SEMICONDUCTOR TECHNICAL DATA High-Performance Silicon-Gate CMOS N SUFFIX PLASTIC PACKAGE CASE 648-08 16 The MC74HC194 is identical in pinout to the LS194 and the MC14194B metal gate CMOS device. The device inputs are compatible with standard CMOS outputs; with pull-up resistors, they are compatible with LSTTL outputs. This static shift register features parallel load, serial load (shift right and shift left), hold, and reset modes of operation. These modes are tabulated in the Function Table, and further explanation can be found in the Pin Description section. 1 ORDERING INFORMATION MC74HCXXXN * * * * * * Output Drive Capability: 10 LSTTL Loads Outputs Directly Interface to CMOS, NMOS, and TTL Operating Voltage Range: 2 to 6 V Low Input Current: 1 A High Noise Immunity Characteristic of CMOS Devices In Compliance with the Requirements Defined by JEDEC Standard No. 7A * Chip Complexity 164 FETs or 41 Equivalent Gates PIN ASSIGNMENT RESET 1 16 SA 2 15 VCC QA A 3 14 QB B 4 13 QC C 5 12 QD LOGIC DIAGRAM 2 SA SERIAL DATA INPUTS 7 SD A PARALLEL DATA INPUTS B C 15 3 14 4 13 5 12 QA QB QC QD 6 D Plastic D 6 11 CLOCK SD 7 10 S1 GND 8 9 S0 PARALLEL DATA OUTPUTS 11 CLOCK 10 9 1 MODE S1 SELECT S0 RESET VCC = PIN 16 GND = PIN 8 FUNCTION TABLE Inputs Mode Select Serial Data Parallel Data Outputs Operating Mode Reset S1 S0 Clock SD SA A B C D QA QB QC QD L X X X X X X X X X L L L L Reset H H H X X a b c d a b c d Parallel Load H H L L H H X X H L X X X X X X X X H L QAn QAn QBn QBn QCn QCn H H H H L L H L X X X X X X X X X X QBn QBn QCn QCn QDn QDn H L H H H L X X L X X X X X X X X X X X X X X X X X X X X X L H H = high level (steady state) L = low level (steady state) X = don't care = transition from low to high level. No Change No Change No Change Shift Left Hold a, b, c, d = the level of steady-state input at inputs A, B, C, or D, respectively. QAn, QBn, QCn, QDn = the level of QA, QB, QC, or QD, respectively, before the most recent transition of the clock. 10/95 Motorola, Inc. 1995 Shift Right 1 REV 6 IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII III IIIIIIIIIIIIII IIIIII III IIIIIIIIIIIIIIIIIIIIIII III IIIIIIIIIIIIII IIIIII III IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII v v IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIII IIIIII IIIIIIIIIIIIIII IIIIIIIIIIIII IIIIIIIII IIII IIIIIIIIIIIIII IIIIII IIIIII IIIIIIIII IIIIIIIIIIIII IIIIIIIII IIII IIII IIII III IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIII III IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII v IIII v III IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII v IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIII IIII III IIII IIII III v IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII v IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII v IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII v IIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIII v IIIIIIIIIIIIIIIIIIIIII IIII III IIII IIII III v IIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIII v IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII MC74HC194 MAXIMUM RATINGS* Symbol VCC Parameter DC Supply Voltage (Referenced to GND) Value Unit - 0.5 to + 7.0 V V Vin DC Input Voltage (Referenced to GND) - 1.5 to VCC + 1.5 Vout DC Output Voltage (Referenced to GND) - 0.5 to VCC + 0.5 V DC Input Current, per Pin 20 mA Iout DC Output Current, per Pin 25 mA ICC DC Supply Current, VCC and GND Pins 50 mA PD Power Dissipation in Still Air 750 mW Tstg Storage Temperature - 65 to + 150 _C Iin TL Plastic DIP This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND (Vin or Vout) VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. _C Lead Temperature, 1 mm from Case for 10 Seconds (Plastic DIP) 260 * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. Derating -- Plastic DIP: - 10 mW/_C from 65_ to 125_C For high frequency or heavy load considerations, see Chapter 2 of the Motorola High-Speed CMOS Data Book (DL129/D). RECOMMENDED OPERATING CONDITIONS Symbol VCC Vin, Vout Parameter DC Supply Voltage (Referenced to GND) Min Max Unit 2.0 6.0 V 0 VCC V - 55 + 125 _C 0 0 0 1000 500 400 ns DC Input Voltage, Output Voltage (Referenced to GND) TA Operating Temperature, All Package Types tr, tf Input Rise and Fall Time (Figure 1) VCC = 2.0 V VCC = 4.5 V VCC = 6.0 V DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND) Guaranteed Limit Symbol Parameter Test Conditions VCC V - 55 to 25_C 85_C 125_C Unit VIH Minimum High-Level Input Voltage Vout = 0.1 V or VCC - 0.1 V |Iout| 20 A 2.0 4.5 6.0 1.5 3.15 4.2 1.5 3.15 4.2 1.5 3.15 4.2 V VIL Maximum Low-Level Input Voltage Vout = 0.1 V or VCC - 0.1 V |Iout| 20 A 2.0 4.5 6.0 0.3 0.9 1.2 0.3 0.9 1.2 0.3 0.9 1.2 V Minimum High-Level Output Voltage Vin = VIH or VIL |Iout| 20 A 2.0 4.5 6.0 1.9 4.4 5.9 1.9 4.4 5.9 1.9 4.4 5.9 V 4.5 6.0 3.98 5.48 3.84 5.34 3.70 5.20 2.0 4.5 6.0 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 4.5 6.0 0.26 0.26 0.33 0.33 0.40 0.40 VOH Vin = VIH or VIL |Iout| |Iout| VOL Maximum Low-Level Output Voltage Vin = VIH or VIL |Iout| 20 A Vin = VIH or VIL |Iout| |Iout| Iin ICC 4.0 mA 5.2 mA 4.0 mA 5.2 mA V Maximum Input Leakage Current Vin = VCC or GND 6.0 0.1 1.0 1.0 A Maximum Quiescent Supply Current (per Package) Vin = VCC or GND Iout = 0 A 6.0 8 80 160 A NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High-Speed CMOS Data Book (DL129/D). MOTOROLA 2 High-Speed CMOS Logic Data DL129 -- Rev 6 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIII III IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIII III IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII v IIII v III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII MC74HC194 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns) Guaranteed Limit VCC V - 55 to 25_C 85_C 125_C Unit fmax Maximum Clock Frequency (50% Duty Cycle) (Figures 1 and 4) 2.0 4.5 6.0 6.0 30 35 4.8 24 28 4.0 20 24 MHz tPLH, tPHL Maximum Propagation Delay, Clock to Q (Figures 1 and 4) 2.0 4.5 6.0 145 29 25 180 36 31 220 44 38 ns tPHL Maximum Propagation Delay, Reset to Q (Figures 2 and 4) 2.0 4.5 6.0 150 30 26 190 38 33 225 45 38 ns tTLH, tTHL Maximum Output Transition Time, Any Output (Figures 1 and 4) 2.0 4.5 6.0 75 15 13 95 19 16 110 22 19 ns Maximum Input Capacitance -- 10 10 10 pF Symbol Cin Parameter NOTES: 1. For propagation delays with loads other than 50 pF, see Chapter 2 of the Motorola High-Speed CMOS Data Book (DL129/D). 2. Information on typical parametric values can be found in Chapter 2 of the Motorola High-Speed CMOS Data Book (DL129/D). Typical @ 25C, VCC = 5.0 V CPD Power Dissipation Capacitance (Per Package)* pF 90 IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIII III IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIII IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIII IIII IIII III v v IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII * Used to determine the no-load dynamic power consumption: PD = CPD VCC 2 f + ICC VCC . For load considerations, see Chapter 2 of the Motorola High-Speed CMOS Data Book (DL129/D). TIMING REQUIREMENTS (Input tr = tf = 6 ns) Guaranteed Limit VCC V - 55 to 25_C 85_C 125_C tsu Minimum Setup Time, Parallel Data Inputs to Clock (Figure 3) 2.0 4.5 6.0 100 20 17 125 25 21 150 30 26 ns tsu Minimum Setup Time, S1 or S2 to Clock (Figure 3) 2.0 4.5 6.0 100 20 17 125 25 21 150 30 26 ns tsu Minimum Setup Time, SA or SD to Clock (Figure 3) 2.0 4.5 6.0 100 20 17 125 25 21 150 30 26 ns th Minimum Hold Time, Clock to any Input (except Reset) (Figure 3) 2.0 4.5 6.0 3 3 3 3 3 3 3 3 3 ns Minimum Recovery Time, Reset Inactive to Clock (Figure 2) 2.0 4.5 6.0 5 5 5 5 5 5 5 5 5 ns tw Minimum Pulse Width, Clock (Figure 1) 2.0 4.5 6.0 80 16 14 100 20 17 120 24 20 ns tw Minimum Pulse Width, Reset (Figure 2) 2.0 4.5 6.0 80 16 14 100 20 17 120 24 20 ns Maximum Input Rise and Fall Times (Figure 1) 2.0 4.5 6.0 1000 500 400 1000 500 400 1000 500 400 ns Symbol trec tr, tf Parameter Unit NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High-Speed CMOS Data Book (DL129/D). High-Speed CMOS Logic Data DL129 -- Rev 6 3 MOTOROLA MC74HC194 PIN DESCRIPTIONS DATA INPUTS Reset (Pin 1) A, B, C, D (Pins 3, 4, 5, 6) A low level applied to this pin resets all stages and forces all outputs low. Parallel data inputs. S0, S1 (Pins 9, 10) Mode-select inputs. These inputs control the mode of operation as described in the function table and below. SA (Pin 2) Serial-data input when using shift-right mode. Parallel Load Mode (S1 = H, S0 = H) Data is loaded into the device with a positive transition of the Clock input. SD (Pin 7) Serial-data input when using shift-left mode. Shift Right Mode (S1 = L, S0 = H) With a positive transition of the Clock input, each bit is shifted right (in the direction QA toward QD) one stage and data on the SA Serial Data Input is shifted into stage A. OUTPUTS QA, QB, QC, QD (Pins 15, 14, 13, 12) Parallel data outputs. Clock (Pin 11) Shift Left Mode (S1 = H, S0 = L) With a positive transition of the Clock input, each bit is shifted left (in the direction QD toward QA) one stage and data on the SD Serial Data Input is shifted into stage D. Clock Input. The shift register is completely static, allowing Clock rates down to DC in a continuous or intermittent mode. Hold Mode (S1 = L, S0 = L) Outputs are held. CONTROL INPUTS SWITCHING WAVEFORMS tr tw tf VCC VCC 90% 50% 10% tw CLOCK GND GND tPHL 1/fmax tPLH Q 50% RESET 50% Q tPHL trec 90% 50% 10% VCC CLOCK tTLH 50% GND tTHL Figure 1. Figure 2. TEST POINT OUTPUT VALID VCC DATA OR MODE DEVICE UNDER TEST 50% GND tsu th CL* VCC CLOCK 50% GND * Includes all probe and jig capacitance Figure 3. MOTOROLA Figure 4. Test Circuit 4 High-Speed CMOS Logic Data DL129 -- Rev 6 High-Speed CMOS Logic Data DL129 -- Rev 6 S1 9 5 RESET 1 11 10 CLOCK MODE SELECT INPUTS S0 SERIAL DATA INPUT, SD 7 6 D C C Q R R D C C Q R R 12 QD D 5 C Q R R D C PARALLEL DATA OUTPUTS 13 QC C PARALLEL DATA INPUTS EXPANDED LOGIC DIAGRAM 4 14 QB B 3 C Q R R D C A 15 QA SERIAL DATA INPUT, SA 2 MC74HC194 MOTOROLA MC74HC194 TIMING DIAGRAM CLOCK MODE- SELECT INPUTS S0 S1 RESET SERIAL DATA INPUTS SA SD A PARALLEL DATA INPUTS B H L C H D L QA PARALLEL DATA OUTPUTS QB QC QD SHIFT RIGHT SHIFT LEFT RESET LOAD MOTOROLA INHIBIT RESET 6 High-Speed CMOS Logic Data DL129 -- Rev 6 MC74HC194 OUTLINE DIMENSIONS N SUFFIX PLASTIC PACKAGE CASE 648-08 ISSUE R NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. -A - 16 9 1 8 B F C L S -T - SEATING PLANE K H D 16 PL 0.25 (0.010) M M J G T A M DIM A B C D F G H J K L M S INCHES MILLIMETERS MIN MAX MIN MAX 0.740 0.770 18.80 19.55 6.35 0.250 0.270 6.85 3.69 0.145 0.175 4.44 0.39 0.015 0.021 0.53 1.02 0.040 0.070 1.77 0.100 BSC 2.54 BSC 0.050 BSC 1.27 BSC 0.21 0.008 0.015 0.38 2.80 0.110 0.130 3.30 7.50 0.295 0.305 7.74 0 0 10 10 0.020 0.040 0.51 1.01 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Toshikatsu Otsuki, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-3521-8315 MFAX: RMFAX0@email.sps.mot.com -TOUCHTONE (602) 244-6609 INTERNET: http://Design-NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 High-Speed CMOS Logic Data DL129 -- Rev 6 CODELINE 7 *MC74HC194/D* MC74HC194/D MOTOROLA