Plastic Infrared Emitting Diode OP290 Series Features: * * * * Choice of narrow or wide irradiance pa ern Choice of power ranges Choice of T-13/4, TO-18 or T-46 package Higher power output than GaAs at equivalent LEDs Description: Each device in this series, is a gallium aluminum arsenide infrared Light Emi ng Diode (LED) that is molded in an IRtransmissive package with a wavelength centered at 890 nm, which closely matches the spectral response of silicon phototransistors, except for OP298 (AA, AB, AC, AD), which has either an 850 nm or 875 nm center wavelength. For iden fica on purposes, each LED anode lead is longer than the cathode lead. Package T-13/4 devices include: OP290, OP291, OP292, OP294, OP295, OP296, OP297, OP299 (A, B, C) and OP297FAB, Plasc Package TO-18 or TO-46 devices include: OP293 and OP298 (A, B, C, AA, AB, AC, AD). Each OP290, OP291 and OP292 series come in three electrical parameters op ons A, B and C. The OP290 series forward current is specified under pulse condi ons up to 1.5 amps, the OP291 series forward current is specified under pulse condi ons up to 100 milliamps and the OP292 series forward current is specified under pulse condi ons up to 1 amp. The Cathode Lead length is 0.06" (1.52 mm) shorter than the Anode Lead. The silver-copper lead frame offers excellent thermal characteris cs. Each OP293 and OP298 series come in three electrical parameter op ons A, B and C. The OP293 series has an included emission angle of 60 while the OP298 series has an included emission angle of 25. The Cathode Lead length is 0.06" (1.52 mm) shorter than the Anode Lead. These devices, which come in a variety of power ranges offering a low cost replacement for TO-18 or TO-46 herme c packages. Each OP298 series come with a high irradiance output versions with four electrical parameter op ons AA, AB, AC and AD. These power op ons are in the range of 5X greater than the A, B or C op ons. The OP298 series has an included emission angle of 25. The Cathode Lead length is 0.06" (1.52 mm) shorter than the Anode Lead. These devices, which come in a variety of power ranges offering a low cost replacement for TO-18 or TO-46 herme c packages. OP294 and OP299 are designed for low-current or power-limited applica ons, such as ba ery supplies. They are similar to the OP290 and OP295, but use a smaller chip that increases output efficiency at low current levels by increasing current density. Light output can be maximized with con nuous (D.C.) forward current up to 100 mA or with pulsed forward current up to 750 mA. The Cathode Lead length is 0.06" (1.52 mm) shorter than the Anode Lead. Each OP295, OP296 and OP297 series come in three electrical parameters op ons A, B and C. The OP295 series forward current is specified under pulse condi ons up to 5 amps, the OP296 series forward current is specified under pulse condi ons up to 2 amps and the OP297 series forward current is specified under pulse condi ons up to 1 amp. The Cathode Lead length is 0.06" (1.52 mm) shorter than the Anode Lead. The OP297FAB has a reversed polarity from the OP297A, B or C. The silver-copper lead frame offers excellent thermal characteris cs. All of these devices are spectrally and mechanically matched to the OP593 and OP598 series phototransistors. Please refer to Applicaon Bullens 208 and 210 for addional design informaon and reliability (degradaon) data. Applications: * Non-contact reflec ve object sensor * Assembly line automa on RoHS * Machine automa on * Machine safety * End of travel sensor General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. (c) TT electronics plc * Door sensor * Ba ery-operated applica ons OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue D 07/2016 Page 1 Plastic Infrared Emitting Diode OP290 Series Part Number Guide -- OP290 - OP299 Series OP 2 9 X X W Optek Assembly Photodiode Output Family Maximum Forward Current 0, 5 -- 5 amps 1, 6 -- 2 amps 2, 7 -- 1 amps 3, 8 -- 200 milli-amps 4, 9 -- 750 milli-amps Electrical Specificaon Variaons: A -- Parameter A B -- Parameter B C -- Parameter C D -- Parameter D AA -- Parameter BA AB -- Parameter BB AC -- Parameter BC AD -- Parameter BD 1 T-13/4 Package OP290, OP291, OP292, OP294, OP295, OP296, OP297, OP299 2 Electrical Connec on A, B, C, D Pin # LED X=0.060" (1.52 mm) 1 Anode 2 Cathode Electrical Connec on OP297AB Pin # LED X=0.060" (1.52 mm) 1 Cathode 2 Anode TO-18, TO-46 Package OP293 & OP298 1 2 Electrical Connec on A, B, C, AA, AB, AC, AD Pin # LED X=0.060" (1.52 mm) 1 Anode 2 Cathode DIMENSIONS ARE IN: [MILLIMETERS] INCHES General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. (c) TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue D 07/2016 Page 2 Plastic Infrared Emitting Diode OP290 Series Electrical Specifications Absolute Maximum Ratings (TA = 25 C unless otherwise noted) Storage and Opera ng Temperature Range -40o C to +100o C Reverse Voltage OP290, OP292, OP294, OP295, OP297, OP299 OP291, OP293, OP296, OP298 5.0 V 2.0 V Con nuous Forward Current OP290, OP291, OP292 OP294, OP295, OP299 OP295, OP296, OP297 150 mA(1) 100 mA(1) 150 mA(1) Con nuous Forward Current, OP293, OP298 Free Air Board Mounted Full Heat Sink 100 mA 133 mA 200 mA Peak Forward Current OP290, OP295 (25 s pulse width) OP291, OP296 (100 s pulse width) OP292, OP297 (100 s pulse width) OP293, OP298 (25 s pulse width) OP294, OP299 5.0 A 2.0 A 1.00 A 2.0 A 750 mA Notes: 1. For OP290, OP291, OP292, OP295, OP296 and OP297, derate linearly 1.67 mA/ C above 25 C (free-air). When used with heat sink (see note 5), derate linearly 2.07 mA/ C above 65 C (normal use). For OP293 and OP298, when measured in free-air, derate power dissipa on linearly 1.43 mW/ C above 25 C. For OP294 and OP299, derate linearly 1.80 mW/ C above 25 C. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. (c) TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue D 07/2016 Page 3 Plastic Infrared Emitting Diode OP290 Series Electrical Specifications Absolute Maximum Ratings (TA = 25 C unless otherwise noted) Maximum Duty Cycle OP290 (25 s pulse width @ 5 A) 1.25%(1) Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] 260 C(2) Power Dissipa on, Free Air OP290, OP291, OP292, OP295, OP296, OP297 OP293, OP298 Power Dissipa on, Board Mounted OP290, OP291, OP292, op295, OP296, OP297 OP293, OP298 Power Dissipa on, Full Heat Sink OP290, OP291, OP292, OP295, OP296, OP297 OP293, OP298 333 mW(3) 142 mW(3) 533 mW(4) 200 mW(4) 1.11 W(5) 400 mW(5) Power Dissipa on OP294, OP299 180 mW Notes: 1. For OP290, OP291, OP292, OP295, OP296 and OP297, refer to graph of Maximum Peak Pulse Current vs Pulse Width. 2. For all OPs in this series, RMA flux is recommended. Dura on can be extended to 10 second maximum when soldering. A maximum of 20 grams force may be applied to the leads when flow soldering. 3. For OP290, OP291, OP292, OP295, OP296 and OP297, measured in free-air. Derate linearly 3.33 mW/ C above 25 C. 4. For OP290, OP291and OP292, mounted on 1/16" (1.6 mm) thick PCBoard with each lead soldered through 80 mil square lands 0.250" (6.35 mm) below flange of device. Derate linearly 5.33 mW/C above 62.5. For OP293 and OP298, mounted on 1/16" (1.60 mm) thick PCBoard with each lead soldered through 80 mil square lands 0.250" (6.35 mm) below flange of device. Derate power dissipa on linearly 2.00 mW/C above 25 C (normal use). For OP295, OP296 and OP297, mounted on 1/16" (1.6 mm) thick PCBoard with each lead soldered through 80 mil square lands 0.250" (6.35 mm) below flange of device. Derate linearly 5.33 mW/C above 25 C. 5. Immersed in silicone fluid to simulate infinite heat sink. For OP290, OP291 and OP292, derate linearly 11.1 mW/C above 95C. For OP293 and OP298, derate power dissipa on linearly 2.50 mW/ C above 25 C. For OP295, OP296 and OP297, derate linearly 11.1 mW/ C above 25 C. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. (c) TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue D 07/2016 Page 4 Plastic Infrared Emitting Diode OP290 Series Electrical Specifications Electrical Characteristics (TA = 25 C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS 210 180 150 - 300 - OP291A OP291B OP291C 16 13 10 - 26 - IF = 100 mA(1)(2) Measured into a 0.250" [6.35mm] aperture 0.2" (5.08 mm) from the p of the lens. OP292A OP292B OP292C 2.7 2.2 1.7 3.6 - 4.4 - IF = 20 mA(1)(2) Measured into a 0.250" [6.35mm] aperture 0.2" (5.08 mm) from the p of the lens. OP293A OP293B OP293C 16 13 10 22 - 26 - IF = 100 mA(1)(2) Measured into a 0.250" [6.35mm] aperture 0.2" (5.08 mm) from the p of the lens. Input Diode Apertured Radiant Incidence OP290A OP290B OP290C EE (APT)(2) IF = 1.50 A(1)(2) Measured into a 0.250" [6.35mm] aperture 0.2" (5.08 mm) from the p of the lens. OP294 0.50 - 1.50 IF = 5 mA(1)(2) Measured into a 0.250" [6.35mm] aperture 0.200" (5.08mm) from the p of the lens. OP295A OP295B OP295C 44 33 22 - 77 - IF = 1.50 A(1)(2) Measured into a 0.250" [6.35mm] aperture 1.129" (28.7 mm) from the p of the lens. OP296A OP296B OP296C 3.6 2.6 1.6 - 6.6 - IF = 100 mA(1)(2) Measured into a 0.250" [6.35mm] aperture 1.129" (28.7 mm) from the p of the lens. OP297FAB OP297A OP297B OP297C 2.4 0.7 0.5 0.3 1.0 - 1.3 - IF = 20 mA(1)(2) Measured into a 0.250" [6.35mm] aperture 1.129" (28.7 mm) from the p of the lens. OP298A OP298B OP298C 3.0 2.4 1.8 - 4.8 - IF = 100 mA(1)(2) Measured into a 0.250" [6.35mm] aperture 0.2" (5.08 mm) from the p of the lens. OP298AA OP298AB OP298AC OP298AD 3.5 3.5 6.5 8.5 - 8.5 11.5 - IF = 100 mA(1)(2) Measured into a 0.250" [6.35mm] aperture 1.129" (28.7 mm) from the p of the lens. 0.45 IF = 100 mA(1)(2) Measured into a 0.250" [6.35mm] aperture 1.129" (28.7 mm) from the p of the lens. OP299 0.15 - mW/cm2 Notes: 1. Measurement is taken at the end of a single 100 s pulse. Hea ng due to increased pulse rate or pulse width will cause a decrease in reading. 2. Measurement of the average apertured radiant energy incident upon a sensing area 0.250" (6.35 mm) in diameter perpendicular to and centered on the mechanical axis of the lens and the specified distance from the end of the device. On all models in this series, EE(APT) is not necessarily uniform within the measured area. 3. Measurement is taken at the end of a single 10 ms pulse. Hea ng due to increased pulse rate or pulse width will cause a decrease in reading. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. (c) TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue D 07/2016 Page 5 Plastic Infrared Emitting Diode OP290 Series Electrical Specifications Electrical Characteristics (TA = 25 C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX VF Forward Voltage(3) OP290, OP295 OP291, OP296 OP292, OP297, OP297FAB OP293, OP298 (A, B, C) OP298 (AA, AB, AC, AD) OP294, OP299 - - 4.00 2.00 1.75 2.00 2.00 1.50 IR Reverse Current(3) OP290, OP292 OP291, OP293, OP298 (A, B, C), OP296 OP298 (AA, AB, AC, AD) OP294, OP299 OP295, OP297 OP297FAB - - 10 100 100 10 10 15 - 890 - UNITS TEST CONDITIONS Input Diode P Wavelength at Peak Emission OP290, OP291, OP292, OP293, OP294, OP295, OP296, OP297, OP298 (A, B, C), OP299 OP297FAB, OP298 (AA, AB, AC, AD) V A IF = 1.50 A IF = 100 mA IF = 20 mA IF = 1.50 A IF = 100 mA IF = 5 mA VR= 5 V VR= 2 V VR= 2 V VR= 2 V VR= 5 V VR= 5 V nm IF = 10 mA IF = 10 mA - 875 - Spectral Bandwidth between Half Power Points - 80 - nm Spectral Shi with Temperature - +0.18 - nm/C IF = Constant Emission Angle at Half Power Points OP290, OP291, OP292, OP294 OP293 OP295, OP296, OP297, OP299 OP298 - 50 60 20 25 - Degree IF = 20 mA tr Output Rise Time - 500 - ns tf Output Fall Time - 250 - ns B P /T HP General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. (c) TT electronics plc IF(PK)=100 mA, PW=10 s, and D.C.=10.0% OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue D 07/2016 Page 6 Plastic Infrared Emitting Diode OP290 Series Performance OP290, OP291, OP292, OP293, OP294, (A, C) Optical Power vs Forward Current vs Temperature Forward Voltage vs Forward Current vs Temp. 1.8 3.5 -40 C -20 C 0 C 20 C 40 C 60 C 80C 100C 1.6 -40 C -20 C 0 C 3.0 40 C 60 C 80 C 100C Relative Output Power 2.5 Forward Voltage (V) Normalized at 50 mA and 20C 20 C 1.4 1.2 2.0 1.5 1.0 1.0 0.5 0.0 0.8 0 Forward Current (mA) 40 50 60 70 Forward Current (mA) Distance vs Output Power vs Forward Current Relative Radiant Intensity vs. Angular Displacement 10 20 30 40 50 60 70 80 90 0 100 10 20 30 80 90 100 1.0 6 Normalized at 1" and 50 mA 0.9 5 0.8 10 mA 20 mA 30 mA 40 mA 50 mA 60 mA 70 mA 80 mA 90 mA 100 mA 4 3 2 Relative Radiant Intensity Normalized Output Power Forward Current 0.7 0.6 0.5 0.4 0.3 0.2 1 0.1 0 0.0 0.2 '' 0.4 '' 0.6 '' 0.8 '' 1.0 '' 1.2 '' 1.4 '' 1.6 '' 1.8 '' 2.0 '' Distance (inches) General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. (c) TT electronics plc -80 -60 -40 -20 0 20 40 60 80 Angular Displacement (Degrees) OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue D 07/2016 Page 7 Plastic Infrared Emitting Diode OP290 Series Performance OP295, OP296, OP297, OP298, OP299 Forward Voltage vs Forward Current vs Temp. Optical Power vs IF vs Temperature 1.8 3.5 -60 C -40 C -20 C 0 C 20 C 40 C 60 C 80 C 100 C 120 C 1.7 3.0 1.6 Normalized Optical Power Typical Forward Voltage (V) 2.5 1.5 1.4 1.3 1.2 -60 C -40 C -20 C 0 C 20 C 40 C 60 C 80 C 100 C 120C 1.1 1.0 0.9 0 10 20 30 40 50 60 70 80 2.0 1.5 1.0 0.5 0.0 90 0 100 10 20 30 40 50 60 70 80 90 100 Forward Current IF (mA) Forward Current (mA) Relative Radiant Intensity vs. Angular Displacement Distance vs Output Power vs Forward Current 1.0 6 Normalized at 1" and 50 mA 0.9 5 0.8 Forward Current Normalized Output Power Normalized at 50 mA and 20 C 10 mA 20 mA 30 mA 40 mA 50 mA 60 mA 70 mA 80 mA 90 mA 100 mA 4 3 2 ty is n e t In t n a i d a R e v it a l e R 0.7 0.6 0.5 0.4 0.3 0.2 1 0.1 0.0 0 0.2 '' 0.4 '' 0.6 '' 0.8 '' 1.0 '' 1.2 '' 1.4 '' 1.6 '' 1.8 '' 2.0 '' Distance (inches) General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. (c) TT electronics plc -40 -30 -20 -10 0 10 20 30 40 Angular Displacement (Degrees) OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue D 07/2016 Page 8 Plastic Infrared Emitting Diode OP290 Series Performance OP290A/OP593 and OP295/OP598 - Coupling Characteriscs Coupling Characteristics 1.2 Test Conditions: OP290 & OP295 IF = 1.5A, PW = 100s, Duty Cycle = 0.1% OP593 & OP598 VCE = 5V, RL = 1k, T A = 25C Normalized Collector Current (mA) 1.0 0.8 0.6 0.4 OP290A OP295 0.2 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Lens Tip Separation (inches) General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics' own data and is considered accurate at time of going to print. (c) TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue D 07/2016 Page 9 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Optek: OP291A OP292A OP292B OP292C OP294 OP296A OP296C OP297A OP297B OP297C OP299 OP297AB TT Electronics: OP291B OP293B OP293C OP298AA OP298AB OP298AC OP298AD OP298C