(R) INA156 INA 156 For most current data sheet and other product information, visit www.burr-brown.com Single-Supply, Rail-to-Rail Output, CMOS INSTRUMENTATION AMPLIFIER FEATURES APPLICATIONS INDUSTRIAL SENSOR AMPLIFIERS: Bridge, RTD, Thermocouple, Flow, Position MEDICAL EQUIPMENT: ECG, EEG, EMG Amplifiers DRIVING A/D CONVERTERS PCMCIA CARDS AUDIO PROCESSING COMMUNICATIONS TEST EQUIPMENT LOW COST AUTOMOTIVE INSTRUMENTATION RAIL-TO-RAIL OUTPUT SWING: Within 20mV LOW OFFSET DRIFT: 5V/C INTERNAL FIXED GAIN = 10V/V OR 50V/V SPECIFIED TEMPERATURE RANGE: -55C to +125C LOW INPUT BIAS CURRENT: 1pA WIDE BANDWIDTH: 550kHz in G = 10 HIGH SLEW RATE: 6.5V/s LOW COST TINY MSOP-8 PACKAGES DESCRIPTION The INA156 is a low-cost CMOS instrumentation amplifier with rail-to-rail output swing optimized for low-voltage, single-supply operation. Wide bandwidth (550kHz in G = 10) and high slew rate (6.5V/s) make the INA156 suitable for driving sampling A/D converters as well as general purpose and audio applications. Fast settling time allows use with higher speed sensors and transducers, and rapid scanning data acquisition systems. RG Gain can be set to 10V/V or 50V/V by pin strapping. Gains between these two values can be obtained with the addition of a single resistor. The INA156 is fully specified over the supply range of +2.7V to +5.5V. The INA156 is available in an MSOP-8 surface-mount package specified for operation over the temperature range -55C to 125C. G = 10 pins open G = 50 pins connected 1 V+ RG 8 7 INA156 5k Ref 5 200k 5k 22.2k 22.2k 200k + - VO = (VIN - VIN) * G + VREF - VIN 2 V+ 3 A1 6 A2 VO IN 4 V- International Airport Industrial Park * Mailing Address: PO Box 11400, Tucson, AZ 85734 * Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 * Tel: (520) 746-1111 Twx: 910-952-1111 * Internet: http://www.burr-brown.com/ * Cable: BBRCORP * Telex: 066-6491 * FAX: (520) 889-1510 * Immediate Product Info: (800) 548-6132 (c)1999 Burr-Brown Corporation SBOS119 PDS-1565A Printed in U.S.A. December, 1999 SPECIFICATIONS: VS = +2.7V to +5.5V Boldface limits apply over the specified temperature range, TA = -55C to +125C At TA = +25C, RL = 10k connected to VS/2. RG pins open (G = 10), and Ref = VS /2, unless otherwise noted. INA156E, A PARAMETER CONDITION INPUT Offset Voltage, RTI Over Temperature Drift vs Power Supply Over Temperature vs Time VOS dVOS/dT PSRR MIN TYP VS = +5.0V, VCM = VS/2 2.5 VS = +2.7V to +6V, VCM = 0.2 * VS 5 50 0.4 MAX UNITS 8 mV mV V/C V/V V/V V/mo 9 200 250 INPUT VOLTAGE RANGE Safe Input Voltage Common-Mode Range(1) Common-Mode Rejection Ratio Over Temperature VCM CMRR VS = 5.5V VS = 2.7V VS = 5.5V, 0.6V < VCM < 3.7V, G = 10 VS = 5.5V, 0.6V < VCM < 3.7V, G = 50 Over Temperature (V-) - 0.5 0.3 0.2 66 65 74 73 INPUT IMPEDANCE Differential Common-Mode (V+) + 0.5 5.2(2) 2.5(2) 78 87 || pF || pF 1013 || 3 1013 || 3 INPUT BIAS CURRENT Input Bias Current Offset Current 1 1 IB IOS 10 VS = 5.5V, VO = 0.02V to 5.48V, G = 10 VS = 5.5V, VO = 0.05V to 5.45V, G = 50 vs Temperature Nonlinearity Over Temperature VS = 5.5V, G = 10 or 50 OUTPUT Voltage Output Swing from Rail Over Temperature Short-Circuit Current Capacitance Load (stable operation) FREQUENCY RESPONSE Bandwidth, -3dB BW Slew Rate Settling Time: 0.1% SR tS 0.01% TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance MSOP-8 Surface Mount SO-8 Surface Mount 5 Short-Circuit to Ground 50 See Typical Curve G = 10 G = 50 VS = 5.5V, CL = 100pF VS = 5.5V, VO = 2V Step, CL = 100pF, G = 10 VS = 5.5V, VO = 2V Step, CL = 100pF, G = 50 VS = 5.5V, VO = 2V Step, CL = 100pF, G = 10 VS = 5.5V, VO = 2V Step, CL = 100pF, G = 50 50% Input Overload 550 110 6.5 5 11 8 15 0.2 See Typical Curve THD+N POWER SUPPLY Specified Voltage Range Operating Voltage Range Quiescent Current Over Temperature 50 G = 10 + 400k/(10k + RG) V/V 0.08 0.4 2 10 0.1 0.8 15 30 0.005 0.015 0.015 G = 10, RL = 10k, GERR < 0.4% +2.7 VIN = 0, IO = 0 VIN = 0, IO = 0 20 20 -55 -65 -65 JA 150 150 V/V % ppm/C % ppm/C % of FSR % of FSR mV mV mA kHz kHz V/s s s s s s +5.5 +2.5 to +6 1.8 pA pA V/Vp-p nV/Hz nV/Hz nV/Hz fA/Hz 4.5 260 99 40 2 GAIN Gain Equation Gain Error(3) vs Temperature Overload Recovery Total Harmonic Distortion + Noise 10 10 RS = 0, G = 10 or 50 NOISE, RTI Voltage Noise: f = 0.1Hz to 10Hz Voltage Noise Density: f = 10Hz f = 100Hz f = 1kHz Current Noise: f = 1kHz V V V dB dB dB dB 2.5 3.2 V V mA mA +125 +150 +150 C C C C/W C/W NOTES: (1) For further information, refer to typical performance curves on common-mode input range. (2) Operation beyond (V+) - 1.8V (max) results in reduced common-mode rejection. See discussion and Figure 6 in the text of this data sheet. (3) Does not include error and TCR of additional optional gain-setting resistor in series with RG, if used. (R) INA156 2 ELECTROSTATIC DISCHARGE SENSITIVITY PIN CONFIGURATION Top View MSOP RG 1 8 RG - VIN 2 V+ 7 V+ IN 3 6 VOUT V- 4 5 Ref This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. INA156 ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ABSOLUTE MAXIMUM RATINGS(1) Supply Voltage, V+ to V- ................................................................... 7.5V Signal Input Terminals, Voltage(2) .................. (V-) - 0.5V to (V+) + 0.5V Current(2) .................................................... 10mA Output Short-Circuit(3) .............................................................. Continuous Operating Temperature .................................................. -65C to +150C Storage Temperature ..................................................... -65C to +150C Junction Temperature .................................................................... +150C Lead Temperature (soldering, 10s) ............................................... +300C NOTES: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. (2) Input terminals are diode-clamped to the power supply rails. Input signals that can swing more that 0.5V beyond the supply rails should be current limited to 10mA or less. (3) Short circuit to ground. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER INA156 EA MSOP-8 337 -55C to +125C A56 " " " " " SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(1) TRANSPORT MEDIA INA156EA/250 INA156EA/2K5 Tape and Reel Tape and Reel NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of "INA156EA/2K5" will get a single 2500-piece Tape and Reel. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. (R) 3 INA156 TYPICAL PERFORMANCE CURVES At TA = +25C, VS = 5.5V, RL = 10k connected to VS/2. RG pins open (G = 10), and Ref = VS /2, unless otherwise noted. GAIN vs FREQUENCY COMMON-MODE REJECTION RATIO vs FREQUENCY 40 100 35 90 30 G = 50 80 G = 50 G = 10 70 20 G =10 15 60 CMRR (dB) Gain (dB) 25 50 40 30 10 20 5 10 0 0 1 10 100 1k 10k 100k 1M 10M 0.1 1 10 100 Frequency (Hz) 100k 6 Maximum Output Voltage (Vp-p) 90 80 70 60 50 40 30 20 10 5 4 3 2 1 VS = 5.5V 0 0 1 10 100 1k 10k 100k 1 1M 10 100 1k 10k 100k 1M Frequency (Hz) Frequency (Hz) SHORT-CIRCUIT CURRENT AND QUIESCENT CURRENT vs POWER SUPPLY QUIESCENT CURRENT AND SHORT-CIRCUIT CURRENT vs TEMPERATURE 100 2.1 55 -ISC 50 2.5 IQ -ISC 2.0 80 2.0 +ISC +ISC 40 1.8 35 1.7 30 1.6 2.5 3 3.5 4.5 4.0 Supply Voltage (V) 5 5.5 1.5 40 1.0 20 0.5 0 75 6 (R) INA156 60 0 1.5 25 ISC (mA) IQ IQ (mA) 1.9 45 4 -50 -25 0 25 50 75 Temperature (C) 100 125 150 IQ (mA) PSRR (dB) 10k MAXIMUM OUTPUT VOLTAGE vs FREQUENCY POWER SUPPLY REJECTION RATIO vs FREQUENCY 100 ISC (mA) 1k Frequency (Hz) TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25C, VS = 5.5V, RL = 10k connected to VS/2. RG pins open (G = 10), and Ref = VS /2, unless otherwise noted. TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY INPUT VOLTAGE AND CURRENT NOISE DENSITY vs FREQUENCY 10k 1 100 10 in 100 1 RL = 2k 0.1 THD+N (%) 1k Current Noise (fA/Hz) Voltage Noise (nV/Hz) RL = 600 en G = 50 RL = 600 RL = 10k 0.01 G = 10 RL = 2k 10 0.1 10 1 100 1k 10k RL =10k 0.001 0.1 100k 10 100 1k 10k Frequency (Hz) Frequency (Hz) 0.1Hz TO 10Hz VOLTAGE NOISE INPUT BIAS CURRENT vs TEMPERATURE 10k 1V/div Input Bias Current (pA) 1k 100 10 1 Input-Referred 0.1 -75 500ms/div -50 -25 0 25 50 75 100 125 150 125 150 Temperature (C) SLEW RATE vs POWER SUPPLY SLEW RATE vs TEMPERATURE 7 10 9 8 6 Slew Rate (V/s) Slew Rate (Vs) 6.5 5.5 5 7 6 5 4 3 2 4.5 1 4 0 2.5 3 3.5 4 4.5 5 5.5 6 75 Supply Voltage (V) -50 -25 0 25 50 75 100 Temperature (C) (R) 5 INA156 TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25C, VS = 5.5V, RL = 10k connected to VS/2. RG pins open (G = 10), and Ref = VS /2, unless otherwise noted. OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 18 16 16 14 14 Percent of Amplifiers (%) 18 12 10 8 6 4 12 10 8 6 4 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 2 4 6 8 10 12 14 16 18 20 10 8 6 4 2 0 -2 -4 0 -6 2 0 -8 2 -10 Production Distribution (%) VOS TYPICAL PRODUCTION DISTRIBUTION Offset Voltage (mV) Offset Voltage Drift (V/C) OVERSHOOT vs LOAD CAPACITANCE SETTLING TIME vs LOAD CAPACITANCE 60 20 18 12 Overshoot (%) 14 0.1%, G = 50 10 0.01%, G = 10 8 6 0.1%, G = 10 40 G = 10 30 20 G = 50 4 10 2 0 0 10 100 1k 10 10k 100 1k Load Capacitance (pF) Load Capacitance (pF) SMALL-SIGNAL STEP RESPONSE G = 10, CL = 100pF, RL = 10k SMALL-SIGNAL STEP RESPONSE G = 50, CL = 100pF, RL = 10k 100mV/div 100mV/div Settling Time (s) 50 0.01%, G = 50 16 5s/div 5s/div (R) INA156 6 10k TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25C, VS = 5.5V, RL = 10k connected to VS/2. RG pins open (G = 10), and Ref = VS /2, unless otherwise noted. LARGE-SIGNAL STEP RESPONSE G = 10, G = 50, CL = 100pF, RL = 10k OUTPUT VOLTAGE SWING vs OUTPUT CURRENT 5 1V/div Output Voltage (V) 4 +125C -55C +25C 3 2 +125C -55C +25C 1 0 0 1s/div 10 20 50 60 70 80 90 100 INPUT COMMON-MODE RANGE vs OUTPUT VOLTAGE, G = 50 6 6 G = 50 G = 10 5 5 4 4 VCM (V) VCM (V) 40 Output Current (mA) INPUT COMMON-MODE RANGE vs REFERENCE VOLTAGE, G = 10 3 2 3 Ref = 0V Ref = 2.75V Ref = 5.5V 2 0.9V- + 0.1Ref < VCM < 0.9V+ + 0.1Ref 1 0.9V- + 0.04VOUT + 0.06Ref < VCM < 0.9V+ + 0.04VOUT + 0.06Ref 1 0 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 VREF (V) VOUT (V) COMMON-MODE REJECTION RATIO PRODUCTION DISTRIBUTION COMMON-MODE REJECTION RATIO PRODUCTION DISTRIBUTION 9 5 5.5 10 80dB 9 8 Production Distribution (%) G = 10 7 6 5 4 3 2 80dB G = 50 8 7 6 5 4 3 2 1 0 0 -200 -180 -160 -140 -120 -100 -80 -60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 1 -500 -450 -400 -350 -300 -250 -200 -150 -100 -50 0 50 100 150 200 250 300 350 400 450 500 Production Distribution (%) 30 CMRR (V/V) CMRR (V/V) (R) 7 INA156 APPLICATIONS INFORMATION OPERATING VOLTAGE Figure 1 shows the basic connections required for operation of the INA156. Applications with noisy or high impedance power supplies may require decoupling capacitors close to the device pins, as shown. The INA156 is fully specified and guaranteed over the supply range +2.7V to +5.5V, with key parameters guaranteed over the temperature range of -55C to +125C. Parameters that vary significantly with operating voltages, load conditions or temperature are shown in the Typical Performance Curves. The output is referred to the output reference terminal, Ref, which is normally set to VS/2. This must be a low-impedance connection to ensure good common-mode rejection. The INA156 can be operated from either single or dual power supplies. By adjusting the voltage applied to the reference terminal, the input common-mode voltage range and the output range can be adjusted within the bounds shown in the Typical Performance Curves. Figure 2 shows a bridge amplifier circuit operated from a single +5V power supply. The bridge provides a relatively small differential voltage on top of an input common-mode voltage near 2.5V. In addition, for the G = 50 configuration, the connection between pins 1 and 8 must be low-impedance. A connection impedance of 20 can cause a 0.2% shift in gain error. External Resistor RG: 10 < G < 50 V+ Gain Pins Connected: G = 50 0.1F Gain Pins Open: G = 10 1 7 G = 10 + 8 200k 5 22.2k 22.2k 10 20 30 40 50 Open 30k 10k 3.3k Short 200k 6 A2 3 V+ RG () A1 2 - VIN DESIRED GAIN (V/V) 5k 5k Ref 400k 10k + RG + - - VIN ) * G + VREF VOUT = (VIN IN Also drawn in simplified form: V+ INA156 4 + VIN 3 1 0.1F Single Supply - VIN Dual Supply 7 4 V- V- VOUT 5 8 2 6 INA156 Ref FIGURE 1. Basic Connections. +5V Bridge Sensor (2) + VIN 3 1 - VIN 7 INA156 VOUT = 0.01V to 4.99V 4 8 2 6 5 NOTES: (1) VREF should be adjusted for the desired output level, keeping in mind that the value of VREF affects the common-mode input range. See Typical Performance Curves. (2) For best performance, the common-mode input voltage should be kept away from the transition range of (V+) - 1.8V to (V+) - 0.8V. VREF(1) FIGURE 2. Single-Supply Bridge Amplifier. (R) INA156 8 SETTING THE GAIN INPUT BIAS CURRENT RETURN Gain of 10 is achieved simply by leaving the two gain pins (1 and 8) open. Gain of 50 is achieved by connecting the gain pins together directly. In the G = 10 configuration, the gain error is less than 0.4%. In the G = 50 configuration, the gain error is less than 0.8%. The input impedance of the INA156 is extremely high-- approximately 1013, making it ideal for use with high-impedance sources. However, a path must be provided for the input bias current of both inputs. This input bias current is less than 10pA and is virtually independent of the input voltage. Gain can be set to any value between 10 and 50 by connecting a resistor RG between the gain pins according to the following equation: Input circuitry must provide a path for this input bias current for proper operation. Figure 5 shows various provisions for an input bias current path. Without a bias current path, the inputs will float to a potential that exceeds the commonmode range and the input amplifier will saturate. 10 + 400k/(10k + RG) (1) This is demonstrated in Figure 1 and is shown with the commonly used gains and resistor RG values. However, because the absolute value of internal resistors is not guaranteed, using the INA156 in this configuration will increase the gain error and gain drift with temperature, as shown in Figure 3. 2.0 400 360 Gain Drift 1.6 320 1.4 280 1.2 250 1.0 200 0.8 160 Gain Error 0.6 120 0.4 80 0.2 40 0 3 Gain Drift (ppm/C) 1.8 Gain Error (%) If the differential source resistance is low, the bias current return path can be connected to one input (see the thermocouple in Figure 5). With higher source impedance, using two equal resistors provides a balanced input with advantages of lower input offset voltage due to bias current and better high-frequency common-mode rejection. 1 Microphone, Hydrophone, etc. 6 INA156 8 2 47k 5 47k VREF 0 10 15 25 20 30 35 40 45 50 Gain (V/V) 3 FIGURE 3. Typical Gain Error and Gain Error Drift with External Resistor. 1 Thermocouple 8 OFFSET TRIMMING 2 Offset voltage can be adjusted by applying a correction voltage to the reference terminal. Figure 4 shows an optional circuit for trimming the output offset voltage. The voltage applied to the Ref terminal is added to the output signal. An op amp buffer is used to provide low impedance at the Ref terminal to preserve good common-mode rejection. VREF V -(2) IN 6 INA156 8 2 6 INA156 8 2 Low-resistance thermocouple provides bias current return. 3 3 1 5 10k 1 +(2) VIN 6 INA156 VO 5 VREF Center-tap provides bias current return (1) 5 Ref OPA336 Bridge Sensor 3 1 Adjustable Voltage 6 INA156 8 2 NOTES: (1) VREF should be adjusted for the desired output level. The value of VREF affects the common-mode input range. (2) For best performance, common-mode input voltage should be less than (V+) - 1.8V or greater than (V+) - 0.8V. 5 VREF FIGURE 4. Optional Trimming of Output Offset Voltage. Bridge resistance provides bias current return FIGURE 5. Providing an Input Common-Mode Current Path. (R) 9 INA156 INPUT COMMON-MODE RANGE 5 The input common-mode range of the INA156 for various operating conditions is shown in the Typical Performance Curves. The common-mode input range is limited by the output voltage swing of A1, an internal circuit node. For the G = 10 configuration, output voltage of A1 can be expressed as: Input Offset Voltage (mV) VOUTA1 = - 1/9VREF + (1 + 1/9) VIN- (2) The input common-mode voltage range can be calculated using this equation, given that the output of A1 can swing to within 20mV of either rail. When the input common-mode range is exceeded (A1's output is saturated), A2 can still be in linear operation and respond to changes in the non-inverting input voltage. However, the output voltage will be invalid. The common-mode range for the G = 50 configuration is included in the typical performance curve, "Input CommonMode Range vs Output Voltage." 3 2 1 0 -1 -2 -3 -4 VS = 5.5V -5 0.0 0.5 1.5 1.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Input Common-Mode Voltage (V) FIGURE 6. Input Offset Voltage Changes with CommonMode Voltage. V+ NOTE: Output is referred to V+. INPUT RANGE FOR BEST ACCURACY The internal amplifiers have rail-to-rail input stages, achieved by using complementary n-channel and p-channel input pairs. The common-mode input voltage determines whether the p-channel or the n-channel input stage is operating. The transition between the input stages is gradual and occurs between (V+) - 1.8V to (V+) - 1V. Due to these characteristics, operating the INA156 with input voltages within the transition region of (V+) - 1.8V to (V+) - 0.8V results in a shift in input offset voltage, and reduced common-mode and power supply rejection performance. Typical patterns of the offset voltage change throughout the input common-mode range are illustrated in Figure 6. The INA156 can be operated below or above the transition region with excellent results. Figure 7 demonstrates the use of the INA156 in a single-supply, high-side current monitor. In this application, the INA156 is operated above the transition region. Ref 2 5 7 0.02 1 50mV 6 INA156 4 8 3 IL 2.5A Load G = 10 Pins 1 and 8 Open FIGURE 7. Single-Supply, High-Side Current Monitor. RLIM RAIL-TO-RAIL OUTPUT 3 IOVERLOAD 10mA max A class AB output stage with common-source transistors is used to achieve rail-to-rail output. For resistive loads greater than 10k, the output voltage can swing to within a few millivolts of the supply rail while maintaining low gain error. For heavier loads and over temperature, see the typical performance curve "Output Voltage Swing vs Output Current." The INA156's low output impedance at high frequencies makes it suitable for directly driving Capacitive Digital-to-Analog (CDAC) input A/D converters, as shown in Figure 9. 1 8 6 INA156 VOUT 5 2 RLIM VREF FIGURE 8. Input Current Protection for Voltages Exceeding the Supply Voltage. +5V INPUT PROTECTION 3 Device inputs are protected by ESD diodes that will conduct if the input voltages exceed the power supplies by more than 500mV. Momentary voltages greater than 500mV beyond the power supply can be tolerated if the current on the input pins is limited to 10mA. This is easily accomplished with input resistors RLIM, as shown in Figure 8. Many input signals are inherently current-limited to less than 10mA. Therefore, a limiting resistor is not required. 1 7 2 6 INA156 4 8 5 ADS7818 or ADS7834 12-Bits fSAMPLE = 500kHz NOTE: G = 10 configuration FIGURE 9. Driving Capacitive-Input A/D Converter. (R) INA156 Transistion N-Channel Region Operation P-Channel Operation 4 10 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) INA156EA/250 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR INA156EA/250G4 ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR INA156EA/2K5 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR INA156EA/2K5G4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant INA156EA/250 VSSOP DGK 8 250 180.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 INA156EA/2K5 VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) INA156EA/250 VSSOP DGK INA156EA/2K5 VSSOP DGK 8 250 210.0 185.0 35.0 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated