Bulletin PD-20826 09/04 10CTQ150PbF 10 Amp SCHOTTKY RECTIFIER IF(AV) = 10 Amp VR = 150V Description/ Features Major Ratings and Characteristics Characteristics Values Units IF(AV) Rectangular 10 A VRRM 150 V IFSM @ tp = 5 s sine 620 A VF @ 5 Apk, TJ = 125C 0.73 V TJ range - 55 to 175 C waveform This center tap Schottky ectifier has been optimized for low reverse leakage at high temperature. The proprietary barrier technology allows for reliable operation up to 175 C junction temperature. Typical applications are in switching power supplies, converters, free-wheeling diodes, and reverse battery protection. 175 C TJ operation Center tap configuration Low forward voltage drop (per leg) High purity, high temperature epoxy encapsulation for enhanced mechanical strength and moisture resistance High frequency operation Guard ring for enhanced ruggedness and long term reliability Lead-Free ("PbF" suffix) Case Styles 10CTQ150PbF Base Common Cathode 2 1 Anode 2 Common Cathode 3 Anode TO-220 www.irf.com 1 10CTQ150PbF Bulletin PD-20826 09/04 Voltage Ratings Parameters VR 10CTQ150PbF Max. DC Reverse Voltage (V) 150 VRWM Max. Working Peak Reverse Voltage (V) Absolute Maximum Ratings Parameters IF(AV) Max. Average Forward Current IFSM EAS IAR * See Fig. 5 Values Units 5 A 50% duty cycle @ TC = 155C, rectangular wave form A 5s Sine or 3s Rect. pulse Following any rated load condition and with 10ms Sine or 6ms Rect. pulse rated V RRM applied (Per Leg) (Per Device) Conditions 10 Max. Peak One Cycle Non-Repetitive 620 Surge Current (Per Leg) 115 * See Fig. 7 Non-Repetitive Avalanche Energy (Per Leg) 6.75 mJ Repetitive Avalanche Current 0.30 A (Per Leg) TJ = 25 C, IAS = 0.30 Amps, L = 150 mH Current decaying linearly to zero in 1 sec Frequency limited by TJ max. VA = 1.5 x VR typical Electrical Specifications Parameters VFM IRM Values Units 0.93 1.10 0.73 V V V @ 5A @ 10A @ 5A 0.86 V @ 10A Max. Forward Voltage Drop (Per Leg) * See Fig. 1 (1) Max. Reverse Leakage Current (Per Leg) * See Fig. 2 (1) VF(TO) Threshold Voltage Conditions TJ = 25 C TJ = 125 C 0.05 mA TJ = 25 C 7 mA TJ = 125 C TJ = TJ max. VR = rated VR 0.468 V rt Forward Slope Resistance 28 m CT Max. Junction Capacitance (Per Leg) 200 pF VR = 5VDC (test signal range 100Khz to 1Mhz) 25C LS Typical Series Inductance (Per Leg) 8.0 nH Measured lead to lead 5mm from package body dv/dt Max. Voltage Rate of Change 10000 V/ s (Rated VR) (1) Pulse Width < 300s, Duty Cycle <2% Thermal-Mechanical Specifications Parameters Values Units TJ Max. Junction Temperature Range -55 to 175 C Tstg Max. Storage Temperature Range -55 to 175 Conditions C RthJC Max. Thermal Resistance Junction to Case (Per Leg) 3.50 C/W DC operation RthJC Max. Thermal Resistance Junction to Case (Per Package) 1.75 C/W DC operation RthCS Typical Thermal Resistance, Case to Heatsink (only for TO-220) 0.50 C/W Mounting surface , smooth and greased wt Approximate Weight T Mounting Torque Marking Device 2 2 (0.07) g (oz.) Min. 6 (5) Max. 12 (10) Kg-cm (Ibf-in) 10CTQ150 www.irf.com 10CTQ150PbF Bulletin PD-20826 09/04 100 100 TJ = 175C (mA) 10 150C Reverse Current - I 125C 0.1 100C 75C 0.01 50C 0.001 TJ = 175C 0.0001 TJ = 125C 10 25C 0 25 50 75 100 125 150 Reverse Voltage - V R (V) TJ = 25C Fig. 2 - Typical Values Of Reverse Current Vs. Reverse Voltage (Per Leg) (pF) 1000 Junction Capacitance - C T Instantaneous Forward Current - I F (A) R 1 1 0 0.5 1 1.5 2 2.5 T = 25C J 100 10 3 0 20 40 60 80 100 120 140 160 Reverse Voltage - VR (V) Forward Voltage Drop - V FM (V) Fig. 3 - Typical Junction Capacitance Vs. Reverse Voltage (Per Leg) Fig. 1 - Max. Forward Voltage Drop Characteristics (Per Leg) Thermal Impeda nc e Z thJC (C/W) 10 1 D = 0.75 D = 0.50 D = 0.33 0.1 D = 0.25 D = 0.20 PDM t1 0.01 0.001 0.00001 Single Pulse (Thermal Resistance) 0.0001 0.001 0.01 Notes: t2 1. Duty factor D = t 1/ t 2 2. Peak TJ = PDM x Z thJC+ TC 0.1 1 10 100 t 1 , Rectangular Pulse Duration (Seconds) Fig. 4 - Max. Thermal Impedance ZthJC Characteristics (Per Leg) www.irf.com 3 10CTQ150PbF Bulletin PD-20826 09/04 5 170 Average Power Loss - (Watts) Allowable Case Temperature - (C) 180 DC 160 150 Square wave (D = 0.50) 80% Rated V R applied 140 130 D = 0.20 D = 0.25 D = 0.33 D = 0.50 D = 0.75 4 DC 3 RMSLimit 2 1 see note (2) 120 0 2 4 6 0 8 0 Average Forward Current - I F(AV) (A) 1 2 3 4 5 6 7 8 Average Forward Current - I F(AV) (A) Fig. 5 - Max. Allowable Case Temperature Vs. Average Forward Current (Per Leg) Fig. 6 - Forward Power Loss Characteristics (Per Leg) 1000 Non-Repetitive Surge Current - I FSM (A) At Any Rated Load Condition And With Rated VRRM Applied Following Surge 100 10 100 1000 10000 Square Wave Pulse Duration - t p (microsec) Fig. 7 - Max. Non-Repetitive Surge Current (Per Leg) L IRFP460 DUT Rg = 25 ohm CURRENT MONITOR HIGH-SPEED SWITCH FREE-WHEEL DIODE + Vd = 25 Volt 40HFL40S02 Fig. 8 - Unclamped Inductive Test Circuit (2) Formula used: TC = TJ - (Pd + PdREV) x RthJC ; Pd = Forward Power Loss = IF(AV) x VFM @ (IF(AV) / D) (see Fig. 6); PdREV = Inverse Power Loss = VR1 x IR (1 - D); IR @ VR1 = 10 V 4 www.irf.com 10CTQ150PbF Bulletin PD-20826 09/04 Outline Table 10.54 (0.41) MAX. 3.78 (0.15) 3.54 (0.14) 1.32 (0.05) 1.22 (0.05) DIA. 15.24 (0.60) 14.84 (0.58) Base Common Cathode 6.48 (0.25) 6.23 (0.24) 2.92 (0.11) 2.54 (0.10) TERM 2 2 2 1 2 3 14.09 (0.55) 3.96 (0.16) 13.47 (0.53) 3.55 (0.14) 0.10 (0.004) 1 Anode 2 Common Cathode 3 Anode 2.04 (0.080) MAX. 1.40 (0.05) 2.89 (0.11) 1.15 (0.04) 2.64 (0.10) 0.94 (0.04) 0.69 (0.03) 1 2 3 4.57 (0.18) 0.61 (0.02) MAX. 4.32 (0.17) Conform to JEDEC outline TO-220AB Dimensions in millimeters and (inches) 5.08 (0.20) REF. Part Marking Information IRXC Assembly Line EXAMPLE: THIS IS A 10CTQ150 LOT CODE 1789 ASSEMBLED ON WW 19, 2001 IN THE ASSEMBLY LINE "C" IRMX Assembly Line EXAMPLE: THIS IS A 10CTQ150 LOT CODE 1789 ASSEMBLED ON WW 19, 2001 www.irf.com INTERNATIONAL RECTIFIER LOGO ASSEMBLY LOT CODE INTERNATIONAL RECTIFIER LOGO ASSEMBLY LOT CODE PART NUMBER DATE CODE P = LEAD-FREE YEAR 1 = 2001 WEEK 19 LINE C PART NUMBER DATE CODE YEAR 1 = 2001 WEEK 19 P = LEAD-FREE 5 10CTQ150PbF Bulletin PD-20826 09/04 Ordering Information Table Device Code 10 C T Q 1 2 3 4 150 PbF 5 1 - Current Rating (10 = 10A) 2 - Circuit Configuration 6 C = Common Cathode 3 - Package 4 - Schottky "Q" Series 5 - Voltage Rating (150 = 150A) 6 - y none = Standard Production T = TO-220 y PbF = Lead-Free Tube Standard Pack Quantity : 50 pieces Data and specifications subject to change without notice. This product has been designed and qualified for Industrial Level and Lead-Free. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 09/04 6 www.irf.com