19-4497; Rev 0; 7/09 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices Features The MAX8904 power-management IC provides a complete power-supply solution for 2-cell Li+ handheld/Li-Poly applications such as point-of-sale terminals, digital SLR cameras, digital video cameras and ultra-mobile PCs. The MAX8904 includes five step-down converters (1V2, 1V8, 3V3, 5V0, and ADJ) with internal MOSFETs and +1%/-3% accurate output voltages for processor core, memory, I/O, and other system power rail requirements. LCD backlighting is supported by a WLED boost converter that can provide 35mA for up to 8 WLEDs. This boost converter is also configurable as a 6-bit programmable voltage source that can provide up to 63mA of output current. A 500mA, internal MOSFET, current-limited switch (CLS), allows system designers to control input power to external peripheral devices. o 3.4V to 13.2V Input Voltage Range o 1MHz, Up to 90% Efficient, Synchronous DC-DC Step-Down Converters o Power Converters 1V2, 1V8, and ADJ Operated Out-of-Phase with Respect to 3V3 and 5V0 o 667kHz Step-Up Converter Provides Up to 32V Output for Driving Up to Eight WLEDs o Internal Compensation on All Power Converters o Fast Line and Load Transient Responses o Internal Soft-Start and Short-Circuit Protection on All Power Converter Outputs o Input Overvoltage and Reverse Polarity Protection o 250ms Fault Timer-Based Protection for Overload, Short Circuit o I2C Serial Interface for On/Off Control, Output Voltage, WLED Current, GPIO Setting, Fault Monitoring o < 15A Standby Current Over Operating Voltage Range and Temperature o Compact, 56-Pin, 7mm x 7mm TQFN Package The MAX8904 controls an external n-MOSFET for input overvoltage protection (13.5V, typ) and an external p-MOSFET for reverse polarity protection (up to -28V) of downstream circuits. System input current monitoring for power management is facilitated by an on-board current-sense amplifier (CSA) with differential inputs and a 1.2V full scale, ground-referenced analog output. A 400kHz, I2C interface supports output voltage setting of the ADJ power rail and boost regulator (voltage source mode), WLED current setting for the boost regulator (WLED current regulator mode), GPIO control, and enable/disable of ADJ, 5V0, boost regulator, CSA blocks. The I2C interface also enables the host processor to read on-board fault status registers when interrupted by the MAX8904 FLT pin under system fault conditions. An emergency shutdown input, SHDN allows converters preselected through I 2C to turn off immediately under power-fail conditions, thus saving valuable firmware execution time. An uncommitted, active-low, 14V open-drain comparator (CMP) with a 1.25V internal reference is also provided in the MAX8904. The MAX8904 PWREN logic input turns on the 1V2, 1V8, 3V3, and 5V0 default power rails. The MAX8904 is available in a 56-pin, 7mm x 7mm TQFN package. Applications Point-of-Sale Terminals Digital Video Cameras Digital SLR Cameras Ultra-Mobile PCs Ordering Information PART MAX8904ETN+T TEMP RANGE PIN-PACKAGE -40C to +85C 56 THIN QFN-EP* (7mm x 7mm) +Denotes a lead(Pb)-free/RoHS-compliant package. *EP = Exposed pad. T = Tape and reel. Typical Operating Circuit VIN CS- MAX8904 VEXT VIN ADJLX1 ADJLX2 LVROUT BSTLX 5V0LX 1.2V, 600mA 1.8V, 975mA 3.3V, 1250mA 5V, 800mA 3.0V TO 5.067V, 1500mA VIN LVRIN5V VIN PWREN CLSIN CLSOUT CMPI CMPO SDA SCL SHDN Pin Configuration appears at end of data sheet. 1V2LX 1V8LX 3V3LX CS+ CSOUT OVGATE OVPWR RPGATE LVRPWR FLT PCS GPIO0 1mA TO 63mA UP TO 8 WLEDs 8-BIT GPIO PORT GPIO7 GND ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX8904 General Description MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices ABSOLUTE MAXIMUM RATINGS OVPWR to GND......................................................-0.3V to +30V RPGATE to GND.....................................................-0.3V to +17V OVPWR to RPGATE................................................-0.3V to +22V OVGATE to CS+ .......................................................-0.3V to +6V BSTFB to GND........................................................-0.3V to +40V BSTLX to Exposed Pad (EP) ..................................-0.3V to +40V BSTSW to BSTIN ....................................................-16V to +0.3V LVRPWR, BSTIN, BSTSW, 1V2IN, 3V3IN, 1V8IN, ADJIN, 5V0IN, CMPO, CLSIN to EP...............................-0.3V to +16V GPIO_ to EP..............................................................-0.3V to +6V CS+, CS- to GND ...................................................-0.3V to +16V CS+ to CS- ............................................................-0.3V to +0.3V CLSOUT to GND ....................................-0.3V to (VCLSIN + 0.3V) LVROUT to GND.................................-0.3V to (VLVRPWR + 0.3V) 1V2FB, 1V8FB, 3V3FB, 5V0FB, ADJFB, REF, CSOUT, CMPI to GND .................................-0.3V to (VLVRIN5V + 0.3V) 1V2BST to 1V2LX, 1V8BST to 1V8LX, 3V3BST to 3V3LX, 5V0BST to 5V0LX, ADJBST to ADJLX_................-0.3V to +6V LVRIN5V, LVROUT, SHDN, PWREN, FLT, SDA, SCL, GPIOPWR to GND ...............................................-0.3V to +6V PCS to GND ...........................................-0.3V to (VBSTIN + 0.3V) EP to GND .............................................................-0.3V to +0.3V GPIOPWR to LVRIN5V..............................................-6V to +0.3V LVROUT to LVRIN5V .............................................-0.3V to +0.3V ADJLX_, 5V0LX, 3V3LX, 1V8LX, 1V2LX, BSTLX (Note 1)........................................................1.7ARMS Continuous Power Dissipation (TA = +70C) 56-Pin TQFN-EP Single-Layer PCB (derate 27.8mW/C above +70C) ............................2222mW 56-Pin TQFN-EP Multilayer PCB (derate 40mW/C above +70C) ...............................3200mW Junction-to-Case Thermal Resistance (JC) (Note 2) .....0.8C/W Junction-to-Ambient Thermal Resistance (JA) (Note 2) Single-Layer PCB ........................................................36C/W Multilayer PCB .............................................................25C/W Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C Note 1: _LX pins have internal clamp diodes to _IN and EP. Applications that forward bias these diodes should take care not to exceed the device's power-dissipation limits. Note 2: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (V_IN = 7.2V, EP = GND, VPWREN = 5V, _LX unconnected, CREF = 0.1F; when V_IN is specified, it implies all _IN pins; TA = -40C to +85C. Typical values are at TA = +25C, unless otherwise noted. Limits are 100% production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design and characterization.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS COMMON BLOCKS Input Operating Supply Range Input Standoff Voltage V_IN V_IN falling, OVP circuit not used 3.6 14 V_IN rising, OVP circuit not used 5.8 14 V_IN falling, OVP circuit used 3.6 12.8 V_IN rising, OVP circuit used 5.8 13.2 VOVPWR 28 Standby Mode Supply Current I_IN + ILVRPWR + ICS_ V_IN = 13.2V; all channels off 5.5 Quiescent Supply Current (CH7 + CH2 + CH3 + CH4 Only) IQLVRPWR + I1V2IN + I1V8IN + I3V3IN + I5V0IN + I5V0FB No switching, V1V2FB = 1.3V, V1V8FB = 1.9V, V3V3FB = 3.4V, V5V0FB = 5.1V 100 2 _______________________________________________________________________________________ V V A 165 A High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices (V_IN = 7.2V, EP = GND, VPWREN = 5V, _LX unconnected, CREF = 0.1F; when V_IN is specified, it implies all _IN pins; TA = -40C to +85C. Typical values are at TA = +25C, unless otherwise noted. Limits are 100% production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design and characterization.) PARAMETER SYMBOL REF Output Voltage VREF OSC Frequency fOSC CONDITIONS IREF = 0A MIN 1.240 IREF = 10A TYP MAX 1.250 1.260 1.249 UNITS V 0.9 1 1.1 MHz LVROUT Output Voltage 5.4V < VLVRPWR < 14V 4.9 5.1 5.3 V LVRPWR Undervoltage Lockout Threshold VLVRPWR rising 5.3 5.55 5.8 VLVRPWR falling 3.2 3.4 3.6 LVRIN5V Undervoltage Lockout Threshold VLVRIN5V rising 3.45 VLVRIN5V falling 2.6 SHDN Input High Voltage VIH 3V < VLVRIN5V < 5.5V SHDN Input Low Voltage VIL 3V < VLVRIN5V < 5.5V V V 1.6 V 0.5 V SHDN Pullup Resistance to LVRIN5V 1 M SHDN Pulldown Resistance to GND 2 M PWREN Input High Voltage VIH 3.4V < VLVRPWR < 14V PWREN Input Low Voltage VIL 3.4V < VLVRPWR < 14V 1.6 PWREN Pulldown Resistance 1 PWREN Deglitch Delay FLT Output-Voltage Low Rising VFLT FLT Open-Drain Leakage Current FAULT Timer Delay V 0.5 10 IFLT = 20mA VFLT = 5.5V 0 0.01 TA = +85C 0.1 tFAULT Overtemperature Warning Flag s 0.4 TA = +25C 0.1 250 Rising (Note 3) (bit D3 of register 0Dh) 110 Overtemperature Warning Flag Hysteresis 120 (Note 3) 140 VOVPWR rising VOVPWR falling V A ms 130 10 Thermal Shutdown Latch Threshold V M C C 152 165 3.75 4 4.25 2.7 2.85 3.0 C INPUT VOLTAGE PROTECTION OVPWR Undervoltage Lockout Threshold OVPWR_UVLO_Rising to OVGATE Startup Delay OVP Threshold tSTARTUP VOVP OVGATE Charge Current OVGATE Discharge Resistance VOVPWR > VOVPWR_UVLO_RISING VOVPWR rising Hysteresis IOVGATE_CHG VOVGATE = 7.2V RDCHG RPGATE Pulldown Resistor RRPGATE RPGATE Clamp Voltage VCLAMP VCS+ = 14.1V, VOVGATE = 15.1V 14V VOVPWR 28V 32 13.3 13.65 V ms 14 0.17 10 V A 40 50 k 16 19 V _______________________________________________________________________________________ 3 MAX8904 ELECTRICAL CHARACTERISTICS (continued) MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices ELECTRICAL CHARACTERISTICS (continued) (V_IN = 7.2V, EP = GND, VPWREN = 5V, _LX unconnected, CREF = 0.1F; when V_IN is specified, it implies all _IN pins; TA = -40C to +85C. Typical values are at TA = +25C, unless otherwise noted. Limits are 100% production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design and characterization.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 300 425 m_ 600 mA CH1 (CURRENT-LIMITED SWITCH) Current-Limited Switch On-Resistance RONCLS ICLS = 400mA 200 Current Limit ILIMCLS VCLSIN = 12V, VCLSOUT = 9V 450 Overcurrent Fault Latch-Off Delay tOLFLT Fault Voltage VACT Thermal Loop Threshold CLSOUT Leakage Current THMTH ICLSOUTLKG VCLSIN - VCLSOUT > 1V, 150mV hysteresis Current-limit-foldback temperature threshold (Note 3) VCLSIN = 14V, VCLSOUT = 0 110 250 ms 1 V 120 130 TA = +25C 0.01 1 TA = +85C 0.1 C A CH2 (1V8 STEP-DOWN CONVERTER) Output Voltage V1V8FB Operating Frequency f1V8LX No load 1.800 Load Regulation Line Regulation V1V8IN = 3.4V to 14V Idle-Mode Trip Level (Note 4) 1V8LX Leakage Current V1V8LX = 0, 14V, V1V8IN = 14V 1V8BST Leakage Current I1V8LXLKG I1V8BSTLKG Low-Side Switch On-Resistance RONLS1V8 High-Side Switch On-Resistance RONHS1V8 High-Side Switch Current Limit ILIMHS1V8 V1V8BST = 5V + V1V8IN Output-OK (1V8OK) Fault Blanking Time After Soft-Start Done 4 -5 1 MHz %/A 0.04 %/V 0.01 TA = +85C 0.1 TA = +25C 0.01 TA = +85C 0.1 mA +5 0.1 1.43 10 (Bit D3 of register 0Fh) PWREN = GND Rising 94 Falling 90 A A _ 0.27 1.3 V -2.5 0.185 Soft-Start Rate LX Discharge Resistance 1.836 150 TA = +25C Low-Side Switch Turn-Off Current Output-OK (1V8OK) Threshold 1.818 _ 1.6 A mA % 1 V/ms 350 _ 2 ms _______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices (V_IN = 7.2V, EP = GND, VPWREN = 5V, _LX unconnected, CREF = 0.1F; when V_IN is specified, it implies all _IN pins; TA = -40C to +85C. Typical values are at TA = +25C, unless otherwise noted. Limits are 100% production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design and characterization.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 3.349 3.383 3.416 V CH3 (3V3 STEP-DOWN CONVERTER) Output Voltage V3V3FB Operating Frequency f3V3LX No load Load Regulation Line Regulation V3V3IN = 3.4V to 14V Idle-Mode Trip Level (Note 4) 3V3LX Leakage Current 3V3BST Leakage Current I3V3LXLKG I3V3BSTLKG V3V3LX = 0, 14V, V3V3IN = 14V V3V3BST = 5V + V3V3IN 1 MHz -1.1 %/A 0.04 %/V 150 TA = +25C -5 0.01 TA = +85C 0.1 TA = +25C 0.01 TA = +85C 0.1 Low-Side Switch On-Resistance RONLS3V3 0.185 High-Side Switch On-Resistance RONHS3V3 0.185 High-Side Switch Current Limit ILIMHS3V3 1.8 Low-Side Switch Turn-Off Current 2 mA +5 0.1 Output-OK (3V3OK) Threshold (Bit D4 of register 0Fh) 94 Falling 90 A _ _ 2.2 10 Rising A A mA % Maximum Duty Cycle 95 % Soft-Start Rate 1 V/ms 175 _ 2 ms LX Discharge Resistance PWREN = GND Output-OK (3V3OK) Fault Blanking Time After Soft-Start Done CH4 (5V0 STEP-DOWN CONVERTER) Output Voltage V5V0FB Operating Frequency f5V0LX No load 5.000 Load Regulation Line Regulation V5V0IN = 5.4V to 14V Idle-Mode Trip Level (Note 4) V5V0LX = 0, 14V, V5V0IN = 14V 5V0LX Leakage Current I5V0LXLKG 5V0BST Leakage Current I5V0BSTLKG V5V0BST = 5V + V5V0IN 5.050 -1.25 %/A 0.04 %/V 60 TA = +25C -5 +0.01 TA = +85C 0.1 TA = +25C 0.01 TA = +85C 0.1 RONLS5V0 0.27 High-Side Switch On-Resistance RONHS5V0 0.27 High-Side Switch Current Limit ILIMHS5V0 1.26 V MHz Low-Side Switch On-Resistance Low-Side Switch Turn-Off Current 5.100 1 1.4 10 mA +5 0.1 A A _ _ 1.54 A mA _______________________________________________________________________________________ 5 MAX8904 ELECTRICAL CHARACTERISTICS (continued) MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices ELECTRICAL CHARACTERISTICS (continued) (V_IN = 7.2V, EP = GND, VPWREN = 5V, _LX unconnected, CREF = 0.1F; when V_IN is specified, it implies all _IN pins; TA = -40C to +85C. Typical values are at TA = +25C, unless otherwise noted. Limits are 100% production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design and characterization.) PARAMETER SYMBOL Output-OK (5V0OK) Threshold CONDITIONS (Bit D5 of register 0Fh) MIN 94 Falling 90 Soft-Start Rate LX Discharge Resistance TYP Rising PWREN = GND Output-OK (5V0OK) Fault Blanking Time After Soft-Start Done MAX UNITS % 1 V/ms 350 _ 2 ms CH5 (ADJ STEP-DOWN CONVERTER) Quiescent Supply Current (IQLVRPWR No switching (CH5 only), VADJFB = 4V, + I5V0FB) + ADJSP register = 1Fh IADJIN Output Voltage Adjust Range VADJFB Operating Frequency fADJLX_ Output Voltage Accuracy 65 3 100 5.067 1 No load -1 Load Regulation 0 +1 0.04 %/V Idle-Mode Trip Level (Note 4) ADJLX_ Leakage Current IADJLX_ VADJLX = 0, 14V, VADJIN = 14V TA = +25C TA = +85C 0.1 ADJBST Leakage Current IADJBSTLKG VADJBST = 5V + VADJIN TA = +25C 0.01 TA = +85C 0.1 Low-Side Switch On-Resistance RONLSADJ High-Side Switch On-Resistance RONHSADJ High-Side Switch Current Limit ILIMHSADJ 180 0.01 mA +5 0.1 0.185 3.0 (Bit D6 of register 0Fh) Rising 94 Falling 90 Soft-Start Rate LX Discharge Resistance ADJEN = logic 0 (bit D3 of register 07h) Output-OK (ADJOK) Fault Blanking Time After Soft-Start Done A _ 3.3 10 Output-OK (ADJOK) Threshold A _ 0.185 Low-Side Switch Turn-Off Current % %/A Line Regulation 2.7 V MHz -0.75 VADJIN = 5.4V to 14V, VADJFB = 4V, ADJSP register = 1Fh -5 A A mA % 1 V/ms 175 _ 2 ms 100 A CH6 (BST STEP-UP CONVERTER) Quiescent Supply Current IQLVRPWR + IBSTIN No switching (CH6 only), BSTIV = logic 1 (bit D4 of register 09h), VBSTFB = 14V, BSTVSP register (0Ch) = 0Fh Current mode 17.4 33.5 Voltage mode (typical DAC codes) 12.5 18.7 Overvoltage Protection Range Current mode (typical DAC codes) 17.4 36 V Overvoltage Protection Accuracy Current mode, VBSTFB = 26.7V -3 +3 % Typical Output Voltage Range 6 VBSTFB _______________________________________________________________________________________ V High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices (V_IN = 7.2V, EP = GND, VPWREN = 5V, _LX unconnected, CREF = 0.1F; when V_IN is specified, it implies all _IN pins; TA = -40C to +85C. Typical values are at TA = +25C, unless otherwise noted. Limits are 100% production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design and characterization.) PARAMETER SYMBOL Output Voltage Accuracy Operating Frequency CONDITIONS Voltage mode, BSTVSP register (0Ch) = 10h MIN TYP -3 fBSTLX MAX +3 667 Minimum Duty Cycle PCS Current Accuracy IPCS PCS Leakage Current IPCSLKG BSTCSP register (0Bh) = 20h % kHz 10 Maximum Duty Cycle UNITS % 90 93 97 TA = +25C 31.04 32 32.96 TA = -40C to +85C 30.4 33.6 mA TA = +25C 0.01 TA = +85C 0.1 VBSTSW = 0, VBSTIN TA = +25C = 14V, BSTEN = IBSTSWLKG logic 0 (bit D4 of TA = +85C Register 09h) TA = +25C IBSTLXLKG VBSTLX = 0 to 36V TA = +85C 0.01 BSTSW Switch On-Resistance RONBSTSW 0.1 _ BSTLX Switch On-Resistance RONBSTLX 0.3 _ BSTSW Switch Short-Circuit Current Limit ILIMBSTSW 1.35 A BSTLX Switch Current Limit ILIMBSTLX 1.13 A BSTSW Leakage Current BSTLX Leakage Current Output Voltage OK (BSTOK) Threshold VPCS = 0 to LVRIN5V (Bit D7 of register 0Fh) 1 % 5 A 0.1 0.01 5 1 Rising, voltage mode only 95 Falling, voltage mode only 90 A A % Soft-Start Time Voltage mode and current mode 4.096 ms BSTOK Fault Blanking Time After Soft-Start Done Voltage mode and current mode 1.024 ms CH7 (1V2 STEP-DOWN CONVERTER) Output Voltage V1V2FB Operating Frequency f1V2LX No load 1.200 Load Regulation 1.212 1.224 V 1 MHz -2.5 %/A Line Regulation V1V2IN = 3.4V to 14V 0.04 %/V Idle-Mode Trip Level (Note 4) 200 mA 1V2LX Leakage Current I1V2LXLKG V1V2LX = 0, 14V, V1V2IN = 14V TA = +25C TA = +85C -5 0.01 0.1 1V2BST Leakage Current I1V2BSTLKG V1V2BST = 5V + V1V2IN TA = +25C 0.01 TA = +85C 0.1 +5 0.1 A A _______________________________________________________________________________________ 7 MAX8904 ELECTRICAL CHARACTERISTICS (continued) MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices ELECTRICAL CHARACTERISTICS (continued) (V_IN = 7.2V, EP = GND, VPWREN = 5V, _LX unconnected, CREF = 0.1F; when V_IN is specified, it implies all _IN pins; TA = -40C to +85C. Typical values are at TA = +25C, unless otherwise noted. Limits are 100% production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design and characterization.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Low-Side Switch On-Resistance RONLS1V2 0.185 _ High-Side Switch On-Resistance RONHS1V2 0.27 _ High-Side Switch Current Limit ILIMHS1V2 1.08 Low-Side Switch Turn-Off Current 1.2 1.32 10 (Bit D2 of register 0Fh) Output-OK (1V2OK) Threshold Rising 94 Falling 90 Soft-Start Rate LX Discharge Resistance PWREN = GND Output-OK (1V2OK) Fault Blanking Time After Soft-Start Done A mA % 1 V/ms 175 _ 2 ms CSA (CURRENT-SENSE AMPLIFIER) Differential Input Range VCS+ - VCS- Maximum CSOUT Output Capacitive Load CLOAD CSOUT Pulldown Resistor RPD VLVRPWR = VCS- = 5.4V to 14V 0 (Note 3) Bandwidth Common-Mode Voltage Range Common-Mode Rejection CS_ Input Current CS+/CS- Input-Referred Offset VCMR CMR (ICS- + ICS+) VIOCS CSOUT Load Current ICSOUT k_ kHz 14 8 VCSOUTCLP V dB 2 4 A 0 +2.0 mV VCS+ - VCS- = 48mV, gain = 20 1 5 VCS+ - VCS- = 24mV, gain = 20 2 5 VCS+ - VCS- = 24mV, gain = 40 1 5 -2.0 20 Rising, CSFLGEN = logic 1 0.912 0.96 1.008 Falling, CSFLGEN = logic 1 0.862 0.91 0.958 % A V Start-Up Time CSOUT Clamp Voltage pF 350 VCS+ - VCS- = 48mV, gain = 20 (Bit D6 of register 09h) CS Flag (BIT D1 of Register 0Dh) 50 100 VLVRPWR = VCS- = VCS+ = 5.4V to 13.2V Gain = 20, VCS+ = VCS- = VLVRPWR = 5.4V to 14V VLVRPWR = 5.4V to 14V CSOUT Voltage Accuracy mV 150 5.4 VLVRPWR = VCS- = 5.4V to 14V, VCS+ = VCS- + 24mV 60 1.215 1.242 _______________________________________________________________________________________ 60 s 1.270 V High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices (V_IN = 7.2V, EP = GND, VPWREN = 5V, _LX unconnected, CREF = 0.1F; when V_IN is specified, it implies all _IN pins; TA = -40C to +85C. Typical values are at TA = +25C, unless otherwise noted. Limits are 100% production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design and characterization.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS GPIO LOGIC INPUT/OUTPUT GPIOPWR UVLO Rising 2.8 Falling 2.5 0.7 x VGPIOPWR Rising Input Threshold V 0.25 x Falling Output-Voltage Low VGPIOPWR IGPIO_ = -20mA, open-drain output Open-Drain Leakage Current VGPIO_ = 5.5V V 0.5 TA = +25C 0.01 TA = +85C 0.1 0.1 V A Minimum Input Data Setup Time tDS 100 ns Minimum Input Data Hold Time tDH 1 s 5 s Input mode 1 M_ Open-drain output mode 10 k_ 244 Hz Minimum Delay to Output Data Valid Pullup Resistor from GPIO_ to GPIOPWR VGPIOPWR = 5V GPIO_ PWM Clock Frequency OPEN-DRAIN COMPARATOR CMPI Input Current ICMPI VCMPI = 600mV CMPI Threshold VCMPI Rising CMPI Hysteresis VCMPIHYS t CMPO 25mV overdrive Output-Voltage Low V CMPO I CMPO = -20mA ICMPOLKG 1.25 A 1.2875 40 CMPO Delay Open-Drain Leakage Current 0.01 1.2125 V CMPO = 14V mV 5 s 0.4 TA = +25C 0.01 TA = +85C 0.1 V 1.0 V A _______________________________________________________________________________________ 9 MAX8904 ELECTRICAL CHARACTERISTICS (continued) MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices ELECTRICAL CHARACTERISTICS (continued) (V_IN = 7.2V, EP = GND, VPWREN = 5V, _LX unconnected, CREF = 0.1F; when V_IN is specified, it implies all _IN pins; TA = -40C to +85C. Typical values are at TA = +25C, unless otherwise noted. Limits are 100% production tested at TA = +25C. Limits over the operating temperature range are guaranteed by design and characterization.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 0.8 V +1 A 0.4 V 400 kHz I2C SERIAL INPUT/OUTPUT AND LOGIC Logic Input Low Voltage VIL Logic Input High Voltage VIH 2.0 Input Leakage Current ILKG -1 Output-Voltage Low VOL V ISINK = 3mA Input/Output Capacitance CI/O Serial-Clock Frequency fSCL 10 pF Clock Low Period tLOW 1.3 s Clock High Period tHIGH 0.6 s BUS Free Time tBUF 1.3 s START Setup Time tSU:STA 0.6 s START Hold Time tHD:STA 0.6 s STOP Setup Time tSU:STO 0.6 s Data-In Setup Time tSU:DAT 100 Data-In Hold Time tHD:DAT 0 ns 900 ns Receive SCL/SDA Minimum Rise Time tR (Note 5) 20 + 0.1 x CBUS ns Receive SCL/SDA Maximum Rise Time tR (Note 5) 300 ns Receive SCL/SDA Minimum Fall Time tF (Note 5) 20 + 0.1 x CBUS ns Receive SCL/SDA Maximum Fall Time tF (Note 5) 300 ns Transmit SDA Fall Time tF CBUS = 400pF Pulse Width of Spike Suppressed tSP (Note 6) 20 + 0.1 x CBUS 300 ns 50 ns 3.6 ms 3V3 Disable to 1V8 Disable Delay 15 ms 1V8 Disable to 1V2 Disable Delay 15 ms SEQUENCER POWER-UP SEQUENCING 1V8 VOK to 3V3 Start Delay POWER-DOWN SEQUENCING Note 3: Not tested. Design guidance only. Note 4: The idle-mode current threshold is the transition point between fixed-frequency PWM operation and idle-mode operation. The specification is given in terms of output load current for inductor values specified in Figure 1. Note 5: CBUS = total capacitance of one bus line in pF. Rise and fall times are measured between 0.1 x VBUS and 0.9 x VBUS. Note 6: Input filters on SDA and SCL suppress noise spikes < 50ns. 10 ______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices 1.248 5.075 5.070 5.065 1.247 -15 10 35 TEMPERATURE (NC) 60 85 MAX8904 toc03 VPWREN = 0V 25 20 15 10 5 0 5.060 -40 -15 10 35 TEMPERATURE (NC) 60 1V2, 1V8, AND 3V3 ARE ON 1.3 2 4 6 8 10 INPUT VOLTAGE (V) 1.0 0.8 0.5 0.3 1.0 1V2, 1V8, AND 3V3 ARE ON NO-LOAD SUPPLY CURRENT (mA) 1.5 85 12 14 INPUT CURRENT vs. TEMPERATURE (CH2 + CH3 + CH7, SWITCHING, NO LOAD) INPUT CURRENT vs. INPUT VOLTAGE (CH2 + CH3 + CH7 SWITCHING, NO LOAD) MAX8904 toc04 -40 30 MAX8904 toc05 LVROUT VOLTAGE (V) 1.249 MAX8904 toc02 MAX8904 toc01 5.080 1.250 NO-LOAD SUPPLY CURRENT (mA) REFERENCE VOLTAGE (V) 1.251 SHUTDOWN SUPPLY CURRENT vs. INPUT VOLTAGE LVROUT VOLTAGE vs. TEMPERATURE SHUTDOWN SUPPLY CURRENT (uA) REFERENCE VOLTAGE vs. TEMPERATURE 0.9 0.8 0.7 0.6 0.5 0.4 0 3 6 9 12 INPUT VOLTAGE (V) -40 15 STARTUP SEQUENCING WAVEFORMS -15 10 35 TEMPERATURE (NC) VPWREN V1V2 0V V1V8 0V 3V 1.2V 1.8V MAX8904 toc07 5V/div VPWREN 0V V5V0 0V 2V/div 3.3V 5V/div 0V 2V/div 0V 2V/div 1.8V 5V 2V/div 0V 1.2V V1V2 V1V8 2ms/div 3V 2V/div 2V/div V3V3 85 SHUTDOWN SEQUENCING WAVEFORMS MAX8904 toc06 0V 60 3.3V 2V/div V3V3 0V 10ms/div ______________________________________________________________________________________ 11 MAX8904 Typical Operating Characteristics (VIN = 7.2V, VPWREN = 3V, SHDN unconnected, VADJ = 4V, CREF = 0.1F, circuit of Figure 1, TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (VIN = 7.2V, VPWREN = 3V, SHDN unconnected, VADJ = 4V, CREF = 0.1F, circuit of Figure 1, TA = +25C, unless otherwise noted.) SHUTDOWN SEQUENCING WAVEFORMS EFFICIENCY vs. INPUT VOLTAGE (1V8) MAX8904 toc08 IOUT = 600mA 5V/div 0V 3V V3V3 100 MAX8904 toc09 VPWREN 95 2.3V 5.0V 0V 4V 0V 2V/div VADJ 0V EFFICIENCY (%) 2V/div V5V0 2V/div 90 85 80 75 70 4ms/div 3 6 9 12 INPUT VOLTAGE (V) 15 1V8 LOAD TRANSIENT RESPONSE (10mA TO 485mA) EFFICIENCY vs. OUTPUT CURRENT (1V8) MAX8904 toc11 MAX8904 toc10 100 90 80 485mA IOUT 70 EFFICIENCY (%) 10mA 500mA/div 60 50 40 V1V8 AC RIPPLE 30 50mV/div 20 10 0 1 10 100 OUTPUT CURRENT (mA) 1000 200s/div OUTPUT VOLTAGE LOAD REGULATION (1V8) 1V8 LOAD TRANSIENT RESPONSE (500mA TO 1000mA) MAX8904 toc12 MAX8904 toc13 1.90 1.86 V1V8 AC RIPPLE 20mV/div 1000mA IOUT 500mA 500mA/div OUTPUT VOLTAGE (V) MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices VIN = 12V 1.82 VIN = 7.2V 1.78 VIN = 3.4V 1.74 1.70 20s/div 12 1 10 100 OUTPUT CURRENT (mA) ______________________________________________________________________________________ 1000 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices EFFICIENCY vs. OUTPUT CURRENT (3V3) EFFICIENCY vs. INPUT VOLTAGE (3V3) IOUT = 800mA 90 80 90 70 EFFICIENCY (%) EFFICIENCY (%) MAX8904 toc15 100 MAX8904 toc14 100 80 60 50 40 30 70 20 10 0 60 3 6 9 12 INPUT VOLTAGE (V) 1 15 10 100 1000 OUTPUT CURRENT (mA) 3V3 LOAD TRANSIENT RESPONSE (625mA TO 1250mA) 3V3 LOAD TRANSIENT RESPONSE (10mA TO 625mA) MAX8904 toc16 MAX8904 toc17 625mA IOUT 1250mA 625mA IOUT 10mA 1A/div 500mA/div V3V3 AC RIPPLE 50mV/div I3V3 AC RIPPLE 20mV/div 200s/div 200s/div 100 MAX8904 toc19 MAX8904 toc18 100 95 90 80 3.40 70 90 EFFICIENCY (%) VIN = 12V EFFICIENCY (%) OUTPUT VOLTAGE (V) EFFICIENCY vs. OUTPUT CURRENT (5V0) EFFICIENCY vs. INPUT VOLTAGE (5V0) 3.44 85 80 75 1 10 100 1000 OUTPUT CURRENT (mA) 10,000 50 40 20 IOUT = 650mA 10 0 70 3.28 60 30 3.32 VIN = 7.2V MAX8904 toc20 OUTPUT VOLTAGE LOAD REGULATION (3V3) 3.36 10,000 5 7 9 11 INPUT VOLTAGE (V) 13 15 1 10 100 OUTPUT CURRENT (mA) 1000 ______________________________________________________________________________________ 13 MAX8904 Typical Operating Characteristics (continued) (VIN = 7.2V, VPWREN = 3V, SHDN unconnected, VADJ = 4V, CREF = 0.1F, circuit of Figure 1, TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (VIN = 7.2V, VPWREN = 3V, SHDN unconnected, VADJ = 4V, CREF = 0.1F, circuit of Figure 1, TA = +25C, unless otherwise noted.) 5V0 LOAD TRANSIENT RESPONSE (10mA TO 400mA) 5V0 LOAD TRANSIENT RESPONSE (400mA TO 800mA) MAX8904X toc22 MAX8904X toc21 800mA 400mA 400mA IOUT 500mA/div 10mA 500mA/div V5V0 AC RIPPLE V5V0 AC RIPPLE 50mV/div 20mV/div 200s/div 200Fs/div EFFICIENCY vs. OUTPUT CURRENT (ADJ) EFFICIENCY vs. INPUT VOLTAGE (ADJ) 100 MAX8904 toc24 MAX8904 toc23 100 95 90 80 VIN = 12V 5.02 4.97 VIN = 5.5V 70 90 EFFICIENCY (%) EFFICIENCY (%) VIN = 7.2V 5.07 85 80 10 100 OUTPUT CURRENT (mA) 1000 50 40 20 10 PULSE-SKIPPING MODE ENABLED 0 70 1 60 30 IOUT = 1000mA VADJ = 4V 75 4.92 MAX8904 toc25 OUTPUT VOLTAGE LOAD REGULATION (5V0) 5.12 5 7 9 11 INPUT VOLTAGE (V) 13 ADJ LOAD TRANSIENT RESPONSE (200mA TO 2000mA TO 200mA) 1 15 10 100 1000 OUTPUT CURRENT (mA) ADJ VOLTAGE vs. LOAD CURRENT (ADJ) MAX8904X toc26 4.10 MAX8904 toc27 IOUT OUTPUT VOLTAGE (V) 2000mA 1A/div IOUT 200 mA VADJ AC RIPPLE 50mV/div OUTPUT VOLTAGE (V) MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices VIN = 7.2V 4.05 4.00 VIN = 12V 3.95 VIN = 5.4V 3.90 200s/div 14 1 10 100 OUTPUT CURRENT (mA) ______________________________________________________________________________________ 1000 10,000 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices ADJ SHUTDOWN RESPONSE ADJ STARTUP RESPONSE MAX8904X toc29 MAX8904X toc28 4V 4V 2V/div VADJ VADJ 0V 0V 2V/div 1A 1A 1A/div 0A 0A 1A/div 1ms/div 1ms/div 90 0.9 MAX8904 toc31 20.40 MAX8904 toc30 100 BST SWITCHING FREQUENCY vs. TEMPERATURE LED CURRENT vs. TEMPERATURE ILED = 20mA SWITCHING FREQUENCY (MHz) EFFICIENCY vs. LED CURRENT (BST) 6 LEDS 4 LEDS LED CURRENT (mA) 8 LEDS 70 60 20.30 20.25 50 40 6 12 18 LED CURRENT (mA) 24 30 0.8 0.7 0.6 0.5 20.20 -40 -15 10 35 TEMPERATURE (NC) 60 -40 85 BST STARTUP RESPONSE (CURRENT MODE) -15 10 35 TEMPERATURE (NC) MAX8904X toc33 100 95 10V/div 0V 30mA ILED 0mA 85 EFFICIENCY vs. INPUT VOLTAGE (BST VOLTAGE MODE) 8 WLEDS VBST 60 MAX8904 toc34 0 20mA/div EFFICIENCY (%) EFFICIENCY (%) 20.35 80 MAX8904 toc32 IOUT IOUT 90 85 80 VOUT = 13.2V IOUT = 50mA 75 70 2s/div 5 7 9 11 INPUT VOLTAGE (V) 13 15 ______________________________________________________________________________________ 15 MAX8904 Typical Operating Characteristics (continued) (VIN = 7.2V, VPWREN = 3V, SHDN unconnected, VADJ = 4V, CREF = 0.1F, circuit of Figure 1, TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (VIN = 7.2V, VPWREN = 3V, SHDN unconnected, VADJ = 4V, CREF = 0.1F, circuit of Figure 1, TA = +25C, unless otherwise noted.) EFFICIENCY vs. LOAD CURRENT (BST VOLTAGE MODE) BST LOAD TRANSIENT RESPONSE (10mA TO 60mA, VOLTAGE MODE) MAX8904X toc36 MAX8904 toc35 100 90 80 EFFICIENCY (%) 70 100mV/div VBST AC RIPPLE 60 50 60mA 40 IOUT 30 25mA/div 10mA 20 10 VOUT = 13.2V 0 100 BST VOLTAGE vs. LOAD CURRENT 13.200 VIN = 7.2V 13.199 VIN = 5.4V 13.198 IOUT = 300mA 95 EFFICIENCY (%) 13.201 100 90 80 70 90 EFFICIENCY (%) VIN = 12V 13.202 EFFICIENCY vs. OUTPUT CURRENT (1V2) EFFICIENCY vs. INPUT VOLTAGE (1V2) 100 MAX8904 toc37 13.203 200s/div MAX8904 toc39 10 LOAD CURRENT (mA) MAX8904 toc38 1 OUTPUT VOLTAGE (V) MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices 85 80 60 50 40 30 20 75 10 13.197 0 70 1 10 LOAD CURRENT (mA) 100 3 6 9 12 INPUT VOLTAGE (V) 1 15 1V2 LOAD TRANSIENT RESPONSE (300mA TO 600mA) 1V2 LOAD TRANSIENT RESPONSE (1mA TO 300mA) MAX8904 toc40 MAX8904X toc41 300mA IOUT IOUT 1mA 600mA 500mA/div 300mA 200mA/div V1V2 AC RIPPLE 50mV/div 200Fs/div 16 10 100 OUTPUT CURRENT (mA) V1V2 AC RIPPLE 20mV/div 200Fs/div ______________________________________________________________________________________ 1000 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices CLS STARTUP RESPONSE (NO LOAD) OUTPUT VOLTAGE LOAD REGULATION (1V2) MAX8904X toc43 MAX8904 toc42 1.28 OUTPUT VOLTAGE (V) 1.26 12V VCLSIN 10V/div 0V 500mA/div VIN = 12V ICLSIN 1.24 1.22 500mA/div ICLSOUT VIN = 7.2V 1.20 VCLSOUT 10V/div 0V VIN = 3.4V CCLSOUT = 2000F 1.18 1 10 100 OUTPUT CURRENT (mA) 1000 20ms/div CLS STARTUP AND SHUTDOWN RESPONSE (425mA LOAD) CLS SHORT-CIRCUIT PROTECTION MAX8904X toc44 MAX8904X toc45 12V VCLSIN 12V 10V/div VCLSOUT ICLSIN ICLSIN ICLSOUT 3.3V 200ms/div 100ms/div OPEN-DRAIN COMPARATOR CSOUT VOLTAGE vs. TEMPERATURE (GAIN = 20, VCS+ - VCS- = 48mV) 0.945 0V 1V/div 7.2V 7.2V 0V 5V/div CSOUT VOLTAGE (V) 0V MAX8904 toc47 0.950 1.3V 5V/div 0V VFLT MAX8904X toc46 VCMPO 500mA/div 0mA 10V/div 0V CCLSOUT = 2000F VCMPI 500mA/div 0mA 500mA/div ICLSOUT VCLSOUT 10V/div 0V 0V 500mA/div 0.940 0.935 0.930 0.925 10s/div -40 -15 10 35 TEMPERATURE (NC) 60 85 ______________________________________________________________________________________ 17 MAX8904 Typical Operating Characteristics (continued) (VIN = 7.2V, VPWREN = 3V, SHDN unconnected, VADJ = 4V, CREF = 0.1F, circuit of Figure 1, TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (VIN = 7.2V, VPWREN = 3V, SHDN unconnected, VADJ = 4V, CREF = 0.1F, circuit of Figure 1, TA = +25C, unless otherwise noted.) CSA OUTPUT VOLTAGE vs. INPUT VOLTAGE GAIN = 20 VCS+ - VCS- = 48mV 0.940 0.935 0.930 0.96 0.94 -15 10 35 TEMPERATURE (NC) 60 85 0.96 0.94 0.90 0.90 -40 0.98 0.92 0.92 0.925 GAIN = 40 VCS+ - VCS- = 24mV OUTPUT VOLTAGE (V) 0.98 OUTPUT VOLTAGE (V) 0.945 1.00 MAX8904 toc49 1.00 MAX8904 toc48 0.950 CSA OUTPUT VOLTAGE vs. INPUT VOLTAGE MAX8904 toc50 CSOUT VOLTAGE vs. TEMPERATURE (GAIN = 40, VCS+ - VCS- = 24mV) OUTPUT VOLTAGE (V) MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices 5 7 9 11 INPUT VOLTAGE (V) 13 OVERVOLTAGE PROTECTION 15 5 7 9 11 INPUT VOLTAGE (V) REVERSE-POLARITY PROTECTION MAX8904 toc52 MAX8904 toc51 5V/div VOVPWR VOVGATE V_IN 12V 0V 14.5V 14V 5V/div 12V 5V/div VFLT VRPGATE VIN 3.3V 5V/div 10V/div VEXT -28V 0V 5V/div 0V 5V/div IEXT 100mA/div 10ms/div 10ms/div GPIO PWM OPERATION SHDN FUNCTIONALITY MAX8904 toc54 MAX8904 toc53 3V 2V/div VSHDN VGPIO4 V5VO 0V 5V/div 5V/div REGISTER 06h = 40h VGPIO5 4V VADJ REGISTER 05h = 20h 0V 5V 13.2V 0V 5V/div 5V/div REGISTER 05h = 80h 5V/div VGPIO6 5V/div VBST 0V 4ms/div 18 REGISTER 06h = 100h 5V/div VGPIO7 2ms/div ______________________________________________________________________________________ 13 15 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices PIN NAME 1 CSOUT Output Voltage of the Current-Sense Amplifier. CSOUT is referenced to analog ground, GND. Its fullscale voltage is 1.2V for 60mV differential input voltage at CS+ and CS-. RPGATE External p-MOSFET Gate Control Node for Reverse Polarity Protection. Internal reverse polarity sense circuitry controls the gate so that power is applied to the following n-MOSFET stage if and only if proper (positive) polarity of power is applied. If reverse polarity input power is applied, the p-MOSFET is kept off to protect the n-MOSFET stage and the IC. OVPWR Supply Voltage and Overvoltage Detection Node for the Overvoltage Protection Circuitry. Connect OVPWR to system external supply in the absence of reverse polarity protection p-MOSFET. When reverse polarity protection p-MOSFET is used, connect OVPWR to the source of the reverse polarity protection p-MOSFET. 4 OVGATE External n-MOSFET Gate Control Node for Input Overvoltage Protection. The external n-MOSFET is turned on as long as VOVPWR is less than 13.3V. The external n-MOSFET is immediately turned off by pulling OVGATE low, when VOVPWR exceeds 13.3V, and the IC asserts the FLT output. The external n-MOSFET is turned back on when VOVPWR falls below OVP threshold. Note that the I2C interface is always alive, is independent of the overvoltage protection circuit, and turns off only when VLVROUT falls below 3.4V. 5 ADJBST ADJ Step-Down Converter Boost Capacitor Connection. Connect a 0.1F ceramic capacitor between ADJBST and ADJLX_. 6, 7 ADJLX1, ADJLX2 ADJ Step-Down Converter Switching Node. Connect an inductor between ADJLX_ and the output of the ADJ converter. Connect a 0.1F ceramic capacitor between ADJLX_ and ADJBST. Connect ADJLX1 to ADJLX2. 8 ADJIN ADJ Step-Down Converter Supply Input. Bypass ADJIN to power ground with a 4.7F ceramic capacitor. Connect ADJIN to the input power supply node, VIN. 9 ADJFB ADJ Step-Down Converter Feedback Input. Connect two 22F or a 47F output ceramic capacitor from the output inductor to power ground, and route the sense trace to ADJFB. 10 REF 1.25V Reference Output. Bypass REF to GND with a 0.1F ceramic capacitor. REF is internally pulled to GND in shutdown. 11 GND Ground. Connect GND to the ground plane. Connect the ground plane with a short wide connection to the exposed pad (EP). 12 LVRIN5V Power Supply for the Internal Analog Circuitry. It is derived from an internal low-voltage regulator output, LVROUT. Connect a 10_ resistor between LVRIN5V and LVROUT. Bypass LVRIN5V to GND with a 1.0F or greater ceramic capacitor. 13 LVROUT Internal Low-Voltage Regulator Output Bootstrapped to 5V0 Step-Down Converter Output. LVROUT is the power supply for the internal drive circuitry. LVROUT provides a 5V output when PWREN is pulled high. Bypass LVROUT to power ground with a 1.0F or greater ceramic capacitor. 14 LVRPWR Internal 5V Low-Voltage Linear Regulator Input Supply. Decouple LVRPWR to power ground with a 0.22F or greater ceramic capacitor. Connect LVRPWR to the input power-supply node, VIN. 15 5V0FB 5V0 Step-Down Converter Feedback Input. Connect a 22F output ceramic capacitor from the output inductor to power ground, and route the sense trace to 5V0FB. 16 5V0IN 5V0 Step-Down Converter Input Supply. Bypass 5V0IN to power ground with a 10F ceramic capacitor. Connect 5V0IN to the input power-supply node, VIN. 2 3 FUNCTION ______________________________________________________________________________________ 19 MAX8904 Pin Description High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices MAX8904 Pin Description (continued) 20 PIN NAME FUNCTION 17 5V0LX 18 5V0BST 19 GPIOPWR Power Supply for GPIO Inputs and Outputs. GPIOPWR can be connected to a supply voltage from 3.0V up to 5.5V. Correct a 1F ceramic capacitor between GPIOPWR and GND. 20-27 GPIO0- GPIO7 I2C-Controlled GPIO Port. GPIO_ can be configured as: * Schmitt-trigger inputs with internal 1M pullup resistor to GPIOPWR * Open-drain outputs with internal 10k pullup resistor off-state and capable of sinking 20mA current from GPIOPWR * Open-drain outputs with high-impedance off-state and capable of sinking 20mA current from GPIOPWR * High-impedance outputs The default configuration during power-up is Schmitt-trigger inputs until reconfigured through the I2C interface. The GPIO block has a dedicated power input supply, GPIOPWR. The MAX8904 samples its GPIO0 at GPIOPWR power-up and selects one of two internal hardwired slave addresses for I2C addressing. 28 CMPO Active-Low, Open-Drain Output of an Uncommitted Comparator. CMPO can be pulled up to 14V. 29 CMPI Comparator Input. Internal reference voltage is 1.25V. 30 3V3FB 3V3 Step-Down Converter Feedback Input. Connect two 22F or a 47F output ceramic capacitor from the inductor to power ground, and route the sense trace to 3V3FB. The 3V3FB provides power to the I2C registers. Connect the SDA and SCL pullup resistors to 3V3FB. 31 3V3IN 3V3 Step-Down Converter Input Supply. Connect a 4.7F ceramic capacitor between 3V3IN and power ground. Connect 3V3IN to the input power supply node, VIN. 32 3V3LX 3V3 Step-Down Converter Switching Node. Connect an inductor between 3V3LX and the output of the 3V3 converter. Connect a 0.1F ceramic capacitor between 3V3LX and 3V3BST. 33 3V3BST 34 SCL I2C Serial-Clock Input 35 SDA I2C Serial-Data Input/Output. Data is read on the rising edge of SCL. 36 1V2BST 37 1V2LX 1V2 Step-Down Converter Switching Node. Connect an inductor between 1V2LX and the output of the 1V2 converter. Connect a 0.1F ceramic capacitor between 1V2LX and 1V2BST. 38 1V2IN 1V2 Step-Down Converter Input Supply. Bypass 1V2IN to power ground with a 4.7F ceramic capacitor. Connect 1V2IN to the input power supply node, VIN. 39 1V2FB 1V2 Step-Down Converter Feedback Input. Connect two 22F or a 47F output ceramic capacitor from the inductor to power ground, and route sense trace to 1V2FB. 1V2FB is sampled at power-up to determine if the 1V2 step-down converter is used or not. See the Power-Up/Down Sequencing for 1V2, 1V8, 3V3, and 5V0 Supplies section. Pull 1V2FB to LVRIN5V to configure the IC for operation without the 1V2 step-down converter. 40 FLT 5V0 Step-Down Converter Switching Node. Connect an inductor between 5V0LX and the output of the 5V0 converter. Connect a 0.1F capacitor between 5V0LX and 5V0BST. 5V0 Step-Down Converter Boost Capacitor Connection. Connect a 0.1F ceramic capacitor between 5V0BST and 5V0LX. 3V3 Step-Down Converter Boost Capacitor Connection. Connect a 0.1F ceramic capacitor between 3V3BST and 3V3LX. 1V2 Step-Down Converter Boost Capacitor Connection. Connect a 0.1F ceramic capacitor between 1V2BST and 1V2LX. Active-Low, Open-Drain Fault Output. Low FLT indicates a fault condition. See the Fault Handling section for details. ______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices PIN NAME 41 SHDN Shutdown Input. When SHDN is pulled low, the power converters that are selected in the SHUTDOWN register, if currently active, are immediately shut down. The IC recognizes a valid signal on SHDN only if 1V2, 1V8, and 3V3 supplies are in regulation. 42 PWREN Enable Input. When PWREN is driven high, the LVROUT regulator is turned on, and the 1V2, 1V8, 3V3, and 5V0, are turned on with correct sequencing depending on the status of 1V2FB at LVR power-up. When PWREN is pulled low, the MAX8904 turns off all converters and internal blocks and goes into low-power standby mode. 43 TEST 44 1V8FB 1V8 Step-Down Converter Feedback Input. Connect a 22F output ceramic capacitor from the output inductor to power ground, and route the sense trace to 1V8FB. 45 1V8IN 1V8 Step-Down Converter Input Supply. Bypass 1V8IN to power ground with a 4.7F ceramic capacitor. Connect the 1V8IN to the input power supply node, VIN. 46 1V8LX 1V8 Step-Down Converter Switching Node. Connect an inductor between 1V8LX and the output of 1V8 converter. Connect a 0.1F ceramic capacitor between 1V8LX and 1V8BST. 47 1V8BST 1V8 Step-Down Converter Boost Capacitor Connection. Connect a 0.1F ceramic capacitor between 1V8BST and 1V8LX. 48 BSTLX BST Open-Drain Switch Node. Connect an inductor between BSTSW and BSTLX. BSTLX is high impedance in standby mode. 49 BSTSW BST True Shutdown Switch Terminal. Connect an inductor between BSTSW and BSTLX. Bypass BSTSW to power ground with a 2.2F ceramic capacitor. 50 BSTIN BST Step-Up Converter Supply Input. Bypass BSTIN to power ground with a 1F ceramic capacitor. Connect BSTIN to the input power supply node, VIN. 51 BSTFB BST Step-Up Converter Feedback Input. Connect BSTFB to the output ceramic capacitor of the step-up converter. Use a 1F capacitor in current regulator mode and use a 10F capacitor for voltage regulator mode. 52 PCS LED Current Sink. When the BST step-up converter is in current-mode operation, connect the cathode of WLED string to PCS and the anode of the WLED string to the output capacitor. In voltage mode, PCS must be connected to GND. 53 CLSOUT Current-Limited Switch Output. Turn on the load switch through the I2C interface to connect the switch input, CLSIN, to the load. 54 CLSIN 55 CS- 56 CS+ -- EP FUNCTION Test Pin. Leave as no connection. Do not connect power or ground. Current-Limited Switch Input. Connect CLSIN to the input power supply node, VIN. Current-Sense Amplifier Inverting Input. Connect CS- to the load side of current-sense resistor. Current-Sense Amplifier Noninverting Input. Connect CS+ to the supply-side of current-sense resistor. Exposed Pad. Power grounds and ground plane must be star-connected to the EP. All large currents from converters flow through the exposed pad that also acts as a heat sink. A large number of vias are needed to connect EP to board power ground plane. ______________________________________________________________________________________ 21 MAX8904 Pin Description (continued) MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices R1 10 VIN 5V VIN CLSOUT VIN 5V0 C3 1F C2 1F LVRPWR LVROUT LVRIN5V PWREN CH1 425mA CURRENT LIMITER 5V0LX C23 22F C22 0.1F INTERNAL CHIP SUPPLY LINEAR REGULATOR CH4 5V0 STEP-DOWN CONVERTER (800mA MAX) 5V BOOTSTRAP 5V0BST C4 1F BSTSW CH6 BST STEP-UP CONVERTER 667kHz, 12.8V TO 32V, 1.12W OUTPUT POWER, I2C PROGRAMMABLE 5V0FB VIN L5 4.3H 3V3LX CH3 3V3 STEP-DOWN CONVERTER (1250mA MAX) MAX8904 1V8LX C9 0.1F LOAD VIN 1.25V 3V3 OR 5V0 CLK 8-BIT I2C PROGRAMMABLE I/O ADJIN C15 4.7F ADJLX1 ADJLX2 CH5 ADJ STEP-DOWN CONVERTER (3V TO 5.1V I2C PROG,) (1500mA MAX RMS, 2A PULSE) THERMAL FLAG AND SHUTDOWN LEVEL SHIFT ADJFB INTERNAL OSC 1MHz 10% SCL OVP SENSE, REVERSE POLARITY SENSE AND CPUMP DRIVE LVRIN5V SDA LOGIC CENTER SERIAL I/O, OUTPUT VOLTAGE PROGRAMMING, ON/OFF CONTROL, SOFT-START FAULT MANAGEMENT FLT SHDN REG2 ALWAYS ON C12 0.1F REF C10 1F VIN VCS+ -VCS= 0 TO 60mV R2 15m C11 680F C25 0.022F Q1 RPGATE REF EP GND CS+ CSOUT (0 TO 1.2V) Q2 OVGATE CLK LVROUT GPIOPWR GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7 CS- 20 ADJBST OVPWR VEXT 3.4V TO 13.2V (+30V/-28V FAULT PROTECTED) NOTE: 1V2, 1V8, AND ADJ OPERATE IN PHASE. 3V3 AND 5V0 OPERATE INPHASE WITH RESPECT TO EACH OTHER, BUT ARE DELAYED BY 300ns WITH RESPECT TO 1V2, 1V8, AND ADJ. Figure 1. Typical Application Circuit and Function Diagram 22 1V2 C8 2x 22F CMPO 1V8FB C14 2x 22F C13 0.1F 1V2LX CMPI CH2 1V8 STEP-DOWN CONVERTER (975mA MAX) 1V8BST L3 4.3H VIN C7 L2 4.7F 4.7H 1V2BST 1V2FB C17 22F C16 0.1F ADJ 4 TO 8 WLEDS 1V8IN C18 4.7F VIN R3 10 1V2IN CH7 1V2 STEP-DOWN CONVERTER (600mA MAX) 3V3FB 1V8 C6 1F D2 BSTFB 3V3BST L4 4.7H BST BSTLX PCS C20 2x 22F C19 0.1F VIN C5 2.2F L1 10H D1 3V3IN C21 4.7F 3V3 VIN BSTIN 5V0IN C24 4.7F L6 10H CLSIN C1 0.22F ______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices The MAX8904 power-management ICs provide a complete power-supply solution for 2-cell Li+ handheld/Li-Poly applications such as point-of-sale terminals, digital SLR cameras, digital video cameras, and ultra-mobile PCs. The MAX8904 include five step-down converters (1V20.6A, 1V8-0.975A, 3V3-1.25A, 5V0-0.8A, and ADJ1.5A) with internal MOSFETs and +1%/-3% accurate output voltages for processor core, memory, I/O, and other system power rail requirements. The ADJ converter provides an adjustable output voltage that is 6bit programmable through the I2C interface from 3.0V to 5.1V, in 33.3mV steps. LCD backlighting is supported by a WLED boost converter that can provide 35mA for up to 8 WLEDs while operating in the current regulator mode. This boost converter is also configurable as a 6 bit programmable voltage source that can provide up to 63mA of output current. In this voltage mode, the output voltage is 6-bit programmable through the I2C interface from 12.5V to 18.7V, in 100mV steps. System input current monitoring for power management is facilitated by an on-board Current Sense Amplifier (CSA) with differential inputs and a 1.2V full scale ground referenced analog output. The CSA has an I2C programmable gain of 20V/V and 40V/V for fullscale outputs of 4A and 2A, respectively, when used with a 15m current-sense resistor. A 400kHz, I2C interface supports output voltage setting of ADJ power rail and boost regulator (voltage source mode), WLED current setting for the boost regulator (WLED current regulator mode), enable/disable of ADJ, 5V0, boost regulator, CSA and GPIO control. The I2C interface also enables the host processor to read onboard fault status registers when interrupted by the MAX8904 FLT pin under system fault conditions. An emergency shutdown input, SHDN allows converters preselected through I2C to turn off immediately, thus saving valuable firmware execution time under power fail conditions. The MAX8904 features an 8-bit GPIO port controller with PWM capability. The GPIO port pins power up as Schmitttrigger CMOS inputs. Programmable configurations are: * Schmitt-trigger input with internal 1M pullup to GPIOPWR * Open-drain output, with internal 10k pullup resistor off-state, capable of sinking up to 20mA current from GPIOPWR * Open-drain output with high-impedance state, capable of sinking up to 20mA current from GPIOPWR * High-impedance output GPIO0 can be used to set the I2C slave address of the MAX8904 to either CEh or 8Eh (see Table 1). A current-limited switch (CLS) is provided, with a minimum output current of 425mA, which allows system designers to control input power to external peripheral devices. The MAX8904 supports input overvoltage protection (OVP) at 13.5V (typ) by controlling an external n-MOSFET and reverse polarity protection (down to -28V) of downstream circuits by controlling an external p-MOSFET. An uncommitted, active-low, high voltage open-drain comparator (CMP) with a 1.25V internal reference and 20mA sink current capability that can function as a buzzer driver or can be used for power fail sensing is also provided. The MAX8904's PWREN logic input turns on 1V2, 1V8, 3V3, and 5V0 default power rails. An internal 5V lowvoltage linear regulator powered from the input power source provides power for the internal drive and control blocks. When the input is below 5V, the regulator output follows the input down to 3.4V. When the input voltage drops below 3.4V (UVLO), all circuitry except the overvoltage protection block are turned off. When the input voltage drops below 2.85V (OVPWR UVLO), the overvoltage protection block is turned off. I2C Interface The MAX8904 internal I2C serial interface provides flexible control setup, including ON/OFF control of all power converters (except 1V2, 1V8, and 3V3), CLS, CSA and CMP, the ADJ output voltage, the BST output voltage or output current, and the 8-bit GPIO port functionality. The MAX8904 internal control and fault status registers are also accessed through the standard bidirectional, 2-wire I2C serial interface. The I2C serial interface consists of a serial-data line (SDA) and a serial-clock line (SCL) to achieve bidirectional communication between the master and the slave. The MAX8904 is a slave-only device, relying upon a master to generate a clock signal. The master (typically a microprocessor) initiates data transfer on the bus and generates SCL to permit data transfer. The MAX8904 supports SCL clock rates up to 400kHz. I2C is an open-drain bus. SDA and SCL require pullup resistors (500 or greater). Optional resistors (24) in series with SDA and SCL protect the device inputs from high-voltage spikes on the bus lines. Series resistors also minimize crosstalk and undershoot on bus signals. ______________________________________________________________________________________ 23 MAX8904 Detailed Description MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices I2C Slave Address A bus master initiates communication with MAX8904 as a slave device by issuing a START condition followed by the MAX8904 address. As shown in Table 1, the MAX8904 responds to either one of two internally hardwired slave addresses depending on the GPIO0 status when GPIOPWR powers up for the first time and exceeds its UVLO (rising) threshold. This address is latched internally and can only be changed if the LVRPWR voltage is cycled, and the GPIOPWR voltage exceeds UVLO again. Pullup Voltage The MAX8904 I2C interface SDA and SCL line should use the 3V3 supply as its pullup voltage. START and STOP Conditions Both SDA and SCL remain high when the serial interface is inactive. The master signals the beginning of a transmission with a START (S) condition by transitioning SDA from high to low while SCL is high. When the master has finished communicating with the MAX8904, it Table 1. MAX8904 Slave Addresses GPIO0 STATUS AT V GPIOPWR > VGPIOPWR_UVLO (RISING) SLAVE ADDRESS READ SLAVE ADDRESS WRITE Logic 0 (GPIO0 pulled down by an internal 100k resistor between GPIO0 and GND) 8Fh 8Eh Logic 1 (GPIO0 pulled up by an internal 1M resistor between GPIO0 and GPIOPWR) CFh CEh issues a STOP (P) condition by transitioning SDA from low to high while SCL is high. The bus is then free for another transmission (Figure 2). Both START and STOP conditions are generated by the bus master. To send a series of commands to the MAX8904, the master issues REPEATED START (Sr) commands instead of a STOP command to maintain the bus control. In general, a REPEATED START command is functionally equivalent to a regular START command. When a STOP condition or incorrect address is detected, the MAX8904 internally disconnect SCL from the bus until the next START condition to minimize digital noise and feedthrough. Data Transfer Each data bit, from the most significant bit to the least significant bit, is transferred one by one during each SCL clock cycle. The data on SDA must remain stable during the high period of the SCL clock. Changes in SDA while SCL is high are control signals (see the START and STOP Conditions section). Each transmit sequence is framed by a START condition and a STOP condition. Each data packet is nine bits long: eight bits of data followed by an acknowledge bit. Acknowledge Both the I2C bus master and the MAX8904 (slave) generate acknowledge bits when receiving data. The acknowledge bit is the last bit of each nine bit data packet. To generate an acknowledge (A) signal, the receiving device pulls SDA low before the rising edge SDA tSU, STA tSU, DAT tHD, DAT tLOW tBUF tHD, STA tSU, STO SCL tHIGH tHD, STA tR tF START CONDITION REPEATED START CONDITION STOP CONDITION Figure 2. 2-Wire Serial Interface Timing Detail 24 ______________________________________________________________________________________ START CONDITION High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices Communication Protocols The following I2C communication protocols are supported by the MAX8904: * Writing to a single register * Writing multiple bytes using register-data pairs * Reading from a single register * Reading from sequential registers Writing to a Single Register Figure 4 shows the protocol for the master device to write one byte of data to the MAX8904. The write byte protocol is as follows: 1) The master sends a START (S) command. 2) The master sends the 7-bit slave address followed by a write bit (low). 3) The addressed slave asserts an acknowledge (A) by pulling SDA low. 4) The master sends an 8-bit register pointer. 5) 6) 7) 8) 9) The slave acknowledges the register pointer. The master sends a data byte. The slave updates with the new data The slave acknowledges the data byte. The master sends a STOP (P) condition. NOT ACKNOWLEDGE (NA) S ACKNOWLEDGE (A) SDA tSU:DAT 1 SCL 2 8 tHD:DAT 9 Figure 3. Acknowledge LEGEND MASTER TO SLAVE SLAVE TO MASTER 1 7 1 1 8 1 8 1 1 S SLAVE ADDRESS 0 A REGISTER POINTER A DATA A P NUMBER OF BITS R/nW Figure 4. Write-Byte Format ______________________________________________________________________________________ 25 MAX8904 of the acknowledge-related clock pulse (ninth pulse) and keeps it low during the high period of the clock pulse (Figure 3). To generate a not-acknowledge (NA) signal, the receiving device allows SDA to be pulled high before the rising edge of the acknowledge-related clock pulse and leaves it high during the high period of the clock pulse. Monitoring the acknowledge bits allows for detection of unsuccessful data transfers. An unsuccessful data transfer occurs if a receiving device is busy or if a system fault has occurred. In the event of an unsuccessful data transfer, the bus master should reattempt communication at a later time. MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices Writing Multiple Bytes Using Register-Data Pairs Figure 5 shows the protocol for the master device to write multiple bytes to the MAX8904 using register-data pairs. It allows the master to address the slave only once and then send data to multiple registers in a random order. Registers may be written continuously until the master issues a STOP (P) condition. The write multiple bytes using register-data pairs protocol is as follows: 9) Steps 5 to 8 are repeated as many times as the master requires. Registers may be accessed in random order. 10) The master sends a STOP (P) condition. Reading from a Single Register Figure 6 shows the protocol for the master device to read one byte of data from the MAX8904. The read byte protocol is as follows: 1) The master sends a START (S) command. 2) The master sends the 7-bit slave address followed by a write bit (low). 3) The addressed slave asserts an acknowledge (A) by pulling SDA low. 1) The master sends a START (S) command. 2) The master sends the 7-bit slave address followed by a write bit (low). 3) The addressed slave asserts an acknowledge by pulling SDA low. 4) The master sends an 8-bit register pointer. 5) The slave acknowledges the register pointer. 6) The master sends a data byte. 4) The master sends an 8-bit register pointer. 5) The slave acknowledges the register pointer. 6) The master sends a REPEATED START (Sr) command. 7) The slave updates with the new data. 8) The slave acknowledges the data byte. LEGEND MASTER TO SLAVE 1 SLAVE TO MASTER 7 S SLAVE ADDRESS 1 1 8 1 8 1 0 A REGISTER POINTER X A DATA X A 8 1 8 1 A DATA n A 1 8 1 1 A P NUMBER OF BITS R/nW REGISTER POINTER n 8 REGISTER POINTER Z A DATA Z NUMBER OF BITS NUMBER OF BITS Figure 5. Multiple Bytes Register-Data Pair Format LEGEND MASTER TO SLAVE 1 7 S SLAVE ADDRESS SLAVE TO MASTER 1 1 8 1 1 7 1 1 8 1 1 0 A REGISTER POINTER X A Sr SLAVE ADDRESS 1 A DATA X nA P R/nW R/nW Figure 6. Read-Byte Format 26 ______________________________________________________________________________________ NUMBER OF BITS High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices 3) The addressed slave asserts an acknowledge (A) by pulling SDA low. 4) The master sends an 8-bit register pointer. 5) The slave acknowledges the register pointer. 6) The master sends a REPEATED START (Sr) command. 7) The master sends the 7-bit slave address followed by a read bit (high). 8) The addressed slave asserts an acknowledge (A) by pulling SDA low. 9) The addressed slave places 8-bits of data on the bus from the location specified by the register pointer. 10) The master asserts a not-acknowledge on the data line to complete operations. 11) The master issues a STOP (P) condition. 8) The addressed slave asserts an acknowledge by pulling SDA low. 9) The addressed slave places 8-bits of data on the bus from the location specified by the register pointer. Reading from Sequential Registers Figure 7 shows the protocol for reading from sequential registers. This protocol is similar to the read byte protocol except that the master issues an acknowledge to signal the slave that it wants more data. When the master has all the data, it issues a not-acknowledge (NA) and a STOP condition (P) to end the transmission. The continuous read from sequential registers protocol is as follows: 10) The master issues an acknowledge (A) signaling the slave that more data is needed. 11) Steps 9 and 10 are repeated as many times as the master requires. Following the last byte of data, the master issues a not-acknowledge (NA) to signal that it wishes to stop receiving data. 12) The master issues a STOP (P) condition. 1) The master sends a START (S) command. 2) The master sends the 7-bit slave address followed by a write bit (low). LEGEND MASTER TO SLAVE SLAVE TO MASTER 1 7 1 1 8 S SLAVE ADDRESS 0 A REGISTER POINTER X 1 1 A Sr 7 1 1 8 1 SLAVE ADDRESS 1 A DATA X A R/nW NUMBER OF BITS R/nW 8 1 8 1 8 1 DATA X + 1 A DATA X + 2 A DATA X + 3 A 8 1 8 1 8 1 DATA n - 2 A DATA n - 1 A DATA n NUMBER OF BITS 1 NUMBER OF BITS nA P Figure 7. Read from Sequential Registers Format ______________________________________________________________________________________ 27 MAX8904 7) The master sends the 7-bit slave address followed by a read bit (high). MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices I2C Accessible Registers The I2C accessible registers are used to store all the control information from the SDA line and configure the MAX8904 for different operating conditions. Recycling power at LVRPWR causes the MAX8904 to initialize the registers to their POR values. The register assignments of the MAX8904 are in Table 2. Table 2. Register Assignments POR REGISTER R/W VALUE ADDRESS 28 REGISTER NAME D7 D6 D5 D4 D3 D2 D1 D0 00h R/W 00h GPIO-A CONFIG PWM enable/ disable PWM bank select GPIO1 configuration bits PWM enable/ disable PWM bank select GPIO0 configuration bits 01h R/W 00h GPIO-B CONFIG PWM enable/ disable PWM bank select GPIO3 configuration bits PWM enable/ disable PWM bank select GPIO2 configuration bits 02h R/W 00h GPIO-C CONFIG PWM enable/ disable PWM bank select GPIO5 configuration bits PWM enable/ disable PWM bank select GPIO4 configuration bits 03h R/W 00h GPIO-D CONFIG PWM enable/ disable PWM bank select GPIO7 configuration bits PWM enable/ disable PWM bank select GPIO6 configuration bits 04h R/W 00h GPIO-DATA I/O-8 I/O-7 I/O-6 I/O-5 I/O-4 I/O-2 I/O-1 I/O-0 05h R/W 00h PWM-BANK0 MSB -- -- -- -- -- -- LSB 06h R/W 00h PWM-BANK1 MSB -- -- -- -- -- -- LSB 07h R/W 00h ENABLE CSAEN X CMPEN BSTEN ADJEN 5V0EN INIT CLSEN 08h R/W 00h SHUTDOWN (SHDN) CSA X CMP BST ADJ 5V0 X CLS 09h R/W 00h MODE CSAG CSFLGEN X BSTIV ADJM X X OVOFF 0Ah R/W 00h ADJSP Lockout X MSB -- -- -- -- LSB 0Bh R/W 00h BSTCSP X X MSB -- -- -- -- LSB 0Ch R/W 00h BSTVSP Lockout X MSB -- -- -- -- LSB 0Dh R 00h VOKFLT OLFLT TMP120 X OCIN OVIN 0Eh R 00h OVERLOAD BSTOL ADJOL 5V0OL 3V3OL 1V8OL 1V2OL X CLSOL 0Fh R FFh VOK BSTOK ADJOK 5V0OK 3V3OK 1V8OK 1V2OK X CLSOK 10h R -- DEVICE ID Chip ID MSB -- -- -- Chip ID LSB Chip Rev MSB -- Chip Rev LSB 11h W 00h CLRFLTS FAULTSTATUS BSTFLT1 BSTFLT0 Fault status and fault registers are cleared and FLT goes to high when CLRFLTS register is set to 01h. Fault detection rearms when CLRFLTS is set back to 00h. ______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices GPIO Data Register The GPIO Data register (04h) is a read/write (R/W) register that allows the host processor to read those GPIO bits that are programmed as inputs and write to those GPIO bits that are programmed as outputs through the I2C interface. For a read operation, all eight bits are read regardless of whether they are configured as inputs or outputs. It allows the host processor to read status of all eight bits. For a write operation, only those bits that are configured as outputs are written to, and the input bits are neglected. On power-up, all GPIO bits are configured to inputs by default. Each data bit represents a physical GPIO port and its functionality is given in Table 3. PWM Bank Register The PWM Bank registers PWM-BANK0 (05h) and PWMBANK1 (06h) are used to set up two different pulsewidth modulation values and switch between them by changing the value of the PWM bank select bit (D6/D2) in the GPIO Configuration registers (00h to 04h). Running at a clocking rate of 244Hz, these two registers allow the LEDs to be driven at 256 discrete levels of intensity control, from 0.0s on/4.1ms off (0%) to 4.084ms on/16s off (99.6%). When multiple LEDs are controlled by the GPIO ports, the use of two PWM registers allows some LEDs to be dimmed while other LEDs are simultaneously brightened. Individual LEDs can also be switched between two intensities by toggling its PWM-BANK assignment. See Table 5. Table 3. GPIO Configuration Register (00h to 03h) PWM ENABLE PWM BANK D7/D3 D6/D2 X X 0 = Disabled 1 = Enabled 0 = BANK0 1 = BANK1 0 = Disabled 1 = Enabled 0 = BANK0 1 = BANK1 X X 0 0 GPIO CONFIGURATION GPIO CONFIGRUATION DESCRIPTION D5/D1 D4/D0 0 0 GPIO-Data (04h): 0 = low, 1 = high 0 Open-drain n-device with 10k pullup resistor to GPIO, and tolerant of sinking current from 5V power supply 0 Open-drain n-device with high-impedance state, and tolerant of sinking current from 5V power supply GPIO-Data (04h): 0 = pull, 1 = push 1 Input with 1M pullup resistor to GPIO 1 GPIO-Data (04h): 0 = sink, 1 = pullup 1 DATA BITS 1 High-impedance (Hi-Z) output GPIO-Data (04h): 0 = Hi-Z, 1 = Hi-Z 0 0 Reset value = 0h Table 4. GPIO Data Register (04h) D7 D6 D5 D4 D3 D2 D1 D0 DATA BITS IO8 IO7 IO6 IO5 IO4 IO3 IO2 IO1 Reset value = 00h Table 5. GPIO PWM Bank Register (05h, 06h) D7 D6 D5 D4 D3 D2 D1 D0 DATA BITS MSB -- -- -- -- -- -- LSB PWM-BANK0 MSB -- -- -- -- -- -- LSB PWM-BANK1 0 0 0 0 0 0 0 0 Reset value = 00h ______________________________________________________________________________________ 29 MAX8904 GPIO Configuration Register The 00h to 03h registers allow the host processor to setup GPIO0-GPIO7 configuration through the I 2 C interface. Each nibble represents a physical GPIO port. These eight nibbles address all the operating requirements of the 8-bit GPIO port, including PWM dimming. LED blinking requirement is addressed by turning the LEDs on and off at the required rate through the I2C interface. The least significant two bits of each nibble define whether the particular GPIO bit is either an input or an output. If it is an output bit, the output device structure (open-drain/pullup, open-drain/high impedance, or high impedance/high impedance) is also defined by these two bits. On power-up, the eight GPIO bits are configured as inputs. See Table 3 for details. MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices Enable Register With the exception of the 1V2, 1V8, and 3V3 power converters, the Enable register (Table 6) allows the host processor to enable/disable the individual channel when needed. If a bit is programmed to 1, the corresponding power converter is enabled; otherwise, with a value of 0, the corresponding power converter remains disabled, even if valid data has been programmed in the associated set point register (0Ah, 0Bh, or 0Ch) for the ADJ or BST power converter. Conversely, if the ADJEN bit for ADJ or the BSTEN bit for BST is set to 1, with a set point register (0Ah, 0Bh, or 0Ch) value of 00h, the ADJ or BST power converter remains disabled. When the MAX8904 turns off a particular power converter under a fault condition, it sets the corresponding Enable register bit to 0. Firmware Initialization for CLS Operation The MAX8904 requires a mandatory firmware procedure to be executed by the host processor after turning ON the CLS block to initialize the CLS block correctly. The following firmware steps should be executed after turning ON the CLS block before responding to an interrupt on the FLT pin of the MAX8904: * Execute a 300ms (min) delay. * Shutdown Register The Shutdown register works in conjunction with SHDN to program which converters are turned off in the event of a power failure. SHDN is connected to the midpoint of a resistor-divider from LVRIN5V to GND, and is nominally at 3.3V (see Table 7). Upon receiving a power-fail signal, the host processor asserts the active-low SHDN, and only those power converters whose corresponding bits are programmed to 0 in the Shutdown register are turned off, and their associated Enable bits in the Enable register, if currently programmed to 1, are set to 0. The power converters whose bits in the Shutdown register are programmed to 1 remain enabled. If a power failure occurs, where the external power source voltage falls below the 3.4V, the MAX8904 enters the UVLO state. It powers up with default settings when it subsequently comes out of UVLO. Note that the host processor can still hold SHDN low at this point and it does not cause any action on the MAX8904. The MAX8904 performs the shutdown operation only when it detects a high-to-low transition on SHDN. Note that the 1V2, 1V8, and 3V3 power controllers are always ON and can not be turned off through the Shutdown register. Note that the 1V2, 1V8, 3V3, and 5V0 converters are turned on when PWREN is pulled high, but the 5V0 converter can be turned on/off by the Enable register bits once it is above its VOK thresholds. The 1V2, 1V8, and 3V3 converters can be turned off only by pulling PWREN low. Firmware Initialization at Power-Up The MAX8904 requires a mandatory firmware procedure to be executed by the host processor at power-up to initialize the part correctly. The following register writes should be executed before responding to an interrupt on the FLT pin of the MAX8904. * 04(h) Register 07(h) (Sets the INIT bit to 0) * 01(h) Register 11(h) * 00(h) Register 11(h) After the 300ms delay, execute the following register writes: 01(h) Register 11(h) 00(h) Register 11(h) Note that the firmware should keep the INIT bit set to 0 under all operating conditions. Table 6. Enable Register (07h) D7 D6 D5 D4 D3 D2 D1 D0 RESET CSAEN X CMPEN BSTEN ADJEN 5V0EN INIT CLSEN 00h Table 7. Shutdown Register (08h) 30 D7 D6 D5 D4 D3 D2 D1 D0 RESET CSA X CMP BST ADJ 5V0 X CLS 00h ______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices to 0, the overvoltage protection circuit determines the state of the external overvoltage protection n-MOSFET. When it is programmed to 1, the overvoltage protection n-MOSFET is turned off. CSAG (Bit 7): The MAX8904 provides a programmable gain current-sense amplifier. The CSAG bit is used to determine the gain setting for CSA. If it is programmed to 0, the amplifier gain is set to 20V/V. If it is programmed to 1, the amplifier gain is set to 40V/V. CSFLGEN (Bit 6): The CSFLGEN bit is used to enable/disable the CSA input over-current fault detection feature. If the CSFLGEN bit is high, the MAX8904 sets the OCIN (D1) bit in the FAULT STATUS register, and asserts FLT when an input overcurrent is sensed at CSOUT. The input overcurrent fault detection is disabled if CSFLGEN is set to 0. BSTIV (Bit 4): The BST step-up converter supports voltage mode or current mode operation and the mode selection is realized by the BSTIV bit. If it is programmed to 0, the converter operates in the current mode with the BSTCSP register setting. If it is programmed to 1, the converter operates in the voltage mode with the BSTVSP register setting. ADJSP Register The MAX8904 uses the I2C interface to set the output voltage of ADJ power controller. A 6-bit value adjusts the ADJ output voltage from 3V to 5.067V, in 33.3mV increments (see Table 10). It is an invalid setting if the ADJSP register is set as 00h (2.967V). The first valid setting is 01h (3V). See Table 9 for the ADJSP register definition. Table 10 shows hex codes for various output voltage settings of the ADJ power controller. Bit 7 (LOCKOUT) of the ADJSP register allows the voltage setting to be programmed only one time after power-up. After power-up, the host processor sets the ADJSP value only once. When the host processor changes the 00h setting to a valid number, the MAX8904 sets the LOCKOUT bit to 1. Once it is set to 1, subsequent changes to the 6-bit ADJSP value are locked out. Only by recycling power, the LOCKOUT bit can be restored to 0. Note that the ADJSP register is an R/W register, and it allows the user to read the lockout bit and determine whether the MAX8904 had already been set to a valid output voltage. ADJM (Bit 3): The MAX8904 supports automatic switching from pulse-width modulation (PWM) to pulseskipping modulation (PSM) to improve power supply efficiency at light loads for all of the power converters except the ADJ step-down converter that must be set by the ADJM bit. Because the pulse-skipping mode has inherently larger voltage ripple, it may be necessary for the ADJ supply to remain in pulse-width modulation mode when powering noise sensitive loads such as a GPRS radio module. ADJM bit allows the host processor to force the ADJ controller to remain in PWM mode, if desired. When it is programmed to 0, the ADJ power converter automatically switches between PSM and PWM modes. When it is programmed to 1, the power controller is forced to remain in PWM mode. OVOFF (Bit 0): The OVOFF bit is used to turn off the external overvoltage protection n-MOSFET, for the purpose of battery pack conditioning. When it is programmed When the MAX8904 detects that the ADJEN bit is 1, and recognizes valid data in the ADJSP register, the ADJ controller is enabled and soft-starts to the target output voltage. When the Enable bit for the ADJ power converter is set to 1 with an ADJSP register value of 00h, the ADJ stays in the off condition. Conversely, with the ADJEN bit set to 0, the regulator remains disabled, even if valid data has been programmed in the ADJSP register. Neither of these two conditions generates a FLT assertion, since the power converter is considered to be in the off state. Fault detection is enabled only if the ADJEN bit is high, and valid data has been programmed in the ADJSP register. See Table 11. Table 8. Mode Register (09h) D7 D6 D5 D4 D3 D2 D1 D0 RESET CSAG CSFLGEN X BSTIV ADJM X X OVOFF 00h Table 9. ADJSP Register (0Ah) D7 D6 D5 D4 D3 D2 D1 D0 RESET LOCKOUT X MSB -- -- -- -- LSB 00h 0 0 0 0 0 0 0 0 00h ______________________________________________________________________________________ 31 MAX8904 Mode Register The Mode register is used to configure the operating mode of various functional blocks. See Table 8. MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices Table 10. ADJ Output Voltage Settings ADJ VOLTAGE HEX CODE ADJ VOLTAGE HEX CODE 3.000 1 4.066 21 3.033 2 4.099 22 3.066 3 4.133 23 3.099 4 4.166 24 3.133 5 4.199 25 3.166 6 4.233 26 3.199 7 4.266 27 3.233 8 4.299 28 3.266 9 4.333 29 3.299 A 4.366 2A 3.333 B 4.399 2B 3.366 C 4.433 2C 3.399 D 4.466 2D 3.433 E 4.499 2E 3.466 F 4.533 2F 3.499 10 4.566 30 3.533 11 4.599 31 3.566 12 4.633 32 3.599 13 4.666 33 3.633 14 4.699 34 3.666 15 4.733 35 3.699 16 4.766 36 3.733 17 4.799 37 3.766 18 4.833 38 3.799 19 4.866 39 3.833 1A 4.899 3A 3.866 1B 4.933 3B 3.899 1C 4.966 3C 3.933 1D 4.999 3D 3.966 1E 5.033 3E 3.999 1F 5.066 3F 4.033 20 -- -- Table 11. ADJEN/ADJSP Truth Table 32 ADJEN BIT ADJSP VALID SET POINT ADJ ENABLED 0 00h No FAULT DETECTION ENABLED No 0 > 00h No No 1 00h No No 1 > 00h Yes Yes ______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices D7 D6 D5 D4 D3 D2 D1 D0 Reserved Reserved MSB -- -- -- -- LSB 00h X X 0 0 0 0 0 0 00h BST Current Set Point Register The BST step-up converter has two modes of operation: current and voltage. The current-mode operation is used to drive a WLED string, while the voltage-mode operation provides a regulated DC voltage for TFT or OLED panels. In the current mode, the WLED string is connected from the BST output to PCS and the control loop regulates the LED current to the value set in the BSTCSP register through the I2C interface. The BSTCSP register (0Bh) is defined in Table 12. A 6-bit value allows the host processor to adjust the current from 1mA to 63mA, in 1mA minimum increments. The maximum recommended increment is 16mA per I2C command. It is an invalid setting if the BSTCSP register is set to 00h (0mA). The first valid number is 01h (1mA). The 3Fh setting corresponds to 63mA (see Table 13 for WLED current settings and corresponding hex codes). RESET VALUE Table 13. BSTCSP LED Current Settings LED CURRENT (mA) HEX CODE LED CURRENT (mA) HEX CODE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 -- 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F -- The host processor can change the dimming levels as many times as desired during normal operation. In current mode, the value programmed in the BSTVSP register (0Ch) is used as an overvoltage threshold. When the output voltage in current mode reaches the threshold, the converter is immediately latched off, and it requires either the host processor to issue either a CLRFLTS command and drive BSTEN high, or recycling input power to start up again. Recommended overvoltage threshold settings for the LED strings are provided in Table 14. The overvoltage threshold is programmable from 13.4V to 32V in 300mV increments. A 00h setting in the BSTVSP register corresponds to 13.1V and is an invalid setting. A 01h value corresponds to a valid 13.4V overvoltage setting. The host processor can only program this overvoltage setting in the BSTVSP register once, after which the lockout bit is set to 1 to prevent subsequent programming attempts. The one-time programmability of the BSTVSP register applies to overvoltage setting in both current mode and voltage mode. Table 14. Overvoltage Threshold Settings for BST Regulator Current-Mode Operation NO. OF SERIES WLEDs 4 5 6 7 8 BSTVSP SETTING (V) 18.3 22.5 26.7 30.9 35.1 CODE IN BSTVSP REGISTER (0Ch) 04h 12h 20h 2Eh 3Ch ______________________________________________________________________________________ 33 MAX8904 Table 12. BSTCSP Register (0Bh) MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices BST Voltage Set Point Register When the BST operates in voltage mode, a device such as a TFT or OLED display panel can be connected between the BST output and power ground. PCS is connected to GND in this application to disable the current sink function. In this mode, the BST acts as a voltage source with current limit functionality and regulate its output to the value set in the BSTVSP register (see Table 15). A 6-bit value adjusts the voltage from 12.5V to 18.7V in 100mV increments (see Table 16). It is an invalid setting if the BSTVSP register is set to 00h (12.4V). The first valid number is 01h (12.5V). Note that with an output of 12.5V, the converter may be operating in dropout for an input voltage of 12.6V. Table 15. BSTVSP Register (0Ch) D7 D6 D5 D4 D3 D2 D1 D0 Lockout Reserved MSB -- -- -- -- LSB RESET -- 0 X 0 0 0 0 0 0 00h Table 16. BSTVSP Voltage Settings and Hex Codes 34 OUPUT VOLTAGE (V) HEX CODE OUTPUT VOLTAGE (V) HEX CODE 12.5 01 15.7 21 12.6 02 15.8 22 12.7 03 15.9 23 12.8 04 16 24 12.9 05 16.1 25 13 06 16.2 26 13.1 07 16.3 27 13.2 08 16.4 28 13.3 09 16.5 29 13.4 0A 16.6 2A 13.5 0B 16.7 2B 13.6 0C 16.8 2C 13.7 0D 16.9 2D 13.8 0E 17 2E 13.9 0F 17.1 2F 14 10 17.2 30 14.1 11 17.3 31 14.2 12 17.4 32 14.3 13 17.5 33 14.4 14 17.6 34 14.5 15 17.7 35 14.6 16 17.8 36 14.7 17 17.9 37 14.8 18 18 38 14.9 19 18.1 39 3A 15 1A 18.2 15.1 1B 18.3 3B 15.2 1C 18.4 3C 15.3 1D 18.5 3D ______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices OUPUT VOLTAGE (V) HEX CODE OUTPUT VOLTAGE (V) HEX CODE 15.4 1E 18.6 3E 15.5 1F 18.7 3F 15.6 20 -- -- MAX8904 Table 16. BSTVSP Voltage Settings and Hex Codes (Voltage Mode) (continued) Table 17. BSTEN/BST_SP Truth Table BST_SP VALID SET POINT BSTEN BIT BST ENABLED FAULT DETECTION ENABLED 0 00h No No 0 > 00h No No 1 00h No No 1 > 00h Yes Yes Bit 7 (LOCKOUT) of the BSTVSP register allows the voltage setting to be programmed only one time after power-up. After power-up, the host processor sets the BSTVSP value only once. When the host processor changes the 00h setting to a valid number, the MAX8904 sets LOCKOUT bit to 1. Once it is set to 1, subsequent changes to the 6-bit BSTVSP value are locked out. Only by recycling power, the LOCKOUT bit can be restored to 0. Note that the BSTVSP register is an R/W register, and it allows the user to check the lockout bit. In voltage mode, when the MAX8904 detects that the BSTEN bit is 1 and recognizes valid data in the BSTVSP register, the BST regulator is enabled and soft-starts to the target output voltage. When the BSTEN is set to 1 with a BSTVSP register value of 00h, the BST regulator stays in the off condition. Conversely, with the BSTEN bit set to 0, the regulator remains disabled, even if the valid data has been programmed in the BSTVSP register. Neither of these two conditions generates a FLT assertion, since the regulator is considered to be in the off state. Fault detection is enabled only if the BSTEN bit is high, and valid data has been programmed in the BSTVSP register. See Table 17. Fault Handling The MAX8904 has two fault registers (VOK and OVERLOAD) and a fault status register (FAULTSTATUS). See Tables 18, 20, and 21 for details about these register bits. Table 18. Fault Status Register (0Dh) D7 D6 D5 D4 D3 D2 D1 D0 RESET BSTFLT1 BSTFLT0 VOKFLT OLFLT TMP120 X OCIN OVIN 00h Table 19. BST Fault Bit Description BSTFLT1 BSTFLT0 FAULT DESCRIPTION 0 0 No fault. 0 1 Overvoltage (current mode only). 1 0 Open or reverse output diode, or open BSTFB connection (detected at startup before BSTLX switching). 1 1 PCS short to GND fault, or BST output short to PCS fault (current mode only, detected at startup before BSTLX switching). Table 20. Overload Register (0Eh) D7 D6 D5 D4 D3 D2 D1 D0 RESET BSTOL VADJOL 5V0OL 3V3OL 1V8OL 1V2OL X CLSOL 00h Table 21. VOK Register (0Fh) D7 D6 D5 D4 D3 D2 D1 D0 RESET BSTOK VADJOK 5V0OK 3V3OK 1V8OK 1V2OK X CLSOK 11h ______________________________________________________________________________________ 35 MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices The MAX8904 handles faults as outlined in Tables 22 and 23. The FAULTSTATUS register indicates the type of system fault that has occurred. The BSTFLT0, BSTFLT1 bits are set based on the type of fault that has occurred in the BST step-up converter (see Table 19). The VOKFLT bit is set when a VOK fault has occurred on any one of the power converters. A VOK fault occurs either when a converter fails to softstart or due to overload/short-circuit conditions on the output under normal operation, causing the output voltage to fall below its VOK threshold. The _OK bits in the VOK register are set to 1 at power up. When a VOK fault occurs, the _OK bit corresponding to the faulty converter is set to 0, indicating a VOK fault in the particular converter. The OLFLT bit is set when the output current on a converter exceeds its overload threshold. The _OL bit in the OVERLOAD register corresponding to the faulty converter is set to 1 indicating an overload fault in the particular converter. The TMP120 bit is set when the internal die temperature exceeds +120C. With the current sense resistor across CS+, CS- pins of the MAX8904 connected in series with the input power source, the OCIN bit is set when the CSOUT voltage exceeds its CSFLAG threshold, indicating an input overcurrent condition. The OVIN bit is set when the input voltage sensed at the OVPWR pin exceeds the overvoltage threshold. Table 22. Fault Handling FAULT TYPE FAULT RESPONSE AND RECOVERY * Overload on 1V2, 1V8, 3V3 * VOK fault on 1V2, 1V8, 3V3 (detected after internal soft-start time plus a 2ms delay). * FLT goes to low, all regulators are turned off immediately after fault detection, and the corresponding bits in FAULTSTATUS, OVERLOAD, and VOK registers are set. * Fault detection is enabled for a regulator only if CLRFLTS=00h, and PWREN is high. * Toggling PWREN (highlowhigh) if PWREN is still high, or driving PWREN from low to high resets all fault status and fault registers, pulls FLT to high, and causes the MAX8904 to restart the 1V2, 1V8, 3V3, and 5V0 supplies. * Recycling power to the LVRPWR input of the internal linear regulator causes the MAX8904 to power up and remain in standby mode if PWREN is low. If PWREN is high, the MAX8904 attempts to start the 1V2, 1V8, 3V3, and 5V0 supplies. * VCLSIN-VCLSOUT > 1V, VOK fault on the current limited switch at the end of 250ms soft-start time * Overvoltage, open LED fault on LED step-up converter (current mode only) * LED cathode (PCS) short to ground detected before BSTLX switching (current mode only) * LED cathode (PCS) short to LED boost output, detected before BSTLX switching (current mode only) * Missing or reversed output diode, open BSTFB connection, detected before BSTLX switching. * FLT goes to low and the regulator turns off immediately after fault detection. The corresponding bits in FAULTSTATUS, OVERLOAD, and VOK registers are set. * Setting CLRFLTS to 01h followed by CLRFLTS to 00h at any time clears all fault registers bits, pulls FLT to high, and rearms the MAX8904 for subsequent fault detection. * Fault detection is enabled for a regulator only if CLRFLTS=00h, and _EN=1 (The ADJ and BST step-up regulators also require valid data to be programmed in the ADJSP and BSTCSP/BSTVSP registers). * The regulator restarts, fault registers are cleared, FLT goes to high, if the _EN bit is toggled from 0 to 1. * Toggling PWREN (highlowhigh) if PWREN is still high, or driving PWREN from low to high resets all fault status and fault registers, pulls FLT to high, and causes the MAX8904 to restart the 1V2, 1V8, 3V3, and 5V0 supplies. * Recycling power to the LVRPWR input of the internal linear regulator causes the MAX8904 to power up and remain in standby mode if PWREN is low. If PWREN is high, the MAX8904 attempts to start the 1V2, 1V8, 3V3, and 5V0 supplies. 36 ______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices FAULT TYPE FAULT RESPONSE AND RECOVERY * BSTFB or LED anode shorted to ground (an external 40V-rated Schottky diode must be connected from power ground to BSTFB, as close as possible to the BSTFB capacitor) * FLT goes to low and BSTLX switching stop immediately after fault detection. The corresponding bits in FAULTSTATUS, OVERLOAD registers are set. The BST regulator turns off 250ms after the fault. * Setting CLRFLTS to 01h followed by CLRFLTS to 00h at any time clears all fault registers bits, pulls FLT to high, and rearms the MAX8904 for subsequent fault detection. * Fault detection is enabled for a regulator only if CLRFLTS = 00h, and BSTEN = 1. Valid data must be programmed in the BSTCSP/BSTVSP registers). * The regulator restarts, fault registers are cleared, FLT goes to high, if the BSTEN bit is toggled from 0 to 1. * Toggling PWREN (highlowhigh) if PWREN is still high, or driving PWREN from low to high resets all fault status and fault registers, pulls FLT to high, and causes the MAX8904 to restart the 1V2, 1V8, 3V3, and 5V0 supplies. * Recycling power to the LVRPWR input of the internal linear regulator causes the MAX8904 to power up and remain in standby mode if PWREN is low. If PWREN is high, the MAX8904 attempts to start the 1V2, 1V8, 3V3, and 5V0 supplies. * Overload on 5V0, ADJ, BST. VCLSIN-VCLSOUT > 1V, VOK fault on the current limiter in normal operation. * Output voltage < VOK falling threshold on 5V0, ADJ, BST (voltage mode only), (detected after soft-start time plus 2ms delay for 5V0, ADJ, and 1.024ms for BST. * FLT goes to low immediately after fault detection, and fault status and fault registers are set. * For tFLT 250ms, the _EN bit is set to 0, and the regulator turns off. * Setting CLRFLTS to 01h followed by CLRFLTS to 00h at any time clears all fault status and fault register bits, pulls FLT to high, and rearms the MAX8904 for subsequent fault detection. * FLT goes to low, fault status and fault register information of a tFLT < 250ms momentary fault event is latched until the command of setting CLRFLTS to 01h is issued. * Momentary tFLT < 250ms faults do not cause the regulator to turn off. * Fault detection is enabled for a regulator only if CLRFLTS = 00h, and _EN = 1. The ADJ and LED boost regulators also require valid data to be programmed in the ADJSP and BSTCSP or BSTVSP registers. * Regulator restarts and fault register and fault status register are cleared, FLT goes to high, if the _EN bit is toggled (0 to 1). * Toggling PWREN (highlowhigh) if PWREN is still high, or driving PWREN from low to high resets all fault status and fault registers, pulls FLT to high, and causes the MAX8904 to restart the 1V2, 1V8, 3V3, and 5V0 supplies. * Recycling power to the LVRPWR input of the internal linear regulator causes the MAX8904 to power up and remain in standby mode if PWREN is low. If PWREN is high, the MAX8904 attempts to start the 1V2, 1V8, 3V3, and 5V0 supplies. * Input overvoltage at OVPWR * If an overvoltage event occurs in normal operation, the MAX8904 turns off the external n-MOSFET through OVGATE immediately. * FLT goes to low and OVIN goes to 1 in fault status register immediately after fault detection. * If the input voltage falls below the voltage of VOV - VHYS_OV, the OVP n-MOSFET turns back on. However, FLT stays low and OVIN stays high until the MAX8904 receives the command setting CLRFLTS to 01h. * Setting CLRFLTS to 01h followed by CLRFLTS to 00h at any time clears all fault status and fault register bits, pulls FLT to high, and rearms the MAX8904 for subsequent fault detection. * If overvoltage persists, the OV n-MOSFET remains off, and the MAX8904 regulator input supply decays to 2.85V, and the MAX8904 turns off at this point. * If an overvoltage condition occurs at startup, the external OVP n-MOSFET does not turn on and the MAX8904 does not startup. Therefore no fault information is stored. ______________________________________________________________________________________ 37 MAX8904 Table 22. Fault Handling (continued) MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices Table 22. Fault Handling (continued) FAULT TYPE FAULT RESPONSE AND RECOVERY * 120C Overtemperature Flag * The MAX8904 sets the TMP120 bit in fault status register and pulls FLT low if the internal temperature reaches +120C (typ). All converters latch off when the temperature reaches +150C (typ), and the MAX8904 goes into standby mode. In this mode, the internal linear regulator is turned off and the I2C interface is no longer powered. Note that PWREN may still be held high in this mode. * Toggling PWREN (highlowhigh) or recycling MAX8904 power at LVRPWR allows the MAX8904 to come out of thermal shutdown. * Input Overcurrent * If CSFLGEN is high, then the OCIN bit in the fault status register is set to 1 in the fault status register, and FLT goes high. If CSFLGEN is low, no action is taken. * Setting CLRFLTS to 01h followed by CLRFLTS to 00h at any time clears all fault status and fault register bits, pulls FLT to high, and rearms the MAX8904 for subsequent fault detection. Table 23. Summary of MAX8904 Fault Status Register and Fault Register Actions FAULT TYPE ACTIONS Overload or short circuit on 1V2, 1V8, 3V3, 5V0, ADJ, and BST OLFLT is set to 1 in the FAULTSTATUS register, and corresponding _OL is set to 1 in the OVERLOAD register. VOK fault on 1V2, 1V8, 3V3, 5V0, ADJ, BST (voltage mode only), and current limiter VOKFLT is set to 1 in the FAULTSTATUS register, and corresponding _OK is set to 0 in the VOK register. FAULTSTATUS register: BSTFLT1 and BSTFLT0 are set to 00 if none of the listed faults has occurred. Overvoltage on BST, open or reversed output diode, open BSTFB connection, PCS shorted to ground, PCS shorted to BST output BSTFLT1 and BSTFLT0 are set to 01 for overvoltage on BST step-up converter (current mode only). BSTFLT1 and BSTFLT0 are set to 10 for open or reversed output diode, or open BSTFB connection (detected at startup before BSTLX switching). BSTFLT1 and BSTFLT0 are set to 11 for PCS shorted to ground or PCS shorted to BST output (current mode only, detected at startup before BSTLX switching). Input overvoltage fault OVIN is set to 1 in the FAULTSTATUS register. Input overcurrent fault OCIN is set to 1 in the FAULTSTATUS register for CSFLGEN = 1. +120C overtemperature flag TMP120 is set to 1 in the FAULTSTATUS register. Table 24. Device Identification Register (10h) D7 D6 D5 D4 D3 D2 D1 D0 -- Chip ID MSB -- -- -- Chip ID LSB Chip Rev MSB -- Chip Rev LSB Read only Device Identification Register Device identification register (10h) identifies the chip ID and revision, and is shown in Table 24. It is a read-only register. CLRFLTS Register The MAX8904 clears all fault registers when the CLRFLTS register (11h) is set to 01h, to allow the processor to reset the fault and restart the system. When a fault 38 occurs, the host processor is interrupted and enters its interrupt service routine (ISR). It masks the interrupt, services the fault by reading the MAX8904 registers, and may clear the fault(s) to recheck for fault(s) or immediately act upon the faults, and unmasks the interrupt. If the fault is still present, the FLT signal goes low and the host processor enters its ISR again. CLRFLTS must be set to 00h to rearm fault detection. ______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices The MAX8904 has an overvoltage protection block as shown in Figure 8. This block has its own UVLO thresholds, linear regulator, and reference. It essentially operates as a stand-alone overvoltage protection block. Applying an external voltage greater than 4V (typ) to OVPWR causes the overvoltage protection block to commence operation. At this time, the external n-MOSFET has not yet been turned on. After a 30ms delay, if the OVPWR voltage is less than 13.65V (typ), the overvoltage charge pump gate drive is powered up and OVGATE turns on the external n-MOSFET. Otherwise, if the OVPWR voltage is greater than 13.65V, OVGATE holds the n-MOSFET off. After the OVP n-MOSFET (Q1) powers up, the system voltage VINT comes up and powers the internal LVR linear regulator and all power inputs (_IN). When VIN exceeds the UVLO (rising), the MAX8904 waits for a logic-high signal on PWREN to start up the 1V2, 1V8, 3V3 and 5V0 supplies, provided VIN is greater than 5.6V (typ). Reverse polarity protection down to -28V is provided by use of an external p-MOSFET (Q2) to protect downstream circuitry. When the input voltage goes negative, RPGATE goes high to turn off the external p-MOSFET. When the VINT input voltage rises in the positive direction to a maximum of +30V, RPGATE pulls low and turns on the p-MOSFET. When an overvoltage event of up to +30V occurs, an internal clamp protects the gate of the p-MOSFET from excessive voltage such that the VGATE-SOURCE voltage of the external p-MOSFET (Q2) does not exceed 16V (typ). Current Limited Switch The current limited switch (CLS) allows the MAX8904 to control the amount of current that an external device draws from the supply voltage. The CLS is connected between the input supply voltage and the target peripheral device. It provides a peripheral current of at least 425mA, and is protected under short-circuit conditions. A short-circuit condition that lasts greater than 250ms latches the CLS off. The CLS can be enabled and disabled through the Enable register and can be selected for immediate power-fail shutdown in the Shutdown register. An internal thermal loop protects the CLS from an overload or short-circuit fault that causes excessive power dissipation across the switch. It reduces the current delivered by the CLS if the die temperature rises above a preset temperature threshold (+120C) and thus limits the power dissipation in the CLS. The thermal loop is enabled only when VCLSIN - VCLSOUT > 1V. VIN 15m BULK CAPACITOR Q2 _IN PINS CSCS+ MAX8904 5V0FB LVRPWR Q1 UVLO DC INPUT LVR LVROUT OVPWR OVERVOLTAGE AND REVERSE POLARITY SENSE OVGATE REG2 RPGATE Figure 8. Overvoltage and Reverse Polarity Protection ______________________________________________________________________________________ 39 MAX8904 Overvoltage and Reverse Polarity Protection MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices With bit CLSEN in Enable register set to 1, the 250ms timer is activated. During normal operation, if VCLSIN VCLSOUT > 1V, FLT is set, CLSOK bit is set to 0, the VOKFLT bit is set to 1, and the 250ms timer is started. If VCLSIN - VCLSOUT < 1V before the timer expires, the timer is reset and the IC resumes normal operation. The fault information is preserved and the status of FLT, CLSOK, and VOKFLT remain unchanged until the I2C receives a CLRFLTS command. If VCLSIN - VCLSOUT > 1V after 250ms, the CLS is turned off, FLT is asserted, the CLSOK bit is set to 0, the VOKFLT bit is set to 1, and the CLSEN is set to 0. The MAX8904 needs a CLRFLTS command to clear the fault information in the FAULTSTATUS and VOK registers and pull FLT high. Current-Sense Amplifier The current-sense amplifier measures the differential voltage across a current-sense resistor and generates an analog voltage proportional to the current-sense resistor differential voltage. This voltage is clamped internally to a maximum of 1.25V. The CSA has two programmable-gain settings, 20V/V and 40V/V. When used with a 15m current-sense resistor, it allows full-scale (1.2V) output for 4A and 2A currents, respectively. The CSA sets the CSAOL bit in the Overload register if the maximum current is exceeded. The CSA can be enabled and disabled through the Enable register and can be selected for immediate power-fail shutdown in the Shutdown register. Open-Drain Comparator The open-drain comparator (CMP) is an uncommitted, 14V open-drain output comparator with 20mA of sinking capability. The CMP can be used for various functions such as independent print-head temperature monitoring, voltage comparison, driving a Piezo Buzzer, or a 20mA load sinking. The CMP can be enabled and disabled through the Enable register and can be selected for immediate power-fail shutdown in the Shutdown register. FLT Interrupt The FLT interrupt is an active-low output that indicates any fault condition. The fault condition can be either internal (overtemperature) or external (overloaded output). For certain types of faults such as an overload fault, when FLT is driven low, an internal 250ms timer is started. When the timer expires the MAX8904 disables the affected power converter. During the 250ms, from the time of the interrupt until the time the converter is disabled, the host processor can respond to the interrupt 40 and take an action such as shutting down the power converter or some other appropriate action, such as, reducing the load current. For other emergency faults such as an overvoltage fault, there is no 250ms timer related operation, FLT is asserted and the converter is immediately turned off. ADJ Step-Down Converter The ADJ power converter is an adjustable voltage stepdown converter that can be adjusted over a 6-bit range from 3.0V to 5.067V, in 33.3mV increments. The ADJ power converter is intended to be used for powering various radio modules, such as Wi-Fi, GPRS, and CDMA. The ADJ supply is designed to support a 2A peak and 1.414A RMS output current load. An L-C filter may be connected to the output capacitor to attenuate the switching frequency ripple component to within radio module specification. Power-Up/Down Sequencing for 1V2, 1V8, 3V3, and 5V0 Supplies The PWREN signal initiates power-up of the default voltage rails on the MAX8904 if LVRPWR (the input of internal linear regulator) exceeds 5.6V (typ). The default power-up rails are 1V2, 1V8, 3V3, and 5V0. If the 1V2 rail is not used, pulling 1V2FB to LVRIN5 configures the MAX8904 to operate without its 1V2 rail, with the corresponding power sequencing option. Power-down sequencing operates in the reverse sequence of power-up after PWREN goes low. Figures 9 and 10 show the two power-up/down sequencing cases. Table 25 shows the sequencing truth table. The ADJ and BST supplies can be turned on by the host processor any time after the 3V3 supply reaches its regulation, but all rails and MAX8904 blocks are shut down when PWREN pulls low. Note that there is a fixed time delay (D5, 3.6ms, typ) between the 1V8 supply reaching its VOK threshold and the 3V3 supply start time. Table 25. Sequencing Truth Table STATE OF 1V2FB DURING D2 SEQUENCING MODE 0 1V2, 1V8, and 3V3 sequenced, followed by 5V0 1 1V8 and 3V3 sequenced, followed by 5V0 ______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices MAX8904 BSTFB ADJFB 5V0FB 3V3FB 1V8FB 1V2FB D6 LVRIN5V D2 D3 D4 D5 D8 D7 D_UP D8 D8 D_DOWN D_UP PWREN Figure 9. Power-Up/Down Sequencing with 1V2 Rail Used (See Table 26 for Timing Details) BSTFB ADJFB 5V0FB 3V3FB 1V8FB D6 1V2FB LVRIN5V D4 D5 D7 D8 D8 PWREN Figure 10. Power-Up/Down Sequencing Without 1V2 Rail Used (See Table 26 for Timing Details) ______________________________________________________________________________________ 41 MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices Table 26. Delay Time DELAY TIME (ms) D2 (response time) <1 D3 (1V/ms ramp rate) 1.2 D4 (1V/ms ramp rate) 1.8 D5 (fixed delay) 3.6 D6 (1V/ms ramp rate) 3.4 D7 (1V/ms ramp rate) 5 D8 (estimated voltage decay time) 15 D_UP (maximum power-up sequence) D_DOWN (estimated voltage decay time) Applications Information Inductors for Step-Down and BST Converters The MAX8904 power converters are optimized to work with specific values of inductors. Either 4.7H or 4.3H inductors should be used for the 1V2, 1V8, 3V3, and ADJ step-down converters. A 10H inductor should be used for the 5V0 step-down converter. Ensure that the inductor saturation current rating exceeds the peak inductor current, and the rated maximum DC inductor current exceeds the maximum output current. For most applications, use an inductor with a DC current rating 1.25 times the maximum required output current. For maximum efficiency, the inductor DC resistance should be as low as possible. A 10H inductor is recommended for the BST step-up converter. See Table 27 for recommended inductor specifications. Input and Output Capacitors The input capacitor in a DC-DC converter reduces current peaks drawn from the input power source and reduces switching noise in the controller. The impedance of the input capacitor at the switching frequency should be less than the input source's output impedance so that high-frequency switching currents do not pass through the input source. The DC-DC converter output capacitor keeps output ripple small and ensures control-loop stability. The output capacitor must also have low impedance at the switching frequency. 42 11.6 for all supplies, 10ms for 1V2, 1V8, and 3V3 45 Ceramic capacitors with X5R or X7R dielectrics are highly recommended for both input and output capacitors due to their small size, low ESR, and small temperature coefficients. It should be noted that the effective capacitance that can be obtained in ceramic capacitors should be derated based on their operating DC bias (maximum converter input voltage in the case of input capacitors and maximum converter output voltage in the case of output capacitors). See Table 27 for recommended capacitor specifications based on the considerations outlined above. CLS Output Capacitor To prevent the MAX8904 from sensing a startup fault condition, the maximum capacitance that should be connected to the CLSOUT pin is given by the following equation: CCLSOUT(MAX) < (425 - ILOAD) x 225/VCLSIN(MAX) where ILOAD is the load current on CLSOUT in mA, VCLSIN(MAX) is the maximum input voltage at CLSIN in volts, and CCLSOUT is in F. Bootstrap Capacitors Connect a 0.1F low-ESR ceramic capacitor between the _LX and _BST for all the step-down converters. The bootstrap capacitor provides the gate-drive voltage for the internal high-side MOSFET. X7R or X5R grade dielectrics are recommended due to their stable values over temperature. ______________________________________________________________________________________ High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices COMPONENT PART NUMBER PART DESCRIPTION L1 TOKO, DE3518 Series, 1127AS-100M Inductor, SMT 10H, 20%, 145m DCR, 1.2A L2, L4 TOKO, DE3518 Series, 1127AS-4R7M Inductors, SMT 4.7H, 20%, 60m DCR, 1.75A L3, L5 TOKO, DE4518 Series, 1124BS-4R3M Inductors, SMT 4.3H, 20%, 70m DCR, 2.65A L6 TOKO, DE4518 Series, 1124BS-100M Inductor, SMT 10H, 20%, 120m DCR, 1.75A C1 Murata, GRM188R71C224KA01D Ceramic capacitor, 0.22F, 10%, 16V, X7R, 0603 C2, C3, C10 Murata, GRM188R70J105KA01D Ceramic capacitors, 1.0F, 10%, 6.3V, X7R, 0603 C4 Taiyo Yuden, EMK212BJ105KG-T Ceramic capacitor, 1.0F, 10%, 16V, X7R, 0805 C5 Taiyo Yuden, EMK212BJ225KG-T Ceramic capacitor, 2.2F 10%, 16V, X7R, 0805 C6 (current mode) Taiyo Yuden, UMK316B7105KL-T Ceramic capacitor, 1.0F, 10%, 50V, X7R, 1206 C6 (voltage mode) Murata GRM32DR61E106KA12L Ceramic capacitor, 10F, 10%, 25V, X5R, 1210 C7, C15, C18, C21, C24 Taiyo Yuden, TMK212BJ475KG Ceramic capacitors, 4.7F, 10%, 25V, X7R, 0805 C8 Taiyo Yuden, AMK107BJ226MA Ceramic capacitor, 2 x 22F, 20%, 4V, X5R, 0603 C9, C12, C13, C16, C19, C22 Taiyo Yuden, EMK105B7104KV Ceramic capacitors, 0.1F, 10%, 16V, X7R, 0402 C11 Sanyo, 16CE680AX Electrolytic capacitor, SMT 680F, 20%, 16V C14 Taiyo Yuden, JMK316BJ226KL Ceramic capacitor, 2 x 22F 10%, 6.3V, X5R, 1206 C17 Taiyo Yuden, JMK212BJ226KG Ceramic capacitor, 22F, 10%, 6.3V, X5R, 0805 C20 Taiyo Yuden, JMK316BJ226KL Ceramic capacitor, 2 x 22F, 10%, 6.3V, X5R, 1206 C23 Taiyo Yuden, JMK316BJ226KL Ceramic capacitor, 22F, 10%, 6.3V, X5R, 1206 C25 Taiyo Yuden, TMK105B7223KV Ceramic capacitor, 0.022F, 10%, 25V, X7R, 0402 D1 ON Semiconductor, MBR0540T1G Schottky diode, 40V, 0.5A, SOD123 D2 (the MAX8904 is protected for short-circuit fault at startup, D2 required only for short-circuit protection in normal operation) ON Semiconductor, MBR0540T1G Schottky diode, 40V, 0.5A, SOD123 Q1, Q2 Fairchild Semiconductor, FDS8962C Dual n-/p-MOSFETs, 30V, 8-pin SO R1 Yageo, RC0402FR-0710RL Resistor, SMT 10.0, 1/16W, 1%, 0402 R2 Vishay, WSL1206R0150FEA Resistor, 0.015, 1/4W, 1%, 1206 SMD R3 (the MAX8904 is protected for PCS to BSTFB short fault at startup, R3 required only for short PCS to BSTFB short-circuit protection in normal operation) Yageo, RC0402FR-0710RL Resistor, SMT 10.0, 1/16W, 1%, 0402 PCB Layout and Routing High switching frequencies and relatively large peak currents make the PCB layout a very important aspect of power converter design. Good design minimizes ground bounce, excessive EMI on the feedback paths, and voltage gradients in the ground plane, which can result in instability or regulation errors. A separate low-noise analog ground plane containing the reference, linear regulator, signal ground, and GND must connect to the power-ground plane at only one point to minimize the effects of power-ground currents. Connect GND to the exposed pad directly under the IC. Use multiple tightly spaced vias to the ground plane under the exposed pad to help cool the IC. Position the input capacitors from _IN to the power ground plane as close as possible to the IC. Connect the inductors and output capacitors as close as possible to the IC and keep the traces short, direct, and wide. Refer to the MAX8904 evaluation kit for the recommended PCB layout. ______________________________________________________________________________________ 43 MAX8904 Table 27. Recommended Component Specifications (See Figure 1) CMPI 3V3FB 3V3IN 3V3LX 3V3BST SCL SDA 1V2BST 1V2LX 1V2IN 1V2FB FLT PWREN TOP VIEW SHDN Pin Configuration 42 41 40 39 38 37 36 35 34 33 32 31 30 29 TEST 43 28 CMPO 1V8FB 44 27 GPIO7 1V8IN 45 26 GPIO6 1V8LX 46 25 GPIO5 1V8BST 47 24 GPIO4 BSTLX 48 23 GPIO3 22 GPIO2 BSTSW 49 MAX8904 BSTIN 50 21 GPIO1 20 GPIO0 BSTFB 51 19 GPIOPWR PCS 52 18 5V0BST CLSOUT 53 17 5V0LX CLSIN 54 + CS- 55 16 5V0IN 15 5V0FB ADJBST ADJLX1 9 10 11 12 13 14 LVRPWR OVGATE 8 LVROUT OVPWR 7 LVRIN5V 6 GND 5 REF 4 ADJFB 3 ADJIN 2 ADJLX2 1 RPGATE CS+ 56 CSOUT MAX8904 High-Efficiency Power-Management IC with I2C Control for 2-Cell Li+ Battery Operated Devices TQFN Package Information For the latest package outline information and land patterns, go to www.maxim-ic.com/packages. PACKAGE TYPE PACKAGE CODE DOCUMENT NO. 56 TQFN-EP T5677+2 21-0144 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 44 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2009 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX8904ETN+ MAX8904ETN+T