Precision Edge(R) SY89833L (R) 3.3V ULTRA-PRECISION 1:4 LVDS FANOUT BUFFER/TRANSLATOR WITH INTERNAL TERMINATION Micrel, Inc. Precision Edge SY89833L FEATURES Precision Edge(R) Guaranteed AC performance over temperature and voltage: * DC-to > 2GHz throughput * <600ps propagation delay (IN-to-Q) * <20ps within-device skew * <190ps rise/fall times Ultra-low jitter design * <1psRMS cycle-to-cycle jitter * <10psPP total jitter * <1psRMS random jitter * <10psPP deterministic jitter Unique input termination and VT pin accepts DCand AC-coupled inputs High-speed LVDS outputs 3.3V power supply operation Industrial temperature range: -40C to +85C Available in 16-pin (3mm x 3mm) MLF(R) package DESCRIPTION The SY89833L is a 3.3V, high-speed 2GHz differential Low Voltage Differential Swing (LVDS) 1:4 fanout buffer optimized for ultra-low skew applications. Within device skew is guaranteed to be less than 20ps over supply voltage and temperature. The differential input buffer has a unique internal termination design that allows access to the termination network through a VT pin. This feature allows the device to easily interface to different logic standards. A VREF-AC reference is included for AC-coupled applications. The SY89833L is part of Micrel's high-speed clock synchronization family. For 2.5V applications, the SY89832U provides similar functionality while operating from a 2.5V 5% supply. For applications that require a different I/O combination, consult the Micrel website at: www.micrel.com, and choose from a comprehensive product line of highspeed, low-skew fanout buffers, translators and clock generators. APPLICATIONS Processor clock distribution SONET clock distribution Fibre Channel clock distribution Gigabit Ethernet clock distribution FUNCTIONAL BLOCK DIAGRAM TYPICAL PERFORMANCE 1:4 622MHz Output Q0 /Q0 IN -15mV Offset (50mV/div.) Q1 /Q1 50 VT /IN 50 Q2 VREF-AC EN (LVTTL/CMOS) /Q2 D Q Q3 /Q3 TIME (321.9ps/div.) Precision Edge is a registered trademark of Micrel, Inc. MicroLeadFrame and MLF are registered trademarks of Amkor Technology, Inc. August 2007 1 M9999-082407 hbwhelp@micrel.com or (408) 955-1690 Precision Edge(R) SY89833L Micrel Inc. /Q0 Q0 VCC GND PACKAGE/ORDERING INFORMATION 16 15 14 13 Ordering Information(1) Q1 1 12 IN /Q1 2 11 VT 10 VREF-AC 4 /IN 5 6 7 8 VCC EN 9 Q3 /Q2 3 /Q3 Q2 Part Number Package Type Operating Range Package Marking Lead Finish SY89833LMI MLF-16 Industrial 833L Sn-Pb SY89833LMITR(2) MLF-16 Industrial 833L Sn-Pb SY89833LMG(3) MLF-16 Industrial 833L with Pb-Free bar line indicator NiPdAu Pb-Free SY89833LMGTR(2, 3) MLF-16 Industrial 833L with Pb-Free bar line indicator NiPdAu Pb-Free Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. 16-Pin MLF(R) (MLF-16) PIN DESCRIPTION Pin Number Pin Name Pin Function 15, 16 1, 2 3, 4 5, 6 Q0, /Q0 Q1, /Q1 Q2, /Q2 Q3, /Q3 LVDS Differential (Outputs): Normally terminated with 100 across the pair (Q, /Q). See "LVDS Outputs" section, Figure 2a. Unused outputs should be terminated with a 100 resistor across each pair. 8 EN This single-ended TTL/CMOS-compatible input functions as a synchronous output enable. The synchronous enable ensures that enable/disable will only occur when the outputs are in a logic LOW state. Note that this input is internally connected to a 25k pull-up resistor and will default to logic HIGH state (enabled) if left open. 9, 12 /IN, IN Differential Inputs: These input pairs are the differential signal inputs to the device. Inputs accept AC- or DC-Coupled differential signs as small as 100mV. Each pin of a pair internally terminates to a VT pin through 50. Note that these inputs will default to an intermediate state if left open. Pleae refer to the "Input Interface Applications" section for more details. 10 VREF-AC Reference Voltage: These outputs bias to VCC-1.4V. They are used when AC coupling the inputs (IN, /IN). For AC-Coupled applications, connect VREF-AC to VT pin and bypass with 0.01F low ESR capacitor to VCC. See "Input Interface Applications" section for more details. Maximum sink/source current is 1.5mA. Due to the limited drive capability, each VREF-AC pin is only intended to drive its respective VT pin. 11 VT Input Termination Center-Tap: Each side of the differential input pair terminates to a VT pin. The VT pins provide a center-tap to a termination network for maximum interface flexibility. See "Input Interface Applications" section for more detaiils. 13 GND Ground. GND pins and exposed pad must be connected to the most negative potential of the device ground. 7, 14 VCC Positive Power Supply: Bypass with 0.1F//0.01F low ESR capacitors and place as close to each VCC pin as possible. TRUTH TABLE IN /IN EN Q /Q 0 1 1 0 1 1 0 1 1 0 0 0(1) 1(1) X Note 1. X On next negative transition of the input signal (IN). August 2007 2 M9999-082407 hbwhelp@micrel.com or (408) 955-1690 Precision Edge(R) SY89833L Micrel, Inc. Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VCC) .................................. -0.5V to +4.0V Input Voltage (VIN) ............................... -0.5V to VCC +0.3V LVDS Output Current (IOUT) ..................................... 10mA Input Current Source or Sink Current on (IN, /IN) .................. 50mA VREF-AC Current Source or Sink Current on (IVT) .......................... 2mA Maximum Operating Junction Temperature .............. 125C Lead Temperature (Soldering, 20 sec.) ..................... 260C Storage Temperature (TS) ....................... -65C to +150C Supply Voltage Range .............................. +3.0V to +3.60V Ambient Temperature (TA) ......................... -40C to +85C Package Thermal Resistance(3) MLF(R) (JA) Still-Air ............................................................. 60C/W MLF(R) (JB) .......................................................... 33C/W DC ELECTRICAL CHARACTERISTICS(4) TA = -40C to +85C, unless otherwise stated. Symbol Parameter VCC Power Supply Voltage Range ICC Power Supply Current RIN Input Resistance (IN-to-VT) RDIFF-IN Condition Min Typ Max Units 3.0 3.3 3.6 V 75 100 mA 45 50 55 Differential Input Resistance (IN-to-/IN) 90 100 110 VIH Input HIGH Voltage (IN, /IN) 0.1 VCC+0.3 V VIL Input LOW Voltage (IN, /IN) -0.3 VIH - 0.1 V VIN Input Voltage Swing (IN, /IN) Note 3, see Figure 2c. 0.1 VCC V VDIFF_IN Differential Input Voltage Note 3, see Figure 2d. 0.2 |IIN| Input Current IN, /IN VREF-AC Reference Voltage No load, max. VCC. V 45 Note 5 VCC-1.525 VCC-1.425 VCC-1.325 mA V Notes: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods may affect device reliability. 2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the device's most negative potential on the PCB. JB and JA values are determined for a 4-layer board in still-air number, unless otherwise stated. 4. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. 5. Due to the internal termination (see "Input Buffer Structure" section) the input current depends on the applied voltages at IN, /IN and VT inputs. Do not apply a combination of voltages that causes the input current to exceed the maximum limit! August 2007 3 M9999-082407 hbwhelp@micrel.com or (408) 955-1690 Precision Edge(R) SY89833L Micrel Inc. LVDS OUTPUTS DC ELECTRICAL CHARACTERISTICS(6) VCC = 3.3V 10%, RL = 100 across the outputs; TA = -40C to +85C Symbol Parameter Condition Min Typ Max Units VOUT Output Voltage Swing See Figure 2c. 250 325 mV VDIFF_OUT Differential Output Voltage Swing See Figure 2d. 500 650 mV VOCM Output Common Mode Voltage VOCM Change in Common Mode Voltage 1.125 1.275 V -50 50 mV Max Units LVTTL/CMOS DC ELECTRICAL CHARACTERISTICS(6) VCC = 3.3V 10%, TA = -40C to +85C Symbol Parameter Condition Min Typ VIH Input HIGH Voltage 2.0 VCC V VIL Input LOW Voltage 0 0.8 V IIH Input HIGH Current -125 30 A IIL Input LOW Current -300 A Note: 6. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. August 2007 4 M9999-082407 hbwhelp@micrel.com or (408) 955-1690 Precision Edge(R) SY89833L Micrel, Inc. AC ELECTRICAL CHARACTERISTICS(7) VCC = +3.3V 10%; RL = 100 across the outputs; TA = -40C to +85C unless otherwise stated. Symbol Parameter Condition Min fMAX Maximum Frequency VOUT 200mV 2.0 tpd Propagation Delay IN-to-Q VIN < 400mV 400 500 600 ps IN-to-Q VIN 400mV 330 440 530 ps 5 20 ps 200 ps tSKEW Within-Device Skew Note 8 Part-to-Part Skew Note 9 Typ Max Units GHz tS Set-Up Time EN to IN, /IN Note 10 300 ps tH Hold Time EN to IN, /IN Note 10 500 ps tJITTER Data Random Jitter (RJ) Deterministic Jitter (DJ) Note 11 Note 12 1 10 psRMS psPP Clock Cycle-to-Cycle Jitter Total Jitter (TJ) Note 13 Note 14 1 10 psRMS psPP 190 ps tr, tf Output Rise/Fall Times (20% to 80%) At full output swing. 60 110 Notes: 7. High-frequency AC parameters are guaranteed by design and characterization. 8. Within device skew is measured between two different outputs under identical input transitions. 9. Part-to-part skew is defined for two parts with identical power supply voltages at the same temperature and no skew at the edges at the respective inputs. 10. Set-up and hold times apply to synchronous applications that intend to enable/disable before the next clock cycle. For asynchronous applications, set-up and hold times do not apply. 11. Random jitter is measured with a K28.7 pattern, measured at fMAX. 12. Deterministic jitter is measured at 2.5Gbps with both K28.5 and 223-1 PRBS pattern. 13. Cycle-to-cycle jitter definition: The variation period between adjacent cycles over a random sample of adjacent cycle pairs. tJITTER_CC = Tn -Tn+1, where T is the time between rising edges of the output signal. 14. Total jitter definition: with an ideal clock input frequency of fMAX (device), no more than one output edge in 1012 output edges will deviate by more than the specified peak-to-peak jitter value. TIMING DIAGRAM EN VCC/2 tS VCC/2 tH /IN IN VIN tpd tpd /Q VOUT Q August 2007 5 M9999-082407 hbwhelp@micrel.com or (408) 955-1690 Precision Edge(R) SY89833L Micrel Inc. TYPICAL OPERATING CHARACTERISTICS VCC = 3.3V, GND = 0V, VIN = 400mV, RL = 100 across the outputs, TA = 25C, unless otherwise stated. Propagation Delay vs. Input Voltage Swing Output Swing vs. Frequency 600 PROPAGATION DELAY (ps) 350 AMPLITUDE (mV) 300 250 200 150 100 50 0 August 2007 500 400 300 200 100 0 0 0.5 1 1.5 2 FREQUENCY (GHz) 2.5 6 0 200 400 600 800 INPUT VOLTAGE SWING (mV) M9999-082407 hbwhelp@micrel.com or (408) 955-1690 Precision Edge(R) SY89833L Micrel, Inc. FUNCTIONAL CHARACTERISTICS VCC = 3.3V, GND = 0V, VIN = 400mV, RL = 100 across the outputs; TA = 25C, unless otherwise stated. (150mV/div.) -15mV Offset 622MHz Output (150mV/div.) -15mV Offset 155MHz Output TIME (321.9ps/div.) TIME (1.29ns/div.) (150mV/div.) -10mV Offset 1GHz Output TIME (200ps/div.) August 2007 7 M9999-082407 hbwhelp@micrel.com or (408) 955-1690 Precision Edge(R) SY89833L Micrel Inc. INPUT STAGE VCC 1.86k9 1.86k9 1.86k9 1.86k9 IN VT /IN 509 509 GND Figure 1. Simplified Differential Input Buffer LVDS OUTPUTS LVDS specifies a small swing of 325mV typical, on a nominal 1.20V common mode above ground. The common mode voltage has tight limits to permit large variations in ground noise between an LVDS driver and receiver. 50 vOUT 100 vOH, vOL 50 vOH, vOL GND GND Figure 2b. LVDS Common Mode Measurement Figure 2a. LVDS Differential Measurement VOUT, VIN 325mV (typical) 650mV VDIFF_IN, VDIFF_OUT Figure 2d. Differential Swing Figure 2c. Single-Ended Swing August 2007 vOCM, vOCM 8 M9999-082407 hbwhelp@micrel.com or (408) 955-1690 Precision Edge(R) SY89833L Micrel, Inc. INPUT INTERFACE APPLICATIONS VCC = 3.3V VCC = 3.3V VCC = 3.3V VCC = 3.3V IN CML CML VCC /IN /IN LVPECL /IN SY89833L SY89833L NC VCC = 3.3V IN IN NC VCC = 3.3V VT VT VREF-AC VREF-AC SY89833L VCC-2V 0.01F VT 50 NC VREF-AC 0.01F VCC Figure 3a. DC-Coupled CML Input Interface VCC = 3.3V VCC = 3.3V Figure 3b. AC-Coupled CML Input Interface VCC = 3.3V VCC = 3.3V IN IN LVPECL LVDS /IN /IN SY89833L Rpd 100 Rpd 100 Figure 3c. DC-Coupled LVPECL Input Interface SY89833L VT VREF-AC 0.01F NC VT NC VREF-AC VCC Figure 3d. AC-Coupled LVPECL Input Interface Figure 3e. LVDS Input Interface RELATED PRODUCT AND SUPPORT DOCUMENTS Part Number Function Data Sheet Link SY89830U 2.5V/3.3V/5V 2.5GHz 1:4 PECL/ECL Clock Driver with 2:1 Differential Input MUX http://www.micrel.com/product-info/products/sy89830u.shtml SY89831U Ultra-Precision 1:4 LVPECL Fanout Buffer/ Translator with Internal Termination http://www.micrel.com/product-info/products/sy89831u.shtml SY89832U 2.5V Ultra-Precision 1:4 LVDS Fanout Buffer/ Translator with Internal Termination http://www.micrel.com/product-info/products/sy89832u.shtml SY89834U 2.5/3.3V Two Input, 1GHz LVTTL/CMOS-to-LVPECL http://www.micrel.com/product-info/products/sy89834u.shtml 1:4 Fanout Buffer/Translator HBW Solutions August 2007 16-MLF(R) Manufacturing Guidelines Exposed Pad Application Note http://www.amkor.com/products/notes_papers/MLF_appnote_0301.pdf New Products and Termination App. Note http://www.micrel.com/product-info/as/solutions.shtml 9 M9999-082407 hbwhelp@micrel.com or (408) 955-1690 Precision Edge(R) SY89833L Micrel Inc. 16-PIN EPAD MicroLeadFrame(R) (MLF-16) Package EP- Exposed Pad Die CompSide Island Heat Dissipation Heat Dissipation VEE Heavy Copper Plane VEE Heavy Copper Plane PCB Thermal Consideration for 16-Pin MLF(R) Package (Always solder, or equivalent, the exposed pad to the PCB) Package Notes: 1. Package meets Level 2 moisture sensitivity classification, and are shipped in dry-pack form. 2. Exposed pads must be soldered to a ground for proper thermal management. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2005 Micrel, Incorporated. August 2007 10 M9999-082407 hbwhelp@micrel.com or (408) 955-1690