751-2411-N09 - CORSAIR ELECTRICAL CONNECTORS INC.

DATASHEET

IDT XO HCMOS Crystal Oscillator XLH

General Description

The XLH is an HCMOS Crystal Oscillator with 750fs typical

phase jitter over 12kHz to 20 MHz bandwidth. Available in a

wide frequency range from 0.750MHz to 250MHz, the IDT

XLH Series Crystal Oscillator utilizes a family of proprietary

ASICs, with a key focus on noise reduction technologies.

The 3rd order Delta Sigma Modulator reduces noise to the

levels that are comparable to traditional Bulk Quartz and SA W

oscillators. With short lead-time, low cost, low noise, wide

frequency range, excellent ambient performance, the XLH is

an excellent choice over the conventional technologies. The

XLH has stabilities as tight as ±20ppm with extremely quick

delivery for both standard and custom frequencies

Features

•Frequency range: 0.750 to 250 MHz

•Output Type: HCMOS/LVCMOS Compatible

•Frequency Stability: ± 20ppm, ± 25ppm, ± 50ppm, or ± 100

ppm

•Supply Voltage: 2.5V or 3.3V

•Phase Jitter (1.875MHz to 20MHz): 225fs typical

•Phase Jitter (12kHz to 20MHz): 750fs typical

•Package options: 3.2mm x 2.5mm x 1.0mm (JX4)

5.0mm x 3.2mm x 1.2mm (JS4)

7.0mm x 5.0mm x 1.3mm (JU4)

•Operating Temperatures: -20°C to +70°C or -40°C to +85°C

Pin Assignment

Pin Descriptions

1. Pulled high internally.

Pin Number Pin Name Description

1 E/D Enable/Disable1 (0=Output Disabled)

2 GND Connect to ground

3 OUT Output

4 VDD Supply voltage

6-pin CLCC

E/D

OUT

VDD

GND

IDT XO HCMOS CRYSTAL OSCILLATOR 2 OCTOBER 28, 2016

XLH DATASHEET

Absolute Maximum Ratings

Stresses above the ratings listed below can cause permanent damage to the XLH. These ratings, which are standard values for

IDT commercially rated p arts, are stress ratings only. Fu nctional operatio n of the device at th ese o r any other cond itions abov e

those indicated in the operation al sections of the specifications is not implied. Exposure to abso lute ma ximum r ating co nditi ons

for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating

temperature range.

ESD Compliance

Mechanical Testing

Solder Reflow Profile

Item Rating

VDD -0.5 to +5.0 V

E/D -0.5 V to VDD + 0.5 V

OUT -0.5 V to VDD + 0. 5 V

Storage Temperature -55°C to 125°C

Theta Ja (Junction to Ambient) 102°C/W – Still Air

Human Body Model (HBM 1000V

Machine Model (MM) 150V

Parameter Test Method

Mechanical Shock Drop from 75cm to hardwood surface–3 times

Mechanical Vibration 10~55Hz, 1.5mm amplitude, 1 minute sweep

2 hours each in 3 directions (X, Y, Z)

High Temperature Burn-in Under power @ 125°C for 2000 hours

Hermetic Seal He pressure: 4 ±1kgf/cm2 2 hour soak

tP10 seconds Max within

5°C of 260°C peak

Ramp down not

to exceed 6°C/s

Ramp up 3°C/s Max

120 ±20 seconds

in pre-heating

area

50 ±10

seconds

above 225°C

reflow area

400 seconds MAX from +25°C to 260°C peak

25°C

160°C

180°C

225°C

260°C

OCTOBER 28, 2016 3 IDT XO HCMOS CRYSTAL OSCILLATOR

XLH DATASHEET

DC Characteristics

(VDD= 3.3 V ± 5%, TA= - 20°C to +70°C; -40° to +85°C)

* A pullup resistor from pin 4 (VDD) to pin 1 (E/D) enables output when pin 1 is left open.

AC Characteristics

(VDD= 3.3 V ± 5%, TA= - 20°C to +70°C; -40° to +85°C)

Note: Inclusive of initi al frequ ency accuracy, operating temperatu re r ange, sup ply varia tion, load va riat ion, 3 ti mes solder ref low, shock, vibration and 1 year aging a t 25°C. W e do not

recommend hand so ldering the devices

Parameter Symbol Condition Min Typ Max Units

Power Supply Current IDD Standard Frequencies 55 mA

Output HIGH Voltage VOH Fout = 0.750 to 150MHz

Fout = 150+ to 250MHz 90%VDD

80%VDD

Output LOW Voltage VOL Fout = 0.750 to 150MHz

Fout = 150+ to 250MHz 10%VDD

20%VDD

Enable/Disable Input HIGH Voltage

(Output enabled)* VIH 70%VDD V

Enable/Disable Input LOW V o ltage

(Output disabled) VIL 30%VDD V

Parameter Symbol Condition Min Typ Max Units

Output Frequency Range FOUTR 0.750 250 MHz

Frequency Stability Temperatu re = -20°C to +70°C ±20 ±100 ppm

Temperature = -40°C to +85°C ±25 ±100 ppm

Aging (1st year) Ta = 25°C ±3

Aging (10 years) Ta = 25°C ±10

Output Load 15 pF

Start-up Time TST Output valid time after VDD meets

minimum specified level 10 ms

Output Rise Time 20% to 80% VDD 3ns

Output Fall Time 80% to 20% VDD 3ns

Duty Cycle TDTCY @ 50% VDD 45 55 %

Output Enable/ Disable Time TOE 100 ns

Period Jitter, RMS JPER Frequency = 125MHz 3 psec

Random Jitter RJFrequency = 125MHz

Per MJSQ spec (Methodologies for

Jitter and Signal Quality specifications)

1.2 psec

Deterministic Jitter DJ8psec

Total Jitter TJ25.2 psec

Phase Jitter (12kHz – 20MHz) JITTER Frequency = 125MHz 0.75 psec

Phase Noise Performance

Frequency = 125 MHz NOISE 100Hz of Carrier -95 dBc/Hz

1kHz of Carrier -118 dBc/Hz

10kHz of Carrier -120 dBc/Hz

100kHz of Carrier -124 dBc/Hz

1MHz of Carrier -143 dBc/Hz

10MHz of Carrier -153 dBc/Hz

Output Frequency (Standards) FOUT 10MHz, 12MHz, 12.288MHz, 16MHz, 20MHz, 24MHz, 24.576MHz, 25MHz,

33.333MHz, 40MHz, 48MHZ , 50MHz, 100MHz, 125MHz, 156.25MHz

(Contact IDT for additional frequencies)

IDT XO HCMOS CRYSTAL OSCILLATOR 4 OCTOBER 28, 2016

XLH DATASHEET

DC Characteristics

(VDD= 2.5 V ± 5%, TA= - 20°C to +70°C; -40° to +85°C)

* A pullup resistor from pin 4 (VDD) to pin 1 (E/D) enables output when pin 1 is left open.

AC Characteristics

(VDD= 2.5 V ± 5%, TA= - 20°C to +70°C; -40° to +85°C)

Note: Inclusive of initi al frequ ency accuracy, operating temperatu re r ange, sup ply varia tion, load va riat ion, 3 ti mes solder ref low, shock, vibration and 1 year aging a t 25°C. W e do not

recommend hand so ldering the devices

Parameter Symbol Condition Min Typ Max Units

Power Supply Current IDD Standard Frequencies 35 mA

Output HIGH Voltage VOH Fout = 0.750 to 160MHz

Fout = 160+ to 180MHz 10%VDD

20%VDD

Output LOW Voltage VOL Fout = 0.750 to 160MHz

Fout = 160+ to 180MHz 10%VDD

20%VDD

Enable/Disable Input HIGH Voltage

(Output enabled)* VIH 70%VDD V

Enable/Disable Input LOW V o ltage

(Output disabled) VIL 30%VDD V

Parameter Symbol Condition Min Typ Max Units

Output Frequency Range FOUTR 0.750 180 MHz

Frequency Stability Temperatu re = -20°C to +70°C ±20 ±100 ppm

Temperature = -40°C to +85°C ±25 ±100 ppm

Output Load 15 pF

Start-up Time TST Output valid time after VDD meets

minimum specified level 10 ms

Output Rise Time 20% to 80% VDD 3ns

Output Fall Time 80% to 20% VDD 3ns

Duty Cycle TDTCY @ 50% VDD 45 55 %

Output Enable/ Disable Time TOE 100 ns

Period Jitter, RMS JPER Frequency = 125MHz 3.3 psec

Random Jitter RJFrequency = 125MHz

Per MJSQ spec (Methodologies for

Jitter and Signal Quality specifications)

1.3 psec

Deterministic Jitter DJ6.7 psec

Total Jitter TJ25.6 psec

Phase Jitter (12kHz – 20MHz) JITTER Frequency = 125MHz 0.85 psec

Phase Noise Performance

Frequency = 125 MHz NOISE 100Hz of Carrier -91 dBc/Hz

1kHz of Carrier -107 dBc/Hz

10kHz of Carrier -117 dBc/Hz

100kHz of Carrier -123 dBc/Hz

1MHz of Carrier -140 dBc/Hz

10MHz of Carrier -149 dBc/Hz

Output Frequency (Standards) FOUT 10MHz, 12MHz, 12.288MHz, 16MHz, 20MHz, 24MHz, 24.576MHz, 25MHz,

33.333MHz, 40MHz, 48MHZ , 50MHz, 100MHz, 125MHz, 156.25MHz

(Contact IDT for additional frequencies)

OCTOBER 28, 2016 5 IDT XO HCMOS CRYSTAL OSCILLATOR

XLH DATASHEET

Output Waveform

Typical Phase Noise (3.3V)

IDT XO HCMOS CRYSTAL OSCILLATOR 6 OCTOBER 28, 2016

XLH DATASHEET

JS4 Package Outline and Dimensions

OCTOBER 28, 2016 7 IDT XO HCMOS CRYSTAL OSCILLATOR

XLH DATASHEET

JS4 Package Outline and Dimensions (cont.)

IDT XO HCMOS CRYSTAL OSCILLATOR 8 OCTOBER 28, 2016

XLH DATASHEET

JU4 Package Outline and Dimensions

OCTOBER 28, 2016 9 IDT XO HCMOS CRYSTAL OSCILLATOR

XLH DATASHEET

JU4 Package Outline and Dimensions (cont.)

IDT XO HCMOS CRYSTAL OSCILLATOR 10 OCTOBER 28, 2016

XLH DATASHEET

JX4 Package Outline and Dimensions

OCTOBER 28, 2016 11 IDT XO HCMOS CRYSTAL OSCILLATOR

XLH DATASHEET

JX4 Package Outline and Dimensions (cont.)

IDT XO HCMOS CRYSTAL OSCILLATOR 12 OCTOBER 28, 2016

XLH DATASHEET

IDT Ordering Information Scheme #1 (for reference only)

The IDT Ordering Information Scheme #1 table above is to be used for reference only. IDT is updating the orderable part

number for this device family to support frequency accuracy and ordering down to the 1Hz level. Please see the IDT

Ordering Information Scheme #2 table on the following page for the latest ordering information.

FamilyandASIC

OutputType

Package

Voltage

Precision

125.000

Frequency

JS6

Package

TemperatureRange

I: Industrialrange–40to+85°C

K: Extendedindustrialrange–40to+105°C

X: Extendedcommercialrange–20to+70°C

2:Automotiverange–40to+105°C

3:Automotiverange–40to+85°C

4:Automotiverange–20to+70°C

JU6,JU4*:7050package(7.0x5.0mm)

JS6,JS4*: 5032package(5.0x3.2mm)

JX6,JX4*: 3225package(3.2x2.5mm)

*HCMOSOutputOnly

125.000:FrequencyinMHzforfrequenciesabove100kHz“.”in4th digit

032K768:FrequencyinkHzforfrequenciesbelow100kHz“K”in4th digit

156.25A:Letteraslastcharactersinfrequenciesfieldindicatesupto4moredigits

existforthefrequency. Example: 156.25Ais156.253906MHz

A00.000toA99.999 1000MHzto1099.999MHz

B00.000toB99.999 1100MHzto1199.999MHz

C00.000toC99.9991200MHzto1299.999MHz

D00.000toD99.999 1300MHzto1399.999MHz

7characterstotalforfrequencyfield

V: 50ppmAPR(VCXO)

0:±100ppm

5: ±50ppm

6:±25ppm

8: ±20ppm

1: 1.8VDC±5%

2:2.5VDC±5%

3: 3.3VDC±5%

3:3.2x2.5mm

5: 5.0x3.2mm

7:7.0x5.0mm

H:HCMOSEnable/DisablePin1

J: HCMOSEnable/DisablePin2

L:LVDSEnable/DisablePin1

M:LVDSEnable/DisablePin2

P:LVPECLEnable/DisablePin1

Q:LVPECLEnable/DisablePin2

N:HCSLEnable/DisablePin1

O:HCSLEnable/DisablePin2

X:XHCMOSCompHCMOSEnable/DisablePin1

Y:XHCMOSCompHCMOSEnable/DisablePin2

XL: 1,000fsjitter

XU:400fsjitter

XA:1,000fsjitter(Automotive)

XB:400fsjitter(Automotive)



OCTOBER 28, 2016 13 IDT XO HCMOS CRYSTAL OSCILLATOR

XLH DATASHEET

IDT Ordering Information Scheme #2

FamilyandASIC

OutputType

Package

Voltage

Precision

125.000000

Frequency

TemperatureRange

I: Industrialrange–40to+85°C

K: Extendedindustrialrange–40to+105°C

X: Extendedcommercialrange–20to+70°C

2:Automotiverange–40to+105°C

3:Automotiverange–40to+85°C

4:Automotiverange–20to+70°C

125.000000ListedinMHzto6digits

000.016000MHzto999.999999MHz

A00.000000toA99.999999 1000MHzto1099.999MHz

B00.000000toB99.999999 1100MHzto1199.999MHz

C00.000000toC99.9999991200MHzto1299.999MHz

D00.000000toD99.999999 1300MHzto1399.999MHz

E00.000000toD99.999999 1400MHzto1499.999MHz

F00.0000001500MHz

V: 50ppmAPR(VCXO)

0:±100ppm

5: ±50ppm

6:±25ppm

8: ±20ppm

1: 1.8VDC±5%

2:2.5VDC±5%

3: 3.3VDC±5%

3:3.2x2.5mm

5: 5.0x3.2mm

7:7.0x5.0mm

H:HCMOSEnable/DisablePin1

J: HCMOSEnable/DisablePin2

L:LVDSEnable/DisablePin1

M:LVDSEnable/DisablePin2

P:LVPECLEnable/DisablePin1

Q:LVPECLEnable/DisablePin2

N:HCSLEnable/DisablePin1

O:HCSLEnable/DisablePin2

X:XHCMOSCompHCMOSEnable/DisablePin1

Y:XHCMOSCompHCMOSEnable/DisablePin2

XL: 1,000fsjitter

XU:400fsjitter

XA:1,000fsjitter(Automotive)

XB:400fsjitter(Automotive)



DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole di scr etio n. All informatio n i n

this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined

in the indepe ndent stat e and are n ot gua rant eed to per form th e same w ay when insta lled i n cu stomer p rodu cts. The info rmati on con tain ed he re in is provi ded with out rep resen tati on or wa rranty o f a ny kin d, w hethe r

express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchanta bility, or non-inf ringeme nt of the inte llectual pr operty ri ghts of oth ers. This

document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties.

IDT’s products are not intended for use in applications involving extre me en vironmen tal co nd itions o r in life sup port systems or similar devices whe re th e fa ilure or malfu ncti o n o f an ID T pr od uct ca n b e r ea sonably

expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.

Integrated Device Te chn olog y, IDT and the IDT lo go ar e r eg ister ed tr ad emar ks o f ID T. Pr odu ct sp eci fication subject to cha ng e wi th out notice. Othe r tr ade m ar ks an d se r vice m ar ks u sed herein, in cluding protecte d

names, logos and designs, are the property of IDT or their respective third party owners.

Corporate Headquarters

6024 Silver Creek Valley Road

San Jose, CA 95138 USA

www.IDT.com

Sales

1-800-345-7015 or 408-284-8200

Fax: 408-284-2775

www.IDT.com/go/sales

Tech Support

www.idt.com/go/support

Revision History

Rev. Date Originat or Description of Change

A 10/01/14 B. Chandhoke 1. Corrected typo in spec for Enable/Disable Low Voltage; from >30%VDD to <30%VDD.

2. Moved from Advance to Preliminary.

B 12/10/14 B. Chandhoke 1. Added 7 x 5 x 1.3mm JU4 and 3.2 x 2.5 x 1.0mm JX4 package options and package

dimension/landing pattern drawings.

2. Updated ordering information table/graphic to show added package options.

C 10/28/16 P. Jenkins Update ordering information decoder tables by separating them into Scheme 1 and

Scheme 2; add note to distinguish the two tables.