing 3.5 mm (∅d = 8 mm)
Last 3 digits of ordering code: 006
Dimensions in mm
∅d F H W W0W1W2P P0P1I1t∆h D0
8 3.5 18.5 18.0 10 9.0 3.0 12.7 12.7 4.6 1.0 0.7 1.0 4.0
Toler-
ance
+0.8
0.2 ±1.0 ±0.5 min. ±0.5 max. ±1.0 ±0.3 ±0.6 max. ±0.2 max. ±0.2
Leads can also run straight through the taping area. Taping is available up to dimensions
d×l=8×15 mm.
B41858
Low impedance 105 °C
Page 17 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 5.0 mm (∅d = 4 ... 8 mm)
Last 3 digits of ordering code: 008
Lead spacing 5.0 mm (∅d = 10 ... 12.5 mm)
Last 3 digits of ordering code: 008
Dimensions in mm
∅d F H W W0W1W2H0P P0P1I1t∆h D0
4 ...
6.3 5.0 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 3.85 1.0 0.6 1.0 4.0
820.0 10.0 16.0 12.7 12.7 3.85
10 5.0 19.0 18.0 12.5 9.0 1.5 12.7 12.7 3.85 1.0 0.6 1.0 4.0
12.5 19.0 12.5 15.0 15.0 5.0
Toler-
ance
+0.8
0.2 ±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. +0.3
0.2 max. ±0.2
Taping is available up to dimensions d ×l=10×31.5 mm and 12.5 ×25 mm.
Taping is not available for d ×l=8×20 mm.
B41858
Low impedance 105 °C
Page 18 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Lead spacing 7.5 mm (∅d = 16 ...18 mm)
Last 3 digits of ordering code: 009
Dimensions in mm
∅d F H W W0W1W2P P0P1I1t∆P∆h D0
16 7.5 18.5 18.0 12.5 9.0 1.5 30.0 15.0 3.75 1.0 0.7 0 0 4.0
18
Toler-
ance ±0.8 0.5
+0.75 ±0.5 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 ±1.0 ±1.0 ±0.2
Taping is available up to dimensions d ×l=16×31.5 mm and 18 ×31.5 mm.
B41858
Low impedance 105 °C
Page 19 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Cut or kinked leads
Single-ended capacitors are available with cut or kinked leads. Other lead configurations also
available upon request.
Cut leads (Chapter A)
Available for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086,
B43088, B43827, B43828.
Last 3 digits of ordering code: 002
Case size d x l (mm) Dimensions
(mm)
a±0.5
4 x 7 1.5
5 x 7 2.0
5 x 11 2.0
6.3 x 7 2.5
6.3 x 11 2.5
8 x 7 3.5
8 x 11.5 3.5
8 x 15 3.5
8 x 20 3.5
10 x 12.5 5.0
10 x 16 5.0
10 x 20 5.0
10 x 25 5.0
10 x 31.5 5.0
Case size d x l (mm) Dimensions
(mm)
a±0.5
12.5 x 16 5.0
12.5 x 20 5.0
12.5 x 25 5.0
12.5 x 31.5 5.0
12.5 x 35.5 5.0
12.5 x 40 5.0
16 x 20 7.5
16 x 25 7.5
16 x 31.5 7.5
16 x 35.5 7.5
16 x 40 7.5
18 x 20 7.5
18 x 25 7.5
18 x 31.5 7.5
18 x 35.5 7.5
18 x 40 7.5
B41858
Low impedance 105 °C
Page 20 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Cut leads (Chapter B)
Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896,
B42824, B42851, B43866, B43867, B43890, B43896.
Last 3 digits of ordering code: 002
With stand-off rubber seal Case size Dimensions (mm)
d×l (mm) a ±0.5
10 ×12.5 5.0
10 ×16 5.0
10 ×20 5.0
12.5 ×20 5.0
12.5 ×25 5.0
16 ×20 7.5
16 ×25 7.5
16 ×31.5 7.5
16 ×35.5 7.5
18 ×20 7.5
18 ×25 7.5
18 ×31.5 7.5
18 ×35 7.5
18 ×40 7.5
With flat rubber seal
B41858
Low impedance 105 °C
Page 21 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Kinked leads (Chapter A)
Available for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086,
B43088, B43827, B43828.
Last 3 digits of ordering code: 001
Case size d x l (mm) Dimensions
(mm)
a±0.5
4 x 7 1.5
5 x 7 2.0
5 x 11 2.0
6.3 x 7 2.5
6.3 x 11 2.5
8 x 7 3.5
8 x 11.5 3.5
8 x 15 3.5
8 x 20 3.5
10 x 12.5 5.0
10 x 16 5.0
10 x 20 5.0
10 x 25 5.0
10 x 31.5 5.0
Case size d x l (mm) Dimensions
(mm)
a±0.5
12.5 x 16 5.0
12.5 x 20 5.0
12.5 x 25 5.0
12.5 x 31.5 5.0
12.5 x 35.5 5.0
12.5 x 40 5.0
16 x 20 7.5
16 x 25 7.5
16 x 31.5 7.5
16 x 35.5 7.5
16 x 40 7.5
18 x 20 7.5
18 x 25 7.5
18 x 31.5 7.5
18 x 35.5 7.5
18 x 40 7.5
B41858
Low impedance 105 °C
Page 22 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Kinked leads (Chapter B)
Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896,
B42824, B42851, B43866, B43867, B43890, B43896.
Last 3 digits of ordering code: 001
With stand-off rubber seal Case size Dimensions (mm)
d×l (mm) a ±0.5
10 ×20 5.0
12.5 ×20 5.0
12.5 ×25 5.0
16 ×20 7.5
16 ×25 7.5
16 ×31.5 7.5
16 ×35.5 7.5
18 ×20 7.5
18 ×25 7.5
18 ×31.5 7.5
18 ×35 7.5
18 ×40 7.5
With flat rubber seal
B41858
Low impedance 105 °C
Page 23 of 38Please read Cautions and warnings and
Important notes at the end of this document.
PAPR leads (Protection Against Polarity Reversal)
These lead configurations ensure correct placement of the capacitor on the PCB with regard to
polarity. PAPR leads are available for diameters from 10 mm up to 18 mm.
There are three configurations available: Crimped leads, J leads, bent 90°leads
Available for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896,
B42824, B42851, B43866, B43867, B43890, B43896.
Crimped leads
Last 3 digits of ordering code: 003
With stand-off rubber seal With flat rubber seal
Suggestion for PCB hole diameter
Case size Dimensions (mm)
d×l (mm) B ±0.2 C ±0.5 D ±0.1 E ±0.1 a ±0.5 ∅b
16 ×20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
16 ×25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
16 ×31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
16 ×35.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05
18 ×20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×35 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
18 ×40 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1
B41858
Low impedance 105 °C
Page 24 of 38Please read Cautions and warnings and
Important notes at the end of this document.
J leads
Last 3 digits of ordering code: 004
Suggestion for PCB hole diameter
Case size Dimensions (mm)
d×l (mm) C ±0.5 E ±0.5 J ±0.2 a ±0.5 ∅b
10 ×12.5 3.2 0.7 1.2 5.0 0.6 ±0.05
10 ×16 3.2 0.7 1.2 5.0 0.6 ±0.05
10 ×20 3.2 0.7 1.2 5.0 0.6 ±0.05
12.5 ×20 3.2 0.7 1.2 5.0 0.6 ±0.05
12.5 ×25 3.2 0.7 1.2 5.0 0.6 ±0.05
16 ×20 3.5 0.7 1.6 7.5 0.8 ±0.05
16 ×25 3.5 0.7 1.6 7.5 0.8 ±0.05
16 ×31.5 3.5 0.7 1.6 7.5 0.8 ±0.05
16 ×35.5 3.5 0.7 1.6 7.5 0.8 ±0.05
18 ×20 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×25 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×31.5 3.5 0.7 1.6 7.5 0.8 ±0.1
18 ×35 3.5 0.7 1.6 7.5 0.8 ±0.1
B41858
Low impedance 105 °C
Page 25 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Bent 90°leads for horizontal mounting pinning
Last 3 digits of ordering code: 012
Case size Dimensions (mm)
d×l (mm) C ±0.5 E ±0.5 F ±0.5 a ±0.5 ∅b
16 ×20 4.0 4.0 12.0 7.5 0.8 ±0.05
16 ×25 4.0 4.0 12.0 7.5 0.8 ±0.05
16 ×31.5 4.0 4.0 12.0 7.5 0.8 ±0.05
16 ×35.5 4.0 4.0 12.0 7.5 0.8 ±0.05
18 ×20 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×25 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×31.5 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×35 4.0 4.0 13.0 7.5 0.8 ±0.1
18 ×40 4.0 4.0 13.0 7.5 0.8 ±0.1
Bent leads for diameter 12.5 mm available upon request.
B41858
Low impedance 105 °C
Page 26 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Packing units and box dimensions
Ammo pack
Valid for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088,
B43827, B43828.
Case size
d×l
Dimensions (mm) Packing
units
mm Amax Bmax Cmax pcs.
4×7 330 50 196 2000
5×7 330 50 226 2000
5×11 330 50 226 2000
6.3 ×7 330 50 286 2000
6.3 ×11 330 50 286 2000
8×7 330 50 246 1000
8×11.5 330 50 246 1000
8×15 330 50 246 500
10 ×12.5 330 50 196 500
10 ×16 330 54 196 500
10 ×20 330 58 196 500
12.5 ×20 341 60 272 500
12.5 ×25 341 65 272 500
16 ×25 320 65 270 300
16 ×31.5 315 65 275 300
18 ×20 315 65 275 250
18 ×25 315 65 275 250
18 ×31.5 315 65 275 250
B41858
Low impedance 105 °C
Page 27 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Ammo pack
Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824,
B42851, B43866, B43867, B43890, B43896.
Case size
d×l
Dimensions (mm) Packing
units
mm Amax Bmax Cmax pcs.
8×11.5 345 55 240 1000
10 ×12.5 345 55 280 750
10 ×16 345 60 200 500
10 ×20 345 60 200 500
12.5 ×20 345 65 280 500
12.5 ×25 345 65 280 500
16 ×20 315 65 275 300
16 ×25 315 65 275 300
16 ×31.5 315 65 275 300
18 ×20 315 65 275 250
18 ×25 315 65 275 250
18 ×31.5 315 65 275 250
B41858
Low impedance 105 °C
Page 28 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Overview of packing units and code numbers for case sizes 4 x 7 ... 16 x 40
Valid for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088,
B43827, B43828.
Case size
dxl
mm
Standard,
bulk
pcs.
Taped,
Ammo pack
pcs.
Kinked leads,
bulk
pcs.
Cut leads,
bulk
pcs.
4 x 7 10000 2000 15000 15000
5 x 7 7500 2000 10000 10000
5 x 11 5000 2000 10000 10000
6.3 x 7 5000 2000 10000 10000
6.3 x 11 5000 2000 5000 5000
8 x 7 5000 1000 5000 5000
8 x 11.5 2500 1000 4000 4000
8 x 15 2000 1000 2500 2500
8 x 20 1500 2000 2000
10 x 12.5 2000 500 2500 2500
10 x 16 1500 500 2000 2000
10 x 20 1000 500 1500 1500
10 x 25 1000 500 1250 1250
12.5 x 16 750 500 1000 1000
12.5 x 20 750 500 500 500
12.5 x 25 750 500 500 500
12.5 x 31.5 500 750 750
12.5 x 35.5 500 750 750
12.5 x 40 500 750 750
16 x 20 375 300 500 500
16 x 25 375 300 500 500
16 x 31.5 250 300 375 375
16 x 35.5 250 375 375
16 x 40 250 375 375
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002
006
007
008
009
016
3.5
2.5
5.0
7.5
2.0
8
4 ... 6.3
4 ... 12.5
16 ... 18
4 ... 5
B41858
Low impedance 105 °C
Page 29 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Overview of packing units and code numbers for case sizes 18 x 20 ... 18 x 40
Valid for series B41002, B41022, B41044, B41827, B41828, B43044, B43082, B43086, B43088,
B43827, B43828.
Case size
dxl
mm
Standard,
bulk
pcs.
Taped,
Ammo pack
pcs.
Kinked leads,
bulk
pcs.
Cut leads,
bulk
pcs.
18 x 20 250 250 100 100
18 x 25 250 250 100 100
18 x 31.5 250 250 100 100
18 x 35.5 250 100 100
18 x 40 250 100 100
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002
009 7.5 16 ... 18
B41858
Low impedance 105 °C
Page 30 of 38Please read Cautions and warnings and
Important notes at the end of this document.
1) Available upon request
Overview of packing units and code numbers for case sizes 8 ×11.5 ... 16 ×35.5
Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824,
B42851, B43866, B43867, B43890, B43896.
PAPR
Case size
d×l
Stan-
dard,
bulk
Taped,
Ammo pack
Kinked
leads,
bulk
Cut
leads,
bulk
Crimped
leads,
blister
J leads,
blister
Bent 90°
leads,
blister
mm pcs. pcs. pcs. pcs. pcs. pcs. pcs.
8×11.5 1000 1000
10 ×12.5 1000 750 1000 675
10 ×16 1000 500 1000 675
10 ×20 500 500 500 500 500
12.5 ×20 350 500 350 350 300 1)
12.5 ×25 250 500 500 500 225 1)
12.5 ×30 200
12.5 ×35 175
12.5 ×40 175
16 ×20 250 300 200 200 200 200 120
16 ×25 250 300 200 200 200 200 120
16 ×31.5 200 300 250 250 344 344 120
16 ×35.5 100 100 100 150 150 150
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002 003 004 012
006
008
009
3.5
5
7.5
8
5...12.5
16...18
B41858
Low impedance 105 °C
Page 31 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Overview of packing units and code numbers for case sizes 18 ×20 ... 18 ×40
Valid for series B41858, B41859, B41863, B41866, B41868, B41888, B41890, B41896, B42824,
B42851, B43866, B43867, B43890, B43896.
PAPR
Case size
d×l
Stan-
dard,
bulk
Taped,
Ammo pack
Kinked
leads,
bulk
Cut
leads,
bulk
Crimped
leads,
blister
J leads,
blister
Bent 90°
leads,
blister
mm pcs. pcs. pcs. pcs. pcs. pcs. pcs.
18 ×20 175 250 175 175 200 200 120
18 ×25 150 250 150 150 200 200 120
18 ×31.5 100 250 100 100 150 150 120
18 ×35 100 100 100 150 150 150
18 ×40 125 100 100 120 72
The last three
digits of the
complete
ordering code
state the lead
configuration
000 Code F (mm) d (mm) 001 002 003 004 012
009 7.5 16...18
B41858
Low impedance 105 °C
Page 32 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended
application, but also with regard to health and environmental compatibility. They do not contain
any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They
contain flame-retarding substances which will quickly extinguish any flame that may have been
ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no safe substitute materials are
currently known. However, the amount of dangerous materials used in our products has been
limited to an absolute minimum. Nevertheless, the following rules should be observed when
handling aluminum electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin.
If electrolyte does come into contact with the skin, wash the affected parts immediately with
running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If
symptoms persist, seek medical treatment.
Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be
well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
B41858
Low impedance 105 °C
Page 33 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Product safety
The table below summarizes the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic Safety information Reference
chapter "General
technical information"
Polarity Make sure that polar capacitors are connected
with the right polarity.
1
"Basic construction of
aluminum electrolytic
capacitors"
Reverse voltage Voltages polarity classes should be prevented by
connecting a diode.
3.1.6
"Reverse voltage"
Upper category
temperature
Do not exceed the upper category temperature. 7.2
"Maximum permissible
operating temperature"
Maintenance Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
10
"Maintenance"
Mounting
position of screw-
terminal capacitors
Do not mount the capacitor with the terminals
(safety vent) upside down.
11.1.
"Mounting positions of
capacitors with screw
terminals"
Mounting of
single-ended
capacitors
The internal structure of single-ended capacitors
might be damaged if excessive force is applied to
the lead wires.
Avoid any compressive, tensile or flexural stress.
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
11.4
"Mounting
considerations for
single-ended capacitors"
Robustness of
terminals
The following maximum tightening torques must
not be exceeded when connecting screw
terminals:
M5: 2 Nm
M6: 2.5 Nm
11.3
"Mounting torques"
Soldering Do not exceed the specified time or temperature
limits during soldering.
11.5
"Soldering"
B41858
Low impedance 105 °C
Page 34 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Topic Safety information Reference
chapter "General
technical information"
Soldering,
cleaning agents
Do not allow halogenated hydrocarbons to come
into contact with aluminum electrolytic capacitors.
11.6
"Cleaning agents"
Passive
flammability
Avoid external energy, such as fire or electricity. 8.1
"Passive flammability"
Active
flammability
Avoid overload of the capacitors. 8.2
"Active flammability"
Reference
chapter "Capacitors with
screw terminals"
Breakdown strength
of insulating
sleeves
Do not damage the insulating sleeve, especially
when ring clips are used for mounting.
"Screw terminals
accessories"
B41858
Low impedance 105 °C
Page 35 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Symbols and terms
Symbol English German
C Capacitance Kapazität
CRRated capacitance Nennkapazität
CSSeries capacitance Serienkapazität
CS,T Series capacitance at temperature T Serienkapazität bei Temperatur T
CfCapacitance at frequency f Kapazität bei Frequenz f
d Case diameter, nominal dimension Gehäusedurchmesser, Nennmaß
dmax Maximum case diameter Maximaler Gehäusedurchmesser
ESL Self-inductance Eigeninduktivität
ESR Equivalent series resistance Ersatzserienwiderstand
ESRfEquivalent series resistance at
frequency f
Ersatzserienwiderstand bei Frequenz f
ESRTEquivalent series resistance at
temperature T
Ersatzserienwiderstand bei Temperatur T
f Frequency Frequenz
I Current Strom
IAC Alternating current (ripple current) Wechselstrom
IAC,rms Root-mean-square value of alternating
current
Wechselstrom, Effektivwert
IAC,f Ripple current at frequency f Wechselstrom bei Frequenz f
IAC,max Maximum permissible ripple current Maximal zulässiger Wechselstrom
IAC,R Rated ripple current Nennwechselstrom
IAC,R (B) Rated ripple current for base cooling Nennwechselstromstrom für Bodenkühlung
Ileak Leakage current Reststrom
Ileak,op Operating leakage current Betriebsreststrom
l Case length, nominal dimension Gehäuselänge, Nennmaß
lmax Maximum case length (without
terminals and mounting stud)
Maximale Gehäuselänge (ohne Anschlüsse
und Gewindebolzen)
R Resistance Widerstand
Rins Insulation resistance Isolationswiderstand
Rsymm Balancing resistance Symmetrierwiderstand
T Temperature Temperatur
∆T Temperature difference Temperaturdifferenz
TAAmbient temperature Umgebungstemperatur
TCCase temperature Gehäusetemperatur
TBCapacitor base temperature Temperatur des Becherbodens
t Time Zeit
∆t Period Zeitraum
tbService life (operating hours) Brauchbarkeitsdauer (Betriebszeit)
B41858
Low impedance 105 °C
Page 36 of 38Please read Cautions and warnings and
Important notes at the end of this document.
Symbol English German
V Voltage Spannung
VFForming voltage Formierspannung
Vop Operating voltage Betriebsspannung
VRRated voltage, DC voltage Nennspannung, Gleichspannung
VSSurge voltage Spitzenspannung
XCCapacitive reactance Kapazitiver Blindwiderstand
XLInductive reactance Induktiver Blindwiderstand
Z Impedance Scheinwiderstand
ZTImpedance at temperature T Scheinwiderstand bei Temperatur T
tan δDissipation factor Verlustfaktor
λFailure rate Ausfallrate
ε0Absolute permittivity Elektrische Feldkonstante
εrRelative permittivity Dielektrizitätszahl
ωAngular velocity; 2 πf Kreisfrequenz; 2 πf
Note
All dimensions are given in mm.
B41858
Low impedance 105 °C
Page 37 of 38Please read Cautions and warnings and
Important notes at the end of this document.
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical re-
quirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incum-
bent on the customer to check and decide whether an EPCOS product with the properties de-
scribed in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in
which the malfunction or failure of an electronic component could endanger human life or
health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by
means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our Ma-
terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-
tailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in the case of individual agreements deviating from the fore-
going for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-
sion of the "General Terms of Delivery for Products and Services in the Electrical In-
dustry" published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap,
DigiSiMic, DSSP, FormFit, MiniBlue, MiniCell, MKK, MKD, MLSC, MotorCap, PCC,
PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trade-
marks registered or pending in Europe and in other countries. Further information will be
found on the Internet at www.epcos.com/trademarks.
Important notes
Page 38 of 38
