Philips Semiconductors Product specification
Three quadrant triacs BTA208 series D, E and F
guaranteed commutation
GENERAL DESCRIPTION QUICK REFERENCE DATA
Passivated guaranteed commutation SYMBOL PARAMETER MAX. MAX. UNIT
triacs in a plastic envelope intended for
use in motor control circuits or with other BTA208- 600D -
highly inductive loads. These devices BTA208- 600E 800E
balancetherequirementsofcommutation BTA208- 600F 800F
performance and gate sensitivity. The VDRM Repetitive peak 600 800 V
"sensitive gate" E series and "logic level" off-state voltages
D series are intended for interfacing with IT(RMS) RMS on-state current 8 8 A
low power drivers, including micro ITSM Non-repetitive peak on-state 65 65 A
controllers. current
PINNING - TO220AB PIN CONFIGURATION SYMBOL
PIN DESCRIPTION
1 main terminal 1
2 main terminal 2
3 gate
tab main terminal 2
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum System (IEC 134).
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
-600 -800
VDRM Repetitive peak off-state - 6001800 V
voltages
IT(RMS) RMS on-state current full sine wave; - 8 A
Tmb ≤ 102 ˚C
ITSM Non-repetitive peak full sine wave;
on-state current Tj = 25 ˚C prior to
surge
t = 20 ms - 65 A
t = 16.7 ms - 72 A
I2tI
2t for fusing t = 10 ms - 21 A2s
dIT/dt Repetitive rate of rise of ITM = 12 A; IG = 0.2 A; 100 A/µs
on-state current after dIG/dt = 0.2 A/µs
triggering
IGM Peak gate current - 2 A
VGM Peak gate voltage - 5 V
PGM Peak gate power - 5 W
PG(AV) Average gate power over any 20 ms - 0.5 W
period
Tstg Storage temperature -40 150 ˚C
TjOperating junction - 125 ˚C
temperature
T1T2
G
123
tab
1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may
switch to the on-state. The rate of rise of current should not exceed 6 A/µs.
February 2000 1 Rev 1.000
Philips Semiconductors Product specification
Three quadrant triacs BTA208 series D, E and F
guaranteed commutation
THERMAL RESISTANCES
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Rth j-mb Thermal resistance full cycle - - 2.0 K/W
junction to mounting base half cycle - - 2.4 K/W
Rth j-a Thermal resistance in free air - 60 - K/W
junction to ambient
STATIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
BTA208- ...D ...D ...E ...F
IGT Gate trigger current2VD = 12 V; IT = 0.1 A
T2+ G+ - 0.8 5 10 25 mA
T2+ G- - 2.0 5 10 25 mA
T2- G- - 3.2 5 10 25 mA
ILLatching current VD = 12 V; IGT = 0.1 A
T2+ G+ - 7.2 15 25 30 mA
T2+ G- - 8.2 25 30 40 mA
T2- G- - 11.0 25 30 40 mA
IHHolding current VD = 12 V; IGT = 0.1 A - 5.3 15 25 30 mA
...D, E, F
VTOn-state voltage IT = 10 A - 1.3 1.65 V
VGT Gate trigger voltage VD = 12 V; IT = 0.1 A - 0.7 1.5 V
VD = 400 V; IT = 0.1 A; 0.25 0.4 - V
Tj = 125 ˚C
IDOff-state leakage current VD = VDRM(max); - 0.1 0.5 mA
Tj = 125 ˚C
DYNAMIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
BTA208- ...D ...E ...F ...D
dVD/dt Critical rate of rise of VDM = 67% VDRM(max); 20607060 -V/µs
off-state voltage Tj = 110 ˚C; exponential
waveform; gate open
circuit
dIcom/dt Critical rate of change of VDM = 400 V; Tj = 110 ˚C; 1.8 3.5 5 8.5 - A/ms
commutating current IT(RMS) = 8 A;
dVcom/dt = 20V/µs; gate
open circuit
dIcom/dt Critical rate of change of VDM = 400 V; Tj = 110 ˚C; 5 16 19 100
commutating current IT(RMS) = 8 A; - A/ms
dVcom/dt = 0.1V/µs; gate
open circuit ...D, E, F
tgt Gate controlled turn-on ITM = 12 A; VD = VDRM(max);- - - 2 - µs
time IG = 0.1 A; dIG/dt = 5 A/µs
2 Device does not trigger in the T2-, G+ quadrant.
February 2000 2 Rev 1.000
Philips Semiconductors Product specification
Three quadrant triacs BTA208 series D, E and F
guaranteed commutation
Fig.1. Maximum on-state dissipation, Ptot, versus rms
on-state current, IT(RMS), where α = conduction angle.
Fig.2. Maximum permissible non-repetitive peak
on-state current ITSM, versus pulse width tp, for
sinusoidal currents, tp ≤ 20ms.
Fig.3. Maximum permissible non-repetitive peak
on-state current ITSM, versus number of cycles, for
sinusoidal currents, f = 50 Hz.
Fig.4. Maximum permissible rms current IT(RMS) ,
versus mounting base temperature Tmb.
Fig.5. Maximum permissible repetitive rms on-state
current IT(RMS), versus surge duration, for sinusoidal
currents, f = 50 Hz; Tmb ≤ 102˚C.
Fig.6. Normalised gate trigger voltage
VGT(Tj)/ VGT(25˚C), versus junction temperature Tj.
0246810
0
2
4
6
8
10
12 = 180
120
90
60
30
IT(RMS) / A
Ptot / W Tmb(max) / C
125
121
117
113
109
105
101
1
-50 0 50 100 150
0
2
4
6
8
10 BT137
102 C
Tmb / C
IT(RMS) / A
10us 100us 1ms 10ms 100ms
10
100
1000
T / s
ITSM / A
dI /dt limit
T
TITSM
time
I
Tj initial = 25 C max
T
0.01 0.1 1 10
0
5
10
15
20
25
surge duration / s
IT(RMS) / A
1 10 100 1000
0
10
20
30
40
50
60
70
Number of half cycles at 50Hz
ITSM / A
TITSM
time
I
T
Tj initial = 25 C max
-50 0 50 100 150
0.4
0.6
0.8
1
1.2
1.4
1.6
Tj / C
VGT(Tj)
VGT(25 C)
February 2000 3 Rev 1.000
Philips Semiconductors Product specification
Three quadrant triacs BTA208 series D, E and F
guaranteed commutation
Fig.7. Normalised gate trigger current
IGT(Tj)/ IGT(25˚C), versus junction temperature Tj.
Fig.8. Normalised latching current IL(Tj)/ IL(25˚C),
versus junction temperature Tj.
Fig.9. Normalised holding current IH(Tj)/ IH(25˚C),
versus junction temperature Tj.
Fig.10. Typical and maximum on-state characteristic.
Fig.11. Transient thermal impedance Zth j-mb, versus
pulse width tp.
Fig.12. Minimum, critical rate of change of
commutating current, dIcom/dt versus junction
temperature, dVcom/dt = 20V/µs.
0
0.5
1
1.5
2
2.5
3
-50 0 50 100 150
T2+ G+
T2+ G-
T2- G-
Tj/°C
IGT(Tj)
IGT(25°C)
0 0.5 1 1.5 2 2.5 3
0
5
10
15
20
25
VT / V
IT / A
Tj = 125 C
Tj = 25 C typ max
Vo = 1.264 V
Rs = 0.0378 Ohms
-50 0 50 100 150
0
0.5
1
1.5
2
2.5
3
Tj / C
IL(Tj)
IL(25 C)
10us 0.1ms 1ms 10ms 0.1s 1s 10s
0.01
0.1
1
10
tp / s
Zth j-mb (K/W)
tp
P
t
D
bidirectional
unidirectional
-50 0 50 100 150
0
0.5
1
1.5
2
2.5
3
Tj / C
IH(Tj)
IH(25C)
1
10
100
20 40 60 80 100 120 140
F TYPE
E TYPE
D TYPE
Tj/˚C
dIcom/dt (A/ms)
February 2000 4 Rev 1.000
Philips Semiconductors Product specification
Three quadrant triacs BTA208 series D, E and F
guaranteed commutation
MECHANICAL DATA
Dimensions in mm
Net Mass: 2 g
Fig.13. SOT78 (TO220AB). pin 2 connected to mounting base.
Notes
1. Refer to mounting instructions for SOT78 (TO220) envelopes.
2. Epoxy meets UL94 V0 at 1/8".
10,3
max
3,7
2,8
3,0
3,0 max
not tinned
1,3
max
(2x) 123
2,4
0,6
4,5
max
5,9
min
15,8
max
1,3
2,54 2,54
0,9 max (3x)
13,5
min
February 2000 5 Rev 1.000
Philips Semiconductors Product specification
Three quadrant triacs BTA208 series D, E and F
guaranteed commutation
DEFINITIONS
Data sheet status
Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.
Limiting values
Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and
operation of the device at these or at any other conditions above those given in the Characteristics sections of
this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
Philips Electronics N.V. 2000
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the
copyright owner.
The information presented in this document does not form part of any quotation or contract, it is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under patent or other
industrial or intellectual property rights.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices or systems where malfunction of these
products can be reasonably expected to result in personal injury. Philips customers using or selling these products
for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting
from such improper use or sale.
February 2000 6 Rev 1.000
