Users should evaluate the suitability of this product for their application. Specications are subject to change without notice.
Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specication, without notication to Buyer.
1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER,
AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND
SUFFIXES MAY BE ADDED TO THE PART NUMBER AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER.
Page 1 of 1
The TE logo, TE Connectivity and Raychem are trademarks. Raychem Wire & Cable
501 Oakside Avenue
Redwood City, CA 94063-3800
Phone: 1-800-227-8816
Fax: 1-650-361-6297
DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL.
THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.
REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID.
© 2011 Tyco Electronics Corporation. All rights reserved.
JACKET - RADIATION-CROSSLINKED,
MODIFIED PVDF
COMPONENT WIRE - 44A011X
SHIELD - COPPER, COATING SAME AS ON
CONDUCTOR EXCEPT TIN-COATED
SHIELD WITH SILVER-COATED
HIGH-STRENGTH ALLOY CONDUCTOR
NOTE: Nominal values are for information only.
Nominal values are not requirements.
TABLE I. CABLE CONSTRUCTION DETAILS
PART NUMBER
1/
CONDUCTOR
SIZE
(AWG)
SHIELD
SIZE
(AWG)
JACKET THICKNESS
(in.)
OUTSIDE DIAMETER
(in.) MAXIMUM
WEIGHT
(lbs/1000 ft.)
MINIMUM NOMINAL NOMINAL MAXIMUM
44A111X-26-* 26 38 .005 .007 .065 .070 4.6
44A111X-24-* 24 38 .005 .007 .072 .077 5.8
44A111X-22-* 22 38 .005 .007 .079 .084 7.2
44A111X-20-* 20 38 .006 .008 .089 .094 9.9
44A111X-18-* 18 36 .006 .008 .103 .108 13.9
44A111X-16-* 16 36 .006 .008 .110 .115 16.5
44A111X-14-* 14 36 .006 .008 .127 .132 22.9
44A111X-12-* 12 36 .006 .008 .146 .151 32.1
44A111X-10-* 10 36 .006 .008 .166 .179 44.3
SPECIFICATION CONTROL DRAWING 44A111X
ONE CONDUCTOR CABLE, SHIELDED, JACKETED, GENERAL PURPOSE, 600 VOLT 4-1-11 G
This specication sheet forms a part of the latest issue of Raychem Specication 44.
TITLE Date Revision
TABLE II. CABLE PERFORMANCE DETAILS
PART NUMBER
1/
BEND TESTING
MANDREL DIAMETER
(inch) (±3%)
WEIGHT
(lb) (±3%)
LIFE CYCLE, IMMERSION
AND ACCELERATED AGING COLD
BEND
LIFE CYCLE, IMMERSION
AND ACCELERATED AGING COLD
BEND
44A111X-26-* 3.00 3.00 .125 .750
44A111X-24-* 3.00 3.00 .188 .750
44A111X-22-* 3.00 3.00 .188 1.50
44A111X-20-* 3.00 3.00 .188 1.50
44A111X-18-* 3.00 3.00 .250 1.50
44A111X-16-* 3.00 3.00 .250 1.50
44A111X-14-* 6.00 6.00 .500 4.50
44A111X-12-* 6.00 6.00 .500 4.50
44A111X-10-* 6.00 6.00 .500 4.50
SPECIFICATION CONTROL DRAWING Page 2 of 2 G44A111X
Revision SCD
TEMPERATURE RATING: 150°C
Maximum continuous conductor temperature
VOLTAGE RATING: 600 volts (rms) at sea level
ACCELERATED AGING: 300 ± 3°C for 6 hours
BLOCKING: 150 ± 3°C for 6 hours
DIELECTRIC WITHSTAND: 2500 volts (rms), 60 Hz, 1 minute
FLAMMABILITY: 30 seconds (maximum); 3 in. (maximum); no aming of facial tissue
IMMERSION: Diameter increase 5% (maximum), no cracking, no dielectric breakdown
JACKET COLOR: White preferred
JACKET CONCENTRICITY: 70% (minimum)
JACKET ELONGATION AND TENSILE STRENGTH:
Elongation, 200% (minimum)
Tensile Strength, 4000 lbf/in² (minimum)
JACKET FLAWS:
Spark Test, 1.5 kV (rms)
Impulse Dielectric Test, 6.0 kV (peak)
LIFE CYCLE: 200 ± 3°C for 168 hours
LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours
SHIELD COVERAGE: 85% (minimum)
VOLTAGE WITHSTAND (Post Environmental): 1000 volts (rms), 60 Hz, 1 minute
PART NUMBER:
The "X" in the part numbers on page 1 shall be replaced by the applicable conductor material
designator as follows:
1 tin-coated copper
2 silver-coated copper
3 nickel-coated copper
4 silver-coated high-strength copper alloy (AWG's 26 - 16 only)
6 nickel-coated high-strength copper alloy (AWG's 26 - 20 only)
The "*" in the part numbers on page 1 shall be replaced by color code designators with a dash
separating the component wire color from the jacket color.
1/ Example: AWG 20, tin-coated copper wire, white component wire; white jacket:
44A1111-20-9-9
1/ See footer section on page 1
CABLE RATINGS AND ADDITIONAL REQUIREMENTS
