Clock OSC SG-210STF
Product name SG-210STF 48.000000 MHz S
Product Number / Ordering code X1G0041710078xx
Please refer to the 8.Packing information about xx (last 2 digits)
Output waveform CMOS
Pb free / Complies with EU RoHS directive
Reference weight Typ. 12 mg
1.Absolute maximum ratings
Parameter Symbol Min. Typ. Max. Unit Conditions / Remarks
Maximum supply voltage
Vcc-GND -0.3 - +4 V -
Storage temperature T_stg -40 - +125 ºC Storage as single product
Input voltage Vin -0.3 - Vcc+0.3 V ST terminal
2.Specifications(characteristics)
Parameter Symbol Min. Typ. Max. Unit Conditions / Remarks
Output frequency f0 48.000000 MHz
Supply voltage Vcc 1.6 -3.6 V-
Operating temperature T_use -20 - +70 ºC -
Frequency tolerance f_tol -25 - 25
x10-6 T_use
Current consumption Icc - - 2.6 mA No load condition Vcc = 3.6V
Stand-by current I_std - - 2.7 µA Vcc = 3.6V , ST = GND
Symmetry SYM 45 -55 %50% Vcc Level L_CMOS=<15pF
Output voltage
VOH Vcc-0.4 - - -
VOL - - 0.4 -
Output load condition L_CMOS - - 15 pF CMOS Load
Input voltage
VIH 0.8Vcc - - ST terminal
VIL - - 0.2Vcc ST terminal
Rise time
tr- - 3.5 ns
Fall time tf - - 3.5 ns
Start-up time t_str - - 3 ms t = 0 at 0.9Vcc
Jitter
tDJ - 0 - ps Deterministic Jitter Vcc=3.3V
tRJ -2.4 -ps Random Jitter Vcc=3.3V
tRMS -2.3 -ps δ(RMS of total distribution) Vcc=3.3V
tp-p -20 -ps Peak to Peak Vcc=3.3V
tacc -2.5 -ps
Phase jitter
tPJ -0.22 -ps Off set Frequency: 12kHz to 20MHz, Vcc=3.3V
Phase noise L(f) - - -
dBc/Hz -
- -91 -
dBc/Hz Off set 10Hz Vcc=3.3V
- -120 -
dBc/Hz Off set 100Hz Vcc=3.3V
- -143 -
dBc/Hz Off set 1kHz Vcc=3.3V
- -154 -
dBc/Hz Off set 10kHz Vcc=3.3V
- -158 -
dBc/Hz Off set 100kHz Vcc=3.3V
- -158 -
dBc/Hz Off set 1MHz Vcc=3.3V
Frequency aging f_age -3 - 3
x10-6 @+25ºC first year
- - - -
Accumulated Jitter(δ) n=2 to 50000
cycles
Vcc1.8V±10% : 0.2Vcc to 0.8Vcc Level,
L_CMOS=15pF
Vcc1.8V±10% : 0.2Vcc to 0.8Vcc Level,
L_CMOS=15pF
1 Page
3.Timing chart
4.Test circuit
1) Waveform observation
2) Current consumption
*Current consumption under the
disable function should be
= GND.
3) Condition
(1) Oscilloscope
· Band width should be minimum 5 times higher (wider) than measurement frequency.
· Probe earth should be placed closely from test point and lead length should be as short as possible
* Recommendable to use miniature socket. (Don’t use earth lead.)
(2) L_CMOS also includes probe capacitance.
(3) By-pass capacitor (0.01 µF to 0.1 µF) is placed closely between VCC and GND.
(4) Use the current meter whose internal impedance value is small.
(5) Power supply
· Start up time (0 %VCC to 90 %VCC) of power source should be more than 150 µs.
· Impedance of power supply should be as lowest as possible.
GND
VCC
tr
50 %VCC
t
tw
80 %VCC
20 %VCC
tf
VCC
ST
OUT
GND
swich
supply
by-pass
capacitor
Test
Point
A
VCC
ST
OUT
GND
swich
supply
by-pass
capacitor
L_CMOS
Test Point
2 Page
5.External dimensions (Unit: mm) 6.Footprint(Recommended) (Unit: mm)
7.Reflow profile
Reflow condition (Follow of JEDEC STD-020D.01)
8.Packing information
[ 1 ]Product number last 2 digits code(xx) description The recommended code is "00"
X1G0041710078xx
Code Code
01 Any Q'ty vinyl bag(Tape cut) 14 1000pcs / Reel
11 Any Q'ty / Reel 15 2000pcs / Reel
12 250pcs / Reel 00 3000pcs / Reel
Condition
Condition
Temperature[C]
60
300
250
200
150
100
50
0
ts
60sto180s
(+150Cto+200C)
Avg. Ramp-up
3C/sMax.
Ramp-down
6C/sMax.
Time[s]
120
180
240
300
360
420
480
540
600
660
720
780
Tsmin;+150C
Tsmax;+200C
TL ;+217C
+255C
tL
60sto150s
(+217Cover)
tp;20sto40s
TP ;+260C
Time +25CtoPeak
25.0
O
F123A
2.50.15
0.9
2.00.15
#2
#1
#2
#4
#3
0.80.1
#3
0.8
0.6
#1
#4
0.7
Pin map
Pin
Connection
1
ST
2
GND
3
OUT
4
VCC
Note.
ST pin = HIGH or "open" : Specified frequency output.
ST pin = LOW : Output is high impedance, oscillation stops.
1.3
Resist
C
(ex. 0.01 µF)
#1
#2
#3
#4
1.7
1.1
0.9
To maintain stable operation, provide a 0.01uF to 0.1uF by-pass
capacitor at a location as near as possible to the power source
terminal of the crystal product (between Vcc - GND).
3 Page
[ 2 ] Taping specification
Subject to EIA-481 & IEC-60286
(1) Tape dimensions
Material of the Carrier Tape : PS
Material of the Top Tape : PET+PE Unit: mm
(2) Reel dimensions
Center material : PS
Material of the Reel : PS Unit: mm
10 P: 400.1
φ1.5
+0.1
-0
2.00.1
4.00.1
φ1.0+0.1/-0
4.00.1
2.30.1
1.750.1
3.50.1
8.00.2
2.80.1
0.250.005
1.150.1
11.41.0
9.00.3
φ60.0
φ13.00.2
2.0
+0.3
-0
φ180.0
+0
-3.0
EPSON
EPSON
User direction of feed
4 Page
9.Notice
10.Contact us
www5.epsondevice.com/en/contact/
· This material is subject to change without notice.
· Any part of this material may not be reproduced or duplicated in any form or any means without the written
permission of Seiko Epson.
· The information about applied data,circuitry, software, usage, etc. written in this material is intended for
reference only.
Seiko Epson does not assume any liability for the occurrence of customer damage or infringing on any patent
or copyright of a third party.
This material does not authorize the licensing for any patent or intellectual copyrights.
· When exporting the products or technology described in this material, you should comply with the applicable
export control laws and regulations and follow the procedures required by such laws and regulations.
· You are requested not to use the products (and any technical information furnished, if any) for the development
and/or manufacture of weapon of mass destruction or for other military purposes. You are also requested that
you
would not make the products available to any third party who may use the products for such prohibited
purposes.
· These products are intended for general use in electronic equipment. When using them in specific applications
that require
extremely high reliability, such as the applications stated below, you must obtain permission from Seiko Epson
in advance.
/ Space equipment (artificial satellites, rockets, etc.)
/ Transportation vehicles and related (automobiles, aircraft, trains, vessels, etc.)
/ Medical instruments to sustain life
/ Submarine transmitters
/ Power stations and related
/ Fire work equipment and security equipment
/ Traffic control equipment
/ And others requiring equivalent reliability.
5 Page
