LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
LM96080 System Hardware Monitor with 2-Wire Serial Interface
Check for Samples: LM96080
1FEATURES DESCRIPTION
LM96080, compatible to LM80, is a hardware monitor
2 Local Temperature Sensing that contains a 10-bit delta-sigma ADC capable of
7 Positive Voltage Inputs with 10-bit measuring 7 positive voltages and local temperature.
Resolution The LM96080 also measures the speed of two fans
2 Programmable Fan Speed Monitoring Inputs and includes other hardware monitoring on an I2
interface. The LM96080 includes a sequencer that
2.5 mV LSb and 2.56V Input Range performs WATCHDOG window comparisons of all
Chassis Intrusion Detector Input measured values and its interrupt outputs become
WATCHDOG Comparison of All Monitored active when any values exceed the programmed
Values limits.
Separate Input to Show Status in Interrupt The LM96080 is especially suited to interface to both
Status Register of Additional External linear and digital temperature sensors. The 2.5 mV
Temperature Sensors Such as the LM26/27, LSb (least significant bit) and 2.56 volt input range is
ideal for accepting inputs from a linear sensor such
LM56/57, LM73, or LM75 as the LM94022. The BTI is used as an input from
I2C Serial Bus Interface Compatibility, either digital or thermostat sensors such as LM73,
Supports Standard Mode, 100 kbits/s, and Fast LM75, LM56, LM57, LM26, LM27, LM26LV, or other
Mode, 400 kbits/s LM96080.
Shutdown Mode to Minimize Power The LM96080 supports Standard Mode (Sm, 100
Consumption kbits/s) and Fast Mode (Fm, 400 kbits/s) I2C interface
Programmable RST_OUT/OS Pin: RST_OUT modes of operation. LM96080 includes an analog
Provides a Reset Output; OS Provides an filter on the I2C digital control lines that allows
Interrupt Output Activated by an improved noise immunity and supports TIMEOUT
Overtemperature Shutdown Event reset function on SDA and SCL that prevents I2C bus
lockup. Three I2C device address pins allow up to 8
Software and Pin Compatible with the LM80 parts on a single bus.
APPLICATIONS The LM96080's 3.0V to 5.5V supply voltage range,
low supply current, and I2C interface make it ideal for
Communications Infrastructure a wide range of applications. Operation is ensured
System Thermal and Hardware Monitoring for over the temperature range of (40)°C TA
Servers +125°C. The LM96080 is available in a 24-pin
TSSOP package.
Electronic Test Equipment and
Instrumentation
Office Electronics
KEY SPECIFICATIONS
Total Unadjusted Error ±1 %FS (Max)
Differential Non-Linearity ±1 Lsb (Max)
Supply Voltage Range +3.0 V to +5.5 V
Supply Current (Operating) 0.370 mA Typ
Supply Current (Shutdown) 0.330 mA Typ
ADC Resolution 10 Bits
Temperature Resolution 0.5°C/0.0625°C
Temperature Accuracy ±3°C (Max)
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2009–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
1
INT_IN
2SDA
3
SCL
4
FAN1
5
FAN2
6
BTI
7
GPI (CI)
8
GND
9
V+
10
INT
11
GPO
12
NTEST_IN/RESET_IN
24
23
22
21
20
19
18
17
16
15
14
13
LM96080
24-TSSOP
A2
A1
A0/NTEST_OUT
IN0
IN1
IN2
IN3
IN4
IN5
IN6
GNDA
RST_OUT/OS
Interrupt
Outputs
LM75
Temperature
Sensor
Fan Speed
Counter
General Purpose Output
(Power Switch Bypass#)
LM96080
10-bit
Sigma-Delta
ADC
Interrupt
Masking
and
Interrupt
Control
Analog
Inputs
V+
Positive
Voltage
Negative
Voltage
Chassis
Intrusion
Detector
Temperature
Sensor
Interface and Control
Serial Bus
Interface
SDA
SCL
A0/NTEST_OUT
A1
A2
GPI(CI)
Limit
Registers and
WATCHDOG
Comparators
INT
BTI
INT_IN
GPO
IN0
IN1
IN2
IN3
IN4
IN5
IN6 RST_OUT / OS
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
Typical Application
Connection Diagram
2Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
ESD
Clamp
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
PIN DESCRIPTIONS
Pin Pin ESD Type Description
Number Name(s) Structure
Interrupt Input Bar. This is an active low input that
1 INT_IN Digital Input propagates the INT_IN signal to the INT output of the
LM96080.
2 SDA Digital I/O Serial Bus Bidirectional Data. NMOS open-drain output.
3 SCL Digital Input Serial Bus Clock.
4-5 FAN1, FAN2 Digital Inputs Fan tachometer inputs.
Board Temperature Interrupt driven by Overtemperature
6 BTI Digital Input Shutdown (O.S.) outputs of additional temperature sensors
such as LM75. This pin provides internal pull-up of 10 kΩ.
General Purpose Input pin. GPI can be used as an
GPI (Chassis additional active high interrupt input pin or as an active high
7 Digital I/O
Intrusion) input from an external circuit which latches a Chassis
Intrusion event.
8 GND GROUND Internally connected to all of the digital circuitry.
+3.0V to +5.5V power. Bypass with the parallel combination
9 V+POWER of 10 μF (electrolytic or tantalum) and 0.1 μF (ceramic)
bypass capacitors.
Non-Maskable Interrupt (Active High, PMOS, open-drain) or
Interrupt Request (Active Low, NMOS, open-drain).
10 INT Digital Output Whenever INT_IN, BTI, or GPI interrupts, this output pin
becomes active.
General Purpose Output pin is an active low NMOS open
GPO (Power drain output intended to drive an external power PMOS for
11 Switch Digital Output software power control or can be utilized to control power
Bypass) to a cooling fan.
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM96080
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
PIN DESCRIPTIONS (continued)
Pin Pin ESD Type Description
Number Name(s) Structure
An active-low input that enables NAND Tree board-level
NTEST_IN/
12 Digital Input connectivity testing. Whenever NAND Tree connectivity is
RESET_IN enabled, the LM96080 resets to its power on state.
This pin is an NMOS open drain output. RST_OUT
RST_OUT/O
13 Digital Output provides a master reset to devices connected to this line.
SOS is dedicated to the temperature reading WATCHDOG.
Internally connected to all analog circuitry. The ground
reference for all analog inputs. This pin needs to be taken
14 GNDA GROUND to a low noise analog ground plane for optimum
performance.
15-21 IN6-IN0 Analog Inputs 0V to 2.56V full scale range Analog Inputs.
A0/NTEST_O The lowest order bit of the Serial Bus Address. This pin
22 Digital I/O
UT also functions as an output when doing a NAND Tree test.
23-24 A1-A2 Digital Inputs The two highest order bits of the Serial Bus Address.
4Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
LM96080
Sigma-
Delta
ADC and
MUX
0V to
2.56V
Analog
Input
Range
10-bit
2.5 mV
LSb
Interrupt
Masking
and
Interrupt
Control
Analog
Inputs
Temperature
Sensor
INTERFACE and CONTROL
GPI(CI)
Digital
Inputs
and
Outputs
IN0
Addr=20h
IN1
Addr=21h
IN2
Addr=22h
IN3
Addr=23h
IN4
Addr=24h
IN5
Addr=25h
Temperature
Addr=27h
Fan 1
Addr = 28h
Fan 2
Addr=29h
Upper Limit
Lower Limit
Upper Limit
Lower Limit
Upper Limit
Lower Limit
Upper Limit
Lower Limit
Upper Limit
Lower Limit
OS
Hysteresis
Hot
Hysteresis
Upper Limit
Upper Limit
IN0
IN1
IN2
IN3
IN4
IN5
IN6
21
20
19
18
17
16
15
FAN1
FAN2
Fan
Tach
Pulse
Inputs
Interrupt
Status
Registers
Fan Speed Counter
Fan Speed Counter
Interrupt
Outputs
Serial Bus Interface
SDASCL A0/
NTEST_OUT A1 A2
Value RAM Watchdog
4
5
1
7
6
3 2 22 23 24
11
12
13
10
IN6
Addr=26h
Upper Limit
Lower Limit
Upper Limit
Lower Limit
INT_IN
BTI
GPO
/
NTEST_IN
Reset_IN
INT
/
OS
RST_OUT
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
Block Diagram
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM96080
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
Absolute Maximum Ratings(1)(2)(3)
Supply Voltage (V+) 6.0V
Voltage on SCL, SDA, RST_OUT/OS, GPI (CI), GPO, NTEST_IN/RESET_IN, INT_IN, FAN1 and
FAN2 (0.3)V to +6.0V
Voltage on Other Pins (0.3)V to (V++ 0.3V) and 6.0V
(GND - GNDA) ±300 mV
Input Current at Any Pin(4) ±5 mA
Package Input Current(4) ±30 mA
Maximum Junction Temperature (TJmax) 150°C
ESD Susceptibility(5) Human Body Model 3000V
Machine Model 300V
Charged Device Model 1000V
Storage Temperature (65)°C to +150°C
For soldering specifications, see http://www.ti.com/lit/SNOA549(6)
(1) All voltages are measured with respect to GND, unless otherwise specified
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(4) When the input voltage (VIN) at any pin exceeds the power supplies (VIN< (GND or GNDA) or VIN>V +), the current at that pin should be
limited to 5 mA. The 30 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies
with an input current of 5 mA to six pins. Parasitic components and/or ESD protection circuitry are shown in the Pin Descriptions table.
(5) Human body model (HBM) is a charged 100 pF capacitor discharged into a 1.5 kΩresistor. Machine model (MM), is a charged 200 pF
capacitor discharged directly into each pin. Charged Device Model (CDM) simulates a pin slowly acquiring charge (such as from a
device sliding down the feeder in an automated assembler) then rapidly being discharged.
(6) Reflow temperature profiles are different for packages containing lead (Pb) than for those that do not..
Operating Ratings(1)(2)
Supply Voltage (V+) +3.0V to +5.5V
Voltage on SCL, SDA, RST_OUT/OS, GPI (CI), GPO,
NTEST_IN/RESET_IN, INT_IN, FAN1 and FAN2 (0.05)V to +5.5V
Voltage on Other Pins (0.05)V to (V++ 0.05)V and 5.5V
|GND GNDA| 100 mV
VIN Voltage Range (0.05)V to (V++ 0.05)V
Temperature Range for Electrical Characteristics (40)°C TA+125°C
Operating Temperature Range (40)°C TA+125°C
Junction to Ambient Thermal Resistance (θJA(3) )
Package Number: PW 95°C/W
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the
Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may
degrade when the device is not operated under the listed test conditions.
(2) All voltages are measured with respect to GND, unless otherwise specified
(3) The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax, θJA and the ambient temperature,
TA. The maximum allowable power dissipation at any temperature is PD= (TJmaxTA)/θJA.
6Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
DC Electrical Characteristics
The following specifications apply for +3.0 VDC V++5.5 VDC , IN0-IN6, RS= 25Ω, unless otherwise specified. Boldface
limits apply for TA= TJ= TMIN to TMAX;all other limits TA= TJ= 25°C.(1)
Typical(2) Limits(3) Units
Symbol Parameter Conditions (Limits)
POWER SUPPLY CHARACTERISTICS
V+Supply Voltage +3.3 +3.0 V (min)
+5.0 +5.5 V(max)
I+Supply Current (Interface Inactive). (See SUPPLY Round robin conversion, V+= 0.430 0.580 mA (max)
CURRENT (I+)for the I+equation). 5.5V
Round robin conversion, V+= 0.370 0.520 mA (max)
3.8V
Shutdown mode, V+= 5.5V 0.400 0.540 mA (max)
Shutdown mode, V+= 3.8V 0.330 0.480 mA (max)
TEMPERATURE-to-DIGITAL CONVERTER CHARACTERISTICS
Temperature Error (40)°C TA+125°C ±3 °C (max)
(25)°C TA+100°C ±2 °C (max)
Resolution 0.0625 °C (min)
ANALOG-to-DIGITAL CONVERTER CHARACTERISTICS
n Resolution (10 bits with full-scale at 2.56V) 2.5 mV
TUE Total Unadjusted Error See(4) ±1 % (max)
DNL Differential Non-Linearity See(5) ±1 LSb (max)
PSS Power Supply Sensitivity ±0.05 % / V
tCTotal Monitoring Cycle Time See(6) 662 ms (min)
728 810 ms (max)
MULTIPLEXER/ADC INPUT CHARACTERISTICS
RON On Resistance 2 10 kΩ(max)
ION Input Current (On Channel Leakage Current) ±0.005 μA
IOFF Off Channel Leakage Current ±0.005 μA
FAN RPM-to-DIGITAL CONVERTER
Fan RPM Error (–40)°C TA+125°C ±10 % (max)
Internal Clock Frequency (–40)°C TA+125°C 22.5 20.2 kHz (min)
24.8 kHz (max)
FAN1 and FAN2 Nominal Input Divisor = 1, Fan Count = 153(7) 8800 RPM
RPM (See FAN INPUTS)Divisor = 2, Fan Count = 153(7) 4400 RPM
Divisor = 3, Fan Count = 153(7) 2200 RPM
Divisor = 4, Fan Count = 153(7) 1100 RPM
Full-scale Count 255 (max)
DIGITAL OUTPUTS: A0/NTEST_OUT, INT
VOUT(1) Logical “1” Output Voltage IOUT = +5.0 mA at V+= +4.5V, 2.4 V (min)
IOUT = +3.0 mA at V+= +3.0V
VOUT(0) Logical “0” Output Voltage IOUT = +5.0 mA at V+= +4.5V, 0.4 V (max)
IOUT = +3.0 mA at V+= +3.0V
(1) Each input and output is protected by an ESD structure to GND, as shown in the Pin Descriptions table. Input voltage magnitude up to
0.3V above V+or 0.3V below GND will not damage the LM96080. There are parasitic diodes that exist between some inputs and the
power supply rails. Errors in the ADC conversion can occur if these diodes are forward biased by more than 50 mV. As an example, if
V+is 4.50 VDC, input voltage must be 4.55 VDC, to ensure accurate conversions.
(2) Typicals are at TJ= TA= 25°C and represent most likely parametric norm.
(3) Limits are specified to TI's AOQL (Average Outgoing Quality Level).
(4) TUE (Total Unadjusted Error) includes Offset, Gain and Linearity errors of the ADC.
(5) Limit is Specified by Design.
(6) Total Monitoring Cycle Time includes temperature conversion, 7 analog input voltage conversions and 2 tachometer readings. For more
information on the conversion rates, refer to the description of bit 0, register 07h in REGISTERS AND RAM.
(7) The total fan count is based on 2 pulses per revolution of the fan tachometer output.
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM96080
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
DC Electrical Characteristics (continued)
The following specifications apply for +3.0 VDC V++5.5 VDC , IN0-IN6, RS= 25Ω, unless otherwise specified. Boldface
limits apply for TA= TJ= TMIN to TMAX;all other limits TA= TJ= 25°C.(1)
Typical(2) Limits(3) Units
Symbol Parameter Conditions (Limits)
OPEN DRAIN OUTPUTS: GPO, RST_OUT / OS, GPI (CI)
VOUT(0) Logical “0” Output Voltage IOUT = +5.0 mA at V+= +4.5V, 0.4 V (min)
IOUT = +3.0 mA at V+= +3.0V
IOH High Level Output Current VOUT = V+0.005 1μA (max)
RST_OUT/OS, GPI (CI) Pulse Width 22.5 10 ms (min)
OPEN DRAIN SERIAL BUS OUTPUT: SDA
VOUT(0) Logical “0” Output Voltage IOUT = +3.0 mA at V+= +3.0V 0.4 V (min)
IOH High Level Output Current VOUT = V+0.005 1μA (max)
DIGITAL INPUTS: A0/NTEST_Out, A1-A2, BTI, GPI (Chassis Intrusion), INT_IN, and NTEST_IN / Reset_IN
VIN(1) Logical “1” Input Voltage 2.0 V (min)
VIN(0) Logical “0” Input Voltage 0.8 V (max)
VHYST Hysteresis Voltage V+= +3.3V 0.23 V
V+= +5.5V 0.33 V
SERIAL BUS INPUTS (SCL, SDA)
VIN(1) Logical “1” Input Voltage 0.7 × V+V (min)
VIN(0) Logical “0” Input Voltage 0.3 × V+V (max)
VHYST Hysteresis Voltage V+= +3.3V 0.67 V
V+= +5.5V 1.45 V
FAN TACH PULSE INPUTS (FAN1, FAN2)
VIN(1) Logical “1” Input Voltage 0.7 × V+V (min)
VIN(0) Logical “0” Input Voltage 0.3 × V+V (max)
VHYST Hysteresis Voltage V+= +3.3V 0.35 V
V+= +5.5V 0.5 V
ALL DIGITAL INPUTS Except for BTI
IIN(1) Logical “1” Input Current VIN = V+0.005 1μA (min)
IIN(0) Logical “0” Input Current VIN = 0 VDC 0.005 1μA (max)
CIN Digital Input Capacitance 20 pF
BTI Digital Input
IIN(1) Logical “1” Input Current VIN = V+110 μA (min)
IIN(0) Logical “0” Input Current VIN = 0 VDC, V+= +5.5 V 1 2mA
CIN Digital Input Capacitance 20 pF
8Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
AC Electrical Characteristics
The following specifications apply for +3.0 VDC V++5.5 VDC , unless otherwise specified. Boldface limits apply for TA=
TJ= TMIN to TMAX;all other limits TA= TJ= 25°C.(1)
Symbol Parameter Conditions Typical(2) Limits(3) Units
(Limits)
SERIAL BUS TIMING CHARACTERISTICS
t1SCL (Clock) Period 2.5 μs (min)
100 μs (max)
t2Data In Setup Time to SCL High 100 ns (min)
t3Data Out Stable After SCL Low 0ns (min)
t4SDA Low Setup Time to SCL Low (start) 100 ns (min)
t5SDA High Hold Time After SCL High (stop) 100 ns (min)
tTIMEOUT SCL or SDA time low for I2C bus reset 25 ms (min)
35 ms (max)
tRSDA Minimum NTEST_IN/Reset_IN rising edge to SDA falling edge 2 μs
tRSCL Minimum NTEST_IN/Reset_IN rising edge to SCL falling edge 13 μs
(1) Timing specifications are tested at the Serial Bus Input logic levels, VIN(0) = 0.3 × V+for a falling edge and VIN(1) = 0.7 × V+for a rising
edge when the SCL and SDA edge rates are similar.
(2) Typicals are at TJ= TA= 25°C and represent most likely parametric norm.
(3) Reflow temperature profiles are different for packages containing lead (Pb) than for those that do not..
Figure 1. Serial Bus Timing Diagram
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM96080
2.5 3.0 3.5 4.0 4.5 5.0 5.5
V+ (V)
TEMPERATURE ACCURACY (°C)
0.800
0.600
0.400
0.200
-2.776E-16
-0.200
-0.400
-0.600
-0.800
-1.000
-1.200
-1.400
-1.600
0.0 220.0 440.0 660.0 880.0 1.1k
CODE
TUE (% of FS)
0.040
0.018
-0.004
-0.026
-0.048
-0.070
2.5 3.0 3.5 4.0 4.5 5.0 5.5
V+ (V)
I+ (mA)
1.660
1.596
1.532
1.468
1.404
1.340
2.5 3.0 3.5 4.0 4.5 5.0 5.5
V+ (V)
I+ (mA)
0.400
0.382
0.364
0.346
0.328
0.310
2.5 3.0 3.5 4.0 4.5 5.0 5.5
V+ (V)
I+ (mA)
0.440
0.418
0.396
0.374
0.352
0.330
2.5 3.0 3.5 4.0 4.5 5.0 5.5
V+ (V)
I+ (mA)
1.330
1.290
1.250
1.210
1.170
1.130
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
The following specifications apply for +3.0 VDC V++5.5 VDC , unless otherwise specified. Boldface limits apply for TA=
TJ= TMIN to TMAX;all other limits TA= TJ= 25°C.(1)
I+vs. V+I+vs. V+(Voltage Conversion)
Figure 2. Figure 3.
I+vs. V+(Temperature Conversion) I+vs. V+(Shutdown)
Figure 4. Figure 5.
TUE Temperature Accuracy
Figure 6. Figure 7.
(1) Timing specifications are tested at the Serial Bus Input logic levels, VIN(0) = 0.3 × V+for a falling edge and VIN(1) = 0.7 × V+for a rising
edge when the SCL and SDA edge rates are similar.
10 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
FUNCTIONAL DESCRIPTION
GENERAL DESCRIPTION
The LM96080 provides 7 analog inputs, a temperature sensor, a delta-sigma ADC (Analog-to-Digital Converter),
2 fan speed counters, WATCHDOG registers, and a variety of inputs and outputs on a single chip. A two wire
Serial Bus interface is also provided. The LM96080 can perform power supply, temperature and fan monitoring
for a variety of computer systems. The LM96080 is pin and software backwards compatible with the LM80.
The LM96080 continuously converts analog inputs to 10-bit resolution with a 2.5 mV LSb (Least Significant bit)
weighting, yielding input ranges of 0 to 2.56V. The Analog Inputs, IN0 - IN6, are intended to be connected to the
several power supplies present in a typical communications infrastructure system. Temperature can be converted
to a 9-bit or 12-bit two's complement word with resolutions of 0.5°C LSb or 0.0625°C LSb, respectively.
Fan inputs can be programmed to accept either fan failure indicator or tachometer signals. Fan failure signals
can be programmed to be either active high or active low. Fan inputs measure the period of tachometer pulses
from the the fans, providing a higher count for lower fan speeds. The fan inputs are digital inputs with transition
levels according to the Fan Tach Pulse Inputs in the Electrical Characteristics table. Full scale fan counts are 255
(8-bit counter), which represent a stopped or very slow fan. Nominal speeds, based on a count of 153, are
programmable from 1100 to 8800 RPM. Signal conditioning circuitry is included to accommodate slow rise and
fall times.
The LM96080 provides a number of internal registers. These include:
Configuration Register: Provides control and configuration.
Interrupt Status Registers: Two registers to provide status of each WATCHDOG limit or Interrupt event.
Interrupt Mask Registers: Allows masking of individual Interrupt sources, as well as separate masking for
each of both hardware Interrupt outputs.
Fan Divisor/RST_OUT/OS Registers: Bits 0-5 of this register contain the divisor bits for FAN1 and FAN2
inputs. Bits 6-7 control the function of the RST_OUT/OS output.
OS Configuration/Temperature Resolution Register: The configuration of the OS (Overtemperature
Shutdown) is controlled by the lower 3 bits of this register. Bit 3 enables 12-bit temperature conversions. Bits
4-7 reflect the lower four bits of the temperature reading for a 12-bit resolution.
Conversion Rate Register: Controls the conversion rate of the round robin cycle to either continuous or 728
ms.
Voltage/Temperature Channel Disable Register: Allows voltage inputs and the local temperature
conversion to be disabled.
Value RAM: The monitoring results: temperature, voltages, fan counts, and Fan Divisor/RST_OUT/OS
Register limits are all contained in the Value RAM. The Value RAM consists of a total of 32 bytes. The first 10
bytes are all of the results, the next 20 bytes are the Watchdog Register limits, and the last two bytes are at
the upper locations for Manufacturers ID and Device Stepping/Die Revision ID.
The LM96080 is compatible with Standard Mode (Sm, 100 kbits/s) and Fast Mode (Fm, 400 kbits/s) I2C interface
modes of operation. LM96080 includes an analog filter on the I2C digital control lines that allows improved noise
immunity and supports TIMEOUT reset function on SDA and SCL that prevents I2C bus lockup. Three address
pins, A0 - A2, allow up to 8 parts on a single bus.
When enabled, the LM96080 starts by cycling through each measurement in sequence, and it continuously loops
through the sequence based on the Conversion Rate Register (address 07h) setting. Each measured value is
compared to values stored in WATCHDOG, or Limit Registers (addresses 2Ah - 2Dh). When the measured value
violates the programmed limit, the LM96080 will set a corresponding Interrupt in the Interrupt Status Registers
(addresses 01h - 02h).
Two output Interrupt lines, INT and RST_OUT/OS, are available. INT is fully programmable with masking of each
Interrupt source, and masking of each output. RST_OUT/OS is dedicated to the temperature reading
WATCHDOG registers. In addition, the Fan Divisor register has control bits to enable or disable the hardware
Interrupts.
Additional digital inputs are provided for daisy chaining the Interrupt output pin, INT. This is done by connecting
multiple external temperature sensors (i.e. LM75 or LM73) to the BTI (Board Temperature Interrupt) input and/or
the GPI (Chassis Intrusion) input. The Chassis Intrusion input is designed to accept an active high signal from an
external circuit that latches, such as when the cover is removed from the computer.
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM96080
D7 D6 D5 D4 D3 D2 D1 D0
1 9 1 9
Ack
by
Slave
Start by
Master
R/W Ack
by
Slave
Frame 1
Serial Bus Address Byte
from Master
Frame 2
Internal Address Register
Byte from Master
A2 A0A1
A3A4A5A6
SCL
SDA
Stop by
Master
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
INTERFACE
Internal Registers of the LM96080
Table 1. The internal registers and their corresponding internal LM96080 address are as follows:
Register LM96080 Internal Power on Value Notes
Address (Hex) (Binary)
Configuration Register 00h 0000 1000
Interrupt Status Register 1 01h 0000 0000
Interrupt Status Register 2 02h 0000 0000
Interrupt Mask Register 1 03h 0000 0000
Interrupt Mask Register 2 04h 0000 0000
Fan Divisor/RST_OUT/OS Register 05h 0001 0100 FAN1 and FAN2 divisor = 2 (count of 153
= 4400 RPM)
OS/ Configuration/ Temperature Resolution 06h 0000 0001
Register
Conversion Rate Register 07h 0000 0000
Voltage/Temperature Channel Disable 08h 0000 0000 Allows voltage monitoring inputs to be
Register disabled
Value RAM 20h - 29h Indeterminate Input and FAN readings
Value RAM 2Ah - 3Dh Indeterminate Limit Registers
Value RAM 3Eh 0000 0001 Manufacturer's ID
Value RAM 3Fh 0000 1000 Stepping/Die Revision ID
Serial Bus Interface/Serial Bus Timings
Figure 8. Internal Address Register Set Only
Figure 9. Internal Address Register Set with Data Byte Write
12 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
D7 D6 D5 D4 D3 D2 D1 D0
1 9 1 9
Ack
by
Slave
Start by
Master
R/W Ack
by
Slave
Frame 1
Serial Bus Address Byte
from Master
Frame 2
Internal Address Register
Byte from Master
D7 D6 D5 D4 D3 D2 D1 D0
1 9 1 9
Ack
by
Slave
No Ack
by
Master
Stop
by
Master
1 9
D15 D14 D13 D12 D11 D10 D9 D8 Ack
by
Master
Frame 3
Serial Bus Address Byte
from Master
Frame 4
Data Byte from
Slave
Frame 5
Data Byte from
Slave
R/W
A2 A0A1
A3A4A5A6
Repeat
Start by
Master
A2 A0A1A3A4A5A6
SCL
SDA
SCL
(continued)
SDA
(continued)
D7 D6 D5 D4 D3 D2 D1 D0
1 9 1 9
Ack
by
Slave
Start by
Master
R/W Ack
by
Slave
Frame 1
Serial Bus Address Byte
from Master
Frame 2
Internal Address Register
Byte from Master
D7 D6 D5 D4 D3 D2 D1 D0
1 9
Ack
by
Slave
No Ack
by
Master
Stop
by
Master
1 9
Frame 3
Serial Bus Address Byte
from Master
Frame 4
Data Byte from
Slave
R/W
A2 A0A1
A3A4A5A6
Repeat
Start by
Master
A2 A0A1A3A4A5A6
SCL
SDA
SCL
(continued)
SDA
(continued)
D7 D6 D5 D4 D3 D2 D1 D0
1 9 1 9
Ack
by
Slave
Start by
Master No Ack
by
Master
SCL
SDA Stop
by
Master
1 9
D15 D14 D13 D12 D11 D10 D9 D8 Ack
by
Master
Frame 1
Serial Bus Address Byte
from Master
Frame 2
Data Byte from
Slave
Frame 3
Data Byte from
Slave
R/W
A2 A0A1
A3A4A5A6
D7 D6 D5 D4 D3 D2 D1 D0
1 9
Ack
by
Slave
Start by
Master No Ack
by
Master
SCL
SDA
Stop
by
Master
1 9
Frame 1
Serial Bus Address Byte
from Master
Frame 2
Data Byte from
Slave
R/W
A2 A0A1
A3A4A5A6
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
Figure 10. Single Byte Read from Register with Preset Internal Address Register
Figure 11. Double Byte Read from Register with Preset Internal Address Register
Figure 12. Single Byte Read from Register with Internal Address Set using a Repeat Start
Figure 13. Double Byte Read from Register with Internal Address Set using a Repeat Start
The Serial Bus control lines include the SDA (serial data), SCL (serial clock), and A0-A2 (address) pins. The
LM96080 can only operate as a slave. The SCL line only controls the serial interface, all other clock functions
within LM96080 such as the ADC and fan counters are done with a separate asynchronous internal clock.
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM96080
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
When using the Serial Bus Interface, a write will always consists of the LM96080 Serial Bus Interface Address
byte, followed by the Internal Address Register byte, then the data byte.
There are two cases for a read:
1. If the Internal Address Register is known to be at the desired Address, simply read the LM96080 with the
Serial Bus Interface Address byte, followed by the data byte read from the LM96080.
2. If the Internal Address Register value is unknown, write to the LM96080 with the Serial Bus Interface
Address byte, followed by the Internal Address Register byte. Then restart the Serial Communication with a
Read consisting of the Serial Bus Interface Address byte, followed by the data byte read from the LM96080.
The default power on Serial Bus address for the LM96080 is 0101(A2)(A1)(A0) binary, where A0-A2 are the
Serial Bus Address.
All of the combinations of communications supported by the LM96080 are depicted in the Serial Bus Interface
Timing Diagrams as shown in Figure 13.
USING THE LM96080
Power On
When power is first applied, the LM96080 performs a “power on reset” on several of its registers. The power on
condition of registers is shown in Table 1. Registers whose power on values are not shown have power on
conditions that are indeterminate (this includes the value RAM and WATCHDOG limits). In most applications,
usually the first action after power-on would be to write WATCHDOG limits into the Value RAM.
Resets
Configuration Register INITIALIZATION bit (address 00h, bit 7) accomplishes the same function as power on
reset. The Value RAM conversion results (addresses 20h - 29h) and Value RAM WATCHDOG limits (addresses
2Ah - 3Dh) are not reset and will be indeterminate immediately after power on. If the Value RAM contains valid
conversion results and/or Value RAM WATCHDOG limits have been previously set, they will not be affected by
the Configuration Register INITIALIZATION (except for addresses 3Eh and 3Fh). Power on reset or
Configuration Register INITIALIZATION bit clear or initialize the following registers (the initialized values are
shown in Table 1):
1. Configuration Register
2. Interrupt Status Register 1
3. Interrupt Status Register 2
4. Interrupt Mask Register 1
5. Interrupt Mask Register 2
6. Fan Divisor/RST_OUT/OS Register
7. OS Configuration/Temperature Resolution Register
8. Conversion Rate Register
9. Voltage/Temperature Channel Disable Register
10. Value RAM Registers (only addresses 3Eh and 3Fh)
Configuration Register INITIALIZATION is accomplished by setting bit 7 of the Configuration Register (address
00h) high. This bit automatically clears after being set.
The LM96080 can be reset to its “power on state” by taking NTEST_IN/Reset_IN pin low for at least 50 ns.
The time it takes for NTEST_IN/Reset_IN rising edge to SDA falling edge is at least tRSDA, and for
NTEST_IN/Reset_IN rising edge to SCL falling edge is at least tRSCL. Refer to the AC Electrical Characteristics
for more information on tRSDA and tRSCL.
14 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
Using the Configuration Register
The Configuration Register (address 00h) provides control for the LM96080. At power on, the ADC is stopped
and INT_Clear (bit 3) is asserted, clearing the INT and RST_OUT/OS hardwire outputs. The Configuration
Register starts and stops the LM96080, enables and disables INT outputs, clears and sets GPI (CI) and GPO I/O
pins, initiates reset pulse on RST_OUT/OS pin, and provides the reset function described in the AC Electrical
Characteristics section.
Bit 0 of the Configuration Register, START, controls the monitoring loop of the LM96080. Setting bit 0 low stops
the LM96080 monitoring loop and puts the LM96080 in shutdown mode, reducing power consumption. Serial Bus
communication is possible with any register in the LM96080 although activity on these lines will increase
consumption current. Taking bit 0 high starts the monitoring loop, described in more detail subsequently.
Bit 1 of the Configuration Register, INT Enable, enables the INT Interrupt hardwire output when this bit is taken
high.
Bit 2 of the Configuration Register, INT Polarity Select, defines whether the INT pin is NMOS or PMOS open
drain.
Bit 3, INT_Clear, clears the INT output when taken high. The LM96080 monitoring function will stop until bit 3 is
taken low. The content of the Interrupt Status Registers (addresses 01h - 02h) will not be affected.
Bit 4, RESET, when taken high, will initiate a 10 ms RESET signal on the RST_OUT/OS output when OS Pin
Enable (address 05h, bit 6) = 0 and RST Enable (address 05h, bit 7) = 1.
When bit 5, Chassis Clear, is taken high, the GPI (Chassis Intrusion) pin is driven low for 10 ms.
Bit 6 of the configuration register, GPO, sets or clears the GPO output. This pin can be used in software power
control by activating an external power control MOSFET.
Starting Conversions
Start the monitoring function (Analog inputs, temperature, and fan speeds) in the LM96080 by writing to the
Configuration Register and setting INT_Clear (bit 3) low and Start (bit 0) high. The LM96080 then performs a
round-robin monitoring of all analog inputs, temperature, and fan speed inputs. The sequence of items being
monitored corresponds to locations in the Value RAM (except for the Temperature reading) as follows:
1. Temperature
2. IN0
3. IN1
4. IN2
5. IN3
6. IN4
7. IN5
8. IN6
9. Fan 1
10. Fan 2
Reading Conversion Results
The conversion results are available in the Value RAM (addresses 20h - 29h). Conversions can be read at any
time and will provide the result of the last conversion. If a conversion is in progress while a communication is
started, that conversion will be completed, and the internal register(s) will not be updated until the communication
is complete.
A typical sequence of events upon power on of the LM96080 would consist of:
1. Set WATCHDOG Limits
2. Set Interrupt Masks
3. Start the LM96080 monitoring process
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM96080
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
ANALOG INPUTS
The 10-bit ADC has a 2.5 mV (2.56/210) LSb , yielding a 0V to 2.5575V (2.56 - 1 LSb) input range. This is true for
all analog inputs. In most monitoring applications, these inputs would most often be connected to power supplies.
The 2.5, 3.3, ±5 and ±12 volt inputs should be attenuated with external resistors to any desired value within the
input range. Care should be taken not to exceed V+at any time.
A typical application, such as is shown in Figure 14, might select the input voltage divider to provide 1.9V at the
analog inputs of the LM96080. This is sufficiently high for good resolution of the voltage, yet leaves headroom for
upward excursions from the supply of about 25%. To simplify the process of resistor selection, set the value of
R2 first. Select a value for R2 or R4 between 10 kΩand 100 kΩ. This is low enough to avoid errors due to input
leakage currents yet high enough to protect both the inputs under overdrive conditions as well as minimize
loading of the source. Then select R1 or R3 to provide a 1.9V input as show in Figure 14.
Figure 14. Input Examples. Resistor values shown in table provide approximately 1.9V at the analog
inputs.
Table 2. VIN = 1.9V for Different R Values
Voltage Measure- R1 or R3 R2 or R4 Voltage
ments at
(VS) Analog Inputs
( ADC code 760)
+2.5V 23.7 kΩ75 kΩ+1.9V
+3.3V 22.1 kΩ30 kΩ+1.9V
+5.0V 24 kΩ14.7 kΩ+1.9V
+12V 160 kΩ30.1 kΩ+1.9V
12V 160 kΩ35.7 kΩ+1.9V
5V 36 kΩ16.2 kΩ+1.9V
For positive input voltages, the equation for calculating R1 is as follows:
R1 = [ (VSVIN) / VIN] R2 (1)
For negative input voltages, the equation for calculating R3 is as follows:
R3 = [ (VSVIN) / (VIN 5V)] R4 (2)
External resistors should be included to limit input currents to the values given in the ABSOLUTE MAXIMUM
RATINGS for Input Current At Any Pin. Inputs with the attenuator networks will usually meet these requirements.
If it is possible for inputs without attenuators to be turned on while LM96080 is powered off, additional resistors of
about 10 kΩshould be added in series with the inputs to limit the input current.
16 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
I+ = (1293 x I+TEMP) + (1116 x 7 x I+VOLTAGE) + (253037 x I+SHUTDOWN)
262,142
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
SUPPLY CURRENT (I+)
The measured supply current (I+) in the Electrical Characteristics are only for the round robin conversion and the
shutdown mode at a certain supply voltage. To calculate the supply current I+in the round robin mode at different
supply voltages, use the equation below.
(3)
The I+TEMP, I+VOLTAGE, and I+SHUTDOWN values can be obtained from the plots shown in Typical Performance
Characteristics.
LAYOUT AND GROUNDING
Analog inputs will provide best accuracy when referred to the AGND pin or a supply with low noise. A separate,
low-impedance ground plane for analog ground, which provides a ground point for the voltage dividers and
analog components, will provide best performance but is not mandatory. Analog components such as voltage
dividers should be located physically as close as possible to the LM96080.
The power supply bypass, a parallel combination of 10 μF (electrolytic or tantalum) and 0.1 μF (ceramic) bypass
capacitors connected between V+, pin 9, and ground, should also be located as close as possible to the
LM96080.
FAN INPUTS
Inputs are provided for signals from fans equipped with tachometer outputs. These are logic-level inputs set
according to the Fan Tach Pulse Inputs in the Electrical Characteristics table. Signal conditioning in the LM96080
accommodates the slow rise and fall times typical of fan tachometer outputs. The maximum input signal range is
0 to +5.5V. In the event these inputs are supplied from fan outputs which exceed 0 to +5.5V, either resistive
division or diode clamping must be included to keep inputs within an acceptable range. R2 is selected so that it
does not develop excessive error voltage due to input leakage. R1 is selected based on R2 to provide a
minimum input of 2V and a maximum of 5.5V. R1 should be as low as possible to provide the maximum possible
input up to 5.5V for best noise immunity. Alternatively, use a shunt reference or zener diode to clamp the input
level.
If fans can be powered while the power to the LM96080 is off, the LM96080 inputs must be protected to meet the
Absolute Maximum Ratings section. In most cases, open collector outputs with pull-up resistors inherently limit
this current. If this maximum current could be exceeded, either a larger pull up resistor should be used or
resistors connected in series with the fan inputs.
The Fan Inputs gate an internal 22.5 kHz oscillator for one period of the Fan signal into an 8-bit counter
(maximum count = 255). The default divisor is set to 2 (choices are 1, 2, 4, and 8) providing a nominal count of
153 for a 4400 RPM fan with two pulses per revolution. Typical practice is to consider 70% of normal RPM a fan
failure, at which point the count will be 219.
Determine the fan count according to:
(4)
For example, if the frequency of the tachometer were 150 Hz, the RPM would be 4,500 [RPM = (freq) × (60
seconds/min) / (2 pulses/revolution) ]. Since the default divisor is 2, the count would be 150 according to the
equation above.
Note that Fan 1 and Fan 2 Divisors are programmable via the Fan Divisor/RST_OUT/OS Register (address 05h).
FAN1 and FAN2 inputs can also be programmed to be level sensitive interrupt inputs.
Fans that provide only one pulse per revolution would require a divisor set twice as high as fans that provide two
pulses, thus maintaining a nominal fan count of 153. Therefore, the divisor should be set to 4 for a fan that
provides 1 pulse per revolution with a nominal RPM of 4400.
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM96080
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
Alternatives for Fan Inputs
Figure 15. Fan with Tach Pull-Up to +5V
Figure 16. Fan with Tach Pull-Up to +12V, or Totem-Pole Output and Resistor Attenuator
Figure 17. Fan with Tach Pull-Up to +12V and Diode Clamp
Figure 18. Fan with Strong Tach Pull-Up or Totem Pole Output and Diode Clamp
The table below shows example calculation for Count with different divisor and frequency. Counts are based on 2
pulses per revolution tachometer outputs.
RPM Time per Revolution Counts for “Divide by 2” Comments
(Default) in Decimal
4400 13.64 ms 153 counts Typical RPM
3080 19.48 ms 219 counts 70% RPM
2640 22.73 ms 255 counts 60% RPM
(maximum counts)
18 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
Mode Select Nominal RPM Time per Revolution Counts for the 70% RPM Time per Revolution
Given Speed in Decimal for 70% RPM
Divide by 1 8800 6.82 ms 153 6160 9.74 ms
Divide by 2 4400 13.64 ms 153 3080 19.48 ms
Divide by 4 2200 27.27 ms 153 1540 38.96 ms
Divide by 8 1100 54.54 ms 153 770 77.92 ms
TEMPERATURE MEASUREMENT SYSTEM
The LM96080 delta-VBE type temperature sensor and sigma-delta ADC perform 9-bit or a 12-bit two's-
complement conversions of the temperature. An 8-bit digital comparator is also incorporated that compares the
readings to the user-programmable Hot and Overtemperature setpoints, and Hysteresis values.
(Non-Linear Scale for Clarity)
Figure 19. 9-bit Temperature-to-Digital Transfer Function
(Non-Linear Scale for Clarity)
Figure 20. 12-bit Temperature-to-Digital Transfer Function
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM96080
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
Temperature Data Format
Temperature data can be read from the Temperature Reading Register (address 27h). Temperature limits can be
read from and written to the Hot Temperature, Hot Temperature Hysteresis, OS Temperature, and OS
Temperature Hysteresis Limit Registers (addresses 38h - 3Bh). These limits are also referred to as Thot, Thot hyst,
Tos , and Tos hyst respectively. Each limit is represented by an 8-bit, two's complement word with an LSb (Least
Significant Bit) equal to 1°C:
Temperature Digital Output
Binary Hex
+125°C 0111 1101 7Dh
+25°C 0001 1001 19h
+1.0°C 0000 0001 01h
+0°C 0000 0000 00h
1.0°C 1111 1111 FFh
25°C 1110 0111 E7h
55°C 1100 1001 C9h
By default, Temperature Reading Register is represented by a 9-bit two's complement digital word with the LSb
having a resolution of 0.5°C:
Temperature Digital Output
Binary Hex
+125°C 0 1111 1010 0 FAh
+25°C 0 0011 0010 0 32h
+1.5°C 0 0000 0011 0 03h
+0°C 0 0000 0000 0 00h
0.5°C 1 1111 1111 1 FFh
25°C 1 1100 1110 1 CEh
55°C 1 1001 0010 1 92h
Temperature Register data can also be represented by a 12-bit two's complement digital word with a LSb of
0.0625°C:
Temperature Digital Output
Binary Hex
+125°C 0111 1101 0000 7 D0h
+25°C 0001 1001 0000 1 90h
+1.0°C 0000 0001 0000 0 10h
+0.0625°C 0000 0000 0001 0 01h
0°C 0000 0000 0000 0 00h
(0.0625)°C 1111 1111 1111 F FFh
(1.0)°C 1111 1111 0000 F F0h
(25)°C 1110 0111 0000 E 70h
(55)°C 1100 1001 0000 C 90h
20 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
When using a single byte read, the 8 MSbs of the Temperature reading can be found at Value RAM (address
27h). The remainder of the Temperature reading can be found in the OS Configuration/Temperature Resolution
Register (address 06h), bits 4-7. In 9-bit format, bit 7 is the only valid bit. In addition, all 9 or 12 bits can be read
using a double byte read at register address 27h.
Temperature Interrupts
There are four Value RAM WATCHDOG limits for the Temperature reading that affect the INT and OS outputs of
the LM96080. They are: Thot, Thot hyst, Tos , and Tos hyst Limit Registers (addresses 38h - 3Bh). There are three
interrupt modes of operation: “Default Interrupt” mode, “One-Time Interrupt” mode, and “Comparator Mode”. The
OS output of the LM96080 can be programmed for “One-Time Interrupt” mode and “Comparator” mode. INT can
be programmed for “Default Interrupt” mode and “One-Time” Interrupt. These modes are explained below and
shown in Figure 21.
“Default Interrupt mode” operates in the following way: Exceeding Thot causes an Interrupt that will remain
active indefinitely until reset by reading Interrupt Status Register 1 (address 01h) or cleared by the INT_Clear bit
in the Configuration register (address 00h, bit 3). Once an Interrupt event has occurred by crossing Thot, then
reset, an Interrupt will occur again once the next temperature conversion has completed. The interrupts will
continue to occur in this manner until the temperature goes below Thot hyst, at which time the Interrupt output will
automatically clear.
“One-Time Interrupt” mode operates in the following way: Exceeding Thot causes an Interrupt that will remain
active indefinitely until reset by reading Interrupt Status Register 1 or cleared by the INT_Clear bit in the
Configuration register. Once an Interrupt event has occurred by crossing Thot, then reset, an Interrupt will not
occur again until the temperature goes below Thot hyst.
“Comparator” mode operates in the following way: Exceeding Tos causes the OS output to go Low (default).
OS will remain Low until the temperature goes below Tos hyst. Once the temperature goes below Tos hyst, OS will
go high.
A. This diagram does not reflect all the possible variations in the operation of the OS and INT outputs nor the OS and
Hot Temp bits. The interrupt outputs are cleared by reading the appropriate Interrupt Status Registers (addresses 01h
- 02h).
Figure 21. Temperature Interrupt Response Diagram
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM96080
IN0 Watchdog
Interrupt
Status
Registers
INT Mask
Registers
IN1 Watchdog
IN2 Watchdog
IN3 Watchdog
IN4 Watchdog
IN5 Watchdog
IN6 Watchdog
Temp Watchdog
Fan 1 Watchdog
Fan 2 Watchdog
Temp Watchdog
OS Polarity 06h[1]
OS Pin Enable 05h[6]
RST Enable 05h[7]
RESET 00h[4]
RST_OUT / OS
INT_Clear
00h[3] INT
Polarity
Select 00h[2]
INT
Enable
00h[1]
INT
BTI
GPI (CI)
INT_IN
OS Status 06h[0]
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
THE LM96080 INTERRUPT STRUCTURE
Figure 22. Interrupt Structure
Figure 22 depicts the Interrupt Structure of the LM96080. Note that the number next to each input of the gate
represents a register and bit address. For example, INT_Clear 00h[3] refers to bit 3, INT_Clear, of register
address 00h. The LM96080 can generate Interrupts as a result of each of its internal WATCHDOG registers on
the analog, temperature, and fan inputs.
Interrupt Inputs
External Interrupts can come from the following sources. While the label suggests a specific type or source of
Interrupt, this label is not a restriction of its usage, and it could come from any desired source:
BTI (Board Temperature Interrupt) - This is an active low Interrupt intended to come from the
Overtemperature Shutdown (O.S.) output of LM75 temperature sensors. The LM75 O.S. output goes active
when its temperature exceeds a programmed threshold. Up to 8 LM75's can be connected to a single serial
bus with their O.S. output's wire or'ed to the BTI input of the LM96080. If the temperature of any LM75
exceeds its programmed limit, BTI is driven low. This generates an Interrupt via bit 1 of the Interrupt Status
Register 2 (address 02h) to notify the host of a possible overtemperature condition. To disable this feature,
set bit 1 of the Interrupt Mask Register 2 (address 04h) high. This pin also provides an internal pull-up resistor
of 10 kΩ.
GPI (Chassis Intrusion) - This is an active high interrupt from any type of device that detects and captures
chassis intrusion violations. This could be accomplished mechanically, optically, or electrically, and circuitry
external to the LM96080 is expected to latch the event. Read this Interrupt using bit 4 of the Interrupt Status
Register 2 (address 02h), and disable it using bit 4 of the Interrupt Mask Register 2 (address 04h). The
design of the LM96080 allows this input to go high even with no power applied to the LM96080, and no
clamping or other interference with the line will occur. This line can also be pulled low for at least 10 ms by
the LM96080 to reset a typical Chassis Intrusion circuit. Accomplish this reset by setting bit 5 of Configuration
Register (address 00h) high; this bit is self-clearing.
INT_IN - This active low Interrupt provides a way to chain the INT (Interrupt) from other devices through the
LM96080 to the processor. If this pin is pulled low, then bit 7 of the Interrupt Status Register 1 (address 01h)
will go high indicating this Interrupt detection. Setting bit 1 of the Configuration Register (address 00h) will
also allow the output INT pin to go low when INT_IN goes low. To disable this feature, set bit 7 of the
Interrupt Mask Register 1 (address 03h) high.
Interrupt Outputs
All Interrupts are indicated in the two Interrupt Status Registers.
INT -an output pin, not to be confused with the input INT_IN pin. This pin becomes active whenever INT_IN,
BTI, or GPI interrupts. As described in Using the Configuration Register, INT is enabled when bit 1 of the
Configuration Register (address 00h) is set high. Bits 2 and 3 of the Configuration Register are also used to
set the polarity and state of the INT Interrupt line.
OS -dedicated to the Temperature reading WATCHDOG. In the Fan Divisor/RST_OUT/OS Register (address
22 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
05h), the OS enable bit (bit 6), must be set high and the RST enable bit (bit 7) must be set low to enable the
OS function on the RST_OUT/OS pin. OS pin has two modes of operation: “One-Time Interrupt” and
“Comparator”. “One-Time Interrupt” mode is selected by taking bit 2 of the OS Configuration/Temperature
Resolution Register (address 06h) high. If bit 2 is taken low, “Comparator” mode is selected. Unlike the OS
pin, the OS bit in Interrupt Status Register 2 (address 02h, bit 5) functions in “Default Interrupt” and “One-
Time Interrupt” modes. The OS bit can be masked to INT pin by taking bit 5 in the Interrupt Mask Register 2
(address 04h) low. A description of “Comparator”, “Default Interrupt”, and “One-Time Interrupt” modes can be
found in Temperature Data Format.
Interrupt Clearing
Reading an Interrupt Status Registers (addresses 01h - 02h) will output the contents of the Register and reset
the Register. The Interrupt Status Registers clear upon being read. When the Interrupt Status Registers clear,
the INT output pin is also cleared until the Registers are updated by the monitoring loop. The INT output pin is
cleared with the INT_Clear bit (address 00h, bit 3), without affecting the contents of the Interrupt Status
Registers. When this bit is high, the LM96080 monitoring loop will stop and will resume when the bit is low.
RST_OUT and GPO OUTPUTS
In PC applications, the open drain GPO provides a gate drive signal to an external PMOS power switch. This
external MOSFET would keep the power turned on regardless of the state of the front panel power switches
when software power control is used. In any given application, this signal is not limited to the function described
by its label. For example, since the LM96080 incorporates temperature sensing, the GPO output could also be
utilized to control power to a cooling fan. Take GPO active low by setting bit 6 in the Configuration Register
(address 00h) high.
RST_OUT is intended to provide a master reset to devices connected to this line. RST Enable, bit 7 of address
05h, is the RST_OUT/OS control bit that must be set high to enable this function. Setting bit 4, RESET, in the
Configuration Register (address 00h) high outputs a low pulse of at least 10 ms on this line, at the end of which
bit 4 in the Configuration Register automatically clears. Again, the label for this pin is only its suggested use. In
applications where the RST_OUT capability is not needed, it can be used for any type of digital control that
requires a 10 ms active low open drain output.
NAND TREE TESTS
A NAND tree is provided in the LM96080 for Automated Test Equipment (ATE) board level connectivity testing. If
the user applies a logic zero to the NTEST_IN/Reset_IN input pin, the device will be in the NAND tree test mode.
A0/NTEST_OUT will become the NAND tree output pin. To perform a NAND tree test, all pins included in the
NAND tree should be driven to 1. Beginning with IN0 and working clockwise around the chip, each pin can be
toggled and a resulting toggle can be observed on A0/NTEST_OUT. The following pins are excluded from the
NAND tree test: GNDA (analog ground), GND (digital ground), V+(power supply), A0/NTEST_OUT,
NTEST_IN/Reset_IN and RST_OUT/OS. Allow for a typical propagation delay of 500 ns.
REGISTERS AND RAM
Address Register
The bit designations for a register are as follows:
Bit Name Read/Write Description
7-0 Address Pointer Read/Write Address of RAM and Registers. See the tables below for detail.
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Address Pointer (Power On default 00h)
A7 A6 A5 A4 A3 A2 A1 A0
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 23
Product Folder Links: LM96080
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
Address Pointer Index (A7–A0)
Power On Value of Registers:
Registers and RAM A7–A0 in Hex <7:0> in Binary
Configuration Register 00h 0000 1000
Interrupt Status Register 1 01h 0000 0000
Interrupt Status Register 2 02h 0000 0000
Interrupt Mask Register 1 03h 0000 0000
Interrupt Mask Register 2 04h 0000 0000
Fan Divisor/RST_OUT/OS 05h 0001 0100
OS Configuration/Temperature Resolution 06h 0000 0001
Register
Conversion Rate Register 07h 0000 0000
Channel Disable Register 08h 0000 0000
Value RAM 20h 3Fh Register 3Eh defaults to 0000 0001
Register 3Fh defaults to 0000 1000
Configuration Register—Address 00h
Power on default <7:0> = 00001000 binary
Bit Name Read/Write Description
0 Start Read/Write A one enables startup of monitoring operations, a zero puts the part in shutdown mode.
Note: Unlike the "INT_Clear" bit, the outputs of Interrupt pins will not be cleared if the user writes a
zero to this location after an interrupt has occurred. At startup, limit checking functions and scanning
begin. Note, all limits should be set in the Value RAM before setting this bit HIGH.
1 INT Enable Read/Write A one enables the INT Interrupt output.
2 INT Polarity Read/Write A one selects an active high open source output while a zero selects an active low open drain
Select output.
3 INT_Clear Read/Write A one disables the INT output without affecting the contents of Interrupt Status Registers. The
device will stop monitoring. It will resume upon clearing of this bit.
4 RESET Read/Write A one outputs at least a 10 ms active low reset signal at RST_OUT, if bit 7 and bit 6 in the Fan
Divisor/RST_OUT/OS Register (address 05h) = 1 and = 0, respectively. This bit is cleared once the
pulse has gone inactive.
5 Chassis Clear Read/Write A one clears the GPI (Chassis Intrusion) pin. This bit clears itself after 10 ms.
6 GPO Read/Write A one drives the GPO (General Purpose Output) pin low.
7 INITIALIZATION Read/Write A one restores power on default value to the Configuration Register, Interrupt Status Registers,
Interrupt Mask Registers, Fan Divisor/RST_OUT/OS Register, the OS Configuration/Temperature
Resolution Register, Conversion Rate, Channel Disable, Manufacturers ID and Stepping/Die
revision ID registers. This bit clears itself. The power-on default is zero.
Interrupt Status Register 1—Address 01h
Power on default <7:0> = 0000 0000 binary
Bit Name Read/Write Description
0 IN0 Read Only A one indicates a High or Low limit has been exceeded.
1 IN1 Read Only A one indicates a High or Low limit has been exceeded.
2 IN2 Read Only A one indicates a High or Low limit has been exceeded.
3 IN3 Read Only A one indicates a High or Low limit has been exceeded.
4 IN4 Read Only A one indicates a High or Low limit has been exceeded.
5 IN5 Read Only A one indicates a High or Low limit has been exceeded.
6 IN6 Read Only A one indicates a High or Low limit has been exceeded.
7 INT_IN Read Only A one indicates that a Low has been detected on the INT_IN.
24 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
Interrupt Status Register 2—Address 02h
Power on default <7:0> = 0000 0000 binary
Bit Name Read/Write Description
0 Hot Temperature Read Only A one indicates a High or Low limit has been exceeded. Only “One-Time Interrupt” and
“Default Interrupt” modes are supported (see Temperature Interrupts and Interrupt Outputs).
The mode is set by bit-6 of the Interrupt Mask Register 2 (address 04h).
1 BTI Read Only A one indicates that an interrupt has occurred from the Board Temperature Interrupt (BTI)
input pin. BTI can be tied to the OS output of multiple LM75 chips.
2 FAN1 Read Only A one indicates that a fan count limit has been exceeded.
3 FAN2 Read Only A one indicates that a fan count limit has been exceeded.
4 GPI (Chassis Read Only A one indicates GPI (Chassis Intrusion) has gone high.
Intrusion)
5 OS bit Read Only A one indicates a High or a Low OS Temperature limit has been exceed. Only “One-Time
Interrupt” and “Default Interrupt” modes are supported (see Temperature Interrupts and
Interrupt Outputs). The mode is set by bit 7 of the Interrupt Mask Register 2.
6 Reserved Read Only
7 Reserved Read Only
Interrupt Mask Register 1—Address 03h
Power on default <7:0> = 0000 0000 binary
Bit Name Read/Write Description
0 IN0 Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
1 IN1 Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
2 IN2 Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
3 IN3 Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
4 IN4 Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
5 IN5 Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
6 IN6 Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
7 INT_IN Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
Interrupt Mask Register 2—Address 04h
Power on default <7:0> = 0000 0000 binary
Bit Name Read/Write Description
0 Hot Temperature Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
1 BTI Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
2 FAN1 Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
3 FAN2 Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
4 GPI (Chassis Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
Intrusion)
5 OS bit Read/Write A one disables the corresponding interrupt status bit for INT interrupt.
6 Hot Temperature Read/Write A zero selects the default interrupt mode which gives the user an interrupt if the temperature
Interrupt Mode goes above the hot limit. The interrupt will be cleared once the status register is read, but it will
Select again be generated when the next conversion has completed. It will continue to do so until the
temperature goes below the hysteresis limit.
A one selects the one time interrupt mode which only gives the user one interrupt when it goes
above the hot limit. The interrupt will be cleared once the status register is read. Another interrupt
will not be generated until the temperature goes below the hysteresis limit. It will also be cleared
if the status register is read. No more interrupts will be generated until the temperature goes
above the hot limit again. The corresponding bit will be cleared in the status register every time it
is read but may not set again when the next conversion is done. (Refer to Figure 21).
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 25
Product Folder Links: LM96080
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
Bit Name Read/Write Description
7 OS Bit Interrupt Read/Write A zero selects the default interrupt mode which gives the user an interrupt if the temperature
Mode Select goes above the OS limit. The interrupt will be cleared once the status register is read, but it will
again be generated when the next conversion has completed. It will continue to do so until the
temperature goes below the hysteresis limit.
A one selects the one time interrupt mode which only gives the user one interrupt when it goes
above the OS limit. The interrupt will be cleared once the status register is read. Another interrupt
will not be generated until the temperature goes below the hysteresis limit. It will also be cleared
if the status register is read. No more interrupts will be generated until the temperature goes
above the OS limit again. The corresponding bit will be cleared in the status register every time it
is read but may not set again when the next conversion is done. (Refer to Figure 21).
Fan Divisor/RST_OUT/OS Register —Address 05h
Power on <7:0> is 0001 0100
Bit Name Read/Write Description
0 FAN1 Mode Select Read/Write A one selects the level sensitive input mode while a zero selects Fan count mode for the FAN1
input pin.
1 FAN2 Mode Select Read/Write A one selects the level sensitive input mode while a zero selects Fan count mode for the FAN2
input pin.
2-3 FAN1 RPM Control Read/Write FAN1 Speed Control.
<3:2> = 00 - divide by 1;
<3:2> = 01 - divide by 2;
<3:2> = 10 - divide by 4;
<3:2> = 11 - divide by 8.
If level sensitive input is selected: <2> = 1 selects and active-low input (An interrupt will be
generated if the FAN1 input is Low), <2> = 0 selects an active-high input (an interrupt will be
generated if the FAN1 input is High).
4-5 FAN2 RPM Control Read/Write FAN2 Speed Control.
<5:4> = 00 - divide by 1;
<5:4> = 01 - divide by 2;
<5:4> = 10 - divide by 4;
<5:4> = 11 - divide by 8.
If level sensitive input is selected: <4> = 1 selects and active-low input (An interrupt will be
generated if the FAN2 input is Low), <4> = 0 selects an active-high input (an interrupt will be
generated if the FAN2 input is High).
6 OS Pin Enable Read/Write A one enables OS mode on the RST_OUT/OS output pin, while bit 7 of this register is set to
zero. If bits 6 and 7 of this register are set to zero, the RST_OUT/OS pin is disabled.
7 RST Enable Read/Write A one sets the RST_OUT/OS pin in the RST_OUT mode instead of the OS mode. If bits 6 and
7 of this register are set to zero, the RST_OUT/OS pin is disabled.
OS Configuration/Temperature Resolution Register—Address 06h
Power on default <7:0> = 0000 0001 binary
Bit Name Read/Write Description
0 OS Status Read only Status of the OS. This bit mirrors the state of the RST_OUT/OS pin when in the OS mode.
1 OS Polarity Read/Write A zero selects OS to be active-low, while a one selects OS to be active high. OS is an open-
drain output.
2 OS Mode Select Read/Write A one selects the one time interrupt mode for OS, while a zero selects comparator mode for
OS. (See Temperature Data Format)
3 Temperature Read/Write A zero selects the default 8-bit plus sign resolution temperature conversions, while a one
Resolution Control selects 11-bit plus sign resolution temperature conversions.
26 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
Bit Name Read/Write Description
4-7 Temp [3:0] Read/Write The lower nibble (4 LSbs) of the 11-bit plus sign temperature data:
<4> = Temp [0] (nibble LSb, 0.0625°C),
<5> = Temp [1],
<6> = Temp [2],
<7> = Temp [3] (nibble MSb, 0.5°C).
For 8-bit plus sign temperature resolution:
<7> = Temp [0] (LSb, 0.5°C)
<4:6> are undefined
Conversion Rate Register—Address 07h
Power on default <7:0> = 0000 0000 binary
Bit Name Read/Write Description
0 CR1 Read/Write Controls conversion rate:
0 = 728ms (typical)
1 = Continuous Conversion.
Note:
Each voltage channel conversion takes 3 ms typical.
Temperature conversion takes 3.6 ms typical for 9 - bit resolution and 23.5 ms typical for 12
- bit resolution.
Each fan tachometer input is monitored for 2 pulses, the time interval for two pulses is added
to the round robin time for each fan tach input that is enabled.
1-7 Reserved Read only Reserved will always report zero.
Voltage/Temperature Channel Disable Register—Address 08h
Power on default <7:0> = 0000 0000 binary
Bit Name Read/Write Description
0 IN0 Read/Write When set to "1", IN0:
conversions are skipped and disabled
value register reading will be 0
error events will be suppressed
1 IN1 Read/Write When set to "1", IN1:
conversions are skipped and disabled
value register reading will be 0
error events will be suppressed
2 IN2 Read/Write When set to "1", IN2:
conversions are skipped and disabled
value register reading will be 0
error events will be suppressed
3 IN3 Read/Write When set to "1", IN3:
conversions are skipped and disabled
value register reading will be 0
error events will be suppressed
4 IN4 Read/Write When set to "1", IN4:
conversions are skipped and disabled
value register reading will be 0
error events will be suppressed
5 IN5 Read/Write When set to "1", IN5:
conversions are skipped and disabled
value register reading will be 0
error events will be suppressed
6 IN6 Read/Write When set to "1", IN6:
conversions are skipped and disabled
value register reading will be 0
error events will be suppressed
7 Temp Read/Write When set to "1", Temperature:
conversions are skipped and disabled
value register readings will be 0
error events will be suppressed
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 27
Product Folder Links: LM96080
LM96080
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
www.ti.com
Value RAM—Address 20h–3Fh(1)
Address A7–A0 Description
20h IN0 reading (10-bit)
21h IN1 reading (10-bit)
22h IN2 reading (10-bit)
23h IN3 reading (10-bit)
24h IN4 reading (10-bit)
25h IN5 reading (10-bit)
26h IN6 reading (10-bit)
27h Temperature reading (9-bit or 12-bit for easy read-back)
28h FAN1 reading
Note: This location stores the number of counts of the internal clock per revolution.
29h FAN2 reading
Note: This location stores the number of counts of the internal clock per revolution.
2Ah IN0 High Limit
2Bh IN0 Low Limit
2Ch IN1 High Limit
2Dh IN1 Low Limit
2Eh IN2 High Limit
2Fh IN2 Low Limit
30h IN3 High Limit
31h IN3 Low Limit
32h IN4 High Limit
33h IN4 Low Limit
34h IN5 High Limit
35h IN5 Low Limit
36h IN6 High Limit
37h IN6 Low Limit
38h Hot Temperature Limit (High)
39h Hot Temperature Hysteresis Limit (Low)
3Ah OS Temperature Limit (High)
3Bh OS Temperature Hysteresis Limit (Low)
3Ch FAN1 Fan Count Limit
Note: It is the number of counts of the internal clock for the Low Limit of the fan speed.
3Dh FAN2 Fan Count Limit
Note: It is the number of counts of the internal clock for the Low Limit of the fan speed.
3Eh Manufacturer's ID always defaults to 0000 0001; this register is writable and can be reset to the default value by the
INITIALIZATION bit in the Configuration Register (address 00h, bit 7).
3Fh Stepping/Die Revision ID always defaults to 0000 1000; this register is writable and can be reset to the default
value by the INITIALIZATION bit in the Configuration Register.
(1) Setting all ones to the high limits for voltages and fans (0111 1111 binary for temperature) means interrupts will never be generated
except the case when voltages go below the low limits.
For voltage input high limits, the device is doing a greater than comparison. For low limits, however, it is doing a less than or equal to
comparison.
28 Submit Documentation Feedback Copyright © 2009–2013, Texas Instruments Incorporated
Product Folder Links: LM96080
LM96080
www.ti.com
SNAS465D SEPTEMBER 2009REVISED MARCH 2013
REVISION HISTORY
Changes from Revision C (March 2013) to Revision D Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 28
Copyright © 2009–2013, Texas Instruments Incorporated Submit Documentation Feedback 29
Product Folder Links: LM96080
PACKAGE OPTION ADDENDUM
www.ti.com 11-Apr-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish MSL Peak Temp
(3)
Op Temp (°C) Top-Side Markings
(4)
Samples
LM96080CIMT/NOPB ACTIVE TSSOP PW 24 61 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LM96080
CIMT
LM96080CIMTX/NOPB ACTIVE TSSOP PW 24 2500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LM96080
CIMT
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM96080CIMTX/NOPB TSSOP PW 24 2500 330.0 16.4 6.95 8.3 1.6 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 6-Jul-2018
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM96080CIMTX/NOPB TSSOP PW 24 2500 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 6-Jul-2018
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LM96080CIMT/NOPB LM96080CIMTX/NOPB