0.00 0.05 0.10 0.15 0.20 0.25 0.30
0
10
20
30
40
50
60
70
80
90
100
EFFICIENCY (%)
LOAD CURRENT (A)
1.2Vout
3.3Vout
0.00 0.05 0.10 0.15 0.20 0.25 0.30
0
10
20
30
40
50
60
70
80
90
100
EFFICIENCY (%)
LOAD CURRENT (A)
1.2Vout
3.3Vout
LMR14203
www.ti.com
SNVS732C –OCTOBER 2011–REVISED APRIL 2013
LMR14203 SIMPLE SWITCHER
®
42Vin, 0.3A Step-Down Voltage Regulator in SOT-23
Check for Samples: LMR14203
1FEATURES DESCRIPTION
The LMR14203 is a PWM DC/DC buck (step-down)
2• Input Voltage Range of 4.5V to 42V regulator. With a wide input range from 4.5V-42V, it is
• Output Voltage Range of 0.765V to 34V suitable for a wide range of applications such as
• Output Current up to 0.3A power conditioning from unregulated sources. They
feature a low RDSON (0.9Ωtypical) internal switch for
• 1.25 MHz Switching Frequency maximum efficiency (85% typical). Operating
• Low Shutdown Iq, 16 µA Typical frequency is fixed at 1.25 MHz allowing the use of
• Short Circuit Protected small external components while still being able to
have low output voltage ripple. Soft-start can be
• Internally Compensated implemented using the shutdown pin with an external
• Soft-Start Function RC circuit allowing the user to tailor the soft-start time
• Thin SOT-23-6 Package (2.97 x 1.65 x 1mm) to a specific application.
• Fully Enabled for WEBENCH® Power Designer The LMR14203 is optimized for up to 300 mA load
current.
PERFORMANCE BENEFITS Additional features include: thermal shutdown, VIN
• Tight Accuracy for Powering Digital ICs under-voltage lockout, and gate drive under-voltage
• Extremely Easy to Use lockout. The LMR14203 is available in a low profile
SOT-6L package.
• Tiny Overall Solution Reduces System Cost
APPLICATIONS
• Point-of-Load Conversions from 5V, 12V, and
24V Rails
• Space Constrained Applications
• Battery Powered Equipment
• Industrial Distributed Power Applications
• Power Meters
• Portable Hand-Held Instruments
System Performance
Efficiency vs Load Current Efficiency vs Load Current
VIN = 12V, VOUT = 1.2V and 3.3V VIN = 24V, VOUT = 1.2V and 3.3V
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2011–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
CB 1
2
3 4
5
6
LMR14203
GND
FB
SW
PIN 1 ID VIN
SHDN
LMR14203
VOUT
VIN
L1
D1
R1
R2
CBOOT
CIN COUT
FB
SW
CB
GND
SHDN
VIN
LMR14203
SNVS732C –OCTOBER 2011–REVISED APRIL 2013
www.ti.com
Connection Diagram
Top View
Figure 1. 6 Lead SOT Package
See Package Number DDC0006A
Pin Descriptions
Pin Name Function
1 CB SW FET gate bias voltage. Connect CBOOT cap between CB and SW.
2 GND Ground connection.
Feedback pin: Set feedback voltage divider ratio with VOUT = VFB (1+(R1/R2)). Resistors should be
3 FB in the 100-10K range to avoid input bias errors.
4 SHDN Logic level shutdown input. Pull to GND to disable the device and pull high to enable the device. If
this function is not used tie to VIN or leave open.
5 VIN Power input voltage pin: 4.5V to 42V normal operating range.
6 SW Power FET output: Connect to inductor, diode, and CBOOT cap.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: LMR14203
LMR14203
www.ti.com
SNVS732C –OCTOBER 2011–REVISED APRIL 2013
Absolute Maximum Ratings(1)(2)
VIN -0.3V to +45V
SHDN -0.3V to (VIN+0.3V) <45V
SW Voltage -0.3V to +45V
CB Voltage above SW Voltage 7V
FB Voltage -0.3V to +5V
Maximum Junction Temperature 150°C
Power Dissipation(3) Internally Limited
For soldering specifications:http://www.ti.com/lit/SNOA549
ESD Susceptibility(4)
Human Body Model 1.5 kV
(1) Absolute maximum ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the
device is intended to be functional, but device parameter specifications may not be ensured. For ensured specifications and test
conditions, see the Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(3) The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal
resistance, θJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated
using: PD(MAX) = (TJ(MAX) −TA)/θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and
the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. Thermal
shutdown engages at TJ=175°C (typ.) and disengages at TJ=155°C (typ).
(4) Human Body Model, applicable std. JESD22-A114-C.
Operating Conditions
Operating Junction Temperature Range(1) −40°C to +125°C
Storage Temperature −65°C to +150°C
Input Voltage VIN 4.5V to 42V
SW Voltage Up to 42V
(1) All limits specified at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits are
100% production tested. All limits at temperature extremes are ensured via correlation using standard Statistical Quality Control (SQC)
methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
Copyright © 2011–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LMR14203
LMR14203
SNVS732C –OCTOBER 2011–REVISED APRIL 2013
www.ti.com
Electrical Characteristics
Specifications in standard type face are for TJ= 25°C and those with boldface type apply over the full Operating
Temperature Range ( TJ=−40°C to +125°C). Minimum and Maximum limits are ensured through test, design, or statistical
correlation. Typical values represent the most likely parametric norm at TJ= +25°C, and are provided for reference purposes
only. Unless otherwise stated the following conditions apply: VIN = 12V.
Parameter Test Conditions Min(1) Typ(2) Max(1) Units
IQQuiescent current SHDN = 0V 16 40 µA
Device On, Not Switching 1.30 1.75 mA
Device On, No Load 1.35 1.85
RDSON Switch ON resistance See (3) 0.9 1.6 Ω
ILSW Switch leakage current VIN = 42V 0.0 0.5 µA
ICL Switch current limit See (4) 525 mA
IFB Feedback pin bias current See (5) 0.1 1.0 µA
VFB FB Pin reference voltage 0.747 0.765 0.782 V
tMIN Minimum ON time 100 ns
fSW VFB = 0.5V 0.95 1.25 1.50
Switching frequency MHz
VFB = 0V 0.35
DMAX Maximum duty cycle 81 87 %
VUVP Undervoltage lockout thresholds On threshold 4.4 3.7 V
Off threshold 3.5 3.25
VSHDN Shutdown threshold Device on 2.3 1.0 V
Device off 0.9 0.3
ISHDN Shutdown pin input bias current VSHDN = 2.3V(5) 0.05 1.5 µA
VSHDN = 0V 0.02 1.5
THERMAL SPECIFICATIONS
RθJA Junction-to-Ambient Thermal See (6) 121 °C/W
Resistance, SOT-6L Package
(1) All limits specified at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits are
100% production tested. All limits at temperature extremes are ensured via correlation using standard Statistical Quality Control (SQC)
methods. All limits are used to calculate Average Outgoing Quality Level (AOQL).
(2) Typical numbers are at 25°C and represent the most likely norm.
(3) Includes the bond wires, RDSON from VIN pin to SW pin.
(4) Current limit at 0% duty cycle.
(5) Bias currents flow into pin.
(6) All numbers apply for packages soldered directly onto a 3" x 3" PC board with 2 oz. copper on 4 layers in still air in accordance to
JEDEC standards. Thermal resistance varies greatly with layout, copper thickness, number of layers in PCB, power distribution, number
of thermal vias, board size, ambient temperature, and air flow.
4Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: LMR14203
SWITCH CURRENT LIMIT (mA)
1.0 1.6 2.2 2.8 3.4 4.0
800
600
400
200
0
SHDN PIN VOLTAGE (V)
0.0 0.1 0.2 0.3
LOAD CURRENT (A)
0
20
40
60
80
100
EFFICIENCY (%)
VIN = 36V
VIN = 12V
VIN = 24V
LMR14203
www.ti.com
SNVS732C –OCTOBER 2011–REVISED APRIL 2013
Typical Performance Characteristics
Efficiency vs. Load Current
(VOUT = 3.3V) Input UVLO Voltage vs. Temperature
Figure 2. Figure 3.
Switch Current Limit vs. SHDN Pin Voltage
(Soft-start Implementation) SHDN Pin Current vs. SHDN Pin Voltage
Figure 4. Figure 5.
Switching Node and Output Voltage Waveforms
VIN = 12V, VOUT = 3.3V, IOUT = 200 mA
Top trace: VOUT, 10 mV/div, AC Coupled
Bottom trace: SW, 5V/div, DC Coupled
T = 1 µs/div Figure 6.
Copyright © 2011–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LMR14203
Max Duty
Cycle Limit
OSC
DC
LIMIT
SET
+
+
-
+
PWM
Comp RESET FET
Driver
BUCK
DRIVE
+
-
Error
Amp
FB
Bandgap Soft
Start Thermal
Shutdown
TSD
SHDN
Inductor
Current
Measurement
CB
SW
GND
UVLO
Comp
BG
UVLO
Voltage
Regulator
VIN
LMR14203
SNVS732C –OCTOBER 2011–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
Load Transient Waveforms Start-Up Waveform
VIN = 12V, VOUT = 3.3V, IOUT = 300 mA to 200 mA to 300 mA VIN = 12V, VOUT = 3.3V, IOUT = 50 mA
Top trace: VOUT, 20 mV/div, AC Coupled Top trace: VOUT, 1V/div, DC Coupled
Bottom trace: IOUT, 100 mA/div, DC Coupled Bottom trace: SHDN, 2V/div, DC Coupled
T = 200 µs/div T = 40 µs/div
Figure 7. Figure 8.
Block Diagram
6Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: LMR14203
L = (VIN - VOUT)VOUT
VIN x IRIPPLE x fSW
LMR14203
www.ti.com
SNVS732C –OCTOBER 2011–REVISED APRIL 2013
APPLICATION INFORMATION
Protection
The LMR14203 has dedicated protection circuitry running during normal operation to protect the IC. The thermal
shutdown circuitry turns off the power device when the die temperature reaches excessive levels. The UVLO
comparator protects the power device during supply power startup and shutdown to prevent operation at
voltages less than the minimum input voltage. A gate drive (CB) under-voltage lockout is included to ensure that
there is enough gate drive voltage to drive the MOSFET before the device tries to start switching. The
LMR14203 also features a shutdown mode decreasing the supply current to approximately 16 µA.
Continuous Conduction Mode
The LMR14203 contains a current-mode, PWM buck regulator. A buck regulator steps the input voltage down to
a lower output voltage. In continuous conduction mode (when the inductor current never reaches zero at steady
state), the buck regulator operates in two cycles. The power switch is connected between VIN and SW. In the first
cycle of operation the transistor is closed and the diode is reverse biased. Energy is collected in the inductor and
the load current is supplied by COUT and the rising current through the inductor. During the second cycle the
transistor is open and the diode is forward biased due to the fact that the inductor current cannot instantaneously
change direction. The energy stored in the inductor is transferred to the load and output capacitor. The ratio of
these two cycles determines the output voltage. The output voltage is defined approximately as:
D=VOUT/VIN and D’ = (1-D)
where
• D is the duty cycle of the switch. (1)
D and D' will be required for design calculations.
Design Procedure
This section presents guidelines for selecting external components.
Setting the Output Voltage
The output voltage is set using the feedback pin and a resistor divider connected to the output as shown on the
front page schematic. The feedback pin voltage is 0.765V, so the ratio of the feedback resistors sets the output
voltage according to the following equation:
VOUT=0.765V(1+(R1/R2)) (2)
Typically R2 will be given as 100Ω-10 kΩfor a starting value. To solve for R1 given R2 and VOUT use
R1=R2((VOUT/0.765V)-1).
Input Capacitor
A low ESR ceramic capacitor (CIN) is needed between the VIN pin and GND pin. This capacitor prevents large
voltage transients from appearing at the input. Use a 2.2 µF-10 µF value with X5R or X7R dielectric. Depending
on construction, a ceramic capacitor’s value can decrease up to 50% of its nominal value when rated voltage is
applied. Consult with the capacitor manufacturer's data sheet for information on capacitor derating over voltage
and temperature.
Inductor Selection
The most critical parameters for the inductor are the inductance, peak current, and the DC resistance. The
inductance is related to the peak-to-peak inductor ripple current, the input and the output voltages.
(3)
A higher value of ripple current reduces inductance, but increases the conductance loss, core loss, and current
stress for the inductor and switch devices. It also requires a bigger output capacitor for the same output voltage
ripple requirement. A reasonable value is setting the ripple current to be 30% of the DC output current. Since the
ripple current increases with the input voltage, the maximum input voltage is always used to determine the
inductance. The DC resistance of the inductor is a key parameter for the efficiency. Lower DC resistance is
Copyright © 2011–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LMR14203
LMR14203
SNVS732C –OCTOBER 2011–REVISED APRIL 2013
www.ti.com
available with a bigger winding area. A good tradeoff between the efficiency and the core size is letting the
inductor copper loss equal 2% of the output power. See AN-1197 SNVA038 for more information on selecting
inductors. A good starting point for most applications is a 10 µH to 22 µH with a 0.7A or greater current rating for
the LMR14203. Using such a rating will enable the LMR14203 to current limit without saturating the inductor.
This is preferable to the device going into thermal shutdown mode and the possibility of damaging the inductor if
the output is shorted to ground or other longterm overload.
Output Capacitor
The selection of COUT is driven by the maximum allowable output voltage ripple. The output ripple in the constant
frequency, PWM mode is approximated by:
VRIPPLE = IRIPPLE(ESR+(1/(8fSWCOUT))) (4)
The ESR term usually plays the dominant role in determining the voltage ripple. Low ESR ceramic capacitors are
recommended. Capacitors in the range of 22 µF-100 µF are a good starting point with an ESR of 0.1Ωor less.
Bootstrap Capacitor
A 0.15 µF ceramic capacitor or larger is recommended for the bootstrap capacitor (CBOOT). For applications
where the input voltage is less than twice the output voltage a larger capacitor is recommended, generally 0.15
µF to 1 µF to ensure plenty of gate drive for the internal switches and a consistently low RDSON.
Soft-Start Components
The LMR14203 has circuitry that is used in conjunction with the SHDN pin to limit the inrush current on start-up
of the DC/DC switching regulator. The SHDN pin in conjunction with a RC filter is used to tailor the soft-start for a
specific application. When a voltage applied to the SHDN pin is between 0V and up to 2.3V it will cause the cycle
by cycle current limit in the power stage to be modulated for minimum current limit at 0V up to the rated current
limit at 2.3V. Thus controlling the output rise time and inrush current at startup. The resistor value should be
selected so the current sourced into the SHDN pin will be greater then the leakage current of the SHDN pin (1.5
µA ) when the voltage at SHDN is equal or greater then 2.3V.
Shutdown Operation
The SHDN pin of the LMR14203 is designed so that it may be controlled using 2.3V or higher logic signals. If the
shutdown function is not to be used the SHDN pin may be tied to VIN. The maximum voltage to the SHDN pin
should not exceed 42V. If the use of a higher voltage is desired due to system or other constraints it may be
used, however a 100 kΩor larger resistor is recommended between the applied voltage and the SHDN pin to
protect the device.
SCHOTTKY Diode
The breakdown voltage rating of the diode (D1) is preferred to be 25% higher than the maximum input voltage.
The current rating for the diode should be equal to the maximum output current for best reliability in most
applications. In cases where the duty cycle is greater than 50%, the average diode current is lower. In this case it
is possible to use a diode with a lower average current rating, approximately (1-D)IOUT, however the peak current
rating should be higher than the maximum load current. A 0.5A to 1A rated diode is a good starting point.
Layout Considerations
To reduce problems with conducted noise pick up, the ground side of the feedback network should be connected
directly to the GND pin with its own connection. The feedback network, resistors R1 and R2, should be kept
close to the FB pin, and away from the inductor to minimize coupling noise into the feedback pin. The input
bypass capacitor CIN must be placed close to the VIN pin. This will reduce copper trace resistance which effects
input voltage ripple of the IC. The inductor L1 should be placed close to the SW pin to reduce EMI and capacitive
coupling. The output capacitor, COUT should be placed close to the junction of L1 and the diode D1. The L1, D1,
and COUT trace should be as short as possible to reduce conducted and radiated noise and increase overall
efficiency. The ground connection for the diode, CIN, and COUT should be as small as possible and tied to the
system ground plane in only one spot (preferably at the COUT ground point) to minimize conducted noise in the
system ground plane. For more detail on switching power supply layout considerations see Application Note AN-
1149: Layout Guidelines for Switching Power Supplies SNVA021.
8Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: LMR14203
FB
GND
SW
VIN CB
SHDN
LMR14203
COUT
12V OUT
15V to 42V IN
L1
47
D1
60V 500 mA
CBOOT
CIN
R1
R2
14.7k
1k 22 PF
0.15 PF
PH
2.2 PF
FB
GND
SW
CB
SHDN
LMR14203
COUT
3.3V OUT
4.5V to 42V IN
L1
D1
60V 500 mA
CIN
R1
R2
3.4k
1.02k
2.2 PF
0.15PF
47 PF
15 PH
CBOOT
VIN
LMR14203
www.ti.com
SNVS732C –OCTOBER 2011–REVISED APRIL 2013
Typical Applications
Figure 9. Application Circuit, 3.3V Output
Figure 10. Application Circuit, 5V Output
Figure 11. Application Circuit, 12V Output
Copyright © 2011–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LMR14203
FB
GND
SW
VIN CB
SHDN
LMR14203
COUT
0.8V OUT
4.5V to 12V IN
L1
10
D1
60V 500 mA
CBOOT
R1
R2
30.9
787
PH
0.15 PF
2.2 PF100PF
CIN
FB
GND
SW
CB
SHDN
LMR14203
COUT
15V OUT
18V to 42V IN
L1
47
D1
60V 500 mA
CBOOT
CIN
R1
R2
28k
1.5k
PH
2.2 PF
0.15PF
22 PF
VIN
LMR14203
SNVS732C –OCTOBER 2011–REVISED APRIL 2013
www.ti.com
Figure 12. Application Circuit, 15V Output
Figure 13. Application Circuit, 0.8V Output
10 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated
Product Folder Links: LMR14203
LMR14203
www.ti.com
SNVS732C –OCTOBER 2011–REVISED APRIL 2013
REVISION HISTORY
Changes from Revision B (April 2013) to Revision C Page
• Changed layout of National Data Sheet to TI format .......................................................................................................... 10
Copyright © 2011–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LMR14203
PACKAGE OPTION ADDENDUM
www.ti.com 28-Feb-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LMR14203XMK/NOPB ACTIVE SOT-23-THIN DDC 6 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SJ3B
LMR14203XMKE/NOPB ACTIVE SOT-23-THIN DDC 6 250 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SJ3B
LMR14203XMKX/NOPB ACTIVE SOT-23-THIN DDC 6 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SJ3B
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
PACKAGE OPTION ADDENDUM
www.ti.com 28-Feb-2017
Addendum-Page 2
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LMR14203XMK/NOPB SOT-
23-THIN DDC 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LMR14203XMKE/NOPB SOT-
23-THIN DDC 6 250 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LMR14203XMKX/NOPB SOT-
23-THIN DDC 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
PACKAGE MATERIALS INFORMATION
www.ti.com 3-Mar-2017
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LMR14203XMK/NOPB SOT-23-THIN DDC 6 1000 210.0 185.0 35.0
LMR14203XMKE/NOPB SOT-23-THIN DDC 6 250 210.0 185.0 35.0
LMR14203XMKX/NOPB SOT-23-THIN DDC 6 3000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 3-Mar-2017
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LMR14203XMK/NOPB LMR14203XMKE/NOPB LMR14203XMKX/NOPB