LP3962, LP3965 www.ti.com SNVS066H - MAY 2000 - REVISED APRIL 2013 LP3962/LP3965 1.5A Fast Ultra Low Dropout Linear Regulators Check for Samples: LP3962, LP3965 FEATURES DESCRIPTION * * * * * * The LP3962/LP3965 series of fast ultra low-dropout linear regulators operate from a +2.5V to +7.0V input supply. Wide range of preset output voltage options are available. These ultra low dropout linear regulators respond very fast to step changes in load which makes them suitable for low voltage microprocessor applications. The LP3962/LP3965 are developed on a CMOS process which allows low quiescent current operation independent of output load current. This CMOS process also allows the LP3962/LP3965 to operate under extremely low dropout conditions. 1 2 * * * * * * Ultra Low Dropout Voltage Low Ground Pin Current Load Regulation of 0.04% 15A Quiescent Current in Shutdown Mode Specified Output Current of 1.5A DC Available in SOT-223,SFM/TO-263 and TO-220 Packages Output Voltage Accuracy 1.5% Error Flag Indicates Output Status (LP3962) Sense Option Improves Better Load Regulation (LP3965) Extremely Low Output Capacitor Requirements Overtemperature/Overcurrent Protection -40C to +125C Junction Temperature Range APPLICATIONS * * * * * * * * Microprocessor Power Supplies GTL, GTL+, BTL, and SSTL Bus Terminators Power Supplies for DSPs SCSI Terminator Post Regulators High Efficiency Linear Regulators Battery Chargers Other Battery Powered Applications Dropout Voltage: Ultra low dropout voltage; typically 38mV at 150mA load current and 380mV at 1.5A load current. Ground Pin Current: Typically 5mA at 1.5A load current. Shutdown Mode: Typically 15A quiescent current when the shutdown pin is pulled low. Error Flag: Error flag goes low when the output voltage drops 10% below nominal value (for LP3962). SENSE: Sense pin improves regulation at remote loads. (For LP3965) Precision Output Voltage: Multiple output voltage options are available ranging from 1.2V to 5.0V and adjustable (LP3965), with a specified accuracy of 1.5% at room temperature, and 3.0% over all conditions (varying line, load, and temperature). Typical Application Circuits *SD and ERROR pins must be pulled high through a 10k pull-up resistor. Connect the ERROR pin to ground if this function is not used. See Application Hints section for more information. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2000-2013, Texas Instruments Incorporated LP3962, LP3965 SNVS066H - MAY 2000 - REVISED APRIL 2013 www.ti.com *SD and ERROR pins must be pulled high through a 10k pull-up resistor. Connect the ERROR pin to ground if this function is not used. See Application Hints section for more information. Block Diagram LP3962 2 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 LP3962, LP3965 www.ti.com SNVS066H - MAY 2000 - REVISED APRIL 2013 Block Diagram LP3965 Block Diagram LP3965-ADJ Connection Diagram Figure 1. Top View SOT-223-5 Package Figure 2. Top View TO-220-5 Package Bent, Staggered Leads Figure 3. Top View SFM/TO-263-5 Package Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 3 LP3962, LP3965 SNVS066H - MAY 2000 - REVISED APRIL 2013 www.ti.com Pin Descriptions for SOT-223-5 Package LP3962 Pin # Name LP3965 Function Name Function 1 SD Shutdown SD Shutdown 2 VIN Input Supply VIN Input Supply 3 VOUT 4 ERROR 5 GND Output Voltage ERROR Flag VOUT SENSE/ADJ Ground GND Output Voltage Remote Sense Pin or Output Adjust Pin Ground Pin Descriptions for TO-220-5 and SFM/TO-263-5 Packages LP3962 Pin # Name LP3965 Function Name Function 1 SD Shutdown SD Shutdown 2 VIN Input Supply VIN Input Supply 3 GND Ground 4 VOUT Output Voltage 5 ERROR ERROR Flag GND Ground VOUT Output Voltage SENSE/ADJ Remote Sense Pin or Output Adjust Pin These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) -65C to +150C Storage Temperature Range Lead Temperature (Soldering, 5 sec.) ESD Rating 260C (3) Power Dissipation 2 kV (4) Internally Limited -0.3V to +7.5V Input Supply Voltage (Survival) -0.3V to VIN+0.3V Shutdown Input Voltage (Survival) Output Voltage (Survival), (5) (6) -0.3V to +7.5V , IOUT (Survival) Short Circuit Protected Maximum Voltage for ERROR Pin VIN+0.3V Maximum Voltage for SENSE Pin VOUT+0.3V (1) (2) (3) (4) (5) (6) 4 Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is intended to be functional, but does not ensure specific performance limits. For ensured specifications and test conditions, see Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. The human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin. At elevated temperatures, devices must be derated based on package thermal resistance. The devices in TO-220 package must be derated at jA = 50C/W (with 0.5in2, 1oz. copper area), junction-to-ambient (with no heat sink). The devices in the SFM/TO-263 surface-mount package must be derated at jA = 60C/W (with 0.5in2, 1oz. copper area), junction-to-ambient. The devices in SOT-223 package must be derated at jA = 90C/W (with 0.5in2, 1oz. copper area), junction-to-ambient. If used in a dual-supply system where the regulator load is returned to a negative supply, the LP396X output must be diode-clamped to ground. The output PMOS structure contains a diode between the VIN and VOUT terminals. This diode is normally reverse biased. This diode will get forward biased if the voltage at the output terminal is forced to be higher than the voltage at the input terminal. This diode can typically withstand 200mA of DC current and 1Amp of peak current. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 LP3962, LP3965 www.ti.com SNVS066H - MAY 2000 - REVISED APRIL 2013 Operating Ratings (1) 2.5V to 7.0V Shutdown Input Voltage (Operating) -0.3V to VIN+0.3V Input Supply Voltage (Operating), Maximum Operating Current (DC) 1.5A Operating Junction Temp. Range -40C to +125C (1) The minimum operating value for VIN is equal to either [VOUT(NOM) + VDROPOUT] or 2.5V, whichever is greater. Electrical Characteristics LP3962/LP3965 Limits in standard typeface are for TJ = 25C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 10 mA, COUT = 33F, VSD = VIN-0.3V. Symbol Parameter Conditions Typ (1) LP3962/5 (2) Units Min Max 0 -1.5 -3.0 +1.5 +3.0 % 1.198 1.180 1.234 1.253 V Output Voltage Tolerance (3) 10 mA IL 1.5A VOUT +1 VIN 7.0V VADJ Adjust Pin Voltage (ADJ version) 10 mA IL 1.5A VOUT +1.5V VIN 7.0V 1.216 V OL Output Voltage Line Regulation VOUT+1V<VIN<7.0V, 0.02 0.06 % Output Voltage Load Regulation (3) 10 mA < IL < 1.5 A 0.04 0.09 % VO VO/ IOUT (3) VIN - VOUT Dropout Voltage IL = 150 mA 38 45 55 IL = 1.5 A 380 450 550 IL = 150 mA 4 9 10 IL = 1.5 A 5 14 15 25 75 (4) IGND Ground Pin Current In Normal Operation Mode IGND Ground Pin Current In Shutdown Mode (5) VSD 0.2V 15 IO(PK) Peak Output Current See (6) 2.5 mV mA A 2.0 1.7 A SHORT CIRCUIT PROTECTION ISC Short Circuit Current 4.5 A OVER TEMPERATURE PROTECTION Tsh(t) Shutdown Threshold 165 C Tsh(h) Thermal Shutdown Hysteresis 10 C SHUTDOWN INPUT (1) (2) (3) (4) (5) (6) VSDT Shutdown Threshold TdOFF Turn-off delay Output = High VIN Output = Low 0 IL = 1.5 A 20 VIN-0.3 0.2 V s Typical numbers are at 25C and represent the most likely parametric norm. Limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate TI's Average Outgoing Quality Level (AOQL). Output voltage line regulation is defined as the change in output voltage from the nominal value due to change in the input line voltage. Output voltage load regulation is defined as the change in output voltage from the nominal value due to change in load current. The line and load regulation specification contains only the typical number. However, the limits for line and load regulation are included in the output voltage tolerance specification. Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value. Dropout voltage specification applies only to output voltages of 2.5V and above. For output voltages below 2.5V, the drop-out voltage is nothing but the input to output differential, since the minimum input voltage is 2.5V. This specification has been tested for -40C TJ 85C since the temperature rise of the device is negligible under shutdown conditions. At elevated temperatures, devices must be derated based on package thermal resistance. The devices in TO-220 package must be derated at jA = 50C/W (with 0.5in2, 1oz. copper area), junction-to-ambient (with no heat sink). The devices in the SFM/TO-263 surface-mount package must be derated at jA = 60C/W (with 0.5in2, 1oz. copper area), junction-to-ambient. The devices in SOT-223 package must be derated at jA = 90C/W (with 0.5in2, 1oz. copper area), junction-to-ambient. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 5 LP3962, LP3965 SNVS066H - MAY 2000 - REVISED APRIL 2013 www.ti.com Electrical Characteristics LP3962/LP3965 (continued) Limits in standard typeface are for TJ = 25C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = VO(NOM) + 1V, IL = 10 mA, COUT = 33F, VSD = VIN-0.3V. Symbol Parameter Conditions Typ (1) LP3962/5 Min TdON ISD (2) Units Max Turn-on delay IL = 1.5 A 25 s SD Input Current VSD = VIN 1 nA ERROR FLAG COMPARATOR VT Threshold See (7) (7) VTH Threshold Hysteresis See VEF(Sat) Error Flag Saturation Isink = 100A 10 5 5 2 0.02 16 % 8 % 0.1 V Td Flag Reset Delay 1 s Ilk Error Flag Pin Leakage Current 1 nA VError = 0.5V (over temp.) 1 mA VIN = VOUT + 1.5V COUT = 100uF VOUT = 3.3V 60 VIN = VOUT + 0.3V COUT = 100uF VOUT = 3.3V 40 Imax Error Flag Pin Sink Current AC PARAMETERS PSRR n(l/f en (7) 6 Ripple Rejection Output Noise Density Output Noise Voltage (rms) f = 120Hz 0.8 BW = 10Hz - 100kHz 150 BW = 300Hz - 300kHz 100 dB V V (rms) Error Flag threshold and hysteresis are specified as percentage of regulated output voltage. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 LP3962, LP3965 www.ti.com SNVS066H - MAY 2000 - REVISED APRIL 2013 Typical Performance Characteristics Unless otherwise specified, VIN =VO(NOM) + 1V, VOUT= 2.5V, COUT = 33F, IOUT = 10mA, CIN = 68F, VSD = VIN, and TA = 25C. Drop-Out Voltage vs Temperature for Different Load Currents Drop-Out Voltage vs Temperature for Different Output Voltages (IOUT = 800mA Figure 4. Figure 5. Ground Pin Current vs Input Voltage (VSD=VIN) Ground Pin Current vs Input Voltage (VSD=100mV) Figure 6. Figure 7. Ground Current vs Temperature (VSD=VIN) Ground Current vs Temperature (VSD=0V Figure 8. Figure 9. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 7 LP3962, LP3965 SNVS066H - MAY 2000 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) Unless otherwise specified, VIN =VO(NOM) + 1V, VOUT= 2.5V, COUT = 33F, IOUT = 10mA, CIN = 68F, VSD = VIN, and TA = 25C. 8 Ground Pin Current vs Shutdown Pin Voltage Input Voltage vs Output Voltage Figure 10. Figure 11. Output Noise Density, VOUT= 2.5V Output Noise Density, VOUT= 5V Figure 12. Figure 13. Load Transient Response Ripple Rejection vs Frequency Figure 14. Figure 15. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 LP3962, LP3965 www.ti.com SNVS066H - MAY 2000 - REVISED APRIL 2013 Typical Performance Characteristics (continued) Unless otherwise specified, VIN =VO(NOM) + 1V, VOUT= 2.5V, COUT = 33F, IOUT = 10mA, CIN = 68F, VSD = VIN, and TA = 25C. VOUT vs Temperature Noise Density VIN = 3.5V, VOUT = 2.5V, IL = 10 mA Figure 16. Figure 17. Line Transient Response Line Transient Response Figure 18. Figure 19. Line Transient Response (IOUT = 1.5A) Line Transient Response (IOUT = 1.5A) Figure 20. Figure 21. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 9 LP3962, LP3965 SNVS066H - MAY 2000 - REVISED APRIL 2013 www.ti.com APPLICATIONS INFORMATION EXTERNAL CAPACITORS Like any low-dropout regulator, external capacitors are required to assure stability. these capacitors must be correctly selected for proper performance. INPUT CAPACITOR: The LP3962/5 requires a low source impedance to maintain regulator stability because the internal bias circuitry is connected directly to VIN. The input capacitor must be located less than 1 cm from the LP3962/5 device and connected directly to the input and ground pins using traces which have no other currents flowing through them (see PCB LAYOUT). The minimum allowable input capacitance for a given application depends on the type of the capacitor and ESR (equivalent series resistance). A lower ESR capacitor allows the use of less capacitance, while higher ESR types (like aluminum electrolytics) require more capacitance. The lowest value of input capacitance that can be used for stable full-load operation is 68 F (assuming it is a ceramic or low-ESR Tantalum with ESR less than 100 m). To determine the minimum input capacitance amount and ESR value, an approximation which should be used is: CIN ESR (m) / CIN (F) 1.5 This shows that input capacitors with higher ESR values can be used if sufficient total capacitance is provided. Capacitor types (aluminum, ceramic, and tantalum) can be mixed in parallel, but the total equivalent input capacitance/ESR must be defined as above to assure stable operation. IMPORTANT: The input capacitor must maintain its ESR and capacitance in the "stable range" over the entire temperature range of the application to assure stability (see CAPACITOR CHARACTERISTICS). OUTPUT CAPACITOR: An output capacitor is also required for loop stability. It must be located less than 1 cm from the LP3962/5 device and connected directly to the output and ground pins using traces which have no other currents flowing through them (see PCB LAYOUT). The minimum value of the output capacitance that can be used for stable full-load operation is 33 F, but it may be increased without limit. The output capacitor's ESR is critical because it forms a zero to provide phase lead which is required for loop stability. The ESR must fall within the specified range: 0.2 COUT ESR 5 The lower limit of 200 m means that ceramic capacitors are not suitable for use as LP3962/5 output capacitors (but can be used on the input). Some ceramic capacitance can be used on the output if the total equivalent ESR is in the stable range: when using a 100 F Tantalum as the output capacitor, approximately 3 F of ceramic capacitance can be applied before stability becomes marginal. IMPORTANT: The output capacitor must meet the requirements for minimum amount of capacitance and also have an appropriate ESR value over the full temperature range of the application to assure stability (see CAPACITOR CHARACTERISTICS). SELECTING A CAPACITOR It is important to note that capacitance tolerance and variation with temperature must be taken into consideration when selecting a capacitor so that the minimum required amount of capacitance is provided over the full operating temperature range. In general, a good Tantalum capacitor will show very little capacitance variation with temperature, but a ceramic may not be as good (depending on dielectric type). Aluminum electrolytics also typically have large temperature variation of capacitance value. Equally important to consider is a capacitor's ESR change with temperature: this is not an issue with ceramics, as their ESR is extremely low. However, it is very important in Tantalum and aluminum electrolytic capacitors. Both show increasing ESR at colder temperatures, but the increase in aluminum electrolytic capacitors is so severe they may not be feasible for some applications (see CAPACITOR CHARACTERISTICS). 10 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 LP3962, LP3965 www.ti.com SNVS066H - MAY 2000 - REVISED APRIL 2013 CAPACITOR CHARACTERISTICS CERAMIC: For values of capacitance in the 10 to 100 F range, ceramics are usually larger and more costly than tantalums but give superior AC performance for bypassing high frequency noise because of very low ESR (typically less than 10 m). However, some dielectric types do not have good capacitance characteristics as a function of voltage and temperature. Z5U and Y5V dielectric ceramics have capacitance that drops severely with applied voltage. A typical Z5U or Y5V capacitor can lose 60% of its rated capacitance with half of the rated voltage applied to it. The Z5U and Y5V also exhibit a severe temperature effect, losing more than 50% of nominal capacitance at high and low limits of the temperature range. X7R and X5R dielectric ceramic capacitors are strongly recommended if ceramics are used, as they typically maintain a capacitance range within 20% of nominal over full operating ratings of temperature and voltage. Of course, they are typically larger and more costly than Z5U/Y5U types for a given voltage and capacitance. TANTALUM: Solid Tantalum capacitors are recommended for use on the output because their typical ESR is very close to the ideal value required for loop compensation. They also work well as input capacitors if selected to meet the ESR requirements previously listed. Tantalums also have good temperature stability: a good quality Tantalum will typically show a capacitance value that varies less than 10-15% across the full temperature range of 125C to -40C. ESR will vary only about 2X going from the high to low temperature limits. The increasing ESR at lower temperatures can cause oscillations when marginal quality capacitors are used (if the ESR of the capacitor is near the upper limit of the stability range at room temperature). ALUMINUM: This capacitor type offers the most capacitance for the money. The disadvantages are that they are larger in physical size, not widely available in surface mount, and have poor AC performance (especially at higher frequencies) due to higher ESR and ESL. Compared by size, the ESR of an aluminum electrolytic is higher than either Tantalum or ceramic, and it also varies greatly with temperature. A typical aluminum electrolytic can exhibit an ESR increase of as much as 50X when going from 25C down to -40C. It should also be noted that many aluminum electrolytics only specify impedance at a frequency of 120 Hz, which indicates they have poor high frequency performance. Only aluminum electrolytics that have an impedance specified at a higher frequency (between 20 kHz and 100 kHz) should be used for the LP396X. Derating must be applied to the manufacturer's ESR specification, since it is typically only valid at room temperature. Any applications using aluminum electrolytics should be thoroughly tested at the lowest ambient operating temperature where ESR is maximum. PCB LAYOUT Good PC layout practices must be used or instability can be induced because of ground loops and voltage drops. The input and output capacitors must be directly connected to the input, output, and ground pins of the LP3962/5 using traces which do not have other currents flowing in them Kelvin connect). The best way to do this is to lay out CIN and COUT near the device with short traces to the VIN, VOUT, and ground pins. The regulator ground pin should be connected to the external circuit ground so that the regulator and its capacitors have a "single point ground". It should be noted that stability problems have been seen in applications where "vias" to an internal ground plane were used at the ground points of the LP3962/5 IC and the input and output capacitors. This was caused by varying ground potentials at these nodes resulting from current flowing through the ground plane. Using a single point ground technique for the regulator and it's capacitors fixed the problem. Since high current flows through the traces going into VIN and coming from VOUT, Kelvin connect the capacitor leads to these pins so there is no voltage drop in series with the input and output capacitors. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 11 LP3962, LP3965 SNVS066H - MAY 2000 - REVISED APRIL 2013 www.ti.com RFI/EMI SUSCEPTIBILITY RFI (radio frequency interference) and EMI (electromagnetic interference) can degrade any integrated circuit's performance because of the small dimensions of the geometries inside the device. In applications where circuit sources are present which generate signals with significant high frequency energy content (> 1 MHz), care must be taken to ensure that this does not affect the IC regulator. If RFI/EMI noise is present on the input side of the LP396X regulator (such as applications where the input source comes from the output of a switching regulator), good ceramic bypass capacitors must be used at the input pin of the LP396X. If a load is connected to the LP396X output which switches at high speed (such as a clock), the high-frequency current pulses required by the load must be supplied by the capacitors on the LP396X output. Since the bandwidth of the regulator loop is less than 100 kHz, the control circuitry cannot respond to load changes above that frequency. The means the effective output impedance of the LP396X at frequencies above 100 kHz is determined only by the output capacitor(s). In applications where the load is switching at high speed, the output of the LP396X may need RF isolation from the load. It is recommended that some inductance be placed between the LP396X output capacitor and the load, and good RF bypass capacitors be placed directly across the load. PCB layout is also critical in high noise environments, since RFI/EMI is easily radiated directly into PC traces. Noisy circuitry should be isolated from "clean" circuits where possible, and grounded through a separate path. At MHz frequencies, ground planes begin to look inductive and RFI/EMI can cause ground bounce across the ground plane. In multi-layer PCB applications, care should be taken in layout so that noisy power and ground planes do not radiate directly into adjacent layers which carry analog power and ground. OUTPUT ADJUSTMENT An adjustable output device has output voltage range of 1.216V to 5.1V. To obtain a desired output voltage, can be used with R1 always a 10k resistor. For output stability, CF must be between 68pF and 100pF. TURN-ON CHARACTERISTICS FOR OUTPUT VOLTAGES PROGRAMMED TO 2.0V OR BELOW As Vin increases during start-up, the regulator output will track the input until Vin reaches the minimum operating voltage (typically about 2.2V). For output voltages programmed to 2.0V or below, the regulator output may momentarily exceed its programmed output voltage during start up. Outputs programmed to voltages above 2.0V are not affected by this behavior. OUTPUT NOISE Noise is specified in two waysSpot Noise or Output noise density is the RMS sum of all noise sources, measured at the regulator output, at a specific frequency (measured with a 1Hz bandwidth). This type of noise is usually plotted on a curve as a function of frequency. Total output Noise or Broad-band noise is the RMS sum of spot noise over a specified bandwidth, usually several decades of frequencies. Attention should be paid to the units of measurement. Spot noise is measured in units V/Hz or nV/Hz and total output noise is measured in V(rms). 12 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 LP3962, LP3965 www.ti.com SNVS066H - MAY 2000 - REVISED APRIL 2013 The primary source of noise in low-dropout regulators is the internal reference. In CMOS regulators, noise has a low frequency component and a high frequency component, which depend strongly on the silicon area and quiescent current. Noise can be reduced in two ways: by increasing the transistor area or by increasing the current drawn by the internal reference. Increasing the area will decrease the chance of fitting the die into a smaller package. Increasing the current drawn by the internal reference increases the total supply current (ground pin current). Using an optimized trade-off of ground pin current and die size, LP3962/LP3965 achieves low noise performance and low quiescent current operation. The total output noise specification for LP3962/LP3965 is presented in the Electrical Characteristics table. The Output noise density at different frequencies is represented by a curve under typical performance characteristics. SHORT-CIRCUIT PROTECTION The LP3962and LP3965 is short circuit protected and in the event of a peak over-current condition, the shortcircuit control loop will rapidly drive the output PMOS pass element off. Once the power pass element shuts down, the control loop will rapidly cycle the output on and off until the average power dissipation causes the thermal shutdown circuit to respond to servo the on/off cycling to a lower frequency. Please refer to the section on thermal information for power dissipation calculations. ERROR FLAG OPERATION The LP3962/LP3965 produces a logic low signal at the Error Flag pin when the output drops out of regulation due to low input voltage, current limiting, or thermal limiting. This flag has a built in hysteresis. The timing diagram in Figure 22 shows the relationship between the ERROR and the output voltage. In this example, the input voltage is changed to demonstrate the functionality of the Error Flag. The internal Error flag comparator has an open drain output stage. Hence, the ERROR pin should be pulled high through a pull up resistor. Although the ERROR pin can sink current of 1mA, this current is energy drain from the input supply. Hence, the value of the pull up resistor should be in the range of 10k to 1M. The ERROR pin must be connected to ground if this function is not used. It should also be noted that when the shutdown pin is pulled low, the ERROR pin is forced to be invalid for reasons of saving power in shutdown mode. Figure 22. Error Flag Operation Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 13 LP3962, LP3965 SNVS066H - MAY 2000 - REVISED APRIL 2013 www.ti.com SENSE PIN In applications where the regulator output is not very close to the load, LP3965 can provide better remote load regulation using the SENSE pin. Figure 23 depicts the advantage of the SENSE option. LP3962 regulates the voltage at the output pin. Hence, the voltage at the remote load will be the regulator output voltage minus the drop across the trace resistance. For example, in the case of a 3.3V output, if the trace resistance is 100m, the voltage at the remote load will be 3.15V with 1.5 A of load current, ILOAD. The LP3965 regulates the voltage at the sense pin. Connecting the sense pin to the remote load will provide regulation at the remote load, as shown in Figure 23. If the sense option pin is not required, the sense pin must be connected to the VOUT pin. Figure 23. Improving remote load regulation using LP3965 SHUTDOWN OPERATION A CMOS Logic level signal at the shutdown ( SD) pin will turn-off the regulator. Pin SD must be actively terminated through a 10k pull-up resistor for a proper operation. If this pin is driven from a source that actively pulls high and low (such as a CMOS rail to rail comparator), the pull-up resistor is not required. This pin must be tied to Vin if not used. DROPOUT VOLTAGE The dropout voltage of a regulator is defined as the minimum input-to-output differential required to stay within 2% of the output voltage. The LP3962/LP3965 use an internal MOSFET with an Rds(on) of 240m (typically). For CMOS LDOs, the dropout voltage is the product of the load current and the Rds(on) of the internal MOSFET. REVERSE CURRENT PATH The internal MOSFET in LP3962and LP3965 has an inherent parasitic diode. During normal operation, the input voltage is higher than the output voltage and the parasitic diode is reverse biased. However, if the output is pulled above the input in an application, then current flows from the output to the input as the parasitic diode gets forward biased. The output can be pulled above the input as long as the current in the parasitic diode is limited to 200mA continuous and 1A peak. MAXIMUM OUTPUT CURRENT CAPABILITY LP3962 and LP3965 can deliver a continuous current of 1.5 A over the full operating temperature range. A heatsink may be required depending on the maximum power dissipation and maximum ambient temperature of the application. Under all possible conditions, the junction temperature must be within the range specified under operating conditions. The total power dissipation of the device is given by: PD = (VIN-VOUT)IOUT+ (VIN)IGND 14 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 LP3962, LP3965 www.ti.com SNVS066H - MAY 2000 - REVISED APRIL 2013 where IGND is the operating ground current of the device (specified under Electrical Characteristics). The maximum allowable temperature rise (TRmax) depends on the maximum ambient temperature (TAmax) of the application, and the maximum allowable junction temperature(TJmax): TRmax = TJmax- TAmax The maximum allowable value for junction to ambient Thermal Resistance, JA, can be calculated using the formula: JA = TRmax / PD LP3962 and LP3965 are available in TO-220, SFM/TO-263, and SOT-223 packages. The thermal resistance depends on amount of copper area or heat sink, and on air flow. If the maximum allowable value of JA calculated above is 60 C/W for TO-220 package, 60 C/W for SFM/TO-263 package, and 140 C/W for SOT-223 package, no heatsink is needed since the package can dissipate enough heat to satisfy these requirements. If the value for allowable JA falls below these limits, a heat sink is required. HEATSINKING TO-220 PACKAGES The thermal resistance of a TO-220 package can be reduced by attaching it to a heat sink or a copper plane on a PC board. If a copper plane is to be used, the values of JA will be same as shown in next section for SFM/TO263 package. The heatsink to be used in the application should have a heatsink to ambient thermal resistance, HA JA - CH - JC. In this equation, CH is the thermal resistance from the junction to the surface of the heat sink and JC is the thermal resistance from the junction to the surface of the case. JC is about 3C/W for a TO-220 package. The value for CH depends on method of attachment, insulator, etc. CH varies between 1.5C/W to 2.5C/W. If the exact value is unknown, 2C/W can be assumed. HEATSINKING SFM/TO-263 AND SOT-223 PACKAGES The SFM/TO-263 and SOT-223 packages use the copper plane on the PCB as a heatsink. The tab of these packages are soldered to the copper plane for heat sinking. Figure 24 shows a curve for the JA of SFM/TO-263 package for different copper area sizes, using a typical PCB with 1 ounce copper and no solder mask over the copper area for heat sinking. Figure 24. JA vs Copper(1 Ounce) Area for SFM/TO-263 package As shown in the figure, increasing the copper area beyond 1 square inch produces very little improvement. The minimum value for JA for the SFM/TO-263 packag mounted to a PCB is 32C/W. Figure 25 shows the maximum allowable power dissipation for SFM/TO-263 packages for different ambient temperatures, assuming JA is 35C/W and the maximum junction temperature is 125C. Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 15 LP3962, LP3965 SNVS066H - MAY 2000 - REVISED APRIL 2013 www.ti.com Figure 25. Maximum power dissipation vs ambient temperature for SFM/TO-263 package Figure 26 shows a curve for the JA of SOT-223 package for different copper area sizes, using a typical PCB with 1 ounce copper and no solder mask over the copper area for heat sinking. Figure 26. JA vs Copper(1 Ounce) Area for SOT-223 package Figure 27 through Figure 35 show different layout scenarios for SOT-223 package. Figure 27. SCENARIO A, JA = 148C/W Figure 28. SCENARIO B, JA = 125C/W 16 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 LP3962, LP3965 www.ti.com SNVS066H - MAY 2000 - REVISED APRIL 2013 Figure 29. SCENARIO C, JA = 92C/W Figure 30. SCENARIO D, JA = 83C/W Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 17 LP3962, LP3965 SNVS066H - MAY 2000 - REVISED APRIL 2013 www.ti.com Figure 31. SCENARIO E, JA = 77C/W Figure 32. SCENARIO F, JA = 75C/W 18 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 LP3962, LP3965 www.ti.com SNVS066H - MAY 2000 - REVISED APRIL 2013 Figure 33. SCENARIO G, JA = 113C/W Figure 34. SCENARIO H, JA = 79C/W Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 19 LP3962, LP3965 SNVS066H - MAY 2000 - REVISED APRIL 2013 www.ti.com Figure 35. SCENARIO I, JA = 78.5C/W 20 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 LP3962, LP3965 www.ti.com SNVS066H - MAY 2000 - REVISED APRIL 2013 REVISION HISTORY Changes from Revision G (April 2013) to Revision H * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 20 Submit Documentation Feedback Copyright (c) 2000-2013, Texas Instruments Incorporated Product Folder Links: LP3962 LP3965 21 PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LP3962EMP-1.8 NRND SOT-223 NDC 5 1000 TBD Call TI Call TI -40 to 125 LBCB LP3962EMP-1.8/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LBCB LP3962EMP-2.5 NRND SOT-223 NDC 5 1000 TBD Call TI Call TI -40 to 125 LBDB LP3962EMP-2.5/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LBDB LP3962EMP-3.3 NRND SOT-223 NDC 5 1000 TBD Call TI Call TI -40 to 125 LBEB LP3962EMP-3.3/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LBEB LP3962EMPX-2.5/NOPB ACTIVE SOT-223 NDC 5 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LBDB LP3962ES-1.8 NRND DDPAK/ TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LP3962ES -1.8 LP3962ES-1.8/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3962ES -1.8 LP3962ES-2.5 NRND DDPAK/ TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LP3962ES -2.5 LP3962ES-2.5/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3962ES -2.5 LP3962ES-3.3 NRND DDPAK/ TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LP3962ES -3.3 LP3962ES-3.3/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3962ES -3.3 LP3962ESX-1.8/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3962ES -1.8 LP3962ESX-2.5/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3962ES -2.5 LP3962ESX-3.3/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3962ES -3.3 LP3962ESX-5.0/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3962ES -5.0 LP3962ET-3.3/LB05 NRND TO-220 NEB 5 45 TBD Call TI Call TI Addendum-Page 1 LP3962ET -3.3 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 14-Oct-2017 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LP3962ET-3.3/NOPB ACTIVE TO-220 NDH 5 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LP3962ET -3.3 LP3965EMP-1.8/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LBKB LP3965EMP-2.5/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LBLB LP3965EMP-3.3 NRND SOT-223 NDC 5 1000 TBD Call TI Call TI -40 to 125 LBNB LP3965EMP-3.3/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LBNB LP3965EMP-ADJ NRND SOT-223 NDC 5 1000 TBD Call TI Call TI -40 to 125 LBRB LP3965EMP-ADJ/NOPB ACTIVE SOT-223 NDC 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LBRB LP3965EMPX-ADJ/NOPB ACTIVE SOT-223 NDC 5 2000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LBRB LP3965ES-1.8 NRND DDPAK/ TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LP3965ES -1.8 LP3965ES-1.8/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3965ES -1.8 LP3965ES-2.5 NRND DDPAK/ TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LP3965ES -2.5 LP3965ES-2.5/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3965ES -2.5 LP3965ES-3.3 NRND DDPAK/ TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LP3965ES -3.3 LP3965ES-3.3/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3965ES -3.3 LP3965ES-ADJ NRND DDPAK/ TO-263 KTT 5 45 TBD Call TI Call TI -40 to 125 LP3965ES -ADJ LP3965ES-ADJ/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3965ES -ADJ LP3965ESX-1.8/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3965ES -1.8 LP3965ESX-2.5/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3965ES -2.5 LP3965ESX-3.3 NRND DDPAK/ TO-263 KTT 5 500 TBD Call TI Call TI -40 to 125 LP3965ES -3.3 Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 14-Oct-2017 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LP3965ESX-3.3/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3965ES -3.3 LP3965ESX-ADJ/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3965ES -ADJ LP3965ET-1.8/NOPB ACTIVE TO-220 NDH 5 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LP3965ET -1.8 LP3965ET-3.3/NOPB ACTIVE TO-220 NDH 5 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LP3965ET -3.3 LP3965ET-ADJ NRND TO-220 NDH 5 45 TBD Call TI Call TI -40 to 125 LP3965ET -ADJ LP3965ET-ADJ/NOPB ACTIVE TO-220 NDH 5 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LP3965ET -ADJ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 3 Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Oct-2017 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 4 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LP3962EMP-1.8 SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP3962EMP-1.8/NOPB SOT-223 NDC 5 1000 330.0 LP3962EMP-2.5 SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 16.4 7.0 7.5 2.2 12.0 16.0 LP3962EMP-2.5/NOPB SOT-223 NDC 5 1000 Q3 330.0 16.4 7.0 7.5 2.2 12.0 16.0 LP3962EMP-3.3 SOT-223 NDC 5 Q3 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP3962EMP-3.3/NOPB SOT-223 NDC LP3962EMPX-2.5/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 5 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP3962ESX-1.8/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LP3962ESX-2.5/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LP3962ESX-3.3/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LP3962ESX-5.0/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LP3965EMP-1.8/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP3965EMP-2.5/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP3965EMP-3.3 SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP3965EMP-3.3/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 Device LP3965EMP-ADJ Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP3965EMP-ADJ/NOPB SOT-223 NDC 5 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP3965EMPX-ADJ/NOPB SOT-223 NDC 5 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3 LP3965ESX-1.8/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LP3965ESX-2.5/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LP3965ESX-3.3 DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LP3965ESX-3.3/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LP3965ESX-ADJ/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP3962EMP-1.8 SOT-223 NDC 5 1000 367.0 367.0 35.0 LP3962EMP-1.8/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0 LP3962EMP-2.5 SOT-223 NDC 5 1000 367.0 367.0 35.0 LP3962EMP-2.5/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0 LP3962EMP-3.3 SOT-223 NDC 5 1000 367.0 367.0 35.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP3962EMP-3.3/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0 LP3962EMPX-2.5/NOPB SOT-223 NDC 5 2000 367.0 367.0 35.0 LP3962ESX-1.8/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 LP3962ESX-2.5/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 LP3962ESX-3.3/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 LP3962ESX-5.0/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 LP3965EMP-1.8/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0 LP3965EMP-2.5/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0 LP3965EMP-3.3 SOT-223 NDC 5 1000 367.0 367.0 35.0 LP3965EMP-3.3/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0 LP3965EMP-ADJ SOT-223 NDC 5 1000 367.0 367.0 35.0 LP3965EMP-ADJ/NOPB SOT-223 NDC 5 1000 367.0 367.0 35.0 LP3965EMPX-ADJ/NOPB SOT-223 NDC 5 2000 367.0 367.0 35.0 LP3965ESX-1.8/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 LP3965ESX-2.5/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 LP3965ESX-3.3 DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 LP3965ESX-3.3/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 LP3965ESX-ADJ/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 Pack Materials-Page 3 MECHANICAL DATA NDC0005A www.ti.com MECHANICAL DATA NDH0005D www.ti.com MECHANICAL DATA KTT0005B TS5B (Rev D) BOTTOM SIDE OF PACKAGE www.ti.com MECHANICAL DATA NEB0005F www.ti.com MECHANICAL DATA NEB0005B www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LP3962EMP-1.8 LP3962EMP-1.8/NOPB LP3962EMP-2.5 LP3962EMP-2.5/NOPB LP3962EMP-3.3 LP3962EMP3.3/NOPB LP3962EMPX-1.8 LP3962EMPX-1.8/NOPB LP3962EMPX-2.5 LP3962EMPX-2.5/NOPB LP3962ES-1.8 LP3962ES-1.8/NOPB LP3962ES-2.5 LP3962ES-2.5/NOPB LP3962ES-3.3 LP3962ES-3.3/NOPB LP3962ESX-1.8 LP3962ESX-1.8/NOPB LP3962ESX-2.5 LP3962ESX-2.5/NOPB LP3962ESX-3.3 LP3962ESX-3.3/NOPB LP3962ESX-5.0 LP3962ESX-5.0/NOPB LP3962ET-3.3 LP3962ET-3.3/LB05 LP3962ET-3.3/NOPB