36 37
Soldering and Desoldering Tips
Nickel-plating
The base material made of highly conductive
electrolytic copper ensures unhindered heat
transfer from the heating element to the
ERSADUR LF coating
ERSADUR LF coating (up to 600
micron) of iron-plating (subject to
type of tip) is factory pre-tinned
with lead-free solder at working
end
Iron-plating
Chrome-plating prevents corrosion and
solder collection on undesirable spots
Nickel-plating
Cross-section of an ERSADUR soldering tip, non-scale representation
Important notice: special care for soldering tips!
Hand soldering operators are happy when their soldering tips last
a long time and continue to solder well. Soldering tips that do not
allow the solder to melt rapidly due to excess oxidation clearly
disrupt productivity! Special care of the soldering tip should be
taken in order to solder efficiently.
Important Facts:
1. When a soldering tip remains hot for a long period of time, the
tip will oxidize or blacken. An oxidized tip will no longer „wet“ or
melt solder properly.
2. The higher the working temperature of the soldering tip, the
faster this oxidation will take place and tip lifetime will be
shorter.
3. Soldering irons that automatically go into a lower “stand-by”
temperature increase tip life.
4. The oxidation of the tip will be very rapid if the tip is left “cook-
ing” without molten solder covering the tip end. It happens, for
example, if the tip is not wettned with solder right after cleaning
it.
5. Excessive mechanical force during soldering will shorten the tip
life.
6. Proper care of the tip will greatly increase tip life.
7. Lead-free soldering requires higher temperatures, is more ag-
gressive to the tip and will always lead to shorter tip life.
Special Care:
1. Always clean the tip by wiping on a slightly wet sponge after
each use. Alternatively, tips can be dry cleaned using wire
mesh.
2. Always put fresh solder onto the end of the tip BEFORE putting
the tip back into the iron holder.
3. Always use lowest working temperature possible.
4. Never leave an iron “cooking” unattended for some time.
Always set iron into automatic stand-by if possible or turn-off
when not in use.
5. Never use excessive mechanical force when soldering.
6. Soldering tip oxidation can be easily removed if detected early.
Early detection and removal will greatly increase tip life.
7. Tip oxidation removal or tip refurbishing is accomplished in 4
consecutive steps: a. clean on damp sponge, b. clean with wire
brush, c. using a Tip re-activator chemical, and d. re-tinning
using proper flux cored solder wire.
ERSADUR LF soldering tips to process lead-free solders
Conventional soldering tips can also be used for lead-free solders.
Since lead-free soldering requires higher process temperatures,
and due to the fact that lead-free solder is more aggressive to the
soldering tip, the tip’s service life is shorter. ERSADUR LF solder-
ing tips have an increased layer of iron, which increases tip life.
Consequently they are especially suitable for lead-free soldering.
The ERSA Tip-Reactivator al-
lows the regeneration of oxidized
soldering tips. It is environmen-
tally safe, free of lead and halo-
gens and func-tions even at low
soldering tip temperatures. For
this purpose the heated soldering
tip is wiped on the surface of the
regeneration compound.
38 39
Your Guide
For:
For:
722 Desoldering Tip Series, ERSADUR / nickel-plated
0722ED1023
ERSADUR, ID 1.0 mm, OD 2.3 mm
• DIGITAL 2000 A
with X-Tool desoldering
iron
• XTOOLKIT1
0722ED0821
ERSADUR, ID 0.8 mm, OD 2.1 mm
0722EN0818
nickel-plated, ID 0.8 mm, OD 1.8 mm
0722EN1020
nickel-plated, ID 1.0 mm, OD 2.0 mm
0722EN1023
nickel-plated, ID 1.0 mm,OD 2.3 mm
0722EN0823
nickel-plated, ID 0.8 mm, OD 2.3 mm
0722EN1223
nickel-plated, ID
1.2 mm, OD 2.3 mm
0722ED1226
ERSADUR, ID 1.2 mm, OD 2.6 mm
0722EN1529
nickel-plated, ID 1.5 mm, OD 2.9 mm
0722EN1548
nickel-plated, ID 1.5 mm, OD 4.8 mm
0722EN2332
nickel-plated, ID 2.3 mm, OD 3.2 mm
0722EN2348
nickel-plated, ID 2.3 mm, OD 4.8 mm
0722EN0615S
nickel-plated, ID 0.6 mm , OD 1.5 mm
0722EN1018S
nickel-plated, ID 1.0 mm , OD 1.8 mm
842 ERSADUR Long-Life Soldering Tip Series
• ANALOG 60 / 60 A
• ANALOG 80 / 80 A
• DIGITAL 80 A
• DIGITAL 2000 A
with Power tool soldering
iron
• ELS 8000 / M / D
• MICRO-CON 60 iA
with Power tool soldering
iron
• MS 6000
• MS 8000 / D
• Multi-Pro
• Multi-Sprint
• Multi-TC
• RDS 80
• TWIN 80 A
with Ergo tool soldering
iron
0842UD / UDLF
pencil point, extenced, 0.4 mm ø
0842SD / SDLF
pencil point, extenced, 0.8 mm ø
0842BD / BDLF
pencil point, 1.0 mm ø
0842YD / YDLF
chisel-shaped, 1.6 mm
0842CD / CDLF
chisel-shaped, 2.2 mm
0842KD / KDLF
chisel-shaped, extended, 2.2 mm
0842JD0842ID0842ED / EDLF
chisel-shaped, bent, 2.2 mmpencil point, bent, 0.4 mm øchisel-shaped, 3.2 mm
0722ED1529
ERSADUR,
ID 1.5 mm, OD 2.9 mm
