1
155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM LUMNDS591-Apr2007
Rev A.2
Features
• Diplexer Single Mode Single Fiber 1x9 SC/FC/ST Receptacle
Connector
• Wavelength Tx 1310 nm/Rx 1530 nm
• SONET OC-3 SDH STM-1 Compliant
• Single +5V/+3.3V Power Supply
• PECL/LVPECL Differential Inputs and Output
[B-13/15-155-T(3)-Sxx3(4)]
• TTL/LVTTL Differential Inputs and Output
[B-13/15-155C-T(3)-Sxx3(4)]
• Wave Solderable and Aqueous Washable
• LED Multisourced 1x9 Transceiver Interchangeable
• Class 1 Laser Int. Safety Standard IEC 825 Compliant
• Uncooled Laser diode with MQW structure
• Complies with Telcordia (Bellcore) GR-468-CORE
• RoHS compliance available
Parameter Symbol Min. Max. Unit Note
Power Supply Voltage Vcc 0 6 V B-13/15-155(C)-T-Sxx3(4)
Power Supply Voltage Vcc 0 3.6 V B-13/15-155(C)-T3-Sxx3(4)
Input Voltage -0 Vcc V
Output Current Iout - 30 mA
Soldering Temperature -- 260 ºC 10 seconds on leads only
Storage Temperature Tstg -40 85 ºC
Absolute Maximum Rating
Parameter Symbol Min. Typ. Max. Unit
Power Supply Voltage Vcc 4.75 5 5.25 V
Power Supply Voltage Vcc 3.1 3.3 3.5 V
Operating Temperature (Case) Topr 0 - 70 ºC
Operating Temperature (Case) Topr -40 - 85 ºC
Data Rate - - 155 - Mbps
Recommended Operating Condition
Parameter Symbol Min Typical Max Unit Notes
Optical
Optical Transmit Power Po-14 - -8 dBm Output power is coupled into a 9/125 µm
single mode fiber.B-13/15-155(C)-T(3)-Sxx3
Optical Transmit Power Po-8 - -3 dBm Output power is coupled into a 9/125 µm
single mode fiber.B-13/15-155(C)-T(3)-Sxx4
Output center Wavelength λ1260 1310 1360 nm
Output Spectrum Width ∆λ - - 3 nm RMS (σ)
Extinction Ratio ER 8.2 - - dB
Output Eye Compliant with ITU-T recommendation G.957/STM-1
Optical Rise Time Tr - - 2 ns 10% to 90% Values
Optical Fall Time Tf - - 2 ns 10% to 90% Values
Optical Isolation -30 - - dB Tx:1530 nm/ Rx:1310 nm
Relative Intensity Noise RIN - - -116 dB/Hz
Total Jitter TJ - - 1.2 ns Measured with 223-1 PRBS with 72 ones and
72 zeros.
Transmitter Specifications
2
155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM LUMNDS591-Apr2007
Rev A.2
Parameter Symbol Min Typical Max Unit Notes
Electrical
Power Supply Current ICC - - 140 mA Maximum current is specified at Vcc=
Maximum @ maximum temperature
Data Input Current-Low IIL -350 - - µA
Data Input Current-High IIH - - 350 µA
Differential Input Voltage VIH-VIL 300 - - mV
Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V These inputs are compatible with 10K,
10KH and 100K ECL and PECL inputs
Data Input Voltage-High VIH-VCC -1.1 - -0.74 V
Transmitter Specifications
Parameter Symbol Min Typical Max Unit Notes
Optical
Sensitivity - - - -33 dBm Measured with 223-1 PRBS, BER = 10-10
Maximum Input Power Pin -3 - - dBm
Signal Detect-Asserted Pa - - -33 dBm Measured on transition: low to high
(Note1)
Signal Detect-Deasserted Pd -45 - - dBm
Signal Detect-Hysteresis 1.0 - 4.0 dB
Cross Talk - - - -33 dB
Wavelength of Operation 1480 - 1600 nm
Note 1: The SD level should be deasserted when fiber disconnected
Receiver Specifications
Parameter Symbol Min Typical Max Unit Note
Electrical
Power Supply Current ICC - - 100 mA The current excludes the output load
current
Data output Voltage-Low VOL -Vcc -2.0 - -1.58 V These outputs are compatible with 10K,
10KH and 100KECL and PECL outputs
Data output Voltage-High VOH- Vcc -1.1 - -0.74 V
Signal Detect output Voltge-Low VSDL-Vcc -2.0 - -1.58 V B-13/15-155-T(3)-Sxx3(4)
Signal Detect Output Voltge-High VSDH- Vcc -1.1 - -0.74 V
Signal Detect Output Voltage-Low VSDL - - 0.5 V B-13/15-155C-T(3)-Sxx3(4)
Signal Detect Output Voltage-High VSDH 2.0 - - V
Receiver Specifications
3
155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM LUMNDS591-Apr2007
Rev A.2
Warnings
Connection Diagram
1. (Rx GND)
2. (Rx +) NC
3. (Rx-)
4. (SD)
5. (Rx Vcc) Top View
6. (Tx Vcc)
7. (TX-) NC
8. (TX+)
9. (Tx GND)
Receiver Signal Ground
Receiver Data Out
Receiver Data Out Bar
Signal Detect
Receiver Power Supply
Transmitter Power Supply
Transmitter Data In Bar
Transmitter Data in
Transmitter Signal Ground
PIN Symbol Notes
1RxGND Directly connect this pin to the receiver ground plane
2 RD+ See recommended circuit schematic
3 RD- See recommended circuit schematic
4 SD Active high on this indicates a received optical signal
5 RxVcc DC power for the receiver section
6 TxVcc DC power for the transmitter section
7 TD- See recommended circuit schematic
8 TD+ See recommended circuit schematic
9 TxGND Directly connect this pin to the transmitter ground plane
4
155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM LUMNDS591-Apr2007
Rev A.2
Recommended Circuit Schematic (3.3V/5V)
123
45
97
8 6
Rx Vcc
Tx Vcc
Transceiver
Top view
No internal
connection
No internal
connection
C2
C1
C4
L2
C3
L1
Rx Vcc
Tx Vcc
Vcc
Tx Vcc Rx Vcc
RD +
RD -
SD
TD +
TD -
R8
R10
R9 R7
C6
C5 R1 R3
R2 R4
R5
R6
Notes +3.3V:
R1=R3=R5=R7=R9=130
R2=R4=R6=R8=R10=82
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
Notes +5V:
R1=R3=R5=R7=R9=82
R2=R4=R6=R8=R10=130
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc.
A GND plane under the module is required for good EMI and sensitivity performance.
Recommended Circuit Schematic (3.3V/5V)
123
45
97
8 6
Rx Vcc
Tx Vcc
Transceiver
Top view
No internal
connection
No internal
connection
C2
C1
C4
L2
C3
L1
Rx Vcc
Tx Vcc
Vcc
Tx Vcc Rx Vcc
RD +
RD -
SD
TD +
TD -
R6 R8
R7 C6
C5 R1 R3
R2 R4
R5
Notes +3.3V:
R1=R3=R5=R7=130
R2=R4=R6=R8=82
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
Notes +5V:
R1=R3=R5=R7=82
R2=R4=R6=R8=130
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
B-13/15-155-T(3)-Sxx3(4)
B-13/15-155C-T(3)-Sxx3(4)
5
155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM LUMNDS591-Apr2007
Rev A.2
Side View
Rear View
Top View
Front View
Package Diagram
B-13/15-155(C)-T(3)-SSC3(4)
6
155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM LUMNDS591-Apr2007
Rev A.2
Top View Front View
Top View Front View
Package Diagram
Package Diagram
B-13/15-155(C)-T(3)-SST3(4)
B-13/15-155(C)-T(3)-SFC3(4)
7
155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
LUMINENTOIC.COM LUMNDS591-Apr2007
Rev A.2
Ordering Information
B - 13/15 - 155(C) - T(3) - S XX Tx Power Temperature and Package -RoHS
• Wavelength
Tx Wavelength=1310nm
Rx Wavelength=1530nm
• Communication protocol
(155 Mbps)
155 = PECL Signal Detection Optupt
155C = TTL Signal Detection Optupt
• T = +5 V Transceiver
T3 = +3.3V Transceiver
Part Numbering Definitions:
Available Options:
B-13/15-155(C)-T-SSC3(4)(A)
B-13/15-155(C)-T-SFC3(4)(A)
B-13/15-155(C)-T-SST3(4)(A)
B-13/15-155(C)-T3-SSC3(4)(A)
B-13/15-155(C)-T3-SFC3(4)(A)
B-13/15-155(C)-T3-SST3(4)(A)
B-13/15-155(C)-T-SSC3(4)(A)-G5
B-13/15-155(C)-T-SFC3(4)(A)-G5
B-13/15-155(C)-T-SST3(4)(A)-G5
B-13/15-155(C)-T3-SSC3(4)(A)-G5
B-13/15-155(C)-T3-SFC3(4)(A)-G5
B-13/15-155(C)-T3-SST3(4)(A)-G5
B-13/15-155(C)-T-SSC3(4)(A)-GR
B-13/15-155(C)-T-SFC3(4)(A)-GR
B-13/15-155(C)-T-SST3(4)(A)-GR
B-13/15-155(C)-T3-SSC3(4)(A)-GR
B-13/15-155(C)-T3-SFC3(4)(A)-GR
B-13/15-155(C)-T3-SST3(4)(A)-GR
• Connector options
SC/ST/FC
• Tx Power
3 = -14 to -8 dBm
4 = -8 to -3 dBm
• RoHS
Blank = RoHS non-compliant product
G5 = RoHS 5/6-compliant product (lead exemption)
GR = Full RoHS compliant product (no exemption)
• Temperature range and package
Blank = commercial temperature(0 to 70 ºC)
A = industrial temperature(-40 to 85 ºC)
• Single mode fiber
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
8
155 Mbps Bi-directional Receptacle
Single Fiber Transceiver
B-13/15-155(C)-T(3)-Sxx3(4)
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warran-
ties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this docu-
ment are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 LUMNDS591-Apr2007
Rev A.2
Warnings
Legal Notice
