308 Constitution Drive
Menlo Park, CA 94025-1164
Phone: 800-227-4856
www.circuitprotection.com
PolySwitch®
PTC Devices
Overcurrent Protection Devi ce
Raychem Circuit Protection Products
PRODUCT: AGRF800
DOCUMENT: SCD 25235
PCN: A95482
REV LETTER: B
REV DATE: MAY 8, 2007
PAGE NO.: 1 OF 2
Specification Status: RELEASED
Electrical Rating
Voltage: 16VDC MAX
Insulating Material:
Cured, Flame Retardant Epoxy Polymer
Lead Material:
20 AWG Tin Plated Copper
(0.8 mm [0.032] nom. diameter)
Part Marking:
Manufacturer’s Mark
and Voltage
Lot Identification
Part Identification
GF8
(can be on back)
16
TABLE I. INSTALLATION ENVELOPE DIMENSIONS:
A B C D E F G
MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX TYP MIN MAX
mm: -- 12.7 -- 22.2 4.3 5.8 7.6 -- -- 3.0 1.2 -- 5.08
in*: -- (0.50) -- (0.88) (0.17) (0.23) (0.30) -- -- (0.12) (0.05) -- (0.200)
*Rounded off approximation
TABLE II. PERFORMANCE RATINGS:
CURRENT RATINGS TIME TO
TRIP INITIAL
RESISTANCE R1 MAX
1 HR. POST TRIP
RESISTANCE
STANDARD TRIP
RA MAX
TRIPPED-
STATE
POWER
DISSIPATION
AMPS
AT 25°C SECONDS
AT 25°C, 40 A OHMS
AT 25°C OHMS
AT 25°C OHMS
AT 25°C WATTS AT
25°C
HOLD
AT
R1 MAX
HOLD
AT
RA MAX
TRIP MAX MIN MAX TYP
8.0 7.6 15.0 5.5 0.0049 0.0113 0.0175 0.0181 3.2
Reference Documents: PS400, PS300 (reference for R1 MAX)
Precedence: This specification takes precedence over documents referenced herein.
Effectivity: Reference documents shall be the issue in effect on the date of invitation for bid.
CAUTION: Operation beyond the rated voltage or current may result in rupture, electrical arcing or flame.
Materials Information
ROHS Compliant ELV Compliant Pb-Free
© 2004, 2007 Electronics Corporation. All rights reserved.
308 Constitution Drive
Menlo Park, CA 94025-1164
Phone: 800-227-4856
www.circuitprotection.com
PolySwitch®
PTC Devices
Overcurrent Protection Devi ce
Raychem Circuit Protection Products
PRODUCT: AGRF800
DOCUMENT: SCD 25235
PCN: A95482
REV LETTER: B
REV DATE: MAY 8, 2007
PAGE NO.: 2 OF 2
TABLE III. AUTOMOTIVE SPECIFIC STRESS TESTS AND TEST CONDITIONS:
ELECTRICAL STRESS TESTS
TEST CONDIT IONS (see note 2)
ESD Voltage Withstand
(see note 1) 25kV
Short Circuit Fault Current Durability 25 cycles, 16V, 200A
Fault Current Durability
350 cycles, 16V/100A
End-of-life Mode Verification
1750 cycles, 16V/100A
Jump Start Endurance
(see note 1) 3 cycles, 26V, 1 minute duration
Load Dump Endurance
(see note 1) 10 cycles, 86.5V
Note 1: The PolySwitch devices are tested in series with a load resistance and the voltages specified in the test conditions are
shared between the PolySwitch device and the load resistance as specified in PS400.
Note 2: Please refer to Appendix A of PS400 for the detailed test procedures
