www.tracopower.com
DC/DC Converters
TES 2M Series, 2 Watt
Features
◆ Supplementary and reinforced insulation
◆ I/O isolation 4000 VACrms rated for
300 Vrms working voltage
◆ Unregulated device
◆ 2 x MOOP Medical safety according to
AAMI/ANSI ES 60601-1:2005(R) and
IEC/EN 60601-1 3rd edition
◆ Industrial safety to UL/IEC/EN 60950-1
◆ Ultracompact SMD-package
◆ Operating temp. range –25°C to +80°C
◆ Qualified for leadfree reflow solder
process
◆ Available in tape & reel package
◆ 3-year product warranty
Ordercode Input voltage range Output voltage Output current max. Efficiency typ.
TES 2-0511M 5 VDC 400 mA 66 %
TES 2-0512M 5.0 VDC ±10% 12 VDC 165 mA 66 %
TES 2-0513M (nominal 05 VDC) 15 VDC 133 mA 66 %
TES 2-0522M ±12 VDC ±83 mA 72 %
TES 2-0523M ±15 VDC ±66 mA 73 %
TES 2-1211M 5 VDC 400 mA 66 %
TES 2-1212M 12.0 VDC ±10% 12 VDC 165 mA 66 %
TES 2-1213M (nominal 12 VDC) 15 VDC 133 mA 66 %
TES 2-1222M ±12 VDC ±83 mA 74 %
TES 2-1223M ±15 VDC ±66 mA 75 %
TES 2-2411M 5 VDC 400 mA 66 %
TES 2-2412M 24 VDC ±10% 12 VDC 165 mA 66 %
TES 2-2413M (nominal 24 VDC) 15 VDC 133 mA 66 %
TES 2-2422M ±12 VDC ±83 mA 74 %
TES 2-2423M ±15 VDC ±66 mA 75 %
Models
The TES 2M series is range of compact 2W DC/DC-converters providing a high
I/O-isolation voltage of 4000 VAC. With a reinforced I/O-isolation system this pro-
duct is an economical solution for many applications in instrumentation, industrial
controls, medical equipment and everywhere where supplementary- or reinforced
insulation is required.
These converters are qualified for high solder temperature profiles in leadfree sol-
der processes. For automated SMD production lines the devices can be supplied
in tape & reel package. Full SMD-design with exclusive use of ceramic capacitors
ensure a very high reliability and a long product lifetime.
Page 1 of 3
IEC 60950-1
IEC 60601-1
C
B
Scheme
UL 60950 -1
ES 60601-1
www.tracopower.com
DC/DC Converters
TES 2M Series 2 Watt
Input Specifications
Input current no load 5 Vin models: 60 mA typ.
12 Vin models: 30 mA typ.
24 Vin models: 15 mA typ.
Reverse voltage protection 0.3 A max.
Recommended input fuse (slow blow) 5 Vin models: 1.0 A
12 Vin models: 0.5 A
24 Vin models: 0.2 A
Surge voltage (1 sec. max.) 5 Vin models: 9 V max.
12 Vin models: 18 V max.
24 Vin models: 30 V max.
Input filter internal capacitors
Output Specifications
Voltage set accuracy ±4 %
Voltage balance (dual output models) 1 % max.
Regulation – Input variation 1.2 % / 1 % change of Vin
– Load variation 20 – 100 % 10 % max.
12 % max. for 5 Vout models.
Ripple and noise (0–20 MHz Bandwidth) 150 mVp-p max.
Temperature coefficient ±0.02 %/K
Short circuit protection 0.5 sec. max. (automatic recovery)
Minimum load 2 % of rated max current.
Capacitive load single output models: 330 µF max.
dual output models: 100 µF max. (each output)
General Specifications
Temperature ranges – Operating –25°C to +80°C
– Storage –55°C to +125°C
– Case temperature +90°C max.
Derating 2.5 %/K above 60°C
Humidity (non condensing) 95 % rel. H max.
Reliability, calculated MTBF (MIL-HDBK-217F at +25°C, ground benign) >2.0 Mio h
Isolation voltage (50Hz, 60sec.) – Input/Output 4000 VACrms (reinforced)
Isolation test voltage (1 sec.) 6000 Vpk
Leakage current (at 240VAC, 60Hz) 2 µA max.
Isolation capacitance – Input/Output 20 pF max. (at 100KHz, 1V)
Isolation resistance – Input/Output >10 Gohm (at 500VDC)
Safety approvals IEC/EN 60950-1, IEC/EN 60601-1 3rd Edition,
ANSI/AAMI ES60601-1 and CAN/CSA-C22.2
No. 60601-1, Medical Electrical Equipment -
Part 1: General Requirements for Basic Safety
and Essential Performance
– Certification documents www.tracopower.com/overview/tes2m
Switching frequency 50 – 100 kHz (PFM)
Environmental compliance – Reach www.tracopower.com/info/reach-declaration.pdf
– RoHS directive 2011/65/EU
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
Page 2 of 3
Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
www.tracopower.com
DC/DC Converters
TES 2M Series 2 Watt
Rev. October 23, 2018
Page 3 of 3
Outline Dimensions
Pin Single Dual
1–Vin (GND) –Vin (GND)
7No con. No con.
8No con. Common
9+Vout +Vout
10 –Vout –Vout
16 +Vin +Vin
Pin-Out
Physical Specifications
Casing material plastic
Pin material phosphor bronze
Weight 3.8 g ( 0.13oz)
Lead-free reflow solder process as per J-STD-020D.01 (to find at:
www.jedec.org - free registration required)
Moisture sensivity level (MSL) level 2 as per J-STD-033B.01 (to find at:
www.jedec.org - free registration required)
Dimensions in [mm], () = Inch
Tolerances ±0.25 (±0.01)
Pin pitch tolerances ±0.05 (±0.002)
24.0
(0.94)
0.25
(0.01)
9.0
(0.35)
18.1
(0.71)
13.7
(0.54)
15.24
(0.60)
2.54
(0.10)
3.11
(0.12)
top view
178
16 10 9
0 - 4°
0.15
1.0
(0.04)
10.6
(0.42)
9.4
(0.37)
Ø1.5
(Ø 0.06) vent hole with membrane on bottom side
(to allow proper washing process)
2.8
(0.11)
13.7 (0.54)
15.24 (0.60) 2.54 (0.10)
3.11 (0.12)
1.4 (0.055) min.
2.8
(0.11)
Solder Pad Dimension
Supporting Documents: www.tracopower.com/overview/tes2m
