APV-16-24 - Mean Well

SPECIFICATION

MODEL APV-16-5 APV-16-12 APV-16-15 APV-16-24

DC VOLTAGE

RATED CURRENT

CURRENT RANGE

RATED POWER

OUTPUT

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME Note.6

HOLD UP TIME (Typ.)

VOLTAGE RANGE Note.4

FREQUENCY RANGE

EFFICIENCY (Typ.)

AC CURRENT

INPUT

INRUSH CURRENT(Typ.)

LEAKAGE CURRENT

SAFETY STANDARDS

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVER LOAD

OVER VOLTAGE

5V 12V 15V 24V

2.6A 1.25A 1A 0.67A

0 ~ 2.6A 0 ~ 1.25A 0 ~ 1A 0 ~ 0.67A

13W 15W 15W 16.08W

100mVp-p 120mVp-p 120mVp-p 150mVp-p

±5.0%

±1.0%

±2.0%

1500ms, 30ms / 230VAC 1500ms,30ms / 115VAC at full load

90 ~ 264VAC 127 ~ 370VDC

47 ~ 63Hz

76% 80% 81% 83%

5.75 ~ 6.75V 13.8 ~ 16V 17.5 ~ 21V 27.6 ~ 32.4V

0.3A/230VAC 0.5A/115VAC

COLD START 50A(twidth=185 s measured at 50% Ipeak) at 230VACμ

0.25mA / 240VAC

Above 105% rated output power

Protection type : Hiccup mode, recovers automatically after fault condition is removed

-30 ~ +70 (Refer to "Derating Curve")℃

20 ~ 90% RH non-condensing

-40 ~ +80 , 10 ~ 95% RH℃

±℃ ℃0.03%/ (0 ~ 50 )

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

77*40*29mm (L*W*H)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltage. Please check the static characteristics for more details.

5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.

7. The unit might not be suitable for lighting applications in EU countries. Please check with your local authorities for the possible use of the unit.

8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently

connected to the mains.

Protection type : Shut off o/p voltage, clamping by zener diode

16W Single Output Switching Power Supply

Constant voltage design

Universal AC input / Full range

Protections: Short circuit / Over load / Over voltage

Fully isolated plastic case

Cooling by free air convection

Small and compact size

ⅡClass power unit, no FG

Class 2 power unit

ass LPSP

IP30 design

Suitable for LED lighting and moving sign applications

100% full load burn-in test

Low cost, high reliability

2 years warranty

■Features :

APV-16 series

RIPPLE & NOISE (max.) Note.2

VOLTAGE TOLERANCE Note.3

ENVIRONMENT

SAFETY &

EMC

PROTECTION

20ms/230VAC 12ms/115VAC at full load

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

I/P-O/P:3.75KVAC

I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH℃

File Name:APV-16-SPEC 2015-05-28

1145.7K hrs min. MIL-HDBK-217F (25 )℃

0.1Kg; 120pcs/14Kg/1.06CUFT

EMC IMMUNITY

Compliance to EN55015,EN61000-3-2 Class A,EN61000-3-3

Compliance to EN61547,EN61000-4-2,3,4,5,6,8,11; light industry level(surge 2KV), criteria A

EMC EMISSION

LPS

110 SELV

IP30

UL8750,CSA C22.2 No.250.0-08, NECEEN61347-1,EN61347-2-13,EN62384 Independent,IP30 Approved

()Note.8

MAX. No. of PSUs on 16A

CIRCUIT BREAKER 13 units (circuit breaker of type B) / 22 units (circuit breaker of type C) at 230VAC