Series CA2 www.vishay.com Vishay Wet Tantalum Capacitor, Button, All-Tantalum Case, - 55 C to + 125 C Operation FEATURES * * * * * All-Tantalum electrodes eliminate silver migration Withstands high ripple current Long life reliability Reverse voltage capability Instant use after long storage PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 C to + 125 C Voltage Range: 6 VDC to 125 VDC Capacitance Range: 47 F to 1800 F SPECIFICATIONS Environmental classification: 55/125/56 Vibration: 10 Hz to 2000 Hz, 0.75 mm or 98 m/s2, 15 h Bump: 390 m/s2, 4000 bumps Shock: 981 m/s2 Acceleration: 981 m/s2 Low air pressure: 1 kPa INTRODUCTION This conveniently-packaged polar button unit employs a non-solid electrolyte, and has a sintered tantalum anode. The anode is produced from a high capacitance powder resulting in a capacitor of small size and large CV product. The cathode is also of tantalum and overcomes the restrictions of a silver cathode system in allowing a high ripple current rating and application of a 3 V reverse potential. This all-tantalum construction results in a non-catastrophic wear-out mechanism. The seal is a high efficient system comprising a PTFE gasket clamped between coined plates of tantalum by a work-hardened nickel ring. This type of seal, common to all button styles, is largely responsible for their long life and high reliability and severe military environments. The CA2 series ranges are available in several termination options. These include a mounting stud and pins for circuit mounting. APPLICATIONS The CA2 series are designed for use in general military and professional applications. For example: Power supply "smoothing" filter networks, switching, by-pass, timer functions and where reverse potentials occur. WEIGHT The CA2 style with a stud termination weighs approximately 18.1 g, including the nut. The CA2 styles, which has a printed circuit board mounting, weighs approximately 17.3 g. APPROVALS These capacitors are available released to: * BS CECC 30 202 002 RIPPLE CURRENT CAPABILITY The maximum allowable ripple current is 1 ARMS up to 85 C and 750 mARMS to 125 C. These values apply under normal cooling conditions and are irrespective of frequency or waveform. The algebraic sum of the AC peak and DC voltages must not exceed the forward or reverse voltage ratings at the relevant temperature. At certain frequency/temperature/DC voltage combinations higher levels of ripple current may be used. The applications department should be contacted before the above levels are exceeded. REVERSE VOLTAGE CAPABILITY The CA2 series employ tantalum cathodes which allow the continuous application of reverse potentials not exceeding 3 V over the whole temperature range. SURGE VOLTAGE The surge voltage capability is 115 % of the voltage rating at the relevant temperature. TEMPERATURE RANGE The capacitor is designed for operation between - 55 C and + 125 C, with linear voltage derating above + 85 C to 66 % of the rated voltage at + 125 C. CAPACITANCE TOLERANCE The standard capacitance tolerance is 20 % although special tolerances are available by arrangement. Revision: 28-Oct-11 Document Number: 42078 1 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series CA2 www.vishay.com Vishay APPLICATION INFORMATION RELIABILITY Capacitors may be operated at less than the rated voltage, resulting in significantly reduced leakage current values. All capacitors are subjected to burn-in. This is to remove infant mortalities and ensure reliability. The capacitor lifetime is enhanced when the unit is subjected to a reduced ripple current, a low ambient temperature, and is externally cooled. The use of a heat sink is recommended. In timing circuits, or other applications where the device is subjected only to a DC voltage, the ballistic or DC capacitance will be somewhat larger than measured at 50 Hz. The parametric information must necessarily be brief, although additional comprehensive data is available on request, and the tests tailored to customers' requirements can be made. ORDERING PROCEDURE Example: CA2C (220 F, 50 VDC) Vishay Part Number: CA2C227M050P ORDERING INFORMATION CA2 C 227 M 100 A MODEL CASE CODE CAPACITANCE TOLERANCE VOLTAGE TERMINATION AND PACKAGING - See Ratings and Case Codes Table This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow M = 20 % (std) K = 10 % (special order) This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating. A decimal point is indicated by an "R" (6R3 = 6.3 V) A = Stud B = PC mount pins C = Twin tag or ribbon D = Panel or potting tag Blank = Standard (tin/lead coating) DIMENSIONS in millimeters The CA2 series is comprised of two case sizes, differing in depth of cup only. The case size dimensions are shown in the table. Four mounting styles are available in both case sizes. Stud C PC Pins D + Potting Tag Twin Tag or Ribbons + + + A B J E N G - H Mounting holes M dia. F 20 S.W.G. H.T.D. Nickel 4 BA shakeproof nut Hole Q dia. P This mounting style is suitable for panel thickness of up to 1.2 mm L crs. R - S Hole T dia. W U crs. Mounting holes V dia. K crs. A 3.6 B max. C D 8.5 (1) 21.8 8.4 (2) E F G H J K crs. L crs. M N dia. nom. 8.4 16.2 8.4 1.8 0.8 20.3 10.2 1.1 2.4 P Q dia. R S T dia. U crs. V W dia. nom. 13.1 1.0 7.5 10.7 1.6 13.0 3.5 0.30 Notes * All dimensions are in mm, and are maximum unless otherwise stated (1) For B case size, case height is 6.7 mm (2) Width of anode tag 4.22 mm max. Revision: 28-Oct-11 Document Number: 42078 2 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series CA2 www.vishay.com Vishay STANDARD RATINGS VISHAY CASE PART NUMBERS CODE CAPACITANCE AT 50 Hz (F) C DISSIPATION FACTOR MAX. ESR MAX. ESR MAX. DC MAX. DC AT 50 Hz AT 50 Hz AT 20 C AT - 55 C AT 20 C AT 125 C (%) (%) 100 kHz 100 kHz (A) (A) () () 20 C 125 C - 55 C 125 C 6 VDC AT 85 C; 4 VDC AT 125 C CA2C128(1)006(2) C 1200 75.0 95.0 1.0 5.0 15.0 50 - 80 25.0 5.0 10.0 50 - 75 25.0 5.0 10.0 50 - 70 20.0 5.0 8.0 50 - 65 20.0 8 VDC AT 85 C; 5.3 VDC AT 125 C CA2C108(1)008(2) C 1000 65.0 CA2C827(1)010(2) C 820 55.0 CA2C687(1)015(2) C 680 45.0 85.0 1.0 10 VDC AT 85 C; 6.6 VDC AT 125 C 70.0 1.0 15 VDC AT 85 C; 10 VDC AT 125 C 55.0 1.0 20 VDC AT 85 C; 13.4 VDC AT 125 C CA2C397(1)020(2) C 390 25.0 30.0 1.0 5.0 5.0 50 - 50 15.0 CA2C477(1)020(2) C 470 30.0 40.0 1.0 5.0 5.0 50 - 55 15.0 CA2C567(1)020(2) C 560 35.0 45.0 1.0 5.0 5.0 50 - 60 15.0 CA2C277(1)030(2) C 270 17.0 20.0 1.0 5.0 5.0 50 - 45 10.0 CA2C337(1)030(2) C 330 20.0 25.0 1.0 5.0 5.0 50 - 50 10.0 30 VDC AT 85 C; 20 VDC AT 125 C 50 VDC AT 85 C; 33.3 VDC AT 125 C CA2C157(1)050(2) C 150 9.5 12.0 1.0 5.0 3.0 50 - 30 10.0 CA2C187(1)050(2) C 180 1.5 15.0 1.0 5.0 3.0 50 - 35 10.0 CA2C227(1)050(2) C 220 14.0 18.0 1.0 5.0 3.0 50 - 40 10.0 75 VDC AT 85 C; 50 VDC AT 125 C CA2C686(1)075(2) C 68 5.0 6.5 1.0 5.0 3.0 50 - 15.0 7.5 CA2C826(1)075(2) C 82 5.5 7.0 1.0 5.0 3.0 50 - 17.5 7.5 CA2C107(1)075(2) C 100 7.0 9.0 1.0 5.0 3.0 50 - 20 7.5 CA2C127(1)075(2) C 120 7.5 10.0 1.0 5.0 3.0 50 - 25 7.5 5.0 3.0 50 - 12.5 7.5 5.0 3.0 50 - 10.0 7.5 100 VDC AT 85 C; 66.7 VDC AT 125 C CA2C566(1)100(2) C 56 3.5 4.5 1.0 125 VDC AT 85 C; 83.3 VDC AT 125 C CA2C476(1)125(2) C 47 3.0 4.0 1.0 Note * Part number definitions: (1) Capacitance tolerance: M= 20 % standard, K = 10 % special order (2) Termination type: A = Stud or bolt, B = Pins for PCB, C = Twin tags or ribbons, D = Potting tag Revision: 28-Oct-11 Document Number: 42078 3 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series CA2 www.vishay.com Vishay PERFORMANCE CURVES Dissipation factor/temperature at 50 Hz 160 1200 F, 6 V 47 F, 125 V 110 120 90 Dissipation factor (%) Percentage of capacitance ( 20 C standard) Capacitance/temperature at 50 Hz 70 1200 F, 6 V 50 30 80 40 47 F, 125 V 10 0 - 60 - 40 - 20 0 20 40 60 80 100 120 (C) - 60 Impedance/temperature at 50 Hz - 40 - 20 0 20 60 80 100 120 (C) Leakage current/temperature at maximum voltage 50 100 47 F, 125 V 1200 F, 6 V 50 120 F, 75 V 20 10 680 F, 15 V 5 3 Leakage current (A) 40 30 Impedance () 40 30 20 47 F, 125 V 10 1200 F, 6 V 2 0 1 - 60 - 40 - 20 0 20 40 60 80 - 60 100 120 (C) - 40 - 20 Capacitance/frequency at 20 C 20 40 60 80 100 120 140 (C) ESR/frequency at 20 C 1.6 100 47 F, 125 V 47 F, 125 V 80 1.2 120 F, 75 V 60 120 F, 75 V ESR (W) Percentage of 50 Hz capacitance 0 0.8 40 680 F, 15 V 680 F, 15 V 20 0.4 1200 F, 6 V 1200 F, 6 V 0 0 101 Revision: 28-Oct-11 102 103 104 (Hz) 102 103 104 105 (Hz) 106 Document Number: 42078 4 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series CA2 www.vishay.com Vishay PERFORMANCE CURVES Impedance/frequency at 20 C 10 2 Impedance () 47 F, 125 V 101 120 F, 75 V 680 F, 15 V 100 1200 F, 6 V 10-1 102 103 104 105 (Hz) 106 Note * All performance curves are provided from historic Arcotronics style CA/CAE datasheet information CROSS REFERENCE VISHAY PART NUMBER ARCOTRONICS PART NUMBER NATO PART NUMBER CA2C476M125A CA2C566M100A CA2C686M075A CA2C826M075A CA2C107M075A CA2C127M075A CA2C157M050A CA2C187M050A CA2C227M050A CA2C277M030A CA2C337M030A CA2C397M020A CA2C477M020A CA2C567M020A CA2C687M015A CA2C827M010A CA2C108M008A CA2C128M006A 402/1/50157/003 402/1/50157/004 402/1/50157/005 402/1/50157/006 402/1/50157/007 402/1/50157/008 402/1/50157/009 402/1/50157/010 402/1/50157/011 402/1/50157/012 402/1/50157/013 402/1/50157/014 402/1/50157/015 402/1/50157/016 402/1/50157/017 402/1/50157/018 402/1/50157/019 402/1/50157/020 5910-99017-2755 5910-99017-2754 5910-99017-2750 5910-99017-2751 5910-99017-2752 5910-99017-2753 5910-99017-2747 5910-99017-2748 5910-99017-2749 5910-99017-2745 5910-99017-2746 5910-99017-2742 5910-99017-2743 5910-99017-2744 5910-99017-2741 5910-99017-2740 5910-99017-2739 5910-99017-2738 CA2C476M125B CA2C566M100B CA2C686M075B CA2C826M075B CA2C107M075B CA2C127M075B CA2C157M050B CA2C187M050B CA2C227M050B CA2C277M030B CA2C337M030B CA2C397M020B CA2C477M020B CA2C567M020B CA2C687M015B CA2C827M010B CA2C108M008B CA2C128M006B 402/1/50158/003 402/1/50158/004 402/1/50158/005 402/1/50158/006 402/1/50158/007 402/1/50158/008 402/1/50158/009 402/1/50158/010 402/1/50158/011 402/1/50158/012 402/1/50158/013 402/1/50158/014 402/1/50158/015 402/1/50158/016 402/1/50158/017 402/1/50158/018 402/1/50158/019 402/1/50158/020 5910-99017-2773 5910-99017-2772 5910-99017-2756 5910-99017-2769 5910-99017-2770 5910-99017-2771 5910-99017-2765 5910-99017-2766 5910-99017-2767 5910-99017-2763 5910-99017-2764 5910-99017-2760 5910-99017-2761 5910-99017-2762 5910-99017-2759 5910-99017-2758 5910-99017-2757 5910-99017-2756 CA CAPC Revision: 28-Oct-11 Document Number: 42078 5 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000