DETAIL SPECIFICATION SHEET
ADAPTER, CONNECTORS, RECEPTACLE, ELECTRICAL, THRU-BULKHEAD
MOUNTING, FLANGE, BAYONET COUPLING, SERIES 1
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
The requirements for acquiring the product described herein
shall consist of this specification sheet and MIL-DTL-26482.
Inactive for new design after 15 December 1998.
MS3119E
w/AMENDMENT 2
3 April 2009
SUPERSEDING
w/AMENDMENT 1
31 July 2008
INCH-POUND
FIGURE 1. Receptacle, class E, dimensions and configurations.
AMSC N/A FSC 5935
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:00Z
Check the source to verify that this is the current version before use.
MS3119E
w/AMENDMENT 2
2
FIGURE 1. Receptacle, class E, dimensions and configurations - Continued.
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:00Z
Check the source to verify that this is the current version before use.
MS3119E
w/AMENDMENT 2
3
Shell
size
A
max
length
side
B
(TP)
mounting
holes
D
max
insert
dia
pin
F
+ .031
- .000
mounting
flange
location
socket side
G
.016
thick
mounting
flange
H
.005
dia
mounting
holes
8 .828
(21.03) .594 (15.09) .347 (8.81)
10 .954
(24.23) .719 (18.26) .464 (11.79)
12 1.047
(26.59) .812 (20.62) .581 (14.76)
14 1.141
(28.98) .906 (23.01) .703 (17.86)
16 1.234
(31.34) .969 (24.61) .828 (21.03)
18 1.328
(33.73) 1.062 (26.97) .938 (23.83)
.562 (14.27) .062 (1.57)
20 1.453
(36.91) 1.156 (29.36) 1.063 (27.00)
22 1.578
(40.08) 1.250 (31.75) 1.188 (30.18)
.120 (3.05)
24 1.703
(43.26) 1.375 (34.93) 1.313 (33.35)
.688 (17.48) .094 (2.39)
.147 (3.73)
Shell
size L
max overall
length
P
min
edge distance
R
max
ID gasket
S
max panel and screw head
rear mount (for front mount,
S = S-G)
8 .378 (9.60)
10 .506 (12.85)
12 .618 (15.70)
14 .745 (18.92)
16 .872 (22.15)
18
1.125 (28.58) .035 (0.89)
.972 (24.69)
.218 (5.54)
20 1.097
(27.86)
22 1.222
(31.04)
.344 (8.74)
24
1.406 (35.71) .050 (1.27)
1.347
(34.21) .311 (7.90)
FIGURE 1. Receptacle, class E, dimensions and configurations - Continued.
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:00Z
Check the source to verify that this is the current version before use.
MS3119E
w/AMENDMENT 2
4
Inches mm Inches mm Inches mm Inches mm
.005 0.13 .015 0.38 .020 0.51 .070 1.78
.010 0.25 .016 0.41 .031 0.79
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. True position (TP) tolerances specified are in accordance with ASME Y14.5M.
FIGURE 1. Receptacle, class E, dimensions and configurations - Continued.
REQUIREMENTS:
Dimensions and configurations: See figure 1.
Connector mating: This connector mates with MS3116 and MS3126.
For insert arrangements: See MIL-STD-1669.
Finishes: A finish designator shall not be included in the PIN when finish W is required. See
MIL-DTL-26482 for optional finishes, including D, T and Z.
Intermateability dimensions are in accordance with MIL-DTL-26482.
Effectivity date: The effective changes to this specification are immediate, from the date of this
specification. Parts shall be date coded in accordance with MIL-DTL-26482 (year and week of
manufacture of product).
Disposition of previous stock shall be in accordance with MIL-DTL-26482.
Application guidance: Users that require a specified F dimension on the pin contact side of the
connector should use DSCC drawing 09005.
Part or Identifying Number (PIN) example:
MS3119 E 12 -3 W D
MS number
Class
Shell size
Insert arrangement
Alternate insert position
Finish
Note: When class W is required, no finish designator is used (class W is the default finish).
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:00Z
Check the source to verify that this is the current version before use.
MS3119E
w/AMENDMENT 2
5
Amendment notations: The margins of this specification are marked with vertical lines to indicate
where modifications from this amendment were made. This was done as a convenience only and
the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders
and contractors are cautioned to evaluate the requirements of this document based on the entire
content irrespective of the marginal notations.
Referenced documents. In addition to MIL-DTL-26482, this document references the following:
MS3116
MS3126
MIL-STD-1669
ASME Y14.5M
DSCC drawing 09005
CONCLUDING MATERIAL
Custodians: Preparing activity:
Army – CR DLA - CC
Navy – AS
Air Force – 85 (Project 5935-2009-051)
DLA – CC
Review activities:
Army – AV
Navy – EC
Air Force – 99
NOTE: The activities listed above were interested in this document as of the date of this document.
Since organizations and responsibilities can change, you should verify the currency of the information
above using the ASSIST Online database at http://assist.daps.dla.mil.
Source: https://assist.dla.mil -- Downloaded: 2018-10-13T10:00Z
Check the source to verify that this is the current version before use.
