185682J100RAC-F - Cornell Dubilier Electronics, Inc.

Type 168/185 Metallized Polyester Radial Lead Capacitors

CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com

Speciﬁcations

Radial Box Metallized Polyester Capacitors for Automatic Insertion

Highlights

Case and epoxy ﬁll meets UL94V-0

5.0 mm (0.197") lead spacing

Bulk, tape and reel or ammo pack

Non-inductively wound

Non-polar

Low leakage

Lead material: Tinned copper wire

•

Capacitance Range:

Voltage Range:

Capacitance Tolerance:

Operating Temperature Range:

Dielectric Withstand Voltage:

Dissipation Factor (DF):

0.001 µF to 1.0 µF

50 Vdc to 400 Vdc (30 Vac to 200 Vac, 60 Hz)

±5%, ±10%, ±20%

–55 ºC to +125 ºC (with 50% Vdc derating >85 ºC)

1.6 x rated voltage for 2 sec @ +25 ºC ±5 ºC

tanδ x 10 –4 at 25 ºC ±5 ºC

The Type 168/185 series radial lead metallized polyester

box capacitors are available in bulk (Type 168) or on

ammo pack or tape and reel (Type 185). These capacitors

are constructed in rugged rectangular plastic cases and

all come with 5.0 mm (0.197") lead spacing. They are

good for general purpose applications such as bypass,

decoupling, energy storage/discharge and arc suppres-

sion.

Total Self Inductance (L):

Maximum Pulse Rise Time (dv/dt):

Long Term Stability (after two years):Capacitance change ∆C/C ≤ ±3% under stan-

dard environmental conditions

If the working voltage (V) is less than the nominal voltage

(Vn), the capacitor can work at higher dv/dt. In this case, the

maximum value allowed is obtained by multiplying the above

value with the ratio Vn/V.

Approximately 7 nH

kHz C ≤0.1 µF C > 0.1 µF

1≤100 ≤100

10 ≤150 ≤150

100 ≤300

Vn V/µs

50 250

63 250

100 300

250 400

400 600

RoHS Compliant

CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com

Type 168/185 Metallized Polyester Radial Lead Capacitors

Capacitor Outline Drawing

Ratings

Test Method and Performance

Max

±.015

(±0.4 mm)

.217 ±.039

(5.5 ±1.0 mm)

* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%

# Indicates packaging type: R = Tape and Reel, A = Ammo Pack

> Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping speciﬁcations)

Lead length shown is as supplied on the 168 Series

Catalog Tape & Reel Cap Inches Millimeters

Part Number Ammo Pack (µF) L T H S Ød L T H S Ød

50 Vdc / 30 Vac

168104*50A-F 185104*50#A>-F 0.10 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168154*50A-F 185154*50#A>-F 0.15 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168224*50C-F 185224*50#C>-F 0.22 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5

168334*50C-F 185334*50#C>-F 0.33 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168474*50H-F 185474*50#H>-F 0.47 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168684*50F-F 185684*50#F>-F 0.68 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6

168824*50G-F 185824*50#G>-F 0.82 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6

168105*50G-F 185105*50#G>-F 1.00 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6

63 Vdc / 40 Vac

168473*63A-F 185473*63#A>-F 0.047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168563*63A-F 185563*63#A>-F 0.056 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168683*63A-F 185683*63#A>-F 0.068 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168823*63A-F 185823*63#A>-F 0.082 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168104*63A-F 185104*63#A>-F 0.10 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168154*63C-F 185154*63#C>-F 0.15 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5

168184*63C-F 185184*63#C>-F 0.18 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5

168224*63C-F 185224*63#C>-F 0.22 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5

168274*63C-F 185274*63#C>-F 0.27 0.283 0.098 0.255 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168334*63H-F 185334*63#H>-F 0.33 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168474*63H-F 185474*63#H>-F 0.47 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168684*63F-F 185684*63#F>-F 0.68 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6

168105*63G-F 185105*63#G>-F 1.00 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6

Insulation Resistance

Test Conditions

Temperature: 25 ºC ±5 ºC

Voltage Charge Time: 1 minute

Voltage Charge: 10 Vdc for Vn < 100 Vdc

100 Vdc for Vn ≥ 100 Vdc

Performance

For Vn > 100 Vdc: C ≤ 0.33 µF, ≥15,000 MΩ

C > 0.33 µF, ≥ 5,000 S

For Vn ≤100 Vdc: C ≤ 0.33 µF, 30,000 MΩ

C > 0.33 µF, ≥ 10,000 S

Damp Heat Test

Test Conditions

Temperature: +40 ºC

Relative Humidity: 95%

Test Duration: 21 days

Performance

Capacitance Change ∆C/C: ±5%

DF Change ∆tgδ: ≤ 0.005 (10 KHz)

Insulation Resistance: ≥ 50% of limit value

Life Test

Test Conditions REF

Temperature: +85 ºC

Test Duration: 2000 hrs

Voltage Applied: 1.25 x Vn

Performance

Capacitance Change ∆C/C: ≤ ±2%

DF Change ∆tgδ: ≤30 x 10–4 at 10 kHz

Insulation Resistance: ≥ 50% of limit value

Soldering

Test Conditions

Soldering Temperature:260 ºC ±5 ºC

Soldering Duration:10 sec ±1 sec

Performance

Capacitance Change

∆C/C:≤ ±2%

DF Change ∆tgδ:≤30 x 10–4 at 10 kHz

Insulation Resistance:≥ limit value

RoHS

Compliant

Type 168/185 Metallized Polyester Radial Lead Capacitors

CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com

* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%

# Indicates packaging type: R = Tape and Reel, A = Ammo Pack

> Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping speciﬁcation)

Catalog Tape & Reel Cap Inches Millimeters

Part Number Ammo Pack (µF) L T H S Ød L T H S Ød

100 Vdc / 63 Vac

168102*100A-F 185102*100#A>-F 0.0010 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168152*100A-F 185152*100#A>-F 0.0015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168222*100A-F 185222*100#A>-F 0.0022 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168272*100A-F 185272*100#A>-F 0.0027 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168332*100A-F 185332*100#A>-F 0.0033 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168392*100A-F 185392*100#A>-F 0.0039 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168472*100A-F 185472*100#A>-F 0.0047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168562*100A-F 185562*100#A>-F 0.0056 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168682*100A-F 185682*100#A>-F 0.0068 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168822*100A-F 185822*100#A>-F 0.0082 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168103*100A-F 185103*100#A>-F 0.010 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168153*100A-F 185153*100#A>-F 0.015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168183*100A-F 185183*100#A>-F 0.018 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168223*100A-F 185223*100#A>-F 0.022 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168273*100A-F 185273*100#A>-F 0.027 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168333*100C-F 185333*100#C>-F 0.033 0.283 0.098 0.295 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168393*100C-F 185393*100#C>-F 0.039 0.283 0.098 0.295 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168473*100C-F 185473*100#C>-F 0.047 0.283 0.098 0.295 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168683*100H-F 185683*100#H>-F 0.068 0.283 0.098 0.335 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168104*100H-F 185104*100#H>-F 0.10 0.283 0.098 0.335 0.197 0.020 7.2 2.5 7.5 5.0 0.5

168154*100F-F 185154*100#F>-F 0.15 0.283 0.177 0.394 0.197 0.024 7.2 4.5 9.5 5.0 0.6

168224*100G-F 185224*100#G>-F 0.22 0.283 0.197 0.433 0.197 0.024 7.2 5.0 10.0 5.0 0.6

250 Vdc / 160 Vac

168332*250A-F 185332*250#A>-F 0.0033 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168472*250A-F 185472*250#A>-F 0.0047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168682*250A-F 185682*250#A>-F 0.0068 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168103*250A-F 185103*250#A>-F 0.010 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168153*250A-F 185153*250#A>-F 0.015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168223*250C-F 185223*250#C>-F 0.022 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5

168333*250C-F 185333*250#C>-F 0.033 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5

168473*250F-F 185473*250#F>-F 0.047 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6

168683*250F-F 185683*250#F>-F 0.068 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6

168104*250G-F 185104*250#G>-F 0.100 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10 5.0 0.6

400 Vdc / 200 Vac

168102*400A-F 185102*400#A>-F 0.001 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168152*400A-F 185152*400#A>-F 0.0015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168222*400A-F 185222*400#A>-F 0.0022 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168332*400C-F 185332*400#C>-F 0.0033 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168472*400C-F 185472*400#C>-F 0.0047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168682*400C-F 185682*400#C>-F 0.0068 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5

168103*400F-F 185103*400#F>-F 0.010 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5

168153*400F-F 185153*400#F>-F 0.015 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6

168223*400G-F 185223*400#G>-F 0.022 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10 5.0 0.6

CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com

Type 168/185 Metallized Polyester Radial Lead Capacitors

168/185 104 K 100 R H B –F

Packaging *Tooling RoHS

Type Case Code Compliant

Series Capacitance Tolerance Voltage (#) Code (>) Designation

185 102 = .001 µF J = ±5% 50 = 50 Vdc A = Ammo A A

103 = .01 µF K = ±10% 63 = 63 Vdc R = Tape & Reel C B

104 = .1 µF M = ±20% 100 = 100 Vdc F C

105 = 1.0 µF 250 = 250 Vdc G

400 = 400 Vdc H

Tape Speciﬁcation - 5.0 mm Lead Spacing

> The H dimension depends on the

insertion equipment used. Specify

the proper tooling code as indicated

below.

Part Numbering System for Auto Insertion

* Tooling code (>) depends on the users insertion equipment requirements. See table for available options.

Tooling H Dimensions

Code Millimeters Inches

A 16.5±0.75 .679±0.030

B 18.5±0.75 .728±0.030

C 16.0±0.75 .630±0.030

Item Code Millimeters Inches

Case Quantity Quantity

Lead-to-Lead Distance P 5.0+0.6 –0.2 .197+.024 –.040 Code Reeled Ammo Pack

Feed Hole Pitch P012.7±0.3 .5±.012 A 2500 3500

Pitch of Component P112.7±1.0 .5±.039 C 1800 1500

Hole Center to Lead P23.85±0.7 .152±.028 F 1200 1200

Feed Hole Center to P36.35±1.3 .250±.051 G 1000 1000

Component Center H 1400 1400

Component Alignment, F-R ∆h 0±2.0 0±.079

Tape Width W 18+1.0 –0.1 .709+.039 –.004

Hold-down Tape Width W06.0 min .236 min

Hole Position W19.0+0.75 –0.05 .355+.030 –.001

Hold-down Tape Position W23.0 Max .118 Max

Height of Component H > >

from Tape Center

Feed Hole Diameter D04.0±0.3 .157±.012