8-/10-/12-/14-Bit High Bandwidth Multiplying DACs with Serial Interface AD5450/AD5451/AD5452/AD5453 Data Sheet FEATURES FUNCTIONAL BLOCK DIAGRAM APPLICATIONS VDD AD5450/ AD5451/ AD5452/ AD5453 VREF R 8-/10-/12-/14-BIT REF R-2R DAC RFB IOUT1 DAC REGISTER POWER-ON RESET INPUT LATCH SYNC SCLK SDIN CONTROL LOGIC AND INPUT SHIFT REGISTER 04587-001 12 MHz multiplying bandwidth Integral nonlinearity (INL) of 0.25 LSB at 8-bit 8-lead TSOT and MSOP packages 2.5 V to 5.5 V supply operation Pin-compatible 8-/10-/12-/14-bit current output DACs 10 V reference input 50 MHz serial interface 2.7 MSPS update rate Extended temperature range: -40C to +125C 4-quadrant multiplication Power-on reset with brownout detect <0.4 A typical current consumption Guaranteed monotonic Qualified for automotive applications GND Figure 1. Portable battery-powered applications Waveform generators Analog processing Instrumentation applications Programmable amplifiers and attenuators Digitally controlled calibration Programmable filters and oscillators Composite video Ultrasound Gain, offset, and voltage trimming Qualified for automotive applications GENERAL DESCRIPTION The AD5450/AD5451/AD5452/AD54531 are CMOS 8-/10-/12-/ 14-bit current output digital-to-analog converters (DACs), respecttively. These devices operate from a 2.5 V to 5.5 V power supply, making them suited to several applications including batterypowered applications. As a result of manufacture on a CMOS submicron process, these DACs offer excellent 4-quadrant multiplication characteristics of up to 12 MHz. These DACs use a double-buffered, 3-wire serial interface that is compatible with SPI, QSPITM, MICROWIRETM, and most digital signal processor (DSP) interface standards. Upon power-up, the internal shift register and latches are filled with 0s, and the DAC output is at zero scale. 1 The applied external reference input voltage (VREF) determines the full-scale output current. These devices can handle 10 V inputs on the reference, despite operating from a single-supply power supply of 2.5 V to 5.5 V. An integrated feedback resistor (RFB) provides temperature tracking and full-scale voltage output when combined with an external current to voltage precision amplifier. The AD5450/AD5451/AD5452/AD5453 DACs are available in small 8-lead TSOT, and the AD5452/AD5453 are also available in MSOP packages. The AD5453 also comes in 8-lead LFCSP. U.S. Patent Number 5,689,257. Rev. H Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2005-2015 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD5450/AD5451/AD5452/AD5453 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 DAC Section................................................................................ 16 Applications ....................................................................................... 1 Circuit Operation ....................................................................... 16 Functional Block Diagram .............................................................. 1 Single-Supply Applications ....................................................... 18 General Description ......................................................................... 1 Adding Gain ................................................................................ 18 Revision History ............................................................................... 2 Divider or Programmable Gain Element ................................ 19 Specifications..................................................................................... 3 Reference Selection .................................................................... 19 Timing Characteristics ................................................................ 5 Amplifier Selection .................................................................... 19 Absolute Maximum Ratings ............................................................ 6 Serial Interface ............................................................................ 21 ESD Caution .................................................................................. 6 Microprocessor Interfacing ....................................................... 22 Pin Configurations and Function Descriptions ........................... 7 PCB Layout and Power Supply Decoupling ........................... 24 Typical Performance Characteristics ............................................. 8 Outline Dimensions ....................................................................... 26 Terminology .................................................................................... 15 Ordering Guide .......................................................................... 27 General Description ....................................................................... 16 Automotive Products ................................................................. 27 REVISION HISTORY 12/15--Rev. G to Rev. H Changed LFCSP_WD to LFCSP.................................. Throughout Changes to Applications Section and General Description Section .......................................................................... 1 Deleted Positive Output Voltage Section and Figure 47............ 18 Changes to Adding Gain Section ................................................. 19 Changes to ADSP-21xx Processors to AD5450/AD5451/AD5452/ AD5453 Interface Section and Figure 56 ....................................... 23 Changes to ADSP-BF504 to ADSP-BF592 Device Family to AD5450/AD5451/AD5452/AD5453 Interface Section, MC68HC11 to AD5450/AD5451/AD5452/AD5453 Interface Section, Figure 57 Caption, and Figure 58 Caption .................................. 24 Changes to PIC16C6x/PIC16C7x to AD5450/AD5451/AD5452/ AD5453 Interface Section .............................................................. 25 Changes to Table 13 Title............................................................... 26 Changes to Ordering Guide .......................................................... 29 6/13--Rev. F to Rev. G Change to General Description Section ........................................ 1 Change to Figure 56 and Figure 57 .............................................. 22 Updated Outline Dimensions ....................................................... 27 Changes to Ordering Guide .......................................................... 27 4/12--Rev. E to Rev. F Changes to General Description Section ...................................... 1 Deleted Evaluation Board for the DAC Section, Power Supplies for the Evaluation Board Section, and Figure 64; Renumbered Sequentially.............................................................. 25 Deleted Figure 65 and Figure 66................................................... 26 Deleted Figure 67 ............................................................................ 27 Changes to Ordering Guide .......................................................... 27 3/11--Rev. D to Rev. E Changes to SYNC Function Section ............................................ 21 Added Figure 54 (Renumbered Sequentially) ............................ 21 Added Figure 55 and Table 11 ..................................................... 22 2/11--Rev. C to Rev. D Added 8-Lead LFCSP......................................................... Universal Changes to Features Section ............................................................1 Updated Outline Dimensions ....................................................... 27 Changes to Ordering Guide .......................................................... 28 Added Automotive Products Section .......................................... 28 1/10--Rev. B to Rev. C Changes to DAC Control Bits C1, C0 .......................................... 21 Updated Outline Dimensions ....................................................... 27 Changes to Ordering Guide .......................................................... 28 3/06--Rev. A to Rev. B Updated Format .................................................................. Universal Changes to Features ..........................................................................1 Changes to General Description .....................................................1 Changes to Specifications .................................................................4 Changes to Figure 27 and Figure 28 ............................................ 11 Change to Table 9 ........................................................................... 20 Changes to Table 12 ....................................................................... 26 Updated Outline Dimensions ....................................................... 27 Changes to Ordering Guide .......................................................... 28 7/05--Rev. 0 to Rev. A Added AD5453 .................................................................... Universal Changes to Specifications .................................................................4 Change to Figure 21 ....................................................................... 10 Updated Outline Dimensions ....................................................... 27 Changes to Ordering Guide .......................................................... 28 1/05--Revision 0: Initial Version Rev. H | Page 2 of 28 Data Sheet AD5450/AD5451/AD5452/AD5453 SPECIFICATIONS VDD = 2.5 V to 5.5 V, VREF = 10 V. Temperature range for Y version: -40C to +125C. All specifications TMIN to TMAX, unless otherwise noted. DC performance measured with OP177 and ac performance measured with AD8038, unless otherwise noted. Table 1. Parameter STATIC PERFORMANCE AD5450 Resolution Relative Accuracy Differential Nonlinearity Total Unadjusted Error Gain Error AD5451 Resolution Relative Accuracy Differential Nonlinearity Total Unadjusted Error Gain Error AD5452 Resolution Relative Accuracy Differential Nonlinearity Total Unadjusted Error Gain Error AD5453 Resolution Relative Accuracy Differential Nonlinearity Total Unadjusted Error Gain Error Gain Error Temperature Coefficient 1 Output Leakage Current REFERENCE INPUT1 Reference Input Range VREF Input Resistance RFB Feedback Resistance Input Capacitance Zero-Scale Code Full-Scale Code DIGITAL INPUTS/OUTPUTS1 Input High Voltage, VIH Min Output Low Voltage, VOL Input Leakage Current, IIL Input Capacitance Max Unit Test Conditions/Comments 8 0.25 0.5 0.5 0.25 Bits LSB LSB LSB LSB Guaranteed monotonic 10 0.25 0.5 0.5 0.25 Bits LSB LSB LSB LSB Guaranteed monotonic 12 0.5 1 1 0.5 Bits LSB LSB LSB LSB Guaranteed monotonic 14 2 -1/+2 4 2.5 1 10 Bits LSB LSB LSB LSB ppm FSR/C nA nA 10 9 9 11 11 V k k 18 18 22 22 pF pF 2 7 7 2.0 1.7 Input Low Voltage, VIL Output High Voltage, VOH Typ 0.8 0.7 VDD - 1 VDD - 0.5 0.4 0.4 1 10 10 V V V V V V V V nA nA pF Rev. H | Page 3 of 28 Guaranteed monotonic Data = 0x0000, TA = 25C, IOUT1 Data = 0x0000, TA = -40C to +125C, IOUT1 Input resistance, TC = -50 ppm/C Input resistance, TC = -50 ppm/C VDD = 3.6 V to 5 V VDD = 2.5 V to 3.6 V VDD = 2.7 V to 5.5 V VDD = 2.5 V to 2.7 V VDD = 4.5 V to 5 V, ISOURCE = 200 A VDD = 2.5 V to 3.6 V, ISOURCE = 200 A VDD = 4.5 V to 5 V, ISINK = 200 A VDD = 2.5 V to 3.6 V, ISINK = 200 A TA = 25C TA = -40C to +125C AD5450/AD5451/AD5452/AD5453 Parameter DYNAMIC PERFORMANCE1 Reference Multiplying BW Multiplying Feedthrough Error Min Data Sheet Typ Max Unit Test Conditions/Comments 12 MHz 72 64 44 dB dB dB VREF = 3.5 V, DAC loaded with all 1s VREF = 3.5 V, DAC loaded with all 0s 100 kHz 1 MHz 10 MHz VREF = 10 V, RLOAD = 100 ; DAC latch alternately loaded with 0s and 1s Output Voltage Settling Time Measured to 1 mV of FS Measured to 4 mV of FS Measured to 16 mV of FS Digital Delay 10% to 90% Settling Time Digital-to-Analog Glitch Impulse Output Capacitance IOUT1 100 24 16 20 10 2 IOUT2 Digital Feedthrough Analog THD Digital THD 50 kHz fOUT 20 kHz fOUT Output Noise Spectral Density SFDR Performance (Wide Band) 50 kHz fOUT 20 kHz fOUT SFDR Performance (Narrow Band) 50 kHz fOUT 20 kHz fOUT Intermodulation Distortion POWER REQUIREMENTS Power Supply Range IDD 110 40 33 40 30 13 28 18 5 0.5 pF pF pF pF nV-s 83 dB 71 77 25 dB dB nV/Hz 78 74 dB dB Interface delay time Rise and fall times, VREF = 10 V, RLOAD = 100 1 LSB change around major carry, VREF = 0 V DAC latches loaded with all 0s DAC latches loaded with all 1s DAC latches loaded with all 0s DAC latches loaded with all 1s Feedthrough to DAC output with CS high and alternate loading of all 0s and all 1s VREF = 3.5 V p-p, all 1s loaded, f = 1 kHz Clock = 1 MHz, VREF = 3.5 V At 1 kHz Clock = 1 MHz, VREF = 3.5 V Clock = 1 MHz, VREF = 3.5 V 87 85 79 2.5 5.5 10 0.6 0.001 0.4 Power Supply Sensitivity1 1 ns ns ns ns ns nV-s dB dB dB f1 = 20 kHz, f2 = 25 kHz, clock = 1 MHz, VREF = 3.5 V V A A %/% TA = -40C to +125C, logic inputs = 0 V or VDD TA = 25C, logic inputs = 0 V or VDD VDD = 5% Guaranteed by design and characterization, not subject to production test. Rev. H | Page 4 of 28 Data Sheet AD5450/AD5451/AD5452/AD5453 TIMING CHARACTERISTICS All input signals are specified with tR = tF = 1 ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. VDD = 2.5 V to 5.5 V, VREF = 10 V, temperature range for Y version: -40C to +125C. All specifications TMIN to TMAX, unless otherwise noted. Table 2. Parameter 1 fSCLK t1 t2 t3 t4 t5 t6 t7 t8 Update Rate Unit MHz max ns min ns min ns min ns min ns min ns min ns min ns min MSPS Description Maximum clock frequency SCLK cycle time SCLK high time SCLK low time SYNC falling edge to SCLK active edge setup time Data setup time Data hold time SYNC rising edge to SCLK active edge Minimum SYNC high time Consists of cycle time, SYNC high time, data setup, and output voltage settling time Guaranteed by design and characterization, not subject to production test. t1 SCLK t2 t8 t3 t7 t4 SYNC t6 t5 DIN DB15 DB0 Figure 2. Timing Diagram Rev. H | Page 5 of 28 04587-002 1 VDD = 2.5 V to 5.5 V 50 20 8 8 8 5 4.5 5 30 2.7 AD5450/AD5451/AD5452/AD5453 Data Sheet ABSOLUTE MAXIMUM RATINGS Transient currents of up to 100 mA do not cause SCR latch-up. TA = 25C, unless otherwise noted. Table 3. Parameter VDD to GND VREF, RFB to GND IOUT1 to GND Input Current to Any Pin Except Supplies Logic Inputs and Output 1 Operating Temperature Range, Extended (Y Version) Storage Temperature Range Junction Temperature JA Thermal Impedance 8-Lead MSOP 8-Lead TSOT Lead Temperature, Soldering (10 sec) IR Reflow, Peak Temperature (<20 sec) 1 Rating -0.3 V to +7 V -12 V to +12 V -0.3 V to +7 V 10 mA -0.3 V to VDD + 0.3 V -40C to +125C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. ESD CAUTION -65C to +150C 150C 206C/W 211C/W 300C 235C Overvoltages at SCLK, SYNC, and SDIN are clamped by internal diodes. Rev. H | Page 6 of 28 Data Sheet AD5450/AD5451/AD5452/AD5453 RFB 1 VREF 2 VDD 3 SYNC 4 AD5450/ AD5451/ AD5452/ AD5453 8 IOUT1 7 GND 6 SCLK 5 SDIN 04587-003 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS IOUT1 1 GND 2 SCLK 3 AD5452/ AD5453 SDIN 4 8 RFB 7 VREF 6 VDD 5 SYNC 04587-004 Figure 3. 8-Lead TSOT Pin Configuration Figure 4. 8-Lead MSOP Pin Configuration AD5453 GND 2 SCLK 3 SDIN 4 TOP VIEW (Not to Scale) 8 RFB 7 VREF 6 VDD 5 SYNC NOTES 1. THE EXPOSED PAD MUST BE CONNECTED TO GROUND. 04587-205 IOUT1 1 Figure 5. 8-Lead LFCSP Pin Configuration Table 4. Pin Function Descriptions TSOT 1 Pin No1 MSOP LFCSP 8 8 Mnemonic RFB 2 3 4 7 6 5 7 6 5 VREF VDD SYNC 5 4 4 SDIN 6 3 3 SCLK 7 8 N/A 2 1 N/A 2 1 EPAD GND IOUT1 EPAD 1 Description DAC Feedback Resistor. Establish voltage output for the DAC by connecting to external amplifier output. DAC Reference Voltage Input. Positive Power Supply Input. These devices can operate from a supply of 2.5 V to 5.5 V. Active Low Control Input. This is the frame synchronization signal for the input data. Data is loaded to the shift register upon the active edge of the following clocks. Serial Data Input. Data is clocked into the 16-bit input register upon the active edge of the serial clock input. By default, in power-up mode data is clocked into the shift register upon the falling edge of SCLK. The control bits allow the user to change the active edge to a rising edge. Serial Clock Input. By default, data is clocked into the input shift register upon the falling edge of the serial clock input. Alternatively, by means of the serial control bits, the device can be configured such that data is clocked into the shift register upon the rising edge of SCLK. Ground Pin. DAC Current Output. Exposed pad must be connected to ground. N/A = not applicable. Rev. H | Page 7 of 28 AD5450/AD5451/AD5452/AD5453 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 0.25 2.0 TA = 25C VREF = 10V VDD = 5V 1.2 0.10 0.8 0.05 0.4 0 -0.05 0 -0.4 -0.10 -0.8 -0.15 -1.2 -0.20 -0.25 32 64 96 128 160 192 224 04587-023 INL (LSB) 0.15 0 TA = 25C VREF = 10V VDD = 5V 1.6 04587-020 INL (LSB) 0.20 -1.6 -2.0 0 256 2048 4096 6144 CODE Figure 6. INL vs. Code (8-Bit DAC) 0.5 TA = 25C VREF = 10V VDD = 5V 0.3 0.10 0.2 0.05 0.1 DNL (LSB) 0.15 0 -0.05 0 -0.1 -0.2 -0.15 -0.3 04587-021 -0.10 -0.20 -0.25 0 128 TA = 25C VREF = 10V VDD = 5V 0.4 256 384 512 640 768 896 04587-024 0.20 INL (LSB) 10240 12288 14336 16384 Figure 9. INL vs. Code (14-Bit DAC) 0.25 -0.4 -0.5 0 1024 32 64 96 CODE 128 160 192 224 256 896 1024 CODE Figure 7. INL vs. Code (10-Bit DAC) Figure 10. DNL vs. Code (8-Bit DAC) 0.5 0.5 TA = 25C VREF = 10V VDD = 5V 0.3 0.2 0.2 0.1 0.1 DNL (LSB) 0.3 0 -0.1 0 -0.1 -0.2 -0.3 -0.3 04587-022 -0.2 -0.4 -0.5 0 512 TA = 25C VREF = 10V VDD = 5V 0.4 1024 1536 2048 2560 3072 2584 04587-025 0.4 INL (LSB) 8192 CODE -0.4 -0.5 0 4096 128 256 384 512 640 768 CODE CODE Figure 8. INL vs. Code (12-Bit DAC) Figure 11. DNL vs. Code (10-Bit DAC) Rev. H | Page 8 of 28 Data Sheet AD5450/AD5451/AD5452/AD5453 2.0 1.0 TA = 25C VREF = 10V VDD = 5V 0.8 TA = 25C VDD = 5V AD5452 1.5 0.6 1.0 MAX DNL 0.5 0.2 DNL (LSB) DNL (LSB) 0.4 0 -0.2 0 MIN DNL -0.5 -0.4 -1.0 -0.6 -1.0 0 512 1024 1536 2048 2560 3072 2584 04587-071 -1.5 04587-026 -0.8 -2.0 4096 2 3 4 CODE Figure 12. DNL vs. Code (12-Bit DAC) 9 10 224 256 896 1024 Figure 15. DNL vs. Reference Voltage 0.5 2.0 TA = 25C VREF = 10V VDD = 5V 0.3 0.8 0.2 0.4 0.1 TUE (LSB) 1.2 0 -0.4 0 -0.1 -0.2 -1.2 -0.3 04587-027 -0.8 -1.6 -2.0 0 2048 TA = 25C VREF = 10V VDD = 5V AD5450 0.4 4096 6144 8192 04587-030 1.6 DNL (LSB) 5 6 7 8 REFERENCE VOLTAGE (V) -0.4 -0.5 10240 12288 14336 16384 0 32 64 96 CODE 128 160 192 CODE Figure 13. DNL vs. Code (14-Bit DAC) Figure 16. TUE vs. Code (8-Bit DAC) 1.00 0.25 TA = 25C VDD = 5V AD5452 0.75 TA = 25C VREF = 10V VDD = 5V AD5451 0.20 0.15 0.50 MAX INL 0.10 TUE (LSB) 0 MIN INL -0.25 0.05 0 -0.05 -0.10 -0.50 -1.00 2 3 4 5 6 7 8 REFERENCE VOLTAGE (V) 9 04587-031 -0.15 -0.75 04587-070 INL (LSB) 0.25 -0.20 -0.25 0 10 128 256 384 512 640 768 CODE Figure 14. INL vs. Reference Voltage Figure 17. TUE vs. Code (10-Bit DAC) Rev. H | Page 9 of 28 AD5450/AD5451/AD5452/AD5453 Data Sheet 1.0 0.3 TA = 25C VREF = 10V VDD = 5V 0.8 0.2 0.6 GAIN ERROR (LSB) 0.2 0 -0.2 -0.4 -0.6 0.1 VDD = 3V VDD = 5V 0 -0.1 04587-032 -0.2 -0.8 -1.0 0 512 1024 1536 2048 2560 3072 2584 04587-073 TUE (LSB) 0.4 -0.3 -60 4096 -40 Figure 18. TUE vs. Code (12-Bit DAC) 120 140 9 10 100 80 0 20 60 40 TEMPERATURE (C) -20 CODE Figure 21. Gain Error (LSB) vs. Temperature 2.0 2.0 TA = 25C VREF = 10V VDD = 5V 1.6 TA = 25C VDD = 5V AD5452 1.5 1.2 1.0 GAIN ERROR (LSB) INL (LSB) 0.8 0.4 0 -0.4 -0.8 0.5 0 -0.5 -1.0 -1.2 -2.0 0 2048 4096 6144 8192 04587-074 -1.5 04587-033 -1.6 -2.0 10240 12288 14336 16384 2 3 4 CODE Figure 19. TUE vs. Code (14-Bit DAC) Figure 22. Gain Error (LSB) vs. Reference Voltage 2.0 2.0 TA = 25C VDD = 5V AD5452 1.5 IOUT1 VDD = 5V 1.6 1.0 IOUT1 LEAKAGE (nA) MAX TUE 0.5 0 MIN TUE -0.5 -1.0 IOUT1 VDD = 3V 1.2 0.8 -2.0 2 3 4 6 7 5 8 REFERENCE VOLTAGE (V) 9 0 -40 10 04587-039 0.4 -1.5 04587-072 TUE (LSB) 6 7 5 8 REFERENCE VOLTAGE (V) -20 0 20 40 60 80 100 TEMPERATURE (C) Figure 20. TUE vs. Reference Voltage Figure 23. IOUT1 Leakage Current vs. Temperature Rev. H | Page 10 of 28 120 Data Sheet AD5450/AD5451/AD5452/AD5453 1.8 2.5 TA = 25C TA = 25C 1.6 VIH 1.5 1.0 VDD = 5V 04587-038 0.5 VDD = 3V 0 0 1 2 3 4 1.2 1.0 0.8 0.6 0.4 0.2 0 2.5 5 3.0 3.5 INPUT VOLTAGE (V) ALL 1s ALL 0s 0 0.6 5.0 5.5 -10 GAIN (dB) VDD = 5V 0.4 0.3 TA = 25C LOADING ZS TO FS ALL ON DB13 DB12 0.5 -20 DB11 DB10 -30 DB9 DB8 -40 DB7 DB6 -50 DB5 0.2 VDD = 3V 0 -40 04587-037 0.1 -20 0 20 40 60 80 100 -60 DB4 DB3 -70 DB2 -80 10k 120 VDD = 5V VREF = 3.5V CCOMP = 1.8pF AD8038 AMPLIFIER 100k TEMPERATURE (C) 1M 10M 04587-108 CURRENT (A) 4.5 10 0.7 100M FREQUENCY (Hz) Figure 25. Supply Current vs. Temperature Figure 28. Reference Multiplying Bandwidth vs. Frequency and Code 0.6 TA = 25C AD5452 LOADING 010101010101 5 4.0 VOLTAGE (V) Figure 27. Threshold Voltage vs. Supply Voltage Figure 24. Supply Current vs. Logic Input Voltage 6 VIL 1.4 04587-076 THRESHOLD VOLTAGE (V) CURRENT (mA) 2.0 0.4 4 3 GAIN (dB) 0 VDD = 5V 2 -0.2 -0.4 -0.6 VDD = 3V 0 1 10 100 1k 10k 100k 1M -1.0 TA = 25C VDD = 5V VREF = 3.5V CCOMP = 1.8pF AD8038 AMPLIFIER -1.2 10k 10M FREQUENCY (Hz) 100k 04587-109 -0.8 1 04587-075 CURRENT (mA) 0.2 1M 10M 100M FREQUENCY (Hz) Figure 26. Supply Current vs. Update Rate Figure 29. Reference Multiplying Bandwidth--All 1s Loaded Rev. H | Page 11 of 28 AD5450/AD5451/AD5452/AD5453 Data Sheet 3 10 TA = 25C VDD = 5V TA = 25C VDD = 3V AD8038 AMPLIFIER 0 -10 0 -20 PSRR (dB) GAIN (dB) -30 -3 -40 FULL SCALE -50 -60 -80 10M 1M 100k ZERO SCALE -70 = 2V, AD8038 C COMP = 1pF = 2V, AD8038 C COMP = 1.5pF = 15V, AD8038 C COMP = 1pF = 15V, AD8038 C COMP = 1.5pF = 15V, AD8038 C COMP = 1.8pF 04587-082 -9 10k VREF VREF VREF VREF VREF 04587-079 -6 -90 -100 100M 1 10 100 1k FREQUENCY (Hz) 1M 10M -60 0.08 TA = 25C VDD = 0V AD8038 AMPLIFIER CCOMP = 1.8pF VDD = 5V 0x7FF TO 0x800 NRG = 2.154nVs -65 VDD = 3V 0x7FF TO 0x800 NRG = 1.794nVs -70 THD + N (dB) 0.04 0.02 0 -0.04 -85 04587-080 VDD = 5V 0x800 TO 0x7FF NRG = 0.694nVs -0.06 50 75 100 125 150 -75 -80 VDD = 5V 0x800 TO 0x7FF NRG = 0.694nVs -0.02 TA = 25C VDD = 5V VREF = 3.5V 175 200 225 04587-083 0.06 -90 100 250 1k 10k 100k FREQUENCY (Hz) TIME (ns) Figure 34. THD + Noise vs. Frequency Figure 31. Midscale Transition, VREF = 0 V 100 -1.66 TA = 25C VDD = 3.5V AD8038 AMPLIFIER CCOMP = 1.8pF VDD = 5V 0x7FF TO 0x800 NRG = 2.154nVs -1.68 VDD = 3V 0x7FF TO 0x800 NRG = 1.794nVs MCLK = 1MHz SFDR (dB) -1.70 -1.72 -1.74 -1.76 VDD = 5V 0x800 TO 0x7FF NRG = 0.694nVs VDD = 5V 0x800 TO 0x7FF NRG = 0.694nVs -1.80 50 75 100 125 150 60 40 20 04587-081 -1.78 MCLK = 200kHz MCLK = 500kHz 80 175 200 225 TA = 25C VREF = 3.5V AD8038 AMPLIFIER 0 0 250 04587-084 OUTPUT VOLTAGE (V) 100k Figure 33. Power Supply Rejection Ratio vs. Frequency Figure 30. Reference Multiplying Bandwidth vs. Frequency and Compensation Capacitor OUTPUT VOLTAGE (V) 10k FREQUENCY (Hz) 10 20 30 40 fOUT (kHz) TIME (ns) Figure 35. Wideband SFDR vs. fOUT Frequency Figure 32. Midscale Transition, VREF = 3.5 V Rev. H | Page 12 of 28 50 Data Sheet AD5450/AD5451/AD5452/AD5453 0 0 TA = 25C VDD = 5V VREF = 3.5V AD8038 AMPLIFIER -20 -20 -40 -40 SFDR (dB) -60 -60 -80 -100 -100 04587-085 -80 -120 0 100k 300k 200k 400k -120 30k 500k 04587-088 SFDR (dB) TA = 25C VDD = 5V VREF = 3.5V AD8038 AMPLIFIER Figure 39. Narrow-Band SFDR , fOUT = 50 kHz, Clock = 1 MHz 0 0 TA = 25C VDD = 5V VREF = 3.5V AD8038 AMPLIFIER -20 TA = 25C VREF = 3.5V AD8038 AMPLIFIER -10 -20 -30 -40 -40 IMD (dB) -60 -50 -60 -80 -70 -80 04587-086 -100 -120 0 100k 200k 300k 400k 04587-089 SFDR (dB) 70k FREQUENCY (Hz) Figure 36. Wideband SFDR, fOUT = 20 kHz, Clock = 1 MHz -90 -100 10k 500k 15k FREQUENCY (Hz) 20k 25k 30k 35k FREQUENCY (Hz) Figure 37. Wideband SFDR, fOUT = 50 kHz, Clock = 1 MHz Figure 40. Narrow-Band IMD, fOUT = 20 kHz, 25 kHz, Clock = 1 MHz 0 0 TA = 25C VDD = 5V VREF = 3.5V AD8038 AMPLIFIER -20 TA = 25C VREF = 3.5V AD8038 AMPLIFIER -10 -20 -30 IMD (dB) -40 SFDR (dB) 60k 50k 40k FREQUENCY (Hz) -60 -40 -50 -60 -80 -70 -120 10k 04587-087 -100 15k 20k 25k 04587-090 -80 -90 -100 30k 0 FREQUENCY (Hz) 100k 200k 300k 400k 500k FREQUENCY (Hz) Figure 38. Narrow-Band SFDR, fOUT = 20 kHz, Clock = 1 MHz Figure 41. Wideband IMD, fOUT = 20 kHz, 25 kHz, Clock = 1 MHz | Rev. H | Page 13 of 28 AD5450/AD5451/AD5452/AD5453 Data Sheet 80 TA = 25C AD8038 AMPLIFIER 60 FULL SCALE LOADED TO DAC 50 40 MIDSCALE LOADED TO DAC 30 20 ZERO SCALE LOADED TO DAC 10 0 100 1k 10k 100k 04587-091 OUTPUT NOISE (nV/ Hz) 70 1M FREQUENCY (Hz) Figure 42. Output Noise Spectral Density Rev. H | Page 14 of 28 Data Sheet AD5450/AD5451/AD5452/AD5453 TERMINOLOGY Relative Accuracy (Endpoint Nonlinearity) A measure of the maximum deviation from a straight line passing through the endpoints of the DAC transfer function. It is measured after adjusting for zero and full scale and is normally expressed in LSBs or as a percentage of the full-scale reading. Digital Feedthrough When the device is not selected, high frequency logic activity on the device's digital inputs may be capacitively coupled through the device and produce noise on the IOUT pins. This noise is coupled from the outputs of the device onto follow on circuitry. This noise is digital feedthrough. Differential Nonlinearity The difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of -1 LSB maximum over the operating temperature range ensures monotonicity. Multiplying Feedthrough Error The error due to capacitive feedthrough from the DAC reference input to the DAC IOUT1 terminal when all 0s are loaded to the DAC. Gain Error (Full-Scale Error) A measure of the output error between an ideal DAC and the actual device output. For these DACs, ideal maximum output is VREF - 1 LSB. Gain error of the DACs is adjustable to zero with external resistance. Total Harmonic Distortion (THD) The DAC is driven by an ac reference. The ratio of the rms sum of the harmonics of the DAC output to the fundamental value is the THD. Usually only the lower-order harmonics, such as second to fifth, are included. Output Leakage Current The current that flows into the DAC ladder switches when it is turned off. For the IOUT1 terminal, it can be measured by loading all 0s to the DAC and measuring the IOUT1 current. Output Capacitance Capacitance from IOUT1 to AGND. Output Current Settling Time The amount of time it takes for the output to settle to a specified level for a full-scale input change. For these devices, it is specified with a 100 resistor to ground. The settling time specification includes the digital delay from the SYNC rising edge to the fullscale output change. Digital-to-Analog Glitch Impulse The amount of charge injected from the digital inputs to the analog output when the inputs change state. This is normally specified as the area of the glitch in either pA-s or nV-s, depending on whether the glitch is measured as a current or voltage signal. THD = 20 log V 2 2 + V3 2 + V 4 2 + V5 2 V1 Digital Intermodulation Distortion (IMD) Second-order intermodulation measurements are the relative magnitudes of the fa and fb tones generated digitally by the DAC and the second-order products at 2fa - fb and 2fb - fa. Compliance Voltage Range The maximum range of (output) terminal voltage for which the device provides the specified characteristics. Spurious-Free Dynamic Range (SFDR) The usable dynamic range of a DAC before spurious noise interferes or distorts the fundamental signal. SFDR is the measure of difference in amplitude between the fundamental and the largest harmonically or nonharmonically related spur from dc to full Nyquist bandwidth (half the DAC sampling rate or fS/2). Narrow band SFDR is a measure of SFDR over an arbitrary window size, in this case 50% of the fundamental. Digital SFDR is a measure of the usable dynamic range of the DAC when the signal is a digitally generated sine wave. Rev. H | Page 15 of 28 AD5450/AD5451/AD5452/AD5453 Data Sheet GENERAL DESCRIPTION DAC SECTION VDD The AD5450/AD5451/AD5452/AD5453 are 8-/10-/12-/14-bit current output DACs, respectively, consisting of a segmented (4-bit) inverting R-2R ladder configuration. A simplified diagram for the 12-bit AD5452 is shown in Figure 43. R R VDD VREF VREF R1 R2 AD5450/ AD5451/ AD5452/ AD5453 C1 RFB IOUT1 A1 GND VOUT = 0 TO -VREF SYNC SCLK SDIN R VREF AGND 2R 2R 2R S1 S2 S3 S12 2R R CONTROLLER RFB NOTES 1. R1 AND R2 USED ONLY IF GAIN ADJUSTMENT IS REQUIRED. 2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED IF A1 IS A HIGH SPEED AMPLIFIER. DAC DATA LATCHES AND DRIVERS AGND 04587-060 IOUT1 Figure 44. Unipolar Mode Operation Figure 43. AD5452 Simplified Ladder The feedback resistor, RFB, has a value of R. The value of R is typically 9 k (with a minimum value of 7 k and a maximum value of 11 k). If IOUT1 is kept at the same potential as GND, a constant current flows in each ladder leg, regardless of digital input code. Therefore, the input resistance presented at VREF is always constant and nominally of value R. The DAC output (IOUT1) is code dependent, producing various resistances and capacitances. When choosing the external amplifier, take into account the variation in impedance generated by the DAC on the amplifier's inverting input node. Access is provided to the VREF, RFB, and IOUT1 terminals of the DAC, making the device extremely versatile and allowing it to be configured in several operating modes; for example, it can provide a unipolar output or can provide 4-quadrant multiplication in bipolar mode. Note that a matching switch is used in series with the internal RFB feedback resistor. If users attempt to measure RFB, power must be applied to VDD to achieve continuity. CIRCUIT OPERATION These DACs are designed to operate with either negative or positive reference voltages. The VDD power pin is only used by the internal digital logic to drive the on and off states of the DAC switches. These DACs are designed to accommodate ac reference input signals in the range of -10 V to +10 V. With a fixed 10 V reference, the circuit shown in Figure 44 gives a unipolar 0 V to -10 V output voltage swing. When VIN is an ac signal, the circuit performs 2-quadrant multiplication. Table 5 shows the relationship between the digital code and the expected output voltage for a unipolar operation using the 8-bit AD5450. Table 5. Unipolar Code Table for the AD5450 Digital Input 1111 1111 1000 0000 0000 0001 0000 0000 Unipolar Mode Using a single operational amplifier, these devices can easily be configured to provide a 2-quadrant multiplying operation or a unipolar output voltage swing, as shown in Figure 44. When an output amplifier is connected in unipolar mode, the output voltage is given by VOUT = - 04587-009 2R D x V REF 2n where: D is the fractional representation of the digital word loaded to the DAC. D = 0 to 255 (8-bit AD5450). = 0 to 1023 (10-bit AD5451). = 0 to 4095 (12-bit AD5452). = 0 to 16,383 (14-bit AD5453). n is the number of bits. Note that the output voltage polarity is opposite to the VREF polarity for dc reference voltages. Rev. H | Page 16 of 28 Analog Output (V) -VREF (255/256) -VREF (128/256) = -VREF/2 -VREF (1/256) -VREF (0/256) = 0 Data Sheet AD5450/AD5451/AD5452/AD5453 When VIN is an ac signal, the circuit performs 4-quadrant multiplication. Table 6 shows the relationship between the digital code and the expected output voltage for a bipolar operation using the 8-bit AD5450. Bipolar Mode In some applications, it may be necessary to generate a full 4-quadrant multiplying operation or a bipolar output swing. This can be easily accomplished by using another external amplifier and some external resistors, as shown in Figure 45. In this circuit, the second amplifier, A2, provides a gain of 2. Biasing the external amplifier with an offset from the reference voltage results in full 4-quadrant multiplying operation. The transfer function of this circuit shows that both negative and positive output voltages are created as the input data (D) is incremented from Code 0 (VOUT = - VREF) to midscale (VOUT - 0 V ) to full scale (VOUT = +VREF). Table 6. Bipolar Code Table for the AD5450 Digital Input 1111 1111 1000 0000 0000 0001 0000 0000 Analog Output (V) +VREF (127/128) 0 -VREF (127/128) -VREF (128/128) Stability In the I-to-V configuration, the IOUT of the DAC and the inverting node of the operational amplifier must be connected as close as possible, and proper printed circuit board (PCB) layout techniques must be employed. Because every code change corresponds to a step function, gain peaking may occur if the operational amplifier has limited gain bandwidth product (GBP) and there is excessive parasitic capacitance at the inverting node. This parasitic capacitance introduces a pole into the open-loop response, which can cause ringing or instability in the closedloop applications circuit. D VOUT = VREF x n -1 - VREF 2 where: D is the fractional representation of the digital word loaded to the DAC. D = 0 to 255 (8-bit AD5450). = 0 to 1023 (10-bit AD5451). = 0 to 4095 (12-bit AD5452). n is the resolution of the DAC. An optional compensation capacitor, C1, can be added in parallel with RFB for stability, as shown in Figure 44 and Figure 45. Too small a value of C1 can produce ringing at the output, and too large a value can adversely affect the settling time. C1 should be found empirically, but 1 pF to 2 pF is generally adequate for the compensation. R3 20k VDD VDD VREF 10V VREF R1 R5 20k R2 AD5450/ AD5451/ AD5452/ AD5453 C1 RFB IOUT1 A1 R4 10k A2 GND VOUT = -VREF TO +VREF SYNC SCLK SDIN AGND Figure 45. Bipolar Mode Operation (4-Quadrant Multiplication) Rev. H | Page 17 of 28 04587-010 CONTROLLER NOTES 1. R1 AND R2 USED ONLY IF GAIN ADJUSTMENT IS REQUIRED. ADJUST R1 FOR VOUT = 0V WITH CODE 10000000 LOADED TO DAC. 2. MATCHING AND TRACKING IS ESSENTIAL FOR RESISTOR PAIRS R3 AND R4. 3. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED IF A1/A2 IS A HIGH SPEED AMPLIFIER. AD5450/AD5451/AD5452/AD5453 Data Sheet SINGLE-SUPPLY APPLICATIONS ADDING GAIN Voltage Switching Mode In applications in which the output voltage is required to be greater than VIN, gain can be added with an additional external amplifier, or it can be achieved in a single stage. It is important to consider the effect of the temperature coefficients of the DAC thin film resistors. Simply placing a resistor in series with the RFB resistor causes mismatches in the temperature coefficients and results in larger gain temperature coefficient errors. Instead, increase the gain of the circuit by using the recommended configuration shown in Figure 47. R1, R2, and R3 must have similar temperature coefficients, but they need not match the temperature coefficients of the DAC. This approach is recommended in circuits where gains greater than 1 are required. Note that RFB R2//R3 and a gain error percentage of 100 x (R2//R3)/RFB must be taken into consideration. Figure 46 shows these DACs operating in the voltage switching mode. The reference voltage, VIN, is applied to the IOUT1 pin, and the output voltage is available at the VREF terminal. In this configuration, a positive reference voltage results in a positive output voltage, making single-supply operation possible. The output from the DAC is voltage at a constant impedance (the DAC ladder resistance); therefore, an operational amplifier is necessary to buffer the output voltage. The reference input no longer sees constant input impedance, but one that varies with code; therefore, drive the voltage input from a low impedance source. VDD RFB R2 VDD IOUT1 VDD VOUT VREF VDD GND VIN R1 IOUT1 VREF VOUT R3 04587-011 NOTES 1. ADDITIONAL PINS OMITTED FOR CLARITY. 2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED IF A1 IS A HIGH SPEED AMPLIFIER. C1 RFB GND R2 Figure 46. Single-Supply Voltage Switching Mode It is important to note that with this configuration VIN is limited to low voltages because the switches in the DAC ladder do not have the same source-drain drive voltage. As a result, the on resistance of the switches differs, which degrades the integral linearity of the DAC. Also, VIN must not go negative by more than 0.3 V, or an internal diode turns on, causing the device to exceed the maximum ratings. In this type of application, the full range of multiplying capability of the DAC is lost. GAIN = R2 + R3 R2 R2R3 R1 = NOTES R2 + R3 1. ADDITIONAL PINS OMITTED FOR CLARITY. 2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED IF A1 IS A HIGH SPEED AMPLIFIER. Rev. H | Page 18 of 28 Figure 47. Increasing Gain of Current-Output DAC 04587-013 VIN R1 Data Sheet AD5450/AD5451/AD5452/AD5453 DIVIDER OR PROGRAMMABLE GAIN ELEMENT Current-steering DACs are very flexible and lend themselves to many different applications. If this type of DAC is connected as the feedback element of an operational amplifier and RFB is used as the input resistor as shown in Figure 48, the output voltage is inversely proportional to the digital input fraction, D. For D = 1 - 2 , the output voltage is -n VOUT = -VIN -VIN = (1 - 2 -n ) D As D is reduced, the output voltage increases. For small values of the digital fraction, D, it is important to ensure that the amplifier does not saturate and that the required accuracy is met. For example, an 8-bit DAC driven with the binary code 0x10 (00010000), that is, 16 decimal, in the circuit of Figure 48 causes the output voltage to be 16 times VIN. VDD VIN RFB VDD IOUT1 VREF GND NOTE ADDITIONAL PINS OMITTED FOR CLARITY 04587-014 VOUT Figure 48. Current Steering DAC Used as a Divider or Programmable Gain Element However, if the DAC has a linearity specification of 0.5 LSB, D can have weight anywhere in the range of 15.5/256 to 16.5/256. Therefore, the possible output voltage is in the range of 15.5 VIN to 16.5 VIN--an error of 3%, even though the DAC itself has a maximum error of 0.2%. DAC leakage current is also a potential error source in divider circuits. The leakage current must be counterbalanced by an opposite current supplied from the operational amplifier through the DAC. Because only a fraction, D, of the current in the VREF terminal is routed to the IOUT1 terminal, the output voltage changes as follows: Output Error Voltage Dueto Leakage = (Leakage x R)/D where R is the DAC resistance at the VREF terminal. For a DAC leakage current of 10 nA, R = 10 k, and a gain (that is, 1/D) of 16, the error voltage is 1.6 mV. REFERENCE SELECTION When selecting a reference for use with this series of current output DACs, pay attention to the reference's output voltage temperature coefficient specification. This parameter not only affects the full-scale error, but also may affect the linearity (INL and DNL) performance. The reference temperature coefficient should be consistent with the system accuracy specifications. For example, an 8-bit system is required to hold its overall specification to within 1 LSB over the temperature range 0C to 50C, and the system's maximum temperature drift should be less than 78 ppm/C. A 12-bit system within 2 LSB accuracy requires a maximum drift of 10 ppm/C. Choosing a precision reference with a low output temperature coefficient minimizes this error source. Table 7 lists some dc references available from Analog Devices, Inc., that are suitable for use with this range of current output DACs. AMPLIFIER SELECTION The primary requirement for the current steering mode is an amplifier with low input bias currents and low input offset voltage. The input offset voltage of an operational amplifier is multiplied by the variable gain of the circuit due to the code dependent output resistance of the DAC. A change in this noise gain between two adjacent digital fractions produces a step change in the output voltage due to the offset voltage of the amplifier's input. This output voltage change is superimposed on the desired change in output between the two codes and gives rise to a differential linearity error, which if large enough, could cause the DAC to be nonmonotonic. The input bias current of an operational amplifier generates an offset at the voltage output as a result of the bias current flowing in the feedback resistor, RFB. Most operational amplifiers have input bias currents low enough to prevent significant errors in 12-bit applications. However, for 14-bit applications, some consideration should be given to selecting an appropriate amplifier. Common-mode rejection of the operational amplifier is important in voltage switching circuits because it produces a code-dependent error at the voltage output of the circuit. Most operational amplifiers have adequate common-mode rejection for use at 8-, 10-, and 12-bit resolutions. Provided that the DAC switches are driven from true wideband low impedance sources (VIN and AGND), they settle quickly. Consequently, the slew rate and settling time of a voltage switching DAC circuit is determined largely by the output operational amplifier. To obtain minimum settling time in this configuration, it is important to minimize capacitance at the VREF node (the voltage output node in this application) of the DAC. This is done by using low input capacitance buffer amplifiers and careful board design. Most single-supply circuits include ground as part of the analog signal range, which in turn requires an amplifier that can handle rail-to-rail signals. There is a large range of single-supply amplifiers available from Analog Devices. Rev. H | Page 19 of 28 AD5450/AD5451/AD5452/AD5453 Data Sheet Table 7. Suitable Analog Devices Precision References Part No. ADR01 ADR01 ADR02 ADR02 ADR03 ADR03 ADR06 ADR06 ADR431 ADR435 ADR391 ADR395 Output Voltage (V) 10 10 5 5 2.5 2.5 3 3 2.5 5 2.5 5 Initial Tolerance (%) 0.05 0.05 0.06 0.06 0.10 0.10 0.10 0.10 0.04 0.04 0.16 0.10 Temp Drift (ppm/C) 3 9 3 9 3 9 3 9 3 3 9 9 ISS (mA) 1 1 1 1 1 1 1 1 0.8 0.8 0.12 0.12 Output Noise (V p-p) 20 20 10 10 6 6 10 10 3.5 8 5 8 Package SOIC-8 TSOT-23, SC70 SOIC-8 TSOT-23, SC70 SOIC-8 TSOT-23, SC70 SOIC-8 TSOT-23, SC70 SOIC-8 SOIC-8 TSOT-23 TSOT-23 Table 8. Suitable Analog Devices Precision Operational Amplifier Part No. OP97 OP1177 AD8551 AD8603 AD8628 Supply Voltage (V) 2 to 20 2.5 to 15 2.7 to 5 1.8 to 6 2.7 to 6 VOS (Max) (V) 25 60 5 50 5 IB (Max) (nA) 0.1 2 0.05 0.001 0.1 0.1 Hz to 10 Hz Noise (V p-p) 0.5 0.4 1 2.3 0.5 Supply Current (A) 600 500 975 50 850 Package SOIC-8 MSOP, SOIC-8 MSOP, SOIC-8 TSOT TSOT, SOIC-8 Table 9. Suitable Analog Devices High Speed Operational Amplifier Part No. AD8065 AD8021 AD8038 AD9631 Supply Voltage (V) 5 to 24 2.5 to 12 3 to 12 3 to 6 BW at ACL (MHz) 145 490 350 320 Slew Rate (V/s) 180 120 425 1300 Rev. H | Page 20 of 28 VOS (Max) (V) 1500 1000 3000 10000 IB (Max) (nA) 0.006 10500 750 7000 Package SOIC-8, SOT-23, MSOP SOIC-8, MSOP SOIC-8, SC70-5 SOIC-8 Data Sheet AD5450/AD5451/AD5452/AD5453 SERIAL INTERFACE SYNC Function The AD5450/AD5451/AD5452/AD5453 have an easy to use 3-wire interface that is compatible with SPI, QSPI, MICROWIRE, and most DSP interface standards. Data is written to the device in 16-bit words. This 16-bit word consists of two control bits and 8, 10, 12, or 14 data bits, as shown in Figure 49, Figure 50, Figure 51, and Figure 52. The AD5453 uses all 14 bits of DAC data, the AD5452 uses 12 bits and ignores the two LSBs, the AD5451 uses 10 bits and ignores the four LSBs, and the AD5450 uses 8 bits and ignores the six LSBs. SYNC is an edge triggered input that acts as a frame synchronization signal and chip enable. Data can only be transferred to the device while SYNC is low. To start the serial data transfer, SYNC should be taken low, observing the minimum SYNC falling to SCLK falling edge setup time, t4. To minimize the power consumption of the device, the interface powers up fully only when the device is being written to, that is, upon the falling edge of SYNC. The SCLK and SDIN input buffers are powered down upon the rising edge of SYNC. DAC Control Bits C1, C0 After the falling edge of the 16th SCLK pulse, bring SYNC high to transfer data from the input shift register to the DAC register. Control Bits C1 and C0 allow the user to load and update the new DAC code and to change the active clock edge. By default, the shift register clocks data upon the falling edge; this can be changed via the control bits. If changed, the DAC core is inoperative until the next data frame, and a power recycle is required to return it to active on the falling edge. A power cycle resets the core to default condition. On-chip power-on reset circuitry ensures that the device powers on with zero scale loaded to the DAC register and IOUT line. The serial interface to the AD5450 uses a 16-bit shift register. Take care to avoid incomplete data sequences as these will be latched to update the DAC output. For example, * * Table 10. DAC Control Bits Function Implemented Load and update (power-on default) Reserved Reserved Clock data to shift register upon rising edge * Also note that if more then 16-bits are loaded to the device before SYNC goes high the last 16-bits will be latched. DB15 (MSB) C0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 X X X X X X 04587-005 C1 DB0 (LSB) DATA BITS CONTROL BITS Figure 49. AD5450 8-Bit Input Shift Register Contents DB15 (MSB) C0 DB0 (LSB) DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 X X X X 04587-006 C1 DATA BITS CONTROL BITS Figure 50. AD5451 10-Bit Input Shift Register Contents DB15 (MSB) C1 C0 DB0 (LSB) DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 X X 04587-007 C0 0 1 0 1 DATA BITS CONTROL BITS Figure 51. AD5452 12-Bit Input Shift Register Contents DB15 (MSB) C1 C0 DB0 (LSB) DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DATA BITS CONTROL BITS Figure 52. AD5453 14-Bit Input Shift Register Contents Rev. H | Page 21 of 28 04587-008 C1 0 0 1 1 Loading 0x3FFF (a complete data sequence) will update the output to 10 V (full scale). User intends to write 0x3200 but after 12 active edges SYNC goes high (incomplete write sequence). This will update the following code: 0xF200. The user expects an output of 5.6 V. However, if SYNC goes high after 12 valid clock edges then an incomplete data sequence of 12 bits is loaded. To complete the shift register the 4 LSBs from the previous sequence are taken and used as the 4 MSBs missing. The addition of these 4 bits will put the device in rising edge mode and the output will show no change. Figure 53, Figure 54, and Table 11 show the data frames for this example. AD5450/AD5451/AD5452/AD5453 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 04587-054 0 Data Sheet DATA BITS CONTROL BITS Figure 53. AD5453 First Write, Complete Data Sequence (0x3FFF) 0 1 1 0 0 1 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 1 DATA BITS 0 0 0 0 0 0 0 0 0 DATA BITS CONTROL BITS 04587-055 0 CONTROL BITS INTENDED DATA FRAME ACTUAL DATA FRAME Figure 54. AD5453 Second Write, Incomplete Data Sequence (0x3200) and Subsequent Additional Bits (0xF200) Table 11. Data Write in Shift Register 0x3FFF 0x3200 Action Expected Load and update 0x3FFF Load and update 0x3200 Data Transfer to the Device 0x3FFF 0xF200 MICROPROCESSOR INTERFACING Table 12. SPORT Control Register Setup 04587-100 SCLK *ADDITIONAL PINS OMITTED FOR CLARITY Figure 55. ADSP-2191M SPI to AD5450/AD5451/AD5452/AD5453 Interface SCLK Figure 56. ADSP-2191M to AD5450/AD5451/AD5452/AD5453 Interface SYNC SDIN SDIN Communication between two devices at a given clock speed is possible when the following specifications are compatible: frame SYNC delay and frame SYNC setup and hold, data delay and data setup and hold, and SCLK width. The DAC interface expects a t4 (SYNC falling edge to SCLK falling edge setup time) of 13 ns minimum. See the ADSP-21xx device family for information on clock and frame SYNC frequencies for the SPORT register. Table 12 shows the setup for the SPORT control register. AD5450/AD5451/ AD5452/AD5453* SCK SYNC DT *ADDITIONAL PINS OMITTED FOR CLARITY The ADSP-21xx device family of DSPs is easily interfaced to a AD5450/AD5451/AD5452/AD5453 DAC without the need for extra glue logic. Figure 55 is an example of an SPI interface between the DAC and the ADSP-2191M. SCK of the DSP drives the serial data line, SDIN. SYNC is driven from one of the port lines, in this case SPIxSEL. MOSI TFS SCLK ADSP-21xx Processors to AD5450/AD5451/AD5452/ AD5453 Interface SPIxSEL AD5450/AD5451/ AD5452/AD5453* ADSP-2191M* Microprocessor interfacing to a AD5450/AD5451/AD5452/ AD5453 DAC is through a serial bus that uses standard protocol and is compatible with microcontrollers and DSP processors. The communication channel is a 3-wire interface consisting of a clock signal, a data signal, and a synchronization signal. The AD5450/AD5451/AD5452/AD5453 require a 16-bit word, with the default being data valid upon the falling edge of SCLK, but this is changeable using the control bits in the data-word. ADSP-2191M* Action Carried Out Load and update 0x3FFF Clock data to shift register upon rising edge (0xF200) Name TFSW INVTFS DTYPE ISCLK TFSR ITFS SLEN A serial interface between the DAC and DSP SPORT is shown in Figure 56. In this example, SPORT0 is used to transfer data to the DAC shift register. Transmission is initiated by writing a word to the Tx register after the SPORT has been enabled. In a write sequence, data is clocked out upon each rising edge of the DSP's serial clock and clocked into the DAC input shift register upon the falling edge of its SCLK. The update of the DAC output takes place upon the rising edge of the SYNC signal. Rev. H | Page 22 of 28 Setting 1 1 00 1 1 1 1111 Description Alternate framing Active low frame signal Right justify data Internal serial clock Frame every word Internal framing signal 16-bit data-word 04587-051 Writing Sequence 1 2 Data Sheet AD5450/AD5451/AD5452/AD5453 The ADSP-BF504 to ADSP-BF592 device family of processors has an SPI-compatible port that enables the processor to communicate with SPI-compatible devices. A serial interface between the BlackFin(R) processor and the AD5450/AD5451/AD5452/AD5453 DAC is shown in Figure 57. In this configuration, data is transferred through the MOSI (master output, slave input) pin. SYNC is driven by the SPIxSEL pin, which is a reconfigured programmable flag pin. SYNC SDIN SCK SCLK 04587-102 MOSI *ADDITIONAL PINS OMITTED FOR CLARITY The ADSP-BF504 to ADSP-BF592 processors incorporate channel synchronous serial ports (SPORT). A serial interface between the DAC and the DSP SPORT is shown in Figure 58. When the SPORT is enabled, initiate transmission by writing a word to the Tx register. The data is clocked out upon each rising edge of the DSP's serial clock and clocked into the DAC's input shift register upon the falling edge its SCLK. The DAC output is updated by using the transmit frame synchronization (TFS) line to provide a SYNC signal. AD5450/AD5451/ AD5452/AD5453* TFS SYNC DT SDIN SCLK *ADDITIONAL PINS OMITTED FOR CLARITY 04587-103 SCLK SCLK SDIN P1.1 SYNC *ADDITIONAL PINS OMITTED FOR CLARITY Figure 59. 80C51/80L51 to AD5450/AD5451/AD5452/AD5453 Interface MC68HC11 to AD5450/AD5451/AD5452/AD5453 Interface Figure 57. ADSP-BF504 to ADSP-BF592 Device Family to AD5450/AD5451/AD5452/AD5453 Interface (ADSP-BFxx Denotes the ADSP-BF504 to ADSP-BF592) ADSP-BF5xx* TxD RxD Figure 60 is an example of a serial interface between the DAC and the MC68HC11 microcontroller (Motorola). The serial peripheral interface (SPI) on the MC68HC11 is configured for master mode (MSTR) = 1, clock polarity bit (CPOL) = 0, and clock phase bit (CPHA) = 1. The SPI is configured by writing to the SPI control register (SPCR). SCK of the 68HC11 drives the SCLK of the DAC interface; the MOSI output drives the serial data line (SDIN) of the DAC. The SYNC signal is derived from a port line (PC7). When data is being transmitted to the AD5450/AD5451/AD5452/AD5453, the SYNC line is taken low (PC7). Data appearing on the MOSI output is valid upon the falling edge of SCK. Serial data from the 68HC11 is transmitted in 8-bit bytes with only eight falling clock edges occurring in the transmit cycle. Data is transmitted MSB first. To load data to the DAC, PC7 is left low after the first eight bits are transferred, and a second serial write operation is performed to the DAC. PC7 is taken high at the end of this procedure. AD5450/AD5451/ AD5452/AD5453* MC68HC11* Figure 58. ADSP-BF504 to ADSP-BF592 Device Family SPORT to AD5450/AD5451/AD5452/AD5453 Interface (ADSP-BFxx Denotes the ADSP-BF504 to ADSP-BF592) PC7 80C51/80L51 to AD5450/AD5451/AD5452/AD5453 Interface A serial interface between the DAC and the 80C51/80L51 is shown in Figure 59. TxD of the 80C51/80L51 drives SCLK of the DAC serial interface, and RxD drives the serial data line, SDIN. P1.1 is a bit-programmable pin on the serial port and is used to drive SYNC. As data is transmitted to the switch, P1.1 is taken low. The 80C51/80L51 transmit data only in 8-bit bytes; therefore, only eight falling clock edges occur in the transmit cycle. SYNC SCK SCLK MOSI SDIN *ADDITIONAL PINS OMITTED FOR CLARITY Figure 60. MC68HC11 to AD5450/AD5451/AD5452/AD5453 Interface If the user wants to verify the data previously written to the input shift register, the SDO line can be connected to MISO of the MC68HC11. In this configuration with SYNC low, the shift register clocks data out upon the rising edges of SCLK. Rev. H | Page 23 of 28 04587-105 SPIxSEL AD5450/AD5451/ AD5452/AD5453* 8051* AD5450/AD5451/ AD5452/AD5453* ADSP-BF5xx* To load data correctly to the DAC, P1.1 is left low after the first eight bits are transmitted, and a second write cycle is initiated to transmit the second byte of data. Data on RxD is clocked out of the microcontroller upon the rising edge of TxD and is valid upon the falling edge. As a result, no glue logic is required between the DAC and microcontroller interface. P1.1 is taken high following the completion of this cycle. The 80C51/80L51 provide the LSB of its SBUF register as the first bit in the data stream. The DAC input register acquires its data with the MSB as the first bit received. The transmit routine should take this into account. 04587-104 ADSP-BF504 to ADSP-BF592 Device Family to AD5450/AD5451/AD5452/AD5453 Interface AD5450/AD5451/AD5452/AD5453 Data Sheet MICROWIRE to AD5450/AD5451/AD5452/AD5453 Interface PCB LAYOUT AND POWER SUPPLY DECOUPLING In any circuit where accuracy is important, careful consideration of the power supply and ground return layout helps to ensure the rated performance. The PCB on which a AD5450/AD5451/ AD5452/AD5453 DAC is mounted should be designed so the analog and digital sections are separated and confined to certain areas of the board. If the DAC is in a system where multiple devices require an AGND to DGND connection, the connection should be made at one point only. The star ground point should be established as close as possible to the device. Figure 61 shows an interface between the DAC and any MICROWIRE-compatible device. Serial data is shifted out upon the falling edge of the serial clock, SK, and is clocked into the DAC input shift register upon the rising edge of SK, which corresponds to the falling edge of the DAC's SCLK. SK SCLK SO SDIN CS SYNC 04587-106 AD5450/AD5451/ AD5452/AD5453* MICROWIRE* *ADDITIONAL PINS OMITTED FOR CLARITY Figure 61. MICROWIRE to AD5450/AD5451/AD5452/AD5453 Interface PIC16C6x/PIC16C7x to AD5450/AD5451/AD5452/ AD5453 Interface The PIC16C6x/PIC16C7x (Microchip) synchronous serial port (SSP) is configured as an SPI master with the clock polarity bit (CKP) = 0. This is done by writing to the synchronous serial port control register (SSPCON). In this example, input/output Port RA1 is used to provide a SYNC signal and enable the serial port of the DAC. This microcontroller transfers only eight bits of data during each serial transfer operation; therefore, two consecutive write operations are required. Figure 62 shows the connection diagram. AD5450/AD5451/ AD5452/AD5453* SCK/RC3 SCLK SDI/RC4 SDIN RA1 *ADDITIONAL PINS OMITTED FOR CLARITY SYNC 04587-107 PIC16C6x/PIC16C7x* Figure 62. PIC16C6x/PIC16C7x to AD5450/AD5451/AD5452/AD5453 Interface These DACs should have ample supply bypassing of 10 F in parallel with 0.1 F on the supply located as close to the package as possible, ideally right up against the device. The 0.1 F capacitor should have low effective series resistance (ESR) and low effective series inductance (ESI), like the common ceramic types that provide a low impedance path to ground at high frequencies, to handle transient currents due to internal logic switching. Low ESR 1 F to 10 F tantalum or electrolytic capacitors should also be applied at the supplies to minimize transient disturbance and filter out low frequency ripple. Components, such as clocks, that produce fast switching signals should be shielded with a digital ground to avoid radiating noise to other devices of the board and should never be run near the reference inputs. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This reduces the effects of feedthrough through the board. A microstrip technique is the best solution, but its use is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to the ground plane and signal traces are placed on the solder side. It is good practice to employ compact, minimum lead length PCB layout design. Leads to the input should be as short as possible to minimize IR drops and stray inductance. The PCB metal traces between VREF and RFB should also be matched to minimize gain error. To optimize high frequency performance, the I-to-V amplifier should be located as close to the device as possible. Rev. H | Page 24 of 28 Data Sheet AD5450/AD5451/AD5452/AD5453 Table 13. Overview of the AD5405 to AD5453 Device Family and the AD5543 to AD5557 Device Family Part No. AD5424 AD5426 AD5428 AD5429 AD5450 AD5432 AD5433 AD5439 AD5440 AD5451 AD5443 AD5444 AD5415 AD5405 AD5445 AD5447 AD5449 AD5452 AD5446 AD5453 AD5553 AD5556 AD5555 AD5557 AD5543 AD5546 AD5545 AD5547 1 Resolution 8 8 8 8 8 10 10 10 10 10 12 12 12 12 12 12 12 12 14 14 14 14 14 14 16 16 16 16 No. DACs 1 1 2 2 1 1 1 2 2 1 1 1 2 2 2 2 2 1 1 1 1 1 2 2 1 1 2 2 INL (LSB) 0.25 0.25 0.25 0.25 0.25 0.5 0.5 0.5 0.5 0.25 1 0.5 1 1 1 1 1 0.5 1 2 1 1 1 1 2 2 2 2 Interface Parallel Serial Parallel Serial Serial Serial Parallel Serial Parallel Serial Serial Serial Serial Parallel Parallel Parallel Serial Serial Serial Serial Serial Parallel Serial Parallel Serial Parallel Serial Parallel Package 1 RU-16, CP-20 RM-10 RU-20 RU-10 UJ-8 RM-10 RU-20, CP-20 RU-16 RU-24 UJ-8 RM-10 RM-10 RU-24 CP-40 RU-20, CP-20 RU-24 RU-16 UJ-8, RM-8 RM-10 UJ-8, RM-8 RM-8 RU-28 RM-8 RU-38 RM-8 RU-28 RU-16 RU-38 RU = TSSOP, CP = LFCSP, RM = MSOP, UJ = TSOT. Rev. H | Page 25 of 28 Features 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 50 MHz serial 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 50 MHz serial 12 MHZ BW, 50 MHz serial interface 10 MHz BW, 50 MHz serial 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 50 MHz serial 10 MHz BW, 17 ns CS pulse width 12 MHz BW, 50 MHz serial interface 10 MHz BW, 50 MHz serial 12 MHz BW, 50 MHz serial 10 MHz BW, 50 MHz serial 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 50 MHz serial 12 MHz BW, 50 MHz serial interface 12 MHz BW, 50 MHz serial 12 MHz BW, 50 MHz serial 4 MHz BW, 50 MHz serial clock 4 MHz BW, 20 ns WR pulse width 4 MHz BW, 50 MHz serial clock 4 MHz BW, 20 ns WR pulse width 4 MHz BW, 50 MHz serial clock 4 MHz BW, 20 n WR pulse width 4 MHz BW, 50 MHz serial clock 4 MHz BW, 20 ns WR pulse width AD5450/AD5451/AD5452/AD5453 Data Sheet OUTLINE DIMENSIONS 2.90 BSC 8 7 6 5 1 2 3 4 2.80 BSC 1.60 BSC PIN 1 INDICATOR 0.65 BSC 1.95 BSC *0.90 0.87 0.84 *1.00 MAX 0.10 MAX 0.38 0.22 0.20 0.08 0.60 0.45 0.30 8 4 0 SEATING PLANE *COMPLIANT TO JEDEC STANDARDS MO-193-BA WITH THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS. Figure 63. 8-Lead Thin Small Outline Transistor Package [TSOT] (UJ-8) Dimensions shown in millimeters 3.20 3.00 2.80 8 3.20 3.00 2.80 1 5.15 4.90 4.65 5 4 PIN 1 IDENTIFIER 0.65 BSC 0.95 0.85 0.75 15 MAX 1.10 MAX 0.40 0.25 6 0 0.23 0.09 COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure 64. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters Rev. H | Page 26 of 28 0.80 0.55 0.40 10-07-2009-B 0.15 0.05 COPLANARITY 0.10 Data Sheet AD5450/AD5451/AD5452/AD5453 0.35 0.30 0.25 0.65 BSC 8 5 PIN 1 INDEX AREA 1.74 1.64 1.49 EXPOSED PAD 0.50 0.40 0.30 0.80 MAX 0.55 NOM 0.80 0.75 0.70 SEATING PLANE 1 4 BOTTOM VIEW TOP VIEW 0.05 MAX 0.02 NOM 0.20 REF 2.48 2.38 2.23 0.20 MIN PIN 1 INDICATOR (R 0.2) FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 02-05-2013-C 3.10 3.00 SQ 2.90 Figure 65. 8-Lead Lead Frame Chip Scale Package [LFCSP] 3 mm x 3 mm Body and 0.75 mm Package Height, Dual Lead (CP-8-3) Dimensions shown in millimeters ORDERING GUIDE Model 1, 2 AD5450YUJZ-REEL7 AD5451YUJZ-REEL7 AD5452YUJZ-REEL7 AD5452YRM AD5452YRM-REEL AD5452YRMZ AD5452YRMZ-REEL AD5452YRMZ-REEL7 AD5453WBCPZ-RL AD5453YUJZ-REEL7 AD5453YRM AD5453YRM-REEL AD5453YRM-REEL7 AD5453YRMZ AD5453YRMZ-REEL AD5453YRMZ-REEL7 1 2 Resolution 8 10 12 12 12 12 12 12 14 14 14 14 14 14 14 14 INL 0.25 0.25 0.5 0.5 0.5 0.5 0.5 0.5 2 2 2 2 2 2 2 2 Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C Package Description 8-Lead TSOT 8-Lead TSOT 8-Lead TSOT 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead LFCSP 8-Lead TSOT 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP Package Option UJ-8 UJ-8 UJ-8 RM-8 RM-8 RM-8 RM-8 RM-8 CP-8-3 UJ-8 RM-8 RM-8 RM-8 RM-8 RM-8 RM-8 Branding D6Y D6Z D70 D1Z D1Z D70 D70 D70 DG3 DAH D26 D26 D26 DAH DAH DAH Z = RoHS Compliant Part. W = Qualified for Automotive Applications. AUTOMOTIVE PRODUCTS The AD5453WBCPZ-RL model is available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that this automotive model may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. Rev. H | Page 27 of 28 AD5450/AD5451/AD5452/AD5453 Data Sheet NOTES (c)2005-2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04587-0-11/15(H) Rev. H | Page 28 of 28