E5GN-R1TCAC/DC24 - Omron Electronics

Digital Temperature Controllers E5GN

Compact, Intelligent Temperature Controllers

H1/32 DIN sized controller saves panel

space, measures just 100 mm deep

HAccepts thermocouple, platinum RTD,

non-contact temperature sensor, and

analog temperature inputs

HAuto-tuning and self-tuning available;

functions can be used simultaneously

HHeating or heating/cooling control

HWater-resistant construction (NEMA 4X,

equivalent to IP66)

HConforms to UL, CSA, and IEC safety

standards as well as CE marking

H3-year warranty

Ordering Information

Optional communications and event input boards are shown on the following page.

JSTANDARD TEMPERATURE CONTROLLERS

Size Power Alarm points Output Part number

supply

voltage Thermocouple input Platinum RTD input

1/32 DIN 100 to ––– Relay E5GN-RTC AC100-240 E5GN-RP AC100-240

48(W) x 240 VAC Voltage (for driving SSR) E5GN-QTC AC100-240 E5GN-QP AC100-240

24 (H) x

100(D) mm 1 (See Note 1) Relay E5GN-R1TC AC100-240 E5GN-R1P AC100-240

100(D) mm Voltage (for driving SSR) E5GN-Q1TC AC100-240 E5GN-Q1P AC100-240

24 V ––– Relay E5GN-RTC AC/DC24 E5GN-RP AC/DC24

AC/DC Voltage (for driving SSR) E5GN-QTC AC/DC24 E5GN-QP AC/DC24

1 (See Note 1) Relay E5GN-R1TC AC/DC24 E5GN-R1P AC/DC24

Voltage (for driving SSR) E5GN-Q1TC AC/DC24 E5GN-Q1P AC/DC24

Note: 1. If the heating/cooling function is used, ALM1 will be used for control output; the alarm output will not be available.

2. Control output 2 for heating/cooling control is a relay output

JTEMPERATURE CONTROLLERS WITH COMMUNICATIONS

Size Power Communication Output Part number

supply

voltage type Thermocouple input Platinum RTD input

1/32 DIN 100 to RS-485 Relay E5GN-R03TC-FLK AC100-240 E5GN-R03P-FLK AC100-240

48(W) x 240 VAC Voltage (for driving SSR) E5GN-Q03TC-FLK AC100-240 E5GN-Q03P-FLK AC100-240

24 (H) x

100(D) mm 24 V Relay E5GN-R03TC-FLK AC/DC24 E5GN-R03P-FLK AC/DC24

100(D) mm AC/DC Voltage (for driving SSR) E5GN-Q03TC-FLK AC/DC24 E5GN-Q03P-FLK AC/DC24

E5GN E5GN

JINPUT RANGES

1800

1700

1600

1500

1400

1300

1200

1100

1000

900

800

700

600

500

400

300

200

100

–100

–200

Pt100 JPt100

Input type Platinum resistance thermometer

Name

850

Applicable standards by input type are as follows:

K, J, T, E, N, R, S, B: JIS C1602-1995

L: Fe-CuNi, DIN 43710-1985

U: Cu-CuNi, DIN 43710-1985

JPt100: JIS C1604-1989, JIS C1606-1989

Pt100: JIS C1604-1997, IEC751

Set value 1234

–200

500.0

–199.9

100.0

0.0

500.0

–199.9

100.0

0.0

Thermocouple ES1A Non-contact

Temperature Sensor Analog input

Usable in the

following

ranges by

scaling:

–1999 to 9999

or –199.9 to

999.9

0 to 50 mV

1800

1700

1600

1500

1400

1300

1200

1100

1000

900

800

700

600

500

400

300

200

100

–100

–200

Input type

Name KJTELUNRSB

K10 to

70°CK60 to

120°CK115 to

165°CK160 to

260°C

Set value 1234 567 89101112131415 16

–200

500.0

–20.0

1300

850

–100

400.0

–20.0

400

–200

600

850

–100

400

–200

1300

–200

1700

1800

100 70

120

165

260

0 17

400.0

–199.9

400.0

–199.9

Note: Lightly shaded ranges indicate default settings.

E5GN E5GN

Specifications

JRATINGS

Supply voltage 100 to 240 VAC, 50/60 Hz 24 VAC, 50/60 Hz/24 VDC

Operating voltage range 85% to 110% of rated supply voltage

Power consumption 7 VA 4 VA/2.5 W

Sensor input Thermocouple: K, J, T, E, L, U, N, R, S, B

Platinum resistance thermometer: Pt100, JPt100

Non-contact temperature sensor: 10 to 70_C, 60 to 120_C, 115 to 165_C, 160 to 260_C

Voltage input: 0 to 50 mV

Control output Relay output SPST-NO, 250 VAC, 2 A (resistive load), electrical life: 100,000 operations

Voltage output 12 VDC +15%/–20% (PNP), max. load current: 21 mA, with short-circuit protection circuit

Alarm output SPST-NO, 250 VAC, 1 A (resistive load), electrical life: 100,000 operations

Control method PID or ON/OFF control

Setting method Digital setting using front panel keys

Indication method 7-segment digital display and single-lighting indicator

Character height: PV: 7.0 mm; SV: 3.5 mm

Ambient operating temperature –10_C to 55_C (14°F to 131°F) with no condensation or icing

Storage temperature –25_C to 65_C (–13°F to 149°F) with no condensation or icing

Ambient humidity 25% to 85% RH

JCHARACTERISTICS

Indication accuracy Thermocouple: ±0.5% of indicated value or ±1_C, whichever greater, ±1 digit max. (See Note)

Platinum resistance thermometer: ±0.5% of indicated value or ±1_C, whichever greater, ±1 digit max.

Analog input: ±0.5% FS±1 digit max.

CT input: ±5% FS±1 digit max.

Hysteresis 0.1 to 999.9 EU (in units of 0.1 EU)

Proportional band (P) 0.1 to 999.9 EU (in units of 0.1 EU)

Integral time (I) 0 to 3999 s (in units of 1 s)

Derivative time (D) 0 to 3999 s (in units of 1 s)

Control period 1 to 99 s (in units of 1 s)

Manual reset value 0.0% to 100.0% (in units of 0.1%)

Alarm setting range -1999 to 9999 (decimal point position depends on input type)

Sampling period 500 ms

Insulation resistance 20 MΩ min. at 500 VDC

Dielectric strength 2000 VAC, 50 or 60 Hz for 1 min between different charging terminals

Vibration resistance 10 to 55 Hz, 10 m/s2 for 2 hours each in X, Y and Z directions

Shock resistance 300 m/s2, 3 times each in 3 axes, 6 directions (relay: 100 m/s2)

Weight Approx. 90 g; mounting bracket: Approx. 10 g

Protective structure Front panel: NEMA4X for indoor use (equivalent to IP66), rear case: IP20, terminals: IP00

Memory protection EEPROM non-volatile memory (number of writes: 100,000)

Note: The indication of K thermocouples in the -200 to 1300°C range, and T and N thermocouples at a temperature of -100°C or less, and U

and L thermocouples at any temperature is ±2°C±1 digit maximum. The indication of B thermocouples at a temperature of 400°C or

less is unrestricted.

The indication of R and S thermocouples at a temperature of 200°C or less is ±3°C±1 digit maximum.

(This table continues on the next page.)

E5GN E5GN

Specifications Table – continued from previous page

EMC Emission Enclosure: EN55011 Group 1 class A

Emission AC Mains: EN55011 Group 1 class A

Immunity ESD: EN61000-4-2: 4 kV contact discharge (level 2)

8 kV air discharge (level 3)

Immunity RF-interference: ENV50140: 10 V/m (amplitude modulated,

80 MHz to 1 GHz) (level 3)

10 V/m (pulse modulated, 900 MHz)

Immunity Conducted Disturbance: ENV50141: 10 V (0.15 to 80 MHz) (level 3)

Immunity Burst: EN61000-4-4: 2 kV power-line (level 3)

2 kV I/O signal-line (level 4)

Approved standards UL3121-1, CSA22.2 No. 14, E.B.1402C

Conforms to EN50081-2, EN50082-2, EN61010-1 (IEC61010-1)

JCOMMUNICATIONS SPECIFICATIONS

Transmission path connection Multiple points

Communications method (See Note) RS-485 (two-wire, half duplex)

Synchronization method Start-stop synchronization

Baud rate 1,200/2,400/4,800/9,600/19,200 bps

Transmission code ASCII

Data bit length (See Note) 7 or 8 bits

Stop bit length (See Note) 1 or 2 bits

Error detection Vertical parity (none, even, odd)

Frame check sequence (FCS): with SYSMAC WAY

Block check character (BCC): with CompoWay/F

Flow control Not available

Interface (See Note) RS-485

Retry function Not available

Communications buffer 40 bytes

Note: The baud rate, data bit length, stop bit length, or vertical parity can be individually set using the communications setting level.

Nomenclature

CMW STP OUT

Temperature unit No.1 display

Level key

Operation in-

dicators

No.2 display

Up key

Mode key Down key

E5GN E5GN

Dimensions

Unit: mm (inch)

Panel Cutout

* When carrying out maintenance on the E5GN, only the

terminal plate can be drawn out with the terminal leads still

attached.

48 (1.89)

36.8

(1.45)

(0.12) 100 (3.94)

44.8 (1.76)

48  number of units – 2.5

(1.89  number of units – 0.10)

60 (2.36) min.

(2.36)

min.

+1.0

+0.3

Mounted Separately

•Insert the Controller through the hole in the panel from the front and

push the adapter on from the rear. Push the adapter up to the back

of the panel ensuring that the controller is pushed all the way in,

removing any gap between the Controller, panel, and adapter.

Finally, use the two screws on the adapter to secure the unit in

place.

•To mount the E5GN so that it is waterproof, insert the waterproof

packing onto the E5GN.

•When two or more E5GN Controllers are mounted, make sure that

the surrounding temperature does not exceed the allowable

operating temperature ranges in the specifications.

Group Mounted

Mounting separately does not allow waterproofing.

(0.87)

(1.77)

(0.87)

(0.94)

(1.38)

(0.87)

+0.6

E5GN E5GN

Wiring Terminals

•The voltage output (control output) is not electrically insulated

from the internal circuits. When using a grounding thermocou-

ple, do not connect the control output terminals to the ground.

If the control output terminals are connected to the ground,

errors will occur in the measured temperature values as a

result of leakage current.

•Standard insulation is applied to the power supply I/O

sections. If reinforced insulation is required, connect the input

and output terminals to a device without any exposed

current-carrying parts or to a device with standard insulation

suitable for the maximum operating voltage of the power

supply I/O section.

Analog input

Input power supply

Two input power supplies are available:

100 to 240 VAC or 24 VAC/VDC (no polarity).

Relay output

Voltage output Alarm output

Control output

Cat. No. GCTC13 8/00 Specifications subject to change without notice. Printed in U.S.A.

OMRON ELECTRONICS, INC.

One East Commerce Drive

Schaumburg, IL 60173

1-800-55-OMRON

OMRON CANADA, INC.

885 Milner Avenue

Scarborough, Ontario M1B 5V8

416-286-6465