Data Sheet
June 1999
ORCA
®
Series 3C and 3T
Field-Programmable Gate Arrays
Features
■High-performance, cost-effective, 0.35 µm (OR3C) and
0.3 µm (OR3T) 4-level metal technology, (4- or 5-input
look-up table delay of 1.1 ns with -7 speed grade in
0.3 µm).
■Same basic architecture as lower-voltage, advanced
process technology Series 3 architectures. (See
ORCA
Series 3L FPGA documentation.)
■Up to 186,000 usable gates.
■Up to 452 user I/Os. (OR3Txxx I/Os are 5 V tolerant to
allow interconnection to both 3.3 V and 5 V devices,
selectable on a per-pin basis.)
■Pin selectable I/O clamping diodes provide 5 V or 3.3 V
PCI compliance and 5 V tolerance on OR3Txxx devices.
■Twin-quad programmable function unit (PFU) architec-
ture with eight 16-bit look-up tables (LUTs) pe r PFU,
organized in two nibbles for use in nibble- or byte-wide
functio ns. Allo ws f or mi x ed arithmetic and logic functio ns
in a single PFU.
■Nine user registers per PFU, one following each LUT,
plus one extra. All have programmable clock enable and
local set/reset, plus a global set/reset that can be dis-
abled per PFU.
■Flexible input structure (FINS) of the PFUs provides a
routabil ity enhan cement for LUTs w ith share d inputs an d
the logic flexibility of LUTs with independent inputs.
■F ast-carry logic and routing to adjacent PFUs for nibble-,
byte-wide, or longer arithmetic functions, with the option
to register the PFU carry-out.
■Softwired LUTs (SWL) allow fast cascading of up to
three levels of LUT logic in a single PFU for up to 40%
speed im provement.
■Supplemental logic and interconnect cell (SLIC) provides
3-statable buffers, up to 10-bit decoder, and
PAL
*-like
AND-OR with optional I NVERT in each programmable
logic cell (PLC), with over 50% sp eed improvement typi-
cal.
■Abundant hierarchical routing resources based on rout-
ing tw o data nib ble s and tw o control li nes per set pro vide
for faster place and route implementations and less rout-
ing delay.
■TTL or CMOS input levels programmable per pin fo r the
OR3Cxx (5.0 V) devices.
■Individually programmable drive capability:
12 mA sink/6 mA source or 6 mA sink/3 mA source.
■Built-in boundary scan (
IEEE
†1149.1 JTAG) and
TS_ALL testability function to 3-state all I/O pins.
■Enhance d system cl ock routing f or lo w sk ew, high-spe ed
clocks originating on-chip or at any I/O.
■Up to four ExpressCLK inputs allow extremely fast clock-
ing of si gnals on- and off-chip plus access to internal
general clock rout in g.
■StopCLK feature to glitchlessly stop/start ExpressCLKs
independently by user command.
■Progra mmable I/O (PIO) has:
— Fast-capture input latch and input flip-flop (FF) latch
for reduced input setup time and zero hold time.
— Capability to (de)multiplex I/O signals.
— Fast access to SLIC for decodes and
PAL
-like
functions.
— Output FF and two-signal function generator to
reduce CLK to output propagation delay.
— Fast ope n-drain dive capability
— Capability to register 3-state enable signal.
■Baseline FPGA family used in Series 3+ FPSCs (field
prog ra mmab le sy stem chips ) wh ich co mbine F PGA logic
and standard cell logic on one device.
*
PAL
is a trademark of Advanced Micro De vi ces, Inc.
†
IEEE
is a registered trademark of The Institute of Electrical and
Electronics Engineers, Inc.
Table 1.
ORCA
Series 3 (3C and 3T) FPGAs
‡The system gate counts range from a logic- only gate count to a gate count as sum ing 30% of the PFUs/SLICs being used as RAMs.
The logic-only gate count includes each PFU/SLIC (counted as 108 gates per PFU/SLIC), including 12 gates per LUT/FF pair (eight per
PFU), and 12 gates per SLIC/FF pair (one per PFU). Each of the four PIOs per PIC is counted as 16 gates (two FFs, fast-capture latch,
output logic, CLK drivers, and I/O buffers). PFUs used as RAM are counted at four gates per bit, with each PFU capable of implementing
a 32 x 4 RAM (or 512 gates) per PFU.
Device Syst em
Gates‡LUTs Registers Max User RAM User I/Os Array Size Process
Technology
OR3T20 36K 1152 1872 18K 196 12 x 12 0.3 µm/4 LM
OR3T30 48K 1568 2436 25K 228 14 x 14 0.3 µm/4 LM
OR3C/3T55 80K 2592 3780 42K 292 18 x 18 0.3 µm/4 LM
OR3C/3T80 116K 3872 5412 62K 356 22 x 22 0.3 µm/4 LM
OR3T125 186K 6272 8400 100K 452 28 x 28 0.3 µm/4 LM
Table of Contents
Contents Page Contents Page
2Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Features ......................................................................1
System-Level Features................................................6
Description...................................................................7
FPGA Overview ........................................................7
PLC Logic ..................................................................7
PIC Logic ...................................................................8
System Feature s .............. .........................................8
Routing ......................................................................8
Configuration .............................................................8
ORCA
Foundry Development System ......................9
Architecture .................................................................9
Programmable Logic Cells ........................................11
Programmable Function Unit ..................................11
Look-Up Table Operating Modes ............................13
Supplemental Logic and Interconnect Cell (SLIC) ..21
PLC Latches/Flip-Flops ...........................................25
PLC Routing Resources ..........................................27
PLC Architectural Description .................................34
Programmable Input/Output Cells.............................36
5 V Tolerant I/O .......................................................37
PCI Compliant I/O ...................................................37
Inputs ......................................................................38
Outputs ... .......................... .......................... .............41
PIC Routing Resources ...........................................44
PIC Architectural Description ..................................45
High-Level Routing Resources..................................47
Interquad Routing ....................................................47
Programmable Corner Cell Routing ........................48
PIC Interquad (MID) Routing ...................................49
Clock Distribution Network ........................................50
PFU Clock Sources ....................... ...... ....... .............50
Clock Distribution in the PLC Array .........................51
Clock Sources to the PLC Array .............................52
Clocks in the PICs ...................................................52
ExpressCLK Inputs .................................................53
Selecting Clock Input Pins ......................................53
Special Function Blocks ............................................54
Single Function Blocks ............................................54
Boundary Scan ........................................................57
Microprocessor Interface (MPI).................................64
PowerPC
System ....................................................65
i960
System ............................................................66
MPI Interface to FPGA ............................................67
MPI Setup and Control ............................................68
Programmable Clock Manager (PCM) ......................72
PCM Registers ........................................................73
Delay-Locked Loop (DLL) Mode .............................75
Phase-Locked Loop (PLL) Mode ............................76
PCM/FPGA Internal Interface .................................79
PCM Operation .......................................................79
PCM Detailed Programming ...................................80
PCM Applications ....................................................83
PCM Cautions ........................................................ 84
FPGA States of Operation........................................ 85
Initiali za tion ...... ....... ...... ....... ...... ....... ...... ....... ...... ... 85
Configuration .......................................................... 86
Start-Up .................................................................. 87
Reconfiguration ...................................................... 88
Partial Reconfiguration ........................................... 88
Other Configuration Options ................................... 88
Configuration Data Format ...................................... 89
Using
ORCA
Foundry to Generate
Configuration RAM Data ....................................... 89
Configuration Data Frame ...................................... 89
Bit Stream Error Checking ...................................... 91
FPGA Configuration Modes...................................... 92
Master Paralle l Mode ............................................. 92
Master Serial Mod e ...... ....... ................................... 93
Asynchronous Peripheral Mode ............................. 94
Microprocessor Interface (MPI) Mode .................... 94
Slave Serial Mode .................................................. 97
Slave Parallel Mode ............................................... 97
Daisy-Chaining ....................................................... 98
Daisy-Cha ini ng with Bound ary Scan ...................... 99
Absolute Maximum Ratings.................................... 100
Recommended Operating Conditions .................. 100
Electrical Characteristics........................................ 101
Timing Characteristics............................................ 103
Description ........................................................... 103
PFU Timing .... ....... ...... ....... ...... ....... ...... ....... ...... . 104
PLC Timing ........................................................... 111
SLIC Timing .......................................................... 111
PIO Timing ............. ...... ....... ...... ....... ...... ....... ...... . 112
Special Function Blocks Timing ........................... 115
Clock Timing ......................................................... 123
Configuration Timing ............................................ 133
Readback Timing ................................................. 142
Input/Output Buffer Measurement Conditions ........ 143
Output Buffer Characteristics ................................. 144
OR3Cxx ................................................................ 144
OR3Txxx .............................................................. 145
Estimating Power Dissipation................................. 146
OR3Cxx ................................................................ 146
OR3Txxx (Preliminary Information) ...................... 147
Pin Information ....................................................... 149
Pin Descriptions ................................................... 149
Package Compatibility .......................................... 153
Compatibility with OR2C/TxxA Series .................. 154
Package Thermal Characteristics........................... 194
ΘJA ............ ...... ....... ...... ........................................ 194
ψJC ...................................................................... 194
ΘJC ...................................................................... 194
ΘJB ...................................................................... 194
FPGA Maximum Junction Temperature ............... 195
Table of Contents
Contents Page Contents Page
Lucent Technologies Inc. 3
ORCA
Series 3C and 3T FPGAs
J une 1999
Data Sheet
Package Coplanarity ...............................................196
Package Parasitics..................................................196
Package Outline Diagrams......................................197
Terms and Definitions ...........................................197
208-Pin SQFP .......................................................198
208-Pin SQFP2 .....................................................199
240-Pin SQFP .......................................................200
240-Pin SQFP2 .....................................................201
256-Pin PBGA .......................................................202
352-Pin PBGA .......................................................203
432-Pin EBGA .......................................................204
600-Pin EBGA .......................................................205
Ordering Information................................................206
Index........................................................................207
Tables
Table 1.
ORCA
Series 3 (3C and 3T) FPGAs ............2
Table 2.
ORCA
Series 3 System Performance ..........6
Table 3. Look-Up Table Operating Modes ...............13
Table 4. Control Input Functionality ..........................14
Table 5. Ripple Mode Equality Comparator
Functions and Outputs ............................................18
Table 6. SLIC Modes ................................................21
Table 7. Configuration RAM Controlled
Latch/Flip-Flop Operation ........................................25
Table 8. Inter-PLC Routing Resources .....................31
Table 9. PIO Options ................................................37
Table 10. PIO Logic Options ....................................43
Table 11. PIO Register Control Signals ....................43
Table 12. Readback Options ....................................54
Table 13. Boundary-Scan Instructions .....................58
Table 14. Boundary-Scan ID Code ...........................59
Table 15. TAP Controller Input/Outputs ...................61
Table 16.
PowerPC
/MPI Configuration .....................65
Table 17.
i960
/MPI Configuration .............................66
Table 18. MPI Internal Interface Signals ..................67
Table 19. MPI Setup and Control Registers .............68
Table 20. MPI Setup and Control Registers
Description ...............................................................68
Table 21. MPI Control Register 2 .............................69
Table 22. Status Register .........................................70
Table 23. Device ID Code ........................................71
Table 24. Series 3 Family and Device ID Values .....71
Table 25.
ORCA
Series 3 Device ID Descriptions ....71
Table 26. PCM Registers .........................................73
Table 27. DLL Mode Delay/1x Duty Cycle
Programming Values ...............................................75
Table 28. DLL Mode Delay/2x Duty Cycle
Programming Values ...............................................76
Table 29. PCM Oscillator Frequency Range 3Txxx .78
Table 30. PCM Oscillator Frequency Range 3Cxx ...78
Table 31. PCM Control Registers .............................80
Table 32. Configuration Frame Format and
Contents .................................................................. 90
Table 33. Configuration Frame Size .........................91
Table 34. Configuration Modes ................................92
Table 35. Absolute Maximum Ratings ....................100
Table 36. Recommended Operating Conditions ....100
Table 37. Electrical Characteristics ........................101
Table 38. Derating for Commercial Devices
(OR3Cxx) ..............................................................103
Table 39. Derating for Industrial Devices (OR3Cxx) 103
Table 40. Derating for Commercial/Industrial
Devices (OR3Txxx) ...............................................103
Table 41. Combinatorial PFU Timing
Characteristics .......................................................104
Table 42. Sequential PFU Timing Characteristics ..106
Table 43. Ripple Mode PFU Timing
Characteristics .......................................................107
Table 44. Synchronous Memory Write
Characteristics .......................................................109
Table 45. Synchronous Memory Read
Characteristics .......................................................110
Table 46. PFU Output MUX and Direct Routing
Timing Characteristics ...........................................111
Table 47. Supplemental Logic and Interconnect
Cell (SLIC) Timing Characteristics ........................111
Table 48. Programmable I/O (PIO) Timing
Characteristics .......................................................112
Table 49. Microprocessor Interface (MPI) Timing
Characteristics .......................................................115
Table 50. Programmable Clock Manager (PCM)
Timing Characteristics (Preliminary Information) ..121
Table 51. Boundary-Scan Timing Characteristics ..122
Table 52. ExpressCLK (ECLK) and Fast Clock
(FCLK) Timing Characteristics ..............................123
Table 53. General-Purpose Clock Timing
Characteristics (Internally Generated Clock) .........124
Table 54. OR3Cxx ExpressCLK to Output Delay
(Pin-to-Pin) ............................................................125
Table 55. OR3Cxx Fast Clock (FCLK) to Output
Delay (Pin-to-Pin) ..................................................126
Table 56. OR3Cxx General System Clock (SCLK)
to Output Delay (Pin-to-Pin) ..................................127
Table 57. OR3C/Txxx Input to ExpressCLK (ECLK)
Fast-Capture Setup/Hold Time (Pin-to-Pin) ..........128
Table 58. OR3C/Txxx Input to Fast Clock
Setup/Hold Time (Pin-to-Pin) ................................130
Table 59. OR3C/Txxx Input to General System
Clock (SCLK) Setup/Hold Time (Pin-to-Pin) ..........132
Table 60. General Configuration Mode Timing
Characteristics .......................................................133
Table 61. Master Serial Configuration Mode Timing
Table of Contents
Contents Page Contents Page
4Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Characteristics ......................................................136
Table 62. Master Parallel Configuration Mode Timing
Characteristics ......................................................137
Table 63. Asynchronous Peripheral Configuration Mode
Timing Characteristics ...........................................138
Table 64. Slave Serial Configuration Mode Timing
Characteristics ......................................................139
Table 65. Slave Parallel Configuration Mode
Timing Characteristics ...........................................140
Table 66. Readback Timing Characteristics ...........142
Table 67. Pin Descriptions ......................................149
Table 68.
ORCA
I/Os Summary .............................153
Table 69. Series 3 ExpressCLK Pins .....................154
Table 70. OR3T20, OR3T30, OR3C/T55,
OR3C/T80, and OR3T125 208-Pin
SQFP/SQFP2 Pinout ............................................155
Table 71. OR3T20, OR3T30, OR3C/T55,
OR3C/T80, and OR3T125 240-Pin
SQFP/SQFP2 Pinout ............................................161
Table 72. OR3T20, OR3T30, and OR3C/T55
256-Pin PBGA Pinout ............................................168
Table 73. OR3T20, OR3T30, OR3C/T55,
OR3C/T80, and OR3T125 352-Pin PBGA Pinout .172
Table 74. OR3C/T80 and OR3T125 432-Pin
EBGA Pinout .........................................................182
Table 75. OR3T125 600-Pin EBGA Pinout ............187
Table 76. Plastic Package Thermal
Characteristics for the
ORCA
Series .....................195
Table 77. Package Coplanarity ..............................196
Table 78. Package Parasitics .................................196
Table 79. Voltage Options ......................................206
Table 80. Temperature Options .............................206
Table 81. Package Options ....................................206
Table 82.
ORCA
Series 3 Package Matrix .............206
Table 83. Speed Grade Options .............................206
Figures
Figure 1. OR3C/T55 Array ........................................10
Figure 2. PFU Ports ..................................................11
Figure 3. Simplified PFU Diagram ............................12
Figure 4. Simplified F4 and F5 Logic Modes ............14
Figure 5. Softwired LUT Topology Examples ...........15
Figure 6. Ripple Mode ..............................................16
Figure 7. Counter Submode .....................................17
Figure 8. Multiplier Submode ....................................18
Figure 9. Memory Mode ...........................................19
Figure 10. Memory Mode Expansion Example—
128 x 8 RAM ...........................................................20
Figure 11. SLIC All Modes Diagram .........................22
Figure 12. Buffer Mode .............................................22
Figure 13. Buffer-Buffer-Decoder Mode ...................23
Figure 14. Buffer-Decoder-Buffer Mode ...................23
Figure 15. Buffer-Decoder-Decoder Mode ...............24
Figure 16. Decoder Mode .........................................24
Figure 17. Latch/FF Set/Reset Configurations .........26
Figure 18. Configurable Interconnect Point ..............27
Figure 19. Single PLC View of Inter-PLC Route
Segments ................................................................28
Figure 20. Multiple PLC View of Inter-PLC Routing .32
Figure 21. PLC Architecture .....................................35
Figure 22. OR3C/Txxx Programmable Input/Output
(PIO) Image from
ORCA
Foundry ...........................36
Figure 23. Fast-Capture Latch and Timing ...............39
Figure 24. PIO Input Demultiplexing .........................40
Figure 25. Output Multiplexing (OUT1OUT2 Mode) .42
Figure 26. Output Multiplexing
(OUT2OUTREG Mode) ...........................................42
Figure 27. PIC Architecture ......................................46
Figure 28. Interquad Routing ....................................47
Figure 29. hIQ Block Detail .......................................48
Figure 30. Top (TMID) Routing .................................49
Figure 31. PFU Clock Sources .................................50
Figure 32.
ORCA
Series 3 System Clock
Distribution Overv iew ................ ....... ...... ....... ...... ....51
Figure 33. PIC System Clock Spine Generation ......52
Figure 34. ExpressCLK and Fast Clock Distribution 53
Figure 35. Top CLKCNTRL Function Block ..............56
Figure 36. Printed-Circuit Board with Boundary-
Scan Circuitry ..........................................................57
Figure 37. Boundary-Scan Interface .........................58
Figure 38.
ORCA
Series Boundary-Scan Circuitry
Functional Diagram .................................................60
Figure 39. TAP Controller State Transition Diagram 61
Figure 40. Boundary-Scan Cell ................................62
Figure 41. Instruction Register Scan Timing
Diagram ...................................................................63
Figure 42. MPI Block Diagram ..................................64
Figure 43.
PowerPC
/MPI ..........................................65
Figure 44.
i960
/MPI ..................................................66
Figure 45. PCM Block Diagram ................................72
Figure 46. PCM Functional Block Diagram ..............74
Figure 47. ExpressCLK Delay Minimization Using
the PCM ..................................................................76
Figure 48. Clock Phase Adjustment Using the PCM 83
Figure 49. FPGA States of Operation .......................85
Figure 50. Initialization/Configuration/Start-Up
Waveforms ..............................................................86
Figure 51. Start-Up Waveforms ................................88
Figure 52. Serial Configuration Data Format—
Autoincrement Mode ...............................................90
Figure 53. Serial Configuration Data Format—
Table of Contents
Contents Page Contents Page
Lucent Technologies Inc. 5
ORCA
Series 3C and 3T FPGAs
J une 1999
Data Sheet
Explicit Mode ...........................................................90
Figure 54. Master Parallel Configuration Schematic 92
Figure 55. Master Serial Configuration Schematic ...93
Figure 56. Asynchronous Peripheral Configuration ..94
Figure 57.
PowerPC
/MPI Configuration Schematic ..95
Figure 58.
i960
/MPI Configuration Schematic ..........95
Figure 59. Configuration Through MPI .....................95
Figure 60. Readback Through MPI ..........................96
Figure 61. Slave Serial Configuration Schematic .....97
Figure 62. Slave Parallel Configuration Schematic ..97
Figure 63. Daisy-Chain Configuration Schematic .....98
Figure 64. Combinatorial PFU Timing ....................105
Figure 65. Synchronous Memory Write
Characteristics ......................................................109
Figure 66. Synchronous Memory Read Cycle ........110
Figure 67. MPI
PowerPC
User Space Read Timing 117
Figure 68. MPI
PowerPC
User Space Write Timing 117
Figure 69. MPI
PowerPC
Internal Read Timing .....118
Figure 70. MPI
PowerPC
Internal Write Timing ......118
Figure 71. MPI
i960
User Space Read Timing .......119
Figure 72. MPI
i960
User Space Write Timing .......119
Figure 73. MPI
i960
Internal Read Timing ..............120
Figure 74. MPI
i960
Internal Write Timing ..............120
Figure 75. Boundary-Scan Timing Diagram ...........122
Figure 76. ExpressCLK to Output Delay ................125
Figure 77. Fast Clock to Output Delay ...................126
Figure 78. System Clock to Output Delay ..............127
Figure 79. Input to ExpressCLK Setup/Hold Time ..129
Figure 80. Input to Fast Clock Setup/Hold Time .....131
Figure 81. Input to System Clock Setup/Hold Time 132
Figure 82. General Configuration Mode Timing
Diagram .................................................................135
Figure 83. Master Serial Configuration Mode
Timing Diagram .....................................................136
Figure 84. Master Parallel Configuration Mode
Timing Diagram .....................................................137
Figure 85. Asynchronous Peripheral Configuration
Mode Timing Diagram ...........................................138
Figure 86. Slave Serial Configuration Mode
Timing Diagram .....................................................139
Figure 87. Slave Parallel Configuration Mode
Timing Diagram .....................................................140
Figure 88. Readback Timing Diagram ....................142
Figure 89. ac Test Loads ........................................143
Figure 90. Output Buffer Delays .............................143
Figure 91. Input Buffer Delays ................................143
Figure 92. Sinklim (TJ = 25 °C, VDD = 5.0 V) ..........144
Figure 93. Slewlim (TJ = 25 °C, VDD = 5.0 V) .........144
Figure 94. Fast (TJ °C, VDD = 5.0 V) ......................144
Figure 95. Sinklim (TJ = 125 °C, VDD = 4.5 V) ........144
Figure 96. Slewlim (TJ = 125 °C, VDD = 4.5 V) .......144
Figure 97. Fast (TJ = 125 °C, VDD = 4.5 V) .......... ..14 4
Figure 98. Sinklim (TJ = 25 °C, VDD = 3.3 V) ..........145
Figure 99. Slewlim (TJ = 25 °C, VDD = 3.3 V) .........145
Figure 100. Fast (TJ = 25 °C, VDD = 3.3 V) ............14 5
Figure 101. Sinklim (TJ = 125 °C, VDD = 3.0 V) ......145
Figure 102. Slewlim (TJ = 125 °C, VDD = 3.0 V) .....145
Figure 103. Fast (TJ = 125 °C, VDD = 3.0 V) ..........145
Figure 104. Package Parasitics ..............................196
66 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
System-Level Features
System-level features reduce glue logic requirements
and make a system on a chip possible. These features
in the
ORCA
Series 3 include:
■Full PCI local bus compliance.
■Dual-use microprocessor interface (MPI) can be
used for configuration, readback, device control, and
device status, as well as f or a general-purpose inter-
face to the FPGA. Glueless interface to
i960
* and
PowerPC
† processors with user-configurable
address space provided.
■P arallel readback of configuration data capability with
the built-in microprocessor interface.
■Programmable clock manager (PCM) adjusts clock
phase and duty cycle for input clock rates from
5 MHz to 120 MHz. The PCM ma y be combined with
FPGA logic to create complex functions, such as dig-
ital phase-locked loops (DPLL), frequency counters,
and frequency synthesizers or clock doublers. Two
PCMs are provided per device.
■True, internal, 3-state, bidirectional buses with simple
control provided by the SLIC .
■32 x 4 RAM per PFU, configurable as single- or dual-
port at >176 MHz. Create large, fast RAM/ROM
blocks (128 x 8 in only eight PFUs) using the SLIC
decoders as bank drivers.
*
i960
is a registered trademark of Intel Corporation.
†
PowerPC
is a registered trademark of International Business
Machines Corporation.
Table 2.
ORCA
Series 3 System Performance
1. Implemented using 8 x 1 multiplier mode (unpipelined), register-to-register, two 8-bit inputs, one 16-bit output.
2. Implemented using two 32 x 12 ROM s and one 12-bit adder, one 8-bit input, one fixed operand, one 16-bit output.
3. Implemented using 8 x 1 multiplier mode (fully pipelined), two 8-bit inputs, one 16-bit output (7 of 15 PFUs contain only pipelining registers).
4. Implemented using 32 x 4 RAM mode with read data on 3-state buffer to bidirectional read/write bus.
5. Implemented using 32 x 4 dual-port RAM mode.
6. Implemented in one partially occupied SLIC with decoded output set up to CE in same PLC.
7. Implemented in five partially occupied SLICs.
Parameter # PFUs Speed Unit
-4 -5 -6 -7
16-bit Loadable Up/Down Counter 2 78 102 131 168 MHz
16-bit Accumulator 2 78 102 131 168 MHz
8 x 8 Parallel Multiplier:
Multiplier Mode, Unpipelined1
ROM Mode, Unpipelined2
Multiplier Mode, Pipelined3
11.5
8
15
19
51
76
25
66
104
30
80
127
38
102
166
MHz
MHz
MHz
32 x 16 RAM (synchronous):
Single-port, 3-state Bus4
Dual-port54
497
127 127
166 151
203 192
253 MHz
MHz
128 x 8 RAM (synchronous):
Single-port, 3-state Bus4
Dual-port58
888
88 116
116 139
139 176
176 MHz
MHz
8-bit Address Decode (internal):
Using Softwired LUTs
Using SLICs60.25
04.87
2.35 3.66
1.82 2.58
1.23 2.03
0.99 ns
ns
32-bit Address Decode (internal):
Using Softwired LUTs
Using SLICs72
016.06
6.91 12.07
5.41 9.01
4.21 7.03
3.37 ns
ns
36-bit Parity Check (internal) 2 16.06 12.07 9.01 7.03 ns
Lucent Technologies Inc. 7
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Description
FPGA Overview
The
ORCA
Series 3 FPGAs are a new generation of
SRAM -based FPGAs built on the successful OR2C/
TxxA FPGA Series from Lucent Technologies Micro-
electronics Group, with enhancements and innovations
geared toward today’s high-speed designs and tomor-
row’s systems on a single chip . Designed from the start
to be synthesis friendly and to reduce place and route
times while maintaini ng the complete rou tability of the
ORCA
2C/2T devices, Series 3 more than doubles the
logic av ailable in each logic b lock and incorporates sys-
tem-level features that can further reduce logic require-
ments and increase system speed.
ORCA
Ser ies 3
devices contain many new patented enhancements
and are offered in a v ariety of packages, speed grades,
and temperature ranges.
The
ORCA
Series 3 FPGAs consist of three basic ele-
ments: programmable logic cells (PLCs), programma-
ble input/output cells (PICs), and system-le v el features.
An array of PLCs is surrounded by PICs. Each PLC
contains a programmable function unit (PFU), a sup-
plemental logic and interconnect cell (SLIC), local rout-
ing resources, and configuration RAM. Most of the
FPGA logic is performed in the PFU, but decoders,
PAL
-like functions, and 3-state buffering can be per-
formed in the SLIC. The PICs provide device inputs
and outputs and can be used to register signals and to
perform input demultiplexing, output multiplexing, and
other functions on two output signals. Some of the sys-
tem-level functions include the new microprocessor
interface (MPI) and the programmable cloc k manager
(PCM).
PLC Logic
Each PFU within a PLC contains eight 4-input (16-bit)
look-up tables (LUTs), eight latches/flip-flops (FFs),
and one additional flip-flop that ma y be used indepen-
dently or with arithmetic functions.
The PFU is organized in a twin-quad fashion: two sets
of four LUTs and FFs that can be controlled indepen-
dently. LUTs may also be combined for use in arith-
metic functions using fast-carry chain logic in either
4-bit or 8-bit modes. The carry-out of either mode may
be registered in the ninth FF for pipelining. Each PFU
may also be configured as a synchronous 32 x 4 sin-
gle- or dual-port RAM or ROM. The FFs (or latches)
may obtain input from LUT outputs or directly from
invertible PFU inputs, or they can be tied high or tied
low. The FFs also have pr ogrammable clock polari ty,
clock enables, and local set/reset.
The SLIC is connected to PLC routing resources and to
the outputs of the PFU . It contains 3-state, bidirectional
buff ers and logic to perf orm up to a 10-bit AND function
for decoding, or an AND-OR with optional INVERT
(A OI) to perform
PAL
-like functions. The 3-state driv ers
in the SLIC and their direct connections to the PFU out-
puts make fast, true 3-state buses possible within the
FPGA, reducing required routing and allowing for real-
world system performance.
88 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Description (continued)
PIC Logic
Series 3 PIC addresses the demand for ever-increas-
ing system clock speeds. Each PIC contains four pro-
grammable inputs/outputs (PIOs) and routing
resources. On the input side, each PIO contains a fast-
capture latch that is clocked by an ExpressCLK. This
latch is followed by a latch/FF that is clocked by a sys-
tem clock from the internal general clock routing. The
combination provides for very low setup requirements
and zero hold times for signals coming on-chip. It may
also be used to demultiplex an input signal, such as a
multiplexed address/data signal, and register the sig-
nals without explicitly building a demultiplexer. Two
input signals are available to the PLC array from each
PIO, and the
ORCA
2C/2T capability to use any input
pin as a clock or other global input is maintained.
On the output side of each PIO, two outputs from the
PLC array can be routed to each output flip-flop, and
logic can be associated with each I/O pad. The output
logic associated with each pad allows for multiplexing
of output signals and other functions of two output sig-
nals.
The output FF in combination with output signal multi-
plexing, is particularly useful for registering address
signals to be multiplexed with data, allowing a full clock
cycle for the data to propagate to the output. The I/O
buffer associated with each pad is very similar to the
ORCA
2C/2T Series buffer with a new, f ast, open-drain
option for ease of use on system buses.
System Features
Series 3 also provides system-level functionality by
means of its dual-use microprocessor interface and its
innovative programmable clock manager. These func-
tional blocks allow for easy glueless system interfacing
and the capability to adjust to varying conditions in
today’s high-speed systems.
Routing
The abundant routing resources of the
ORCA
Series 3
FPGAs are organized to route signals individually or as
buses with related control signals. Clocks are routed on
a low-skew, high-speed distribution network and may
be sourced from PLC logic, externally from any I/O
pad, or from the very fast ExpressCLK pins. Express-
CLKs may be glitchlessly and independently enabled
and disabled with a programmable control signal using
the new StopCLK feature. The improved PIC routing
resources are now similar to the patented intra-PLC
routing resources and provide great fle xibility in moving
signals to and from the PIOs. This flexibility translates
into an improved capability to route designs at the
required speeds when the I/O signals hav e been lock ed
to specific pins.
Configuration
The FPGA’s functionality is determined by internal
configuration RAM. The FPGA’s internal initialization/
configuration circuitry loads the configuration data at
powerup or under system control. The RAM is loaded
by using one of several configuration modes. The con-
figuration data resides e xternally in an EEPROM or any
other storage media. Serial EEPROMs provide a sim-
ple, low pin count method for configuring FPGAs. A
new, easy method for configuring the devices is
through the microprocessor interface.
Lucent Technologies Inc. 9
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Description (continued)
ORCA
Foundry Dev elopment System
The
ORCA
Foundry Development System is used to
process a design from a netlist to a configured FPGA.
This system is used to map a design onto the
ORCA
architecture and then place and route it using
ORCA
F oundry’ s timing-driven tools. The de velopment system
also includes interf aces to, and libraries for, other popu-
lar CAE tools f or design entry, synthesis, simulation,
and timing analysis.
The
ORCA
F oundry De velopment System interf aces to
front-end design entry tools and provides the tools to
produce a configured FPGA. In the design flow, the
user defines the functionality of the FPGA at two points
in the design flow: at design entry and at the bit stream
generation stage.
F ollowing design entry, the de v elopment system’ s map ,
place, and route tools translate the netlist into a routed
FPGA. A static timing analysis tool is provided to deter-
mine device speed and a back-annotated netlist can be
created to allow simulation. Timing and simulation out-
put files from
ORCA
Foundry are also compatible with
many third-party analysis tools. Its bit stream generator
is then used to generate the configuration data which is
loaded into the FPGA’s internal configuration RAM.
When using the bit stream generator, the user selects
options that aff ect the functionality of the FPGA. Com-
bined with the front-end tools,
ORCA
Foundry pro-
duces configuration data that implements the various
logic and routing options discussed in this data sheet.
Architecture
The
ORCA
Series 3 FPGA comprises three basic ele-
ments: PLCs, PICs, and system-level functions. Figure
1 shows an array of programmable logic cells (PLCs)
surrounded by programmable input/output cells (PICs).
Also shown are the interquad routing blocks (hIQ, vIQ)
present in Series 3. System-le vel functions (located in
the corners of the array) and the routing resources and
configuration RAM are not shown in Figure 1.
The OR3C/T55 arr a y in Figure 1 has PLCs arranged in
an array of 18 rows and 18 columns. The location of a
PLC is indicated by its row and column so that a PLC in
the second row and the third column is R2C3. PICs are
located on all four sides of the FPGA between the
PLCs and the device edge. PICs are indicated using
PT and PB to designate PICs on the top and bottom
sides of the array, respectiv ely, and PL and PR to des-
ignate PICs along the left and right sides of the array,
respectively. The position of a PIC on an edge of the
array is indicated by a number, counting from left to
right for PT and PB and top to bottom for PL and PR
PICs.
Each PIC contains routing resources and f our program-
mable I/Os (PIOs). Each PIO contains the necessary
I/O buffers to interface to bond pads. PIOs in Series 3
FPGAs also contain input and output FFs, fast open-
drain capability on output buffers, special output logic
functions, and signal multiplexing/demultiplexing capa-
bilities.
PLCs comprise a programmable function unit (PFU), a
supplemental logic and interconnect cell (SLIC), and
routing resources . The PFU is the main logic element
of the PLC, containing elements for both combinatorial
and sequential logic. Combinatorial logic is done in
look-up tables (LUTs) located in the PFU . The PFU can
be used in different modes to meet different logic
requirements. The LUT’s twin-quad architecture pro-
vides a configurable medium-/large-grain architecture
that can be used to implement from one to eight inde-
pendent combinatorial logic functions or a large num-
ber of comple x logic functions using multiple LUTs. The
flexibility of the LUT to handle wide input functions, as
well as multiple smaller input functions, maximizes the
gate count per PFU while increasing system speed.
The LUTs can be programmed to operate in one of
three modes: combinatorial, ripple, or memory. In com-
binatorial mode, the LUTs can realize any 4- or 5-input
logic function and many multilevel logic functions using
ORCA
’s softwired LUT (SWL) connections. In ripple
mode, the high-speed carry logic is used for arithmetic
functions, comparator functions, or enhanced data path
functions. In memory mode, the LUTs can be used as a
32 x 4 synchronous read/write or read-only memory, in
either single- or dual-port mode.
10 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Architecture (continued)
5-4489(F)
Figure 1. OR3C/T55 Array
VI
PL9 PL8 PL7 PL6 PL5 PL4 PL3 PL2 PL1PL13 PL12 PL11
PR12PR11PR9PR8PR7PR6PR5PR4PR3PR2PR1 PR13 PR18PR17PR16PR15PR14RMIDPR10
PT1 PT2 PT3 PT4 PT5 PT6 PT7 PT8 PT9 PT11 PT12
R1C1 R1C2 R1C3 R1C4 R1C5 R1C6 R1C7 R1C8 R1C9 R1C10 R1C18R1C17R1C16R1C15R1C14R1C13R1C12R1C11
PT13 PT14 PT15 PT16 PT17 PT18
PB1 PB2 PB3 PB4 PB5 PB6 PB7 PB8 PB9 PB10 PB11 PB12
PL18 PL17 PL16 PL15 PL14
PB13 PB14 PB15 PB16 PB17 PB18
PL10
BMID
PT10
vIQ
R2C1 R2C2 R2C3 R2C4 R2C5 R2C6 R2C7 R2C8 R2C9 R2C10
R3C1 R3C2 R3C3 R3C4 R3C5 R3C6 R3C7 R3C8 R3C9 R3C10
R4C1 R4C2 R4C3 R4C4 R4C5 R4C6 R4C7 R4C8 R4C9 R4C10
R5C1 R5C2 R5C3 R5C4 R5C5 R5C6 R5C7 R5C8 R5C9 R5C10
R6C1 R6C2 R6C3 R6C4 R6C5 R6C6 R6C7 R6C8 R6C9 R6C10
R7C1 R7C2 R7C3 R7C4 R7C5 R7C6 R7C7 R7C8 R7C9 R7C10
R8C1 R8C2 R8C3 R8C4 R8C5 R8C6 R8C7 R8C8 R8C9 R8C10
R9C1 R9C2 R9C3 R9C4 R9C5 R9C6 R9C7 R9C8 R9C9 R9C10
R10C1 R10C2 R10C3 R10C4 R10C5 R10C6 R10C7 R10C8 R10C9 R10C10
R2C18R2C17R2C16R2C15R2C14R2C13R2C12R2C11
R3C18R3C17R13C16R3C15R3C14R3C13R3C12R3C11
R4C18R4C17R4C16R4C15R4C14R4C13R4C12R4C11
R5C18R5C17R5C16R5C15R5C14R5C13R5C12R5C11
R6C18R6C17R6C16R6C15R6C14R6C13R6C12R6C11
R7C18R7C17R7C16R7C15R7C14R7C13R7C12R7C11
R8C18R8C17R8C16R8C15R8C14R8C13R8C12R8C11
R9C18R9C17R9C16R9C15R9C14R9C13R9C12R9C11
R10C18R10C17R10C16R10C15R10C14R10C13R10C12R10C11
R18C18R18C17R18C16R18C15R18C14R18C13R18C12R18C11
R17C18R17C17R17C16R17C15R17C14R17C13R17C12R17C11
R16C18R16C17R16C16R16C15R16C14R16C13R16C12R16C11
R15C18R15C17R15C16R15C15R15C14R15C13R15C12R15C11
R14C18R14C17R14C16R14C15R14C14R14C13R14C12R14C11
R13C18R13C17R13C16R13C15R13C14R13C13R13C12R13C11
R12C18R12C17R12C16R12C15R12C14R12C13R12C12R12C11
R11C18R11C17R11C16R11C15R11C14R11C13R11C12R11C11
R18C10R18C9R18C8R18C7R18C6R18C5R18C4R18C3R18C2R18C1
R17C10R17C9R17C8R17C7R17C6R17C5R17C4R17C3R17C2R17C1
R16C10R16C9R16C8R16C7R16C6R16C5R16C4R16C3R16C2R16C1
R15C10R15C9R15C8R15C7R15C6R15C5R15C4R15C3R15C2R15C1
R14C10R14C9R14C8R14C7R14C6R14C5R14C4R14C3R14C2R14C1
R13C10R13C9R13C8R13C7R13C6R13C5R13C4R13C3R13C2R13C1
R12C10R12C9R12C8R12C7R12C6R12C5R12C4R12C3R12C2R12C1
R11C10R11C9R11C8R11C7R11C6R11C5R11C4R11C3R11C2R11C1
hIQ
TMID
LMID
Lucent Technologies Inc. 11
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells
The programmable logic cell (PLC) consists of a pro-
grammable function unit (PFU), a supplemental logic
and interconnect cell (SLIC), and routing resources. All
PLCs in the array are functionally identical with only
minor differences in routing connectivity for improved
routability. The PFU, which contains eight 4-input LUTs,
eight latches/FFs, and one FF f or logic implementation,
is discussed in the ne xt section, followed by discus-
sions of the SLIC and PLC routing resources.
Programmable Function Unit
The PFUs are used for logic. Each PFU has 50 external
inputs and 18 outputs an d c an operate in several
modes. The fun ctionality of the inputs and out put s
depends on t he operating mode.
The PFU uses 36 data input lines for the LUT s, eight
data input lines for the latches/FFs, five control inputs
(ASWE, C LK, CE, LSR, SE L), and a carry input (C IN)
for fast arit hm etic functio ns and general-purpose data
input for the ninth FF. There are eight combinatorial data
outputs (one from each LUT ), eight latched /r egis t ered
outputs (one from each latch/FF) , a carry-out (COUT),
and a registered carry-out (REGCOUT) that comes from
the ninth F F. The carry-out signals are us ed princ ipally
f or fast arithmetic functions.
Figure 2 an d F igure 3 show high-level and detailed
views of the ports in th e PF U, respectively. The eig ht
sets of LUT inputs are labeled as K0 through K7 with
each of the four inputs to each LUT having a suffix of
_x, where x is a numb er f rom 0 t o 3. T here are four F5
inputs labeled A throug h D. These inputs are us ed for a
fifth LUT inpu t for 5-input LUTs or as a sele cto r for multi-
plexing two 4-input LUTs. The eight direct data inputs to
the latches/ FFs are labeled as DIN[ 7:0]. Registere d LUT
outputs are s hown a s Q [7:0], and comb inat orial LU T
outputs are labeled as F[7:0].
The PFU implements combinatorial logic in the LUTs
and sequential logic in the latches/FFs. The LUTs are
static random access memory (SRAM) and can be used
for read/write or rea d-only memory.
Each latc h/ F F can accept data f rom it s as so c iat ed LUT.
Alternativ ely, the latches/FFs can accept direct data
from DIN[7: 0] , elim inating the LU T delay if no combina-
torial fu nction is needed. Additionally, the CIN input can
be used as a direct data source for the ninth FF. The
LUT outputs c an b ypass the latch es/FFs , which reduces
the delay out of the PFU. It is possible to use the LUTs
and latches/FFs more or less independently, allowing,
for instance, a comparator function in the LUTs simulta-
neously w it h a s hif t re gis t er in the FFs.
5-5752(F)
Figure 2. PFU Ports
The PFU can be configured to operate in four modes:
logic mode, half-logic mode, r ipple mode, and memory
(RAM/ROM) mode. In addition, ripple mode has four
submodes and RAM mode can be used in either a
single- or dual-port mem ory fas hion. These su bm odes
of operation are discussed in the following sections.
5-5752(F)
F5D
K7
_0
K7
_1
K7
_2
K7
_3
K6
_0
K6
_1
K6
_2
K6
_3
K5
_0
K5
_1
K5
_2
K5
_3
K4
_0
K4
_1
K4
_2
K4
_3
F5C
DIN7
DIN6
DIN5
DIN4
DIN3
DIN2
DIN1
DIN0
CIN
F5B
K3
_0
K3
_1
K3
_2
K3
_3
K2
_0
K2
_1
K2
_2
K2
_3
K1
_0
K1
_1
K1
_2
K1
_3
K0
_0
K0
_1
K0
_2
K0
_3
F5A
LSR
CLK
CE
SEL
ASWE
FUNCTION UNIT
(PFU)
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
COUT
REGCOUT
F7
F6
F5
F4
F3
F2
F1
F0
12 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
5-5743(F)
Note: All multiplexers without select inputs are configuration selector multiplexers.
Figure 3. Simplified PFU Diagram
SEL
CIN
D
CE
CK
S/R
FF8 REGCOUT
COUT
1
ASWE
LSR
K7_3
K6_0
K6_1
K6_2
K6_3
K5_0
K5_1
K5_2
F5D
K7_0
K7_1
K7_2
K5_3
K4_0
K4_1
K4_2
K4_3
F5C
CLK
A
B
C
D
A
B
C
D
A
B
C
D
K4
K5
K6
K7 DIN7
DIN6
DIN5
DIN4
REG5
D0
D1
CE
CK
S/R
DSEL
Q5
F5
REG6
D0
D1
CE
CK
S/R
DSEL
Q6
F6
REG7
D0
D1
CE
CK
S/R
DSEL
Q7
F7
REG4
D0
D1
CE
CK
S/R
DSEL
Q4
F4
A
B
C
D
F5MODE45
K3_3
K2_0
K2_1
K2_2
K2_3
K1_0
K1_1
K1_2
F5B
K3_0
K3_1
K3_2
K1_3
K0_0
K0_1
K0_2
K0_3
F5A
A
B
C
D
A
B
C
D
A
B
C
D
K0
K1
K2
K3 DIN3
DIN2
DIN1
DIN0
REG1
D0
D1
CE
CK
S/R
DSEL
Q1
F1
REG2
D0
D1
CE
CK
S/R
DSEL
Q2
F2
REG3
D0
D1
CE
CK
S/R
DSEL
Q3
F3
REG0
D0
D1
CE
CK
S/R
DSEL
Q0
F0
A
B
C
D
F5MODE01
F5MODE67
F5MODE23
0
0
0
0
0
0
0
0
0
0
0
0
CE
0
0
0
1
1
1
0
0
0
0
1
0
1
0
1
0
1
0
Lucent Technologies Inc. 13
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Look-Up Table Operating Modes
The operating mode affects the functionality of the PFU input and output ports and internal PFU routing. For exam-
ple, in some operating modes, the DIN[7:0] inputs are direct data inputs to the PFU latches/FFs. In memory mode,
the same DIN[7:0] inputs are used as a 4-bit write data input bus and a 4-bit write address input bus into LUT
memory.
Table 3 lists the basic operating modes of the LUT. Figure 4—Figure 10 show bloc k diagrams of the LUT operating
modes. The accompanying descriptions demonstrate each mode’s use for generating logic.
PFU Control In
p
uts
Each PFU has five routable control inputs and an active-low, asynchronous global set/reset (GSRN) signal that
affects all latches and FFs in the device. The five control inputs are CLK, LSR, CE, ASWE, and SEL, and their
functionality for each logic mode of the PFU (discussed subsequently) is shown in Table 4. The clock signal to the
PFU is CLK, CE stands for clock enable, which is its primary function. LSR is the local set/reset signal that can be
configured as synchronous or asynchronous. The selection of set or reset is made for each latch/FF and is not a
function of the signal itself . ASWE stands f or add/subtract/write enable , which are its functions, along with being an
optional clock enable, and SEL is used to dynamically select between direct PFU input and LUT output data as the
input to the latches/FFs.
All of the control signals can be disabled and/or inverted via the configuration logic. A disabled clock enable indi-
cates that the cloc k is always enabled. A disabled LSR indicates that the latch/FF never sets/resets (except from
GSRN). A disabled SEL input indicates that DIN[7:0] PFU inputs are routed to the latches/FFs. F or logic and ripple
modes of the PFU , the LSR, CE, and ASWE (as a clock enab le) inputs can be disabled individually for each nibble
(latch/FF[3:0], latch/FF[7:4]) and for the ninth FF.
Table 3. Look-Up Table Operating Modes
Mode Function
Logic 4- and 5-input LUTs; softwired LUTs; latches/FFs with direct input or LUT input; CIN as direct input to
ninth FF or as pass through to COUT.
Half Logic/
Half Ripple Upper four LUTs and latches/FFs in logic mode; low er four LUTs and latches/FFs in ripple mode; CIN
and ninth FF for logic or ripple functions.
Ripple All LUTs combined to perform ripple-through data functions. Eight LUT registers availab le for direct-in
use or to register ripple output. Ninth FF dedicated to ripple out, if used. The submodes of ripple mode
are adder/subtractor, counter, multiplier, and comparator.
Memory All LUTs and latches/FFs used to create a 32 x 4 synchronous dual-port RAM. Can be used as single-
port or as ROM.
14 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Table 4. Control Input Functionality
Mode CLK LSR CE ASWE SEL
Logic CLK to all latches/
FFs LSR to all latches/
FFs, enabled per nib-
ble and for ninth FF
CE to all la tc hes /FF s ,
selectable per nibble
and for ninth FF
CE to all latches/FFs,
selectable per nibble
and for ninth FF
Select between LUT
input and direct input
for eight latches/FFs
Half Logic /
Half Ripple CLK to all latches/
FFs LSR to all latches/FF,
enabled per nibble
and for ninth FF
CE to all la tc hes/FFs,
selectable per nibble
and for ninth FF
Ripple logic control
input Select between LUT
input and direct input
for eight latches/FFs
Ripple CLK to all latches/
FFs LSR to all latches/
FFs, enabled per nib-
ble and for ninth FF
CE to all la tc hes /FF s ,
selectable per nibble
and for ninth FF
Ripple logic control
input Select between LUT
input and direct input
for eight latches/FFs
Memory
(RAM) CLK to RAM Port enable 2 Port enable 1 Write enable Not used
Memory
(ROM) Optional for sync.
outputs Not used Not used Not used Not used
Lo
g
ic Mode
The PFU diagram of Figure 3 represents the logic
mode of operation. In logic mode, the eight LUTs are
used individually or in fle xible groups to implement user
logic functions. The latches/FFs may be used in con-
junction with the LUTs or separately with the direct
PFU data inputs. There are three basic submodes of
LUT operation in PFU logic mode: F4 mode, F5 mode,
and softwired LUT (SWL) mode. Combinations of these
submodes are possible in each PFU.
F4 mode, shown simplified in Figure 4, illustrates the
uses of the basic 4-input LUTs in the PFU. The output
of an F4 LUT can be passed out of the PFU, captured
at the LUTs associated latch/FF, or multiplex ed with the
adjacent F4 LUT output using one of the F5[A:D] inputs
to the PFU. Only adjacent LUT pairs (K0 and K1, K2
and K3, K4 and K5, K6 and K7) can be multiplexed, and
the output alwa ys goes to the e v en-numbered output of
the pair.
The F5 submode of the LUT operation, shown simpli-
fied in Figure 4, indicates the use of 5-input LUTs to
implement logic. 5-input LUTs are created from two
4-input LUTs and a multiplexer. The F5 LUT is the
same as the multiplexing of two F4 LUTs described
previously with the constraint that the inputs to the F4
LUTs be the same. The F5[A:D] input is then used as
the fifth LUT input. The equations for the two F4 LUTs
will differ by the assumed value for the F5[A:D] input,
one F4 LUT assuming that the F5[A:D] input is zero,
and the other assuming it is a one. The selection of the
appropriate F4 LUT output in the F5 MUX by the
F5[A:D] signal creates a 5-input LUT. Any combination
of F4 and F5 LUTs is allowed per PFU using the eight
16-bit LUTs. Examples are eight F4 LUTs, four F5
LUTs, and a combination of four F4 plus two F5 LUTs. 5-5970(F)
Figure 4. Simplified F4 and F5 Logic Modes
K7F7 K7
F6
K6
F5D
K6F6
K5F5 K5
F4
K4
F5C
K4F4
K3F3
K3
F2
K2
F5B
K2F2
K1F1 K1
F0
K0
F5A
K0F0
K7/K6F6
K5/K4F4
K3/K2F2
K1/K0F0
F5 MODE
MULTIPLEXED F4 MODEF4 MOD E
Lucent Technologies Inc. 15
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Softwired LUT submode uses F4 and F5 LUTs and internal PFU feedback routing to generate complex logic func-
tions up to three LUT-levels deep. Figure 3 shows multiple xers between the KZ[3:0] inputs to the PFU and the
LUTs. These multiple x ers can be independently configured to route certain LUT outputs to the input of other LUTs.
In this manner, very complex logic functions, some of up to 21 inputs, can be implemented in a single PFU at
greatly enhanced speeds.
Figure 5 shows several softwired LUT topologies. In this figure, each circle represents either an F4 or F5 LUT. It is
important to note that an LUT output that is fed back for softwired use is still available to be registered or output
from the PFU. This means, for instance, that a logic equation that is needed by itself and as a term in a larger
equation need only be generated once and PLC routing resources will not be required to use it in the larger equa-
tion.
Figure 5. Softwired LUT Topology Examples
5-5753(F)
F4
KEY:
F54-INPUT LUT 5-INPUT LUT
5-5754(F)
F4
F4
F4
F4
F4
F4
F4
F4
FOUR 7-INPUT FUNCTIONS IN ONE PFU
F5
F5
F5
F5
TWO 9-INPUT FUNCTIONS IN ONE PFU
F5
F5
F5
F5
ONE 17-INPUT FUNCTION IN ONE PFU
F5
F5
F4
ONE 21-INPUT FUNCTION IN ONE PFU
F4 F4 F4
F4
F4
F4
F4
TWO OF FOUR 10-INPUT FUNCTIONS IN ONE PFU
F4
F4
F4
F4
3
ONE OF TWO 12-INPUT FUNCTIONS IN ONE PFU
1616 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Half-Lo
g
ic Mode
Series 3 FPGAs are based upon a twin-quad architec-
ture in the PFUs. The byte-wide nature (eight LUTs,
eight latches/FFs) may just as easily be viewed as two
nibbles (two sets of four LUTs, four latches/FFs). The
two nibbles of the PFU are organized so that any nib-
ble-wide feature (excluding some softwired LUT topolo-
gies) can be swapped with any other nibble-wide
feature in another PFU. This provides for very flexible
use of logic and for extremely flexible routing. The half-
logic mode of the PFU takes adv antage of the twin-
quad architecture and allows half of a PFU, K[7:4] and
associated latches/FFs, to be used in logic mode while
the other half of the PFU, K[3:0] and associated latches/
FFs, is used in ripple mode. In half-logic mode, the
ninth FF may be used as a general-purpose FF or as a
register in the ripple mode carry chain.
Ri
pp
le Mode
The PFU LUTs can be combined to do byte-wide ripple
functions with high-speed carry logic. Each LUT has a
dedicated carry-out net to route the carry to/from any
adjacent LUT. Using the internal carry circuits, fast
arithmetic, counter, and comparison functions can be
implemented in one PFU. Similarly, each PFU has
carry-in (CIN, FCIN) and carry-out (COUT, FCOUT)
ports for fast-carry routing between adjacent PFUs.
The ripple mode is generally used in oper ations on two
data buses. A single PFU can support an 8-bit ripple
function. Data buses of 4 bits and less can use the
nibble-wide ripple chain that is available in half-logic
mode. This nibble-wide ripple chain is also useful for
longer ripple chains where the length modulo 8 is four
or less. For example, a 12-bit adder (12 modulo 8 = 4)
can be implemented in one PFU in ripple mode (8 bits)
and one PFU in half-logic mode (4 bits), freeing half of
a PFU for general logic mode functions.
Each LUT has two operands and a ripple (generally
carry) input, and provides a result and ripple (generally
carry) output. A single bit is rippled from the previous
LUT and is used as input into the current LUT. F or LUT
K0, the ripple input is from the PFU CIN or FCIN port.
The CIN/FCIN data can come from either the f ast-carry
routing (FCIN) or the PFU input (CIN), or it can be tied
to logic 1 or logic 0.
In the following discussions, the notations LUT K7/K3
and F[7:0]/F[3:0] are used to denote the LUT that pro-
vides the carry-out and the data outputs for full PFU
ripple operation (K7, F[7:0]) and half-logic ripple
operation (K3, F[3:0]), respectively. The ripple mode
diagram in Figure 6 shows full PFU ripple operation,
with half-logic ripple connections shown as dashed
lines.
The result output and ripple output are calculated by
using generate/propagate circuitry. In ripple mode, the
two operands are input into KZ[1] and KZ[0] of each
LUT. The result bits, one per LUT, are F[7:0]/F[3:0] (see
Figure 6). The ripple output from LUT K7/K3 can be
routed on dedicated carry circuitry into any of four adja-
cent PLCs, and it can be placed on the PFU COUT/
FCOUT outputs. This allows the PLCs to be cascaded
in the ripple mode so that nibb le-wide ripple functions
can be expanded easily to any length.
Result outputs and the carry-out may optionally be reg-
istered within the PFU. The capability to register the
ripple results, including the carry output, provides for
improved counter performance and simplified pipelin-
ing in arithmetic functions.
Figure 6. Ripple Mode
5-5755(F)
F7
K7[1]
K7[0] K7DQ
C
C
DQ
Q7
REGCOUT
COUT
F6
K6[1]
K6[0] K6DQQ6
F4
K4[1]
K4[0] K4DQQ4
F3
K3[1]
K3[0] K3DQQ3
F2
K2[1]
K2[0] K2DQQ2
F1
K1[1]
K1[0] K1DQQ1
F5
K5[1]
K5[0] K5DQQ5
F0
K0[1]
K0[0] K0DQQ0
CIN/FCIN
FCOUT
Lucent Technologies Inc. 17
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
The ripple mode can be used in one of f our submodes.
The first of these is adder-subtractor submode. In
this submode, each LUT generates three separate out-
puts. One of the three outputs selects whether the
carry-in is to be propagated to the carry-out of the cur-
rent LUT or if the carry-out needs to be generated. If
the carry-out needs to be generated, this is provided b y
the second LUT output. The result of this selection is
placed on the carry-out signal, which is connected to
the ne xt LUT carry-in or the COUT/FCOUT signal, if it
is the last LUT (K7/K3). Both of these outputs can be
any equation created from KZ[1] and KZ[0], but in this
case, they have been set to the propagate and gener-
ate functions.
The third LUT output creates the result bit f or each LUT
output connected to F[7:0]/F[3:0]. If an adder/subtrac-
tor is needed, the control signal to select addition or
subtraction is input on ASWE, with a logic 0 indicating
subtraction and a logic 1 indicating addition. The result
bit is created in one-half of the LUT from a single bit
from each input bus KZ[1:0], along with the ripple input
bit.
The second submode is the counter submode (see
Figure 7). The present count, which may be initialized
via the PFU DIN inputs to the latches/FFs, is supplied
to input KZ[0], and then output F[7:0]/F[3:0] will either
be incremented by one f or an up counter or decre-
mented by one for a down counter. If an up/down
counter is needed, the control signal to select the direc-
tion (up or down) is input on ASWE with a logic 1 indi-
cating an up counter and a logic 0 indicating a down
counter. Generally, the latches/FFs in the same PFU
are used to hold the present count value.
Figure 7. Counter Submode
5-5756(F)
F7
K7[0] K7DQ
C
C
DQ
Q7
REGCOUT
COUT
F6
K6[0] K6DQQ6
F4
K4[0] K4DQQ4
F3
K3[0] K3DQQ3
F2
K2[0] K2DQQ2
F1
K1[0] K1DQQ1
F5
K5[0] K5DQQ5
F0
K0[0] K0DQQ0
CIN/FCIN
FCOUT
1818 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
In the third submode, multiplier submode, a single
PFU can affect an 8 x 1 bit (4 x 1 for half-ripple mode)
multiply and sum with a partial product (see Figure 8).
The multiplier bit is input at ASWE, and the multiplicand
bits are input at KZ[1], where K7[1] is the most signifi-
cant bit (MSB). KZ[0] contains the partial product (or
other input to be summed) from a previous stage. If
ASWE is logical 1, the multiplicand is added to the par-
tial product. If ASWE is logical 0, 0 is added to the par-
tial product, which is the same as passing the partial
product. CIN/FCIN can bring the carry-in from the less
significant PFUs if the multiplicand is wider than 8 bits,
and COUT/FCOUT holds any carry-out from the multi-
plication, which may then be used as part of the prod-
uct or routed to another PFU in multiplier mode for
multiplic and wid th expansion.
Ripple mode’s fourth submode f eatures equality
comparators. The functions that are explicitly av ailable
are A > B, A ≠ B, and A < B, where the value for A is
input on KZ[0], and the value for B is input on KZ[1]. A
value of 1 on the carry-out signals valid argument. For
example, a carry-out equal to 1 in AB submode indi-
cates that the v alue on KZ[0] is greater than or equal to
the v alue on KZ[1]. Con versely, the functions A < B, A +
B , and A > B are available using the same functions b ut
with a 0 output expected. F or example, A > B with a 0
output indicates A < B. Table 5 shows each function
and the output expected.
If larger than 8 bits, the carry-out signal can be cas-
caded using fast-carry logic to the carry-in of any adja-
cent PFU. The use of this submode could be shown
using Figure 6, except that the CIN/FCIN input for the
least significant PFU is controlled via configuration.
Key: C = configuration data.
Figure 8. Multiplier Submode
Table 5. Ripple Mode Equality Comparator
Functions and Outputs
Equality
Function
ORCA
Foundry
Submode True , if
Carry-Out Is:
A > BA > B1
A < BA < B1
A ≠ BA
≠ B1
A < B A > B0
A > B A < B0
A = B A ≠ B0
5-5757(F)
K7[1]
K7[0] +DQ
C
C
DQ
1
00
K7
ASWE
K4[1]
K4[0] +DQ
1
00
K4
K3[1]
K3[0] +DQ
1
00
K3
K2[1]
K2[0] +DQ
1
00
K2
K1[1]
K1[0] +DQ
1
00
K1
K6[1]
K6[0] +DQ
1
00
K6
K5[1]
K5[0] +DQ
1
00
K5
K0[1]
K0[0] +DQ
1
00
K0
F7
Q7
REGCOUT
COUT
F6
Q6
F4
Q4
F3
Q3
F2
Q2
F1
Q1
F5
Q5
F0
Q0
Lucent Technologies Inc. 19
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Memor
y
Mode
The Series 3 PFU can be used to implement a 32 x 4 (128-bit) synchronous, dual-port random access memory
(RAM). A block diagram of a PFU in memory mode is shown in Figure 9. This RAM can also be configured to work
as a single-port memory and because initial values can be loaded into the RAM during configuration, it can also be
used as a read-only memory (ROM).
Figure 9. Memory Mode
The PFU memory mode uses all LUTs and latches/FFs including the ninth FF in its implementation as shown in
Figure 9. The read address is input at the KZ[3:0] and F5[A:D] inputs where KZ[0] is the LSB and F5[A:D] is the
MSB, and the write address is input on CIN (MSB) and DIN[7, 5, 3, 1], with DIN[1] being the LSB. Write data is
input on DIN[6, 4, 2, 0], where DIN[6] is the MSB , and read data is available combinatorially on F[6, 4, 2, 0] and
registered on Q[6, 4, 2, 0] with F[6] and Q[6] being the MSB. The write enable signal is input at ASWE, and two
write port enab les are input on CE and LSR. The PFU CLK signal is used to synchronously write the data. The
polarities of the clock, write enable, and port enables are all programmable. Write-port enables may be disabled if
they are not to be used.
5-5969(F)
Q6
Q4
Q2
Q0
D5
Q
CIN(WA4)
KZ[3:0] 4
F5[A:D]
D Q
DIN7(WA3)
D Q
DIN5(WA2)
D Q
DIN3(WA1)
D Q
DIN1(WA0)
D Q
DIN6(WD3)
D Q
DIN4(WD2)
D Q
DIN2(WD1)
D Q
DIN0(WD0)
D Q
ASWE(WREN) EN
S/R
CE(WPE1)
LSR(WPE2)
CLK
4WRITE
WRITE
READ
READ 4
F6
F4
F2
F0
D Q
D Q
D Q
D Q
WRITE
RAM CLOCK
ADDRESS[4:0]
ADDRESS[4:0]
DATA[3:0]
DATA[3:0]
ENABLE
2020 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Data is written to the write data, write address, and
write enable registers on the active edge of the clock,
but data is not written into the RAM until the next clock
edge one-half cycle later. The read port is actually
asynchronous, providing the user with read data very
quickly after setting the read address, but timing is also
provided so that the read port may be treated as fully
synchronous for write then read applications. If the
read and write address lines are tied together (main-
taining MSB to MSB, etc.), then the dual-port RAM
operates as a synchronous single-port RAM. If the
write enable is disabled, and an initial memory contents
is pro vided at configuration time, the memory acts as a
ROM (the write data and write address ports and write
port enables are not used).
Wider memories can be created by operating two or
more memory mode PFUs in parallel, all with the same
address and control signals, but each with a different
nibble of data. To increase memory word depth above
32, two or more PLCs can be used. Figure 10 shows a
128 x 8 dual-port RAM that is implemented in eight
PLCs. This figure demonstrates data path width expan-
sion by placing two memories in parallel to achieve an
8-bit data path. Depth expansion is applied to achieve
128 words deep using the 32-word deep PFU memo-
ries . In addition to the PFU in each PLC, the SLIC
(described in the next section) in each PLC is used for
read address decodes and 3-state drivers. The 128 x 8
RAM shown could be made to operate as a single-port
RAM by tying (bit-for-bit) the read and write addresses.
To achieve depth expansion, one or two of the write
address bits (generally the MSBs) are routed to the
write port enab les as in Figure 10. For 2 bits, the bits
select which 32-word bank of RAM of the f our av ailable
from a decode of two WPE inputs is to be written. Simi-
larly, 2 bits of the read address are decoded in the
SLIC and are used to control the 3-state buffers
through which the read data passes. The write data
bus is common, with separate nibbles for width expan-
sion, across all PLCs, and the read data bus is com-
mon (again, with separate nibbles) to all PLCs at the
output of the 3-state buffers.
Figure 10 also shows a new optional capability to pro-
vide a read enable for RAMs/ROMs in Series 3 using
the SLIC cell. The read enable will 3-state the read
data bus when inactive, allowing the write data and
read data buses to be tied together if desired.
Figure 10. Memory Mode Expansion Example—128 x 8 RAM
5-5749(F)
RD[7:0]
WE
WA[6:0]
RA[6:0]
CLK
WA RA
WPE0
WPE1
WE
WD[7:4]
5 5
4PLC
8
WD[7:0]
8
7
7
WA RA
WPE0
WPE1
WE
RD[3:0]
WD[3:0]
5 5
4PLC
RD[7:4]
WA RA
WPE0
WPE1
WE
WD[7:4]
5 5
4PLC
WA RA
WPE0
WPE1
WE
RD[3:0]
WD[3:0]
5 5
4PLC
RD[7:4]
RE
4 4 4 4
PFU PFU PFU PFU
SLIC
SLIC
SLIC SLIC
Lucent Technologies Inc. 21
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Supplemental Logic and Interc onnect Cell
(SLIC)
Each PLC contains a supplemental logic and intercon-
nect cell (SLIC) embedded within the PLC routing, out-
side of the PFU. As its name indicates, the SLIC
performs both logic and interconnect (routing) func-
ti ons . Its mai n feat ures ar e 3-s t atab l e , b id irec tio nal b uf f-
ers, and a
PAL
-like decoder capability. Figure 11 shows
a diagram of a SLIC with all of its features shown. All
modes of the SLIC are not available at one time.
Each SLIC contains ten bidirectional (BIDI) buffers,
each buff er capable of driving left and/or right out of the
SLIC. These BIDI buffers are twin-quad in nature and
are segregated into two groups of four (nibbles) and a
third group of two for control. Each of these groups of
BIDIs can drive from the left (BLI[9:0]) to the right
(BRO[9:0]), the right (BRI[9:0]) to the left (BLO[9:0]), or
from the central input (I[9:0]) to the left and/or right.
This centr al input comes directly from the PFU outputs
(O[9:0]). Each of the BIDIs in the nibble-wide groups
also has a 3-state buffer capability, but not the third
group.
There is one 3-state control (TRI) for each SLIC, with
the capability to invert or disable the 3-state control for
each group of four BIDIs. Separate 3-state control for
each nibble-wide group is achievab le by using the
SLIC’s decoder (DEC) output, driven by the group of
two BIDIs, to control the 3-state of one BIDI nibble
while using the TRI signal to control the 3-state of the
other BIDI nibble. Figure 12 and Figure 13 show the
SLIC in buff er mode with available 3-state control from
the TRI and DEC signals. If the entire SLIC is acting in
a buffer capacity, the DEC output may be used to gen-
erate a constant logic 1 (VHI) or logic 0 (VLO) signal f or
general use.
The SLIC may also be used to generate
PAL
-like AND-
OR with optional INVERT (AOI) functions or a decoder
of up to 10 bits. Each group of buffers can feed into an
AND gate (4-input AND for the nibble groups and 2-
input AND for the other two buffers). These AND gates
then feed into a 3-input gate that can be configured as
either an AND gate or an OR gate. The output of the 3-
input gate is invertible and is output at the DEC output
of the SLIC. Figure 16 shows the SLIC in full decoder
mode.
The functionality of the SLIC is parsed by the two
nibble-wide groups and the 2-bit buffer group. Each of
these groups may operate independently as BIDI buff-
ers (with or without 3-state capability for the nibble-
wide groups) or as a
PAL
/decoder.
As discussed in the memory mode section, if the SLIC
is placed into one of the modes where it contains both
buffers and a decode or AOI function (e.g.,
BUF_BUF_DEC mode), the DEC output can be gated
with the 3-state input signal. This allows up to a 6-input
decode (e.g., BUF_DEC_DEC mode) plus the 3-state
input to control the enable/disable of up to four buffers
per SLIC. Figure 12—Figure 16 show several configu-
rations of the SLIC , while Table 6 shows all of the possi-
ble modes.
Table 6. SLIC Modes
Mode
#Mode BUF
[3:0] BUF
[7:4] BUF
[9:8]
1 BUFFER Buffer Buffer Buffer
2 BUF_BUF_DEC Buffer Buffer Decoder
3 BUF_DEC_BUF Buffer Decoder Buffer
4 BUF_DEC_DEC Buffer Decoder Decoder
5 DEC_BUF_BUF Decoder Buffer Buffer
6 DEC_BUF_DEC Decoder Buffer Decoder
7 DEC_DEC_BUF Decoder Decoder Buffer
8 DECODER Decoder Decoder Decoder
2222 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Figure 11. SLIC All Modes Diagram
Figure 12. Buffer Mode
5-5744(F)
BRI9
I9
BLI9
BRI8
I8
BLI8
BRI7
I7
BLI7
BRI6
I6
BLI6
BRI5
I5
BLI5
BRI4
I4
BLI4
BRI3
I3
BLI3
BRI2
I2
BLI2
BRI1
I1
BLI1
BRI0
I0
BLI0
BL09
BR09
BL08
BR08
BL07
BR07
BL06
BR06
BL05
BR05
BL04
BR04
BL03
BR03
BL02
BR02
BL01
BR01
BL00
BR00
DEC
DEC
0/1
0/1
TRI
0/1
0/1
HIGH Z WHEN LOW
5-5745(F)
BRI9
I9
BLI9
BRI8
I8
BLI8
BRI7
I7
BLI7
BRI6
I6
BLI6
BRI5
I5
BLI5
BRI4
I4
BLI4
BRI3
I3
BLI3
BRI2
I2
BLI2
BRI1
I1
BLI1
BRI0
I0
BLI0
BL09
BR09
BL08
BR08
BL07
BR07
BL06
BR06
BL05
BR05
BL04
BR04
BL03
BR03
BL02
BR02
BL01
BR01
BL00
BR00
TRI
0/1
0/1
1
0DEC
THIS CAN BE USED
A VHI OR VLO
HIGH Z WHEN LOW
TO GENERATE
Lucent Technologies Inc. 23
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Figure 13. Buffer -Buffer-Decoder Mode Figure 14. Buffer-Decoder-Buffer Mode
5-5746(F)
BRI9
BLI9
BRI8
BLI8
BRI7
I7
BLI7
BRI6
I6
BLI6
BRI5
I5
BLI5
BRI4
I4
BLI4
BRI3
I3
BLI3
BRI2
I2
BLI2
BRI1
I1
BLI1
BRI0
I0
BLI0
BL07
BR07
BL06
BR06
BL05
BR05
BL04
BR04
BL03
BR03
BL02
BR02
BL01
BR01
BL00
BR00
TRI DEC
1
1
1
1
HIGH Z
WHEN LOW
HIGH Z
WHEN LOW
5-5747(F)
BRI7
BLI7
BRI6
BLI6
BRI5
BLI5
BRI4
BLI4
BRI3
I3
BLI3
BRI2
I2
BLI2
BRI1
I1
BLI1
BRI0
I0
BLI0
BL03
BR03
BL02
BR02
BL01
BR01
BL00
BR00
TRI
DEC
BRI9
I9
BLI9
BRI8
I8
BLI8
BL09
BR09
BL08
BR08
1
1
HIGH Z WHEN LOW
2424 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Figure 15. Buffer-Decoder-Decoder Mode
Figure 16. Decoder Mode
5-5750(F)
BRI7
BLI7
BRI6
BLI6
BRI5
BLI5
BRI4
BLI4
BRI3
I3
BLI3
BRI2
I2
BLI2
BRI1
I1
BLI1
BRI0
I0
BLI0
BL03
BR03
BL02
BR02
BL01
BR01
BL00
BR00
TRI
DEC
BRI9
BLI9
BRI8
BLI8
1
1HIGH Z WHEN LOW
5-5748(F)
BRI7
BLI7
BRI6
BLI6
BRI5
BLI5
BRI4
BLI4
BRI3
BLI3
BRI2
BLI2
BRI1
BLI1
BRI0
BLI0
DEC
BRI9
BLI9
BRI8
BLI8
Lucent Technologies Inc. 25
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
PLC Latches/Flip-Flops
The eight general-p urpose latches/FFs in the PFU can
be used in a v ariety of configurations. In some cases,
the configura tion options apply to all eight latches/FFs in
the PFU and some apply to the latches/FFs on a nibble-
wide basis where the ninth FF is considered indepen-
dently. F or other options, each latch/FF is independently
programmable. In addition, the ninth FF can be used for
a variety of functions.
Table 7 summarizes these latch/FF options. The
latches/FFs can be configured as either positive- or
negative-level sensitive latches, or positive or negative
edge-triggered flip-flops (the ninth register can only be
FF). All latches/FFs in a given PFU share the same
clock, and the clock to these latches/FFs can be
inv erted. The input into each latch/FF is from either the
corresponding LUT output (F[7:0]) or the direct data
input (DIN[7:0]). The latch/FF input can also be tied to
logic 1 or to logic 0, which is the default.
* Not available for FF[8].
The eight latches/FFs in a PFU share th e clock (CLK)
and options for clock enable (CE), local set/reset (LSR),
and front-end data selec t (SEL) inputs. When C E is dis -
abled, each latch/FF retains its previous value when
clocked. The cl ock enable, LSR, and SEL inputs can be
inverted to be ac t ive-low.
The set/reset operation of the latch/FF is controlle d by
two parameters: res et mode and s et /r es et value. When
the globa l se t/reset (GSRN) and local set/reset (LSR)
signals ar e not asserted, the latch /FF operates n ormally.
The reset mode is used to select a synchronous or
asynchr onous LSR operat ion. If synchronous, LSR has
the option t o be enabled only if clock enable (CE or
ASWE) is ac t ive or for LSR to have priority over the
clock enable input, thereby setting/re se tting the FF inde-
pendent of the stat e of the clock enable. The clock
enable is supported on FFs, not latches. It is imple-
mented by using a 2-input multiplexer on the FF input,
with one input being the pre vious state of the FF and the
other inp ut being the new data applie d t o th e F F. The
select of th is 2-input multiplexer is clock enable (CE or
ASWE), w hic h selects eith er t he new data or the previ-
ous state. When t he clock enable is inactive, the F F out -
put does not change wh en t he clock edge arr ives.
Table 7. Configuration RAM Controlled Latch/
Flip-Flop Operation
Function Options
Common to All La tches/FFs in PFU
LSR Ope ratio n Asynch ronous or synchronous
Clock Polar ity Noninverted or inverted
Front-end Select* Direct (DIN[7:0]) or from LUT (F[7:0])
LSR Prior it y Either LS R or C E has prio rity
Latch/FF M ode Latch or fl ip-f lop
Enable GSRN GSRN enabled or has no effect on
PFU latches/FFs
Set Individuall y in Each Latch/FF in PFU
Set/Reset Mode Set or reset
By Group (Latch/FF[3:0], Latch/FF[7:4], and FF[8])
Clock Enable CE or ASW E or none
LSR Cont rol LSR or none
2626 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
The GSRN signal is only asynchronous, and it sets/
resets all latches/FFs in the FPGA based upon the set/
reset configuration bit for each latch/FF. The set/reset
value determines whether GSRN and LSR are set or
reset inputs. The set/reset v alue is independent for
each latch/FF. A new option is available to disable the
GSRN function per PFU after initial device configura-
tion.
The latch/FF can be configured to have a data front-
end select. Two data inputs are possible in the front-
end select mode, with the SEL signal used to select
which data input is used. The data input into each
latch/FF is from the output of its associated LUT, F[7:0],
or direct from DIN[7:0], bypassing the LUT. In the front-
end data select mode, both signals are a vailable to the
latches/FFs.
If either or both of these inputs is unused or is unavail-
able, the latch/FF data input can be tied to a logic 0 or
logic 1 instead (the default is logic 0).
The latches/FFs can be configured in three basic
modes:
1. Local synchronous set/reset: the input into the
PFU’s LSR port is used to synchronously set or
reset each latch/FF.
2. Local asynchronous set/reset: the input into LSR
asynchronously sets or resets each latch/FF.
3. Latch/FF with front-end select, LSR either synchro-
nous or asynchronous: the data select signal
selects the input into the latches/FFs between the
LUT output and direct data in.
For all three modes, each latch/FF can be indepen-
dently programmed as either set or reset. Figure 17
provides the logic functionality of the front-end select,
global set/reset, and local set/reset operations.
The ninth PFU FF, which is generally associated with
registering the carry-out signal in ripple mode func-
tions, can be used as a general-purpose FF. It is only
an FF and is not capab le of being configured as a latch.
Because the ninth FF is not associated with an LUT,
there is no front-end data select. The data input to the
ninth FF is limited to the CIN input, logic 1, logic 0, or
the carry-out in ripple and half-logic modes.
Ke
y
: C = confi
g
uration data. Fi
g
ure 17. Latch/FF Set/Reset Confi
g
urations
DIN
LOGIC 0
LOGIC 1
F
CE
D
s_set
s_reset
CLK
SET RESET
Q
LSR
GSRN
CD
CE/ASWE
D
CLK
SET RESET
LSR
CD
CE
CE/ASWE
D
CLK
SET RESET
CD
CE
CE/ASWE
DIN
SEL
GSRN
DIN
LOGIC 0
LOGIC 1
FDIN
LOGIC 0
LOGIC 1
F
LSR
GSRN
Q Q
Lucent Technologies Inc. 27
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
PLC Routing Resources
Generally, the
ORCA
Foundry
Development System is
used to automatically route interconnections . Interac-
tive routing with the
ORCA
Foundry design editor
(EPIC) is also available for design optimization. To use
EPIC for interactive layout, an understanding of the
routing resources is needed and is provided in this sec-
tion.
The routing resources consist of s witching circuitry and
metal interconnect segments. Generally, the metal lines
which carry the signals are designated as routing seg-
ments. The switching circuitry connects the routing
segments, prov iding one or more of three basic func-
tions: signal switching, amplification, and isolation. A
net running from a PFU or PIC output (source) to a
PLC or PIC input (destination) consists of one or more
routing segments, connected by switching circuitry
called configurable interconnect points (CIPs).
The f ollowing sections discuss PLC, PIC , and interquad
routing resources. This secti on disc us se s the PLC
s witching circuitry, intra-PLC routing, inter-PLC routing,
and clock distribution.
Confi
g
urable Interconnect Points
The process of connecting routing segments uses
three basic types of s witching circuits: two types of con-
figurable interconnect points (CIPs) and bidirectional
buffers (BIDIs). The basic element in CIPs is one or
more pass transistors, each controlled by a configura-
tion RAM bit. The two types of CIPs are the mutually
e xclusive (or multiplex ed) CIP and the independent CIP.
A mutually exclusive set of CIPs contains two or more
CIPs, only one of which can be on at a time. An inde-
pendent CIP has no such restrictions and can be on
independent of the state of other CIPs. Figure 18
shows an example of both types of CIPs.
Ke
y
: C = confi
g
uration data. 5-5973(C)
Fi
g
ure 18. Confi
g
urable Interconnect Point
3-Statable Bidirectional Buffers
Bidirectional buffers, previously described in the SLIC
section of the programmable logic cell discussion, pro-
vide isolation as well as amplification f or signals routed
a long distance. Bidirectional buffers are also used to
route signals diagonally in the PLC (described later in
the subsection entitled Intra-PLC Routing), and BIDIs
can be used to indirectly route signals through the
switching routing (xSW) segments. Any n umber from
zero to ten BIDIs can be used in a given PLC.
MULTIPLEXED CIP
A
B
C
O
A
B
C
O
CD
INDEPENDENT CIP
A
BCD
BA
=
2
28 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
General Routing Structure
Routing resources in Series 3 FPGAs generally consist of routing segments in groups of ten, with varying lengths
and connectivity to logic and other routing resources. The v arying lengths of routing segments provides a hierarchy
of routing capability from chip-length routes to routes within a PLC. The hierarchical nature of the routing provides
the
ORCA
Foundry development tools with the necessary resources to route a design completely and to optimize
the routing for system speed while reducing the over all power required by the device.
Within each group of ten routing segments there is an equivalency of connectivity between pairs of segments.
These pairs are segments: [0, 4] and [1, 5] and [2, 6] and [3, 7] and [8, 9]. The equiv alency in connectivity ensures
that signals on either segment in a pair have the same capability to get to a given destination. This, in turn, allows
f or signal distribution from a source to v arying destinations without using special routing. It also provides for routing
flex ibility by ensuring that one segment position will not become so congested as to preclude routing a bus or group
of signals and allows easy connectivity from either of the twin quads in a source PFU to either of the twin quads in
any destination PFU.
Having ten segments in a group is significant in that it prov ides for routing a byte of data and two control signals or
parity. Due to the equivalent pairs of segments, this can also be viewed as routing two nibbles each with a control
signal. Figure 19 is an overview of the routing for a single PLC.
5-5766(F)
Fi
g
ure 19. Sin
g
le PLC View of Inter-PLC Route Se
g
ments
2 OF 5
LINE-BY-LINE
FINS PFU
OUTPUT
SLIC
SWITCHING
SUR[9:0]
BL[9:0]
vxL[9:0]
vx5[9:0]
vx1L[9:0]
SUL[9:0]
vx1R[9:0]
FC
LCK
VCK
vxH[9:0]
BL[9:0]
hxH[9:0]
hx1U[9:0]
hCK
FC
SLL[9:0]
hx1B[9:0]
hx5[9:0]
hxL[9:0]
BR[9:0]
SUL[9:0]
BL[9:0]FCSUL[9:0]
BR[9:0]
LCK
SLL[9:0]
FC
SLR[9:0]
5
2
5
2
5
2
KEY: CONFIGURABLE SIGNAL LINE BREAKS
Lucent Technologies Inc. 29
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Intra-PLC Routin
g
The function of the intra-PLC routing resources is to
connect the PFU’s input and output ports to the routing
resources used for entry to and exit from the PLC. This
routing provides PFU feedback, corner turning, or
switching from one type of routing resource to another.
Flexible In
p
ut Structure
(
FINS
)
The fle xible input switching structure (FINS) in each
PLC of the
ORCA
Series 3 provides for the flexibility of
a crossbar switch from the routing resources to the
PFU inputs while taking advantage of the routability of
shared inputs. Connectivity between the PLC routing
resources and the PFU inputs is provided in two
stages. The primary FINS switch has 50 inputs that
connect the PLC routing to the 35 inputs on the sec-
ondary switch. The outputs of the second switch con-
nect to the 50 PFU inputs. The switches are
implemented to provide connectivity for bused signals
and individual connections.
PFU Out
p
ut Switchin
g
The PFU outputs are switched onto PLC routing
resources via the PFU output multiplexer (OMUX). The
PFU output switching segments from the output multi-
plex er provide ten connections to the PLC routing out
of 18 possib le PFU outputs (F[7:0], Q[7:0], DOUT,
REGCOUT). These output switching segments con-
nect segment for segment to the SUR, SUL, SLR, and
SLL switching segments described below (e.g., O4
connects only to SUR4, not SUR5). The output switch-
ing segments also feed directly into the SLIC on a seg-
ment-by-segment basis. This connectivity is also
described below.
Switching Routing Segments (xSW)
There are four sets of switching routing segments in
each PLC . Each set consists of ten s witching elements:
SUL[9:0], SUR[9:0], SLL[9:0], and SLR[9:0], tradition-
ally labeled for the upper-left, upper-right, lower-left,
and lower-right sections of the PFUs, respectively. The
xSW routing segments connect to the PFU inputs and
outputs as well as the BIDI routing segments, to be
described later. They also connect to both the horizon-
tal and vertical x1 and x5 routing segments (inter-PLC
routing resources, described later) in their specific cor-
ner. xSW segments can be used for fast connections
between adjacent PLCs or PICs without requiring the
use of inter-PLC routing resources. This capability not
only increases signal speed on adjacent PLC routing,
but also reduces routing congestion on the principal
inter-PLC routing resources. The SLL and SUR seg-
ments combine to pro vide connectivity to the PLCs to
the left and right of the current PLC; the SLR and SUL
segments combine to provide connectivity to the PLCs
above and below the current PLC.
Fast routes on s witching segments to diagonally adja-
cent PLCs/PICs are possible using the BIDI routing
segments (discussed below) and the SLL and SLR
switching segments. The BR BIDI routing segments
combine with the SUL switching segments of the PLC
below and to the right of the current PLC to connect to
that PLC. The BL BIDI routing segments combine with
the SLL switching segments of the PLC above and to
the right of the current PLC to connect to that PLC.
These fast diagonal connections provide a great
amount of flexibility in routing congested areas of logic
and in shifting data on a per-PLC basis such as per-
forming implicit multiplications/divisions in routing
between functional logic elements.
Switching routing segments are also the chief means
by which signals are transferred between the inter-PLC
routing resources and the PFU. Each set of switching
segments has connectivity to the x1 routing segments,
and there is v arying connectivity to the x5, xH, and xL
inter-PLC routing segments. Detailed information on
switching segment/inter-PLC routing connectivity is
provided later in this section in the Inter-PLC Routing
Resources subsection.
3030 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
BIDI Routin
g
and SLIC Connectivit
y
The SLIC is connected to the rest of the PLC by the
bidirectional (BIDI) routing segments and the PFU out-
put switching segments coming from the PFU output
multiplexer. The BIDI routing segments (xBID) are
labeled as BL for BIDI-left and BR for BIDI-right. Each
set of BR and BL xBID segments is composed of ten
bidirectional lines (note that these lines are diagramed
as ten input lines to the SLIC and ten output lines from
the SLIC that can be used in a mutually exclusive fash-
ion). Because the SLIC is connected directly to the out-
puts of the PFU , it prov ides great fle xibility in routing via
the xBID segments. The PFU routing segments, O[9:0],
only connect to their respective line in the SLL, SUL,
SUR, and SLR switching segment groups. That is, O9
only connects to SLL9, SUL9, SUR9, and SLR9. The
BIDI lines provide the capability to connect to the other
member of the routing set. That means, for example,
that O9 can be routed to BR8 or BL8. This connectivity
can be used as a means to distribute or gather signals
on intra-PLC routing without disturbing inter-PLC
resources. As described in the Switching Routing Seg-
ments subsection, the BIDI routing segments are also
used for routes to a diagonally adjacent PFU.
In addition to the intra-PLC connections, the xBID and
output switching segments also have connectivity to
the x1, x5, and xL inter-PLC routing resources, provid-
ing an alternate routing path rather than using PLC
xSW segments. These connections also provide a path
to the 3-state buffers in the SLIC without encumbering
the xSW segments. In this manner, buffering or 3-state
control can be added to inter-PLC routing without dis-
turbing local functionality within a PFU.
Control Signal and Fast-Carry Routing
PFU control signal and the fast-carry routing are per-
f ormed using the FINS structure and se veral dedicated
routing paths. The fast-carry (FC) routing resources
consist of a dedicated bidirectional segment between
each orthogonal pair of PLCs. This means that a fast-
carry can go to or come from each PLC to the right or
left, above or below the subject PLC. The FINS struc-
ture is used to control the switching of these fast-carry
paths between the fast-carry input (FCIN) and fast-
carry output (FCOUT) ports of the PFU.
The PFU control inputs (CE, SEL, LSR, ASWE) and
CIN can be reached via the FINS by two special routing
segments, E1 and E2. The E1 routing segment pro-
vides connectivity between all of the xBID routing seg-
ments and the FINS. It is unidirectional from the BIDI
routing to the FINS. E1 also provides connectivity to the
PFU clock input via FINS for a local clock signal . The
E2 segment connects the SLIC DEC output to the FINS
and to a group of CIPS that provide bidirectional con-
nectivity with all of the BIDI routing segments. This
allows the DEC signal to be used in the PFU and/or
routed on the BIDI segments. It also allows signals to
be routed to the PFU on the xBID segments if the SLIC
DEC output is not used.
There is also a dedicated routing segment from the
FINS to the SLIC TRI input used for BIDI buffer 3-state
control.
Lucent Technologies Inc. 31
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
Inter-PLC Routin
g
Resources
The inter-PLC routing is used to route signals between
PLCs. The routing segments occur in groups of ten,
and differ in the numbers of PLCs spanned. The x1
routing segments span one PLC, the x5 routing seg-
ments span five PLCs, the xH routing segments span
one-half the width (height) of the PLC arra y, and the xL
routing segments span the width (height) of the PLC
arra y. All types of routing segments run in both horizon-
tal and vertical directions.
Table 8 shows the groups of inter-PLC routing seg-
ment s in ea ch PL C . I n the t ab l e , ther e ar e tw o ro ws /c ol-
umns for x1 lines. They are differentiated by a T f or top ,
B for bottom, L for left, and R for right. In the
ORCA
F oundry design editor representation, the horizontal x1
routing segments are located abo ve and below the
PFU. The two groups of vertical segments are located
on the left side of the PFU. The xL and x5 routing seg-
ments only run below and to the left of the PFU, while
the xH segments only run above and to the right of the
PFU. The inde xes specify individual routing segments
within a group. For example, the vx5[2] segment runs
v ertically to the left of the PFU , spans five PLCs, and is
the third line in the 10-bit wide group.
PLCs are arranged like tiles on the
ORCA
device.
Breaks in routing occur at the middle of the tile (e.g., x1
lines break in the middle of each PLC) and run across
tiles until the next break.
Figure 20 provides a global view of inter-PLC routing
resources across multiple PLCs.
x1 Routing Segments. There are a total of 40 x1 rout-
ing segments per PLC: 20 vertical and 20 horizontal.
Each of these are subdivided into two, 10-bit wide
buses: hx1T[9:0], hx1B[9:0], vx1L[9:0], and vx1R[9:0].
An x1 segment is one PLC long. If a signal net is longer
than one PLC, an x1 segment can be lengthened to n
times its length by turning on n – 1 CIPs . A signal is
routed onto an x1 route segment via the switching rout-
ing segments or BIDI routing segments which also
allows the x1 route segment to be connected to other
inter-PLC segments of different lengths. Corner turning
between x1 segments is provided through direct con-
nections, xSW segments, and xBID segments.
x5 Routing Segments. There are two sets of ten x5
routing segments per PLC. One set (vx5[9:0]) runs ver-
tically, and the other (hx5[9:0]) runs horizontally. Each
x5 segment tra verses five PLCs bef ore it is broken b y a
CIP. Two x5 segments in each group break in each
PLC. The two that break are in an equivalent pair; for
example, x5[0] and x5[4]. The x5 segments that break
shift by one at the next PLC. For e xample, if hx5[0] and
hx5 [4] ar e br ok en at th e cu rr ent PLC, h x5[ 1] and hx 5[5 ]
will be broken at the PLC to the right of the current
PLC. There are direct connections to the BIDI routing
segments in the PLC at which the x5 segments break,
on both sides of the break. Signal corner turning is
enabled by CIPs in each PLC that allow the broken x5
segments to directly connect to the broken x5 seg-
ments that run in the orthogonal direction. x5 corner
turning can also be accomplished via the xSW and
xBID segments in a PLC. In addition, the x5 segments
are connected to the FINS and PFU outputs on a bit-
by-bit basis by the xSW segments. x5 segments can be
connected f or signal runs in multiples of five PLCs, or
they can be combined with x1 and xH routing segments
for runs of varying distances.
Table 8. Inter-PLC Routing Resources
Horizontal
Routin
g
Se
g
ments
Vertical
Routin
g
Se
g
ments
Distance
S
p
anned
hx1U
[
9:0
]
vx1R
[
9:0
]
One PLC
hx1B
[
9:0
]
vx1L
[
9:0
]
One PLC
hx5
[
9:0
]
vx5
[
9:0
]
Five PLCs
hx5
[
9:0
]
vx5
[
9:0
]
Five PLCs
hxL
[
9:0
]
vxL
[
9:0
]
PLC Arra
y
hxH
[
9:0
]
vxH
[
9:0
]
1/2 PLC Arra
y
hCLK vCLK PLC Arra
y
32 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
5-5767(F)
Fi
g
ure 20. Multi
p
le PLC View of Inter-PLC Routin
g
PFU
PFU PFU
PFU PFU
PFU
PFUPFUPFU
hxH[9:0]
hx1[9:0]
hCLK
hx1[9:0]
hx5[9:0]
hxL[9:0]
hxH[9:0]
hx1[9:0]
hCLK
hx1[9:0]
hx5[9:0]
hxL[9:0]
hx1[9:0]
hx5[9:0]
hxL[9:0]
hxH[9:0]
hx1[9:0]
hCLK
vx1L[9:0]
vx5[9:0]
vCLK
vxH[9:0]
vx1[9:0]
vxL[9:0]
vx5[9:0]
vCLK
vxH[9:0]
vxL[9:0]
vx5[9:0]
vx1[9:0]
vCLK
vxH[9:0]
vx1[9:0]
vx1[9:0]
vx1[9:0]
vx1[9:0]
10
2
2
10
2
10
2
10
2
10
2
10
2
10
2
10
2
10
2
10
10
2
10
2
10
2
10
2
10
2
10
2
10
2
10
2
SLIC
SLIC
SLIC
SLIC
SLIC
SLIC
SLIC
SLIC
SLIC
PLC BOUNDARY
2 OF 10
LINE-BY-LINE
10
2
KEY: CONFIGURABLE SIGNAL-LINE BREAKS:
Lucent Technologies Inc. 33
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
xL Routing Lines. The xL routing lines run vertically
and horizontally the height and width of the array,
respectively. There are a total of 20 xL routing lines per
PLC: ten horizontal (hxL[9:0]) and ten vertical
(vxL[9:0]). Each of the xL lines connects to the PIC
routing at either end . The xL lines are int ende d prima-
rily for global signals that must travel long distances
and require minimum delay and/or skew, such as
clocks or 3-state buses.
Each xL line (also called a long line) drives a buffer in
each PLC that can drive onto the horizontal and verti-
cal local clock routing segments (lCLK) in the PLC.
Also , two out of each g roup of ten xL segments in each
PLC can be driven b y a b uff er attached to a clock spine
(described later) allowing local distribution of global
clock signals. More general-purpose connections to the
long lines can be made through the xBID segments in a
PLC. Each long line is connected to an xBID segment
on a bit-by-bit basis. These BIDI connections allow cor-
ner turning from horizontal to vertical long lines, and
connection between long lines and x1 or x5 segments.
xH Routing Segments. Ten by-half (xH) routing seg-
ments run horizontally (hxH[9:0]) and ten xH routing
segments run vertically (vxH[9:0]) in each row and col-
umn in the array. These routing segments travel a dis-
tance of one-half the PLC array before being broken in
the middle of the arra y in the interquad area (discussed
later). They also connect at the periphery of the FPGA
to the PICs, like the xL lines. xH routing segments con-
nect to the PLCs only by s witching segments. The y are
intended for fast signal interconnect.
Cloc k (and Global CE and LSR) Routing Segments.
For a very f ast and low-skew clock (or other global sig-
nal tree), clock routing segments run the entire height
and width of the PLC arra y. There are two clock routing
segments per PLC: one horizontal (hCLK) and one v er-
tical (vCLK). The source for these clock routing seg-
ments can be any of the I/O buffers in the PIC, the
Series 3 ExpressCLK inputs, user logic, or the pro-
grammable clock manager (PCM). The horizontal clock
routing segments (hCLK) are alternately driv en by the
left and right PICs . The v ertical clock routing segments
(vCLK) are alternately driven by the top and bottom
PICs.
The clock routing segments are designed to be a clock
spine. In each PLC, there is a fast connection availab le
from the clock segment to a long-line driv er (described
earlier). With this connection, one of the clock routing
segments in each PLC can be used to drive one of the
ten xL routing segments perpendicular to it, which, in
turn, creates a clock spine tree. This feature is dis-
cussed in detail in the Clock Distribution Network sec-
tion.
Special connectivity is provided in each PLC to connect
the clock enable signals (CE and ASWE) and the LSR
signal to the clock network for fast global control signal
distribution. CE and ASWE have a special connection
to the horizontal clock spine, and LSR has a special
connection to the vertical clock spine. This allows both
signals to be routed globally within the same PLC, if
desired; however, this will consume some of the
resources available for clock signal routing.
If using these spines, the clock enable signal must
come from the right or left edge of the device, and the
LSR signal must come from the top or bottom of the
device due to their horiz ontal and vertical connectivity,
respectively, to the clock network.
Minimizin
g
Routin
g
Dela
y
The CIP is an active element used to connect two rout-
ing segments. As an active element, it adds signifi-
cantly to the resistance and capacitance of a routing
network (net), thus increasing the net’s delay. The
advantage of the x1 segment over an x5 segment is
routing fle xibility. A net from one PLC to the next is eas-
ily routed by using x1 routing segments. As more CIPs
are added to a net, the delay increases. To increase
speed, routes that are greater than two PLCs away are
routed on the x5 routing segments because a CIP is
located only in every fifth PLC. A net that spans eight
PLCs requires seven x1 routing segments and six
CIPs. Using x5 routing segments, the same net uses
two routing segments and one CIP.
3434 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Logic Cells (continued)
PLC Architectural Description
Figure 21 is an architectural drawing of the PLC (as
seen in
ORCA
Foundry) that reflects the PFU, the rout-
ing segments, and the CIPs. A discussion of each of
the letters in the drawing follows.
A. These are switchin
g
routin
g
se
g
ments
(
xSW
)
that
g
ive the router flexibilit
y
. In
g
eneral switchin
g
theor
y
,
the more levels of indirection there are in the routin
g
,
the more routable the network is. The xSW se
g
-
ments can also connect to the xSW lines in ad
j
acen t
PLCs.
B. These CIPs connect the x1 routin
g
. These are
located in the middle of the PLC to allow the block to
connect to either the left end of the horizontal x1
se
g
ment from the ri
g
ht or the ri
g
ht end of the hori-
zont al x1 se
g
ment from the left, or both. B
y
s
y
mme-
tr
y
, the same principle is used in the vertical
direction.
C. This set of CIPs is used to connect the x1 and x5
nets to the xSW se
g
ments or to other x1 and x5
nets. The CIPs on the ma
j
or dia
g
onal allow data to
be transmitted on a bit-b
y
-bit basis from x1 nets to
the xSW se
g
ments and between the x1 and x5 nets.
D. This structure is the supplemental lo
g
ic and inter-
connect cell, or SLIC. It contains 3-statable bidirec-
tional buffers and lo
g
ic for buildin
g
decoders and
AND-OR-INVERT t
y
pe structures.
E. These are the primar
y
and secondar
y
elements of
the flexible input structure or FINS. FINS is a switch
matrix that provides hi
g
h connectivit
y
while retainin
g
routin
g
capabilit
y
. FINS also includes feedback
paths for softwired LUT implementation.
F. This is the PFU output switch matrix. It is a complex
switch network which, like the FINS at the input, pro-
vides hi
g
h connectivit
y
and maintains routabilit
y
.
G.This set of CIPs allows an xBID se
g
ment to transfer
a si
g
nal to/from xSW se
g
ments on each side. The
BIDIs can access the PFU throu
g
h the xSW se
g
-
ments. These CIPs allow data to be routed throu
g
h
the BIDIs for amplification or 3-state control and
continue to another PLC. The
y
also provide an alter-
native routin
g
resource to improve routabilit
y
.
H. These CIPs are used to transfer data from/to the
xBID se
g
ments to/fr om the x1 and xL routi n
g
se
g
-
ments. These CIPs have been optimized to allow
the BIDI buffers to drive the loads usuall
y
seen
when usin
g
each t
y
pe of routin
g
se
g
ment.
I. Clock input to PFU.
J. These are the ten switched output routin
g
se
g
ments
from the PFU. The
y
connect to the PLC switchin
g
se
g
ments and are input to the SLIC.
K. These lines deliver the auxiliar
y
si
g
nals clock enable
(
CE
)
, local set/reset
(
LSR
)
, front-end select
(
SEL
)
,
add/subtract/write enable
(
ASWE
)
, as well as the
carr
y
si
g
nals
(
CIN and FCIN
)
to the latches/FFs.
L. Thi s is the local clock buffer. An
y
of the horizontal
and vertical xL lines can drive the clock input of the
PLC latches/FFs. The clock routin
g
se
g
ments
(
vCLK and hCLK
)
and multiplexers/drivers are used
to connect to the xL routin
g
se
g
ments for low-skew,
low-dela
y
g
lobal si
g
nals.
M.These routi n
g
se
g
ments are used to route the fast-
carr
y
si
g
nal to/from the nei
g
hborin
g
four PLCs. The
carr
y
-out
(
COUT
)
and re
g
istered carr
y
-out
(
REG-
COUT
)
can also be routed out of the PFU.
N. This is the E2 control routin
g
se
g
ment. It runs from
the SLIC DEC output to the FINS and also provides
connectivit
y
to all xBID se
g
ments.
O.The xH routin
g
se
g
ments run one-half the len
g
th
(
width
)
of the arra
y
before bein
g
broken b
y
a CIP.
P. These CIPs connect the xH se
g
ments to the xSW
se
g
ments.
Q.The xBID se
g
ments are used to connect the SLIC to
the xSW se
g
ments, x1 se
g
ments, x5 se
g
ments, and
xL lines, as well as providin
g
for dia
g
onal PLC to
PLC connections.
R. These CIPs provide connections from the xBID se
g
-
ments to the E1/E2 routin
g
se
g
ments that feed PFU
control inputs CE, LSR, CIN, ASWE, SEL, and the
clock input. Alternativel
y
, these CIPs connect the
BIDI lines to the decoder
(
DEC
)
output of the SLIC,
for routin
g
the DEC si
g
nal.
S. These ar e clock spin es
(
vCLK and hCLK
)
with the
multiplexers and drivers to connect to the xL routin
g
se
g
ments.
T. These CIPs connect xBID se
g
ments to switchin
g
se
g
ments in dia
g
onall
y
and ortho
g
onall
y
ad
j
acent
PFUs.
U. These CIPs connect xSW se
g
ments to the PFU out-
put se
g
ments.
V. These CIPS connect xSW se
g
ments in ortho
g
onall
y
ad
j
acen t PFUs.
W.This is the SLIC 3-state control routin
g
se
g
ment
from the FINS to the SLIC 3-state control.
X. This is the E1 control routin
g
se
g
ment. It provides a
PFU input path from all xBID se
g
ments.
Y. These CIPs are used to select which xBID se
g
ments
are connected to the E1/E2 si
g
nal as described in
(
R
)
.
Lucent Technologies Inc. 35
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Pro
g
rammable Lo
g
ic Cells
(
continued
)
5-5758(F)
Figure 21. PLC Architecture
H
S
M
G
R
L
H H
D
R
SLIC OUTPUT
SWITCHING
PFU
PRIMARY FINS
SECONDARY FINS
B
W
Y
A
B
PM
O
Q
M
O
F
PV
K
J
U U U
XA
B
H B
G
C
H
Q
Q
T M S
Q
Q
L
H
T
E E
N
Q
CCC
A
C C
C
A
A
A
A
C
A
A
C
C C
C
A
3636 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Input/Output Cells
The programmable input/output cells (PICs) are
located along the perimeter of the device. The PIC’s
name is represented by a two-letter designation to indi-
cate on which side of the device it is located followed by
a number to indicate in which row or column it is
located. The first letter, P, designates that the cell is a
PIC and not a PLC. The second letter indicates the side
of the array where the PIC is located. The four sides
are left (L), right (R), top (T), and bottom (B). The indi-
vidual I/O pad is indicated by a single letter (either A, B,
C, or D) placed at the end of the PIC name. As an
example, PL10A indicates a pad located on the left
side of the array in the tenth row.
Each PIC interf aces to four bond pads and contains the
necessary routing resources to provide an interface
between I/O pads and the PLCs. Each PIC is com-
posed of four programmable I/Os (PIOs) and significant
routing resources. Each PIO contains input buffers,
output buff ers, routing resources, latches/FFs, and
logic and can be configured as an input, output, or
bidirectional I/O.
PICs in the Series 3 FPGAs have significant local rout-
ing resources, similar to routing in the PLCs. This new
routing increases the ability to fix user pinouts prior to
placement and routing of a design and still maintain
routability. The flexibility provided by the routing also
provides for increased signal speed due to a greater
var iety of sign al path s possi ble.
Included in the PIC routing is a fast path from the input
pins to the SLICs in each of the three adjacent PLCs
(one orthogonal and two diagonal). This f eature allows
for input signals to be very quickly processed by the
SLIC decoder function and used on-chip or sent back
off of the FPGA. Also new to the Series 3 PIOs are
latches and FFs and options for using fast, dedicated
clocks called ExpressCLKs. These features will all be
discussed in subsequent sections.
A diagram of a single PIO (one of four in a PIC) is
shown in Figure 22. Table 9 provides an ov erview of the
programmable functions in an I/O cell.
5-5805(F).c
Fi
g
ure 22. OR3C/Txxx Pro
g
rammable In
p
ut/Out
p
ut
(
PIO
)
Ima
g
e from
ORCA
Foundr
y
IN2
IN1
D0
D1
CK
SP
SD
LSR
INREGMODE
LATCHFF
LATCH
FF
D
CK
NORMAL
INVERTED
RESET
SET
LEVEL M ODE
TTL
CMOS
UP
DOWN
NONE
PULL-MODE
BUFFER
TS
FAST
SLEW
SINK
RESET
SET
LSR
SP
CK
D
OUT1
OUT2
ECLK
SCLK
CE
CE_OVER_LSR
LSR_OVER_CE
ASYNC
LSR
ENABLE_GSR
DISABLE_GSR
OUT1OUTREG
OUT2OUTREG
OUT1OUT2
NOR
XOR
XNOR
AND
NAND
OR
PIO LOGIC
CLKIN
0
0
1
0
PAD Q
Q1
PD
TO ROUTING
Q
1
ECLK
SCLK
PMUX
FROM ROU TIN G
MODE
LSR
CK
D0 Q
Lucent Technologies Inc. 37
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Input/Output Cells
(continued) 5 V Tolerant I/O
The I/O on the OR3Txxx Series devices allow intercon-
nection to both 3.3 V and 5 V devices (selectable on a
per-pin basis).
The OR3Txxx devices will drive the pin to the 3.3 V lev-
els when the output buffer is enabled. If the other
device being driven by the OR3Txxx device has TTL-
compatible inputs, then the device will not dissipate
much input buff er pow er. This is because the OR3Txxx
output is being driven to a higher level than the TTL
level required. If the other device has a CMOS-compat-
ible input, the amount of input buffer power will also be
small. Both of these power v alues are dependent upon
the input buff er characteristics of the other de vice when
driven at the OR3Txxx output buffer voltage levels.
The OR3Txxx device has internal programmable pull-
ups on the I/O buffers. These pull-up voltages are
always referenced to VDD and are always sufficient to
pull the input buffer of the OR3Txxx device to a high
state. The pin on the OR3Txxx device will be at a level
1.0 V below VDD (minimum of 2.0 V with a minimum
VDD of 3.0 V). This voltage is sufficient to pull the e xter-
nal pin up to a 3.3 V CMOS high input le v el (1.8 V, min)
or a TTL high input level (2.0 V, min) in a 5 V tolerant
system. Therefore, in a 5 V tolerant system using 5 V
CMOS parts, care must be tak en to evaluate the use of
these pull-ups to pull the pin of the OR3Txxx device to
a typical 5 V CMOS high input level (2.2 V, min).
PCI Compliant I/O
The I/O on the OR3Txxx Series devices allows compli-
ance with PCI Local Bus (Rev. 2.2) 5 V and 3.3 V sig-
naling environments. The signaling environment used
f or each input buff er can be selected on a per-pin basis.
The selection provides the appropriate I/O clamping
diodes for PCI compliance. Choosing an IBT input
buff er will provide PCI compliance in OR3Txxx de vices.
OR3Cxx de vices have PCI Local Bus compliant I/Os f or
5 V signaling.
Table 9. PIO Options
In
p
ut O
p
tion
Input Level TTL, OR3Cxx onl
y
CMOS, OR3Cxx o r OR3Txxx
3.3 V PCI Compliant, OR3Txxx
5 V PCI Compliant, OR3Txxx
Input Speed Fast, Dela
y
ed
Float Value Pull-up, Pull-down, None
Re
g
ister Mode Latch, FF, Fast Zero Hold FF,
None
(
direct input
)
Clock Sense Inverted, Noninverted
Input Selection Input 1, Input 2, Clock Input
Out
p
ut O
p
tion
Output Drive
Current 12 mA/6 mA or 6 mA/3 mA
Output Function Normal, Fast Open Drain
Output Speed Fast, Slewlim, Sinklim
Output Source FF Direct-out, General Routin
g
Output Sense Active-hi
g
h, Active-low
3-State Sense Active-hi
g
h, Active-low
(
3-state
)
FF Clockin
g
ExpressCLK, S
y
stem Clock
Clock Sense Inverted, Noninverted
Lo
g
ic Options See Table 10.
I/O Controls O
p
tion
Clock Enable Active-hi
g
h, Active-low,
Alwa
y
s Enabled
Set/Reset Level Active-hi
g
h, Active-low,
No Local Reset
Set/Reset T
y
pe S
y
nchronous, As
y
nchronous
Set/Reset Priorit
y
CE over LSR, LSR over CE
GSR Control Enable GSR, Disable GSR
3838 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Input/Output Cells
(continued)
Inputs
As outlined earlier in Table 9, there are six major
options on the PIO inputs that can be selected in the
ORCA
Foundry tools. For OR3Cxx devices, the inputs
and bidirectional buffers can be configured as either
TTL or CMOS compatible. OR3Txx x devices support
CMOS lev els only for input or bidirectional buff ers, hav e
5 V tolerant I/Os as previously explained, but can
optionally be selected on a pin-by-pin basis to be PCI
bus 3.3 V signaling compliant (PCI bus 5 V signaling
compliance occurs in 5 V tolerant operation). The
default buffer upon powerup for the unused sites is 5 V
tolerant/5 V PCI compliant. Consult the
ORCA
macro
library, Series 3 I/O cells, for the appropriate buffers.
Inputs may have a pull-up or pull-down resistor
selected on an input for signal stabilization and power
management. Input signals in a PIO can be passed to
PIC routing on any of three paths, two general signal
paths into PIC routing, and/or a fast route into the cloc k
routing sy st em.
There is also a programmable delay available on the
input. When enab led, this delay aff ects the IN1 and IN2
signals of each PIO, but not the clock input. The delay
allows any signal to have a guaranteed zero hold time
when input. This feature is discussed subsequently.
Inputs should have transition times of less than 500 ns
and should not be left floating. If any pin is not used, it
is 3-stated with an internal pull-up resistor enabled
automatically after configuration.
Warning: During configuration, all OR3Txxx inputs
have internal pull-ups enabled. If these inputs are
driven to 5 V, they will draw substantial current
(≅ 5 mA). This is due to the fact that the inputs are
pulled up to 3 V.
Floating inputs increase power consumption, produce
oscillations, and increase system noise. The OR3Cxx
inputs have a typical hysteresis of approximately 280
mV (200 mV for the OR3Txxx) to reduce sensitivity to
input noise. The PIC contains input circuitry which pro-
vides protection against latch-up and electrostatic dis-
charge.
The other features of the PIO inputs relate to the new
latch/FF structure in the input path. As shown in
Figure 23, the input is optionally passed to a register or
latch/register pair. These structures can operate in the
modes listed in Table 9. In latch mode, the input signal
is fed to a latch that is clocked b y a system clock signal.
The clock may be inverted or noninverted from its
sense in the PIC routing. There is also a local set/reset
signal to the latch from the PIC routing. The senses of
these signals are also programmable as well as the
capability to enable or disable the global set/reset sig-
nal and select the set/reset priority. The same control
signals may also be used to control the input latch/FF
when it is configured as a FF instead of a latch, with the
addition of another control signal used as a clock
enable.
Lucent Technologies Inc. 39
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Input/Output Cells (continued)
Zero-Hold In
p
ut
There are two options f or zero-hold input capture in the PIO . If input delay mode is selected to dela y the signal from
the input pin, data can be either registered or latched with guaranteed zero-hold time in the PIO using a system
clock.
To guarantee zero hold, the system clock spine structure must be used f or clocking, as will be discussed later. The
fast zero-hold mode of the PIO input takes advantage of the latch/FF combination and sources the input FF data
from a dedicated latch that is clocked by the ExpressCLK from the PIC. The ExpressCLK is a clock from a dedi-
cated input pin designed for fast, low-skew operation at the I/Os and is described more fully in the Clock Distribu-
tion Network and PIC Interquad (MID) Routing sections that follow. The combination of ExpressCLK latch and
system clock FF guarantees a zero-hold capture of input data in the PIO FF, while at the same time reducing input
setup time. Figure 23 shows a schematic of the fast-capture latch/FF and a sample timing diagram.
5-5974(F)
Note: CE and LSR signals not shown.
Figure 23. Fast-Capture Latch and Timing
D Q
INPUT DATA
LATCH
CLK
O
I
EXPRESSCLK
O
I
SYSTE M CLK
CD = 1
CLOCK ENABLE
LOCAL SET/RESET
DQ
FF
S/R
CE
DATA OUT
TO PIC ROUTING
EXPRESSCLK
SYSTEM CLK
INPUT DATA
QLATCH
QFF
BACDE
BACDE
ABCD
40 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Input/Output Cells (continued)
In
p
ut Demulti
p
lexin
g
The combination of input register capability and the two inputs, IN1 and IN2, from each PIO to the internal routing
provides for input signal demultiplexing without any additional resources. Figure 24 shows the input configuration
and general timing for demultiplexing a multiplexed address and data signal. The PIO input signal is sent to both
the input latch and directly to IN2. The signal is latched on the f alling edge of the clock and output to routing at IN1.
The address and data are then both available at the rising edge of the system clock. These signals may be regis-
tered or otherwise processed in the PLCs at that clock edge. Figure 24 also shows the possible use of the SLIC
decoder to perform an address decode to enable which registers are to receive the input data. Although the timing
shown is f or using the input register as a latch, it ma y also be used in the same way as an FF. Also note that the sig-
nals found in PIO inputs IN1 and IN2 can be interchanged.
5-5798(F)
Figure 24. PIO Input Demu lt iplexing
DEC
DQ
PAD
PIO
DQ
CE
SLIC
OTHER ADDRESS
LINES
SCLK
IN1
IN2
SCLK
PIO LATCH
PLC FF
ADDR1 ADDR2 ADDR3 ADDR4 ADDR5
DATA1 DATA2 DATA3 DATA4
DATA1 DATA2 DATA3ADDR2 ADDR3 ADDR4 ADDR5
DATA0
DATA4
OUTPUT
OUTPUT
PIO INPUT
PLC
Lucent Technologies Inc. 41
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Input/Output Cells
(continued)
Outputs
The PIC’s output drivers ha ve programmable drive
capability and slew rates. Three propagation delays
(fast, slewlim, sinklim) are available on output drivers.
The sinklim mode has the longest propagation delay
and is used to minimize system noise and minimize
power consumption. The fast and slewlim modes allow
critical timing to be met.
The drive current is 12 mA sink/6 mA source for the
slewlim and fast output speed selections and
6 mA sink/3 mA source f or the sinklim output. Two adja-
cent outputs can be interconnected to increase the out-
put sink/source current to 24 mA/12 mA.
All outputs that are not speed critical should be config-
ured as sinklim to minimize power and noise. The num-
ber of outputs that switch simultaneously in the same
direction should be limited to minimize ground bounce.
To minimize ground bounce problems, locate heavily
loaded output buffers near the ground pads. Ground
bounce is generally a function of the driving circuits,
traces on the printed-circuit board, and loads and is
best determined with a circuit simulation.
At powerup, the output drivers are in slewlim mode,
and the input buffers are configured as TTL-level com-
patible (CMOS for OR3Txxx) with a pull-up. If an output
is not to be driven in the selected configuration mode, it
is 3-stated.
The output buffer si
g
nal can be inverted, and the
3-state control signal can be made active-high, active-
low, or always enabled. In addition, this 3-state signal
can be registered or nonregistered. Additionally, there
is a fast, open-drain output option that directly connects
the output signal to the 3-state control, allowing the out-
put buffer to either drive to a logic 0 or 3-state, b ut
never to drive to a logic 1. Because there is no explicit
route required to create the open-drain output, its
response is very fast. Like the input side of the PIO,
there are two output connections from PIC routing to
the output side of the PIO, OUT1, and OUT2. These
connections provide for flexible routing and can be
used in data manipulation in the PIO as described in
subsequ ent paragraphs.
An FF has been added to the output path of the PIO.
The register has a local set/reset and cloc k enable. The
LSR has the option to be synchronous or asynchro-
nous and have priority set as clock enab le over LSR or
LSR over clock enable. Clocking to the output FF can
come from either the system clock or the ExpressCLK
associated with the PIC. The input to the FF can come
from either OUT1 or OUT2, or it can be tied to VDD or
GND. Additionally, the input to the FF can be inverted.
Out
p
ut Multi
p
lexin
g
The Series 3 PIO output FF can be combined with the
new PIO logic block to perform output data multiplexing
with no PLC resources required. The PIO logic bloc k
has three multiplexing modes: OUT1OUTREG,
OUT2OUTREG, an d OUT1OUT2. OUT1OUTREG a nd
OUT2OUTREG are equivalent e xcept that either OUT1
or OUT2 is MUXed with the FF, where the FF data is
output on the clock phase after the active edge. The
simplest multiplexing mode is OUT1OUT2. In this
mode, the signal at OUT1 is output to the pad while the
clock is low, and the signal on OUT2 is output to the
pad when the clock is high. Figure 25 shows a simple
schematic of a PIO in OUT1OUT2 mode and a general
timing diagram for multiplexing an address and data
signal.
Often an address will be used to generate or read a
data sample from memory with the goal of multiplexing
the data onto a single line. In this case, the address
often precedes the data by one clock cycle.
OUT1OUTREG and OUT2OUTREG modes of the PIO
logic can be used to address this situation.
Because OUT1OUTREG mode is equivalent to
OUT2OUTRE G, only OUT2OUTREG mode is
described here. Figure 26 shows a si mple PIO sche-
matic in OUT2OUTREG mode and general timing for
multiplexing data with a leading address. The address
signal on OUT1 is registered in the PIO FF. This dela ys
the address so that it aligns with the data signal. The
PIO logic block then sends the OUTREG signal
(address) to the pad when the clock is high and the
OUT2 signal (data) to the pad when the clock is low,
resulting in an aligned, multiplexed signal.
42 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Input/Output Cells (continued)
NOTE: PIO LOGIC MODE, OUT1OUT2 5-5799(F)
Figure 25. Output Multiplexing (OUT1OUT2 Mode)
NOTE: PIO LOGIC MODE, OUT1OUT2 5-5797(F)
Figure 26. Output Multiplexing (OUT2OUTREG Mode)
CLK
ADDR1 ADDR2 ADDR3 ADDR4 ADDR5
DATA2 DATA3 DATA4 DATA5
ADDR1 ADDR2 ADDR3DATA1 DATA2 DATA3 DATA4
DATA1
ADDR4
OUT1
OUT2
PIC OUTPUT
PLC
ADDRESS
PAD
PIO
LOGIC
OUT1
OUT2
CLK
FROM
ROUTING
DATA
FROM
ROUTING
PIC
PLC
DQ
CLK
PAD
P/O
LOGIC
OUT1
OUT2
PIC
DATA
CLK
REG ADDRESS
DATA
ADDR1 ADDR2 ADDR3 ADDR4
DATA1 DATA2 DATA3 DATA4
DATA1 DATA2ADDR1 ADDR2 ADDR3 ADDR4DATA3PAD
ADDR ADDR1 ADDR2 ADDR3 ADDR4 ADDR5
FROM
ROUTING
ADDRESS
FROM
ROUTING
Lucent Technologies Inc. 43
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Pro
g
rammable In
p
ut/Out
p
ut Cells
(
continued
)
PIO Lo
g
ic Function Generator
The PIO logic block can also generate logic functions
based on the signals on the OUT2 and CLK ports of
the PIO. The functions are AND, NAND, OR, NOR,
XOR, and XNOR. Table 10 is provided as a summary
of the PIO logic options.
PIO Register Control Signals
As discussed in the Inputs an d Outputs subsections,
the PIO latches/FFs have various clock, clock enable
(CE), local set/reset (LSR), and global set/reset
(GSRN) controls. Table 11 provides a summary of
these control signals and their effect on the PIO
latches/FFs. Note that all control signals are optionally
invertible.
Table 10. PIO Logic Options
O
p
tion Descri
p
tion
OUT1OUTREG Data at OUT1 output when clock
low, data at FF out when clock
hi
g
h.
OUT2OUTREG Data at OUT2 output when clock
low, data at FF out when clock
hi
g
h.
OUT1OUT2 Data at OUT1 output when clock
low, data at OUT2 when clock
hi
g
h.
AND Output lo
g
ical AND of si
g
nals on
OUT2 and clock.
NAND Output lo
g
ical NAND of si
g
nals
on OUT2 and cloc k.
OR Output lo
g
ical OR of si
g
nals on
OUT2 and clock.
NOR Output lo
g
ical NOR of si
g
nals on
OUT2 and clock.
XOR Output lo
g
ical XOR of s i
g
nals on
OUT2 and clock.
XNOR Output lo
g
ical XNOR of si
g
nals
on OUT2 and cloc k.
Table 11. PIO Register Control Signals
Control Si
g
nal Effect/Functionalit
y
ExpressCLK Clocks input fast-capture latch;
optionall
y
clocks output FF, or
3-state FF.
S
y
stem Clock
(
SCLK
)
Clocks input latch/FF; optionall
y
clocks output FF, or 3-state FF.
Clock Enable
(
CE
)
Optionall
y
enables/disables input
FF
(
not available for input latch
mode
)
; optionall
y
enables/dis-
ables output FF; separate CE
inver sion ca pabi li t
y
for input and
output.
Local Set/Reset
(
LSR
)
Option to disable; affects input
latch/FF, output FF, and 3-state
FF if enabled.
Global Set/Reset
(
GSRN
)
Option to enable or disable per
PIO after initial confi
g
uration.
Set/Reset Mode The input latch/FF, output FF, and
3-state FF are individuall
y
set or
reset b
y
both the LSR and GSRN
inputs.
4444 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Input/Output Cells
(continued)
PIC Routing Resources
The PIC routing borrows many of the concepts and
constructs from the PLC routing. It is designed to be
able to gather an 8-bit bidirectional bus from any eight
consecutive I/O pads and route them to either or both
of the two adjacent PLCs. The eight I/O bits do not
need to start at a PIC boundary; that is, they may start
at one of the middle two PIOs in a PIC and span three
PICs.
Substantial routing has been added to the PIC to off-
load PLC routing from being used to move signals
around the PLC array perimeter. This saves PLC rout-
ing for logic purposes and provides greater fle xibility for
locking design pinouts prior to final placement and rout-
ing of the device, or allowing a change in the pinout late
in the design cycle. The PIC routing has also been
increased substantially to allow routing to the complex
PIO cells that now allow multiple inputs and outputs per
device pin, along with new sequential control signals,
such as clock enable, LSR, and clock.
PICs are grouped in pairs for purposes of discussing
PIC routing. On the sides of a de vice, the PICs in a pair
are referred to as top and bottom. On the top or bottom
of a device, the PICs in a pair are referred to as left or
right. For example, on the top edge of the device, the
leftmost PIC , PT1, is the left PIC of a pair, and PIC PT2
is the right PIC of that pair. The next PIC to the right,
PT3, is the left PIC of the next pair, and so on.
The need for PIC pairs stems from the routing of
switching segments and PLC half- and long-line driv-
ers. As described below, the connectivity for these
types of routing is grouped across pairs of PICs to pro-
vide complete and fast routing of I/O signals between a
given PIC and the three adjacent PLCs: one orthogonal
and two diagonal.
PIC routing segments use the same terminology as
PLC routing segments , but are prefixed with a p to dis-
tinguish them as belonging to the PICs.
PIC Switching Segments. Each PIC has two groups
of switching segments (pSW), each group having eight
lines with connectivity to the PIOs in groups of four.
One set of switching segments connects to the PIC to
the left (above), and the other set connects to the
s witching segments of the PIC to the right (below). This
means of connectivity between PICs using staggered
connections of groups of switching segments allows a
given PIC to route signals to both adjacent PICs and all
adjacent PLCs efficiently. This provides single signal
routing flexibility and ro uti ng of multipl e buses on
groups of I/Os without tying up global routing
resources.
px1 Routing Segments. There are fiv e px1 routing
segments in each PIC that run parallel to the edge of
the chip on which the PIC resides, each broken by a
CIP in each PIC. The px1 segments have connectivity
to the pSW segments and to the x1 routing segments
of the two adjacent PLCs .
px2 Routing Segments. There are fiv e px2 routing
segments in each PIC that run parallel to the edge of
the chip on which the PIC resides. To provide greater
routing fle xibility, the CIPs that break the px2 segments
e very two PICs are staggered across the two PICs in a
pair. One PIC of the pair has break CIPs on the e ven-
numbered px2 segments, and the other has them on
the odd-numbered px2 segments. The px2 segments
have connectivity to the pSW segments and to the x1
routing segments of the two adjacent PLCs.
px5 Routing Segments. There are ten px5 routing
segments in each PIC that run parallel to the edge of
the chip on which the PIC resides. Two of the ten seg-
ments are broken in each PIC so that each segment is
broken every five PICs. All ten px5 segments break at
the corners of the chip, allowing independent px5 rout-
ing on each edge of the chip. The px5 routing seg-
ments connect to the pSW segments and the x5 and
xH routing segments of the two adjacent PLCs .
pxH Routing Segments. Each PIC contains eight pxH
routing segments that run parallel to the edge of the
chip on which the PIC resides . The pxH segments hav e
connectivity with the xL, xH, and one set of xBID rout-
ing segments in the immediately adjacent PLC.
pxL Routing Segments. There are ten pxL routing
segments in each PIC that run parallel to the edge of
the chip on which the PIC resides. Each of the xL lines
makes a connection to an xL line from the adjacent
PLC. PIC long lines (xL) can be used for global signal
distribution just as PLC xL lines can.
Lucent Technologies Inc. 45
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Input/Output Cells
(continued)
PIC Architectural Description
The PIC architecture as seen in
ORCA
Foundry is
shown in Figure 27. The figure is the left PIC of a PIC
pair on the top edge of a Series 3 array. Both PICs in a
pair are similar, with the differences mainly lying in the
connections between the PIC switching segments
(pSW), the IN2 connections across PIC boundaries,
and the system clock spine driver residing in only one
PIC of a pair.
A. This is a pr o
g
rammable input/output
(
PIO
)
. There
are four PIOs per PIC. The PIOs contain the PIC
lo
g
ic and I/O buffers.
B. This is the PIC output switchin
g
block. I t conne cts
the PIC switchin
g
se
g
ments and local clock lines to
the PIO output and control si
g
nals.
C. This is the s
y
stem cloc k spine switchin
g
block and
buffer . There is onl
y
one s
y
stem cl ock spine pe r pair
of PICs. Its inputs can come from the PIC switchin
g
se
g
ments or an
y
of the ei
g
ht PIO inputs in a PIC
pair.
D.PIC switchin
g
se
g
ments
(
pSW
)
. These routin
g
se
g
-
ments are used to interconnect routin
g
resources
within the PIC and to a lesser de
g
ree, between
PICs.
E. px1 routin
g
se
g
ments. The PIC x1 routin
g
se
g
-
ments traverse one PIC and break at a CIP in the
middle of each PIC.
F. px2 routin
g
se
g
ments. The PICs have r outin
g
that
traverses two PICs between breaks. The breaks are
sta
gg
ered amon
g
the five px2 se
g
ments.
G. px5 routin
g
se
g
ments. Each of the ten PIC x5 rout-
in
g
se
g
ments traverses five PICs in between breaks
at a CIP. Two px5 se
g
ments break in each PIC.
H. pxH routin
g
se
g
ments. The ei
g
ht PIC xH routin
g
se
g
ments traverse half of the arra
y
and break at
CIPs in the inter
q
uad routin
g
re
g
ion that is in the
middle of the arra
y
.
I.
(
Not used intentionall
y
for clarit
y
.
)
J. pxL routin
g
se
g
ments. The PIC lon
g
lines run the
entire len
g
th of the side of the arra
y
.
K.x5 routin
g
se
g
ments from the ad
j
acen t PLC routin
g
.
L.xL routin
g
se
g
ments from the ad
j
acen t PLC routin
g
.
M.x1 routin
g
se
g
ments from the ad
j
acen t PLC routin
g
.
N.Switchin
g
se
g
ments from the ad
j
acent PLC routin
g
.
O.xH routin
g
se
g
ments from the ad
j
acen t PL C ro uti n
g
.
P. BIDI routin
g
se
g
ments from the ad
j
acent PLC rout-
in
g
.
Q. These are the IN2 routin
g
se
g
ments. There is one
IN2 line from each PIO, and all ei
g
ht IN2 lines from
each PIC pair are present in both PICs of a pair.
R. These CIPs connect the IN1 and IN2 routin
g
se
g
-
ments from the PIOs to the PIC switchin
g
se
g
-
ments.
S. These CIPs break the PIC switchin
g
se
g
ments at
the interface between a PIC pair.
T. These CIPs connect ad
j
acent PLC routin
g
resources to the PIC switchin
g
se
g
ments.
U. These CIPs connect inter-PIC routin
g
with the PIC
switchin
g
se
g
ments.
V. These CIPs break the px1, px2, and px5 routin
g
at
the middle of a PIC. The px2 and px5 CIP place-
ment varies dependin
g
on the PLC.
W. These mutuall
y
exclusive buffers can drive one lon
g
line si
g
nal onto a PIC local clock routin
g
se
g
ment.
X. These mutuall
y
exclus iv e buffers can select a
source from one of the local s
y
stem clock routes to
drive the PIO 3-state control si
g
nal.
Y. These are the four local s
y
stem clock routin
g
se
g
-
ments. Two come from connections within the PIC,
one from the other PIC in the pair, and one from the
ad
j
acent PLC.
Z. These mutuall
y
exclusive buffers allow a si
g
nal on
the PIC switchin
g
se
g
ments to be routed to a s
y
s-
tem clock spine or to a PIO s
y
stem clock.
AA.ExpressCLK routi n
g
line.
AB.S
y
stem cloc k spi ne.
AC. These various
g
roups of CIPs connect routin
g
resources from the ad
j
acent PLC to the inter-PIC
routin
g
resources.
AD. These buffers provide connectivit
y
between the
PLC xL
(
xH
)
lines and the PIC xL
(
xH
)
lines or
connectivit
y
between one of the IN2 routin
g
se
g
-
ments and the PIC and/or PLC xL
(
xH
)
routin
g
se
g
ments.
AE. These mutuall
y
exclusive buffers and CIPs provide
connectivit
y
to the PLC xL and xH lines from one
of the IN2 input se
g
ments.
AF. These buffers allow the IN2 si
g
nals to drive onto
the BIDI routin
g
of the ad
j
acent PLC, or the BIDI
routin
g
of the ad
j
acent PLC, and the PIC switchin
g
se
g
ments and/or PIC half lines ma
y
be connected.
46 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Input/Output Cells (continued)
5-5823(F)
Figure 27. PIC Architecture
AA AA
AA
B
Y
D
D
D
D
E
F
H
J
Z
X
AC
G
AE
AD
T
W
R
T
V
UU
AC
J
Q
Q
R R
C
P
O
N M
AD
MKLK
S
AF
W
T
H
AE
AC
AB
Lucent Technologies Inc. 47
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
High-Level Routing Resources
The high-level routing resources in the
ORCA
Series 3 devices are interquad routing, corner cell routing, and PIC
interquad routing. These resources and their related structures are discussed in the following subsections.
Interquad Routing
In the
ORCA
Series 3 devices, the PLC arra y is split into four equal quadrants. In between these quadrants, routing
has been added to route signals between the quadrants and distrib ute clocks. In addition to general routing, there
are four specialized clock routing spines. The general routing is discussed below, f ollowed b y the special clock rout-
ing.
One of the main purposes of interquad routing is to distrib ute internally generated signals, such as clocks and con-
trol signals. There are two types of interquad blocks: vertical and horizontal. Vertical interquad blocks (vIQ) run
between quadrants on the left and right, while horizontal interquad blocks (hIQ) run between top and bottom quad-
rants. Interquad lines begin and end in the MID cells that are discussed later. Since hIQ and vIQ blocks have the
same logic, only the hIQ block is described below. The interquad routing connects to x5 and xH segments. It does
not affect other local routing (xsw, x1, fast carry), so local routing is the same, whether PLC-PLC connections cross
quadrants or not. Figure 28 presents a (not to scale) view of interquad routing.
5-4538(F)
Fi
g
ure 28. Inter
q
uad Routin
g
TMID
BMID
5555
vIQ2[4:0]
vIQ4[4:0]
vIQ6[4:0]
vIQ8[4:0]
vIQ0[4:0]
vIQ3[4:0]
vIQ5[4:0]
vIQ7[4:0]
vIQ9[4:0]
vIQ1[4:0]
5
5555 5
LMID RMID
hIQ7[4:0]
hIQ5[4:0]
hIQ3[4:0]
hIQ1[4:0]
hIQ9[4:0]
hIQ6[4:0]
hIQ4[4:0]
hIQ2[4:0]
hIQ0[4:0]
hIQ8[4:0] 5
5
5
5
5
5
5
5
5
5
FAST CLOCK R
FAST CLOCK L
FAST CLOCK T
FAST CLOCK B
4848 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
High-Level Routing Resources (continued)
Figure 29 shows the connections from the interquad
routing to the inter-PLC routing for a block of the hori-
zontal interquad. The vertical interquad has similar
connections. The connections shown in Figure 29 are
made with PLCs located above and below the routing
shown in the figure. The interquad routing segments,
prefixed IH f or interquad horizontal, are in ten groups of
five lines. Any one line from each group can be routed
to one of the xH segments from the top of the device
(left for vertical interquad), one of the xH segments
from the bottom of the device (right for vertical inter-
quad), and one of the x5 segments crossing the inter-
quad.
Figure 28 shows four fast middle clock (fast clock) sig-
nals with the suffixes T (top), B (bottom), R (right), and
L (left), respectively. Figure 29 also shows the fast
clock R and fast clock L lines; these are dedicated
interquad clock spines. They originate in the CLKCN-
TRL special function b loc ks in the middle of each edge
of the device, with the name referencing the edge of
origin. For example, fast clock R originates in the
CLKCNTRL block on the right edge of a device . Fast
clock spines traverse the entire PLC array but do not
connect to the PICs on the edge of the device opposite
to the source. Each fast clock line connects to two of
the xL lines in each PLC that run orthogonally to the
fast clock. These connections allow the fast clock lines
to generate a clock tree that can reach any PLC in the
device. Fast clocks and other clock resources are dis-
cussed in the Clock Distribution Network section.
Programmable Corner Cell Routing
Pro
g
rammable Routin
g
The programmable corner cell (PCC) contains the cir-
cuitry to connect the routing of the two PICs in each
corner of the device. The PIC px1 and px2 segments
and eight PIC switching segments are directly con-
nected together from one PIC to another. The px5 lines
are all broken with CIPs and the PIC pxL and pxH
segments are connected from one block to another
through programmable buffers.
Corner Cell S
p
ecial Functions
In addition to routing functions, special-purpose func-
tions are located in each FPGA corner. The upper-left
PCC contains connections to the boundary-scan logic
and microprocessor interface. The upper-right PCC
contains connections to the readback logic, connectiv-
ity to the global 3-state signal (TS_ALL), and a pro-
grammable clock manager. The lower-left PCC
contains connections to the internal oscillator and a
programmable clock manager. The lower-right PCC
contains connections to the start-up and global reset
logic. These functions are all more completely
described in the Special Function Blocks section of this
data sheet.
5-5821(F)
Figure 29. hIQ Block Detail
IH0[4:0]
IH1[4:0]
IH2[4:0]
IH3[4:0]
IH4[4:0]
FAST CLOC K R
IH5[4:0]
IH6[4:0]
IH7[4:0]
IH8[4:0]
IH9[4:0]
FAST CLOC K L
BL[9:0] vxL[9:0] vx5[9:0] vx1[9:0] SUL[9:0] vx1[9:0] vxH[9:0] BL[9:0]FAST vck
CARRY
Lucent Technologies Inc. 49
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
High-Level Routing Resources (continued)
PIC Interq uad (MID) Routing
There is also connectivity between the PICs in each
quadrant, as well as a clock control (CLKCNTRL) mod-
ule (discussed in the Special Function Blocks section)
between the PIC routing and the interquad routing.
These blocks are called LMID (left), TMID (top), RMID
(right), and BMID (bottom). The TMID routing is shown
in Figure 30. As with the hIQ and vIQ blocks, the only
connectivity to the PIC routing is to the global pxH and
px5 segments.
The pxH segments from the one quadrant can be con-
nected through a CIP to its counterpart in the opposite
quadrant, providing a path that spans the array of
PICs. Since a passive CIP is used to connect the two
pxH segments, a 3-state signal can be routed on the
two pxH segments in the opposite quadrants, and then
connected through this CIP. As with the hIQ and vIQ
bloc ks, CIPs and buff ers allow nibble-wide connections
between the interquad segments, the xH segments,
and the x5 segments.
5-5822(F)
Figure 30. Top (TMID) Routing
EXPRESSCLK RIGHT
PIC LOCAL CLOCKS
PIC LOCAL CLOCKS
pxL[9:0]
pxH[7:0]
px5[9:0]
px1[4:0]
pSW[7:4]
pSW[3:0]
pSW[7:4]
pSW[3:0]
px2[4:0]
1v9xL[4]
1v8xL[3]
Iv7xL[2]
FAST CLOCK
Iv7xL[0]
Iv6xL[3]
Iv6xL[1]
Iv5xL[2]
Iv5xL[0]
Iv4xL[3]
Iv3xL[3]
Iv3xL[1]
Iv2xL[2]
Iv2xL[0]
Iv1xL[3]
Iv1xL[1]
1v0xL[2]
1v0xL[0]
Iv4xL1]
in2[A:D] FROM LEFT
in[A:D] FROM RIGHT
CORNER ExpressCLK
FROM RIGHT
FROM LEFT
EXPRE SSCL K LE FT
SHUTOFF
5050 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Clock Distribution Network
The Series 3 FPGAs provide three types of high-
speed, low-skew clock distributions: system clock, fast
middle clock (fast clock), and ExpressCLK. Because of
the great variety of sources and distribution for clock
signals in the
ORCA
Series 3, the clock mechanisms
will be described here from the inside out. The clock
connections to the PFU will be described, followed by
clock distribution to the PLC array, clock sources to the
PLC array, and finally ending with clock sources and
distribution in the PICs. The ExpressCLK inputs are
new, dedicated cloc k inputs in Series 3 FPGAs. They
are mentioned in several of the clock network descrip-
tions and are described fully later in this section.
PFU Clock Sources
Within a PLC there are five sources for the clock signal
of the latches/FFs in the PFU. Two of the signals are
generated off of the long lines (xL) within the PLC: one
from the set of vertical long lines and one from the set
of horizontal long lines. For each of these signals, any
one of the ten long lines of each set, vertical or horizon-
tal, can generate the clock signal. Two of the five PFU
clock sources come from neighboring PLCs. One clock
is generated from the PLC to the left or right of the cur-
rent PLC, and one is generated from the PLC above or
below the current PLC. The selection decision as to
where these signals come from, above/below and left/
right, is based on the position of the PLC in the array
and has to do with the alternating nature of the source
of the system cloc k spines (discussed later). The last of
the five cloc k sources is also generated within the PLC .
The E1 control signal, described in the PLC Routing
Resources section, can drive the PFU clock. The E1
signal can come from any xBID routing resource in the
PLC. The selection and switching of clock signals in a
PLC is performed in the FINS. Figure 31 shows the
PFU clock sources for a set of four adjacent PLCs.
Global Control Si
g
nals
The four clock signals in each PLC that ar e generated
from the long lines (xL) in the current PLC or an adja-
cent PLC can also be used to drive the PFU clock
enable (CE), local set/reset (LSR) and add/subtract/
write enable (ASWE) signals. The clock signals gener-
ated from vertical long lines can drive CE and ASWE,
and the clocks generated from horizontal long lines can
drive LSR. This allows for low-skew global distribution
of two of these three control signals with the clock rout-
ing while still allowing a global clock route to occur.
5-6054(F)
Figure 31. PFU Clock Sources
PFU
PLC
PFU
PLC
PFU
PLC
PFU
PLC
E1
E1
E1
E1 hxL[9:0]
hxL[9:0]
vxL[9:0]vxL[9:0]
Lucent Technologies Inc. 51
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Clock Distribution Network (continued)
Cloc k Distribution in the PLC Array
S
y
stem Clock
(
SCLK
)
The clock distribution network, or clock spine network,
within the PLC arra y is designed to minimize clock sk ew
while maximizing clock flexibility. Clock flexibility is
expressed in two ways: the ease with which a single
clock is routed to the entire array, and the capability to
provide multiple clocks to the PLC array.
There is one horizontal and one vertical clock spine
passing through each PLC. The horizontal clock spine
is sourced from the PIC in the same row on either the
left- or right-hand side of the arra y, with the source side
(left or right) alternating f or each row. The vertical clock
spines are similarly sourced from the PICs alternating
from the top or bottom of a column. Each clock spine is
capable of driving one of the ten xL routing segments
that run orthogonal to it within each PLC. Full connec-
tivity to all PFUs is maintained due to the connectivity
from the xL lines to the PFU clock signals described in
the previous section; however, only an xL line in every
other row (column) needs to be driven to allow the
given clock signal to be distributed to every PFU.
Figure 32 is a high-le vel diagram of the Series 3 system
clock spine network with sample xL line
connections for a 4 x 4 array of PLCs.
The clock spine structure previously described pro-
vides for complete distrib ution of a clock from any I/O
pin to the entire PLC array by means of a single clock
spine and long lines (xL). This distribution system also
provides a means to have many different clocks routed
to many different and dispersed locations in the PLC
array. Each spine can carry a different clock signal, so
f or the OR3C/T55 (which has an 18 x 18 arra y of PLCs,
implying nine clock spines per side), 36 input clock sig-
nals can be supported using the system clock network.
Fast Clock
Fast clocks are high-speed, low-ske w clock spines that
originate from the CLKCNTRL special function blocks
(described later). There are f our f ast clock spines—one
origin ating on th e middle of each ed ge of the ar ra y. Th e
spines run in the interquad region of the PLC array
from their source side of the device to the last row or
column on the opposite side of the device. The fast
clocks connect to two long lines, xL[8] and xL[9], that
run orthogonal to the spine direction in each PLC.
These long lines can then be connected to the PFU
clock input in the same manner as the general system
clocks, and, like the system clock connections, xL lines
are only needed in every other row (column) to distrib-
ute a clock to every PFU. The limited number of long-
line connections and the low skew of the CLKCNTRL
source combine to make the fast clocks a very robust,
low-skew clock source.
5-5801(F).a
Figure 32.
ORCA
Series 3 System Clock Distribution Overview
(xL)
HORIZONTAL
(xL)
UNUSED
(xL) (xL)
UNUSED
SCLK SPINE (xL)
UNUSED
SCLK SP INE
VERTICAL
SCLK SP INE
SCLK SP INE
SCLK SP INE
UNUSED
SCLK SPINE
UNUSED
SCLK SPINE
UNUSED
SCLK SPINE
UNUSED
SCLK SP INE
UNUSED
SCLK SPINE
5252 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Clock Distribution Network (continued)
Clock Sources to the PLC Array
The source of a clock that is globally available to the
PLC array can be from any user I/O pad, any of the
ExpressCLK pads, or an internally generated source.
S
y
stem Clock
As described in the Programmable Input/Output Cells
section, PICs are grouped in adjacent pairs. Any one of
the eight pads in a PIC pair can driv e a cloc k spine in a
row or column. F or PIC pairs on the top of the chip , the
column associated with the left PIC has the clock
spi ne, for pairs o n the b ottom, the righ t PIC c olumn ha s
the spine. The top PIC of the pair sources the spine
from the left side of the arra y, and the bottom PIC of the
pair sources the spine from the right side of the array.
Clock delay and ske w are minimized by having a single
clock buffer per pair of PICs . The clock spine for each
pair can also be driven by one of the four PIC s witching
segments (pSW) in each PIC of the pair. This allows a
signal generated in the PLC arra y to be routed onto the
global cloc k spine network. The system clock output of
the programmable clock manager (PCM) may also b e
routed to the global system clock spines via the pSW
segments. Figure 33 shows the clock spine multiplex-
ing structure for a pair of PICs on the top of the arra y.
Fast Clock
The fast clock spines are sourced to the PLC array
from each side of the device by the ExpressCLK pads
via the CLKCNTRL function block (described in the
Special Function Blocks section). The ExpressCLK and
fast clock source from the pads is shown in Figure 34
and will be described further in the ExpressCLK Inputs
subsection.
5-5800(F)
Figure 33. PIC System Clock Spine Generation
Clocks in the PICs
Because the Series 3 FPGAs have latches and FFs in
the I/Os, it is necessary to hav e clock signal distribution
to the PIOs as well as in the PLC array. The system
clock, the fast clock, and the ExpressCLK are available
for PIO clocking.
PIC System Clock
There are five local system clock lines in each PIC.
Much li ke the so ur ce s for a c l ock in th e PFU, two of th e
local PIC clocks are generated within the PIC from long
lines. One is generated from the set of ten PIC long
lines (pxL) that runs parallel to the PICs on a side, and
the other is generated from the set of ten long lines (xL)
from the PLC array that terminate in the PIC. Another
local PIC system clock route comes from the set of ten
xL lines in the adjacent PLC that is parallel to the side
of the array on which the PIC resides. The fourth local
PIC system clock route comes from the set of ten long
lines (xL) from the PLC array that terminate in the adja-
cent PIC that is not part of the same PIC pair . Much like
the E1 signals in the PLCs that are used to distribute a
local clock to the PFU source, the fifth local clock line in
each PIC comes from local pSW signals. This clock
signal for each PIC is shown in Figure 33. One of these
five local PIC system clo cks is selected for the system
clock signal in the PIO. It is used as the PIO system
clock for both input and output clocking as selected
within the PIO. All PIOs in a PIC share the same sys-
tem clock.
PIC ExpressCLK
The ExpressCLK signal used at the PIC latches/FFs
comes from the CLKCNTRL function block that resides
in the middle of the side on which the PIC resides. A
single signal comes from the CLKCNTRL and is driven
by separate buffers onto two ExpressCLK long wires.
One of these ExpressCLK signals goes to the PICs on
the right of (above) the CLKCNTRL block, and the
other ExpressCLK signal goes to the PICs on the left of
(below) the CLKCNTRL bl ock on that side.
PAD A
PAD B
PAD C
PAD D
pSW[4]
pSW[5]
pSW[6]
pSW[7]
PAD A
PAD B
PAD C
PAD D
pSW[4]
pSW[5]
pSW[6]
pSW[7]
SPINE
TO LOCA L CLOCKSTO L OCAL CLO CKS
TPICL TPICR
Lucent Technologies Inc. 53
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Clock Distribution Network (continued)
ExpressCLK Inpu ts
There are four dedicated ExpressCLK pads on each
Series 3 device: one in the middle of each side. Two
other user I/O pads can also be used as corner
ExpressCLK inputs, one on the lower-left corner, and
one on the upper-right corner. The corner ExpressCLK
pads feed the ExpressCLK to the two sides of the arra y
that are adjacent to that corner, always driving the
same signal in both directions. The ExpressCLK route
from the middle pad and from the corner pad associ-
ated with that side are multiplexed and can be glitch-
lessly stopped/started under user control using the
StopCLK f e ature of the CLKCNTRL function block
(described under Special Function Blocks) on that side.
The ExpressCLK output of the programmable clock
manager (PCM) is progr ammably connected to the cor-
ner ExpressCLK routes. PCM blocks are found in the
same corners as the corner ExpressCLK signals and
are described in the Special Function Blocks section.
The ExpressCLK structure is shown in Figure 34 (PCM
blocks are not shown).
5-5802(F)
Note: All multiplexers are set durin
g
confi
g
uration.
Figure 34. ExpressCLK and Fast Clock Distribution
Selecting Clock Input Pins
Any user I/O pin on an
ORCA
FPGA can be used as a
fast, low-skew system cloc k input. Since the four dedi-
cated ExpressCLK inputs can only be used to distrib ute
global signals into the FPGA, these pins should be
selected first as clock pins. Within the interquad region
of t he device, t h es e cl ocks sourced b y th e ExpressCLK
inputs are called fast clocks. Choosing the next clock
pin is completely arbitrary, but using a pin that is near
the center of an edge of the device will provide the low-
est skew system clock network. The pin-to-pin timing
numbers in the Timing Ch aracteristics section assume
that the clock pin is in one of the PICs at the center of
any side of the device next to an ExpressCLK pad. For
actual timing characteristics for a given clock pin, use
the timing analyzer results from
ORCA
Foundry.
To select subsequent clock pins, certain rules should
be followed. As discussed in the Programmable Input/
Output Cells section, PICs are grouped into adjacent
pairs. Each of these pairs contains eight I/Os, but only
one of the eight I/Os in a PIC pair can be routed directly
onto a system cloc k spine. Therefore, to achieve top
perf ormance, the ne xt clock input chosen should not be
one of the pins from a PIC pair previously used for a
clock input. If it is necessary to have a second input in
the same PIC pair route onto global system clock rout-
ing, the input can be routed to a free clock spine using
the PIC switching segment (pSW) connections to the
clock spine network at some small sacrifice in speed.
Alternatively, if global distribution of the secondary
clock is not required, the signal can be routed on long
lines (xL) and input to the PFU clock input without
using a clock spine.
Another rule for choosing clock pins has to do with the
alternating nature of clock spine connections to the xL
and pxL routing segments. Starting at the left side of
the device, the first vertical clock spine from the top
connects to hxL[0] (horizontal xL[0]), and the first verti-
cal clock spine from the bottom connects to hxL[5] in all
PLC rows. The next vertical clock spine from the top
connects to hxL[1], and the next one from the bottom
connects to hxL[6]. This progression continues across
the device, and after a spine connects to hxL[9], the
next spine connects to hxL[0] again. Similar connec-
tions are made from horizontal clock spines to vxL (ver-
tical xL) lines from the top to the bottom of the device.
Because the
ORCA
Series 3 clock routing only
requires the use of an xL line in every other row or col-
umn, even two inputs chosen 20 PLCs apart on the
same xL line will not conflict, but it is always better to
avoid thes e choices, if possible. The fast clock spines
in the interquad routing region also connect to xL[8]
and xL[9] for each set of xL lines, so it is better to avoid
user I/Os that connect to xL[8] or xL[9] when a fast
clock is used that might share one of these connec-
tions. Another reason to use the fast clock spines is
that since they use only the xL[9:8] lines, they will not
conflict with internal data buses which typically use
xL[7:0]. For more details on clock selection, refer to
application notes on clock distribution in
ORCA
Series
3 devices.
EXPRES SC LKS TO PIOs
FAST C LO CKS
EXPRES SC LK PADS
CLKCNTRL
BLOCK
5454 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Special Function Blocks
Special function blocks in the Series 3 provide extra
capabilities beyond general FPGA operation. These
blocks reside in the corners and MIDs (middle inter-
quad areas) of the FPGA array.
Single Fu ncti on Blocks
Most of the special function blocks perform a specific
dedicated function. These functions are data/configura-
tion readback control, global 3-state control (TS_ALL),
internal oscillator generation, global set/reset (GSRN),
and start-up logic.
Readback Logic
The readback logic is loca ted in the upper rig ht corner
of the FPGA and can be enabled via a bit stream option
or by instantiation of a library readback component.
Readback is used to read bac k the configuration data
and, optionally, the state of the PFU outputs. A read-
back operation can be done while the FPGA is in nor-
mal system operation. The readback operation cannot
be daisy-chained. To use readback, the user selects
options in the bit stream generator in the
ORCA
Foundry Development System.
Table 12 provides readback options selected in the bit
stream generator tool. The table provides the number
of times that the configuration data can be read back.
This is intended primarily to give the user control over
the security of the FPGA’s configurati on program. The
user can prohibit readback (0), allow a single readback
(1), or allow unrestricted readback (U).
Readback can be performed via the Series 3 micropro-
cessor interface (MPI) or by using dedicated FPGA
readback controls. If the MPI is enabled, readback via
the dedicated FPGA readback logic is disabled. Read-
back using the MPI is discussed in the Microprocessor
Interface (MPI) section.
The pins used for dedicated readback are readback
data (RD_DATA), read configuration (RD_CFG), and
configuration clock (CCLK). A readback operation is ini-
ti ated by a high-to-low transition on RD_CFG. The
RD_CFG input must remain low during the readback
operation. The readback operation can be restarted at
frame 0 by driving the RD_CFG pin high, applying at
least two rising edges of CCLK, and then driving
RD_CFG low again. One bit of data is shifted out on
RD_DATA at the rising edge of CCLK. The first start bit
of the readback frame is transmitted out several cycles
after the first rising edge of CCLK after RD_CFG is input
low (see the Readback Timing Characteristics tab l e in
the Timing Characteristics section). To be certain of the
start of the readback frame, the data can be monitored
for the 01 frame start bit pair.
Readback can be initiated at an address other than
frame 0 via the new microprocessor interface (MPI)
control registers (see the Microprocessor Interf ace
(MPI) section for more information). In all cases, read-
back is performed at sequential addresses from the
start address.
It should be noted that the RD_D ATA output pin is also
used as the dedicated boundary-scan output pin, TDO .
If this pin is being used as TDO, the RD_DATA output
from readback can be routed internally to any other pin
desired. The RD_CFG input pin is also used to control
the global 3-state (TS_ALL) function. Before and during
configuration, the TS_ALL signal is always driven by
the RD_CFG input and readback is disabled. After con-
figuration, the selection as to whether this input drives
the readback or global 3-state function is determined
by a set of bit stream options. If used as the RD_CFG
input for readback, the internal TS_ALL input can be
routed internally to be driven by any input pin.
Table 12. Readback Options
O
p
tion Function
0 Prohibit Readback
1 Allow One Readback Onl
y
U Allow Unrest ricted Number of Readbacks
Lucent Technologies Inc. 55
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Special Function Blocks (continued)
The readback frame contains the configuration data
and the state of the internal logic. During readbac k, the
value of all registered PFU and PIC outputs can be
captured. The following options are allowed when
doing a capture of the PFU outputs.
1. Do not capture data
(
the data written to the RAMs,
usuall
y
0, will be read back
)
.
2. Capture data upon enterin
g
readback.
3. Capture data based upon a confi
g
urable si
g
nal
internal to the FPGA. If this si
g
nal is tied to
lo
g
ic 0, capture RAMs are written continuousl
y
.
4. Capture data on either options 2 or 3 above.
The readback frame has an identical format to that of
the configuration data frame, which is discussed later in
the Configuration Data Format section. If LUT memory
is not used as RAM and there is no data capture, the
readback data (not just the format) will be identical to
the configuration data for the same frame. This eases a
bitwise comparison between the configuration and
readback data. The configuration header, including the
length count field, is not part of the readback frame.
The readbac k frame contains bits in locations not used
in the configuration. These locations need to be
masked out when comparing the configuration and
readback frames. The development system optionally
provides a readback bit stream to compare to readbac k
data from the FPGA. Also note that if any of the LUTs
are used as RAM and new data is written to them,
these bits w ill not have the same values as the original
configuration data frame either.
Global 3-State Control (TS_ALL)
To increase the testability of the
ORCA
Series FP G As,
the global 3-state function (TS_ALL) disables the
device. The TS_ALL signal is driven from either an
external pin or an internal signal. Before and during
configuration, the TS_ALL signal is driven by the input
pad RD_CFG. After configuration, the TS_ALL signal
can be disabled, driven from the RD_CFG input pad, or
driv en b y a general routing signal in the upper right cor-
ner. Before configuration, TS_ALL is active-low; after
configuration, the sense of TS_ALL can be inverted.
The following occur when TS_ALL is activated:
1. All of the user I/O output buffers are 3-stated, the
user I/O input buffers are pulled up
(
with the pull-
down disabled
)
, and the input buffers are confi
g
ured
with TTL input thresholds
(
OR3Cxx onl
y)
.
2. The TDO/RD_DATA output buffer is 3-stated.
3. The RD_CFG, RESET, and PRGM input buffers remain
active with a pull-up.
4. The DONE output buffer is 3-stated, and the input
buffer is pulled up.
Internal Oscillator
The internal oscillator resides in the lower left corner of
the FPGA array. It has output clock frequencies of
1.25 MHz and 10 MHz. The internal oscillator is the
source of the internal CCLK used for configuration. It
may also be used after configuration as a general-
purpose clock signal.
Global Set/Reset (GSRN)
The GSRN logic resides in the lower right corner of the
FPGA. GSRN is an inv ertible , def ault, active-lo w signal
that is used to reset all of the user-accessible latches/
FFs on the device. GSRN is automatically asserted at
powerup and during configuration of the device.
The timing of the release of GSRN at the end of config-
uration can be programmed in the start-up logic
described below. Following configuration, GSRN may
be connected to the RESET pin via dedicated routing, or
it may be connected to any signal via normal routing.
Within each PFU and PIO, individual FFs and latches
can be programmed to either be set or reset when
GSRN is asserted. A new option in Series 3 allows indi-
vidual PFUs and PIOs to turn off the GSRN signal to its
latches/FFs after configuration.
The RESET input pad has a special relationship to
GSRN. During configuration, the RESET input pad
always initiates a configuration abort, as described in
the FPGA States of Operation section. After configura-
tion, the global set/reset signal (GSRN) can either be
disabled (the default), directly connected to the RESET
input pad, or sourced by a lower-right corner signal. If
the RESET input pad is not used as a global reset after
configuration, this pad can be used as a normal input
pad.
5656 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Special Function Blocks (continued)
Start-Up Logic
The start-up logic bloc k is located in the lower right cor-
ner of the FPGA. This block can be configured to coor-
dinate the relative timing of the release of GSRN, the
activation of all user I/Os, and the assertion of the
DONE signal at the end of configuration. If a start-up
clock is used to time these events, the start-up clock
can come from CCLK, or it can be routed into the start-
up block using lower right corner routing resources.
These signals are described in the Start-Up subsection
of the FPGA States of Operation section.
Clock Control (CLKCNTRL) and StopCLK
There is one CLKCNTRL block in the MID section of
the interquad routing on each side of the FPGA. This
block is used to selectively distribute the fast clock to
the PLC array and the left (top) and right (bottom)
ExpressCLKs (ECKL and ECKR) to the side of the
array on which the CLKCNTRL block resides.
The source clock for the CLKCNTRL block comes
either from the ExpressCLK pad at the middle of the
side of the FPGA or from the corner ExpressCLK route
that comes from the corner ExpressCLK pad (at the
lower left or upper right of the device, whichever is
closer). The programmable clock manager ExpressCLK
output can also be sourced to this corner routing for
distribution at the two closest CLKCNTRL blocks.
Each CLKCNTRL block also features an invertible
StopCLK shutoff input that is available from local rout-
ing. This feature ma y be used to glitchlessly stop and
start the clock at the three outputs of each CLKCNTRL
bloc k and has the option of doing so on either the rising
or falling edge of the clock. When the clock is halted
based on its rising edge, it stops and stays at VDD.
When it is stopped based on its falling edge, it stops
and stays at GND. If the StopCLK shutoff signal meets
the CLKCNTRL setup and hold times, the clock is
stopped on the second clock cycle after the shutoff sig-
nal. A diagram of the bottom CLKCNTRL block and
StopCLK timing is shown in Figure 35.
5-5981(F)
Notes:
CLKCNTRL output clocks are ExpressCLK left and right and fast clock.
Clock shutoff shown active-high acting on clock falling edge.
Figure 35. Top CLKCNTRL Function Block
CORNER EXPRES SCLK
CLOCK SHUTOFF
EXPRESSCLK RIGHTEXPRESSCLK LEFT
FAST CLOCK
CLOCK SHUTOFF
OFF_SET OFF_HLD
OFF_SET
OFF_HLD
CLKCNTRL OU TP UT
CLOCKS
Lucent Technologies Inc. 57
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Special Function Blocks (continued)
Boundary Scan
The increasing complexity of integrated circuits (ICs)
and IC packages has increased the difficulty of testing
printed-circuit boards (PCBs). To address this testing
problem, the
IEEE
standard 1149.1/D1 (
IEEE
Standard
Test Access Port and Boundary-Scan Architecture) is
implemented in the
ORCA
series of FPGAs. It allows
users to efficiently test the interconnection between
integrated circuits on a PCB as well as test the inte-
grated circuit itself. The
IEEE
1149.1/D1 standard is a
well-defined protocol that ensures interoperability
among boun dary -sc an (B SCA N) equip ped devices
from different vendors.
The
IEEE
1149.1/D1 standard defines a test access
port (TAP) that consists of a four-pin interface with an
optional reset pin for boundary-scan testing of inte-
grated circuits in a system. The
ORCA
Series FPGA
provides four interface pins: test data in (TDI), test
mode select (TMS), test clock (TCK), and test data out
(TDO). The PRGM pin used to reconfigure the device
also rese ts the boun dary-sc an log ic.
The user test host serially loads test commands and
test data into the FPGA through these pins to drive out-
puts and examine inputs. In the configuration shown in
Figure 36, where boundary scan is used to test ICs,
test data is transmitted serially into TDI of the first
BSCAN device (U1), through TDO/TDI connections
between BSCAN de vices (U2 and U3), and out TDO of
the last BSCAN device (U4). In this configuration, the
TMS and TCK signals are routed to all boundary-scan
ICs in parallel so that all boundary-scan components
operate in the same state. In other configurations, mul-
tipl e scan paths a re used in stead of a single ring. When
multiple scan paths are used, each ring is indepen-
dently controlled by its own TMS and TCK signals.
Figure 37 provides a system interface f or components
used in the boundary-scan testing of PCBs. The three
major components shown are the test host, boundary-
scan support circuit, and the devices under test
(DUTs). The DUTs shown here are
ORCA
Series
FPGAs with dedicated boundary-scan circuitry. The
test host is normally one of the follo wing: automatic test
equipment (ATE), a workstation, a PC, or a micropro-
cessor.
5-5972(F)
Key: BS C = boundary-scan cell, BDC = bidirectional data cell,
and DCC = data control cell.
Figure 36. Printed-Circuit Board with Boundary-
Scan Circuitry
TDI
TMS
TCK
TDO
TDI
TDO
TMS
TCK
U2
net a
net b
net c
PLC
ARRAY BDC
BSC
p_in
p_ts
SCAN
OUT
SCAN
IN
PR[ij]
DCC
p_out
BDC
BSC
p_in
p_out
p_ts
PL[ij]
DCC
SCAN
IN
SCAN
OUT
BDCDCC
BSC
p_in
p_out
p_ts
SCAN
OUT
PB[ij]
SCAN
IN
TDO TCK TMS TDI
TAPC
BYPASS
REGISTER
INSTRUCTION
REGISTER
BDC DCC
BSC
p_inp_out p_ts
SCAN
OUT
SCAN
IN
PT[ij]
SEE ENLARGED VIEW BELOW
s
TDI
TDO
TMS
TCK
U3
TDI
TDO
TMS
TCK
U4
TDI
TDO
TMS
TCK
U2
58 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Special Function Blocks (continued)
5-6765(F)
Figure 37. Boundary-Scan Interface
D[7:0]
INTR
MICRO-
PROCESSOR
D[7:0]
CE
RA
R/W
DAV
INT
SP
TMS0
TCK
TDI
TDO TDI
TMS
TCK
TDO
ORCA
SERIES
FPGA
TDI
ORCA
SERIES
FPGA
TMS
TCK
TDO
TDI
TMS
TCK
TDO
ORCA
SERIES
FPGA
LUCENT
BOUNDARY-
SCAN
MASTER
(BSM)
(DUT) (DUT)
(DUT)
The boundary-scan support circuit shown in Figure 37
is the 497AA Boundary-Scan Master (BSM). The BSM
off-loads tasks from the test host to increase test
throughput. To interface between the test host and the
DUTs, the BSM has a general microprocessor interf ace
and provides parallel-to-serial/serial-to-parallel conver-
sion, as well as three 8K data buffers. The BSM also
increases test throughput with a dedicated automatic
test-pattern generator and with compression of the test
response with a signature analysis register. The PC-
based boundary-scan test card/software allows a user
to quickly prototype a boundary-scan test setup.
Boundary-Scan Instructions
The
ORCA
Series boundary-scan circuitry is used for
three mandatory
IEEE
1149.1/D1 tests (EXTEST,
SAMPLE/PRELOAD, BYPASS), the optional
IEEE
1149.1/D1 IDCODE instruction, and five
ORCA
-defined
instructions. The 3-bit wide instruction register sup-
ports the nine instructions listed in Table 13, where the
use of PSR1 or USERCODE is selectable b y a bit
stream option.
Table 13. Boundary-Scan Instructions
Code Instruction
000 EXTEST
001 PLC Scan Rin
g
1
(
PSR1
)
/USERCODE
010 RAM Write
(
RAM_W
)
011 IDCODE
100 SAMPLE/PRELOAD
101 PLC Scan Rin
g
2
(
PSR2
)
110 RAM Read
(
RAM_R
)
111 BYPASS
Lucent Technologies Inc. 59
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Special Function Blocks (continued)
The external test (EXTEST) instruction allows the inter-
connections between ICs in a system to be tested f or
opens and stuck-at faults. If an EXTEST instruction is
performed for the system shown in Figure 36, the con-
nections between U1 and U2 (shown by nets a, b, and
c) can be tested by driving a value onto the given nets
from one device and then determi ni ng wheth er the
same value is seen at the other device. This is deter-
mined by shifting 2 bits of data for each pin (one f or the
output value and one for the 3-state value) through the
BSR until each one aligns to the appropriate pin. Then,
based upon the value of the 3-state signal, either the
I/O pad is driven to the value given in the BSR, or the
BSR is updated with the input value from the I/O pad,
which allows it to be shifted out TDO.
The SAMPLE/PRELOAD instruction is useful for sys-
tem debugging and fault diagnosis by allowing the data
at the FPGA’s I/Os to be observed during normal
operation or written during test operation. The data for
all of the I/Os is captured simultaneously into the BSR,
allowing them to be shifted-out TDO to the test host.
Since each I/O buffer in the PICs is bidirectional, two
pieces of data are captured for each I/O pad: the v alue
at the I/O pad and the value of the 3-state control sig-
nal. For preload operation, data is written from the BSR
to all of the I/Os simultaneously.
There are five
ORCA
-defined instructions. The PLC
scan rings 1 and 2 (PSR1, PSR2) allow user-defined
internal scan paths using the PLC latches/FFs. The
RAM_Write Enable (RAM_W) instruction allows the
user to serially configure the FPGA through TDI. The
RAM_Read Enable (RAM_R) allows the user to read
back RAM contents on TDO after configuration. The
IDCODE instruction allows the user to capture a 32-bit
identification code that is unique to each device and
serially output it at TDO . The IDCODE format is shown
in Table 14.
Table 14. Boundar
y
-Scan ID Code
* PLC array size of FPGA, reverse bit order.
Note: Table assumes version 0.
Device Version
(
4 bits
)
Part*
(
10 bits
)
Famil
y
(
6 bits
)
Manufacturer
(
11 bits
)
LSB
(
1 bit
)
OR3T20 0000 0011000000 110000 00000011101 1
OR3T30 0000 0111000000 110000 00000011101 1
OR3C/T55 0000 0100100000 110000 00000011101 1
OR3C/T80 0000 0110100000 110000 00000011101 1
OR3T125 0000 0011100000 110000 00000011101 1
OR3T165 0000 0000010000 110000 00000011101 1
6060 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Special Function Blocks (continued)
ORCA
Boundary-Scan Circuitry
The
ORCA
Series boundary-scan circuitry includes a
test access port controller (TAPC), instruction register
(IR), boundary-scan register (BSR), and bypass regis-
ter. It also includes circuitry to support the four pre-
defined instructions.
Figure 38 shows a functional diagram of the boundary-
scan circuitry that is implemented in the
ORCA
Series.
The input pins’ (TMS, TCK, and TDI) locations vary
depending on the part, and the output pin is the dedi-
cated TDO/RD_DATA output pad. Test data in (TDI) is
the serial input data. Test mode select (TMS) controls
the boundary-scan test access port controller (TAPC).
Test clock (TCK) is the test clock on the board.
The BSR is a series connection of boundary-scan cells
(BSCs) around the periphery of the IC. Each I/O pad on
the FPGA, except for CCLK, DONE, and the boundary-
scan pins (TCK, TDI, TMS, and TDO), is included in
the BSR. The first BSC in the BSR (connected to TDI)
is located in the first PIC I/O pad on the left of the top
side of the FPGA (PTA PIC). The BSR proceeds cloc k-
wise around the top, right, bottom, and left sides of the
array. The last BSC in the BSR (connected to TDO) is
located on the top of the left side of the array (PL1D).
The bypass instruction uses a single FF, which resyn-
chroniz es test data that is not part of the current scan
operation. In a bypass instruction, test data receiv ed on
TDI is shifted out of the bypass register to TDO. Since
the BSR (which requires a two FF delay for each pad)
is bypassed, test throughput is increased when devices
that are not part of a test operation are bypassed.
The boundary-scan logic is enabled before and during
configuration. After configuration, a configuration
option determines whether or not boundary-scan logic
is used.
The 32-bit boundary-scan identification register con-
tains the manufacturer’s ID number, unique part num-
ber, and version (as described earlier). The
identification register is the def ault source for data on
TDO after RESET if the TAP controller selects the shift-
data-register (SHIFT-DR) instruction. If boundary scan
is not used, TMS, TDI, and TCK become user I/Os,
and TDO is 3-stated or used in the readback operation.
An optional USERCODE is available if the boundary-
scan PSR1 instruction is not used. The selection
between PSR1 and USERCODE is a configuration
option and can be performed in
ORCA
Foundry. The
USERCODE is an 11-bit value that the user can set
during device configuration and can be written to and
read from the FPGA via the boundary-scan logic. The
USERCODE value replaces the manufacturer field of
the boundary-scan ID code when the USERCODE
instruction is issued, allowing users to have confi gured
devices identified in a user-defined manner. The manu-
facturer ID field remains available when the IDCODE
instruction is issued.
5-5768(F)
Figure 38.
ORCA
Series Boundary-Scan Circuitry Functional Diagram
TAP
CONTROLLER
TMS
TCK
BOUNDA RY -SCAN REGISTER
PSR2 REGISTER (PLCs)
BYPASS REGISTER
DATA
MUX
INSTRUC TIO N DE CODER
INSTRUCT ION RE G IST E R
M
U
X
RESET
CLOCK IR
SHIFT-IR
UPDATE-IR
PUR
TDO
SELECT
ENABLE
RESET
CLOCK DR
SHIFT-DR
UPDATE-DR
TDI
DATA RE G IST E RS
PSR1 REGISTER (PLCs)
CONFIGURATION REGISTER
(RAM_R, RAM_W)
PRGM
I/O BUFFER S
V
DD
V
DD
V
DD
V
DD
IDCODE RE G IST E R
Lucent Technologies Inc. 61
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Special Function Blocks (continued)
ORCA
Series TAP Controller (TAPC)
The
ORCA
Series TAP controller (TAPC) is a 1149.1/
D1 compatible test access port controller . The 16 JTAG
state assignments from the
IEEE
1149.1/D1 specifica-
tion are used. The TAPC is controlled by TCK and
TMS. The TAPC states are used for loading the IR to
allow three basic functions in testing: providing test
stimuli (Update-DR), test e xecution (Run-Test/Idle),
and obtaining test responses (Capture-DR). The TAPC
allows the test host to shift in and out both instructions
and test data/results. The inputs and outputs of the
TAPC are provided in the table below. The outputs are
primarily the control signals to the instruction register
and the data register.
Table 15. TAP Controller In
p
ut/Out
p
uts
The TAPC generates control signals that allow capture,
shift, and update operations on the instruction and data
registers. In the capture operation, data is loaded into
the register. In the shift operation, the captured data is
shifted out while new data is shifted in. In the update
operation, either the instruction register is loaded for
instruction decode, or the boundary-scan register is
updated for control of outputs.
The test host generates a test by providing input into
the
ORCA
Series TMS input synchronous with TCK.
This sequences the TAPC through states in order to
perform the desired function on the instruction register
or a data register. Figure 39 provides a diagram of the
state transitions for the TAPC. The next state is deter-
mined by the TMS input value.
5-5370(F)
Figure 39. TAP Controller State Transition Diagram
S
y
mbol I/O Function
TMS I Test Mode Select
TCK I Test Clock
PUR I Powerup Reset
PRGM I BSCAN Reset
TRESET O Test Lo
g
ic Reset
Select O Select IR
(
Hi
g
h
)
; Select-DR
(
Low
)
Enable O Test Data Out Enable
Capture-DR O Capture/Parallel Load-DR
Capture-IR O Capture/Parallel Load-IR
Shift-DR O Shift Data Re
g
ister
Shift-IR O Shift Instruction Re
g
ister
Update-DR O Update/Parallel Load-DR
Update-IR O Update/Parallel Load-IR
SELECT-
DR-SCAN
CAPTURE-DR
SHIFT-DR
EXIT1-DR
PAUSE-DR
EXIT2-DR
UPDATE-DR
1
1
0
0
10
RUN-TEST/
IDLE 1
TEST-LOGIC-
RESET
SELECT-
IR-SCAN
CAPTURE-IR
SHIFT-IR
EXIT1-IR
PAUSE-IR
EXIT2-IR
UPDATE-IR
1
1
0
10
00
0
0
1
0
1
1
1
0
1
1
0
0
0
0
1
11
0
6262 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Special Function Blocks (continued)
Boundary-Scan Cells
Figure 40 is a diagram of the boundary-scan cell (BSC)
in the
ORCA
series PICs. There are four BSCs in each
PIC: one for each pad, except as noted above. The
BSCs are connected serially to f orm the BSR. The
BSC controls the functionality of the in, out, and 3-state
signals for each pad.
The BSC allows the I/O to function in either the normal
or test mode. Normal mode is defined as when an out-
put buffer receives input from the PLC array and pro-
vides output at the pad or when an input buffer
provides input from the pad to the PLC arra y. In the test
mode, the BSC executes a boundary-scan operation,
such as shifting in scan data from an upstream BSC in
the BSR, providing test stimuli to the pad, capturing
test data at the pad, etc.
The primary functions of the BSC are shifting scan data
serially in the BSR and observing input (p_in), output
(p_out), and 3-state (p_ts) signals at the pads. The
BSC consists of two circuits: the bidirectional data cell
is used to access the input and output data, and the
direction control cell is used to access the 3-state
value. Both cells consist of a flip-flop used to shift scan
data which f eeds a flip-flop to control the I/O buff er . The
bidirectional data cell is connected serially to the direc-
tion control cell to form a b oundary-scan shift register.
The TAPC signals (capture, update, shiftn, treset, and
TCK) and the MODE signal control the operation of the
BSC. The bidirectional data cell is also controlled by
the high out/low in (HOLI) signal generated by the
direction control cell. When HOLI is low, the bidirec-
tional data cell receives input buffer data into the BSC.
When HOLI is high, the BSC is loaded with functional
data from the PLC.
The MODE signal is generated from the decode of the
instruction register. When the MODE signal is high
(EXTEST), the scan data is propagated to the output
buffer. When the MODE signal is low (BYPASS or
SAMPLE), functional data from the FPGA’s internal
logic is propagated to the output buffer.
The boundary-scan description language (BSDL) is
provided for each device in the
ORCA
Series of FPGAs
on the
ORCA
Foundry CD. The BSDL is generated
from a device profile, pinout, and other boundary-scan
information.
5-2844(F
Figure 40. Boundary-Scan Cell
DQDQ
DQDQ
SCAN IN
p_out
HOLI
BIDIRECTIONAL DATA CELL
I/O BUFFER
DIRECTION CONTROL CELL
MODEUPDATE/TCKSCAN OUTTCKSHIFTN/CAPTURE
p_ts
p_in PAD_IN
PAD_TS
PAD_OUT
0
1
0
1
0
1
0
1
0
1
Lucent Technologies Inc. 63
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Special Function Blocks (continued)
Boundary-Scan Timing
To ensure race-free operation, data changes on specific clock edges. The TMS and TDI inputs are clocked in on
the rising edge of TCK, while changes on TDO occur on the falling edge of TCK. In the execution of an EXTEST
instruction, parallel data is output from the BSR to the FPGA pads on the falling edge of TCK. The maximum fre-
quency allowed for TCK is 10 MHz.
Figure 41 shows timing waveforms for an instruction scan operation. The diagram shows the use of TMS to
sequence the TAPC through states. The test host (or BSM) changes data on the falling edge of TCK, and it is
clocked into the DUT on the rising edge.
5-5971(F)
Figure 41. Instruction Register Scan Timing Diagram
TCK
TMS
TDI
RUN-TEST/IDLE
RUN-TEST/IDLE
EXIT1-IR
EXIT2-IR
UPDATE-IR
SELECT-DR-SCAN
CAPTURE-IR
SELECT-IR-SCAN
TEST-LOGIC-RESET
SHIFT-IR
PAUSE-IR
SHIFT-IR
EXIT1-IR
6464 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Microprocessor Interface (MPI)
The Series 3 FPGAs have a dedicated synchronous
microprocessor interface function block (see
Figure 42). The MPI is programmable to operate with
PowerPC
MPC800 series microprocessors and
Intel
*
i960
* J core processors; see Table 16 and Table 17,
respectively, for compatible processors. The MPI imple-
ments an 8-bit interface to the host processor (
Pow-
erPC
or
i960
) that can be used for configuration and
readback of the FPGA as well as for user-defined data
processi ng and general mon ito r in g of FPGA func tion.
In addition to dedicated-function registers, the micro-
processor interface allows for the control of up to 16
user registers (RAM or flip-flops) in the FPGA logic. A
synchronous/asynchronous handshake procedure is
used to control transactions with user logic in the FPGA
array. There is also capability for the FPGA logic to
interrupt the host processor either by a hard interrupt or
by having the host processor poll the microprocessor
interface.
The control portion of the microprocessor interface is
available following powerup of the FPGA if the mode
pins specify MPI mode, e v en if the FPGA is not yet con-
figured. The mode pin (M[2:0]) settings can be found in
the FPGA Configuration Modes section of this data
sheet, and the setup and use of the MPI for configura-
tion is discussed in the MPI Setup and Control subsec-
tion. For postconfiguration use, the MPI must be
included in the configuration bit stream by using an MPI
library element in your design from the
ORCA
macro
library, or by setting the MP_USER bit of the MPI con-
figuration control register prior to the start of configura-
tion (MPI registers are discussed later).
*
Intel
and
i960
are registered trademarks of Intel Corporation.
5-5806(F)
Figure 42. MPI Block Diagram
DONE
RD_DATA
INIT
D7 D7IN
D7OUT
D6 D6IN
D6OUT
D5 D5IN
D5OUT
D4 D4IN
D4OUT
D3 D3IN
D3OUT
D2 D2IN
D2OUT
D1 D1IN
D1OUT
D0 D0IN
D0OUT
ORCA
3C/Txxx MPI
STATUS
REGISTER
SCRATCHPAD
REGISTER
READBACK
DATA REGISTER
READBACK
ADDR REGISTER
CONTROL
REGISTERS
PART ID
REGISTERS
RESET
RD_CFG
PRGM
GSR
IRQ TO GSR BLOCK
TO FPGA
ROUTING
USER_START
USER_END
WR_CTRL
A[3:0]
RDYRCV
CLK
ADS
ALE
W/R
i960
LOGIC
RD/WR
BT
TS
CLKOUT
TA
POWERPC
LOGIC
DECODE/CONTROL
POWERPC
ONLY
A4
A3
A2
A1
A0
RD
CS0
CS1
CCLK
M3
M2
M1
M0
MPI_IRQ
MPI_ACK
MPI_CLK
MPI_STRB
MPI_ALE
MPI_RW
MPI_B1
TO FPG A
ROUTING
D[7:0]IN
D[7:0]OUT
DEVICE PAD
I/O BU FF E R
Lucent Technologies Inc. 65
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Microprocessor Interface (MPI) (continued)
PowerPC
System
In Figure 43, the
ORCA
FPGA is a memory-mapped
peripheral to the
PowerPC
processor. The
PowerPC
interface uses separate address and data buses and
has several control lines. The
ORCA
chip select lines,
CS0 and CS1, are each connected to an address line
coming from the
PowerPC
. In this manner, the FPGA is
capable of a transaction with the
PowerPC
whenever
the address line connected to CS0 is low, the address
line for CS1 is high, and there is a v alid address on
PowerPC
address lines A[27:31]. Other forms of selec-
tion are possible by using the FPGA chip selects in a
diff erent way. For example,
PowerPC
address bits
A[0:26] could be decoded to select CS0 and CS1, or if
the FPGA is the only peripheral to the
PowerPC
, CS0
and CS1 could be tied low and high, respectively, to
cause them to always be selected. If the MPI is not
used for FPGA configuration, decoding logic can be
implemented internal or e xternal to the FPGA. If logic
internal to the FPGA is used, the chip selects must be
routed out on an output pin and then connected exter-
nally to CS0 and/or CS1. If the MPI is to be used for
configuration, any decode logic used must be imple-
mented external to the FPGA since the FPGA logic has
not been configured yet.
5-5761(F)
Note: FPGA shown as a memor
y
-mapped peripheral usin
g
CS0 and
CS1. Other decodin
g
schemes are possible usin
g
CS0 and/or
CS1.
Figure 43.
PowerPC
/MPI
The basic flow of a transaction on the
PowerPC
/MPI
interface is given below. Pin descriptions are shown in
Table 16 and timing is sho wn in the Timing Characteris-
tics section of this data sheet. For both read and write
transactions, the address, chip select, and read/write
(read high, write low) signals are set up at the FPGA
pins by the
PowerPC
. The
PowerPC
then asserts its
transfer start signal (TS) low. Data is available to the
MPI during a write at the rising clock edge after the
clock cycle during which TS is low. The transfer is
acknowledged to the
PowerPC
by the low assertion of
the TA signa l. The MPI
PowerPC
interface does not
support burst transf ers, so the burst inhibit signal, BI, is
also asserted low during the transfer acknowledge. The
same process applies to a read from the MPI except
that the read data is e xpected at the FPGA data pins by
the
PowerPC
at the rising edge of the clock when TA is
low. The MPI only drives TA low for one clock cycle.
Interrupt requests can be sent to the
PowerPC
asyn-
chronously to the read/write process. Interrupt requests
are so urced b y the u ser-logi c in the FP GA. The MPI will
assert the request to the
PowerPC
as a direct interrupt
signal and /or a pollable bit in the MPI status register
(discussed in the MPI Setup and Control section). The
MPI will continue to assert the interrupt request until
the user-logic deasserts its interrupt request signal.
Table 16.
PowerPC
/MPI Configuration
DOUT
CCLK
D[7:0]
A[4:0]
MPI_CLK
MPI_RW
MPI_ACK
MPI_BI
MPI_IRQ
MPI_STRB
CS0
CS1 HDC
LDC
D[7:0]
A[27:31]
CLKOUT
RD/WR
TA
BI
IRQx
TS
A26
A25
TO DAISY-
CHAINED
DEVICES
POWERPC ORCA
8
FPGA
SERIES 3
DONE
INIT
PowerPC
Signal
ORCA
Pin
Name MPI
I/O Function
D
[
0:7
]
D
[
7:0
]
I/O 8-bit data bus
A
[
27:31
]
A
[
4:0
]
I5-bit MPI address
bus
TS RD/MPI_STRB I Transfer start si
g
nal
—CS0 IActive-low MPI
select
— CS1 I Active-hi
g
h MPI
select
CLKOUT A7/MPI_CLK I
PowerPC
interface
clock
RD/WR A8/MPI_RW I Read
(
hi
g
h
)
/write
(
low
)
si
g
nal
TA A9/MPI_ACK O Active-low transfer
acknowled
g
e si
g
nal
BI A10/MPI_BI O A ctive-low bur st
transfer inh ibi t
si
g
nal
An
y
of
IRQ
[
7:0
]
A11/MPI_IRQ O Active-low interrupt
re
q
uest si
g
nal
6666 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Micropr ocessor Interface (MPI) (continued)
i960
System
Figure 44 shows a schematic for connecting the
ORCA
MPI to supported
i960
processors. In the figure, the
FPGA is shown as the only peripheral, with the FPGA
chip select lines, CS0 and CS1, tied low and high,
respectively. The
i960
address and data are multi-
ple xed onto the same bus. This precludes memory
mapping of the FPGA in the
i960
memory space of a
multiperipheral system without some form of address
latching to capture and hold the address signals to
drive the CS0 and/or CS1 signals. Multiple address sig-
nals could also be decoded and latched to drive the
CS0 and/or CS1 signals. If the MPI is not used for
FPGA configuration, decoding/latching logic can be
implemented internal or e xternal to the FPGA. If logic
internal to the FPGA is used, the chip selects must be
routed out an output pin and then connected e xternally
to CS0 and/or CS1. If the MPI is to be used for configu-
ration, any decode/latch logic used must be imple-
mented external to the FPGA since the FPGA logic has
not been configured yet.
5-5762
(
F
)
Note: FPGA shown as onl
y
s
y
stem peripheral with fixed-chip select
si
g
nals. For multiperipheral s
y
stems, address decodin
g
and/
or latchin
g
can be used to implement chip selects.
Figure 44.
i960
/MPI
The basic flow of a transaction on the
i960
/MPI inter-
face is given below. Pin descriptions are shown in
Table 17, and timing is shown in the
ORCA
Timing
Characteristics section of this data sheet. F or both read
and write transactions, the address latch enable (ALE)
is set up by the
i960
at the FPGA to the falling edge of
the clock. The address, b yte enables , chip selects, and
read/write (read low, write high) signals are normally
set up at the FPGA pins by the
i960
at the next rising
edge of the clock. At this same rising clock edge, the
i960
asserts its address/data strobe (ADS) low. Data is
available to the MPI during a write at the rising clock
edge of the following clock cycle. The transfer is
acknowledged to the
i960
by the low assertion of the
ready/ recover (RDYRCV) signal. The same process
applies to a read from the MPI except that the read
data is expected at the FPGA data pins by the
i960
at
the rising edge of the clock when RDYRCV is low. The
MPI only drives RDYRCV low for one clock cycle.
Interrupts can be sent to the
i960
asynchronously to
the read/write process. Interrupt requests are sourced
by the user-logic in the FPGA. The MPI will assert the
request to the
i960
as a direct interrupt signal and/or a
pollable bit in the MPI status register (discussed in the
MPI Setup and Control section). The MPI will continue
to assert the interrupt request until the user-logic deas-
serts its interrupt request signal.
Table 17.
i960
/MPI Confi
g
uration
DOUT
CCLK
D[7:0]
MPI_CLK
MPI_RW
MPI_ACK
MPI_IRQ
MPI_ALE
MPI_BE1
HDC
LDC
TO DAISY-
CHAINED
DEVICES
ORCA
8
FPGA
SERIES 3
DONE
INIT
AD[7:0]
CLKIN
W/R
RDYRCV
XINTx
ALE
BE1
i960
CS1
CS0
i960
SYSTEM CLOCK
VDD
MPI_BE0
BE0 MPI_STRB
ADS
i960
Si
g
nal
ORCA
Pin
Name MPI
I/O Function
AD
[
7:0
]
D
[
7:0
]
I/O Multiplexed 5-bi t address/
8-bit data bus. The
address a ppe ars on D
[
4:0
]
.
ALE RDY/RCLK/
MPI_ALE I Address latch enable used
to capture address from
AD
[
4:0
]
on fallin
g
ed
g
e of
clock.
ADS RD/
MPI_STRB I Address/d ata stro be to
indicate start of transac-
tion.
—CS0 I Active-low MPI select.
— CS1 I Active-hi
g
h MPI select .
S
y
stem
Clock A7/
MPI_CLK I
i960
s
y
stem clock. This
clock is sourced b
y
the
s
y
stem and not the
i960
.
W/RA8/MPI_RW I Write
(
hi
g
h
)
/read
(
low
)
si
g
nal.
RDYRCV A9/
MPI_ACK O Active-low read
y
/recover
si
g
nal indicatin
g
acknowl-
ed
g
ment of the transac-
tion.
An
y
of
XINT
[
7:0
]
A11/
MPI_IRQ O Active-low interrupt
re
q
uest si
g
nal.
BE0 A0/
MPI_BE0 IB
y
te-enable 0 used as
address bit 0 in
i960
8-bit
mode.
BE1 A1/
MPI_BE1 IB
y
te-enable 1 used as
address bit 1 in
i960
8-bit
mode.
Lucent Technologies Inc. 67
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Micropr ocessor Interface (MPI) (c onti nu ed)
MPI Interface to FPGA
The MPI interfaces to the user-programmable FPGA
logic using a 4-bit address, read/write control signal,
interrupt request signal, and user start and user end
handshake signals. Timing numbers are provided so
that the user-logic data transfers can be performed syn-
chronously with t he host processor (
PowerPC
or
i960
)
interface clock or asynchronously. Table 18 shows the
internal interf ace signals between the MPI and the
FPGA user-programmable logic. All of the signals are
connected to the MPI in the upper-left corner of the
de vice e xcept f or the D[7:0] and CLK signals that come
directly from the I/O pin.
The 4-bit addressing from the MPI to the PLCs allows
for up to 16 locations to be addressed by the host pro-
cessor. The user address space of the MPI does not
address any hard register. Rather, the user is free to
construct registers from FFs, latches, or RAM that can
be selected by the addressing. Alternately, the decoded
address signals may be used as control signals for
other functions such as state machines or timers.
The transaction sequence between the MPI and the
user-logic is as follows. When the host processor ini-
tiates a transaction as discussed in the preceding sec-
tions, the MPI outputs the 4-bit user address (UA[3:0])
and the read/write control signal (URDWR, which is
read-high, write-low regardless of host processor), and
then asserts the user start signal, USTART. During a
write from the host processor , the user logic can accept
data written by the host processor from the D[7:0] pins
once the USTART signal is asserted. The user logic
ends a transaction by asserting an active-high user
end (UEND) signal to the MPI.
The MPI will insert wait-states in the host processor
bus cycles, holding the host processor until the user-
logic completes its task and returns a UEND signal,
upon which the MPI generates an acknowledge signal.
If the host processor is reading from the FPGA, the
user logic must have the read data available on the
D[7:0] pins of the FPGA when the UEND signal is
asserted. If the user logic is fast or if the MPI user
address is being decoded for use as a control signal,
the MPI transaction time can be minimized by routing
the USTAR T signal directly to the UEND input of the
MPI. The timing section of this data sheet contains a
parameter table with delay, setup, and hold timing
requirements to operate the user-logic either synchro-
nously or asynchronously with the MPI host interface
clock.
The user-logic may also assert an active-lo w interrupt
request (UIRQ) to the MPI, which, in turn, asserts an
interrupt to the host processor. Assertion of an inter-
rupt request is asynchronous to the host processor
clock and any read or write transaction occurring in the
MPI. The user-logic is responsible for providing any
required interrupt vectors for the host processor, and
the user-logic must deassert the interrupt request once
serviced. If the interrupt request is not deasserted in
the user logic, it will continue to be asserted to the host
processor via the MPI_IRQ pin.
Table 18. MPI Internal Interface Si
g
nals
Si
g
nal MPI I/O Function
UA
[
3:0
]
OUser Lo
g
ic Address. Addresses up to 16 uni
q
ue user re
g
isters or use as control
si
g
nals.
URDWRN O User Lo
g
ic Read/Write Control Si
g
nal. Hi
g
h indicates a re ad f ro m us er lo
g
ic b
y
the host processor, low indicates a write to user-lo
g
ic b
y
the host processor.
USTART O Active-Hi
g
h User Start Si
g
nal. Indicates the start of an MPI transaction between
the host processor and the user lo
g
ic.
UEND I Active-Hi
g
h User End Si
g
nal. Indicates that the user-lo
g
ic is finished with the
current MPI transaction.
UIRQ IActi v e -L o w In terru
p
t. Sends re
q
uest from the user-lo
g
ic to the host processor.
D
[
7:0
]
FPGA I/O User Data. Ei
g
ht data bits come directl
y
from the FPGA pins—not throu
g
h the
MPI.
MPI_C LK FPGA I MPI Clock. The MPI clock is sourced b
y
the host processor and comes directl
y
from the FPGA pin—not throu
g
h the MPI.
68 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Microprocessor Interface (MPI) (continued)
MPI Setup and C ontrol
The MPI has a series of addressable registers that provide MPI control and status , configuration and readback data
transfer, FPGA device identification, and a dedicated user scratchpad register. All registers are 8 bits wide. The
address map for these registers and the user-logic address space are shown in Table 19, followed by descriptions
of the register and bit functions. Note that f or all registers, the most significant bit is bit 7, and the least significant bit
is bit 0.
Table 19. MPI Setu
p
and Control Re
g
isters
Contr ol Register 1
The MPI control register 1 is a read/write register. The host processor writes a control byte to configure the MPI. It
is readable by the host processor to verify the status of control bits previously written.
Table 20. MPI Setu
p
and Control Re
g
isters Descri
p
tions
Address
(
Hex
)
Re
g
ister
00 Control Re
g
ister 1.
01 Control Re
g
ister 2.
02 Scratchpad Re
g
ister.
03 Status Re
g
ister.
04 Confi
g
uration/Readback Data Re
g
ister.
05 Readback Address Re
g
ister 1
(
bits
[
7:0
])
.
06 Readback Address Re
g
ister 2
(
bits
[
15:8
])
.
07 Device ID Re
g
ister 1
(
bits
[
7:0
])
.
08 Device ID Re
g
ister 2
(
bits
[
15:8
])
.
09 Device ID Re
g
ister 3
(
bits
[
23:16
])
.
0A Device ID Re
g
ister 4
(
bits
[
31:24
])
.
0B—0F Reserved.
10—1F User-definable Address Space.
Bit # Descri
p
tion
Bit 0 GSR In
p
ut. Settin
g
this bit to a 1 invokes a
g
lobal set/reset on the FPGA. The h ost processor must
return this bit to a 0 to remove the GSR si
g
nal. GSR does not affect the re
g
isters at MPI addresses 0
throu
g
h F hexadecimal or an
y
confi
g
uration re
g
isters. Default state = 0.
Bit 1 Reserved.
Bit 2 Reserved.
Bit 3 Reserved.
Bit 4 Reserved.
Bit 5 RD_CFG In
p
ut. Chan
g
in
g
this bit to a 0 after confi
g
uration will initiate readback. The host processor
must return this bit to a 1 to remove the RD_CFG si
g
nal. Since this bit works exactl
y
like the RD_CFG
input pin, please see the FPGA pin descriptions for more information on this si
g
nal. Default state = 1.
Bit 6 Reserved.
Bit 7 PRGM In
p
ut. Settin
g
this bit to a 0 causes the FPGA to be
g
in confi
g
uration and resets the boundar
y
-
scan circuitr
y
. The host processor must return this bit to a 1 to remove the PRGM si
g
nal. Since this bit
works exactl
y
like the PRGM input pin
(
except that it does not reset the MPI
)
, please see the FPGA pin
descriptions for more information on this si
g
nal. Default state = 1.
Lucent Technologies Inc. 69
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Microprocessor Interface (MPI) (continued)
Scratchpad Register
The MPI scratchpad register is an 8-bit read/write register with no defined operation. It may be used for any user-
defined function.
Control Register 2
The MPI control register 2 is a read/write register. The host processor writes a control byte to configure the MPI. It
is readable by the host processor to v erify the status of control bits it had previously written.
Table 21. MPI Control Re
g
ister 2
Bit # Bit Name Descri
p
tion
Bit 0 EN_IRQ_CFG Enable IRQ for Confi
g
uration Data Re
q
uest in Dais
y
-Chain Confi
g
uration
Mode. Settin
g
this bit to a 1 prior to confi
g
uration enables the IRQ si
g
nal to
g
o active
when new data is re
q
uested for confi
g
uration writes or is available for confi
g
uration
reads to/from the confi
g
uration data re
g
ister. A 0 clears the IRQ enable. This bit is
onl
y
valid for dais
y
-chain co nfi
g
uration. Default = 0.
Bit 1 EN_IRQ_ERR Enable IRQ for Bit Stream Error. Settin
g
this bit to a 1 prior to confi
g
uration
enables the IRQ si
g
nal to
g
o active on the occurrence of a bit stream error durin
g
confi
g
uration. A 0 clears the IRQ enable. This bit onl
y
has effect while in c onfi
g
ura-
tion mode. Default = 0.
Bit 2 EN_IRQ_USR Enable IRQ from the U s er F PGA S
p
ace. Settin
g
this bit to a 1 allows user-defined
circuitr
y
in the FPGA to
g
enerate an interrupt to the host processor b
y
sour cin
g
a
lo
g
ic low on the UIRQ si
g
nal in the user lo
g
ic. Default = 0.
Bit 3 MP_DAISY MPI Dais
y
-Chain Out
p
ut Enable. Settin
g
this bit to a 1 enables dais
y
-ch ai n ou t p ut
of the confi
g
uration data. See the Confi
g
uration section of this data sheet for dais
y
-
chain confi
g
uration details. Default = 0.
Bit 4 MP_HOLD_BUS Enable Bus Holdin
g
Durin
g
Dais
y
-Chain Confi
g
uration Mode. Sett in
g
this bit to
a 1 will cause the MPI to wait until the FPGA confi
g
uration lo
g
ic has serialized a
b
y
te of confi
g
uration data before acknowled
g
in
g
the transaction. The data is onl
y
serialized if the MP_DAISY
(
bit 3 above
)
control bit is set to 1. If MP_HOLD_BUS is
set to 0, the MPI will immediatel
y
acknow le d
g
e a confi
g
uration data b
y
te transfer.
Immediate acknowled
g
ment allows the host processor to perform other tasks durin
g
FPGA c onfi
g
uration b
y
pollin
g
the MPI status re
g
ister
(
or b
y
interrupt
)
and onl
y
write
confi
g
uration data when the FPGA is read
y
. Default = 0.
Bit 5 MP_USER MPI User Mode Enable. Settin
g
this bit to a 1 will enable the MPI for user mode
operation. MP_USER must be set prior to the FPGA DONE si
g
nal
g
oin
g
hi
g
h durin
g
confi
g
uration. The MPI ma
y
also be enabled for user operation via the confi
g
urat i on
bit stream. Default = 0.
Bit 6 Reserved —
Bit 7 Reserved —
70 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Microprocessor Interface (MPI) (continued)
Status Register
The microprocessor interface status register is a read-only register, providing information to the host processor.
Table 22. Status Re
g
ister
Configuration Data Register
The MPI configuration data register is a writab le register in configuration mode and a readab le register in readback
mode. For FPGA configuration, this is where the configuration data bytes are sequentially written by the host pro-
cessor. Similarly, for readback mode, the MPI provides the readback data bytes in this register for the host proces-
sor.
Readback Address Register 1
The MPI readback address register 1 is a writable register used to accept the least significant address byte
(bits [7:0]) of the configuration data location to be read back.
Readback Address Register 2
The MPI readback address register 2 is a writable register used to accept the most significant address byte
(bits [15:8]) of the configuration data location to be read back.
Bit # Descri
p
tion
Bit 0 Reserved.
Bit 1 Data Re ad
y
. Set b
y
the MPI, a 1 on this bit durin
g
confi
g
uration alerts the host processor that the FPGA
is read
y
for another b
y
te of co nfi
g
uration data. Durin
g
b
y
te-wide readback, the MPI sets this bit to a 1 to
tell the host processor that a b
y
te of confi
g
uration data is available for readin
g
. This bit is cleared b
y
a
host processor access
(
read or write
)
to the confi
g
uration data re
g
ister.
Bit 2 IRQ Pendin
g
. The MPI sets this bit to 1 to indicate to the host processor that the FPGA has a pendin
g
interrupt re
q
uest. This bit ma
y
be used for the ho st pr oces so r to pol l for int erru pts if the MPI_IRQ pin out-
put of the FPGA has been masked at the host processor. This bit is set to 0 when the status re
g
ister is
read. Interrupt re
q
uests from the FPGA user space must be cleared in FPGA user lo
g
ic in additi on to
readin
g
this bit.
Bits
[
4:3
]
Bit Stream Error Fla
g
s. Bits 3 and 4 are set b
y
the MPI to indicate an
y
error durin
g
FPGA confi
g
ura-
tion. See bit 2 of control re
g
ister 2 for the capabilit
y
to alert the host processor of an error via the IRQ
si
g
nal durin
g
confi
g
uration. In the truth table below , bit 3 is the LSB
(
bit on ri
g
ht
)
. These bits are cleared
to 0 when PRGM
g
oes active:
00 = No error
01 = ID error
10 = Checksum error
11 = Stop -bit/ali
g
nment error
Bit 5 Reserved.
Bit 6 INIT. This bit reflects the binar
y
value of the FPGA INIT pin.
Bit 7 DONE. This bit reflects the binar
y
value of the FPGA DONE pin.
Lucent Technologies Inc. 71
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Microprocessor Interface (MPI) (continued)
Device ID Registers
The MPI de vice ID is broken into four registers holding 1 byte each. The de vice ID that is av ailable through the MPI
is the same as the boundary-scan ID code, e xcept that the device ID in the MPI has a r e v e rs e bi t or der. The re is no
means to ov erwrite any of the de vice ID as can be done with the boundary-scan ID, but the MPI scratchpad register
can be used as a personalization register . The format for the entire de vice ID is shown below f ollow ed by f amily and
device values and the partitioning of the device ID into the four device ID registers.
Table 23. Device ID Code
* PLC arra
y
size of FPGA.
Table 24 shows the family and device values for all parts covered by this data sheet.
Table 24. Series 3 Famil
y
and Device ID Values
Table 25 describes the device IDs for all parts covered by this data sheet as they are partitioned into the four regis-
ters found in the MPI.
Table 25.
ORCA
Series 3 Device ID Descri
p
tions
Version Part*Famil
y
Manufacturer MSB
4 bits 10 bits 6 bits 11 bits 1 bit
Example:
(
First version of Lucent’s OR3C55
)
0000 0100100000 110000 00000011101 1
Part Name Famil
y
ID
(
Hex
)
Device ID
(
Hex
)
OR3T20 03 0C
OR3T30 03 0E
OR3C/T55 03 12
OR3C/T80 03 16
OR3T125 03 1C
Device ID Re
g
ister 1
Bit 0 Lo
g
ic 1. This bit is alwa
y
s a one.
Bits
[
7:1
]
0011101, the 7 least si
g
nificant bits of the Lucent Technolo
g
ies manufacturer ID.
Device ID Re
g
ister 2
Bits
[
3:0
]
0000, the 4 most si
g
nificant bits of the Lucent Technolo
g
ies manufacturer ID.
Bits
[
7:4
]
The 4 least si
g
nificant bits of the 10-bit part number.
Device ID Re
g
ister 3
Bits
[
5:0
]
The 6 most si
g
nificant bits of the 10-bit part number.
Bits
[
7:6
]
The 2 least si
g
nificant bits of the device famil
y
code.
Device ID Re
g
ister 4
Bits
[
3:0
]
The 4 most si
g
nificant bits of the device famil
y
code.
Bits
[
7:4
]
The 4-bit devic e ve rsio n code .
7272 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM)
The
ORCA
programmable clock manager (PCM) is a
special function block that is used to modify or condi-
tion clock signals for optimum system performance.
Some of the functions that can be performed with the
PCM are clock ske w reduction (both internal and board
level), duty-cycle adjustment, clock delay reduction,
clock phase adjustment, and clock frequency multipli-
cation/division. Due to the different capabilities required
by customer application, each PCM contains both a
PLL (phase-locked loop) and a DLL (delayed-locked
loop) mode. By using PLC logic resources in conjunc-
tion with the PCM, many other functions, such as fre-
quency synthesis, are possible.
There are two PCMs on each Series 3 device, one in
the lower left corner and one in the upper right corner.
Each can drive two different, but interrelated clock net-
works inside the FPGA. Each PCM can take a clock
input from the ExpressCLK pad in its corner or from
general routing resources. There are also two input
sources that provide feedback to the PCM from the
PLC array. One of these is a dedicated corner Express-
CLK feedback, and the other is from general routing.
Each PCM sources two clock outputs, one to the corner
ExpressCLK that feeds the CLKCNTRL blocks on the
two sides adjacent to the PCM, and one to the system
clock spine network through general routing. Figure 45
shows a high-level block diagram of the PCM.
Functionality of the PCM is programmed during opera-
tion through a read/write interface internal to the FPGA
array or via the configuration bit stream. The internal
FPGA interface comprises write enab le and read
enable signals, a 3-bit address bus, an 8-bit input (to
the PCM) data bus , and an 8-bit output data b us. There
is also a PCM output signal, LOCK, that indicates a sta-
ble output clock state. These signals are used to pro-
gram a series of registers to configure the PCM
functional core for the desired functionality.
Operation of the PCM is divided into two modes, delay-
locked loop (DLL) and phase-locked loop (PLL). Some
operations can be perf ormed by either mode and some
are specific to a particular mode. These will be
described in each individual mode section. In general,
DLL mode is prefer ab le to PLL mode f or the same func-
tion because it is less sensitive to input clock noise.
In the discussions that follow, the duty cycle is the per-
cent of the clock period during which the output clock is
high.
5-5828(F)
Figure 45. PCM Block Diagram
USER CONTROL SIGNALS
PCM-FPGA
INTERFACE
PCM CORE
FUNCTIONS
CORNER EXPRES SCL K IN
GENERAL CLOCKIN
FEEDBACK
ExpressCLK FEEDBACK CLOCK
FROM ROUTING
EXPRESS CLK O UT
SYSTEM CLOCK OUT
(FROM GENERAL ROUTING) (TO GENERAL ROUTING)
Lucent Technologies Inc. 73
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM) (continued)
PCM Registers
The PCM contains eight user-programmable registers used for configuring the PCM’s functionality. Table 26 shows
the mapping of the registers and their functions. See Figure 46 f or more information on the location of PCM ele-
ments that are discussed in the table. The PCM registers are referenced in the discussions that follow. Detailed
explanations of all register bits are supplied following the functional description of the PCM.
Table 26. PCM Re
g
isters
Address Function
0Divider 0 Pro
g
rammin
g
. Pro
g
rammable divider, DIV0, value and DIV0 reset bit. DIV0 can
divide the input clock to the PCM or can be b
y
passed.
1Divider 1 Pro
g
rammin
g
. Pro
g
rammable divider, DIV1, value and DIV1 reset bit. DIV1 can
divide the feedback clock input to the PCM or can be b
y
pass ed. Valid onl
y
in PLL mode.
2Divider 2 Pro
g
rammin
g
. Pro
g
rammable divider, DIV2, value and DIV2 reset bit. DIV2 can
divide the output of the tapped dela
y
line or can be b
y
passed and is onl
y
valid for the
ExpressCLK output.
3DLL 2x Dut
y
-C
y
cle Pro
g
rammin
g
. DLL mode clock doubler
(
2x
)
dut
y
-c
y
cle selection.
4DLL 1x Dut
y
-C
y
cle Pro
g
rammin
g
. Dependin
g
on the settin
g
s in other re
g
isters, this re
g
is-
ter is for:
a. PLL mode phase/dela
y
selection;
b. DLL mode 1x dut
y
c
y
cle selection; and
c. DLL mode pro
g
rammable dela
y
.
5Mode Pro
g
rammin
g
. DLL/PLL mode se lec ti on, DLL 1x/ 2x clock selection, phas e dete cto r
feed back selection.
6Clock Source Status/Out
p
ut Clock Selection Pro
g
rammin
g
. Input clock selection, feed-
back cl oc k se lect io n, ExpressCLK outp ut sour ce sele cti on, s
y
stem cloc k o u tpu t s ourc e se le c-
tion.
7PCM Control Pro
g
rammin
g
. PCM power, reset, and confi
g
uration control.
74 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM) (continued)
5-5829(F)
Figure 46. PCM Functional Block Diagram
EXPRESSCLK
FROM PROGRAMMABLE
DIVIDER
DIV0
REGISTER 7
REGISTER 6
REGISTER 5
REGISTER 4
REGISTER 3
REGISTER 2
REGISTER 1
REGISTER 0
FPGA-PCM INTERFACE
COMBINATORIAL
LOGIC
PROGRAMMABLE
DIVIDER
DIV2
0
1
2
3
S4
0
1
2
3
S10
0
SYSTEM CLOCK
OUTPUT
EXPRESSCLK
OUTPUT
FROM
EXPRESSCLK
FEEDBACK
FEEDBACK
CLOCK
PROGRAMMABLE
DIVIDER
DIV1
0
1
S2
PHASE
DETECTOR
PROGRAMMABLE DELAY
LINES (32 TAPS)
CHARGE PUMP
AND
LOW-PASS FILTER
1
0
S4
1...7
S5 1...7 1...7 1...7
S6 S7 S8
0
1
2
3
S4
0
1
2
3
S3
PCM
INPUT
CLOCK
DATA_IN[7:0]
ADDR_IN[2:0]
DATA_OUT[7:0]
WE
RE
LOCK
PAD
ROUTING
0
1
2
3
S0
ROUTING
Lucent Technologies Inc. 75
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM)
(continued)
Delay-Locked Loop (DL L) Mo de
DLL mode is used for implementing a delayed clock
(phase adjustment), clock doubling, and duty cycle
adjustment. All DLL functions stem from a delay line
with 32 taps. The delay ed input clock is pulled from v ar-
ious taps and processed to implement the desired
result. There is no feedback clock in DLL mode, provid-
ing a very stable output and a fast loc k time for the out-
put clock.
DLL mode is selected by setting bit 0 in PCM re g iste r
five to a 0. The settings for the various submodes of
DLL mode are described in the following paragraphs.
Divider DIV0 may be used with any of the DLL modes
to divide the input clock by an integer factor of 1 to 8
prior to implementation of the DLL process.
Delayed Clock
A delay ed version of the input clock can be constructed
in DLL mode. The output clock can be delayed by
increments of 1/32 of the input clock period. Express
CLK and system CLK outputs in delay modes are
selected by setting register six, bits [5:4] to 10 or 11 for
ExpressCLK output, and/or bits [7:6] to 10 for system
clock output. The delay v alue is entered in register four.
See register four programming details for more infor-
mation. Delay values are also shown in the second col-
umn of Table 27.
Note that when register six, bits [5:4] are set to 11, the
ExpressCLK output is divided by an integer fac tor from
1 to 8 while the system clock cannot be divided. The
ExpressCLK divider is provided so that the I/O cloc king
provided by the ExpressCLK can operate slower than
the i nte rnal sy st em cl o ck. This al lo ws for very fast inte r-
nal processing while maintaining slower interface
speeds off-chip for improved noise and power perfor-
mance or to interoperate with slower devices in the sys-
tem. The divisor of the ExpressCLK frequency is
selected in register two. See the register two program-
ming details for more information.
1x Clock Duty-Cycle Adjustment
A duty-cycle adjusted replica of the input clock can be
constructed in DLL mode. The duty cycle can be
adjusted in 1/32 (3.125%) increments of the input clock
period. DLL 1x clock mode is selected by setting bit 4
of register fiv e to a 1, and output clock source selection
is selected by setting register six, bits [5:4] to 01 for
ExpressCLK output, and/or bits [7:6] to 01 for system
clock output. The duty-cycle percentage value is
entered in register four. See register four programming
details f or more inf ormation. Duty cycle values are also
shown in the third column of Table 27.
Table 27. DLL Mode Dela
y
/1x Dut
y
C
y
cle
Pro
g
rammin
g
Values
Re
g
ister 4 [7:0]
7 6 5 4 3 2 1 0 Dela
y
(
CLK_IN/32
)
Dut
y
C
y
cle
(
% of CLK_IN
)
0 0 X X X 0 0 0 1 3.125
0 0 X X X 0 0 1 2 6.250
0 0 X X X 0 1 0 3 9.375
0 0 X X X 0 1 1 4 12.500
0 0 X X X 1 0 0 5 15.625
0 0 X X X 1 0 1 6 18.750
0 0 X X X 1 1 0 7 21.875
0 0 X X X 1 1 1 8 25.000
0 1 X X X 0 0 0 9 28.125
0 1 X X X 0 0 1 10 31.250
0 1 X X X 0 1 0 11 34.375
0 1 X X X 0 1 1 12 37.500
0 1 X X X 1 0 0 13 40.625
0 1 X X X 1 0 1 14 43.750
0 1 X X X 1 1 0 15 46.875
0 1 1 1 1 X X X 16 50.000
1 0 0 0 0 X X X 17 53.125
1 0 0 0 1 X X X 18 56.250
1 0 0 1 0 X X X 19 59.375
1 0 0 1 1 X X X 20 62.500
1 0 1 0 0 X X X 21 65.625
1 0 1 0 1 X X X 22 68.750
1 0 1 1 0 X X X 23 71.875
1 0 1 1 1 X X X 24 75.000
1 1 0 0 0 X X X 25 78.125
1 1 0 0 1 X X X 26 81.250
1 1 0 1 0 X X X 27 84.375
1 1 0 1 1 X X X 28 87.500
1 1 1 0 0 X X X 29 90.625
1 1 1 0 1 X X X 30 93.750
1 1 1 1 0 X X X 31 96.875
7676 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM)
(continued)
2x Clock Duty-Cycle Adjustment
A doubled-frequency, duty-cycle adjusted version of the
input clock can be constructed in DLL mode. The first
cloc k cycl e of the 2x clo ck out put occurs when the inp ut
clock is high, and the second cycle occurs when the
input clock is low. The duty cycle can be adjusted in
1/32 (6.25%) increments of the input clock period.
Additionally, each of the two doubled-clock cycles that
occurs in a single input clock cycle may be adjusted to
have different duty cycles. DLL 2x clock mode is
selected by setting bit 4 of register five to a 1, and by
setting register six, bits [5:4] to 01 for ExpressCLK out-
put, and/or bits [7:6] to 01 for system clock output. The
duty-cycle percentage value is entered in register
three. See register three programming details for more
information. Duty-cycle v alues where both cycles of the
doubled clock ha ve the same duty cycle are also shown
in Table 28.
Table 28. DLL Mode Dela
y
/2x Dut
y
C
y
cle
Pro
g
rammin
g
Values
Phase-Locked Loop (PLL) Mode
The PLL mode of the PCM is used for clock multiplica-
tion (1/8x to 64x) and clock delay minimization func-
tions. PLL functions make use of the PCM divi ders and
use feedback signals, often from the FPGA array. The
use of feedback is discussed with each PLL submode.
PLL mode is selected by setting bit 0 of register five to
1.
Clock Delay Minimization
PLL mode can be used to minimize the effects of the
input buffer and input routing delay on the clock signal.
PLL mode causes a feedback clock signal to align in
phase with the input clock (refer back to the block dia-
gram in Figure 45) so that the dela y between them is
effectively eliminated.
There is a dedicated feedback path from an adjacent
middle CLKCNTRL block to the PCM. Using the corner
ExpressCLK pad as the input to the PCM and using this
dedicated feedback path, the clock from the Express-
CLK output of the PCM, as vie wed at the CLKCNTRL
block, will be phase-aligned with the ExpressCLK input
to the PCM. These relationships are diagrammed in
Figure 47.
A feedback clock can also be input to the PCM from
general routing. This allows for compensating for delay
between the PCM input and a point in the general rout-
ing. The use of this routed-feedbac k path is not gener-
ally recommended. Because compensation is based
on the programmable routing, the amount of clock
delay compensation can v ary between FPGA lots and
fabrication processes, and will vary each time that the
feedback line is routed using different resources. Con-
tact Lucent Technologies for application notes regard-
ing the use of routed-feedback delay compensation.
5-5980(F)
Fi
g
ure 47. Ex
p
ressCLK Dela
y
Minimization
Usin
g
the PCM
Re
g
ister 3 [7:0]
7 6 5 4 3 2 1 0 Dut
y
C
y
cle
(
%
)
0 0 0 0 0 0 0 0 6.25
0 0 0 0 1 0 0 1 12.50
0 0 0 1 0 0 1 0 18.75
0 0 0 1 1 0 1 1 25.00
0 0 1 0 0 1 0 0 31.25
0 0 1 0 1 1 0 1 37.50
0 0 1 1 0 1 1 0 43.75
0 0 1 1 1 1 1 1 50.00
1 1 0 0 0 0 0 0 56.25
1 1 0 0 1 0 0 1 62.50
1 1 0 1 0 0 1 0 68.75
1 1 0 1 1 0 1 1 75.00
1 1 1 0 0 1 0 0 81.25
1 1 1 0 1 1 0 1 87.50
1 1 1 1 0 1 1 0 93.75
CORNER
CLKCNTRL
CLKCNTRL
DELAY
DELAY IS COMP EN SA TE D
INPUT
OUTPUT WITHOUT
USING PCM
OUTPUT
EXPRESSCLK
EXPRESSCLK
USING PCM
EXPRESSCLK
COMPENSATION EQUALS DELAY
Lucent Technologies Inc. 77
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM)
(continued)
Clock Multiplication
An output clock that is a multiple (not necessarily an
integer multiple) of the input clock can be generated in
PLL mode. The multiplication ratio is programmed in
the division registers DIV0, DIV1, and DIV2. Note that
DIV2 applies only to the ExpressCLK output of the
PCM and any reference to DIV2 is implicitly 1 for the
system clock output of the PCM. The clock multiplica-
tion formulas when using ExpressCLK feedback are:
Where the values of DIV0, DIV1, and DIV2 range from
1 to 8.
The ExpressCLK multiplication range of output clock
frequencies is, therefore, from 1/8x up to 8x, with the
syste m cloc k r ange up to 8x th e ExpressCLK frequency
or 64x the input clock frequency. If system clock feed-
back is used, the formulas are:
The divider values, DIV0, DIV1, and DIV2 are pro-
grammed in registers zero, one, and two, respectively.
The multiplied output is selected by setting register six,
bits [5:4] to 10 or 11 for ExpressCLK output and/or bits
[7:6] to 10 for system clock output. Note that when reg-
ister six, bits [5:4] are set to 11, the ExpressCLK output
is divided by DIV2, while the system clock cannot be
divided. The ExpressCLK divider is provided so that the
I/O clocking provided by the ExpressCLK can operate
slower than the internal system clock. This allows for
very fast internal processing while maintaining slower
interface speeds off-chip for improv ed noise and power
performance or to interoperate with slower devices in
the system.
It is also necessary to configure the internal PCM oscil-
lator for operation in the proper frequency range.
Table 29 and Table 30 show the settings required for
register four for a given frequency range for Series 3C
and 3T devices. In addition, the acquisition time is
shown for each frequency range. This is the time that is
required for the PCM to acquire LOCK. The PCM oscil-
lator frequency range is chosen based on the desired
output frequency at the system clock output. If using
the ExpressCLK output, the equivalent system clock
frequency can be selected by multiplying the expected
ExpressCLK output frequency by the value for DIV2.
Choose the nominal frequency from the table that is
closest to the desired frequency, and use that value to
program register four. Minor adjustments to match the
e xact input frequency are then perf ormed automatically
by the PCM.
FExpressCLK_OUT = FINPUT_CLOCK • DIV1
DIV0
FSYSTEM_CLOCK_OUT = FExpressCLK_OUT • DIV2
FSYSTEM_CLOCK_OUT = FINPUT_CLOCK • DIV1
DIV0
FExpressCLK_OUT = FSYSTEM_CLOCK/DIV2
7878 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM)
(continued)
Table 29. PCM Oscillator Fre
q
uenc
y
Ran
g
e 3Txxx
Note: Use of settin
g
s in the first three rows is not recommended.
X means don’t care.
Table 30. PCM Oscillator Fre
q
uenc
y
Ran
g
e 3Cxx
Note: Use of settin
g
s in the first three rows is not recommended.
X means don’t care.
Re
g
ister 4
76543210 Min
(
MHz
)
S
y
stem
Clock
Out
p
ut
Fre
q
uenc
y
(
MHz
)
NOM Max
(
MHz
)
T
Ac
q
uisition
(
µs
)
00XXX010 17.00 58.50 100.00 36.00
00XXX011 16.10 52.50 89.00 37.00
00XXX100 15.17 49.00 82.80 38.00
00XXX101 14.25 45.00 76.50 39.00
00XXX110 13.33 41.50 70.30 40.00
00XXX111 12.40 38.00 64.00 41.00
01XXX000 12.20 36.75 61.30 43.75
01XXX001 12.10 35.00 58.00 46.50
01XXX010 11.90 33.00 54.30 49.25
01XXX011 11.70 31.30 51.00 52.00
01XXX100 11.10 30.00 49.40 54.75
01XXX101 10.50 29.15 47.80 57.50
01XXX110 10.00 28.10 46.20 60.25
01XXX111 9.40 27.00 44.60 63.00
10000XXX 9.20 26.25 43.30 65.40
10001XXX 9.00 25.65 42.30 67.80
10010XXX 8.80 25.00 41.30 70.10
10011XXX 8.60 24.45 40.30 72.50
10100XXX 8.40 23.70 39.00 74.90
10101XXX 8.10 22.90 37.70 77.30
10110XXX 7.90 22.20 36.50 79.60
10111XXX 7.70 21.50 35.20 82.00
11000XXX 7.60 20.80 34.00 84.30
11001XXX 7.45 20.10 32.80 86.50
11010XXX 7.30 19.45 31.60 88.80
11011XXX 7.20 18.85 30.50 91.00
11100XXX 6.60 18.30 30.00 93.30
11101XXX 6.00 17.70 29.40 95.50
11110XXX 5.50 17.10 28.60 97.80
11111XXX 5.00 16.50 28.00 100.00
Re
g
ister 4
76543210 Min
(
MHz
)
S
y
stem
Clock
Out
p
ut
Fre
q
uenc
y
(
MHz
)
NOM Max
(
MHz
)
T
Ac
q
uisition
(
µs
)
00XXX010 10.50 73.00 135.00 36.00
00XXX011 10.00 68.00 126.00 37.00
00XXX100 9.50 63.00 117.00 38.00
00XXX101 9.10 58.50 108.00 39.00
00XXX110 8.60 53.80 99.00 40.00
00XXX111 8.10 49.00 90.00 41.00
01XXX000 7.80 47.70 87.50 43.80
01XXX001 7.60 46.30 85.00 46.50
01XXX010 7.30 45.00 82.50 49.30
01XXX011 7.10 43.60 80.00 52.00
01XXX100 6.80 42.10 77.50 55.00
01XXX101 6.50 40.75 75.00 57.50
01XXX110 6.30 39.40 72.50 60.30
01XXX111 6.00 38.00 70.00 63.00
10000XXX 5.90 37.40 68.80 65.40
10001XXX 5.90 36.70 67.50 67.80
10010XXX 5.80 36.00 66.30 70.10
10011XXX 5.80 35.40 65.00 72.50
10100XXX 5.70 35.00 63.80 74.90
10101XXX 5.60 34.10 62.50 77.30
10110XXX 5.60 33.50 61.30 79.60
10111XXX 5.50 32.80 60.00 82.00
11000XXX 5.40 32.10 58.80 84.30
11001XXX 5.40 31.50 57.50 86.50
11010XXX 5.30 30.70 56.30 88.80
11011XXX 5.30 30.10 55.00 91.00
11100XXX 5.20 29.50 53.80 93.30
11101XXX 5.10 28.80 52.50 95.50
11110XXX 5.10 28.20 51.30 97.80
11111XXX 5.00 27.50 50.00 100.00
Lucent Technologies Inc. 79
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM)
(continued)
PCM/FPGA Internal Interface
Writing and reading the PCM registers is done through
a simple asynchronous interface that connects with the
FPGA routing resources. Reads from the PCM by the
FPGA logic are accomplished by setting up the 3-bit
address, A[2:0], and then applying an active-high read
enable (RE) pulse. The read data will be available as
long as RE is held high. The address may be changed
while RE is high, to read other addresses. When RE
goes low, the data output bus is 3-stated.
Writes to the PCM by the FPGA logic are performed by
applying the write data to the data input bus of the
PCM, applying the 3-bit address to write to, and assert-
ing the write enable (WE) signal high. Data will be writ-
ten by the high-going transition of the WE pulse.
The read enable (RE) and write enable (WE) signals
may not be active at the same time. For detailed timing
information and specifications, see the Timing Charac-
teristics section of this data sheet.
The LOCK signal output from the PCM to the FPGA
routing indicates a stable output clock signal from the
PCM. The LOCK signal is high when the PCM output
clock parameters fall within the programmed values
and the PCM specifications for jitter. Due to phase cor-
rections that occur internal to the PCM, the LOCK sig-
nal might occasionally pulse lo w when the output clock
is out of specification for only one or two clock cycles
(high jitter due to temperature, voltage fluctuation, etc.)
To accommodate these pu lses, it is suggested that the
user integr ate the LOCK signal ov er a period suitable to
their application to achieve the desired usage of the
LOCK signal.
The LOCK signal will also pulse high and low during
the acquisition time as the output clock stabilizes. True
LOCK is only achiev ed when the LOCK signal is a solid
high. Again, it is suggested that the user integrate the
LOCK signal over a time period suitable to the subject
application.
PCM Operation
Several features are availab le for the control of the
PCM’s overall operation. The PCM ma y be programma-
bly enabled/disabled via bit 0 of register 7. When dis-
abled, the analog power supply of the PCM is turned
off, conserving power and eliminating the possibility of
inducing noise into the system power buses. Individual
bits (register 7, bits [2:1]) are provided to reset the DLL
and PLL functions of the PCM. These resets aff ect only
the logic generating the DLL or PLL function; they do
not reset the divider values (DIV0, DIV1, DIV2) or reg-
isters [7:0]. The global set/reset (GSRN) is also pro-
grammably controlled via register 7, bit 7. If register 7,
bit 7 is set to 1, GSRN will have no effect on the PCM
logic, allowing the clock to operate during a global
set/reset. This function allows the FPGA to be reset
without affecting a clock that is sent off-chip and used
elsewhere in the system. Bit 6 of register 7 affects the
functionality of the PCM during configuration. If set to 1,
this bit enables the PCM to operate during configura-
tion, after the PCM has been configured. The PCM
functionality is programmed via the bit stream. If regis-
ter 7, bit 6 is 0, the PCM cannot function and its pow er
supply is disabled until after the configuration DONE
signal goe s high .
When the PCM is pow ered up via register 7, bit 0, there
is a wake-up time associated with its operation. Follow-
ing the wake-up time, the PCM will begin to fully func-
tion, and, f ollowing an acquisition time during which the
output clock may be unsta ble, the PCM will be in
steady-state operation. There is also a shutdown time
associated with powering off the PCM. The output
clock will be unstable during this period. Waveforms
and timing parameters can be found in the Timing
Characteristics section of this data sheet.
80 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM) (continued)
PCM Detailed Programming
Descriptions of bit fields and individual control bits in the PCM control registers are provided in Table 31. Refer to
Figure 46 f or more inf ormation on the location of the PCM elements that are discussed. In the following discussion,
the duty cycle is in the percentage of the clock period where the clock is high.
Table 31. PCM Control Re
g
isters
Bit # Function
Re
g
ister 0—Divider 0 Pro
g
rammin
g
Bits
[
3:0
]
4-Bit Divider, DIV0, Value. This value enables the input clock to immediatel
y
be divided b
y
a
value from 1 to 8. A 0 value
(
the default
)
indicates that DIV0 is b
y
passed
(
no division
)
. B
y
pass
incurs less dela
y
than dividin
g
b
y
1. Hexadecimal values
g
reater than 8 for bits
[
3:0
]
y
ield their
modulo 8 value. For example, if bits
[
3:0
]
are 1001
(
9 hex
)
, the result is divide b
y
1
(
remainder
9/8 = 1
)
.
Bits
[
6:4
]
Reserved.
Bit 7 DIV 0 Reset Bit. DIV0 ma
y
not be reset b
y
GSRN dependin
g
on the value of re
g
ister 7, bit 7.
This bit ma
y
be set to 1 to reset DIV0 to its default value. Bit 0 must be set to 0
(
the default
)
to
remove the reset.
Re
g
ister 1—Divider 1 Pro
g
rammin
g
Bits
[
3:0
]
4-Bit Divider, DIV1, Value. This value enables the feedback clock to be divided b
y
a value from
1 to 8. A 0 value
(
the default
)
indicates that DIV1 is b
y
passed
(
no division
)
. B
y
pass incurs less
dela
y
than dividin
g
b
y
1. Hexadecimal values
g
reater than 8 for bits
[
3:0
]
y
ield their modulo 8
value. For example, if bits
[
3:0
]
are 1001
(
9 hex
)
, the result is divide b
y
1
(
remainder 9/8 = 1
)
.
Bits
[
6:4
]
Reserved.
Bit 7 DIV1 Reset Bit. DIV1 ma
y
not be reset b
y
GSRN, dependi n
g
on the value of re
g
ister 7, bit 7.
This bit ma
y
be set to 1 to reset DIV1 to its default value. Bit 0 must be set to 0
(
the default
)
to
remove the reset.
Re
g
ister 2—Divider 2 Pro
g
rammin
g
Bits
[
3:0
]
4-Bit Divider, DIV2, Value. This value enables the tapped dela
y
line output clock driven onto
ExpressCLK to be divided b
y
a value from 1 to 8. A 0 value
(
the default
)
indicates that DIV2 is
b
y
passed
(
no divi si on
)
. B
y
pass in cu rs less d e la
y
than di vi d in
g
b
y
1. Hexadecimal values
g
reater
than 8 for bits
[
3:0
]
y
ield their modulo 8 value. For example, if bits
[
3:0
]
are 1001
(
9 hex
)
, the
result is divide b
y
1
(
remainder 9/8 = 1
)
.
Bits
[
6:4
]
Reserved.
Bit 7 DIV2 Reset Bit. DIV2 ma
y
not be reset b
y
GSRN, dependi n
g
on the value of re
g
ister 7, bit 7.
This bit ma
y
be set to 1 to reset DIV2 to its default value. Bit 7 must be set to 0
(
the default
)
to
remove the reset.
Re
g
ister 3—DLL 2x Dut
y
-C
y
cle Pro
g
rammin
g
Bits
[
2:0
]
Dut
y
-c
y
cle selection for the doubled clock period associated with the input clock hi
g
h. The dut
y
c
y
cle is
(
value of bit 6
)
* 50% +
((
value of bits
[
2:0
])
+ 1
)
* 6.25%. See the description for bit 6.
Bits
[
5:3
]
Dut
y
-c
y
cle selection for the doubled clock period associated with the input clock low. The dut
y
c
y
cle is
(
value of bit 7
)
* 50% +
((
value of bits
[
2:0
])
+ 1
)
* 6.25%. See the description for bit 7.
Bit 6 Master dut
y
-c
y
cle control for the first clock period of the doubled clock: 0 = less than or e
q
ual to
50%, 1 =
g
reater than 50%.
Bit 7 Master dut
y
-c
y
cle control for the second clock period of the doubled clock: 0 = less than or e
q
ual
to 50%, 1 =
g
reater than 50%. Example: Both clock periods havin
g
a 62.5% dut
y
c
y
cle, bi t s
[
7:0
]
are 11 001 001.
Lucent Technologies Inc. 81
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM) (continued)
Table 31. PCM Control Registers (continued)
Bit # Function
Re
g
ister 4—DLL 1x Dut
y
-C
y
cle Pro
g
rammin
g
Bits
[
2:0
]
Dut
y
-C
y
cle/Dela
y
Selection for Dut
y
C
y
cle/Dela
y
s Less Than or E
q
ual to 50%. The dut
y
-
c
y
cle/dela
y
is
(
value of bits
[
7:6
])
* 25% +
((
value of bits
[
2:0
])
+ 1
)
* 3.125%. See the description
for bits
[
7:6
]
.
Bits
[
5:3
]
Dut
y
-C
y
cle/Dela
y
Selection for Dut
y
C
y
cle/Dela
y
s Greater Than 50%. The dut
y
-c
y
cle/dela
y
is
(
value of bits
[
7:6
])
* 25% +
((
value of bits
[
5:3
])
+ 1
)
* 3.125%. See the description for bits
[
7:6
]
.
Bits
[
7:6
]
Master Dut
y
C
y
cle Control:
00: dut
y
c
y
cle 3.125% to 25%
01: dut
y
c
y
cle 28.125% to 50%
10: dut
y
c
y
cle 53.125% to 75%
11: dut
y
c
y
cle 78.125% to 96.875%
Example: A 40.625% dut
y
c
y
cle, bits
[
7:0
]
are 01 XXX 100, where X is a don’t care because the
dut
y
c
y
cle is not
g
reater than 50%.
Example: The PCM output clock should be dela
y
ed 96.875%
(
31/32
)
of the input clock period.
Bits
[
7:0
]
are 11110XXX, which is 78.125% from bits
[
7:6
]
and 18.75% from bits
[
5:3
]
. Bits
[
2:0
]
are don’t care
(
X
)
because the dela
y
is
g
reater than 50%.
Re
g
ister 5—Mode Pro
g
rammin
g
Bit 0 DLL/PLL Mode Selection Bit. 0 = DLL, 1 = PLL. Default is DLL mode.
Bit 1 Reserved.
Bit 2 PLL Phase Detector Feedback In
p
ut Selection Bit. 0 = feedback si
g
nal from routin
g
/
ExpressCLK, 1 = feedback from pro
g
rammab le del a
y
line output. Default is 0. Has no effect in
DLL mode.
Bit 3 Reserved.
Bit 4 1x/2x Clock Selection Bit for DLL Mode. 0 = 1x clock output, 1 = 2x clock output. Default is 1x
clock out put. Has no effect in PLL mode.
Bits
[
7:5
]
Reserved.
82 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM) (continued)
Table 31. PCM Control Registers (continued)
Bit # Function
Bits
[
5:4
]
ExpressCLK Out
p
ut Source Selector. Default is 00.
00: PCM input clock, b
y
pass path throu
g
h PCM
01: DLL output
10: tapped dela
y
line output
11: divided
(
DIV2
)
dela
y
line output
Bits
[
7:6
]
S
y
stem Clock Out
p
ut Source Selector. Default is 00.
00: PCM input clock, b
y
pass path throu
g
h PCM
01: DLL output
10: tapped dela
y
line output
11: reserved
Re
g
ister 7—PCM Control Pro
g
rammin
g
Bit 0 PCM Anal o
g
Power Su
pp
l
y
Switch. 1 = power suppl
y
on, 0 = power suppl
y
off.
Bit 1 PCM Reset. A value of 1 resets all PCM lo
g
ic for PLL and DLL modes.
Bit 2 DLL Reset. A value o f 1 rese t s the clo ck
g
eneration lo
g
ic for DLL mode. No dividers or user re
g
-
isters are affected.
Bits
[
5:3
]
Reserved.
Bit 6 PCM Confi
g
uration O
p
eration Enable Bit. 0 = normal confi
g
uration opera tion. Durin
g
confi
g
u-
ration
(
DONE = 0
)
, the PCM analo
g
pow er supp l
y
will be off, the PCM output data bus is 3-stated,
and the LOCK si
g
nal is asserted to lo
g
ic 0. The PCM will power up when DONE = 1.
1 = PCM operation durin
g
confi
g
uration. The PCM ma
y
be powered up
(
see bit 0
)
and be
g
in
operation, or continue operation. The setup of the PCM can be performed via the confi
g
uration
bit stream.
Bit 7 PCM GSRN Enable Bit. 0 = normal GSRN operation. 1 = GSRN has no effect on PCM lo
g
ic, so
clock processin
g
will not be interrupted b
y
a chip reset. Default is 0.
Lucent Technologies Inc. 83
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM)
(continued)
PCM Applications
The applications discussed below are only a small
sampling of the possible uses for the PCM. Check the
Lucent Technologies
ORCA
FPGA Internet website
(listed at the end of this data sheet) for additional appli-
cation notes.
Clock Phase Adjustment
The PCM may be used to adjust the phase of the input
clock. The result is an output clock which has its active
edge either preceding or following the active edge of
the input clock. Clock phase adjustment is accom-
plished in DLL mode by delaying the clock. This is dis-
cussed in the Delay-Locked Loop (DLL) Mode section.
Examples of using the dela y ed clock as an early or late
phase-adjusted clock are outlined in the following para-
graphs.
An output clock that precedes the input clock can be
used to compensate for clock delay that is largely due
to excessive loading. The preceding output clock is
really not early relative to the input clock, but is delay ed
almost a full cycle. This is shown in Figure 48A. The
amount of delay that is being compensated for, plus
clock setup time and some margin, is the amount less
than one full cloc k cycle that the output clock is dela yed
from the input clock.
In some systems, it is desirable to operate logic from
sev eral clocks that operate at different phases. This
technique is often used in microprocessor-based sys-
tems to transfer and process data synchronously
between functional areas, but without incurring exces-
sive delays. Figure 48B shows an input clock and an
output clock operating 180° out of phase. It also shows
a version of the input clock that was shifted approxi-
mately 180° using logic gates to create an inverter.
Note that the inverted clock is really shifted more than
180° due to the propagation delay of the inverter. The
PCM output clock does not suffer from this delay. Addi-
tionally, the 180° shifted PCM output could be shifted
by some smaller amount to eff ect an early 180° shifted
clock that also accounts for loading effects.
In terms of degrees of phase shift, the phase of a clock
is adjustable in DLL mode with resolution relativ e to the
delay increment (see Table 27):
Phase Ad
j
ustment =
(
Dela
y)
* 11.25, Dela
y
< 16
Phase Ad
j
ustment =
((
Dela
y)
* 11.25
)
– 360, Dela
y
> 16
5-5979(F)
Figure 48. Clock Phase Adjustment Using the PCM
INP UT CL O C K
OUTPUT CLOCK
INP UT CL O C K
PCM OUTPUT CLOCK
INVERTED INPUT CLOCK
A. Generating an Early Clock
B. Multiphase Clock Generation U sing the DLL
UNINTENDED PHASE
SHIFT DUE TO
INVER TER DE LAY DLL DELAY
DLL DEL AY CLOCK DELAY AND SETUP
BEING COMPENSATED
8484 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Programmable Clock Manager (PCM)
(continued)
High-Speed Internal Pr ocessing with Slow I/Os
The PCM PLL mode provides two outputs, one sent to
the global system cloc k routing of the FPGA and the
other to the ExpressCLK(s) that serve the FPGA I/Os.
The ExpressCLK output of the PCM has a divide capa-
bility (DIV2) that the system clock output does not. This
feature allows an input clock to be multiplied up to a
higher frequency for high-speed internal processing,
and also allows the ExpressCLK output to be divided
down to a lower frequency to accommodate off-FPGA
data trans fers. For example, a 10 MHz input clock may
be multiplied (see Clock Multiplication in the Phase-
Lock ed Loop (PLL) Mode subsection) to 25 MHz (DIV0
= 4, DIV1 = 5, DIV2 = 2) and output to the FPGA
ExpressCLK. This allows the I/Os of the circuit to run at
25 MHz ((2 * 5)/4 * 10 MHz). The system clock will run
at DIV2 times the ExpressCLK rate, which is 2 times
25 MHz, or 50 MHz. This setup allows for internal pro-
cessing to occur at twice the rate of on/off device I/O
transfers.
PCM Cautions
Cautions do apply when using the PCM. There are a
number of configurations that are possible in the PCM
that are theoretically valid, but may not produce viable
results. This section describes some of those situa-
tions, and should leave the user with an understanding
of the types of pitfalls that must be avoided when modi-
fying clock signals.
Resultant signals from the PCM must meet the FPGA
timing specifications. It is possible to specify pulses by
using duty-cycle adjustments that are too narrow to
function in the FPGA. F or instance, if a 40 MHz clock is
doubled to 80 MHz and a 6.25% duty cycle is selected,
the result will be a 780 ps pulse that repeats every
12.5 ns. This pulse falls outside of the clock pulse width
specifi c atio n and is not valid.
Using divider DIV2, it is possible to specify a clock mul-
tiplication factor of 64 between the input clock and the
output system clock. As mentioned above , the resultant
frequency must meet all FPGA timing specifications.
The input clock must also meet the minimum specifica-
tions. An input clock rate that is below the PCM clock
minimum cannot be used e ven if the multiplied output is
within the allowable range.
The use of the PCM to tweak a clock signal to eliminate
a particular problem, such as a single setup time viola-
tion, is discouraged. A small shift in delay, duty cycle, or
phase to correct a single-point problem is in essence
an asynchronous patch to a synchronous system, mak-
ing the system less stable. This type of local problem,
as opposed to a global clock control issue like device-
wide clock delay, can usually be eliminated through
more robust design practices. If this type of change is
made, the designer must be aware that depending on
the extent of the change made, the design may fail to
operate correctly in a different speed grade or voltage
grade (e.g., 3C vs. 3T), or ev en in a diff erent production
lot of the same device.
Divider DIV2 is available in DLL mode for the Express-
CLK output, but its use is not recommended with duty-
cycle adjusted clocks.
Lucent Technologies Inc. 85
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
FPGA States of Operation
Prior to becoming operational, the FPGA goes through
a sequence of states, including initialization, configura-
tion, and start-up . Figure 49 outlines these three FPGA
states.
Figure 49. FPGA States of Operation
Initialization
Upon powerup , the device goes through an initialization
process. First, an internal power-on-reset circuit is trig-
gered when power is applied. When VDD reaches the
v oltage at which portions of the FPGA begin to operate
(2.5 V to 3 V for the OR3Cxx, 2.2 V to 2.7 V for the
OR3Txxx), the I/Os are configured based on the con-
figuration mode, as determined by the mode select
inputs M[2:0]. A time-out delay is initiated when VDD
reaches between 3.0 V and 4.0 V (OR3Cxx) or 2.7 V to
3.0 V (OR3Txxx) to allow the power supply voltage to
stabiliz e. The INIT and DONE outputs are low. At pow-
erup , if VDD does not rise from 2.0 V to VDD in le ss th an
25 ms, the user should delay configuration by inputting
a low into INIT, PRGM, or RESET until VDD is greater
than the recommended minimum operating v oltage
(4.75 V for OR3Cxx commercial devices and 3.0 V for
OR3Txxx devices).
At the end of initialization, the default configuration
option is that the configuration RAM is written to a low
state. This prevents shorts prior to configuration. As a
configuration option, after the first configuration (i.e., at
reconfiguration), the user can reconfigure without
clearing the internal configuration RAM first. The
active-low, open-drain initialization signal INIT is
released and must be pulled high by an external resis-
tor when initialization is complete. To synchronize the
configuration of multiple FPGAs, one or more INIT pins
should be wire-ANDed. If INIT is held low b y one or
more FPGAs or an external device, the FPGA remains
in the initialization state. INIT can be used to signal that
the FPGAs are not yet initialized. After INIT goes high
for two internal clock cycles, the mode lines (M[3:0])
are sampled, and the FPGA enters the configuration
state.
The high during configuration (HDC), lo w during config-
uration (LDC), and DONE si gnals are active outputs in
the FPGA’ s initialization and configuration states . HDC,
LDC, and DONE can be used to provide control of
external logic signals such as reset, bus enable, or
PROM enable during configuration. For parallel master
configuration modes, these signals provide PROM
enable control and allow the data pins to be shared
with user logic signals.
5-4529(F)
– ACTIVE I/O
– RELEASE INTERNAL RESET
– DONE GOES HIGH
START-UP
INITIALIZATION
CONFIGURATION RESET
OR
PRGM
LOW
PRGM
LOW
– CLEAR CONFIGURATION
– INIT LOW, HDC HIGH, LDC LOW
OPERATION
POWERUP
– POWER-ON TIME DELAY
– M[3:0] MODE IS SELECTED
– CONFIGURATION DATA FRAME
– INIT HIGH, HDC HIGH, LDC LOW
– DOUT ACTIVE
YES
NO NO
RESET,
INIT,
OR
PRGM
LOW
BIT
ERROR YES
WRITTEN
MEMORY
8686 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
FPGA States of Operation (continued)
If configuration has begun, an assertion of RESET or
PRGM initiates an abort, returning the FPGA to the ini-
tialization state. The PRGM and RESET pins must be
pulled back high before the FPGA will enter the config-
uration state. During the start-up and operating states,
only the assertion of PRGM causes a reconfiguration.
In the master configuration modes, the FPGA is the
source of configuration clock (CCLK). In this mode, the
initialization state is extended to ensure that, in daisy-
chain operation, all daisy-chained slave devices are
ready. Independent of differences in cloc k rates , master
mode devices remain in the initialization state an addi-
tional six internal clock cycles after INIT goes high.
When configuration is initiated, a counter in the FPGA
is set to 0 and begins to count configuration clock
cycles applied to the FPGA. As each configuration data
frame is supplied to the FPGA, it is internally assem-
bled into data words. Each data word is loaded into the
internal configuration memory. The configuration load-
ing process is complete when the internal length count
equals the loaded length count in the length count field,
and the required end of configuration frame is written.
All OR3Cxx I/Os operate as TTL inputs during configu-
ration (OR3Txxx I/Os are CMOS-only). All I/Os that are
not used during the configuration process are
3-stated with internal pull-ups.
Warning: During configuration, all OR3Txxx inputs
have internal pull-ups enabled. If these inputs are
driv en to 5V, the y will draw substantial current (≅ 5 ma).
This is due to the fact that the inputs are pulled up to
3V.
During configuration, the PIC and PLC latches/FFs are
held set/reset and the internal BIDI buffers are 3-
stated. The combinatorial logic begins to function as
the FPGA is configured. Figure 50 shows the general
waveform of the initialization, configuration, and start-
up states.
Configuration
The
ORCA
Series FPGA functionality is determined by
the state of internal configuration RAM. This configura-
tion RAM can be loaded in a number of different
modes. In these configuration modes, the FPGA can
act as a master or a slave of other devices in the sys-
tem. The decision as to which configuration mode to
use is a system design issue. Configuration is dis-
cussed in detail, including the configuration data f ormat
and the configuration modes used to load the configu-
ration data in the FPGA, follo wing a description of the
start-up state.
5-4482(F)
Fi
g
ure 50. Initialization/Confi
g
uration/Start-U
p
Waveforms
V
DD
M[3:0]
CCLK
HDC
LDC
DONE
USER I/O
INTERNAL
RESET
(gsrn)
CONFIGURATION
OPERATION
INITIALIZATION
START-UP
RESET
PRGM
INIT
Lucent Technologies Inc. 87
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
FPGA States of Operation (continued)
Start-Up
After configuration, the FPGA enters the start-up
phase. This phase is the transition between the config-
uration and operational states and begins when the
number of CCLKs received after INIT goes high is equal
to the value of the length count field in the configuration
frame and when the end of configuration frame has
been written. The system design issue in the start-up
phase is to ensure the user I/Os become active without
inadvertently activating devices in the system or caus-
ing bus contention. A second system design concern is
the timing of the release of glob al set/r eset of the P LC
latches/FFs .
There are configuration options that control the relativ e
timing of three e vents: DONE going high, release of the
set/reset of internal FFs, and user I/Os becoming
active. Figure 51 shows the start-up timing for
ORCA
FPGAs. The system designer determines the relative
timing of the I/Os becoming active, DONE going high,
and the release of the set/reset of internal FFs. In the
ORCA
Series FPGA, the three e vents can occur in any
arbitrary sequence. This means that they can occur
before or after each other, or they can occur simulta-
neously.
There are four main start-up modes: CCLK_NOSYNC,
CCLK_SYNC, UCLK_NOSYNC, and UCLK_SYNC.
The only difference between the modes starting with
CCLK and those starting with UCLK is that for the
UCLK modes, a user clock must be supplied to the
start-up logic. The timing of start-up events is then
based upon this user clock, rather than CCLK. The dif-
ference between the SYNC and NOSYNC modes is
that fo r SYNC mode, the timing of two of the start-up
e vents, release of the set/reset of internal FFs, and the
I/Os becoming active is triggered by the rise of the
e xternal DONE pin f ollowed b y a variable number of ris-
ing clock edges (either CCLK or UCLK). For the
NOSYNC mode, the timing of these two events is
based only on either CCLK or UCLK.
DONE is an open-drain bidirectional pin that may
include an optional (enab led by default) pull-up resistor
to accommodate wired ANDing. The open-drain DONE
signals from multiple FPGAs can be tied together
(ANDed) with a pull-up (internal or external) and used
as an active-high ready signal, an active-low PROM
enable, or a reset to other portions of the system.
When used in SYNC mode, these ANDed DONE pins
can be used to synchronize the other two start-up
events, since they can all be synchronized to the same
external signal. This signal will not rise until all FPGAs
release their DONE pins, allowing the signal to be
pulled high.
The default for
ORCA
is the CCLK_SYNC synchro-
nized start-up mode where DONE is released on the
first CCLK rising edge, C1 (see Figure 51). Since this is
a synchronized start-up mode, the open-drain DONE
signal can be held low e xternally to stop the occurrence
of the other two start-up events. Once the DONE pin
has been released and pulled up to a high level, the
other two start-up events can be programmed individu-
ally to either happen immediately or after up to four ris-
ing edges of CCLK (Di, Di + 1, Di + 2, Di + 3, Di + 4).
The default is for both events to happen immediately
after DONE is released and pulled high.
A commonly used design technique is to release
DONE one or more clock cycles bef ore allowing the I/O
to become active. This allows other configuration
devices, such as PR OMs, to be disconnected using the
DONE signa l so that there is no bus contention when
the I/Os become active. In addition to controlling the
FPGA during start-up, other start-up techniques that
avoid contention include using isolation devices
between the FPGA and other circuits in the system,
reassigning I/O locations, and maintaining I/Os as 3-
stated outputs until contentions are resolved.
Each of these start-up options can be selected during
bit stream generation in
ORCA
Foundry, using
Advanced Options. For more information, please see
the
ORCA
Foundry docume ntati on .
8888 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
FPGA States of Operation (continued)
Note: F = finished, no more CLKs required. 5-2761(F)
Figure 51. Start-Up Waveforms
Reconfiguration
To reconfigure the FPGA when the de vice is operating
in the system, a low pulse is input into PRGM. The con-
figuration data in the FPGA is cleared, and the I/Os not
used for configuration are 3-stated. The FPGA then
samples the mode select inputs and begins reconfigu-
ration. When reconfiguration is complete, DONE is
released, allowing it to be pulled high.
Par t i a l R e configuration
All
ORCA
device families have been designed to allow
a partial reconfiguration of the FPGA at any time. This
is done by setting a bit stream option in the previous
configuration sequence that tells the FPGA to not reset
all of the configuration RAM during a reconfiguration.
Then only the configuration frames that are to be modi-
fied need to be rewritten, thereby reducing the configu-
ration time.
Other bit stream options are also available that allow
one portion of the FPGA to remain in operation while a
partial reconfigur ation is being done. If this is done, the
user must be careful to not cause contention between
the two configurations (the bit stream resident in the
FPGA and the partial reconfiguration bit stream) as the
seco nd reco nfig urati on bit stre am is being loa ded .
Othe r Conf iguration Options
There are many other configuration options av ailable to
the us er that ca n be se t during bit st rea m gen er ati on in
ORCA
Foundry. These include options to enable
boundary scan and/or the microprocessor interface
(MPI) and/or the programmable clock manager (PCM),
readback options, and options to control and use the
internal oscillator after configuration.
Other useful options that affect the next configuration
(not the current configuration process) include options
to disable the global set/reset during configuration, dis-
able the 3-state of I/Os during configuration, and dis-
able the reset of internal RAMs during configuration to
allow f or partial configurations (see above). For more
information on how to set these and other configuration
options, please see the
ORCA
Foundry documenta-
tion.
Di
C1 C2 C3 C4
F
C1 C2 C3 C4
C1 C2 C3 C4
C1, C2, C3, OR C4
Di + 1Di Di + 2 Di + 3 Di + 4
Di + 1Di Di + 2 Di + 3 Di + 4
CCLK_SYNC
DONE IN
U1 U2 U3 U4
F
U1 U2 U3 U4
U1 U2 U3 U4
UCLK_NOSYNC
Di + 1Di Di + 2 Di + 3 Di + 4
Di + 1 Di + 2 Di + 3
UCLK_SYNC
UCLK PERIOD
SYNCHRONIZATION UNCERTAINTY
DONE IN
F
C1
C1 U1, U2, U3, OR U4
DONE
I/O
GSRN
ACTIVE
DONE
I/O
GSRN
ACTIVE
DONE
I/O
GSRN
ACTIVE
DONE
I/O
GSRN
ACTIVE
UCLK
F
CCLK_NOSYNC
Lucent Technologies Inc. 89
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Configuration Data Format
The
ORCA
Foundry Development System interfaces
with front-end design entry tools and provides tools to
produce a fully configured FPGA. This section dis-
cusses using the
ORCA
F oundry De velopment System
to generate configuration RAM data and then provides
the details of the configuration frame format.
The
ORCA
OR3Cxx and OR3Txxx Series FPGAs are
bit stream compatible.
Using
ORCA
Foundry to Generate
Configuration RAM Data
The configuration data bit stream defines the I/O func-
tionality, logic, and interconnections within the FPGA.
The bit stream is generated by the dev elopment sys-
tem. The bit stream created by the bit stream genera-
tion tool is a series of 1s and 0s used to write the FPGA
configuration RAM. It can be loaded into the FPGA
using one of the configuration modes discussed later.
In the bit stream generator, the designer selects
options that aff ect the FPGA’s functionality. Using the
output of the bit stream generator, circuit_name.bit,
the development system’s download tool can load the
configuration data into the
ORCA
series FPGA evalua-
tion board from a PC or workstation.
Alternatively, a user can program a PROM (such as a
Serial ROM or a standard EPR OM) and load the FPGA
from the PROM. The development system’s PROM
programming tool produces a file in .mks or .e xo for-
mat.
Config uration D ata Fram e
Configuration data can be presented to the FPGA in
two frame f ormats: autoincrement and explicit. A
detailed description of the frame formats is shown in
Figure 52, Figure 53, and Table 32. The two modes are
similar except that autoincrement mode uses assumed
address incrementation to reduce the bit stream size ,
and explicit mode requires an address for each data
frame. In both cases, the header frame begins with a
series of 1s and a preamble of 0010, followed by a
24-bit length count field representing the total number
of configuration clocks needed to complete the loading
of the FPGAs.
Following the header frame is a mandatory ID frame.
(Note that the ID frame was optional in the
ORCA
2C
and 2C/TxxA Series.)
The ID frame contains data used to determine if the bit
stream is being loaded to the correct type of
ORCA
FPGA (i.e., a bit stream generated for an OR3C55 is
being sent to an OR3C55). Error checking is always
enabled f or Series 3 devices, through the use of an
8-bit checksum. One bit in the ID frame also selects
between the autoincrement and explicit address modes
for this load of the configuration data.
A configuration data frame follows the ID frame. A data
frame starts with a 01-start bit pair and ends with
enough 1-stop bits to reach a byte boundary. If using
autoincrement configuration mode, subsequent data
frames can follow. If using explicit mode, one or more
address frames must follow each data frame, telling the
FPGA at what addresses the preceding data frame is
to be stored (each data frame can be sent to multiple
addresses).
Following all data and address frames is the postam-
ble. The format of the postamble is the same as an
address frame with the highest possible address value
with the checksum set to all ones.
90 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Configuration Data Format (continued)
5-5759(F)
Figure 52. Serial Configuration Data Format—Autoincrement Mode
5-5760(F)
Figure 53. Serial Configuration Data Format—Explicit Mode
Table 32. Confi
g
uration Frame Format and Contents
* In MPI confi
g
uration mode, the number of stop bits = 32.
Note: For slave parallel mode, the b
y
te containin
g
the preamble must be 11110010. The number of leadin
g
header dumm
y
bits must
be
(
n * 8
)
+ 4, where n is an
y
nonne
g
ative inte
g
er and the number of trailin
g
dumm
y
bits must be
(
n * 8
)
, where n is an
y
positive
inte
g
er. The number of stop bits/frame for slave parallel mode must be
(
x * 8
)
, where x is a positive inte
g
er. Note also that the bit
stream
g
enerator tool supplies a bit stream that is compatible with all confi
g
uration modes, includin
g
slave parallel mode.
Header 11110010 Preamble
24-bit Len
g
th Count Confi
g
uration frame len
g
th.
11111111 Trailin
g
header—8 bits.
ID Frame
0101 1111 1111 1111 ID frame header.
Confi
g
uration Mode 00 = autoincrement, 01 = explicit.
Reserved
[
41:0
]
Reserved bits set to 0.
ID 20-bit part ID.
Checksum 8-bit checksum.
11111111 Ei
g
ht stop bits
(
hi
g
h
)
to separate frames.
Confi
g
uration
Data
Frame
(
repeated for each
data frame
)
01 Data frame header.
Data Bits Number of data bits depends upon device.
Ali
g
nment Bits = 0 Strin
g
of 0 bits added to bit stream to make frame header, plus data
bits reach a b
y
te boundar
y
.
Checksum 8-bit checksum.
11111111 Ei
g
ht stop bits
(
hi
g
h
)
to separate frames.
Confi
g
uration
Address
Frame
00 Address frame header.
14 Address Bits 14-bit address of location to start data stora
g
e.
Checksum 8-bit checksum.
11111111 Ei
g
ht stop bits
(
hi
g
h
)
to separate frames.
Postamble 00 Postamble header.
11111111 111111 Dumm
y
address.
1111111111111111 16 stop bits.*
CONFIGURATION DATA CONFIGURATION DATA
10 01 01
PREAMBLE LENGTH ID FRAME CONFIGURATION CONFIGURATION POSTAMBLE
CONFIGURATION HEADER
00 00
COUNT DATA FRAME 1 DATA FRAME 2
PREAMBLE LENGTH ID FRAME CONFIGURATION CONFIGURATION POSTAMBLE
CONFIGURATION HEADER
ADDRESS ADDRESS
00
COUNT DATA FRAME 1 DATA FRAME 2 FRAME 2FRAME 1
CONFIGURATION DATA CONFIGURATION DATA
10 01 0100 0000
Lucent Technologies Inc. 91
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Configuration Data Format (continued)
The length and number of data frames and information on the PROM size for the Series 3 FPGAs are given in
Table 33.
Table 33. Confi
g
uration Frame Size
Bit Stream Error Checking
There are three different types of bit stream error checking performed in the
ORCA
Series 3 FPGAs:
ID frame, frame alignment, and CRC checking.
The ID data frame is sent to a dedicated location in the FPGA. This ID frame contains a unique code for the de vice
for which it was generated. This device code is compared to the internal code of the FPGA. Any differences are
flagged as an ID error. This frame is automatically created by the bit stream generation progr am in
ORCA
F oundry.
Each data and address frame in the FPGA begins with a frame start pair of bits and ends with eight stop bits set to
1. If any of the previous stop bits were a 0 when a frame start pair is encountered, it is flagged as a frame align-
ment error.
Error chec king is also done on the FPGA for each frame by means of a checksum byte. If an error is f ound on e val-
uation of the checksum byte, then a checksum/parity error is flagged. The checksum is the XOR of all the data
bytes, from the start of frame up to and including the b ytes before the chec ksum. It applies to the ID, address, and
data frames.
When any of the three possible errors occur, the FPGA is forced into an idle state, forcing INIT low. The FPGA will
remain in this state until either the RESET or PRGM pins are asserted.
If using either of the MPI modes to configure the FPGA, the specific type of bit stream error is written to one of the
MPI registers by the FPGA configuration logic. The PGRM bit of the MPI control register can also be used to reset
out of the error condition and restart configuration.
Devices OR3T20 OR3T30 OR3C/T55 OR3C/T80 OR3T125
# of Frames 856 984 1240 1496 1880
Data Bits/Frame 202 232 292 352 442
Confi
g
uration Data
(
# of fram es x # of data
bits/frame
)
172,912 228,288 362,080 526,592 830,960
Maximum Total # Bits/Frame
(
ali
g
n bits, 01
frame start, 8-bit checksum, 8 stop bits
)
224 256 312 376 464
Maxi mum Confi
g
uratio n Data
(
# bits/ frame
x # of frames
)
191,744 251,904 386,880 562,496 872,320
Maximum PROM Size
(
bits
)
(
add confi
g
uration header and postamble
)
191,912 252,072 387,048 562,664 872,488
9292 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
FPGA Configuration Modes
There are eight methods for configuring the FPGA.
Seven of the configuration modes are selected on the
M0, M1, and M2 inputs. The eighth configuration mode
is accesse d through the boun dary-scan inte r face. A
fourth input, M3, is used to select the frequency of the
internal oscillator, which is the source for CCLK in
some configuration modes . The nominal frequencies of
the internal oscillator are 1.25 MHz and 10 MHz. The
1.25 MHz frequency is selected when the M3 input is
unconnected or driven to a high state.
There are three basic FPGA configuration modes:
master, slave, and peripheral. The configuration data
can be transmitted to the FPGA serially or in parallel
bytes. As a master, the FPGA provides the control sig-
nals out to strobe data in. As a slave device, a clock is
generated externally and provided into the CCLK input.
In the three peripheral modes, the FPGA acts as a
microprocessor peripheral. Table 34 lists the functions
of the configuration mode pins. Note that two configura-
tion modes previously available on the OR2Cxx and
OR2C/TxxA devices (master parallel down and syn-
chronous peripheral) have been removed for Series 3
devices.
Table 34. Confi
g
uration Modes
*
Motorola
is a re
g
istered trademark of Motorola, Inc.
Master Parallel Mode
The master parallel configuration mode is generally
used to interface to industry-standard, byte-wide mem-
ory, such as the 2764 and larger EPROMs. Figure 54
provides the connections f or master parallel mode. The
FPGA outputs an 18-bit address on A[17:0] to memory
and reads 1 byte of configuration data on the rising
edge of RCLK. The parallel bytes are internally serial-
ized starting with the least significant bit, D0. D[7:0] of
the FPGA can be connected to D[7:0] of the micropro-
cessor only if a standard prom file format is used. If a
.bit or .rbt file is used from
ORCA
Foundry, then the
user must mirror the bytes in the .bit or .rbt file OR
leave the .bit or .rbt file unchanged and connect D[7:0]
of the FPGA to D[0:7] of the microprocessor.
Figure 54. Master Parallel Configuration Schematic
In master parallel mode, the starting memory address
is 00000 Hex, and the FPGA increments the address
for each byte loaded.
One master mode FPGA can interface to the memory
and provide configuration data on DOUT to additional
FPGAs in a daisy-chain. The configuration data on
DOUT is provided synchronously with the falling edge
of CCLK. The frequency of the CCLK output is eight
times that of RCLK.
M2 M1 M0 CCLK Confi
g
uration
Mode Data
0 0 0 Output Master Serial Serial
0 0 1 Input Slave Paral le l Paral le l
0 1 0 Output Microprocessor:
Motorola
*
Pow-
erPC
Parallel
0 1 1 Output Microprocessor:
Intel i96 0
Parallel
1 0 0 Output Master Parallel Parallel
101OutputAs
y
nc Peripheral Parallel
110 Reserved
1 1 1 Input Slave Seri al Seri al
EPROM
A[17:0]
DONE
M2
M1
M0
HDC
ORCA
SERIES
FPGA
RCLK
LDC
VDD
D[7:0]
DOUT
CCLK
TO DAISY-
CHAINED
DEVICES
VDD OR GND
PRGMPROGRAM
A[17:0]
D[7:0]
OE
CE
Lucent Technologies Inc. 93
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
FPGA Configuration Modes (continued)
Master Serial Mode
In the master serial mode, the FPGA loads the configu-
ration data from an e xternal serial ROM. The configura-
tion data is either loaded automatically at start-up or on
a PRGM command to reconfigure. The ATT1700A
Series Serial PROMs can be used to configure the
FPGA in the master serial mode. This provides a sim-
ple 4-pin interface in a compact package.
Configuration in the master serial mode can be done at
powerup and/or upon a configure command. The sys-
tem or the FPGA must activate the serial ROM's
RESET/OE and CE inputs. At powerup, the FPGA and
serial ROM each contain internal power-on reset cir-
cuitry that allows the FPGA to be configured without
the system providing an external signal. The power-on
reset circuitry causes the serial ROM's internal address
pointer to be reset. After powerup, the FPGA automati-
cally enters its initialization phase.
The serial ROM/FPGA interf ace used depends on such
factors as the availability of a system reset pulse, avail-
ability of an intelligent host to generate a configure
command, whether a single serial ROM is used or mul-
tiple serial ROMs are cascaded, whether the serial
ROM contains a single or multiple configuration pro-
grams, etc. Because of differing system requirements
and capabilities, a single FPGA/serial ROM interf ace is
generally not appropriate for all applications.
Data is read in the FPGA sequentially from the serial
ROM. The DATA output from the serial ROM is con-
nected directly into the DIN input of the FPGA. The
CCLK output from the FPGA is connected to the CLK
input of the serial ROM. During the configuration pro-
cess, CCLK cloc ks one data bit on each rising edge.
Since the data and clock are direct connects, the
FPGA/serial ROM design task is to use the system or
FPGA to enable the RESET/OE and CE of the serial
ROM(s). There are se veral methods for enabling the
serial ROM’s RESET/OE and CE inputs. The serial
ROM’s RESET/OE is programmable to function with
RESET active-high and OE act ive-low or RESET active-
low and OE activ e-high.
In Figure 55, serial ROMs are cascaded to configure
multiple daisy-chained FPGAs. The host generates a
500 ns low pulse into the FPGA's PRGM input. The
FPGA’s INIT input is connected to the serial ROMs’
RESET/OE input, which has been programmed to
function with RESET active-low and OE active-high.
The FPGA DONE is routed to the CE pin. The low on
DONE enables the serial ROMs. At the completion of
configuration, the high on the FPGA's DONE disables
the serial ROM.
Serial ROMs can also be cascaded to support the con-
figuration of multiple FPGAs or to load a single FPGA
when configuration data requirements exceed the
capacit y of a single serial ROM. After the last bit from
the first serial ROM is read, the serial ROM outputs
CEO low and 3-states the DATA output. The next serial
ROM recogniz es the low on CE input and outputs con-
figuration data on the DATA output. After configuration
is complete, the FPGA’s DONE output into CE disab les
the serial ROMs.
This FPGA/serial RO M interface is not used in applica-
tions in which a serial ROM stores multiple configura-
tion programs. In these applications, the next
configuration program to be loaded is stored at the
ROM location that f ollows the last address for the previ-
ous configuration program. The reason the interface in
Figure 55 will not work in this application is that the low
output on the INIT signal would reset the serial ROM
address pointer, causing the first configuration to be
reloaded.
In some applications, there can be contention on the
FPGA's DIN pin. During configuration, DIN receives
configuration data, and after configuration, it is a user
I/O. If there is contention, an early DONE at start-up
(selected in
ORCA
Foundry) may correct the problem.
An alternative is to use LDC to drive the serial ROM's
CE pin. In order to reduce noise, it is generally better to
run the master serial configuration at 1.25 MHz (M3 pin
tied high), rather than 10 MHz, if possible.
Figure 55. Master Serial Configuration Schematic
ATT1700A
DIN
M2
M1
M0
ORCA
SERIES
FPGA
CCLK
DOUT
TO D AI SY-
CHAINED
DEVICES
DATA
CLK
CE
CEO
ATT1700A
DATA
CLK
RESET
/OE
CEO
CE
TO MORE
SERIAL ROMs
AS NEEDED
DONE
INIT
PROGRAM
RESET
/OE
PRGM
5-4456.1(F)
9494 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
FPGA Configuration Modes (continued)
Asynchr onous Peripheral Mode
Figure 56 shows the connections needed for the asyn-
chronous peripheral mode. In this mode, the FPGA
system interface is similar to that of a microprocessor-
peripheral interface. The microprocessor generates the
control signals to write an 8-bit byte into the FPGA. The
FPGA control inputs include active-low CS0 and active-
high CS1 chip selects and WR and RD inputs. The chip
selects can be cycled or maintained at a static level
during the configuration cycle. Each byte of data is writ-
ten into the FPGA’s D[7:0] input pins. D[7:0] of the
FPGA can be connected to D[7:0] of the microproces-
sor only if a standard prom file f ormat is used. If a .bit or
.rb t file is us ed from
ORCA
F oundry, then the user must
mirror the bytes in the .bit or .rbt file OR leav e the .bit or
.rbt file unchanged and connect D[7:0] of the FPGA to
D[0:7] of the microprocessor.
The FPGA prov ides an RDY/BUSY status output to indi-
cate that another byte can be loaded. A low on RDY/
BUSY indicates that the double-buffered hold/shift reg-
isters are not ready to receive data, and this pin must
be monitored to go high before another byte of data
can be written. The shortest time RDY/BUSY is low
occurs when a byte is loaded into the hold register and
the shift register is empty, in which case the byte is
immediately transferred to the shift register. The long-
est time for RDY/BUSY to remain low occurs wh en a
byte is loaded into the holding register and the shift
register has just started shifting configuration data into
configuration RAM.
The RDY/BUSY status is also av ailable on the D7 pin by
enabling the chip selects, setting WR high, and apply-
ing RD low, where the RD input provides an output
enable for the D7 pin when RD is low. The D[6:0] pins
are not enab led to drive when RD is low and, therefore ,
only act as input pins in asynchronous peripheral
mode. Optionally, the user can ignore the RDY/BUSY
status and simply wait until the maximum time it would
take for the RDY/BUSY line to go high, indicating the
FPGA is ready for more data, before writing the next
data byte.
Figure 56. Asynchr onous P eripheral Configuration
Micr oprocessor Interface (MPI) Mode
The built-in MPI in Series 3 FPGAs is designed for use
in configuring the FPGA. Figure 57 and Figure 58 show
the glueless interface for FPGA configuration and read-
back from the
PowerPC
and
i960
processors, respec-
tively. When enabled by the mode pins, the MPI
handles all configuration/readback control and hand-
shaking with the host processor. For single FPGA con-
figuration, the host sets the configuration control
register PRGM bit to zero then back to a one and, after
reading that the INIT signal is high in the MPI status
register, transfers data 8 bits at a time to the FPGA’s
D[7:0] input pins.
If configuring multiple FPGAs through daisy-chain
operation is desired, the MP_DAISY bit must be set in
the configuration control register of the MPI. Because
of the latency inv olved in a daisy-chain configuration,
the MP_HOLD_BUS bit may be set to zero rather than
one for daisy-chain operation. This allows the MPI to
acknowledge the data transfer before the configuration
information has been serialized and transferred on the
FPGA daisy-chain. The early acknowledgment frees
the host processor to perform other system tasks. Con-
figuring with the MP_HOLD_BUS bit at zero requires
that the host microprocessor poll the RDY/BUSY bit of
the MPI status register and/or use the MPI interrupt
capability to confirm the readiness of the MPI for more
configuration data.
MICRO-
PROCESSOR
D[7:0]
CS1
M2
M1
M0
HDC
ORCA
SERIES
FPGA
8
LDC
VDD
DONE
CS0
DOUT
CCLK
TO DAISY-
CHAINED
DEVICES
BUS
CONTROLLER
ADDRESS
DECODE LOGIC
RD
WR
RDY/BUSY
INIT
PRGM
Lucent Technologies Inc. 95
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
FPGA Configuration Modes (continued)
There are two options for using the host interrupt
request in configuration mode. The configuration con-
trol register off ers control bits to enable the interrupt on
either a bit stream error or to notify the host processor
when the FPGA is ready for more configurat ion data.
The MPI status register ma y be used in conjunction
with, or in place of, the interrupt request options. The
status register contains a 2-bit field to indicate the bit
stream error status. As previously mentioned, there is
also a bit to indicate the MPI’s readiness to receive
another byte of configuration data. A flow chart of the
MPI configuration process is shown in Figure 59. The
MPI status and configuration register bit maps can be
found in the Special Function Blocks section and MPI
configuration timing information is available in the Tim-
ing Characteristics section of this data sheet.
5-5761(F)
Note: FPGA shown as a memor
y
-mapped peripheral usin
g
CS0 and
CS1. Other decodin
g
schemes are possible usin
g
CS0 and/or
CS1.
Figure 57.
PowerPC
/MPI C onf i g u r a t io n Sc he m at i c
5-5762(F)
Note: FPGA shown as onl
y
s
y
stem peripheral with fixed chip select
si
g
nals. For multiperipheral s
y
stems, address decodin
g
and/
or latchin
g
can be used to implement chip selects.
Figure 58.
i960
/MPI Configuration Schematic
Configuration readback can also be performed via the
MPI when it is in user mode. The MPI is enabled in user
mode by setting the MP_USER bit to 1 in the configura-
tion control register prior to the start of configuration or
through a configuration option. To perform readback,
the host processor writes the 14-bit readback start
address to the readbac k address registers and sets the
RD_CFG bit to 0 in the configuration control register.
Readback data is returned 8 bits at a time to the read-
back data register and is valid when the DATA_RDY bit
of the status register is 1. There is no error checking
during readback. A flow chart of the MPI readback
operation is shown in Figure 60. The RD_DATA pin
used for dedicated FPGA readback is invalid during
MPI readback.
5-5763(F)
Figure 59. Configuration Through MPI
DOUT
CCLK
D[7:0]
A[4:0]
MPI_CLK
MPI_RW
MPI_ACK
MPI_BI
MPI_IRQ
MPI_STRB
CS0
CS1 HDC
LDC
D[7:0]
A[27:31]
CLKOUT
RD/WR
TA
BI
IRQx
TS
A26
A25
TO DAISY-
CHAINED
DEVICES
POWERPC ORCA
8
FPGA
SERIES 3
DONE
INIT
DOUT
CCLK
D[7:0]
MPI_CLK
MPI_RW
MPI_ACK
MPI_IRQ
MPI_ALE
MPI_BE1
HDC
LDC
TO DA ISY-
CHAINED
DEVICES
ORCA
8
FPGA
SERIES 3
DONE
INIT
AD[7:0]
CLKIN
W/R
RDYRCV
XINTx
ALE
BE1
i960
CS1
CS0
i960
SYSTEM CLOCK
V
DD
MPI_BE0
BE0 MPI_STRB
ADS
POWER ON WITH
WRITE CONFIGURATION
READ STATUS REGISTER
INIT = 1? NO
READ STATUS REGISTER
BIT STREAM ERROR?
DATA_RDY = 1?
WRITE DATA TO
DONE = 1?DONE
ERROR
YES
YES
YES
NO
NO
YES
NO
VALID M[3:0]
CONTROL REGISTER BITS
CONFIGURATION DATA REG
96 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
FPGA Configuration Modes (continued)
5-5764(F)
Figure 60. Readback Through MPI
ENABLE MICROPROCESS O R
SET READBA CK ADDRESS
WRITE RD_CFG TO 0
DATA_RDY = 1?
READ DATA REGISTER
START OF FRAME
DATA = 0xFF?
YES
YES
READ STATUS REGISTER
IN CONTROL REGISTER 1
INTERFACE IN USER MODE
READ DATA REGISTER
FOUND?
READ UNTIL END OF FRAME
FINISHED
READBACK?
YES
YES
WRITE RD_CFG
CONTROL
STOP NO
NO
ERROR
NO
ERROR
NO
READ DATA REGISTER
DATA = 0xFF?
YES
NO
ERROR
TO 1 IN
REGISTER 1
Lucent Technologies Inc. 97
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
FPGA Configuration Modes (continued)
Slave Serial Mode
The slave serial mode is primarily used when multiple
FPGAs are configured in a daisy-chain (see the Daisy-
Chaining section). It is also used on the FPGA evalua-
tion board that interfaces to the download cable. A
de vice in the slave serial mode can be used as the lead
device in a daisy-chain. Figure 61 shows the connec-
tions for the slave serial configuration mode.
The configuration data is provided into the FPGA’ s DIN
input synchronous with the configuration clock CCLK
input. After the FPGA has loaded its configuration data,
it retransmits the incoming configuration data on
DOUT. CCLK is routed into all slave serial mode
devices in parallel.
Multiple sla ve FPGAs can be loaded with identical con-
figurations simultaneously. This is done by loading the
configuration data into the DIN inputs in parallel.
5-4485(F)
Figure 61. Slave Serial Configuration Schematic
Slave Parallel Mode
The slave parallel mode is essentially the same as the
slav e serial mode e xcept that 8 bits of data are input on
pins D[7:0] for each CCLK cycle. Due to 8 bits of data
being input per CCLK cycle, the DOUT pin does not
contain a valid bit stream for slave parallel mode. As a
result, the lea d device cannot be used in the slave
parallel mode in a daisy-chain configuration.
Figure 62 is a schematic of the connections for the
slave parallel configuration mode. WR and CS0 are
active-low chip select signals, and CS1 is an active-
high chip select signal. These chip selects allow the
user to configure multiple FPGAs in slave parallel
mode using an 8-bit data bus common to all of the
FPGAs. These chip selects can then be used to select
the FPGA(s) to be configured with a given bit stream.
The chip sele cts must be active for each valid CCLK
cycle until the device has been completely pro-
grammed. They can be inactiv e between cycles but
must meet the setup and hold times for each valid pos-
itive CCLK. D[7:0] of the FPGA can be connected to
D[7:0] of the microprocessor only if a standard prom
file format is used. If a .bit or .rbt file is used from
ORCA
Foundry, then the user must mirror the bytes in
the .bit or .rbt file OR leav e the .bit or .rbt file
unchanged and connect D[7:0] of the FPGA to D[0:7]
of the microprocessor.
5-4487(F)
Figure 62. Slave Parallel Configuration Schematic
MICRO-
PROCESSOR
OR
DOWNLOAD
CABLE
M2
M1
M0
HDC
SERIES
FPGA
LDC
VDD
CCLK
PRGM
DOUT
TO DAISY-
CHAINED
DEVICES
DONE
DIN
INIT
ORCA
MICRO-
PROCESSOR
OR
SYSTEM
D[7:0]
DONE
CCLK
CS1
M2
M1
M0
HDC
LDC
8
VDD
INIT
PRGM
CS0
WR
SERIES
FPGA
ORCA
9898 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
FPGA Configuration Modes (continued)
Daisy-Chaining
Multiple FPGAs can be configured by using a daisy-
chain of the FPGAs. Daisy-chaining uses a lead FPGA
and one or more FPGAs configured in slave serial
mode. The lead FPGA can be configured in any mode
e xcept slav e parallel mode. (Daisy-chaining is a vailable
with the boundary-scan ram_w instruction discussed
later.)
All daisy-chained FPGAs are connected in series.
Each FPGA reads and shifts the preamble and length
count in on positive CCLK and out on negative CCLK
edges.
An upstream FPGA that has received the preamble
and length count outputs a high on DOUT until it has
received the appropriate number of data frames so that
downstream FPGAs do not receive frame start bit
pairs. After loading and retransmitting the preamble
and length count to a daisy-chain of slave devices, the
lead device loads its configuration data frames.
The loading of configuration data continues after the
lead device has received its configuration data if its
internal frame bit counter has not reached the length
count. When the configuration RAM is full and the num-
ber of bits received is less than the length count field,
the FPGA shifts any additional data out on DOUT.
The configuration data is read into DIN of slav e de vices
on the positive edge of CCLK, and shifted out DOUT
on the negative edge of CCLK. Figure 63 shows the
connections for loading multiple FPGAs in a daisy-
chain configuration.
The generation of CCLK for the daisy-chained devices
that are in slave serial mode differs depending on the
configuration mode of the lead device. A master paral-
lel mode device uses its internal timing generator to
produce an internal CCLK at eight times its memory
address rate (RCLK). The asynchronous peripheral
mode device outputs eight CCLKs for each write cycle.
If the lead device is configured in slave mode, CCLK
must be routed to the lead device and to all of the
daisy-chained devices.
5-4488(F
Figure 63. Daisy-Chain Configuration Schematic
As seen in Figure 63, the INIT pins for all of the FPGAs are connected together. This is required to guarantee that
powerup and initialization will work correctly. In general, the DONE pins for all of the FPGAs are also connected
together as shown to guarantee that all of the FPGAs enter the start-up state simultaneously. This may not be
required, depending upon the start-up sequence desired.
VDD
EPROM
PROGRAM
D[7:0]
OE
CE
A[17:0] A[17:0]
D[7:0]
DONE
M2
M1
M0
DONE
HDC
LDC
RCLK
CCLK
DOUT DIN DOUT DIN
CCLK
DONE
DOUT
INIT INIT INIT
CCLK
VDD
VDD OR
GND
PRGM PRGM
M2
M1
M0
PRGM
M2
M1
M0
VDD VDD
HDC
LDC
RCLK
HDC
LDC
RCLK
VDD
ORCA
SERIES
FPGA
SLAVE #2
ORCA
SERIES
FPGA
MASTER
ORCA
SERIES
FPGA
SLAVE #1
Lucent Technologies Inc. 99
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
FPGA Configuration Modes (continued)
Daisy-Chaining with Boundary Scan
Multiple FPGAs can be configured through the JTAG ports by using a daisy-chain of the FPGAs. This daisy-chain-
ing operation is available upon initial configuration after powerup, after a power-on reset, after pulling the program
pin to reset the chip, or during a reconfiguration if the EN_JTAG RAM has been set.
All daisy-chained FPGAs are connected in series. Each FPGA reads and shifts the preamble and length count in
on the positive TCK and out on the negative TCK edges.
An upstream FPGA that has received the preamble and length count outputs a high on TDO until it has received
the appropriate number of data frames so that downstream FPGAs do not receive frame start bit pairs. After load-
ing and retransmitting the preamble and length count to a daisy-chain of downstream devices, the lead device
loads its configuration data frames.
The loading of configuration data continues after the lead device had received its configuration read into TDI of
downstream devices on the positive edge of TCK, and shifted out TDO on the negative edge of TCK. Figure 63
shows the connections for loading multiple FPGAs in a JTAG daisy-chain configuration.
100 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are abso-
lute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess
of those given in the operations sections of this data sheet. Exposure to absolute maximum ratings for extended
periods can adversely affect device reliability.
The
ORCA
Series FPGAs include circuitry designed to protect the chips from damaging substrate injection cur-
rents and to prevent accumulations of static charge. Nevertheless, conventional precautions should be observ ed
during storage, handling, and use to avoid exposure to excessive electrical stress.
Table 35. Absolute Maximum Ratings
Recommended Operating Conditions
Table 36. Recommended Operating Conditions
Note: The maximum recommended
j
unction temperature
(
TJ
)
durin
g
operation is 125 °C.
Parameter S
y
mbol Min Max Unit
Stora
g
e Temperature Tst
g
–65 150 °C
Suppl
y
Volta
g
e with Respect to Ground VDD –0.5 7.0 V
Input Si
g
nal with Respect to Ground — –0.5 VDD + 0.3 V
Si
g
nal Applied to Hi
g
h-impedance Output — –0.5 VDD + 0.3 V
Maximum Packa
g
e Bod
y
Temperature — — 220 °C
Mode
OR3Cxx OR3Txxx
Tem
p
erature
Ran
g
e
(
Ambient
)
Su
pp
l
y
Volta
g
e
(
VDD
)
Tem
p
erature
Ran
g
e
(
Ambient
)
Su
pp
l
y
Volta
g
e
(
VDD
)
Commercial 0 °C to 70 °C 5 V ± 5% 0 °C to 70 °C 3.0 V to 3.6 V
Industrial –40 °C to +85 °C 5 V ± 10% –40 °C to +85 °C 3.0 V to 3.6 V
Lucent Technologies Inc. 101
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Electrical Characteristics
Table 37. Electrical Characteristics
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Parameter S
y
m-
bol Test Conditions OR3Cxx OR3Txxx Unit
Min Max Min Max
Input Volta
g
e:
Hi
g
h
Low VIH
VIL
Input confi
g
ured as CMOS
(
includes OR3Txxx
)
50% VDD
GND – 0.5 VDD + 0.5
20% VDD 50% VDD
GND – 0.5 VDD + 0.5
30% VDD V
V
Input Volta
g
e:
Hi
g
h
Low VIH
VIL
OR3Txxx 5 V Tolerant —
——
—50% VDD
GND – 0.5 5.8 V
30% VDD V
V
Input Volta
g
e:
Hi
g
h
Low VIH
VIL
Input confi
g
ured as TTL
(
not valid for OR3Txxx
)
2.0
–0.5 VDD + 0.3
0.8 —
— —
—V
V
Output Volta
g
e:
Hi
g
h
Low VOH
VOL VDD = min, IOH = 6 mA or 3 mA
VDD = min, IOL = 12 mA or 6 mA 2.4
——
0.4 2.4
——
0.4 V
V
Input Leaka
g
e Current ILVDD = max, VIN = VSS or VDD –10 10 –10 10
µ
A
Standb
y
Current:
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
IDDSB OR3Cxx
(
TA = 25 °C,
VDD = 5.0 V
)
OR3Txxx
(
TA = 25 °C,
VDD = 3.3 V
)
internal oscillator runnin
g
, no out-
put loads, inputs VDD or GND
(
after confi
g
uration
)
—
—
—
—
—
—
—
4.06
4.56
—
—
—
—
—
—
4.70
4.90
5.30
5.80
6.70
mA
mA
mA
mA
mA
Standb
y
Current:
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
IDDSB OR3Cxx
(
TA = 25 °C,
VDD = 5.0 V
)
OR3Txxx
(
TA = 25 °C,
VDD = 3.3 V
)
internal oscillator stopped, no
output loads, inputs VDD or GND
(
after confi
g
uration
)
—
—
—
—
—
—
—
3.05
3.42
—
—
—
—
—
—
3.52
3.68
3.98
4.35
5.02
mA
mA
mA
mA
mA
Powerup Current:
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
Ipp Power suppl
y
current @ approxi-
matel
y
1 V, within a recommended
power suppl
y
ramp rate of
1 ms—200 ms
—
—
3.2
5.4
—
—
—
—
—
—
1.2
1.6
2.7
4.0
6.5
—
—
—
—
—
mA
mA
mA
mA
mA
Data Retention Volta
g
eV
DR TA = 25 °C 2.3 — 2.3 — V
Input Capacitance CIN OR3Cxx
(
TA = 25 °C,
VDD = 5.0 V
)
OR3Txxx
(
TA = 25 °C,
VDD = 3.3 V
)
Test fre
q
uenc
y
= 1 MHz
—9—8pF
Output Capacitance COUT OR3Cxx
(
TA = 25 °C,
VDD = 5.0 V
)
OR3Txxx
(
TA = 25 °C,
VDD = 3.3 V
)
Test fre
q
uenc
y
= 1 MHz
—9—8pF
102 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Electrical Characteristics (continued)
Table 37. Electrical Characteristics (continued)
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
* On the OR3Txxx devices, the pull-up resistor will externall
y
pull the pin to a level 1.0 V below VDD.
Note: For 3T devices driven to 5 V.
Parameter S
y
mbol Test Conditions OR3Cxx OR3Txxx Unit
Min Max Min Max
DONE Pull-up
Resistor* RDONE — 100 — 100 — kΩ
M
[
3:0
]
Pull-up
Resistors* RM— 100 — 100 — kΩ
I/O Pad Static Pull-up
Current* IPU OR3Cxx
(
VDD = 5.25 V,
VIN = VSS, TA = 0 °C
)
OR3Txxx
(
VDD = 3.6 V,
VIN = VSS, TA = 0 °C
)
14.4 50.9 14.4 50.9
µ
A
I/O Pad Static
Pull-down Current IPD OR3Cxx
(
VDD = 5.25 V,
VIN = VSS, TA = 0 °C
)
OR3Txxx
(
VDD = 3.6 V,
VIN = VSS, TA = 0 °C
)
26 103 26 103
µ
A
I/O Pad Pull-up
Resistor* RPU VDD = all, VIN = VSS, TA = 0 °C 100 — 100 — kΩ
I/O Pad Pull-down
Resistor RPD VDD = all, VIN = VDD, TA = 0 °C 50 — 50 — kΩ
Lucent Technologies Inc. 103
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics
Description
To define speed grades, the
ORCA
Series pa rt n umb er
designation (see Ordering Information) uses a single-
digit number to designate a speed grade. This number
is not related to any single ac parameter. Higher num-
bers indicate a faster set of timing parameters. The
actual speed sorting is based on testing the delay in a
path consisting of an input buffer, combinatorial delay
through all PLCs in a row, and an output buffer. Other
tests are then done to verify other delay parameters,
such as routing delays, setup times to FFs, etc.
The most accurate timing characteristics are reported
by the timing analyzer in the
ORCA
Foundry Develop-
ment System. A timing report provided by the develop-
ment system after layout divides path delays into logic
and routing delays. The timing analyzer can also pro-
vide logic delays prior to layout. While this allows rout-
ing budget estimates, there is wide variance in routing
delays associated with different layouts.
The logic timing parameters noted in the Electrical
Characteristics section of this data sheet are the same
as those in the design tools . In the PFU timing given in
Table 41—Table 48, symbol names are generally a
concatenation of the PFU operating mode (as defined
in Table 3) and the parameter type. The setup, hold,
and propagation delay parameters, defined below, are
designated in the symbol name by the SET, HLD, and
DEL characters, respectively.
The values given for the parameters are the same as
those used during production testing and speed bin-
ning of the devices. The junction temperature and sup-
ply voltage used to characterize the devices are listed
in the delay tables. Actual delays at nominal tempera-
ture and voltage f or best-case processes can be much
better than the values given.
It should be noted that the junction temper ature used in
the tables is generally 85 °C. The junction temperature
for the FPGA depends on the power dissipated by the
device, the package thermal characteristics (ΘJA), and
the ambient temperature, as calculated in the following
equation and as discussed further in the Package
Thermal Characteristics section:
TJmax = TAmax +
(
P • ΘJA
)
°C
Note: The user must determine this
j
unction tempera-
ture to see if the dela
y
s from
ORCA
Foundr
y
should be derated based on the followin
g
derat-
in
g
tables.
Table 38 and Table 39 provide approximate power sup-
ply and junction temperature derating for OR3Cxx com-
mercial and industrial devices. Table 40 provides the
same information for the OR3Txxx devices (both com-
mercial and industrial). The delay values in this data
sheet and reported by
ORCA
Foundry are shown as
1.00 in the tables. The method for determining the
maximum junction temperature is defined in the Pack-
age Thermal Characteristics section. Taken cumula-
tively, the range of parameter v alues for best-case vs.
worst-ca se proc es si ng, suppl y voltage, and junction
temperature can approach 3 to 1.
Table 38. Dera ti n
g
for Commercial Devices
(
OR3Cxx
)
Table 39. Dera ti n
g
for Industrial Devices
(
OR3Cxx
)
Table 40. Deratin
g
for Commercial/Industrial
Devices
(
OR3Txxx
)
Note: The deratin
g
tables shown above are for a t
y
pical critical path
that contains 33% lo
g
ic dela
y
and 66% routin
g
dela
y
. Since the
routin
g
dela
y
derates at a hi
g
her rate than the lo
g
ic dela
y
, paths
with more than 66% routin
g
dela
y
will derate at a hi
g
her rate
than shown in the table. The approximate deratin
g
values vs.
temperature are 0.26% per °C for lo
g
ic dela
y
and 0.45% per °C
for routin
g
dela
y
. The approximate deratin
g
values vs. volta
g
e
are 0.13% per mV for both lo
g
ic and routin
g
dela
y
s at 25 °C.
TJ
(
°C
)
Power Su
pp
l
y
Volta
g
e
4.75 V 5.0 V 5.25 V
00.81 0.79 0.77
25 0.85 0.83 0.81
85 1.00 0.97 0.95
100 1.05 1.02 1.00
125 1.12 1.09 1.07
TJ
(
°C
)
Power Su
pp
l
y
Volta
g
e
4.5 V 4.75 V 5.0 V 5.25 V 5.5 V
–40 0.71 0.70 0.68 0.66 0.65
00.80 0.78 0.76 0.74 0.73
25 0.84 0.82 0.80 0.78 0.77
85 1.00 0.97 0.94 0.93 0.91
100 1.05 1.01 0.99 0.97 0.95
125 1.12 1.09 1.06 1.04 1.02
TJ
(
°C
)
Power Su
pp
l
y
Volta
g
e
3.0 V 3.3 V 3.6 V
–40 0.73 0.66 0.61
00.82 0.73 0.68
25 0.87 0.78 0.72
85 1.00 0.90 0.83
100 1.04 0.94 0.87
125 1.10 1.00 0.92
104104 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
In addition to supply voltage, process variation, and
operating temperature, circuit and process improve-
ments of the
ORCA
Series FPGAs over time will result
in significant improvement of the actual performance
over those listed for a speed grade. Even though lower
speed grades may still be available, the distribution of
yield to timing parameters may be several speed
grades higher than that designated on a product brand.
Design practices need to consider best-case timing
parameters (e.g., delays = 0), as well as worst-case
timing.
The routing delays are a function of fan-out and the
capacitance associated with the CIPs and metal inter-
connect in the path. The number of logic elements that
can be driven (fan-out) by PFUs is unlimited, although
the delay to reach a valid logic level can exceed timing
requirements. It is difficult to make accurate routing
delay estimates prior to design compilation based on
fan-out. This is because the CAE software may delete
redundant logic inserted by the designer to reduce f an-
out, and/or it may also automatically reduce f an-out by
net splitting.
The waveform test points are giv en in the Input/Output
Buffer Measurement Conditions section of this data
sheet. The timing parameters given in the electrical
characteristics tables in this data sheet follow industry
practices, and the values they reflect are described
below.
Propagation Delay—Th e time between the spe cifi ed
reference points. The delays provided are the worst
case of the tphh and tpll delays for noninverting func-
tions, tplh and tphl for in verting functions, and tphz and
tplz for 3-state enable.
Setup Time—The interval immediately preceding the
transition of a clock or latch enable signal, during which
the data must be stable to ensure it is recognized as
the intended value.
Hold Time—The interval immediately following the
transition of a clock or latch enable signal, during which
the data must be held stable to ensure it is recognized
as the intended value.
3-State Enable—The time from when a 3-state control
signal becomes active and the output pad reaches the
high-im ped anc e sta te.
PFU Timing
* Four-input variab les’ (KZ[3:0]) path delays are valid for LUTs in both F4 (four-input LUT) and F5 (five-input LUT) modes.
Table 41. Combinatorial PFU Timin
g
Characteristics
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Parameter Symbol
Speed
Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Combinatorial Dela
y
s
(
TJ = +85 °C, VDD = min
)
:
Four-input Variables
(
Kz
[
3:0
]
to F
[
z
])
*
Five-input Variables
(
F5
[
A:D
]
to F
[
0, 2, 4, 6
])
Two-level LUT Dela
y
(
Kz
[
3:0
]
to F w/feedbk
)
*
Two-level LUT Dela
y
(
F5
[
A:D
]
to F w/feedbk
)
Thre e-level LUT Dela
y
(
Kz
[
3:0
]
to F w/feedbk
)
*
Thre e-level LUT Dela
y
(
F5
[
A:D
]
to F w/feedbk
)
CIN to COUT De la
y
(
lo
g
ic mode
)
F4_DEL
F5_DEL
SWL2_DEL
SWL2F5_DEL
SWL3_DEL
SWL3F5_DEL
CO_DEL
—
—
—
—
—
—
—
2.34
2.11
4.87
4.69
6.93
6.89
3.47
—
—
—
—
—
—
—
1.80
1.57
3.66
3.51
5.15
5.08
2.65
—
—
—
—
—
—
—
1.32
1.23
2.58
2.48
3.63
3.54
1.79
—
—
—
—
—
—
—
1.05
0.99
2.03
1.94
2.82
2.75
1.43
ns
ns
ns
ns
ns
ns
ns
Lucent Technologies Inc. 105
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Note: See Table 46 for an explanation of FDBK_DEL and OMUX_DEL. 5-5751(F)
Figure 64. Combinatorial PFU Timing
F4_DEL
LUT
F4_DEL/
F5_DEL
LUT
F5–DEL
LUT
F4_DEL/
LUT
F4_DEL/
F5_DEL
LUT
F4_DEL/
F5_DEL
LUT
F4_DEL/
LUT
F4_DEL/
F5_DEL
LUT
F4_DEL/
F5_DEL
LUT
F4_DEL/
F5_DEL
LUT
F4_DEL/
F5_DEL
LUT
F4_DEL/
F5_DEL
LUT
K
Z
[3:0]
K
Z
[3:0], F5[A:D]
K
Z
[3:0]
K
Z
[3:0]
F5[A:D]
F5[A:D]
F[7:0]
F[6, 4,
F[7:0]
F[7:0]
F[7:0]
F[7:0]
FDBK–DEL
O[9:0]
SWL2_DEL
SWL3_DEL
SWL2F5_DEL
SWL3F5_DEL
PFU
8
4
OMUX_DEL
2, 0]
106 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 42. Se
q
uential PFU Timin
g
Characteri stics
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Parameter Symbol
Speed
Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Input Requirements
Clock Low Time CLKL_MPW 3.36 — 2.07 — 0.94 —0.72— ns
Clock Hi
g
h Time CLKH_MPW 1.61 — 1.06 — 0.54 —0.45— ns
Global S/R Pulse Widt h
(
GSRN
)
GSR_MPW 3.36 — 2.07 — 0.94 —0.72— ns
Local S/R Puls e Width LSR_MPW 3.36 — 2.07 — 0.94 —0.72— ns
Combinatorial Setup Times
(
TJ = +85 °C, VDD = min
)
:
Four-input Variables to Clock
(
Kz
[
3:0
]
to CLK
)
*
Five-input Variables to Clock
(
F5
[
A:D
]
to CLK
)
Data In to Clock
(
DIN
[
7:0
]
to CLK
)
Carr
y
-in to Clock, DIRECT to REGCOUT
(
CIN to CLK
)
Clock Enable to Clock
(
CE to CLK
)
Clock Enable to Clock
(
ASWE to CLK
)
Local Set/Reset to Clock
(
SYNC
)
(
LSR to CLK
)
Data Select to Clock
(
SEL to CLK
)
Two-level LUT to Clock
(
Kz
[
3:0
]
to CLK w/feedbk
)
*
Two-level LUT to Clock
(
F5
[
A:D
]
to CLK w/feedbk
)
Three-level LUT to Clock
(
Kz
[
3:0
]
to CLK w/feedbk
)
*
Three-level LUT to Clock
(
F5
[
A:D
]
to CLK w/feedbk
)
F4_SET
F5_SET
DIN_SET
CINDIR_SET
CE1_SET
CE2_SET
LSR_SET
SEL_SET
SWL2_SET
SWL2F5_SET
SWL3_SET
SWL3F5_SET
1.99
1.79
0.47
1.25
2.86
1.68
1.86
1.37
3.98
4.06
6.49
6.39
—
—
—
—
—
—
—
—
—
—
—
—
1.47
1.33
0.32
0.99
2.15
1.30
1.36
1.00
2.99
2.97
4.81
4.73
—
—
—
—
—
—
—
—
—
—
—
—
1.08
1.03
0.18
0.71
1.80
0.95
0.86
0.92
2.13
2.29
3.42
3.34
—
—
—
—
—
—
—
—
—
—
—
—
0.85
0.81
0.16
0.58
1.37
0.77
0.68
0.70
1.63
1.68
2.64
2.57
—
—
—
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Combinatorial Hold Times
(
TJ = all, VDD = all
)
:
Data In
(
DIN
[
7:0
]
from CLK
)
Carr
y
-in from Clock, DIRECT to REGCOUT
(
CIN from
CLK
)
Clock Enable
(
CE from CLK
)
Clock Enable from Clock
(
ASWE from CLK
)
Local Set/Reset from Clock
(
s
y
nc
)
(
LSR from CLK
)
Data Select from Clock
(
SEL from CLK
)
All Others
DIN_HLD
CINDIR_HLD
CE1_HLD
CE2_HLD
LSR_HLD
SEL_HLD
—
0.00
0.00
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
Output Characteristics
Se
q
uential Dela
y
s
(
TJ = +85 °C, VDD = min
)
:
Local S/R
(
as
y
nc
)
to PFU Out
(
LSR to Q
[
7:0
]
, REG-
COUT
)
Global S/R to PFU Out
(
GSRN to Q
[
7:0
]
, REGCOUT
)
Clock to PFU Out—Re
g
ister
(
CLK to Q
[
7:0
]
, REG-
COUT
)
Clock to PFU Out—Latch
(
CLK to Q
[
7:0
])
Transparent Lat c h
(
DIN
[
7:0
]
to Q
[
7:0
])
LSR_DEL
GSR_DEL
REG_DEL
LTCH_DEL
LTCHD_DEL
—
—
—
—
—
7.02
5.21
2.38
2.51
2.73
—
—
—
—
—
5.29
3.90
1.75
1.88
2.10
—
—
—
—
—
3.64
2.55
1.26
1.21
1.38
—
—
—
—
—
2.90
2.00
0.97
0.96
1.12
ns
ns
ns
ns
ns
* Four-input variables’
(
KZ[3:0]
)
setup times are valid for LUTs in both F4
(
four-input LUT
)
and F5
(
five-input LUT
)
modes.
Note: The table shows worst-case dela
y
s.
ORCA
Foundr
y
reports the dela
y
s for individual paths within a
g
roup of paths representin
g
the same
timin
g
parameter and ma
y
accuratel
y
report dela
y
s that are less than those listed.
Lucent Technologies Inc. 107
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 43. Ripple Mode PFU Timing Characteristics
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Parameter
(
TJ = +85 °C, VDD = min
)
Symbol
Speed
Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Full Ripple Setup Times
(
b
y
te wide
)
:
Operands to Clock
(
Kz
[
1:0
]
to CLK
)
Bitwise Operand s to Clock
(
Kz
[
1:0
]
to CLK at F
[
z
])
Fast Carr
y
-in to Clock
(
FCIN to CLK
)
Carr
y
-in to Clock
(
CIN to CLK
)
Add/Subtract to Clock
(
ASWE to CLK
)
Operands to Clock
(
Kz
[
1:0
]
to CLK at REGCOUT
)
Fast Carr
y
-in to Clock
(
FCIN to CLK at REGCOUT
)
Carr
y
-in to Clock
(
CIN to CLK at REGCOUT
)
Add/Subtract to Clock
(
ASWE to CLK at REGCOUT
)
RIP_SET
FRIP_SET
FCIN_SET
CIN_SET
AS_SET
RIPRC_SET
FCINRC_SET
CINRC_SET
ASRC_SET
3.50
1.99
2.55
3.80
8.82
2.09
2.29
3.09
8.14
—
—
—
—
—
—
—
—
—
2.50
1.47
1.87
2.79
6.18
1.61
1.76
2.36
5.73
—
—
—
—
—
—
—
—
—
1.96
1.08
1.34
1.97
4.68
1.19
1.28
1.73
4.54
—
—
—
—
—
—
—
—
—
1.48
0.85
1.04
1.56
3.50
0.93
1.02
1.35
3.39
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
Full Ripple Hold Times
(
TJ = all, VDD = all
)
:
Fast Carr
y
-in from Clock
(
FCIN from CLK at REG-
COUT
)
All Others
FCINRC_HLD
GENERIC_HLD
0.00
0.00
—
—
0.00
0.00
—
—
0.00
0.00
—
—
0.00
0.00
—
—
ns
ns
Half Ripple Setup Times
(
nibble wide
)
:
Operands to Clock
(
Kz
[
1:0
]
to CLK
)
Bitwise Operand s to Clock
(
Kz
[
1:0
]
to CLK at F
[
z
])
Fast Carr
y
-in to Clock
(
FCIN to CLK
)
Carr
y
-in to Clock
(
CIN to CLK
)
Add/Subtract to Clock
(
ASWE to CLK
)
Operands to Clock
(
Kz
[
1:0
]
to CLK at REGCOUT
)
Fast Carr
y
-in to Clock
(
FCIN to CLK at REGCOUT
)
Carr
y
-in to Clock
(
CIN to CLK at REGCOUT
)
Add/Subtract to Clock
(
ASWE to CLK at REGCOUT
)
HRIP_SET
HFRIP_SET
HFCIN_SET
HCIN_SET
HAS_SET
HRIPRC_SET
HFCINRC_SET
HCINRC_SET
HASRC_SET
3.91
1.99
2.55
3.80
8.82
3.03
2.29
3.09
8.14
—
—
—
—
—
—
—
—
—
2.81
1.47
1.87
2.79
6.18
2.31
1.76
2.36
5.73
—
—
—
—
—
—
—
—
—
2.21
1.08
1.34
1.97
4.68
1.68
1.28
1.73
4.54
—
—
—
—
—
—
—
—
—
1.66
0.85
1.04
1.56
3.50
1.32
1.02
1.35
3.39
—
—
—
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
Half Ripple Hold Times
(
TJ = all, VDD = all
)
:
Fast Carr
y
-in from Clock
(
HFCIN from CLK at REG-
COUT
)
All Others
HFCINRC_HLD
GENERIC_HLD
0.00
0.00
—
—
0.00
0.00
—
—
0.00
0.00
—
—
0.00
0.00
—
—
ns
ns
Note: The table shows worst-case dela
y
for the ripple chain.
ORCA
Foundr
y
reports the dela
y
for individual paths within the ripple chain that
will be less than or e
q
ual to those listed above.
108 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timin
g
Characteristics
(
continued
)
Table 43. Ri
pp
le Mode PFU Timin
g
Characteristics (continued)
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Parameter
(
TJ = +85 °C, VDD = min
)
Symbol
Speed
Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Full Ripple Dela
y
s
(
b
y
te wide
)
:
Operands to Carr
y
-out
(
Kz
[
1:0
]
to COUT
)
Operands to Carr
y
-out
(
Kz
[
1:0
]
to FCOUT
)
Operands to PFU Out
(
Kz
[
1:0
]
to F
[
7:0
])
Bitwise Operands to PFU Out
(
Kz
[
1:0
]
to F
[
z
])
Fast Carr
y
-in to Carr
y
-out
(
FCIN to COUT
)
Fast Carr
y
-in to Fast Carr
y
-out
(
FCIN to FCOUT
)
Carr
y
-in to Carr
y
-out
(
CIN to COUT
)
Carr
y
-in to Fast Carr
y
-out
(
CIN to FCOUT
)
Fast Carr
y
-in PFU Out
(
FCIN to F
[
7:0
])
Carr
y
-in PFU Out
(
CIN to F
[
7:0
])
Add/Subtract to Carr
y
-out
(
ASWE to COUT
)
Add/Subtract to Carr
y
-out
(
ASWE to FCOUT
)
Add/Subtract to PFU Out
(
ASWE to F
[
7:0
])
RIPCO_DEL
RIPFCO_DEL
RIP_DEL
FRIP_DEL
FCINCO_DEL
FCINFCO_DEL
CINCO_DEL
CINFCO_DEL
FCIN_DEL
CIN_DEL
ASCO_DEL
ASFCO_DEL
AS_DEL
—
—
—
—
—
—
—
—
—
—
—
—
—
5.32
5.30
7.37
2.34
2.59
2.57
3.47
3.46
6.03
6.91
8.28
8.11
10.66
—
—
—
—
—
—
—
—
—
—
—
—
—
4.11
4.10
5.60
1.80
1.99
1.98
2.65
2.64
4.55
5.21
5.89
5.78
7.55
—
—
—
—
—
—
—
—
—
—
—
—
—
2.98
2.98
4.18
1.32
1.43
1.41
1.79
1.78
3.21
3.53
4.58
4.48
5.85
—
—
—
—
—
—
—
—
—
—
—
—
—
2.32
2.32
3.10
1.05
1.14
1.13
1.43
1.43
2.51
3.05
3.45
3.38
4.38
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Half Ripple De la
y
s
(
nibble wide
)
:
Operands to Carr
y
-out
(
Kz
[
1:0
]
to COUT
)
Operands to Fast Carr
y
-out
(
Kz
[
1:0
]
to FCOUT
)
Operands to PFU Out
(
Kz
[
1:0
]
to F
[
3:0
])
Bitwise Operands to PFU Out
(
Kz
[
1:0
]
to F
[
z
])
Fast Carr
y
-in to Carr
y
-out
(
FCIN to COUT
)
Fast Carr
y
-in to Fast Carr
y
-out
(
FCIN to FCOUT
)
Carr
y
-in to Carr
y
-out
(
CIN to COUT
)
Carr
y
-in to Carr
y
-out
(
CIN to FCOUT
)
Fast Carr
y
-in PFU Out
(
FCIN to F
[
3:0
])
Carr
y
-in PFU Out
(
CIN to F
[
3:0
])
Add/Subtract to Carr
y
-out
(
ASWE to COUT
)
Add/Subtract to Carr
y
-out
(
ASWE to FCOUT
)
Add/Subtract to PFU Out
(
ASWE to F
[
3:0
])
HRIPCO_DEL
HRIPFCO_DEL
HRIP_DEL
HFRIP_DEL
HFCINCO_DEL
HFCINFCO_DEL
HCINCO_DEL
HCINFCO_DEL
HFCIN_DEL
HCIN_DEL
HASCO_DEL
HASFCO_DEL
HAS_DEL
—
—
—
—
—
—
—
—
—
—
—
—
—
5.32
5.30
5.50
2.34
2.59
2.57
3.47
3.46
3.76
4.65
8.28
8.11
9.12
—
—
—
—
—
—
—
—
—
—
—
—
—
4.11
4.10
4.07
1.80
1.99
1.98
2.65
2.64
2.84
3.50
5.89
5.78
6.49
—
—
—
—
—
—
—
—
—
—
—
—
—
2.98
2.98
3.20
1.32
1.43
1.41
1.79
1.78
2.01
2.33
4.58
4.48
4.86
—
—
—
—
—
—
—
—
—
—
—
—
—
2.32
2.32
2.40
1.05
1.14
1.13
1.43
1.43
1.58
2.12
3.45
3.38
3.69
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Note: The table shows worst-case dela
y
for the ripple chain.
ORCA
Foundr
y
reports the dela
y
for individual paths within t he ripple chain that wil l
be less than or e
q
ual to those lis ted above.
Lucent Technologies Inc. 109
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 44. Synchronous Memory Write Characteristics
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
* The RAM is written on the inactive clock ed
g
e followin
g
the active ed
g
e that latches the address, data, and control si
g
nals.
Note: The table shows worst-case dela
y
s.
ORCA
Foundr
y
reports the dela
y
s for individual pat hs within a
g
roup of paths representin
g
the same
timin
g
parameter and ma
y
accuratel
y
report dela
y
s that are less than those listed.
5-4621(F)
Figure 65. S
y
nchronous Memor
y
Write Characteristics
Parameter Symbol Speed Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Write Operati on f or R AM M ode:
Maximum Frequenc
y
Clock Low Time
Clo ck Hi
g
h Time
Clock to Data Valid (CLK to F[6, 4, 2, 0])*
SMCLK_FRQ
SMCLKL_MPW
SMCLKH_MPW
MEM_DEL
—
2.34
3.79
—
151.00
—
—
10.00
—
1.80
2.77
—
197.00
—
—
7.14
—
1.32
2.13
—
254.00
—
—
5.00
—
1.05
1.62
—
315.00
4.08
MHz
ns
ns
ns
Write Operation Setup Ti me:
Address to Clock (CIN to CLK)
Address to Clock (DIN[7, 5, 3, 1] to CLK)
Data to Clock (DIN[6 , 4, 2, 0] to CLK)
Write Enable ( WREN) t o Clock ( A SWE to CLK)
Write-po rt Enable 0 (WP E0) to Clo ck ( C E to
CLK)
Write-po rt Enable 1 (WP E1) to Clo ck ( LSR t o
CLK)
WA4_SET
WA_SET
WD_SET
WE_SET
WPE0_SET
WPE1_SET
1.25
0.72
0.02
0.18
2.25
2.79
—
—
—
—
—
—
0.99
0.52
0.06
0.16
1.69
2.13
—
—
—
—
—
—
0.71
0.35
0.00
0.14
1.16
1.58
—
—
—
—
—
—
0.58
0.28
0.00
0.12
0.84
1.31
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
Write Operation Hold Time:
Address from Clo ck ( C IN from CLK)
Address from Clo ck ( D IN [7 , 5, 3, 1] from C LK)
Data from Clock (DIN[6, 4, 2, 0] from CLK)
Write Enable (WREN) from Clock (ASWE from
CLK)
Write-po rt Enable 0 (WP E 0) from Clock (C E
from CL K)
Write-po rt Enable 1 (WP E 1) from Clock (LSR
from CL K)
WA4_HLD
WA_HLD
WD_HLD
WE_HLD
WPE0_HLD
WPE1_HLD
0.00
0.00
0.59
0.03
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.42
0.00
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.40
0.08
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.32
0.06
0.00
0.00
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
CK
F[6, 4, 2, 0]
CIN, DIN[7 , 5 , 3, 1]
DIN[6, 4, 2, 0]
MEM_DEL
WA4_SET
ASWE (WREN)
CE (WPE0) ,
T
SCH
T
SCL
WA4_HLD
WD_SET WD_HLD
WE_SET WE_HLD
WPE0_SET WPE0_HLD
WA_SET WA_HLD
WPE1_SET WPE1_HLD
LSR (WPE1)
110 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 45. S
y
nchronous Memor
y
Read Characteristics
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Note: The table shows worst-case dela
y
s.
ORCA
Foundr
y
reports the dela
y
s for individual paths within a
g
roup of paths representin
g
the same
timin
g
parameter and ma
y
accuratel
y
report dela
y
s that are less than those listed.
5-4622(F)
Figure 66. Synchronous Memory Read Cycle
Parameter
(
TJ = 85 °C, VDD = min
)
Symbol Speed Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Read Operation:
Data Valid After Address
(
Kz
[
3:0
]
to F
[
6, 4, 2, 0
])
Data Valid After Address
(
F5
[
A:D
]
to F
[
6, 4, 2, 0
])
RA_DEL
RA4_DEL —
—2.34
2.11 —
—1.80
1.57 —
—1.32
1.23 —
—1.05
0.99 ns
ns
Read Operation, Clockin
g
Data into Latch/FF:
Address to Clock Setup Time
(
Kz
[
3:0
]
to CLK
)
Address to Clock Setup Time
(
F5
[
A:D
]
to CLK
)
Address from Clock Hold Time
(
Kz
[
3:0
]
from CLK
)
Address from Clock Hold Time
(
F5
[
A:D
]
from CLK
)
Clock to PFU Output—Re
g
ister
(
CLK to Q
[
6, 4, 2, 0
])
Read C
y
cle Dela
y
RA_SET
RA4_SET
RA_HLD
RA4_HLD
REG_DEL
SMRD_CYC
1.99
1.79
0.00
0.00
—
—
—
—
—
—
2.38
10.48
1.47
1.33
0.00
0.00
—
—
—
—
—
—
1.75
7.66
1.08
1.03
0.00
0.00
—
—
—
—
—
—
1.26
7.53
0.85
0.81
0.00
0.00
—
—
—
—
—
—
0.97
5.78
ns
ns
ns
ns
ns
ns
Kz[3:0], F5[A:D]
F[6, 4, 2, 0]
CLK
Q[3:0]
RA_DEL
RA4_DEL
RA_SET
RA4_SET
REG_DEL
RA_HLD
RA4_HLD
SMRD_CYC
Lucent Technologies Inc. 111
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
PLC Timing
Table 46. PFU Ou t
p
ut MUX and Direct Routin
g
Timin
g
Characteristics
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
* This is
g
eneral feedback usin
g
switchin
g
se
g
ments. See the combinatorial PFU timin
g
table for softwired look-up table feedback timin
g
.
SLIC Timing
Table 47. Su
pp
lemental Lo
g
ic and Interconnect Cell
(
SLIC
)
Timin
g
Characteri stics
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Parameter
(
TJ = 85 °C, VDD = min
)
Symbol
Speed
Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
PFU Output MUX
(
Fan-out = 1
)
Output MUX Dela
y
(
F
[
7:0
]
/Q
[
7:0
]
to O
[
9:0
])
Carr
y
-out MUX Dela
y
(
COUT to O9
)
Re
g
istered Carr
y
-out MUX Dela
y
(
REGCOUT
to O8
)
OMUX_DEL
COO9_DEL
RCOO8_DEL
—
—
—
0.50
0.34
0.34
—
—
—
0.39
0.26
0.26
—
—
—
0.35
0.24
0.24
—
—
—
0.28
0.18
0.18
ns
ns
ns
Direct Routing
PFU Feedba ck
(
xSW
)
*
PFU to Ortho
g
onal PFU Dela
y
(
xSW to xSW
)
PFU to Dia
g
onal PFU Dela
y
(
xBID to xSW
)
FDBK_DEL
ODIR_DEL
DDIR_DEL
—
—
—
1.74
2.21
2.69
—
—
—
1.41
1.77
2.19
—
—
—
1.48
1.75
2.53
—
—
—
1.14
1.39
1.98
ns
ns
ns
Parameter
(
TJ = 85 °C, VDD = min
)
Symbol
Speed Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
3-Statable BIDIs
BIDI Dela
y
(
BRx to BLx, BLx to BRx
)
BIDI Dela
y
(
Ox to BRx, Ox to BLx
)
BIDI 3-state Enable/Disable Dela
y
(
TRI to BL, BR
)
BIDI 3-state Enable/Disable Dela
y
(
BL, BR via DEC, TRI to BL, BR
)
BUF_DEL
OBUF_DEL
TRI_DEL
DECTRI_DEL
—
—
—
—
0.84
0.72
2.55
3.59
—
—
—
—
0.70
0.61
1.90
2.65
—
—
—
—
0.94
0.87
1.31
1.91
—
—
—
—
0.77
0.70
1.01
1.48
ns
ns
ns
ns
Decoder
Decoder Dela
y
(
BR
[
9:8
]
, BL
[
9:8
]
to DEC
)
Decoder Dela
y
(
BR
[
7:0
]
, BL
[
7:0
]
to DEC
)
DEC98_DEL
DEC_DEL —
—2.39
2.35 —
—1.85
1.82 —
—1.27
1.23 —
—1.02
0.99 ns
ns
112 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
PIO Timing
Table 48. Pro
g
rammable I/O
(
PIO
)
Timin
g
Characteristics
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Parameter Symbol Speed Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Input Delays
(
TJ = 85 °C, VDD = min
)
Input Rise Time IN_RIS — 500 — 500 — 500 — 500 ns
Input Fall Time IN_FAL — 500 — 500 — 500 — 500 ns
PIO Direct Delays:
Pad to In (pad to CLK IN)
Pad to In (pad to IN1, IN2)
Pad to In Delayed (pad to IN1, IN2)
CKIN_DEL
IN_DEL
IND_DEL
—
—
—
1.41
2.16
9.05
—
—
—
1.26
1.87
7.83
—
—
—
0.64
1.28
6.64
—
—
—
0.41
0.90
7.27
ns
ns
ns
PIO Transparent Latch Delays:
Pad to In (pad to IN1, IN2)
Pad to In Delayed (pad to IN1, IN2) LATCH_DEL
LATCHD_DEL —
—4.11
10.58 —
—3.25
9.05 —
—2.52
7.67 —
—1.82
7.65 ns
ns
Input Latch/FF Setup Timing:
Pad to ExpressCLK (fast-capture latch/FF)
Pad Delayed to ExpressCLK
(fast-capture latch/FF)
Pad to Clock (input latch/FF)
Pad Delayed to Clock (input latch/FF)
Clock Enable to Clock (CE to CLK)
Local Set/Reset (sync) to Clock (LSR to CLK)
INREGE_SET
INREGED_SET
INREG_SET
INREGD_SET
INCE_SET
INLSR_SET
5.93
12.86
1.62
8.57
2.03
1.79
—
—
—
—
—
—
4.82
11.03
1.42
7.36
1.64
1.45
—
—
—
—
—
—
3.63
9.18
0.71
5.91
1.29
1.14
—
—
—
—
—
—
3.23
9.68
0.50
7.06
1.00
0.89
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
Input FF/Latch Hold Timing:
Pad from ExpressCLK (fast-capture latch/FF)
Pad Delayed from ExpressCLK
(fast-capture latch/FF)
Pad from Clock (input latch/FF)
Pad Delayed from Clock (input latch/FF)
Clock Enable from Clock (CE from CLK)
Local Set/Reset (sync) from Clock
(LSR from CLK)
INREGE_HLD
INREGED_HLD
INREG_HLD
INREGD_HLD
INCE_HLD
INLSR_HLD
0.00
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
—
ns
ns
ns
ns
ns
ns
Clock-to-in Delay (FF CLK to IN1, IN2)
Clock-to-in Delay (latch CLK to IN1, IN2)
Local S/R (async) to IN (LSR to IN1, IN2)
Local S/R (async) to IN (LSR to IN1, IN2)
LatchFF in Latch Mode
Global S/R to In (GSRN to IN1, IN2)
INREG_DEL
INLTCH_DEL
INLSR_DEL
INLSRL_DEL
INGSR_DEL
—
—
—
—
—
4.05
4.08
6.11
5.89
5.38
—
—
—
—
—
3.14
3.19
4.76
4.66
4.22
—
—
—
—
—
2.53
2.62
3.81
3.57
3.44
—
—
—
—
—
2.05
2.14
3.17
2.98
2.88
ns
ns
ns
ns
ns
Note: The dela
y
s for all input buffers assume an input rise/fall time of <1 V/ns.
Lucent Technologies Inc. 113
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 48. Pro
g
rammable I/O
(
PIO
)
Timi n
g
Characteri stics (continued)
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Parameter Symbol Speed Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Output Delays
(
TJ = 85 °C, VDD = min, CL = 50 pF
)
Output to Pad
(
OUT2, OUT1 direct to pad
)
:
Fast
Slewlim
Sinklim
OUTF_DEL
OUTSL_DEL
OUTSI_DEL
—
—
—
5.09
7.86
9.41
—
—
—
4.21
6.49
7.98
—
—
—
2.63
3.49
8.08
—
—
—
2.17
2.91
7.32
ns
ns
ns
3-state E nable/Disable De la
y
(
TS to pad
)
:
Fast
Slewlim
Sinklim
TSF_DEL
TSSL_DEL
TSSI_DEL
—
—
—
4.93
7.70
9.25
—
—
—
4.09
6.37
7.86
—
—
—
2.33
3.00
7.95
—
—
—
1.88
2.41
7.23
ns
ns
ns
Local Set/Reset
(
as
y
nc
)
to Pad
(
LSR to pad
)
:
Fast
Slewlim
Sinklim
OUTLSRF_DEL
OUTLSRSL_DEL
OUTLSRSI_DEL
—
—
—
9.03
11.79
13.35
—
—
—
7.25
9.53
11.02
—
—
—
4.96
5.82
10.38
—
—
—
3.94
4.67
9.10
ns
ns
ns
Global Set/Reset to Pad
(
GSRN to pad
)
:
Fast
Slewlim
Sinklim
OUTGSRF_DEL
OUTGSRSL_DEL
OUTGSRSI_DEL
—
—
—
8.30
11.06
12.62
—
—
—
6.69
8.97
10.46
—
—
—
4.39
5.07
10.02
—
—
—
3.46
3.99
8.81
ns
ns
ns
Output FF Setup Timin
g
:
Out to ExpressCLK
(
OUT
[
2:1
]
to ECLK
)
Out to Clock
(
OUT
[
2:1
]
to CLK
)
Clock Enable to Clock
(
CE to CLK
)
Local Set/Reset
(
s
y
nc
)
to Clock
(
LSR to CLK
)
OUTE_SET
OUT_SET
OUTCE_SET
OUTLSR_SET
0.00
0.00
0.91
0.41
—
—
—
—
0.00
0.00
0.67
0.32
—
—
—
—
0.00
0.00
0.56
0.26
—
—
—
—
0.00
0.00
0.45
0.24
—
—
—
—
ns
ns
ns
ns
Output FF Hold Timin
g
:
Out from ExpressCLK
(
OUT
[
2:1
]
from ECLK
)
Out from Clock
(
OUT
[
2:1
]
from CLK
)
Clock Enable fr om Clock
(
CE from CLK
)
Local Set/Reset
(
s
y
nc
)
from Clock
(
LSR from
CLK
)
OUTE_HLD
OUT_HLD
OUTCE_HLD
OUTLSR_HLD
0.73
0.73
0.00
0.00
—
—
—
—
0.58
0.58
0.00
0.00
—
—
—
—
0.36
0.36
0.00
0.00
—
—
—
—
0.29
0.29
0.00
0.00
—
—
—
—
ns
ns
ns
ns
Clock to Pad Dela
y
(
ECLK, SCLK to pad
)
:
Fast
Slewlim
Sinklim
OUTREGF_DEL
OUTREGSL_DEL
OUTREGSI_DEL
—
—
—
6.71
9.47
11.03
—
—
—
5.44
7.71
9.20
—
—
—
3.56
4.42
8.98
—
—
—
2.78
3.52
7.94
ns
ns
ns
Addit ion al Dela
y
If Usin
g
Open Drain OD_DEL — 0.20 — 0.16 — 0.10 — 0.08 ns
Note: The dela
y
s for all input buffers assume an input rise/fall time of <1 V/ns.
114 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 48. Pro
g
rammable I/O
(
PIO
)
Timin
g
Characteristics (continued)
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Parameter Symbol Speed Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
PIO Logic Block Delays
Out to Pad
(
OUT
[
2:1
]
via lo
g
ic to pad
)
:
Fast
Slewlim
Sinklim
OUTLF_DEL
OUTLSL_DEL
OUTLSI_DEL
—
—
—
5.09
7.86
9.41
—
—
—
4.21
6.49
7.98
—
—
—
2.63
3.49
8.08
—
—
—
2.17
2.91
7.32
ns
ns
ns
Outre
g
to Pad
(
OUTREG via lo
g
ic to pad
)
:
Fast
Slewlim
Sinklim
OUTRF_DEL
OUTRSL_DEL
OUTRSI_DEL
—
—
—
6.71
9.47
11.03
—
—
—
5.44
7.71
9.20
—
—
—
3.56
4.42
8.98
—
—
—
2.78
3.52
7.94
ns
ns
ns
Clock to Pad
(
ECLK, CLK via lo
g
ic to pad
)
:
Fast
Slewlim
Sinklim
OUTCF_DEL
OUTCSL_DEL
OUTCSI_DEL
—
—
—
6.97
9.74
11.29
—
—
—
5.68
7.96
9.45
—
—
—
3.71
4.57
9.13
—
—
—
2.91
3.64
8.07
ns
ns
ns
3-State FF Delays
3-state Enable/Disable Dela
y
(
TS direct to
pad
)
:
Fast
Slewlim
Sinklim
TSF_DEL
TSSL_DEL
TSSI_DEL
—
—
—
4.93
7.70
9.25
—
—
—
4.09
6.37
7.86
—
—
—
2.33
3.00
7.95
—
—
—
1.88
2.41
7.23
ns
ns
ns
Local Set/Res et
(
as
y
nc
)
to Pad
(
LSR to
pad
)
:
Fast
Slewlim
Sinklim
TSLSRF_DEL
TSLSRSL_DEL
TSLSRSI_DEL
—
—
—
8.25
11.01
12.57
—
—
—
6.65
8.92
10.41
—
—
—
4.24
4.92
9.87
—
—
—
3.39
3.92
8.74
ns
ns
ns
Global Set/Reset to Pad
(
GSRN to pad
)
:
Fast
Slewlim
Sinklim
TSGSRF_DEL
TSGSRSL_DEL
TSGSRSI_DEL
—
—
—
7.52
10.28
11.84
—
—
—
6.09
8.36
9.85
—
—
—
3.88
4.55
9.51
—
—
—
3.11
3.64
8.45
ns
ns
ns
3-State FF Setup Timin
g
:
TS to ExpressCLK
(
TS to ECLK
)
TS to Clock
(
TS to CLK
)
Local Set/Reset
(
s
y
nc
)
to Clock
(
LSR to
CLK
)
TSE_SET
TS_SET
TSLSR_SET
0.00
0.00
0.28
—
—
—
0.00
0.00
0.21
—
—
—
0.00
0.00
0.17
—
—
—
0.00
0.00
0.18
—
—
—
ns
ns
ns
3-State FF Hold Timin
g
:
TS from ExpressCLK
(
TS from ECLK
)
TS from Clock
(
TS from CLK
)
Local Set/Reset
(
s
y
nc
)
from Clock
(
LSR from CLK
)
TSE_HLD
TS_HLD
TSLSR_HLD
0.85
0.85
0.00
—
—
—
0.68
0.68
0.00
—
—
—
0.44
0.44
0.00
—
—
—
0.34
0.34
0.00
—
—
—
ns
ns
ns
Clock to Pad Dela
y
(
ECLK, SCLK to pad
)
:
Fast
Slewlim
Sinklim
TSREGF_DEL
TSREGSL_DEL
TSREGSI_DEL
—
—
—
5.94
8.70
10.26
—
—
—
4.82
7.10
8.59
—
—
—
2.84
3.52
8.47
—
—
—
2.23
2.76
7.58
ns
ns
ns
Note: The dela
y
s for all input buffers assume an input rise/fall time of <1 V/ns.
Lucent Technologies Inc. 115
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Special Function Blocks Timing
Table 49. Microprocessor Interface (MPI) Timing Characteristics
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
1. For user s
y
stem flexibilit
y
, CS0 and CS1 ma
y
be set up to an
y
one of the three ri sin
g
clock ed
g
es, be
g
innin
g
with the risin
g
clock ed
g
e when
MPI_STRB is low. If both chip selects are valid and the setup time is met, the MPI will latch the chip select state, and CS0 and CS1 ma
y
g
o
inactive before the end of the read/write c
y
cle.
2. 0.5 MPI_CLK.
3. Write data and W/R have to be valid startin
g
from the clock c
y
cle after both ADS and CS0 and CS1 are reco
g
nized.
4. Write data and W/R have to be held until the microprocessor receives a valid RDYRCV.
Notes:
Read and write descriptions are referenced to the host microprocessor; e.
g
., a read is a read b
y
the host
(
PowerPC
,
i960
)
from the FPGA.
PowerPC
and
i960
timin
g
s to/from the clock are relative to the clock at the FPGA microprocessor interface clock pin
(
MPI_CLK
)
.
Parameter Symbol
Speed
Unit–4 –5 –6 –7
MinMaxMinMaxMinMaxMinMax
PowerPC
Interface Timing
(
TJ = 85 °C, VDD = min
)
Transfer Acknowled
g
e Dela
y
(
CLK to TA
)
Burst Inhibit Dela
y
(
CLK to BIN
)
Transfer Acknowled
g
e Dela
y
to Hi
g
h Impedance
Burst Inhibit Dela
y
to Hi
g
h Impedance
Write Data Setup Time
(
data to TS
)
Write Data Hold Time
(
data from CLK while MPI_ACK low
)
Address Setup Time
(
addr to TS
)
Address Hold Time
(
addr from CLK while MPI_ACK low
)
Read/Write Setup Time
(
R/W to TS
)
Read/Write Hold Time
(
R/W from CLK while MPI_ACK low
)
Chip Select Setup Time
(
CS0, CS1 to TS
)
Chip Select Hold Time
(
CS0, CS1 from CLK
)
User Address Dela
y
(
pad to UA
[
3:0
])
User Read/W ri te D ela
y
(
pad to URDWR_DEL
)
TA_DEL
BI_DEL
TA_DELZ
BI_DELZ
WD_SET
WD_HLD
A_SET
A_HLD
RW_SET
RW_HLD
CS_SET
CS_HLD
UA_DEL
URDWR_DEL
—
—
—
—
0.0
0.0
0.0
0.0
0.0
0.0
0.3
0.0
—
—
11.6
11.6
(
2
)
(
2
)
—
—
—
—
—
—
—
—
3.3
7.0
—
—
—
—
0.0
0.0
0.0
0.0
0.0
0.0
.25
0.0
—
—
9.3
9.3
(
2
)
(
2
)
—
—
—
—
—
—
—
—
2.6
5.4
—
—
—
—
0.0
0.0
0.0
0.0
0.0
0.0
.14
0.0
—
—
8.0
8.0
(
2
)
(
2
)
—
—
—
—
—
—
—
—
2.3
4.2
—
—
—
—
0.0
0.0
0.0
0.0
0.0
0.0
.12
0.0
—
—
6.8
6.8
(
2
)
(
2
)
—
—
—
—
—
—
—
—
1.9
3.6
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
i960
Interface Timing
(
TJ = 85 °C, VDD = min
)
Addr/Data Select to ALE
(
ADS, to ALE low
)
Addr/Data Select to ALE
(
ADS, from ALE low
)
Read
y
/Receive Dela
y
(
CLK to RDYRCV
)
Read
y
/Receive Dela
y
to Hi
g
h Impedanc e
Write Data Setup Time
Write Data Hold Time
Address Setup Time
(
addr to ALE low
)
Address Hold Time
(
addr from ALE low
)
B
y
te Enable Setup Time
(
BE0, BE1 to ALE low
)
B
y
te Enable Hold Time
(
BE0, BE1 from ALE low
)
Read/Write Setup Time
Read/Write Hold Time
Chip Select Setup Time
(
CS0, CS1 to CLK
)
(
1
)
Chip Select Hold Time
(
CS0, CS1 from CLK
)
(
1
)
User Address Dela
y
(
CLK low to UA
[
3:0
])
User Read/W ri te D ela
y
(
pad to URDWR_DEL
)
ADSN_SET
ADSN_HLD
RDYRCV_DEL
RDYRCV_DELZ
WD_SET
WD_HLD
A_SET
A_HLD
BE_SET
BE_HLD
RW_SET
RW_HLD
CS_SET
CS_HLD
UA_DEL
URDWR_DEL
2.0
0.0
—
—
(
3
)
(
4
)
2.0
2.0
2.0
2.0
(
3
)
(
4
)
2.0
0.0
—
—
—
—
11.6
(
2
)
—
—
—
—
—
—
—
—
—
—
6.6
7.0
1.8
0.0
—
—
(
3
)
(
4
)
1.8
1.8
1.8
1.8
(
3
)
(
4
)
1.8
0.0
—
—
—
—
9.3
(
2
)
—
—
—
—
—
—
—
—
—
—
4.3
5.4
1.6
0.0
—
—
(
3
)
(
4
)
0.50
0.51
0.50
0.51
(
3
)
(
4
)
0.45
0.0
—
—
—
—
8.0
(
2
)
—
—
—
—
—
—
—
—
—
—
4.1
4.2
1.4
0.0
—
—
(
3
)
(
4
)
—
—
—
—
(
3
)
(
4
)
—
0.0
—
—
—
—
6.8
(
2
)
—
—
0.42
0.44
0.42
0.44
—
—
0.38
—
3.5
3.6
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
116 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timin
g
Characteristics
(
continued
)
Table 49. Microprocessor Interface (MPI) Timing Characteristics (con tinued )
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
1. For user s
y
stem flexibilit
y
, CS0 and CS1 ma
y
be set up to an
y
one of the three risin
g
clock ed
g
es, be
g
innin
g
with the risin
g
clock ed
g
e when
MPI_STRB is low. If both chip selects are valid and the setup time is met, the MPI will latch the chip select state, and CS0 and CS1 ma
y
g
o
inactive before the end of the read/write c
y
cle.
2. 0.5 MPI_C LK.
3. Write data and W/R have to be valid startin
g
from the clock c
y
cle after both ADS and CS0 and CS1 are reco
g
nized.
4. Write data and W/R have to be held until the microprocessor receives a valid RDYRCV.
5. User Lo
g
ic Dela
y
has no predefined value. The user must
g
enerate a UEND si
g
nal to complete the c
y
cle.
6. USTART_DEL is based on the fallin
g
clock ed
g
e.
7. There is no specific time associated with this delay. The user must assert UEND low to complete this cycle.
8. The user must assert interrupt request low until a service routine is executed.
9. This should be at least one MPI_CLK c
y
cle.
10. User should set up read data so that RDS_SET and RDS_HLD can be met for the micro process or timing.
Notes:
Read and write descriptions are referenced to the host microprocessor; e.
g
., a read is a read b
y
the host
(
PowerPC
,
i960
)
from the FPGA.
PowerPC
and
i960
timin
g
s to/from the clock are relative to the clock at the FPGA microprocessor interface clock pin
(
MPI_CLK
)
.
Parameter Symbol
Speed
Unit–4 –5 –6 –7
Min Max Min Max Min Max Min Max
User Lo
g
ic Dela
y
(
5
)
User Lo
g
ic Dela
y
————————ns
User Start Dela
y
(
MP I_CLK fal l in
g
to USTART
)
(
6
)
USTART_DEL — 3.6 — 3.4 — 3.3 — 2.8 ns
User Start Clear Dela
y
(
MPI_CLK to USTART
)
USTARTCLR_DEL — 7.5 — 7.3 — 7.1 — 6.0 ns
User End Delay (USTART low to UEND low)
(
7
)
UEND_DEL — — — — — — — — ns
S
y
nchronous User Timin
g
:
User End Setup
(
UEND to MPI_CLK
)
UEND_SET 0.00 — 0.00 — 0.00 — 0.00 — ns
User End Hold
(
UEND to MPI_CLK
)
UEND_HLD 1.0 — 0.95 — 0.88 — 0.75 — ns
Data Setup for Read
(
D
[
7:0
]
to MPI_CLK
)
(
9
)
RDS_SET ————————ns
Data Hold for Read
(
D
[
7:0
]
from MPI_CLK
)
(
9
)
RDS_HLD ————————ns
As
y
nchronou s Us er Timin
g
:
User End to Read Data Dela
y
(
UEND to
D
[
7:0
]
)
(
10
)
RDA_DEL ————————ns
Data Hold from User Start
(
low
)
(
9
)
RDA_HLD ————————ns
Interrupt R e
q
uest Pulse Width
(
8
)
TUIRQ_PW ————————ns
Lucent Technologies Inc. 117
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
5-5832(F)
Figure 67. MPI
PowerPC
User Space Read Timing
5-5840(F)
Figure 68. MPI
PowerPC
User Space Write Timing
MPI_CLK
A[4:0]
MPI_RW (RD/WR)
CS0, CS1
D[7:0]
MPI_STRB (TS)
UA[3:0]
URDWRN
USTART
UEND
MPI_ACK (TA)
MPI_BI (BI)
A_SET
RW_SET
CS_SET
URDWR_DEL
RDS_SET
A_HLD
CS_HLD
RDS_HLD
RDA_DEL RDA_HLD
USTART_DEL
USER LOGIC DELAY
TA_DEL
BI_DEL BI_DEL
TA_DEL
UEND_DEL
USTARTCLR_DEL
RW_HLD
UA_DEL
UEND_SET
TA_DELZ
BI_DELZ
MPI_CLK
A[4:0]
MPI_RW (RD/WR)
CS0, CS1
D[7:0]
MPI_STRB (TS)
UA[3:0]
URDWRN
USTART
UEND
MPI_ACK (TA)
MPI_BI (BI)
A_SET
RW_SET
CS_SET
URDWR_DEL
UEND_SET
A_HLD
RW_HLD
CS_HLD
WD_HLD
USTART_DEL
USER LOGIC DELAY
TA_DEL
BI_DEL BI_DEL
TA_DEL
UEND_DEL
USTARTCLR_DEL
UA_DEL
BI_DELZ
TA_DELZ
WD_SET
118 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
5-5832(F).c
Figure 69. MPI
PowerPC
Internal Read Timin
g
5-5840(F).e
Figure 70. MPI
PowerPC
Internal Write Timin
g
MPI_CLK
A[4:0]
MPI_R W (RD/WR)
CS0, CS1
D[7:0]
MPI_STRB (TS)
UA[3:0]
URDWRN
MPI_ACK (TA)
MPI_BI (BI)
A_SET
RW_SET
CS_SET
URDWR_DEL
RDS_SET
A_HLD
CS_HLD
RDS_HLD
RDA_DEL RDA_HLD
TA_DEL
BI_DEL BI_DEL
TA_DEL
RW_HLD
UA_DEL
UEND_SET
TA_DELZ
BI_DELZ
MPI_CLK
A[4:0]
MPI_R W (RD/WR)
CS0, CS1
D[7:0]
MPI_STRB (TS)
UA[3:0]
URDWRN
MPI_ACK (TA)
MPI_BI (BI)
A_SET
RW_SET
CS_SET
URDWR_DEL
A_HLD
RW_HLD
CS_HLD
WD_HLD
TA_DEL
BI_DEL BI_DEL
TA_DEL
UA_DEL
BI_DELZ
TA_DELZ
WD_SET
Lucent Technologies Inc. 119
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
5-5831(F).b
Figure 71. MPI
i960
User S
p
ace Read Timing
5-5830(F).b
Figure 72. MPI
i960
User S
p
ace Write Timin
g
MPI_CLK
D[7:0]
MP I_RW (W/R)
CS0, CS 1
MPI_AL E (AL E)
MPI_STRB (ADS)
UA[3:0]
URDWRN
USTART
UEND
MPI_ACK (RDYRCV)
ADSN_HLD
A_SET
ADDR DATA
UA_DEL
UEND_SET
RDYRCV_DEL
USTART_DEL
USER LOG IC D ELAY
RDYRCV_DEL
UEND_DEL
USTARTCLR_DEL
CS_HLD
RDS_HLD
RW_HLDRDS_SET
RDA_DEL RDA_HLD
BE0, BE1
BE_HLD
BE_SET
RDYRCV_DELZ
URDWR_DEL
ADSN_SET
RW_SET
A_HLDCS_SET
MPI_CLK
D[7:0]
MPI_RW (W/R)
CS0, CS1
MPI_ALE (ALE)
MPI_STRB (ADS)
UA[3:0]
URDWRN
USTART
UEND
MPI_ACK (RDYRCV)
A_HLD
ADSN_HLD
A_SET
DATA
URDWR_DEL
UEND_SET
RDYRCV_DEL
USTART_DEL
USER LOGIC DELAY
RDYRCV_DEL
UEND_DEL
USTARTCLR_DEL
CS_HLD
WD_HLD
RW_HLD
WD_SET
UA_DEL
RDYRCV_DELZ
ADDR
CS_SET
RW_SET
ADSN_SET
120 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
5-5831(F).c
Figure 73. MPI
i960
Internal Read Timing
5-5830(F).c
Figure 74. MPI
i960
Internal Write Timin
g
MPI_CLK
D[7:0]
MPI_RW (W /R)
CS0, CS1
MPI_ALE (ALE)
MPI_STRB (A D S)
UA[3:0]
URDWRN
MPI_ACK (RDYRCV)
ADSN_HLD
A_SET
ADDR DATA
UA_DEL
RDYRCV_DEL
RDYRCV_DEL
CS_HLD
RDS_HLD
RW_HLDRDS_SET
RDA_DEL RDA_HLD
BE0, BE1
BE_HLD
BE_SET
RDYRCV_DELZ
URDWR_DEL
ADSN_SET
RW_SET
A_HLDCS_SET
MPI_CLK
D[7:0]
MPI_RW ( W/R)
CS0, CS1
MPI_ALE (ALE)
MPI_STRB (ADS)
UA[3:0]
URDWRN
MPI_ACK (RDY RCV)
A_HLD
ADSN_HLD
A_SET
DATA
URDWR_DEL
RDYRCV_DEL
RDYRCV_DEL
CS_HLD
WD_HLD
RW_HLD
WD_SET
UA_DEL
RDYRCV_DELZ
ADDR
CS_SET
RW_SET
ADSN_SET
Lucent Technologies Inc. 121
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 50. Programmable Clock Manager (PCM) Timing Characteristics (Preliminary Information)
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C ≤TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
* Input frequency tolerance is the allowed input clock frequency change in parts per million.
† See Table 29 and Table 30 for acquisition times for individual frequencies.
‡ PLL mode, divider reg = 1111111 (input freq. = output freq.).
Note: All timing values for the PCM are preliminary information.
Parameter Symbol
Speed
Unit-4 -5 -6 -7
MinMaxMinMaxMinMaxMinMax
Input Clock Frequency: FPCMI
OR3Cxx 51335133————MHz
OR3Txxx — — 5 133 5 133 5 133 MHz
Output Clock Frequency: FPCMO
OR3Cxx 51355135————MHz
OR3Txxx — — 5 100 5 100 5 100 MHz
Input Clock Duty Cycle PCMI_DUTY 30.00 70.00 30.00 70.00 30.00 70.00 30.00 70.00 %
Output Clock Duty Cycle PCMO_DUTY 3.13 96.90 3.13 96.90 3.13 96.90 3.13 96.90 %
Input Frequency Toleranc e* FTOL — 26400 — 26400 — 26400 — 26400 ppm
PCM Acquisition Time (CLK In to
LOCK) PCM_ACQ†36 100 36 100 36 100 36 100
µ
s
PCM Off Delay (config. Done-L, WE to
PCM power off) PCMOFF_DEL — 100.0 — 100.0 — 100.0 — 100.0 ns
PCM Delay in DLL Mode (propagation
delay) PCMDLL-DEL — 1.95 — 1.82 — 1.63 — 1.50 ns
PCM Delay in PLL Mode (propagation
delay) PCMPLL_DEL — 0.00 — 0.00 — 0.00 — 0.00 ns
PCM Clock In to PCM Clock Out
(CLK In to ECLK)‡PCMBYE_DEL — 0.47 — 0.36 — 0.26 — 0.24 ns
PCM Clock In to PCM Clock Out
(CLK In to SCLK)‡PCMBYS_DEL — 0.47 — 0.36 — 0.26 — 0.24 ns
Routed Clock-in Delay (routing to PCM
phase detect, using DIV0) RTCKD_DEL — 1.30 — 1.10 — 0.90 — TBD ns
System Cloc k-out Dela y (PCM osci lla-
tor to SCLK output at PCM) PCMSCK_DEL — 2.70 — 2.20 — 1.90 — TBD ns
Parameter Symbol fOUT (MHz) PLL Mode DLL Mode Unit
Output Ji tter OUTJIT 5—20 250 200 ps
21—30 210 170 ps
31—40 180 145 ps
41—50 155 123 ps
51—60 130 105 ps
61—70 110 90 ps
71—80 95 75 ps
81—90 80 65 ps
91—100 70 55 ps
122 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (con tinued)
Table 51. Boundary-Scan Timing Characteristics
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
5-6764(F)
Figure 75. Boundary-Scan Timing Diagram
Parameter S
y
mbol Min Max Unit
TDI/TMS to TCK Setup Time TS25.0 — ns
TDI/TMS Hold Time from TCK TH0.0 — ns
TCK Low Time TCL 50.0 — ns
TCK Hi
g
h Time TCH 50.0 — ns
TCK to TDO Dela
y
TD— 20.0 ns
TCK Fre
q
uenc
y
TTCK — 10.0 MHz
TCK
TMS
TDI
TDO
TSTH
TD
Lucent Technologies Inc. 123
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Clock Timing
Table 52. ExpressCLK
(
ECLK
)
and Fast Clock
(
FCLK
)
Timin
g
Characteristics
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Notes:
The ECLK dela
y
s are to all of the PICs on one side of the device for middle pin input, or two sides of the device for corner pin input. The dela
y
includes both the input buffer dela
y
and the clock routin
g
to the PIC clock input.
The FCLK dela
y
s are for a full
y
routed clock tree that uses the ExpressCLK input into the fast clock network. It includes both the input buffer
dela
y
and the clock routin
g
to the PFU CLK input. The dela
y
will be reduced if an
y
of the clock branches are not used.
Device
(
TJ = 85 °C, VDD = min
)
Symbol Speed Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Clock Control Timin
g
Dela
y
Throu
g
h
CLKCNTRL
(
input from corner
)
ECLKC_DEL 0.31 — 0.31 — 0.31 — 0.31 — ns
Dela
y
Throu
g
h CLKCNTRL
(
inpu t from inte r-
nal clock controller PAD
)
ECLKM_DEL 1.54 — 1.17 — 1.00 — 0.92 — ns
Clock Shutoff Timin
g
:
Setup from Middle ECLK
(
shut off to CLK
)
Hold from Middle ECLK
(
shut off from CLK
)
Setup from Corner ECLK
(
shut off to CLK
)
Hold from Corner ECLK
(
shut of f from CLK
)
OFFM_SET
OFFM_HLD
OFFC_SET
OFFC_HLD
0.77
0.00
0.77
0.00
—
—
—
—
0.51
0.00
0.51
0.00
—
—
—
—
0.44
0.00
0.44
0.00
—
—
—
—
0.41
0.00
0.41
0.00
—
—
—
—
ns
ns
ns
ns
ECLK Dela
y
(
middle pad
)
:
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
ECLKM_DEL —
—
—
—
—
—
—
3.50
3.67
—
—
—
—
—
—
2.56
2.62
2.74
2.86
3.06
—
—
—
—
—
2.05
2.08
2.13
2.19
2.29
—
—
—
—
—
1.78
1.80
1.85
1.90
1.98
ns
ns
ns
ns
ns
ECLK Dela
y
(
corner pad
)
:
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
ECLKC_DEL —
—
—
—
—
—
—
5.47
5.64
—
—
—
—
—
—
4.48
4.53
4.64
4.77
4.96
—
—
—
—
—
3.85
3.97
4.22
4.47
4.85
—
—
—
—
—
3.36
3.47
3.69
3.92
4.27
ns
ns
ns
ns
ns
FCLK Dela
y
(
middle pad
)
:
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
FCLKM_DEL —
—
—
—
—
—
—
8.24
8.87
—
—
—
—
—
—
5.91
6.12
6.59
7.11
7.98
—
—
—
—
—
4.59
4.66
4.83
5.01
5.33
—
—
—
—
—
3.81
3.89
4.06
4.26
4.59
ns
ns
ns
ns
ns
FCLK Dela
y
(
corner pad
)
:
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
FCLKC_DEL —
—
—
—
—
—
—
10.34
11.01
—
—
—
—
—
—
7.88
8.11
8.60
9.15
10.07
—
—
—
—
—
6.41
6.58
6.95
7.34
7.96
—
—
—
—
—
5.40
5.58
5.94
6.33
6.94
ns
ns
ns
ns
ns
124 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 53. General-Pur
p
ose Clock Timin
g
Characteristics
(
Internall
y
Generated Clock
)
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Notes:
This table represents the dela
y
for an internall
y
g
enerated clock from the clock tree input in one of the four middle PICs
(
usin
g
pSW routin
g)
on
an
y
side of the device which is then distributed to the PFU/PIO clock inputs. If the clock tree input used is located at an
y
other PIC, see the
results reported b
y
ORCA
Foundr
y
.
This clock dela
y
is for a full
y
routed clock tree that uses the
g
eneral clock network. The dela
y
will be reduced if an
y
of the clock branches are not
used. See pin-to-pin timin
g
in Ta ble 56 for clock dela
y
s of clocks input on
g
eneral I/O pins.
Device
(
TJ = 85 °C, VDD = min
)
Symbol Speed Unit
-4 -5 -6 -7
MinMaxMinMaxMinMaxMinMax
OR3T20 CLK_DEL — — — 4.22 — 3.46 — 2.84 ns
OR3T30 CLK_DEL — — — 4.29 — 3.48 — 2.87 ns
OR3C/T55 CLK_DEL — 5.34 — 4.41 — 3.53 — 2.93 ns
OR3C/T80 CLK_DEL — 5.49 — 4.52 — 3.57 — 2.98 ns
OR3T125 CLK_DEL — — — 4.80 — 3.71 — 3.13 ns
Lucent Technologies Inc. 125
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 54. OR3Cxx ExpressCLK to Output Delay (Pin-to-Pin)
OR3Cxx Com mer cial: VDD = 5.0 V ± 5%, 0 °C < T A < 70 °C; Indust rial: VDD = 5.0 V ± 10% , –40 °C < T A < +85 °C; CL = 50 pF.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C;CL =
50 pF.
Notes:
Timin
g
is without the use of the pro
g
rammable clock mana
g
er
(
PCM
)
.
This clock dela
y
is for a full
y
routed clock tree that uses the ExpressCLK network. It includes both the input buffer dela
y
, the clock routin
g
to the
PIO CLK input, the clock→Q of the FF, and the dela
y
throu
g
h the output buffer. The
g
iven timin
g
re
q
uires that the input clock pin be located at
one of the six ExpressCLK inputs of the dev ice, and that a PIO FF be used.
5-4846(F).a
Figure 76. ExpressCLK to Output Delay
Description
(
TJ = 85 °C, VDD = min
)
Device Speed Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
ECLK Middle Input Pin→OUTPUT Pin
(
Fast
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
9.93
10.10
—
—
—
—
—
—
7.78
7.84
7.96
8.08
8.28
—
—
—
—
—
5.40
5.43
5.48
5.54
5.64
—
—
—
—
—
4.38
4.40
4.44
4.49
4.58
ns
ns
ns
ns
ns
ECLK Middle Input Pin→OUTPUT Pin
(
Slewlim
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
12.37
12.54
—
—
—
—
—
—
9.77
9.83
9.95
10.07
10.27
—
—
—
—
—
6.07
6.10
6.15
6.21
6.31
—
—
—
—
—
4.91
4.93
4.97
5.02
5.11
ns
ns
ns
ns
ns
ECLK Middle Input Pin→OUTPUT Pin
(
Sinklim
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
13.73
13.90
—
—
—
—
—
—
11.12
11.18
11.30
11.42
11.62
—
—
—
—
—
10.92
10.95
11.00
11.06
11.16
—
—
—
—
—
9.65
9.67
9.71
9.76
9.85
ns
ns
ns
ns
ns
Addition al D el a
y
if ECLK Corner Pin Us ed OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
1.97
1.97
—
—
—
—
—
—
1.91
1.91
1.91
1.91
1.90
—
—
—
—
—
1.80
1.90
2.09
2.28
2.57
—
—
—
—
—
1.58
1.67
1.84
2.02
2.29
ns
ns
ns
ns
ns
OUTPUT (50 pF LOAD)QD
ECLK
ECLK
PIO FF
CLKCNTRL
126 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 55. OR3Cxx Fast Clock
(
FCLK
)
to Out
p
ut Dela
y
(
Pin-to-Pin
)
OR3Cxx Commercial: VDD = 5. 0 V ± 5%, 0 °C < T A < 70 °C; Industria l: VDD = 5.0 V ± 10%, –40 °C < T A < +85 °C; C L = 50 p F.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C;
CL = 50 pF.
Notes:
Timin
g
is without the use of the pro
g
rammable clock mana
g
er
(
PCM
)
.
This clock dela
y
is for a full
y
routed clock tree that uses the primar
y
clock network. It includes both the input buf fer dela
y
, the clock routin
g
to the
PIO CLK input, the clock→Q of the FF, and the dela
y
throu
g
h the output buffer. The dela
y
will be reduced if an
y
of the clock branches are not
used. The
g
iven timin
g
re
q
uires that the input clock pin be located at one of the six ExpressCLK inputs of the device and that a PIO FF be used.
5-4846(F).b
Figure 77. Fast Clock to Output Delay
Description
(
TJ = 85 °C, VDD = min
)
Device Speed Unit
-4 -5 -6 -7
MinMaxMinMaxMinMaxMinMax
Output Not on Same Side of Device As Input Clock (Fast Clock Delays Using ExpressCLK Inputs)
ECLK Middl e I npu t Pi n →OUTPUT Pin
(
Fast
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
14.68
15.30
—
—
—
—
—
—
11.13
11.35
11.81
12.33
13.20
—
—
—
—
—
7.94
8.01
8.18
8.36
8.68
—
—
—
—
—
6.40
6.48
6.66
6.85
7.19
ns
ns
ns
ns
ns
ECLK Middl e I npu t Pi n →OUTPUT Pin
(
Slewlim
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
17.11
17.74
—
—
—
—
—
—
13.12
13.33
13.80
14.32
15.19
—
—
—
—
—
8.61
8.68
8.85
9.04
9.35
—
—
—
—
—
6.93
7.01
7.19
7.38
7.72
ns
ns
ns
ns
ns
ECLK Middl e I npu t Pi n →OUTPUT Pin
(
Sinklim
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
18.47
19.10
—
—
—
—
—
—
14.47
14.68
15.15
15.67
16.54
—
—
—
—
—
13.46
13.53
13.70
13.88
14.20
—
—
—
—
—
11.67
11.75
11.93
12.12
12.46
ns
ns
ns
ns
ns
Additional Dela
y
if ECLK Corner Pin
Used OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
2.10
2.14
—
—
—
—
—
—
1.97
1.99
2.01
2.04
2.09
—
—
—
—
—
1.82
1.92
2.12
2.33
2.63
—
—
—
—
—
1.60
1.69
1.88
2.07
2.39
ns
ns
ns
ns
ns
OUTPUT (50 pF LOAD)QD
ECLK
FCLK
PIO FF
CLKCNTRL
Lucent Technologies Inc. 127
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 56. OR3Cxx General S
y
stem Clock
(
SCLK
)
to Out
p
ut Dela
y
(
Pin-to-Pin
)
OR3Cxx Com mer cial: VDD = 5.0 V ± 5%, 0 °C < T A < 70 °C; Indust rial: VDD = 5.0 V ± 10% , –40 °C < T A < +85 °C; CL = 50 pF.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C;
CL = 50 pF.
Note:
This clock dela
y
is for a full
y
routed clock tree that uses the primar
y
clock network. It includes both the input buffer dela
y
, the clock routin
g
to the
PIO CLK input, the clock→Q of the FF, and the dela
y
throu
g
h the output buffer. The dela
y
will be reduced if an
y
of the clock branches are not
used. The
g
iven timin
g
re
q
uires that the input clock pin be located at one of t he four center PICs on an
y
side of the device and that a PIO FF be
used. For clock pins located at an
y
other PIO, see the results reported b
y
ORCA
Foundr
y
.
5-4846(F)
Figure 78. System Clock to Output Delay
Description
(
TJ = 85 °C, VDD = min
)
Device Speed Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Output On Same Side of Device As Input Clock (System Clock Delays Using General User I/O Inputs)
Clock Inp ut Pi n
(
mid-PIC
)
→OUTPUT Pin
(
Fast
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
14.91
15.71
—
—
—
—
—
—
11.35
11.63
12.17
12.80
13.69
—
—
—
—
—
7.74
7.93
8.28
8.66
9.24
—
—
—
—
—
6.10
6.27
6.59
6.95
7.49
ns
ns
ns
ns
ns
Clock Input Pin
(
mid-PIC
)
→OUTPUT Pin
(
Slewlim
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
17.34
18.14
—
—
—
—
—
—
13.34
13.62
14.16
14.79
15.68
—
—
—
—
—
8.42
8.60
8.95
9.34
9.91
—
—
—
—
—
6.63
6.80
7.12
7.48
8.02
ns
ns
ns
ns
ns
Clock Input Pin
(
mid-PIC
)
→OUTPUT Pin
(
Sinklim
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
18.70
19.51
—
—
—
—
—
—
14.69
14.97
15.51
16.14
17.03
—
—
—
—
—
13.26
13.45
13.80
14.18
14.76
—
—
—
—
—
11.37
11.54
11.86
12.22
12.76
ns
ns
ns
ns
ns
Addit ion al Dela
y
if Non-mid-PIC Used as Clock
Pin OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
0.41
0.63
—
—
—
—
—
—
0.16
0.20
0.36
0.55
1.11
—
—
—
—
—
0.18
0.21
0.37
0.57
1.05
—
—
—
—
—
0.17
0.20
0.35
0.55
1.02
ns
ns
ns
ns
ns
Output Not on Same Side of Device As Input Clock (System Clock Delays Using Gene ral User I/O Inputs)
Addition al D el a
y
if Output Not on Same Side as
Input Clock Pin OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
—
—
—
—
—
0.41
0.63
—
—
—
—
—
—
0.16
0.20
0.36
0.55
1.11
—
—
—
—
—
0.18
0.21
0.37
0.57
1.05
—
—
—
—
—
0.17
0.20
0.35
0.55
1.02
ns
ns
ns
ns
ns
OUTPUT
(
50 pF LOAD
)
QD
SCLK
PIO FF
128 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 57. OR3C/Txxx In
p
ut to Ex
p
ressCLK
(
ECLK
)
Fast-Ca
p
ture Setu
p
/Hold Time
(
Pin-to-Pin
)
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Note:
The pin-to-pin timin
g
parameters in this table should be used instead of results reported b
y
ORCA
Foundr
y
.
The ECLK dela
y
s are to all of the PIOs on one side of the device for middle pin input, or two sides of the device for corner pin input. The dela
y
includes both the input buffer dela
y
and the clock routin
g
to the PIO clock input.
Description
(
TJ = 85 °C, VDD = min
)
Device Speed Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Input to ECLK Setup Time
(
middle
ECLK pin
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
1.36
1.25
—
—
—
—
—
—
1.34
1.30
1.22
1.14
1.03
—
—
—
—
—
0.88
0.86
0.83
0.80
0.76
—
—
—
—
—
0.83
0.82
0.80
0.77
0.74
—
—
—
—
—
ns
ns
ns
ns
ns
Input to ECLK Setup Time
(
middle
ECLK pin, dela
y
ed data input
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
6.91
6.79
—
—
—
—
—
—
6.30
6.27
6.19
6.11
6.00
—
—
—
—
—
5.32
5.30
5.27
5.24
5.20
—
—
—
—
—
5.98
5.97
5.95
5.93
5.90
—
—
—
—
—
ns
ns
ns
ns
ns
Input to ECLK Setup Time
(
corner
ECLK pin
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
Input to ECLK Setup Time
(
corner
ECLK pin, dela
y
ed data input
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
4.94
4.82
—
—
—
—
—
—
4.39
4.35
4.28
4.21
4.10
—
—
—
—
—
3.51
3.40
3.18
2.98
2.63
—
—
—
—
—
4.41
4.31
4.11
3.91
3.61
—
—
—
—
—
ns
ns
ns
ns
ns
Input to ECLK Hold Time
(
middle
ECLK pin
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
Input to ECLK Hold Time
(
middle
ECLK pin, dela
y
ed data input
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
Lucent Technologies Inc. 129
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 57. OR3C/Txxx In
p
ut to Ex
p
ressCLK
(
ECLK
)
Fast-Ca
p
ture Setu
p
/Hold Time
(
Pin-to-Pin
)
(continued)
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Notes:
The pin-to-pin timin
g
parameters in this table should be us ed instead of results reported b
y
ORCA
Foundr
y
.
The ECLK dela
y
s are to all of the PIOs on one side of the device for middle pin input, or two sides of the device for corner pin input. The dela
y
includes both the input buffer dela
y
and the clock routin
g
to the PIO clock input.
5-4847(F).b
Fi
g
ure 79. In
p
ut to Ex
p
ressCLK Setu
p
/Hold Time
Description
(
TJ = 85 °C, VDD = min
)
Device Speed Unit
-4 -5 -6 -7
MinMaxMinMaxMinMaxMinMax
Input to ECLK Hold Time
(
corner
ECLK pin
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.80
0.00
0.00
—
—
—
—
—
0.00
0.00
1.10
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
Input to ECLK Hold Time
(
corner
ECLK pin, dela
y
ed data input
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
QD
CLK
INPUT
PIO ECLK LATCH
CLKCNTRL
ECLK
130 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 58. OR3C/Txxx Input to Fast Clock Setup/Hold Time (Pin-to-Pin)
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Notes:
The pin-to-pin timin
g
parameters in this table should be used instead of results reported b
y
ORCA
Foundr
y
.
The FCLK dela
y
s are for a full
y
routed clock tree that uses the ExpressCLK input into the fast clock network. It includes both the input buffer
dela
y
and the clock routin
g
to the PFU CLK input. The dela
y
will be reduced if an
y
of the clock branches are not used.
Description
(
TJ = 85 °C, VDD = min
)
Device Speed Unit
-4 -5 -6 -7
MinMaxMinMaxMinMaxMinMax
Output Not on Same Side of Device As Input Clock (Fast Clock Delays Using ExpressCLK Inputs)
Input to FCLK Set up T ime
(
middle
ECLK pin
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
Input to FCLK Set up T ime
(
middle
ECLK pin, dela
y
ed data input
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.29
0.14
—
—
—
—
—
—
0.80
0.74
0.62
0.50
0.22
—
—
—
—
—
0.58
0.55
0.51
0.46
0.33
—
—
—
—
—
2.20
2.17
2.11
2.06
1.90
—
—
—
—
—
ns
ns
ns
ns
ns
Input to FCLK Setup Time
(
corner
ECLK pin
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
Input to FCLK Setup Time
(
corner
ECLK pin, dela
y
ed data input
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
Input to FCLK Hold Time
(
middle
ECLK pin
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
6.33
6.95
—
—
—
—
—
—
4.29
4.50
4.97
5.49
6.36
—
—
—
—
—
3.72
3.80
3.96
4.15
4.47
—
—
—
—
—
3.27
3.35
3.52
3.72
4.05
—
—
—
—
—
ns
ns
ns
ns
ns
Lucent Technologies Inc. 131
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 58. OR3C/Txxx Input to Fast Clock Setup/Hold Time (Pin-to-Pin) (continued)
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Notes:
The pin-to-pin timin
g
parameters in this table should be us ed instead of results reported b
y
ORCA
Foundr
y
.
The FCLK dela
y
s are for a full
y
routed clock tree that uses the ExpressCLK input into the fast clock network. It includes both the input buffer
dela
y
and the clock routin
g
to the PFU CLK input. The dela
y
will be reduced if an
y
of the clock branches are not used.
5-4847(F).a
Figure 80. Input to Fast Clock Setup/Hold Time
Description
(
TJ = 85 °C, VDD = min
)
Device Speed Unit
-4 -5 -6 -7
MinMaxMinMaxMinMaxMinMax
Input to FCLK Hold Time
(
middle
ECLK pin, dela
y
ed data input
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
Input to FCLK Hold Time
(
corner
ECLK pin
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
8.43
9.09
—
—
—
—
—
—
6.26
6.49
6.98
7.53
8.45
—
—
—
—
—
5.54
5.72
6.09
6.47
7.10
—
—
—
—
—
4.88
5.04
5.40
5.79
6.40
—
—
—
—
—
ns
ns
ns
ns
ns
Input to FCLK Hold Time
(
corner
ECLK pin, dela
y
ed data input
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
QD
ECLK
INPUT
PIO FF
CLKCNTRL
FCLK
132 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 59. OR3C/Txxx Input to General System Clock (SCLK) Setup/Hold Time (Pin-to-Pin)
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Notes:
The pin-to-pin timin
g
parameters in this table should be used instead of results reported b
y
ORCA
Foundr
y
.
This clock dela
y
is for a full
y
routed clock tree that uses the clock network. It includes both the input buffer dela
y
and the clock routin
g
to the PIO
FF CLK input. The dela
y
will be reduced if an
y
of the clock branches are not used. The
g
iven setup
(
dela
y
ed and no dela
y)
and hold
(
dela
y
ed
)
timin
g
allows the input clock pin to be located in an
y
PIO on an
y
side of the device, but a PIO FF must be used. The hold
(
no dela
y)
timi n
g
assumes the clock pin is located at one of the four middle PICs on an
y
side of the device and that a PIO FF is used. If the clock pin is located
elsewhere, then the last parameter in the table must be added to the hold
(
no dela
y)
timin
g
.
5-4847(F)
Figure 81. Input to System Clock Setup/Hold Time
Description
(
TJ = 85 °C, VDD = min
)
Device Speed Unit
-4 -5 -6 -7
Min Max Min Max Min Max Min Max
Input to SCLK Setup Time OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
Input to SCLK Setup Time
(
dela
y
ed data input
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.99
0.79
—
—
—
—
—
—
1.33
1.22
1.09
0.93
0.78
—
—
—
—
—
1.47
1.40
1.33
1.26
1.19
—
—
—
—
—
3.09
3.03
2.97
2.91
2.86
—
—
—
—
—
ns
ns
ns
ns
ns
Input to SCLK Hold Time OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
6.82
7.62
—
—
—
—
—
—
4.74
5.01
5.56
6.19
7.07
—
—
—
—
—
3.64
3.83
4.18
4.56
5.14
—
—
—
—
—
3.04
3.22
3.54
3.89
4.44
—
—
—
—
—
ns
ns
ns
ns
ns
Input to SCLK Hold Time
(
dela
y
ed data input
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.00
0.00
—
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
0.00
0.00
0.00
0.00
0.00
—
—
—
—
—
ns
ns
ns
ns
ns
Additional Hold Time if Non-
mid-PIC Used as SCLK Pi n
(
no dela
y
on data input
)
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
—
—
0.41
0.63
—
—
—
—
—
—
0.16
0.20
0.36
0.55
1.11
—
—
—
—
—
0.18
0.21
0.37
0.57
1.05
—
—
—
—
—
0.17
0.20
0.35
0.55
1.02
—
—
—
—
—
ns
ns
ns
ns
ns
QD
SCLK
INPUT
PIO FF
Lucent Technologies Inc. 133
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Configur ation Timing
Table 60. General Configuration Mode Timing Characteristics
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
* Not applicable to as
y
nchronous peripheral mode.
Parameter Symbol Min Max Unit
All Configuration Modes
M
[
3:0
]
Setup Time to INIT Hi
g
hTSMODE0.00—ns
M
[
3:0
]
Hold Time from INIT Hi
g
h THMODE 600.00 — ns
RESET Pulse Width Low to Start Reconfi
g
uration TRW 50.00 — ns
PRGM Pulse Width Low to Start Reconfi
g
uration TPGW 50.00 — ns
Master and As
y
nchronous Peripheral Modes
Power-on Reset Dela
y
CCLK Period
(
M3 = 0
)
(
M3 = 1
)
Confi
g
uration Latenc
y
(
autoincrement mode
)
:
OR3T20
(
M3 = 0
)
(
M3 = 1
)
OR3T30
(
M3 = 0
)
(
M3 = 1
)
OR3C/T55
(
M3 = 0
)
(
M3 = 1
)
OR3C/T80
(
M3 = 0
)
(
M3 = 1
)
OR3T125
(
M3 = 0
)
(
M3 = 1
)
TPO
TCCLK
TCL
15.70
60.00
480.00
11.50
92.10
15.10
121.00
23.20
185.00
33.70
270.00
52.30
418.00
52.40
200.00
1600.00
38.40*
307.00*
50.40*
403.30*
77.40*
619.00*
113.00*
900.00*
175.00*
1395.00*
ms
ns
ns
ms
ms
ms
ms
ms
ms
ms
ms
ms
ms
Microprocessor (MPI) Mode
Power-on Reset Dela
y
Confi
g
uration Latenc
y
(
autoincrement mode
)
:
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
TPO
TCL 15.70
27413
35445
53341
76317
116581
52.40
—
—
—
—
—
ms
write c
y
cles
write c
y
cles
write c
y
cles
write c
y
cles
write c
y
cles
Partial Reconfi
g
uration
(
explicit mode
)
:
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
TPR 32
36
43
51
62
—
—
—
—
—
write c
y
cles
write c
y
cles
write c
y
cles
write c
y
cles
write c
y
cles
Slave Serial Mode
Power-on Reset Dela
y
CCLK Period
OR3Cxx
OR3Txxx
Confi
g
uration Latenc
y
(
autoincrement mode
)
:
OR3T20
OR3T30
OR3C55
OR3T55
OR3C80
OR3T80
OR3T125
TPO
TCCLK
TCL
3.90
40
15
2.80
3.80
15.50
5.80
22.50
8.40
13.09
13.10
—
—
—
—
—
—
—
—
—
ms
ns
ns
ms
ms
ms
ms
ms
ms
ms
134 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (con tinued)
Table 60. General Confi
g
uration Mode Timin
g
Characteristics (continued)
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Note: TPO is tri
gg
ered when VDD reaches between 3.0 V to 4.0 V for the OR 3Cxx and between 2.7 V and 3.0 V for the OR3Txxx.
Parameter Symbol Min Max Unit
Slave Parallel Mode
Power-on Reset Dela
y
CCLK Period:
OR3Cxx
OR3Txxx
Confi
g
uration Late nc
y
(
normal mode
)
:
OR3T20
OR3T30
OR3C55
OR3T55
OR3C80
OR3T80
OR3T125
TPO
TCCLK
TCL
3.90
40.00
15.00
0.36
0.47
1.94
0.72
2.81
1.05
1.64
13.10
—
—
—
—
—
—
—
—
—
ms
ns
ns
ms
ms
ms
ms
ms
ms
ms
Partial Reconfi
g
uration
(
explicit mode
)
:
OR3T20
OR3T30
OR3C55
OR3T55
OR3C80
OR3T80
OR3T125
TPR 0.48
0.54
1.72
0.65
2.04
0.77
0.93
—
—
—
—
—
—
—
µ
s/frame
µ
s/frame
µ
s/frame
µ
s/frame
µ
s/frame
µ
s/frame
µ
s/frame
INIT Timin
g
INIT Hi
g
h to CCLK Dela
y
:
Slave Parallel
Slave Serial
Master Serial:
(
M3 = 1
)
(
M3 = 0
)
Master Parallel:
(
M3 = 1
)
(
M3 = 0
)
TINIT_CCLK 1.00
1.00
1.00
0.50
4.80
1.00
—
—
3.40
2.00
16.20
3.60
µ
s
µ
s
µ
s
µ
s
µ
s
µ
s
Initialization Latenc
y
(
PRGM hi
g
h to INIT hi
g
h
)
:
OR3T20
OR3T30
OR3C/T55
OR3C/T80
OR3T125
TIL 0.21
0.24
0.30
0.36
0.45
0.68
0.79
1.00
1.20
1.50
ms
ms
ms
ms
ms
INIT Hi
g
h to WR, As
y
nchronous Peripheral TINIT_WR 2.00 —
µ
s
Lucent Technologies Inc. 135
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
5-4531(F)
Figure 82. General Configuration Mode Timing Diagram
VDD
CCLK
M[3:0]
PRGM
INIT
TPO + TIL
TIL
TCCLK
TSMODE THMODE
TINIT_CLK
DONE TCL
TPGW
136 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (con tinued)
Table 61. Master Serial Confi
g
uration Mode Timin
g
Characteri stics
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
* Data
g
ets clocked out from an external serial ROM. The clock to data dela
y
of the serial ROM must be les s than the CCLK fre
q
uenc
y
since
the data available out of the serial ROM must be setup and waitin
g
to be clocked into the FPGA before the next CCLK risin
g
ed
g
e.
Note: Serial confi
g
uration data is transmitted out on DOUT on the fallin
g
ed
g
e of CCLK after it is input on DIN.
5-4532(F)
Figure 83. Master Serial Configuration Mode Timing Diagram
Parameter S
y
mbol Min Max Unit
DIN Setup Time* TS60.00 — ns
DIN Hold Time TH0.00 — ns
CCLK Fre
q
uenc
y
(
M3 = 0
)
FC5.00 16.67 MHz
CCLK Fre
q
uenc
y
(
M3 = 1
)
FC0.63 2.08 MHz
CCLK to DOUT Dela
y
TD—5.00ns
DIN
CCLK
DOUT
TSTH
BIT N
TD
BIT N
Lucent Technologies Inc. 137
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 62. Master Parallel Confi
g
uration Mode Timin
g
Characteristics
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Notes:
The RCLK period consists of seven CCLKs for RCLK low and one CCLK for RCLK hi
g
h.
Serial data is transmitted out on DOUT 1.5 CCLK c
y
cles after the b
y
te is input on D[7:0].
5-6764(F)
Figure 84. Master Parallel Configuration Mode Timing Diagram
Parameter S
y
mbol Min Max Unit
RCLK to Address Valid TAV — 60.00 ns
D
[
7:0
]
Setup Time to RCLK Hi
g
hT
S60.00 — ns
D
[
7:0
]
Hold Time to RCLK Hi
g
hT
H0.00 — ns
RCLK Low Time
(
M3 = 0
)
TCL 7.00 7.00 CCLK c
y
cles
RCLK Hi
g
h Time
(
M3 = 0
)
TCH 1.00 1.00 CCLK c
y
cles
RCLK Low Time
(
M3 = 1
)
TCL 7.00 7.00 CCLK c
y
cles
RCLK Hi
g
h Time
(
M3 = 1
)
TCH 1.00 1.00 CCLK c
y
cles
CCLK to DOUT TD—5.00ns
A[17:0]
RCLK
D[7:0]
TCL
TCH
TAV
CCLK
DOUT
TH
TS
BYTE N BYTE N + 1
D0 D1 D2 D3 D4 D5 D6 D7
TD
138 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 63. As
y
nchronous Peri
p
heral Confi
g
uration Mode Timin
g
Characteristics
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
* This parameter is valid whether the end of not RDY is determined from the RDY pin or from the D7 pin.
Notes:
Serial data is transmitted out on DOUT on the fallin
g
ed
g
e of CCLK after the b
y
te is input on D[7:0].
D[6:0] timin
g
is the same as the write data portion of the D7 waveform because D[6:0] are not enabled b
y
RD.
5-4533(F)
Figure 85. Asynchronous Peripheral Configuration Mode Timing Diagram
Parameter Symbol Min Max Unit
WR, CS0, and CS1 Pulse Width T WR 50.00 — ns
D
[
7:0
]
Setup Time:
3Cxx
3Txxx
TS20.00
10.50 —
—ns
ns
D
[
7:0
]
Hold Time TH0.00 — ns
RDY Dela
y
TRDY — 40.00 ns
RDY Low TB1.00 8.00 CCLK Periods
Earliest WR After RDY Goes Hi
g
h* TWR2 0.00 — ns
RD to D7 Enable/Disable TDEN — 40.00 ns
CCLK to DOUT TD—5.00ns
CS1
D7
CCLK
DOUT
CS0
RDY
D0 D1 D2
TB
TWR
TSTH
TRDY
WR
D7
TD
PREVIOUS BYTE
TWR2
WRITE DATA
D3
TDEN TDEN
RD
Lucent Technologies Inc. 139
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Table 64. Slave Serial Configuration Mode Timing Characteristics
OR3Cxx Commercial: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Note: Serial confi
g
uration data is transmitted out on DOUT on the fallin
g
ed
g
e of CCLK after it is input on DIN.
5-4535(F).
Figure 86. Slave Serial Configuration Mode Timing Diagram
Parameter S
y
mbol Min Max Unit
DIN Setu p Time:
3Cxx
3Txxx
TS20.00
10.50 —
—ns
ns
DIN Hold Time TH0.00 — ns
CCLK Hi
g
h Time:
3Cxx
3Txxx
TCH 20.00
7.00 —
—ns
ns
CCLK Low Time:
3Cxx
3Txxx
TCL 20.00
7.00 —
—ns
ns
CCLK Fre
q
uenc
y
:
3Cxx
3Txxx
FC—
—25.00
66.00 MHz
MHz
CCLK to DOUT TD— 20.00 ns
DIN
CCLK
DOUT
TD
TSTH
TCL TCH
BIT N
BIT N
140 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (con tinued)
Table 65. Slave Parallel Configuration Mode Timing Characteristics
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
Note: Dais
y
-chainin
g
of FPGAs is not supported in this mode.
5-2848(F)
Figure 87. Slave Parallel Configuration Mode Timing Diagram
Parameter S
y
mbol Min Max Unit
CS0, CS1, WR Setup Time TS1 40.00 — ns
CS0, CS1, WR Hold Time TH1 20.00 — ns
D
[
7:0
]
Setup Time:
3Cxx
3Txxx
TS2 20.00
7.00 —
—ns
ns
D
[
7:0
]
Hold Time TH2 0.00 — ns
CCLK Hi
g
h Time:
3Cxx
3Txxx
TCH 20.00
7.00 —
—ns
ns
CCLK Low Time:
3Cxx
3Txxx
TCL 20.00
7.00 —
—ns
ns
CCLK Fre
q
uenc
y
:
3Cxx
3Txxx
FC—
—25.00
66.00 MHz
MHz
TS1
TS2 TH2
CS1
CCLK
D[7:0]
CS0
WR
TCL TCH
TH1
Lucent Technologies Inc. 141
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (continued)
Microprocessor Interface (MPI) Configuration Timing Characteristics
For configuration timing using the MPI, consult Table 49. See Figures 67 through 74 for MPI timing diagrams.
142 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Timing Characteristics (con tinued)
Readback Timing
Table 66. Readback Timin
g
Characteri stics
OR3Cxx Commerci al: VDD = 5.0 V ± 5%, 0 °C < TA < 70 °C; Industrial: VDD = 5.0 V ± 10%, –40 °C < TA < +85 °C.
OR3Txxx Commercial: VDD = 3.0 V to 3.6 V, 0 °C < TA < 70 °C; Industrial: VDD = 3.0 V to 3.6 V, –40 °C < TA < +85 °C.
5-4536(F)
Figure 88. Readback Timing Diagram
Parameter S
y
mbol Min Max Unit
RD_CFG to CCLK Setup Time TS50.00 — ns
RD_CFG Hi
g
h Width to Abort Readback TRBA 2 — CCLK c
y
cles
CCLK Low Time TCL 40.00 — ns
CCLK Hi
g
h Time TCH 40.00 — ns
CCLK Fre
q
uenc
y
FC— 12.50 MHz
CCLK to RD_DATA Dela
y
TD— 40.00 ns
TD
TCH
CCLK
RD_DATA
TSTCL
RD_CFG
BIT 0 BIT 1 BIT 0
TRBA
Lucent Technologies Inc. 143
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Input/Output Buffer Measurement Conditions
Note: Switch to VDD for TPLZ/TPZL; switch to GND for TPHZ/TPZH.5-3234(F)
Figure 89. ac Test Loads
5-3233.a(F)
Fi
g
ure 90. Out
p
ut Buffer Dela
y
s
5-3235(F)
Fi
g
ure 91. In
p
ut Buffer Dela
y
s
50 pF
A. Load Used to Measure Propagation Delay
TO THE OUTPUT UNDER TEST
TO THE OUTPUT UNDER TEST
50 pF
V
CC
GND
1 k
Ω
B. Load Used to Measure Rising/Falling Edges
VDD
TPHH
VDD/2
VSS
out[i]
PAD
OUT 1.5 V
0.0 V TPLL
PAD
out[i] ac TEST LO ADS (SHOWN ABO VE )
ts[i]
OUT
0.0 V
1.5 V
TPHH TPLL
PAD in[i]
IN
3.0 V
VSS
VDD/2
VDD
PAD IN
in[i]
144144 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Output Buffer Characteristics
OR3Cxx
5-4634(F)
Fi
g
ure 92. Sinklim
(
TJ = 25 °C, VDD = 5.0 V
)
5-4636(F)
Fi
g
ure 93. Slewlim
(
TJ = 25 °C, VDD = 5.0 V
)
5-4638(F)
Fi
g
ure 94. Fast
(
TJ = 25 °C, VDD = 5.0 V
)
5-4635(C)
Fi
g
ure 95. Sinklim
(
TJ = 125 °C, VDD = 4.5 V
)
5-4637(F)
Fi
g
ure 96. Slewlim
(
TJ = 125 °C, VDD = 4.5 V
)
5-4639(F)
Fi
g
ure 97. Fast
(
TJ = 125 °C, VDD = 4.5 V
)
70
60
50
40
30
20
10
0
OUTPUT CURRENT, I
O
(mA)
012345
OUTPUT VOLTAGE, VO (V)
IOL
IOH
250
225
150
100
50
0
OUTPUT CU RR ENT, I
O
(mA)
01234
OUTPUT VOLTAGE, V
O
(V)
I
OL
I
OH
5
200
175
125
75
25
250
225
150
100
50
0
OUTPUT CURRENT, I
O
(mA)
01234
OUTPU T VOLTAG E , V
O
(V)
I
OL
I
OH
5
200
175
125
75
25
50
40
30
20
10
0
OUTPUT CURRENT, I
O
(mA)
01 234
OUTPUT VOLTA G E, V
O
(V)
I
OL
I
OH
5
150
125
100
75
50
0
OUTPUT CU RRE NT, I
O
(mA)
0123 4
OUTPUT VOLTAGE, V
O
(V)
I
OL
I
OH
25
175
125
100
75
50
0
OUTP UT CURRENT, I
O
(mA)
01 23 4
OUTPUT VO LTAGE, V
O
(V)
I
OL
I
OH
25
150
Lucent Technologies Inc. 145
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Output Buffer Characteristics (continued)
OR3Txxx
5-6865(F)
Fi
g
ure 98. Sinklim
(
TJ = 25 °C, VDD = 3.3 V
)
5-6967(F)
Fi
g
ure 99. Slewlim
(
TJ = 25 °C, VDD = 3.3 V
)
5-6867(F)
Fi
g
ure 100. Fast
(
TJ = 25 °C, VDD = 3.3 V
)
5-6866(F)
Fi
g
ure 101. Sinklim
(
TJ = 125 °C, VDD = 3.0 V
)
5-6868(F)
Fi
g
ure 102. Slewlim
(
TJ = 125 °C, VDD = 3.0 V
)
5-6868(F)
Fi
g
ure 103. Fast
(
TJ = 125 °C, VDD = 3.0 V
)
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
0
20
40
60
110
OUTPUT VOLTAGE, VO (V)
IOL
70
50
30
10
IOH
OUTPUT CURRENT, IO (mA)
80
90
100
0.0 0.5 1.0 1.5 2.0 2.5 3.0
0
40
80
OUTPUT VOLTAGE, VO (V)
IOL
100
60
20
IOH
OUTPUT CURRENT, IO (mA)
120
140
3.5
0.0 0.5 1.0 1.5 2.0 2.5 3.0
0
40
80
OUTPU T VOLTAGE, V
O
(V)
I
OL
100
60
20
I
OH
OUTPUT CURRENT, I
O
(mA)
120
140
3.5
0.0 0.5 1.0 1.5 2.0 2.5 3.0
0
20
40
60
OUTPUT VOLTAGE, VO (V)
IOL
70
50
30
10
IOH
OUTPUT CURRENT , IO (mA)
80
90
0.0 0.5 1.0 1.5 2.0 2.5 3.0
0
40
80
OUTPUT VOLTAGE, VO (V)
IOL
100
60
20
IOH
OUTPUT CURRENT, IO (mA)
120
0.0 0.5 1.0 1.5 2.0 2.5 3.0
0
40
80
OUTPUT VOL TAGE, V
O
(V)
I
OL
100
60
20
I
OH
OUTPU T CURRENT, I
O
(mA)
120
146146 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Estimating Power Dissipation
OR3Cxx
The total operating power dissipated is estimated by
summing the standby (IDDSB), internal, and external
power dissipated. The internal and external power is
the power consumed in the PLCs and PICs, respec-
tively. In general, the standby power is small and may
be neglected. The total operating power is as follows:
PT = Σ PPLC + Σ PPIC
The internal operating power is made up of two parts:
clock generation and PFU output power. The PFU out-
put power can be estimated based upon the number of
PFU outputs s witching when driving an a verage f an-out
of two:
PPFU = 0.136 mW/MHz
For each PFU output that switches, 0.136 mW/MHz
needs to be multiplied times the frequency (in MHz)
that the output switches. Generally, this can be esti-
mated by using one-half the clock rate, multiplied by
some activity factor; for example, 20%.
The power dissipated b y the clock generation circuitry
is based upon four parts: the fixed clock power, the
power/clock branch row or column, the cloc k power dis-
sipated in each PFU that uses this particular clock, and
the power from the subset of those PFUs that are con-
figured as synchronous memory. Therefore, the clock
power can be calculated for the four parts using the fol-
lowing equations :
OR3C55 Clock Power
P=
[
0.183 mW/MHz
+
(
0.235 mW/MHz/Branch
)
(
# Branches
)
+
(
0.033 mW/MHz/PFU
)
(
# PFUs
)
+
(
0.008 mW/MHz/PIO
(
# PIOs
)]
For a quick estimate, the worst-case (typical circuit)
OR3C55 cloc k power ≈ 14.64 mW/MHz.
OR3C80 Clock Power
P=
[
0.224 mW/MHz
+
(
0.288 mW/MHz/Branch
)
(
# Branches
)
+
(
0.033 mW/MHz/PFU
)
(
# PFUs
)
+
(
0.008 mW/MHz/PIO
(
# PIOs
)]
For a quick estimate, the worst-case (typical circuit)
OR3C80 cloc k power ≈ 21.06 mW/MHz.
The power dissipated in a PIC is the sum of the power
dissipated in the four PIOs in the PIC. This consists of
power dissipated by inputs and ac power dissipated by
outputs. The power dissipated in each PIO depends on
whether it is configured as an input, output, or input/
output. If a PIO is operating as an output, then there is
a power dissipation component for PIN, as well as
POUT. This is because the output feeds back to the
input.
The power dissipated by a TTL input b uff er is estimated
as:
PTTL = 2.2 mW + 0.17 mW/MHz
The power dissipated by an input buff er is estimated
as:
PCMOS = 0.17 mW/MHz
The ac power dissipation from an output or bidirec-
tional is estimated by the following:
POUT =
(
CL + 8.8 pF
)
x VDD2 x F Watts
where the unit for CL is farads, and the unit f or F is Hz.
As an example of estimating power dissipation, sup-
pose that a fully utilized OR3C55 has an average of
six outputs for each of the 324 PFUs, that 10 clock
branches are used so that the clock is driven to the
entire PLC array, that 150 of the 324 PFUs have FFs
clocked at 40 MHz, and that the PFU outputs have an
average activity factor of 20%.
Twenty TTL-configured inputs, 20 CMOS-configured
inputs, 32 outputs driving 30 pF loads, and 16 bidirec-
tional I/Os driving 50 pF loads are also generated from
the 40 MHz clock with an average activity factor of
20%. All of the output PIOs are registered, and 30 of
the input PIOs are registered. The worst-case (VDD =
5.25 V) power dissipation is estimated as follows:
PPFU = 324 x 6
(
0.136 mW/MHz x 20 MHz x 20%
)
= 1057.54 mW
PCLK =
[
0.183 mW/MHz +
(
0.235 mW/MHz – Branch
)
(
10 Branches
)
+
(
0.033 mW/MHz – PFU
)
(
150 PFUs
)
+
(
0.008 mW/MHz/PIO
(
58 PIOs
)]
= 317.88 mW
PTTL = 20 x
[
2.2 mW +
(
0.17 mW/MHz x 20 MHz x 20%
)]
= 57.6 mW
PCMOS = 20 x
[
0.17 mW x 20 MH z x 20%
]
= 13.6 mW
POUT = 32 x
[(
30 pF + 8.8 pF
)
x
(
5.25
)
2 x 20 MHz x 20%
]
=136.89 mW
PBID = 16 x
[(
50 pF + 8.8 pF
)
x
(
5.25
)
2 x 20 MHz x 20%
]
= 103.72 mW
Total = 1.69 W
Lucent Technologies Inc. 147
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Estimating Power Dissipation (continued)
OR3Txxx (Preliminary Information)
The total operating power dissipated is estimated by
summing the standby (IDDSB), internal, and external
power dissipated. The internal and external power is
the power consumed in the PLCs and PICs, respec-
tively. In general, the standby power is small and may
be neglected. The total operating power is as follows:
PT = Σ PPLC + Σ PPIC
The internal operating power is made up of two parts:
clock generation and PFU output power. The PFU out-
put power can be estimated based upon the number of
PFU outputs s witching when driving an a verage f an-out
of two:
PPFU = 0.068 mW/MHz
For each PFU output that switches, 0.068 mW/MHz
needs to be multiplied times the frequency (in MHz)
that the output switches. Generally, this can be esti-
mated by using one-half the clock rate, multiplied by
some activity factor; for example, 20%.
The power dissipated by the clock generation circuitry
is based upon four parts: the fixed clock power, the
power/clock branch row or column, the cloc k power dis-
sipated in each PFU that uses this particular clock, and
the power from the subset of those PFUs configured as
synchronous memory. Therefore, the clock power can
be calculated for the four parts using the following
equations.
OR3T20 Clock Power
P=
[
0.38 mW/MHz
+
(
0.045 mW/MHz/Branch
)
(
# Branches
)
+
(
0.015 mW/MHz/PFU
)
(
# PFUs
)
+
(
0.004 mW/MHz/PIO
(
# PIOs
)]
For a quick estimate , the worst-case (typical circuit)
OR3T20 clock po wer ≈ 2.92 mW/MHz.
OR3T30 Clock Power
P=
[
0.53 mW/MHz
+
(
0.061 mW/MHz/Branch
)
(
# Branches
)
+
(
0.015 mW/MHz/PFU
)
(
# PFUs
)
+
(
0.004 mW/MHz/PIO
(
# PIOs
)]
For a quick estimate , the worst-case (typical circuit)
OR3T30 clock po wer ≈ 3.98 mW/MHz.
OR3T55 Clock Power
P=
[
0.88 mW/MHz
+
(
0.102 mW/MHz/Branch
)
(
# Branche s
)
+
(
0.015 mW/MHz/PFU
)
(
# PFUs
)
+
(
0.004 mW/MHz/PIO
(
# PIOs
)]
For a quick estimate , the worst-case (typical circuit)
OR3T55 clock po wer ≈ 6.58 mW/MHz.
OR3T80 Clock Power
P=
[
0.107 mW/MHz
+
(
0.124 mW/MHz/Branch
)
(
# Branche s
)
+
(
0.015 mW/MHz/PFU
)
(
# PFUs
)
+
(
0.004 mW/MHz/PIO
(
# PIOs
)]
For a quick estimate , the worst-case (typical circuit)
OR3T80 clock po wer ≈ 9.47 mW/MHz.
OR3T125 Clock Power
P=
[
0.167 mW/MHz
+
(
0.193 mW/MHz/Branch
)
(
# Branche s
)
+
(
0.015 mW/MHz/PFU
)
(
# PFUs
)
+
(
0.004 mW/MHz/PIO
(
# PIOs
)]
For a
q
uick estimate, the worst-case
(
t
y
pical circuit
)
OR3T125 clock power ≈ 15.44 mW/MHz.
The power dissipated in a PIC is the sum of the power
dissipated in the four PIOs in the PIC. This consists of
power dissipated by inputs and ac power dissipated by
outputs. The power dissipated in each PIO depends on
whether it is configured as an input, output, or input/
output. If a PIO is operating as an output, then there is
a power dissipation component for PIN, as well as
POUT. This is because the output feeds back to the
input.
The power dissipated by an input buff er (VIH = VDD –
0.3 V or higher) is estimated as:
PIN = 0.09 mW/MHz
The ac power dissipation from an output or bidirec-
tional is estimated by the following:
POUT =
(
CL + 8.8 pF
)
x VDD2 x F Watts
where the unit for CL is farads, and the unit f or F is Hz.
148 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Estimating Power Dissipation (continued)
As an example of estimating power dissipation, suppose that a fully utilized OR3T80 has an average of
six outputs for each of the 484 PFUs, that 12 clock branches are used so that the cloc k is driven to the entire PLC
array, that 250 of the 484 PFUs have FFs clocked at 40 MHz, and that the PFU outputs have an average activity
factor of 20%.
Eighty inputs, 40 of them used as 5 V tolerant inputs, 50 outputs driving 30 pF loads, and 30 bidirectional
I/Os driving 50 pF loads are also generated from the
40 MHz cloc k with an average activity factor of 20%. All of the output PIOs are registered, and 30 of the input PIOs
are registered.
The worst-case (VDD = 3.6 V) power dissipation is estimated as follows:
PPFU = 484 x 6
(
0.068 mW/MHz x 20 MHz x 20%
)
= 789.9 mW
PCLK =
[
0.107 mW/MHz +
(
0.09 mW/MHz – Branch
)
(
12 Branches
)
+
(
0.015 mW/MHz – PFU
)
(
250 PFUs
)
+
(
0.004 mW/MHz /PIO
)
(
110 PIOs
)]
= 230.43 mW
PIN = 80 x
[
0.09 mW/MHz x 20 MHz x 20%
]
= 28.8 mW
POUT = 50 x
[(
30 pF + 8.8 pF
)
x
(
3.6
)
2 x 20 MHz x 20%
]
= 100.57 mW
PBID = 30 x
[(
50 pF + 8.8 pF
)
x
(
3.6
)
2 x 20 MHz x 20%
]
= 91.45 mW
TOTAL = 1.241 W
Lucent Technologies Inc. 149
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Pin Inform ation
Pin Desc riptions
This section describes the pins f ound on the Series 3 FPGAs. Any pin not described in this table is a user-program-
mable I/O . During configuration, the user-programmable I/Os are 3-stated with an internal pull-up resistor enab led.
If any pin is not used (or not bonded to a package pin), it is also 3-stated with an internal pull-up resistor enabled
after configuration.
Table 67. Pin Descriptions
S
y
mbol I/O Descri
p
tion
Dedicated Pins
VDD — Positive power suppl
y
.
GND — Ground suppl
y
.
VDD5 — 5 V tolerant select. VDD5 pin locations are shown for packa
g
e compat ibi lit
y
with
OR2TxxA devices. Connections to 5 V power sources are not used for 5 V tolerant
I/Os in the OR3Txxx devices.
RESET IDurin
g
confi
g
uration, RESET forces the restart of confi
g
uration and a pull-up is
enabled. After confi
g
uration, RESET can be used as a
g
eneral FPG A inp ut or as a
direct input, which causes all PLC latches/FFs to be as
y
nchronousl
y
set/res et.
CCLK I In the master and as
y
nchronous peripheral modes, CCLK is an output which
strobe s confi
g
uration data in. In the slave or s
y
nchronous peripheral mode, CCLK
is input s
y
nchronous with the data on DIN or D
[
7:0
]
. In microprocessor mode, CCLK
is used internall
y
and output for dais
y
-chain operation.
DONE I
O
As an input, a low level on DONE dela
y
s FPGA start-up after confi
g
uration
(
see
Note
)
.
As an act ive-h i
g
h, open-drain output, a hi
g
h level on this si
g
nal indicates that confi
g
-
uration is complete. DONE has an optional pull-up resistor.
PRGM IPRGM is an active-low input that forces the restart of confi
g
uration and resets the
boundar
y
-scan circ uitr
y
. This pin alwa
y
s has an active pull-up.
RD_CFG I This pin must be held hi
g
h durin
g
device initialization until the INIT pin
g
oes hi
g
h.
This pin alwa
y
s has an active pull-up.
Durin
g
confi
g
uration, RD_CFG is an active-low input that activates the TS_ALL func-
tion and 3-states all of the I/O.
After confi
g
uration, RD_CFG can be selected
(
via a bit stream option
)
to activate the
TS_ALL function as described above, or, if readback is enabled via a bit stream
option, a hi
g
h-to-low transition on RD_CFG will initiate readback of the confi
g
uration
data, includin
g
PFU output states, startin
g
with frame address 0.
RD_DATA/TDO O RD_DATA/TDO is a dual-function pin. If used for readback, RD_DATA provides con-
fi
g
uration data out. If used in boundar
y
scan, TDO is test data out.
S
p
ecial-Pur
p
ose Pins
M0, M1, M2 I
I/O
Durin
g
powerup and initialization, M0—M2 are used to select the confi
g
uration
mode with their values latched on the risin
g
ed
g
e of INIT; see Table 34 for the confi
g
-
uratio n mode s. Dur in
g
confi
g
uration, a pull-up is enabled.
After co nfi
g
uration, these pins are user-pro
g
rammable I/O
(
see Note
)
.
Note: The FPGA States of Operation section contains more information on how to control these si
g
nals durin
g
start-up. The tim in
g
of DONE
release is controlled b
y
one set of bit stream options, and the timin
g
of the simultaneous release of all ot her confi
g
uration pins
(
and the
activation of all user I/Os
)
is controlled b
y
a second set of options.
150 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Pin Information (continued)
Table 67. Pin Descriptions
(
continued
)
S
y
mbol I/O Descri
p
tion
S
p
ecial-Pur
p
ose Pins
(
continued
)
M3 I
I/O
Durin
g
powerup and initialization, M3 is used to select the speed of the internal oscillator dur-
in
g
confi
g
uration with their values latched on the risin
g
ed
g
e of INIT. When M3 is low, the
oscillator fre
q
uenc
y
is 10 MHz. When M3 is hi
g
h, the oscillator is 1.25 MHz. Durin
g
confi
g
ura-
tion, a pull-up is enabled.
After confi
g
uration, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
TDI, TCK,
TMS I
I/O
If boundar
y
scan is used, these pins are test data in, test clock, and test mode select inputs. If
boundar
y
scan is not selected, all boundar
y
-sca n funct ions ar e inhib ited on ce confi
g
uration is
complete. Even if boundar
y
scan is not used, either TCK or TMS must be held at lo
g
ic 1 dur-
in
g
confi
g
uration. Each pin has a pull-up enabled durin
g
confi
g
uration.
After confi
g
uration, these pins are user-pro
g
rammable I/O
(
see Note
)
.
RDY/RCLK/
MPI_ALE O
O
I
I/O
Durin
g
confi
g
uration in peripheral mode, RDY/RCLK indicates another b
y
te can be written to
the FPGA. If a read operation is done when the device is selected, the same status is also
available on D7 in as
y
nchronous peripheral mode.
Durin
g
the master parallel confi
g
uration mode, RCLK is a read output si
g
nal to an external
memor
y
. This output is not normall
y
used.
In
i960
microprocessor mode, this pin acts as the address latch enable
(
ALE
)
input.
After confi
g
uration, if the MPI is not used, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
HDC O
I/O
Hi
g
h Durin
g
Confi
g
uration is output hi
g
h until confi
g
uration is complete. It is used as a control
output, indic ati n
g
that confi
g
uration is not complete.
After confi
g
uration, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
LDC O
I/O
Low Durin
g
Confi
g
uration is output low until confi
g
uration is complete. It is used as a control out-
put, indicatin
g
that confi
g
uration is not complete.
After confi
g
uration, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
INIT I/O
I/O
INIT is a bidirectional si
g
nal before and durin
g
confi
g
urat i on . Du r in
g
confi
g
uration, a pull-up is
enabled, but an external pull-up resistor is recommended. As an active-low open-drain out-
put, INIT is held low durin
g
power stabilization and internal clearin
g
of memor
y
. As an active-
low input, INIT holds the FPGA in the wait-state before the start of confi
g
uration.
After confi
g
uration, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
Note: The FPGA States of Operation section contains more information on how to control these si
g
nals durin
g
start-up. The timin
g
of DONE
release is controlled b
y
one set of bit stream options, and the timin
g
of the simultaneous release of all other confi
g
uration pins
(
and the
activation of all user I/Os
)
is controlled b
y
a second set of options.
Lucent Technologies Inc. 151
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
S
p
ecial-Pur
p
ose Pins
(
continued
)
CS0, CS1 I
I/O
CS0 and CS1 are used in the as
y
nchronous peripheral, slave parallel, and microprocessor
confi
g
uration modes. The FPGA is selected when CS0 is low and CS1 is hi
g
h. Durin
g
confi
g
-
uration, a pull-up is enabled.
After confi
g
uration, these pins are user-pro
g
rammabl e I/O pin s
(
see Note
)
.
RD/
MPI_STRB I
I
I/O
RD is used in the as
y
nchronous peripheral confi
g
uration mode. A low on RD chan
g
es D7 into
a status output. As a status indication, a hi
g
h indicates read
y
, and a low indicates bus
y
. WR
and RD should not be used simultaneousl
y
. If the
y
are, the write strobe overrides.
This pin is also used as the microprocessor interface
(
MPI
)
data transfer strobe. For
PowerPC
, it is the transfer start
(
TS
)
. For
i960
, it is the address/data strobe
(
ADS
)
.
After confi
g
uration, if the MPI is not used, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
WR I
I/O
WR is used in the as
y
nchronous peripheral confi
g
uration mode. When the FPGA is selected,
a low on the write strobe, WR, loads the data on D
[
7:0
]
inputs into an internal data buffer. WR
and RD should not be used simultaneousl
y
. If the
y
are, the write strobe overrides.
After confi
g
uration, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
A
[
17:0
]
O
I/O
Durin
g
master parallel confi
g
uration mode, A
[
17:0
]
address the confi
g
uration EPROM. In
microp rocess or inte rface
(
MPI
)
mode, man
y
of the A
[
n
]
pins have alternate uses as described
below. See the Special Function Blocks section for more MPI information. Durin
g
confi
g
ura-
tion, if not in master parallel or an MPI confi
g
uration mode, these pins are 3-stated with a pull-
up enabled.
After confi
g
uration, the pins are user-pro
g
rammable I/O pins
(
see Note
)
.
Pin Inform ation (continued)
Table 67. Pin Descriptions
(
continued
)
S
y
mbol I/O Descri
p
tion
Note: The FPGA States of Operation section contains more information on how to control these si
g
nals durin
g
start-up. The tim in
g
of DONE
release is controlled b
y
one set of bit stream options, and the timin
g
of the simultaneous release of all other confi
g
uration pins
(
and the
activation of all user I/Os
)
is controlled b
y
a second set of options.
152 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
S
p
ecial-Pur
p
ose Pins
(
continued
)
A11/MPI_IRQ O
I/O MPI active-low interrupt re
q
uest output.
After confi
g
uration, if the MPI is not used, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
A10/MPI_BI O
I/O
PowerPC
mode MPI burst inhibit out put.
After confi
g
uration, if the MPI is not used, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
A9/MPI_ACK O
I/O
In
PowerPC
mode MPI operation, this is the active-hi
g
h transfer acknowled
g
e
(
TA
)
output. For
i960
MPI operation, it is the active-low read
y
/record
(
RDYRCV
)
output.
After confi
g
uration, if the MPI is not used, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
A8/MPI_RW I
I/O
In
PowerPC
mode MPI operation, this is the active-low write/active-hi
g
h read control si
g
nals.
For
i960
operation, it is the active-hi
g
h write/active-low read control si
g
nal.
After confi
g
uration, if the MPI is not used, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
A7/MPI_CLK I
I/O
This is the clock used for the s
y
nchronous MPI interface. For
PowerPC
, it is the CLKOUT
si
g
nal. For
i960
, it is the s
y
stem clock that is chosen for the
i960
external bus interface.
After confi
g
uration, if the MPI is not used, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
A
[
4:0
]
I
I/O
For
PowerPC
operation, these are the
PowerPC
address inputs. The address bit mappin
g
(
in
PowerPC
/FPG A nota tio n
)
is A
[
31
]
/A
[
0
]
, A
[
30
]
/A
[
1
]
, A
[
29
]
/A
[
2
]
, A
[
28
]
/A
[
3
]
, A
[
27
]
/A
[
4
]
. Note
that A
[
27
]
/A
[
4
]
is the MSB of the address. The A
[
4:2
]
inputs are not used in
i960
MPI
mode.
After confi
g
uration, if the MPI is not used, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
A
[
1:0
]
/
MPI_BE[1:0] I
I/O
For
i960
operation, MPI_BE[1:0] provide the
i960
b
y
te enable si
g
nals, BE[1:0], that are used as
address bits A
[
1:0
]
in
i960
b
y
te-wide operation.
After confi
g
uration, if the MPI is not used, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
D
[
7:0
]
I
I/O
Durin
g
master parallel, peripheral, and slave parallel confi
g
uration modes, D
[
7:0
]
receive
confi
g
uration data, and each pin has a pull-up enabled. Durin
g
serial confi
g
urat ion modes , D0
is the DIN input. D
[
7:0
]
are also the data pins for
PowerPC
microproc ess or mode and the
address/data pins for
i960
microprocessor mode.
After confi
g
uration, the pins are user-pro
g
rammable I/O pins
(
see Note
)
.
DIN I
I/O
Durin
g
slave serial or master serial confi
g
uration modes, DIN accepts serial confi
g
uration
data s
y
nchronous with CCLK. Durin
g
parallel confi
g
uration modes, DIN is the D0 input. Dur-
in
g
confi
g
uration, a pull-up is enabled.
After confi
g
uration, this pin is a user-pro
g
rammable I/O pin
(
see Note
)
.
DOUT O
I/O
Durin
g
confi
g
uration, DOUT is the serial data output that can drive the DIN of dais
y
-chained
slave LCA devices. Data out on DOUT chan
g
es on the fallin
g
ed
g
e of CCLK.
After confi
g
uration, DOUT is a user-pro
g
rammable I/O pin
(
see Note
)
.
Pin Information (continued)
Table 67. Pin Descriptions
(
continued
)
S
y
mbol I/O Descri
p
tion
Note: The FPGA States of Operation section contains more information on how to control these si
g
nals durin
g
start-up. The timin
g
of DONE
release is controlled b
y
one set of bit stream options, and the timin
g
of the simultaneous release of all other confi
g
uration pins
(
and the
activation of all user I/Os
)
is controlled b
y
a second set of options.
Lucent Technologies Inc. 153
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Pin Inform ation (continued)
Package Compatibility
Table 68 provides the number of user I/Os availab le for the
ORCA
Series 3 FPGAs for each available package.
Each package has six dedicated configuration pins.
Tables 70—75 provide the pack age pin and pin function for the
ORCA
Series 3 FPGAs and packages. The bond
pad name is identified in the PIC nomenclature used in the
ORCA
Foundry design editor.
When the number of FPGA bond pads exceeds the number of package pins, bond pads are unused. When the
number of package pins exceeds the number of bond pads, package pins are left unconnected (no connects).
When a package pin is to be left as a no connect f or a specific die, it is indicated as a note in the de vice pad column
for the FPGA. The tables provide no information on unused pads.
Table 68.
ORCA
I/Os Summary
*User I/O count includes four ExpressCLK inputs.
Device 208-Pi n
SQFP/SQPF2 240-Pin
SQFP/SQFP2 256-Pin
PBGA 352-Pi n
PBGA 432-Pin
EBGA 600-Pin
EBGA
OR3T20
User I/Os* 171 192 192 192 — —
VDD/VSS 31 40 26 48 — —
Confi
g
uration 6 6 6 6 — —
Unused 0 2 32 106 — —
OR3T30
User I/Os* 171 192 221 224 — —
VDD/VSS 31 40 26 48 — —
Confi
g
uration 6 6 6 6 — —
Unused 0 2 3 74 — —
OR3C/T55
User I/Os* 171 192 223 288 — —
VDD/VSS 31 42 26 48 — —
Confi
g
uration 6 6 6 6 — —
Unused 0 0 1 10 — —
OR3C/T80
User I/Os* 171 192 — 298 342 —
VDD/VSS 31 42 — 48 84 —
Confi
g
uration 6 6 — 6 6 —
Unused 0 0 — 0 0 —
OR3T125
User I/Os* 171 192 — 298 342 448
VDD/VSS 31 42 — 48 84 140
Confi
g
uration 6 6 — 6 6 6
Unused 0 0 — 0 0 6
154 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Pin Information
(
continued
)
Compatibility with OR2C/TxxA Series
The pinouts shown f or the OR3Cxx and OR3Txxx devices are consistent with the OR2C/TxxA Series f or all de vices
offered in the same packages. This includes the following pins: VDD, VSS, VDD5 (OR2TxxA Series only), and all
configuration pins.
The following restrictions apply:
1. There are two confi
g
uration modes supported in the OR2C/TxxA Series that are not supported in Series 3: mas-
ter parallel down and s
y
nchronous peripheral modes. The Series 3 FPGAs have two new microprocessor inter-
face
(
MPI
)
confi
g
uration modes that are unavailable in the OR2C/TxxA Series.
2. There are four pins—one per each device side—that are user I/O in the OR2C/TxxA Series which can onl
y
be
used as fast dedicated clocks or
g
lobal inputs in Series 3. These pins are also used to drive the ExpressCLK to
the I/ O FFs on th eir
g
iven side of the device. These four middle ExpressCLK pins should not be used to connect
to a pro
g
rammable clock mana
g
er
(
PCM
)
. A corner ExpressCLK input should be used instead
(
see item 3
below
)
. See Table 69 for a list of these pins in each packa
g
e.
3. There are two other pins that are user I/O in both the OR2C/TxxA and Series 3 but also have optional added
functionalit
y
. Each of these pins drives the ExpressCLKs on two sides of the device. The
y
also have fast connec-
tivit
y
to the pro
g
rammable clock mana
g
er
(
PCM
)
. See Table 69 for a list of these pins in each packa
g
e.
Table 69. Series 3 Ex
p
ressCLK Pin s
Pin Name/
Packa
g
e208-Pin
SQFP/SQFP2 240-Pin
SQFP/SQFP2 256-Pin
PBGA 352-Pin
PBGA 432-Pin
EBGA 600-Pin
EBGA
I-ECKL 22 26 K3 N2 R29 U33
I-ECKB 80 91 W11 AE14 AH16 AM18
I-ECKR 131 152 K18 N23 T2 V2
I-ECKT 178 207 B11 B14 C15 C17
I/O-SECKLL 49 56 W1 AB4 AG29 AK34
I/O-SECKUR 159 184 A19 A25 D5 D5
Lucent Technologies Inc. 155
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Pin Inform ation (continued)
Table 70. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 208-Pin SQFP/SQFP2 Pinout
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
1VSS VSS VSS VSS VSS VSS
2VSS VSS VSS VSS VSS VSS
3 PL1D PL1D PL1D PL1D PL1D I/O
4 PL1A PL2D PL2D PL2D PL2D I/O-A0/MPI_BE0
5 PL2D PL4D PL3D PL4D PL4D I/O
6 PL2C PL5D PL3A PL4A PL5D I/O
7 PL2A PL7D PL4A PL5A PL7D I/O-A1/MPI_BE1
8 PL3D PL8A PL5A PL6A PL8A I/O-A2
9 PL3C PL9D PL6D PL7D PL9D I/O
10 PL3B PL9B PL6B PL7B PL9B I/O
11 PL3A PL9A PL6A PL7A PL9A I/O-A3
12 VDD VDD VDD VDD VDD VDD
13 PL4D PL10D PL7D PL8D PL10D I/O
14 PL4C PL10A PL7C PL8A PL10A I/O
15 PL4B PL11D PL7B PL9D PL11D I/O
16 PL4A PL11A PL7A PL9B PL11A I/O-A4
17 PL5D PL12D PL8D PL9A PL12D I/O-A5
18 PL5C PL12A PL8C PL10C PL12A I/O
19 PL5B PL13D PL8B PL10B PL13D I/O
20 PL5A PL13A PL8A PL10A PL13A I/O-A6
21 VSS VSS VSS VSS VSS VSS
22 PECKL PECKL PECKL PECKL PECKL I-ECKL
23 PL6C PL14C PL9C PL11C PL14C I/O
24 PL6B PL14B PL9B PL11B PL14B I/O
25 PL6A PL14A PL9A PL11A PL14A I/O-A7/MPI_CLK
26 VDD VDD VDD VDD VDD VDD
27 PL7D PL15D PL10D PL12D PL15D I/O
28 PL7C PL15C PL10C PL12C PL15C I/O
29 PL7B PL15B PL10B PL12B PL15B I/O
30 PL7A PL15A PL10A PL12A PL15A I/O-A8/MPI_RW
31 VSS VSS VSS VSS VSS VSS
32 PL8D PL16D PL11D PL13D PL16D I/O-A9/MPI_ACK
33 PL8C PL16A PL11C PL13B PL16A I/O
34 PL8B PL17D PL11B PL13A PL17D I/O
35 PL8A PL17A PL11A PL14C PL17A I/O-A10/MPI_BI
36 PL9D PL18D PL12D PL14B PL18D I/O
37 PL9C PL18A PL12C PL15C PL18A I/O
38 PL9B PL19D PL12B PL15B PL19D I/O
39 PL9A PL19A PL12A PL15A PL19A I/O-A11/MPI_IRQ
Pin Inform ation (continued)
Table 70. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 208-Pin SQFP/SQFP2 Pinout
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
1VSS VSS VSS VSS VSS VSS
2VSS VSS VSS VSS VSS VSS
3 PL1D PL1D PL1D PL1D PL1D I/O
4 PL1A PL2D PL2D PL2D PL2D I/O-A0/MPI_BE0
5 PL2D PL4D PL3D PL4D PL4D I/O
6 PL2C PL5D PL3A PL4A PL5D I/O
7 PL2A PL7D PL4A PL5A PL7D I/O-A1/MPI_BE1
8 PL3D PL8A PL5A PL6A PL8A I/O-A2
9 PL3C PL9D PL6D PL7D PL9D I/O
10 PL3B PL9B PL6B PL7B PL9B I/O
11 PL3A PL9A PL6A PL7A PL9A I/O-A3
12 VDD VDD VDD VDD VDD VDD
13 PL4D PL10D PL7D PL8D PL10D I/O
14 PL4C PL10A PL7C PL8A PL10A I/O
15 PL4B PL11D PL7B PL9D PL11D I/O
16 PL4A PL11A PL7A PL9B PL11A I/O-A4
17 PL5D PL12D PL8D PL9A PL12D I/O-A5
18 PL5C PL12A PL8C PL10C PL12A I/O
19 PL5B PL13D PL8B PL10B PL13D I/O
20 PL5A PL13A PL8A PL10A PL13A I/O-A6
21 VSS VSS VSS VSS VSS VSS
22 PECKL PECKL PECKL PECKL PECKL I-ECKL
23 PL6C PL14C PL9C PL11C PL14C I/O
24 PL6B PL14B PL9B PL11B PL14B I/O
25 PL6A PL14A PL9A PL11A PL14A I/O-A7/MPI_CLK
26 VDD VDD VDD VDD VDD VDD
27 PL7D PL15D PL10D PL12D PL15D I/O
28 PL7C PL15C PL10C PL12C PL15C I/O
29 PL7B PL15B PL10B PL12B PL15B I/O
30 PL7A PL15A PL10A PL12A PL15A I/O-A8/MPI_RW
31 VSS VSS VSS VSS VSS VSS
32 PL8D PL16D PL11D PL13D PL16D I/O-A9/MPI_ACK
33 PL8C PL16A PL11C PL13B PL16A I/O
34 PL8B PL17D PL11B PL13A PL17D I/O
35 PL8A PL17A PL11A PL14C PL17A I/O-A10/MPI_BI
36 PL9D PL18D PL12D PL14B PL18D I/O
37 PL9C PL18A PL12C PL15C PL18A I/O
38 PL9B PL19D PL12B PL15B PL19D I/O
39 PL9A PL19A PL12A PL15A PL19A I/O-A11/MPI_IRQ
156 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
40 VDD VDD VDD VDD VDD VDD
41 PL10D PL20D PL13D PL16D PL20D I/O-A12
42 PL10C PL20B PL13B PL16B PL20B I/O
43 PL10B PL21D PL14D PL17D PL21D I/O
44 PL10A PL21B PL14B PL17B PL21B I/O-A13
45 PL11D PL22D PL15D PL18D PL22D I/O
46 PL11A PL24A PL16D PL19D PL24A I/O-A14
47 PL12D PL26D PL17D PL20D PL26D I/O
48 PL12C PL27D PL17A PL21D PL27D I/O
49 PL12B PL27A PL18C PL21A PL27A I/O-SECKLL
50 PL12A PL28A PL18A PL22A PL28A I/O-A15
51 VSS VSS VSS VSS VSS VSS
52 PCCLK PCCLK PCCLK PCCLK PCCLK CCLK
53 VSS VSS VSS VSS VSS VSS
54 VSS VSS VSS VSS VSS VSS
55 PB1A PB1A PB1A PB1A PB1A I/O-A16
56 PB1B PB2A PB1D PB2A PB2A I/O
57 PB1C PB2D PB2A PB2D PB2D I/O
58 PB1D PB3D PB2D PB3D PB3D I/O
59 PB2A PB4D PB3D PB4D PB4D I/O-A17
60 PB2D PB5D PB4D PB5D PB5D I/O
61 PB3A PB6D PB5B PB6B PB6D I/O
62 PB3B PB7D PB5D PB6D PB7D I/O
63 PB3C PB8D PB6B PB7B PB8D I/O
64 PB3D PB9D PB6D PB7D PB9D I/O
65 VDD VDD VDD VDD VDD VDD
66 PB4A PB10A PB7A PB8A PB10A I/O
67 PB4B PB10D PB7B PB8D PB10D I/O
68 PB4C PB11A PB7C PB9A PB11A I/O
69 PB4D PB11D PB7D PB9C PB11D I/O
70 PB5A PB12A PB8A PB9D PB12A I/O
71 PB5B PB12D PB8B PB10A PB12D I/O
72 PB5C PB13A PB8C PB10B PB13A I/O
73 PB5D PB13D PB8D PB10D PB13D I/O
74 VSS VSS VSS VSS VSS VSS
75 PB6A PB14A PB9A PB11A PB14A I/O
76 PB6B PB14B PB9B PB11B PB14B I/O
77 PB6C PB14C PB9C PB11C PB14C I/O
78 PB6D PB14D PB9D PB11D PB14D I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 70. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125, 208-Pin SQFP/SQFP2 Pinout (continued)
Lucent Technologies Inc. 157
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
79 VSS VSS VSS VSS VSS VSS
80 PECKB PECKB PECKB PECKB PECKB I-ECKB
81 PB7B PB15B PB10B PB12B PB15B I/O
82 PB7C PB15C PB10C PB12C PB15C I/O
83 PB7D PB15D PB10D PB12D PB15D I/O
84 VSS VSS VSS VSS VSS VSS
85 PB8A PB16A PB11A PB13A PB16A I/O
86 PB8B PB16D PB11B PB13B PB16D I/O
87 PB8C PB17A PB11C PB13C PB17A I/O
88 PB8D PB17D PB11D PB14A PB17D I/O
89 PB9A PB18A PB12A PB14B PB18A I/O-HDC
90 PB9B PB18D PB12B PB14D PB18D I/O
91 PB9C PB19A PB12C PB15A PB19A I/O
92 PB9D PB19D PB12D PB15D PB19D I/O
93 VDD VDD VDD VDD VDD VDD
94 PB10A PB20A PB13A PB16A PB20A I/O-LDC
95 PB10B PB21D PB13D PB16D PB21D I/O
96 PB10C PB22A PB14A PB17A PB22A I/O
97 PB10D PB23D PB14D PB17D PB23D I/O
98 PB11A PB24A PB15A PB18A PB24A I/O-INIT
99 PB11C PB25A PB16A PB19A PB25A I/O
100 PB11D PB26A PB17A PB20A PB26A I/O
101 PB12A PB27D PB18A PB21D PB27D I/O
102 PB12D PB28D PB18D PB22D PB28D I/O
103 VSS VSS VSS VSS VSS VSS
104 PDONE PDONE PDONE PDONE PDONE DONE
105 VSS VSS VSS VSS VSS VSS
106 PRESETN PRESETN PRESETN PRESETN PRESETN RESET
107 PPRGMN PPRGMN PPRGMN PPRGMN PPRGMN PRGM
108 PR12A PR28A PR18A PR22A PR28A I/O-M0
109 PR12D PR27A PR18D PR21A PR27A I/O
110 PR11A PR26A PR17B PR20A PR26A I/O
111 PR11B PR25A PR16A PR19A PR25A I/O
112 PR10A PR22D PR15D PR18D PR22D I/O-M1
113 PR10B PR21A PR14A PR17A PR21A I/O
114 PR10C PR21D PR14D PR17D PR21D I/O
115 PR10D PR20A PR13A PR16A PR20A I/O
116 VDD VDD VDD VDD VDD VDD
117 PR9A PR19A PR12A PR15A PR19A I/O-M2
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 70. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 208-Pin SQFP/SQFP2 Pinout (continued)
158 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
118 PR9B PR19D PR12B PR15D PR19D I/O
119 PR9C PR18A PR12C PR14A PR18A I/O
120 PR9D PR18D PR12D PR14C PR18D I/O
121 PR8A PR17A PR11A PR14D PR17A I/O-M3
122 PR8B PR17D PR11B PR13A PR17D I/O
123 PR8C PR16A PR11C PR13B PR16A I/O
124 PR8D PR16D PR11D PR13D PR16D I/O
125 VSS VSS VSS VSS VSS VSS
126 PR7A PR15A PR10A PR12A PR15A I/O
127 PR7B PR15B PR10B PR12B PR15B I/O
128 PR7C PR15C PR10C PR12C PR15C I/O
129 PR7D PR15D PR10D PR12D PR15D I/O
130 VDD VDD VDD VDD VDD VDD
131 PECKR PECKR PECKR PECKR PECKR I-ECKR
132 PR6B PR14B PR9B PR11B PR14B I/O
133 PR6C PR14C PR9C PR11C PR14C I/O
134 PR6D PR14D PR9D PR11D PR14D I/O
135 VSS VSS VSS VSS VSS VSS
136 PR5A PR13A PR8A PR10A PR13A I/O
137 PR5B PR13D PR8B PR10C PR13D I/O
138 PR5C PR12A PR8C PR10D PR12A I/O
139 PR5D PR12D PR8D PR9B PR12D I/O
140 PR4A PR11A PR7A PR9C PR11A I/O-CS1
141 PR4B PR11D PR7B PR9D PR11D I/O
142 PR4C PR10A PR7C PR8A PR10A I/O
143 PR4D PR10D PR7D PR8D PR10D I/O
144 VDD VDD VDD VDD VDD VDD
145 PR3A PR9A PR6A PR7A PR9A I/O-CS0
146 PR3B PR9B PR6B PR7B PR9B I/O
147 PR3C PR8B PR5B PR6B PR8B I/O
148 PR3D PR8D PR5D PR6D PR8D I/O
149 PR2A PR7A PR4A PR5A PR7A I/O-RD/MPI_STRB
150 PR2C PR5A PR4D PR5D PR5A I/O
151 PR2D PR4A PR3A PR4A PR4A I/O
152 PR1A PR3A PR2A PR3A PR3A I/O-WR
153 PR1C PR2A PR2C PR2A PR2A I/O
154 PR1D PR1A PR1A PR1A PR1A I/O
155 VSS VSS VSS VSS VSS VSS
156 PRD_CFGN PRD_CFGN PRD_CFGN PRD_CFGN PRD_CFGN RD_CFG
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 70. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 208-Pin SQFP/SQFP2 Pinout (continued)
Lucent Technologies Inc. 159
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
157 VSS VSS VSS VSS VSS VSS
158 VSS VSS VSS VSS VSS VSS
159 PT12D PT28D PT18D PT22D PT28D I/O-SECKUR
160 PT12A PT27A PT17D PT21A PT27A I/O-RDY/RCLK/MPI_ALE
161 PT11D PT25D PT16D PT19D PT25D I/O
162 PT11C PT25A PT16A PT19A PT25A I/O
163 PT11A PT24D PT15D PT18D PT24D I/O-D7
164 PT10D PT23D PT14D PT17D PT23D I/O
165 PT10C PT22D PT14A PT17A PT22D I/O
166 PT10B PT21D PT13D PT16D PT21D I/O
167 PT10A PT20D PT13B PT16B PT20D I/O-D6
168 VDD VDD VDD VDD VDD VDD
169 PT9D PT19D PT12D PT15D PT19D I/O
170 PT9C PT19A PT12C PT15B PT19A I/O
171 PT9B PT18D PT12B PT15A PT18D I/O
172 PT9A PT18A PT12A PT14C PT18A I/O-D5
173 PT8D PT17D PT11D PT14B PT17D I/O
174 PT8C PT17A PT11C PT13D PT17A I/O
175 PT8B PT16D PT11B PT13C PT16D I/O
176 PT8A PT16A PT11A PT13A PT16A I/O-D4
177 VSS VSS VSS VSS VSS VSS
178 PECKT PECKT PECKT PECKT PECKT I-ECKT
179 PT7C PT15C PT10C PT12C PT15C I/O
180 PT7B PT15B PT10B PT12B PT15B I/O
181 PT7A PT15A PT10A PT12A PT15A I/O-D3
182 VSS VSS VSS VSS VSS VSS
183 PT6D PT14D PT9D PT11D PT14D I/O
184 PT6C PT14C PT9C PT11C PT14C I/O
185 PT6B PT14B PT9B PT11B PT14B I/O
186 PT6A PT14A PT9A PT11A PT14A I/O-D2
187 VSS VSS VSS VSS VSS VSS
188 PT5D PT13D PT8D PT10D PT13D I/O-D1
189 PT5C PT13A PT8C PT10B PT13A I/O
190 PT5B PT12D PT8B PT10A PT12D I/O
191 PT5A PT12A PT8A PT9C PT12A I/O-D0/DIN
192 PT4D PT11D PT7D PT9B PT11D I/O
193 PT4C PT11A PT7C PT8D PT11A I/O
194 PT4B PT10D PT7B PT8C PT10D I/O
195 PT4A PT10A PT7A PT8A PT10A I/O-DOUT
196 VDD VDD VDD VDD VDD VDD
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 70. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 208-Pin SQFP/SQFP2 Pinout (continued)
160 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
197 PT3D PT9D PT6D PT7D PT9D I/O
198 PT3C PT8A PT6A PT7A PT8A I/O
199 PT3B PT7A PT5C PT6C PT7A I/O
200 PT3A PT6A PT5A PT6A PT6A I/O-TDI
201 PT2D PT5A PT4A PT5A PT5A I/O
202 PT2A PT4A PT3A PT4A PT4A I/O-TMS
203 PT1D PT3A PT2C PT3A PT3A I/O
204 PT1C PT2A PT2A PT2A PT2A I/O
205 PT1B PT1D PT1D PT1D PT1D I/O
206 PT1A PT1A PT1A PT1A PT1A I/O-TCK
207 VSS VSS VSS VSS VSS VSS
208 PRD_DATA PRD_DATA PRD_DATA PRD_DATA PRD_DATA RD_DATA/TDO
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 70. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 208-Pin SQFP/SQFP2 Pinout (continued)
Lucent Technologies Inc. 161
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Pin Inform ation
(
continued
)
Table 71. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 240-Pin SQFP/SQFP2 Pinout
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
1VSS VSS VSS VSS VSS VSS
2VDD VDD VDD VDD VDD VDD
3 PL1D PL1D PL1D PL1D PL1D I/O
4 PL1C PL1B PL1C PL1C PL1C I/O
5PL1BPL1APL1BPL1BPL1B I/O
6 PL1A PL2D PL2D PL2D PL2D I/O-A0/MPI_BE0
7V
SS VSS VSS VSS VSS VSS
8 PL2D PL3D PL3D PL4D PL4D I/O
9 PL2C PL3C PL3A PL4A PL5D I/O
10 PL2B PL3B PL4D PL5D PL6D I/O
11 PL2A PL3A PL4A PL5A PL7D I/O-A1/MPI_BE1
12 PL3D PL4D PL5A PL6A PL8A I/O-A2
13 PL3C PL4C PL6D PL7D PL9D I/O
14 PL3B PL4B PL6B PL7B PL9B I/O
15 PL3A PL4A PL6A PL7A PL9A I/O-A3
16 VDD VDD VDD VDD VDD VDD
17 PL4D PL5D PL7D PL8D PL10D I/O
18 PL4C PL5C PL7C PL8A PL10A I/O
19 PL4B PL5B PL7B PL9D PL11D I/O
20 PL4A PL5A PL7A PL9B PL11A I/O-A4
21 PL5D PL6D PL8D PL9A PL12D I/O-A5
22 PL5C PL6C PL8C PL10C PL12A I/O
23 PL5B PL6B PL8B PL10B PL13D I/O
24 PL5A PL6A PL8A PL10A PL13A I/O-A6
25 VSS VSS VSS VSS VSS VSS
26 PECKL PECKL PECKL PECKL PECKL I-ECKL
27 PL6C PL7C PL9C PL11C PL14C I/O
28 PL6B PL7B PL9B PL11B PL14B I/O
29 PL6A PL7A PL9A PL11A PL14A I/O-A7/MPI_CLK
30 VDD VDD VDD VDD VDD VDD
31 PL7D PL8D PL10D PL12D PL15D I/O
32 PL7C PL8C PL10C PL12C PL15C I/O
33 PL7B PL8B PL10B PL12B PL15B I/O
34 PL7A PL8A PL10A PL12A PL15A I/O-A8/MPI_RW
35 VSS VSS VSS VSS VSS VSS
36 PL8D PL9D PL11D PL13D PL16D I/O-A9/MPI_ACK
37 PL8C PL9C PL11C PL13B PL16A I/O
38 PL8B PL9B PL11B PL13A PL17D I/O
39 PL8A PL9A PL11A PL14C PL17A I/O-A10/MPI_BI
162 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
40 PL9D PL10D PL12D PL14B PL18D I/O
41 PL9C PL10C PL12C PL15C PL18A I/O
42 PL9B PL10B PL12B PL15B PL19D I/O
43 PL9A PL10A PL12A PL15A PL19A I/O-A11/MPI_IRQ
44 VDD VDD VDD VDD VDD VDD
45 PL10D PL11D PL13D PL16D PL20D I/O-A12
46 PL10C PL11C PL13B PL16B PL20B I/O
47 PL10B PL11B PL14D PL17D PL21D I/O
48 PL10A PL11A PL14B PL17B PL21B I/O-A13
49 PL11D PL12D PL14A PL17A PL21A I/O
50 PL11C PL12C PL15D PL18D PL22D I/O
51 PL11B PL12B PL15B PL18B PL23D I/O
52 PL11A PL12A PL16D PL19D PL24A I/O-A14
53 VSS VSS VSS VSS VSS VSS
54 PL12D PL13D PL17D PL20D PL26D I/O
55 PL12C PL13A PL17A PL21D PL27D I/O
56 PL12B PL14C PL18C PL21A PL27A I/O-SECKLL
57 PL12A PL14A PL18A PL22A PL28A I/O-A15
58 VSS VSS VSS VSS VSS VSS
59 PCCLK PCCLK PCCLK PCCLK PCCLK CCLK
60 VDD VDD VDD VDD VDD VDD
61 VSS VSS VSS VSS VSS VSS
62 VSS VSS VSS VSS VSS VSS
63 PB1A PB1A PB1A PB1A PB1A I/O-A16
64 PB1B PB1D PB1D PB2A PB2A I/O
65 PB1C PB2A PB2A PB2D PB2D I/O
66 PB1D PB2D PB2D PB3D PB3D I/O
67 VSS VSS VSS VSS VSS VSS
68 PB2A PB3A PB3D PB4D PB4D I/O-A17
69 PB2B PB3B PB4D PB5D PB5D I/O
70 PB2C PB3C PB5A PB6A PB6A I/O
71 PB2D PB3D PB5B PB6B PB6D I/O
72 PB3A PB4A PB5D PB6D PB7D I/O
73 PB3B PB4B PB6A PB7A PB8A I/O
74 PB3C PB4C PB6B PB7B PB8D I/O
75 PB3D PB4D PB6D PB7D PB9D I/O
76 VDD VDD VDD VDD VDD VDD
77 PB4A PB5A PB7A PB8A PB10A I/O
78 PB4B PB5B PB7B PB8D PB10D I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 71. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 240-Pin SQFP/SQFP2 Pinout (continued)
Lucent Technologies Inc. 163
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
79 PB4C PB5C PB7C PB9A PB11A I/O
80 PB4D PB5D PB7D PB9C PB11D I/O
81 PB5A PB6A PB8A PB9D PB12A I/O
82 PB5B PB6B PB8B PB10A PB12D I/O
83 PB5C PB6C PB8C PB10B PB13A I/O
84 PB5D PB6D PB8D PB10D PB13D I/O
85 VSS VSS VSS VSS VSS VSS
86 PB6A PB7A PB9A PB11A PB14A I/O
87 PB6B PB7B PB9B PB11B PB14B I/O
88 PB6C PB7C PB9C PB11C PB14C I/O
89 PB6D PB7D PB9D PB11D PB14D I/O
90 VSS VSS VSS VSS VSS VSS
91 PECKB PECKB PECKB PECKB PECKB I-ECKB
92 PB7B PB8B PB10B PB12B PB15B I/O
93 PB7C PB8C PB10C PB12C PB15C I/O
94 PB7D PB8D PB10D PB12D PB15D I/O
95 VSS VSS VSS VSS VSS VSS
96 PB8A PB9A PB11A PB13A PB16A I/O
97 PB8B PB9B PB11B PB13B PB16D I/O
98 PB8C PB9C PB11C PB13C PB17A I/O
99 PB8D PB9D PB11D PB14A PB17D I/O
100 PB9A PB10A PB12A PB14B PB18A I/O-HDC
101 PB9B PB10B PB12B PB14D PB18D I/O
102 PB9C PB10C PB12C PB15A PB19A I/O
103 PB9D PB10D PB12D PB15D PB19D I/O
104 VDD VDD VDD VDD VDD VDD
105 PB10A PB11A PB13A PB16A PB20A I/O-LDC
106 PB10B PB11D PB13D PB16D PB21D I/O
107 PB10C PB12A PB14A PB17A PB22A I/O
108 PB10D PB12B PB14D PB17D PB23D I/O
109 PB11A PB12C PB15A PB18A PB24A I/O-INIT
110 PB11B PB12D PB15D PB18D PB24D I/O
111 PB11C PB13A PB16A PB19A PB25A I/O
112 PB11D PB13B PB16D PB19D PB25D I/O
113 VSS —V
SS VSS VSS VSS
114 PB12A PB13D PB17A PB20A PB26A I/O
115 PB12B PB14A PB17D PB21A PB27A I/O
116 PB12C PB14B PB18A PB21D PB27D I/O
117 PB12D PB14D PB18D PB22D PB28D I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 71. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 240-Pin SQFP/SQFP2 Pinout (continued)
164 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
118 VSS VSS VSS VSS VSS VSS
119 PDONE PDONE PDONE PDONE PDONE DONE
120 VDD VDD VDD VDD VDD VDD
121 VSS VSS VSS VSS VSS VSS
122 PRESETN PRESETN PRESETN PRESETN PRESETN RESET
123 PPRGMN PPRGMN PPRGMN PPRGMN PPRGMN PRGM
124 PR12A PR14A PR18A PR22A PR28A I/O-M0
125 PR12B PR14D PR18C PR22D PR28D I/O
126 PR12C PR13A PR18D PR21A PR27A I/O
127 PR12D PR13D PR17B PR20A PR26A I/O
128 VSS VSS VSS VSS VSS VSS
129 PR11A PR12A PR16A PR19A PR25A I/O
130 PR11B PR12B PR16D PR19D PR24A I/O
131 PR11C PR12C PR15A PR18A PR23A I/O
132 PR11D PR12D PR15C PR18C PR23D I/O
133 PR10A PR11A PR15D PR18D PR22D I/O-M1
134 PR10B PR11B PR14A PR17A PR21A I/O
135 PR10C PR11C PR14D PR17D PR21D I/O
136 PR10D PR11D PR13A PR16A PR20A I/O
137 VDD VDD VDD VDD VDD VDD
138 PR9A PR10A PR12A PR15A PR19A I/O-M2
139 PR9B PR10B PR12B PR15D PR19D I/O
140 PR9C PR10C PR12C PR14A PR18A I/O
141 PR9D PR10D PR12D PR14C PR18D I/O
142 PR8A PR9A PR11A PR14D PR17A I/O-M3
143 PR8B PR9B PR11B PR13A PR17D I/O
144 PR8C PR9C PR11C PR13B PR16A I/O
145 PR8D PR9D PR11D PR13D PR16D I/O
146 VSS VSS VSS VSS VSS VSS
147 PR7A PR8A PR10A PR12A PR15A I/O
148 PR7B PR8B PR10B PR12B PR15B I/O
149 PR7C PR8C PR10C PR12C PR15C I/O
150 PR7D PR8D PR10D PR12D PR15D I/O
151 VDD VDD VDD VDD VDD VDD
152 PECKR PECKR PECKR PECKR PECKR I-ECKR
153 PR6B PR7B PR9B PR11B PR14B I/O
154 PR6C PR7C PR9C PR11C PR14C I/O
155 PR6D PR7D PR9D PR11D PR14D I/O
156 VSS VSS VSS VSS VSS VSS
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 71. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 240-Pin SQFP/SQFP2 Pinout (continued)
Lucent Technologies Inc. 165
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
157 PR5A PR6A PR8A PR10A PR13A I/O
158 PR5B PR6B PR8B PR10C PR13D I/O
159 PR5C PR6C PR8C PR10D PR12A I/O
160 PR5D PR6D PR8D PR9B PR12D I/O
161 PR4A PR5A PR7A PR9C PR11A I/O-CS1
162 PR4B PR5B PR7B PR9D PR11D I/O
163 PR4C PR5C PR7C PR8A PR10A I/O
164 PR4D PR5D PR7D PR8D PR10D I/O
165 VDD VDD VDD VDD VDD VDD
166 PR3A PR4A PR6A PR7A PR9A I/O-CS0
167 PR3B PR4B PR6B PR7B PR9B I/O
168 PR3C PR4C PR5B PR6B PR8B I/O
169 PR3D PR4D PR5D PR6D PR8D I/O
170 PR2A PR3A PR4A PR5A PR7A I/O-RD/MPI_STRB
171 PR2B PR3B PR4B PR5B PR6A I/O
172 PR2C PR3C PR4D PR5D PR5A I/O
173 PR2D PR3D PR3A PR4A PR4A I/O
174 VSS VSS VSS VSS VSS VSS
175 PR1A PR2A PR2A PR3A PR3A I/O-WR
176 PR1B PR2D PR2C PR2A PR2A I/O
177 PR1C PR1A PR1A PR1A PR1A I/O
178 PR1D PR1D PR1D PR1D PR1D I/O
179 VSS VSS VSS VSS VSS VSS
180 PRD_CFGN PRD_CFGN PRD_CFGN PRD_CFGN PRD_CFGN RD_CFG
181 VSS VSS VSS VSS VSS VSS
182 VDD VDD VDD VDD VDD VDD
183 VSS VSS VSS VSS VSS VSS
184 PT12D PT14D PT18D PT22D PT28D I/O-SECKUR
185 PT12C PT14C PT18B PT22A PT28A I/O
186 PT12B PT14A PT18A PT21D PT27D I/O
187 PT12A PT13D PT17D PT21A PT27A I/O-RDY/RCLK/MPI_ALE
188 VSS —V
SS VSS VSS VSS
189 PT11D PT13B PT16D PT19D PT25D I/O
190 PT11C PT13A PT16C PT19C PT25C I/O
191 PT11B PT12D PT16A PT19A PT25A I/O
192 PT11A PT12C PT15D PT18D PT24D I/O-D7
193 PT10D PT12A PT14D PT17D PT23D I/O
194 PT10C PT11D PT14A PT17A PT22D I/O
195 PT10B PT11C PT13D PT16D PT21D I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 71. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 240-Pin SQFP/SQFP2 Pinout (continued)
166 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
196 PT10A PT11B PT13B PT16B PT20D I/O-D6
197 VDD VDD VDD VDD VDD VDD
198 PT9D PT10D PT12D PT15D PT19D I/O
199 PT9C PT10C PT12C PT15B PT19A I/O
200 PT9B PT10B PT12B PT15A PT18D I/O
201 PT9A PT10A PT12A PT14C PT18A I/O-D5
202 PT8D PT9D PT11D PT14B PT17D I/O
203 PT8C PT9C PT11C PT13D PT17A I/O
204 PT8B PT9B PT11B PT13C PT16D I/O
205 PT8A PT9A PT11A PT13A PT16A I/O-D4
206 VSS VSS VSS VSS VSS VSS
207 PECKT PECKT PECKT PECKT PECKT I-ECKT
208 PT7C PT8C PT10C PT12C PT15C I/O
209 PT7B PT8B PT10B PT12B PT15B I/O
210 PT7A PT8A PT10A PT12A PT15A I/O-D3
211 VSS VSS VSS VSS VSS VSS
212 PT6D PT7D PT9D PT11D PT14D I/O
213 PT6C PT7C PT9C PT11C PT14C I/O
214 PT6B PT7B PT9B PT11B PT14B I/O
215 PT6A PT7A PT9A PT11A PT14A I/O-D2
216 VSS VSS VSS VSS VSS VSS
217 PT5D PT6D PT8D PT10D PT13D I/O-D1
218 PT5C PT6C PT8C PT10B PT13A I/O
219 PT5B PT6B PT8B PT10A PT12D I/O
220 PT5A PT6A PT8A PT9C PT12A I/O-D0/DIN
221 PT4D PT5D PT7D PT9B PT11D I/O
222 PT4C PT5C PT7C PT8D PT11A I/O
223 PT4B PT5B PT7B PT8C PT10D I/O
224 PT4A PT5A PT7A PT8A PT10A I/O-DOUT
225 VDD VDD VDD VDD VDD VDD
226 PT3D PT4D PT6D PT7D PT9D I/O
227 PT3C PT4C PT6A PT7A PT8A I/O
228 PT3B PT4B PT5C PT6C PT7A I/O
229 PT3A PT4A PT5A PT6A PT6A I/O-TDI
230 PT2D PT3D PT4D PT5D PT5D I/O
231 PT2C PT3C PT4A PT5A PT5A I/O
232 PT2B PT3B PT3D PT4D PT4D I/O
233 PT2A PT3A PT3A PT4A PT4A I/O-TMS
234 VSS VSS VSS VSS VSS VSS
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 71. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 240-Pin SQFP/SQFP2 Pinout (continued)
Lucent Technologies Inc. 167
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
235 PT1D PT2D PT2C PT3A PT3A I/O
236 PT1C PT2A PT2A PT2A PT2A I/O
237 PT1B PT1D PT1D PT1D PT1D I/O
238 PT1A PT1A PT1A PT1A PT1A I/O-TCK
239 VSS VSS VSS VSS VSS VSS
240 PRD_DATA PRD_DATA PRD_DATA PRD_DATA PRD_DATA RD_DATA/TDO
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 71. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 240-Pin SQFP/SQFP2 Pinout (continued)
168168 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad Function
B1 VDD VDD VDD VDD
C2 PL1D PL1D PL1D I/O
D2 PL1C PL1B PL1C I/O
D3 PL1B PL1A PL1B I/O
E4 PL1A PL2D PL2D I/O-A0/MPI_BE0
C1 — PL2C PL2C I/O
D1 — PL2B PL2B I/O
E3 — PL2A PL2A I/O
E2 PL2D PL3D PL3D I/O
E1 PL2C PL3C PL3A I/O
F3 PL2B PL3B PL4D I/O
G4 PL2A PL3A PL4A I/O-A1/MPI_BE1
F2 — — PL5D I/O
F1 PL3D PL4D PL5A I/O-A2
G3 PL3C PL4C PL6D I/O
G2 PL3B PL4B PL6B I/O
G1 PL3A PL4A PL6A I/O-A3
H3 PL4D PL5D PL7D I/O
H2 PL4C PL5C PL7C I/O
H1 PL4B PL5B PL7B I/O
J4 PL4A PL5A PL7A I/O-A4
J3 PL5D PL6D PL8D I/O-A5
J2 PL5C PL6C PL8C I/O
J1 PL5B PL6B PL8B I/O
K2 PL5A PL6A PL8A I/O-A6
K3 PECKL PECKL PECKL I-ECKL
K1 PL6C PL7C PL9C I/O
L1 PL6B PL7B PL9B I/O
L2 PL6A PL7A PL9A I/O-A7/MPI_CLK
L3 PL7D PL8D PL10D I/O
L4 PL7C PL8C PL10C I/O
M1 PL7B PL8B PL10B I/O
M2 PL7A PL8A PL10A I/O-A8/MPI_RW
M3 PL8D PL9D PL11D I/O-A9/MPI_ACK
M4 PL8C PL9C PL11C I/O
N1 PL8B PL9B PL11B I/O
N2 PL8A PL9A PL11A I/O-A10/MPI_BI
N3 PL9D PL10D PL12D I/O
P1 PL9C PL10C PL12C I/O
P2 PL9B PL10B PL12B I/O
R1 PL9A PL10A PL12A I/O-A11/MPI_IRQ
P3 PL10D PL11D PL13D I/O-A12
R2 PL10C PL11C PL13B I/O
T1 PL10B PL11B PL14D I/O
P4 PL10A PL11A PL14B I/O-A13
R3 PL11D PL12D PL14A I/O
T2 PL11C PL12C PL15D I/O
U1 PL11B PL12B PL15B I/O
T3 PL11A PL12A PL16D I/O-A14
U2 — PL13D PL17D I/O
V1 PL12D PL13C PL17C I/O
T4 PL12C PL13B PL17B I/O
U3 — PL13A PL17A I/O
V2 — PL14D PL18D I/O
W1 PL12B PL14C PL18C I/O-SECKLL
V3 — PL14B PL18B I/O
W2 PL12A PL14A PL18A I/O-A15
Y1 PCCLK PCCLK PCCLK CCLK
W3 — — — NC
Y2 PB1A PB1A PB1A I/O-A16
W4 — PB1C PB1C I/O
V4 PB1B PB1D PB1D I/O
U5 PB1C PB2A PB2A I/O
Y3 PB1D PB2B PB2B I/O
Y4 — PB2C PB2C I/O
V5 — PB2D PB2D I/O
W5 PB2A PB3A PB3D I/O-A17
Y5 PB2B PB3B PB4D I/O
V6 PB2C PB3C PB5A I/O
U7 PB2D PB3D PB5B I/O
W6 PB3A PB4A PB5D I/O
Y6 PB3B PB4B PB6A I/O
V7 PB3C PB4C PB6B I/O
W7 PB3D PB4D PB6D I/O
Y7 PB4A PB5A PB7A I/O
V8 PB4B PB5B PB7B I/O
W8 PB4C PB5C PB7C I/O
Y8 PB4D PB5D PB7D I/O
U9 PB5A PB6A PB8A I/O
V9 PB5B PB6B PB8B I/O
W9 PB5C PB6C PB8C I/O
Y9 PB5D PB6D PB8D I/O
W10 PB6A PB7A PB9A I/O
V10 PB6B PB7B PB9B I/O
Y10 PB6C PB7C PB9C I/O
Y11 PB6D PB7D PB9D I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad Function
Pin Information
(
continued
)
Table 72. OR 3T20, OR3T30, and OR3C/T55 256-Pin PBGA Pinout
Lucent Technologies Inc. 169
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
W11 PECKB PECKB PECKB I-ECKB
V11 PB7B PB8B PB10B I/O
U11 PB7C PB8C PB10C I/O
Y12 PB7D PB8D PB10D I/O
W12 PB8A PB9A PB11A I/O
V12 PB8B PB9B PB11B I/O
U12 PB8C PB9C PB11C I/O
Y13 PB8D PB9D PB11D I/O
W13 PB9A PB10A PB12A I/O-HDC
V13 PB9B PB10B PB12B I/O
Y14 PB9C PB10C PB12C I/O
W14 PB9D PB10D PB12D I/O
Y15 PB10A PB11A PB13A I/O-LDC
V14 PB10B PB11B PB13B I/O
W15 PB10C PB11C PB13C I/O
Y16 PB10D PB11D PB13D I/O
U14 — PB12A PB14A I/O
V15 — PB12B PB14D I/O
W16 PB11A PB12C PB15A I/O-INIT
Y17 — — PB15D I/O
V16 — PB12D PB16A I/O
W17 PB11B PB13A PB16D I/O
Y18 PB11C PB13B PB17A I/O
U16 PB11D PB13C PB17C I/O
V17 PB12A PB13D PB17D I/O
W18 PB12B PB14A PB18A I/O
Y19 PB12C PB14B PB18B I/O
V18 PB12D PB14C PB18C I/O
W19 — PB14D PB18D I/O
Y20 PDONE PDONE PDONE DONE
W20 PRESETN PRESETN PRESETN RESET
V19 PPRGMN PPRGMN PPRGMN PRGM
U19 PR12A PR14A PR18A I/O-M0
U18 — PR14C PR18C I/O
T17 — PR14D PR18D I/O
V20 — PR13A PR17A I/O
U20 PR12B PR13B PR17B I/O
T18 PR12C PR13C PR17C I/O
T19 PR12D PR13D PR17D I/O
T20 PR11A PR12A PR16A I/O
R18 PR11B PR12B PR16D I/O
P17 PR11C PR12C PR15A I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad Function R19 PR11D PR12D PR15C I/O
R20 PR10A PR11A PR15D I/O-M1
P18 PR10B PR11B PR14A I/O
P19 PR10C PR11C PR14D I/O
P20 PR10D PR11D PR13A I/O
N18 PR9A PR10A PR12A I/O-M2
N19 PR9B PR10B PR12B I/O
N20 PR9C PR10C PR12C I/O
M17 PR9D PR10D PR12D I/O
M18 PR8A PR9A PR11A I/O-M3
M19 PR8B PR9B PR11B I/O
M20 PR8C PR9C PR11C I/O
L19 PR8D PR9D PR11D I/O
L18 PR7A PR8A PR10A I/O
L20 PR7B PR8B PR10B I/O
K20 PR7C PR8C PR10C I/O
K19 PR7D PR8D PR10D I/O
K18 PECKR PECKR PECKR I-ECKR
K17 PR6B PR7B PR9B I/O
J20 PR6C PR7C PR9C I/O
J19 PR6D PR7D PR9D I/O
J18 PR5A PR6A PR8A I/O
J17 PR5B PR6B PR8B I/O
H20 PR5C PR6C PR8C I/O
H19 PR5D PR6D PR8D I/O
H18 PR4A PR5A PR7A I/O-CS1
G20 PR4B PR5B PR7B I/O
G19 PR4C PR5C PR7C I/O
F20 PR4D PR5D PR7D I/O
G18 PR3A PR4A PR6A I/O-CS0
F19 PR3B PR4B PR6B I/O
E20 PR3C PR4C PR5B I/O
G17 PR3D PR4D PR5D I/O
F18 PR2A PR3A PR4A I/O-RD/MPI_STRB
E19 PR2B PR3B PR4B I/O
D20 PR2C PR3C PR4D I/O
E18 PR2D PR3D PR3A I/O
D19 PR1A PR2A PR2A I/O-WR
C20 PR1B PR2B PR2B I/O
E17 PR1C PR2C PR2C I/O
D18 PR1D PR2D PR2D I/O
C19 — PR1A PR1A I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad Function
Pin Information
(
continued
)
Table 72. OR3T20, OR3T30, and OR3C/T55 256-Pin PBGA Pinout
(
continued
)
170170 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
B20 — PR1B PR1B I/O
C18 — PR1C PR1C I/O
B19 — PR1D PR1D I/O
A20 PRD_CFGN PRD_CFGN PRD_CFGN RD_CFG
A19 PT12D PT14D PT18D I/O-SECKUR
B18 — PT14C PT18C I/O
B17 PT12C PT14B PT18B I/O
C17 PT12B PT14A PT18A I/O
D16 PT12A PT13D PT17D I/O-RDY/RCLK/MPI_ALE
A18 — PT13C PT17A I/O
A17 PT11D PT13B PT16D I/O
C16 PT11C PT13A PT16C I/O
B16 PT11B PT12D PT16A I/O
A16 PT11A PT12C PT15D I/O-D7
C15 — PT12B PT15A I/O
D14 PT10D PT12A PT14D I/O
B15 PT10C PT11D PT14A I/O
A15 PT10B PT11C PT13D I/O
C14 PT10A PT11B PT13B I/O-D6
B14 PT9D PT11A PT13A I/O
A14 PT9C PT10D PT12D I/O
C13 — PT10C PT12C I/O
B13 PT9B PT10B PT12B I/O
A13 PT9A PT10A PT12A I/O-D5
D12 PT8D PT9D PT11D I/O
C12 PT8C PT9C PT11C I/O
B12 PT8B PT9B PT11B I/O
A12 PT8A PT9A PT11A I/O-D4
B11 PECKT PECKT PECKT I-ECKT
C11 PT7C PT8C PT10C I/O
A11 PT7B PT8B PT10B I/O
A10 PT7A PT8A PT10A I/O-D3
B10 PT6D PT7D PT9D I/O
C10 PT6C PT7C PT9C I/O
D10 PT6B PT7B PT9B I/O
A9 PT6A PT7A PT9A I/O-D2
B9 PT5D PT6D PT8D I/O-D1
C9 PT5C PT6C PT8C I/O
D9 PT5B PT6B PT8B I/O
A8 PT5A PT6A PT8A I/O-D0/DIN
B8 PT4D PT5D PT7D I/O
C8 PT4C PT5C PT7C I/O
A7 PT4B PT5B PT7B I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad Function B7 PT4A PT5A PT7A I/O-DOUT
A6 PT3D PT4D PT6D I/O
C7 PT3C PT4C PT6A I/O
B6 PT3B PT4B PT5C I/O
A5 PT3A PT4A PT5A I/O-TDI
D7 PT2D PT3D PT4D I/O
C6 PT2C PT3C PT4A I/O
B5 PT2B PT3B PT3D I/O
A4 PT2A PT3A PT3A I/O-TMS
C5 — PT2D PT2D I/O
B4 PT1D PT2C PT2C I/O
A3 PT1C PT2B PT2B I/O
D5 PT1B PT2A PT2A I/O
C4 — PT1D PT1D I/O
B3 — PT1C PT1C I/O
B2 — PT1B PT1B I/O
A2 PT1A PT1A PT1A I/O-TCK
C3 PRD_DATA PRD_DATA PRD_DATA RD_DATA/TDO
A1 VSS VSS VSS VSS
D4 VSS VSS VSS VSS
D8 VSS VSS VSS VSS
D13 VSS VSS VSS VSS
D17 VSS VSS VSS VSS
H4 VSS VSS VSS VSS
H17 VSS VSS VSS VSS
N4 VSS VSS VSS VSS
N17 VSS VSS VSS VSS
U4 VSS VSS VSS VSS
U8 VSS VSS VSS VSS
U13 VSS VSS VSS VSS
U17 VSS VSS VSS VSS
J9 VSS VSS VSS VSS*
J10 VSS VSS VSS VSS*
J11 VSS VSS VSS VSS*
J12 VSS VSS VSS VSS*
K9 VSS VSS VSS VSS*
K10 VSS VSS VSS VSS*
K11 VSS VSS VSS VSS*
K12 VSS VSS VSS VSS*
L9 VSS VSS VSS VSS*
L10 VSS VSS VSS VSS*
L11 VSS VSS VSS VSS*
L12 VSS VSS VSS VSS*
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad Function
Pin Information
(
continued
)
Table 72. OR 3T20, OR3T30, and OR3C/T55 256-Pin PBGA Pinout
(
continued
)
Lucent Technologies Inc. 171
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
M9 VSS VSS VSS VSS*
M10 VSS VSS VSS VSS*
M11 VSS VSS VSS VSS*
M12 VSS VSS VSS VSS*
D6 VDD VDD VDD VDD
D11 VDD VDD VDD VDD
D15 VDD VDD VDD VDD
F4 VDD VDD VDD VDD
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad Function F17 VDD VDD VDD VDD
K4 VDD VDD VDD VDD
L17 VDD VDD VDD VDD
R4 VDD VDD VDD VDD
R17 VDD VDD VDD VDD
U6 VDD VDD VDD VDD
U10 VDD VDD VDD VDD
U15 VDD VDD VDD VDD
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad Function
Pin Information
(
continued
)
Table 72. OR3T20, OR3T30, and OR3C/T55 256-Pin PBGA Pinout
(
continued
)
* Thermally enhanced connection.
172 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Pin Information
(
continued
)
Table 73. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 352-Pin PBGA Pinout
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
B1 PL1D PL1D PL1D PL1D PL1D I/O
C2 — PL1C PL1C PL1C PL1C I/O
C1 PL1C PL1B PL1B PL1B PL1B I/O
D2 PL1B PL1A PL1A PL1A PL1A I/O
D3 PL1A PL2D PL2D PL2D PL2D I/O-A0/MPI_BE0
D1 — PL2C PL2C PL2A PL2A I/O
E2 — PL2B PL2B PL3D PL3D I/O
E4 — — — PL3B PL3B I/O
E3 — PL2A PL2A PL3A PL3A I/O
E1 PL2D PL3D PL3D PL4D PL4D I/O
F2 — — PL3C PL4C PL4C I/O
G4 PL2C PL3C PL3B PL4B PL4B I/O
F3 — — PL3A PL4A PL5D I/O
F1 PL2B PL3B PL4D PL5D PL6D I/O
G2 — — PL4C PL5C PL6C I/O
G1 — — PL4B PL5B PL6B I/O
G3 PL2A PL3A PL4A PL5A PL7D I/O-A1/MPI_BE1
H2 — — PL5D PL6D PL8D I/O
J4 — — PL5C PL6C PL8C I/O
H1 — — PL5B PL6B PL8B I/O
H3 PL3D PL4D PL5A PL6A PL8A I/O-A2
J2 — — PL6D PL7D PL9D I/O
J1 PL3C PL4C PL6C PL7C PL9C I/O
K2 PL3B PL4B PL6B PL7B PL9B I/O
J3 PL3A PL4A PL6A PL7A PL9A I/O-A3
K1 PL4D PL5D PL7D PL8D PL10D I/O
K4 PL4C PL5C PL7C PL8A PL10A I/O
L2 PL4B PL5B PL7B PL9D PL11D I/O
K3 PL4A PL5A PL7A PL9B PL11A I/O-A4
L1 PL5D PL6D PL8D PL9A PL12D I/O-A5
M2 PL5C PL6C PL8C PL10C PL12A I/O
M1 PL5B PL6B PL8B PL10B PL13D I/O
L3 PL5A PL6A PL8A PL10A PL13A I/O-A6
N2 PECKL PECKL PECKL PECKL PECKL I-ECKL
M4 PL6C PL7C PL9C PL11C PL14C I/O
N1 PL6B PL7B PL9B PL11B PL14B I/O
M3 PL6A PL7A PL9A PL11A PL14A I/O-A7/MPI_CLK
P2 PL7D PL8D PL10D PL12D PL15D I/O
P4 PL7C PL8C PL10C PL12C PL15C I/O
P1 PL7B PL8B PL10B PL12B PL15B I/O
N3 PL7A PL8A PL10A PL12A PL15A I/O-A8/MPI_RW
R2 PL8D PL9D PL11D PL13D PL16D I/O-A9/MPI_ACK
Lucent Technologies Inc. 173
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
P3 PL8C PL9C PL11C PL13B PL16A I/O
R1 PL8B PL9B PL11B PL13A PL17D I/O
T2 PL8A PL9A PL11A PL14C PL17A I/O-A10/MPI_BI
R3 PL9D PL10D PL12D PL14B PL18D I/O
T1 PL9C PL10C PL12C PL15C PL18A I/O
R4 PL9B PL10B PL12B PL15B PL19D I/O
U2 PL9A PL10A PL12A PL15A PL19A I/O-A11/MPI_IRQ
T3 PL10D PL11D PL13D PL16D PL20D I/O-A12
U1 — — PL13C PL16C PL20C I/O
U4 PL10C PL11C PL13B PL16B PL20B I/O
V2 — — PL13A PL16A PL20A I/O
U3 PL10B PL11B PL14D PL17D PL21D I/O
V1 — — PL14C PL17C PL21C I/O
W2 PL10A PL11A PL14B PL17B PL21B I/O-A13
W1 — — PL14A PL17A PL21A I/O
V3 PL11D PL12D PL15D PL18D PL22D I/O
Y2 PL11C PL12C PL15C PL18C PL22C I/O
W4 PL11B PL12B PL15B PL18B PL23D I/O
Y1 — — PL15A PL18A PL24D I/O
W3 PL11A PL12A PL16D PL19D PL24A I/O-A14
AA2 — — PL16C PL19C PL25C I/O
Y4 — — PL16B PL19B PL25B I/O
AA1 — — PL16A PL19A PL25A I/O
Y3 — PL13D PL17D PL20D PL26D I/O
AB2 PL12D PL13C PL17C PL20C PL26C I/O
AB1 PL12C PL13B PL17B PL20A PL26A I/O
AA3 — PL13A PL17A PL21D PL27D I/O
AC2 — PL14D PL18D PL21C PL27C I/O
AB4 PL12B PL14C PL18C PL21A PL27A I/O-SECKLL
AC1 — PL14B PL18B PL22D PL28D I/O
AB3 — — — PL22C PL28C I/O
AD2 — — — PL22B PL28B I/O
AC3 PL12A PL14A PL18A PL22A PL28A I/O-A15
AD1 PCCLK PCCLK PCCLK PCCLK PCCLK CCLK
AF2 PB1A PB1A PB1A PB1A PB1A I/O-A16
AE3 — — — PB1B PB1B I/O
AF3 — PB1B PB1B PB1C PB1C I/O
AE4 — PB1C PB1C PB1D PB1D I/O
AD4 PB1B PB1D PB1D PB2A PB2A I/O
AF4 PB1C PB2A PB2A PB2D PB2D I/O
AE5 — — PB2B PB3A PB3A I/O
AC5 PB1D PB2B PB2C PB3C PB3C I/O
AD5 — — PB2D PB3D PB3D I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 73. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 352-Pin PBGA Pinout
(
continued
)
174 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
AF5 — PB2C PB3A PB4A PB4A I/O
AE6 — PB2D PB3B PB4B PB4B I/O
AC7 — — PB3C PB4C PB4C I/O
AD6 PB2A PB3A PB3D PB4D PB4D I/O-A17
AF6 — — PB4A PB5A PB5A I/O
AE7 — — PB4B PB5B PB5B I/O
AF7 — — PB4C PB5C PB5C I/O
AD7 — — PB4D PB5D PB5D I/O
AE8 — — PB5A PB6A PB6A I/O
AC9 PB2B PB3B PB5B PB6B PB6D I/O
AF8 PB2C PB3C PB5C PB6C PB7A I/O
AD8 PB2D PB3D PB5D PB6D PB7D I/O
AE9 PB3A PB4A PB6A PB7A PB8A I/O
AF9 PB3B PB4B PB6B PB7B PB8D I/O
AE10 PB3C PB4C PB6C PB7C PB9A I/O
AD9 PB3D PB4D PB6D PB7D PB9D I/O
AF10 PB4A PB5A PB7A PB8A PB10A I/O
AC10 PB4B PB5B PB7B PB8D PB10D I/O
AE11 PB4C PB5C PB7C PB9A PB11A I/O
AD10 PB4D PB5D PB7D PB9C PB11D I/O
AF11 PB5A PB6A PB8A PB9D PB12A I/O
AE12 PB5B PB6B PB8B PB10A PB12D I/O
AF12 PB5C PB6C PB8C PB10B PB13A I/O
AD11 PB5D PB6D PB8D PB10D PB13D I/O
AE13 PB6A PB7A PB9A PB11A PB14A I/O
AC12 PB6B PB7B PB9B PB11B PB14B I/O
AF13 PB6C PB7C PB9C PB11C PB14C I/O
AD12 PB6D PB7D PB9D PB11D PB14D I/O
AE14 PECKB PECKB PECKB PECKB PECKB I-ECKB
AC14 PB7B PB8B PB10B PB12B PB15B I/O
AF14 PB7C PB8C PB10C PB12C PB15C I/O
AD13 PB7D PB8D PB10D PB12D PB15D I/O
AE15 PB8A PB9A PB11A PB13A PB16A I/O
AD14 PB8B PB9B PB11B PB13B PB16D I/O
AF15 PB8C PB9C PB11C PB13C PB17A I/O
AE16 PB8D PB9D PB11D PB14A PB17D I/O
AD15 PB9A PB10A PB12A PB14B PB18A I/O-HDC
AF16 PB9B PB10B PB12B PB14D PB18D I/O
AC15 PB9C PB10C PB12C PB15A PB19A I/O
AE17 PB9D PB10D PB12D PB15D PB19D I/O
AD16 PB10A PB11A PB13A PB16A PB20A I/O-LDC
AF17 — — PB13B PB16B PB20D I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 73. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 352-Pin PBGA Pinout
(
continued
)
Lucent Technologies Inc. 175
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
AC17 PB10B PB11B PB13C PB16C PB21A I/O
AE18 PB10C PB11C PB13D PB16D PB21D I/O
AD17 PB10D PB11D PB14A PB17A PB22A I/O
AF18 — PB12A PB14B PB17B PB23A I/O
AE19 — — PB14C PB17C PB23C I/O
AF19 — PB12B PB14D PB17D PB23D I/O
AD18 PB11A PB12C PB15A PB18A PB24A I/O-INIT
AE20 — — PB15B PB18B PB24B I/O
AC19 — — PB15C PB18C PB24C I/O
AF20 — — PB15D PB18D PB24D I/O
AD19 — PB12D PB16A PB19A PB25A I/O
AE21 — — PB16B PB19B PB25B I/O
AC20 — — PB16C PB19C PB25C I/O
AF21 PB11B PB13A PB16D PB19D PB25D I/O
AD20 PB11C PB13B PB17A PB20A PB26A I/O
AE22 PB11D PB13C PB17B PB20B PB26B I/O
AF22 PB12A PB13D PB17C PB20D PB26D I/O
AD21 PB12B PB14A PB17D PB21A PB27A I/O
AE23 — — — PB21B PB27B I/O
AC22 PB12C PB14B PB18A PB21D PB27D I/O
AF23 PB12D PB14C PB18B PB22A PB28A I/O
AD22 — PB14D PB18C PB22B PB28B I/O
AE24 — — — PB22C PB28C I/O
AD23 — — PB18D PB22D PB28D I/O
AF24 PDONE PDONE PDONE PDONE PDONE DONE
AE26 PRESETN PRESETN PRESETN PRESETN PRESETN RESET
AD25 PPRGMN PPRGMN PPRGMN PPRGMN PPRGMN PRGM
AD26 PR12A PR14A PR18A PR22A PR28A I/O-M0
AC25 — PR14B PR18B PR22C PR28C I/O
AC24 — PR14C PR18C PR22D PR28D I/O
AC26 — PR14D PR18D PR21A PR27A I/O
AB25 — PR13A PR17A PR21D PR27D I/O
AB23 PR12B PR13B PR17B PR20A PR26A I/O
AB24 PR12C PR13C PR17C PR20B PR26B I/O
AB26 PR12D PR13D PR17D PR20D PR26D I/O
AA25 PR11A PR12A PR16A PR19A PR25A I/O
Y23 — — PR16B PR19B PR25B I/O
AA24 PR11B PR12B PR16C PR19C PR25C I/O
AA26 — — PR16D PR19D PR24A I/O
Y25 PR11C PR12C PR15A PR18A PR23A I/O
Y26 — — PR15B PR18B PR23B I/O
Y24 PR11D PR12D PR15C PR18C PR23D I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 73. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 352-Pin PBGA Pinout
(
continued
)
176 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
W25 PR10A PR11A PR15D PR18D PR22D I/O-M1
V23 PR10B PR11B PR14A PR17A PR21A I/O
W26 — — PR14B PR17B PR21B I/O
W24 — — PR14C PR17C PR21C I/O
V25 PR10C PR11C PR14D PR17D PR21D I/O
V26 PR10D PR11D PR13A PR16A PR20A I/O
U25 — — PR13B PR16B PR20B I/O
V24 — — PR13C PR16C PR20C I/O
U26 — — PR13D PR16D PR20D I/O
U23 PR9A PR10A PR12A PR15A PR19A I/O-M2
T25 PR9B PR10B PR12B PR15D PR19D I/O
U24 PR9C PR10C PR12C PR14A PR18A I/O
T26 PR9D PR10D PR12D PR14C PR18D I/O
R25 PR8A PR9A PR11A PR14D PR17A I/O-M3
R26 PR8B PR9B PR11B PR13A PR17D I/O
T24 PR8C PR9C PR11C PR13B PR16A I/O
P25 PR8D PR9D PR11D PR13D PR16D I/O
R23 PR7A PR8A PR10A PR12A PR15A I/O
P26 PR7B PR8B PR10B PR12B PR15B I/O
R24 PR7C PR8C PR10C PR12C PR15C I/O
N25 PR7D PR8D PR10D PR12D PR15D I/O
N23 PECKR PECKR PECKR PECKR PECKR I-ECKR
N26 PR6B PR7B PR9B PR11B PR14B I/O
P24 PR6C PR7C PR9C PR11C PR14C I/O
M25 PR6D PR7D PR9D PR11D PR14D I/O
N24 PR5A PR6A PR8A PR10A PR13A I/O
M26 PR5B PR6B PR8B PR10C PR13D I/O
L25 PR5C PR6C PR8C PR10D PR12A I/O
M24 PR5D PR6D PR8D PR9B PR12D I/O
L26 PR4A PR5A PR7A PR9C PR11A I/O-CS1
M23 PR4B PR5B PR7B PR9D PR11D I/O
K25 PR4C PR5C PR7C PR8A PR10A I/O
L24 PR4D PR5D PR7D PR8D PR10D I/O
K26 PR3A PR4A PR6A PR7A PR9A I/O-CS0
K23 — — PR6B PR7B PR9B I/O
J25 PR3B PR4B PR6C PR7C PR9C I/O
K24 — — PR6D PR7D PR9D I/O
J26 PR3C PR4C PR5A PR6A PR8A I/O
H25 — — PR5B PR6B PR8B I/O
H26 PR3D PR4D PR5C PR6C PR8C I/O
J24 — — PR5D PR6D PR8D I/O
G25 PR2A PR3A PR4A PR5A PR7A I/O-RD/MPI_STRB
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 73. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 352-Pin PBGA Pinout
(
continued
)
Lucent Technologies Inc. 177
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
H23 PR2B PR3B PR4B PR5B PR6A I/O
G26 — — PR4C PR5C PR6C I/O
H24 PR2C PR3C PR4D PR5D PR5A I/O
F25 PR2D PR3D PR3A PR4A PR4A I/O
G23 — — PR3B PR4B PR4B I/O
F26 — — PR3C PR4C PR4C I/O
G24 — — PR3D PR4D PR4D I/O
E25 PR1A PR2A PR2A PR3A PR3A I/O-WR
E26 PR1B PR2B PR2B PR3B PR3B I/O
F24———PR3DPR3DI/O
D25 PR1C PR2C PR2C PR2A PR2A I/O
E23 PR1D PR2D PR2D PR2D PR2D I/O
D26 — PR1A PR1A PR1A PR1A I/O
E24 — PR1B PR1B PR1B PR1B I/O
C25 — PR1C PR1C PR1C PR1C I/O
D24 — PR1D PR1D PR1D PR1D I/O
C26 PRD_CFGN PRD_CFGN PRD_CFGN PRD_CFGN PRD_CFGN RD_CFG
A25 PT12D PT14D PT18D PT22D PT28D I/O-SECKUR
B24 — PT14C PT18C PT22C PT28C I/O
A24———PT22BPT28BI/O
B23 PT12C PT14B PT18B PT22A PT28A I/O
C23 PT12B PT14A PT18A PT21D PT27D I/O
A23 PT12A PT13D PT17D PT21A PT27A I/O-RDY/RCLK/
MPI_ALE
B22 — PT13C PT17C PT20D PT26D I/O
D22 PT11D PT13B PT17B PT20C PT26C I/O
C22 PT11C PT13A PT17A PT20A PT26A I/O
A22 PT11B PT12D PT16D PT19D PT25D I/O
B21 — — PT16C PT19C PT25C I/O
D20 — — PT16B PT19B PT25B I/O
C21 — — PT16A PT19A PT25A I/O
A21 PT11A PT12C PT15D PT18D PT24D I/O-D7
B20 — — PT15C PT18C PT24C I/O
A20 — PT12B PT15B PT18B PT24B I/O
C20 — — PT15A PT18A PT24A I/O
B19 PT10D PT12A PT14D PT17D PT23D I/O
D18 — — PT14C PT17C PT23C I/O
A19 PT10C PT11D PT14B PT17B PT23B I/O
C19 — — PT14A PT17A PT22D I/O
B18 PT10B PT11C PT13D PT16D PT21D I/O
A18 — — PT13C PT16C PT21A I/O
B17 PT10A PT11B PT13B PT16B PT20D I/O-D6
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 73. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 352-Pin PBGA Pinout
(
continued
)
178 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
C18 PT9D PT11A PT13A PT16A PT20A I/O
A17 PT9C PT10D PT12D PT15D PT19D I/O
D17 — PT10C PT12C PT15B PT19A I/O
B16 PT9B PT10B PT12B PT15A PT18D I/O
C17 PT9A PT10A PT12A PT14C PT18A I/O-D5
A16 PT8D PT9D PT11D PT14B PT17D I/O
B15 PT8C PT9C PT11C PT13D PT17A I/O
A15 PT8B PT9B PT11B PT13C PT16D I/O
C16 PT8A PT9A PT11A PT13A PT16A I/O-D4
B14 PECKT PECKT PECKT PECKT PECKT I-ECKT
D15 PT7C PT8C PT10C PT12C PT15C I/O
A14 PT7B PT8B PT10B PT12B PT15B I/O
C15 PT7A PT8A PT10A PT12A PT15A I/O-D3
B13PT6DPT7DPT9DPT11DPT14D I/O
D13PT6CPT7CPT9CPT11CPT14C I/O
A13 PT6B PT7B PT9B PT11B PT14B I/O
C14 PT6A PT7A PT9A PT11A PT14A I/O-D2
B12PT5DPT6DPT8DPT10DPT13D I/O-D1
C13 PT5C PT6C PT8C PT10B PT13A I/O
A12 PT5B PT6B PT8B PT10A PT12D I/O
B11 PT5A PT6A PT8A PT9C PT12A I/O-D0/DIN
C12 PT4D PT5D PT7D PT9B PT11D I/O
A11PT4CPT5CPT7CPT8DPT11A I/O
D12 PT4B PT5B PT7B PT8C PT10D I/O
B10 PT4A PT5A PT7A PT8A PT10A I/O-DOUT
C11 PT3D PT4D PT6D PT7D PT9D I/O
A10 — — PT6C PT7C PT9A I/O
D10 — — PT6B PT7B PT8D I/O
B9 PT3C PT4C PT6A PT7A PT8A I/O
C10 PT3B PT4B PT5D PT6D PT7D I/O
A9 — — PT5C PT6C PT7A I/O
B8 — — PT5B PT6B PT6D I/O
A8 PT3A PT4A PT5A PT6A PT6A I/O-TDI
C9 — — PT4D PT5D PT5D I/O
B7 PT2D PT3D PT4C PT5C PT5C I/O
D8 — — PT4B PT5B PT5B I/O
A7 PT2C PT3C PT4A PT5A PT5A I/O
C8 — — PT3D PT4D PT4D I/O
B6 PT2B PT3B PT3C PT4C PT4C I/O
D7 — — PT3B PT4B PT4B I/O
A6 PT2A PT3A PT3A PT4A PT4A I/O-TMS
C7 — PT2D PT2D PT3D PT3D I/O
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 73. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 352-Pin PBGA Pinout
(
continued
)
Lucent Technologies Inc. 179
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
B5 PT1D PT2C PT2C PT3A PT3A I/O
A5 PT1C PT2B PT2B PT2D PT2D I/O
C6 — — — PT2C PT2C I/O
B4 — — — PT2B PT2B I/O
D5 PT1B PT2A PT2A PT2A PT2A I/O
A4 — PT1D PT1D PT1D PT1D I/O
C5 — PT1C PT1C PT1C PT1C I/O
B3 — PT1B PT1B PT1B PT1B I/O
C4 PT1A PT1A PT1A PT1A PT1A I/O-TCK
A3 PRD_DATA PRD_DATA PRD_DATA PRD_DATA PRD_DATA RD_DATA/TDO
A1 VSS VSS VSS VSS VSS VSS
A2 VSS VSS VSS VSS VSS VSS
A26 VSS VSS VSS VSS VSS VSS
AC13 VSS VSS VSS VSS VSS VSS
AC18 VSS VSS VSS VSS VSS VSS
AC23 VSS VSS VSS VSS VSS VSS
AC4 VSS VSS VSS VSS VSS VSS
AC8 VSS VSS VSS VSS VSS VSS
AD24 VSS VSS VSS VSS VSS VSS
AD3 VSS VSS VSS VSS VSS VSS
AE1 VSS VSS VSS VSS VSS VSS
AE2 VSS VSS VSS VSS VSS VSS
AE25 VSS VSS VSS VSS VSS VSS
AF1 VSS VSS VSS VSS VSS VSS
AF25 VSS VSS VSS VSS VSS VSS
AF26 VSS VSS VSS VSS VSS VSS
B2 VSS VSS VSS VSS VSS VSS
B25 VSS VSS VSS VSS VSS VSS
B26 VSS VSS VSS VSS VSS VSS
C24 VSS VSS VSS VSS VSS VSS
C3 VSS VSS VSS VSS VSS VSS
D14 VSS VSS VSS VSS VSS VSS
D19 VSS VSS VSS VSS VSS VSS
D23 VSS VSS VSS VSS VSS VSS
D4 VSS VSS VSS VSS VSS VSS
D9 VSS VSS VSS VSS VSS VSS
H4 VSS VSS VSS VSS VSS VSS
J23 VSS VSS VSS VSS VSS VSS
N4 VSS VSS VSS VSS VSS VSS
P23 VSS VSS VSS VSS VSS VSS
V4 VSS VSS VSS VSS VSS VSS
W23 VSS VSS VSS VSS VSS VSS
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 73. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 352-Pin PBGA Pinout
(
continued
)
180 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
L11 VSS VSS VSS VSS VSS VSS*
L12 VSS VSS VSS VSS VSS VSS*
L13 VSS VSS VSS VSS VSS VSS*
L14 VSS VSS VSS VSS VSS VSS*
L15 VSS VSS VSS VSS VSS VSS*
L16 VSS VSS VSS VSS VSS VSS*
M11 VSS VSS VSS VSS VSS VSS*
M12 VSS VSS VSS VSS VSS VSS*
M13 VSS VSS VSS VSS VSS VSS*
M14 VSS VSS VSS VSS VSS VSS*
M15 VSS VSS VSS VSS VSS VSS*
M16 VSS VSS VSS VSS VSS VSS*
N11 VSS VSS VSS VSS VSS VSS*
N12 VSS VSS VSS VSS VSS VSS*
N13 VSS VSS VSS VSS VSS VSS*
N14 VSS VSS VSS VSS VSS VSS*
N15 VSS VSS VSS VSS VSS VSS*
N16 VSS VSS VSS VSS VSS VSS*
P11 VSS VSS VSS VSS VSS VSS*
P12 VSS VSS VSS VSS VSS VSS*
P13 VSS VSS VSS VSS VSS VSS*
P14 VSS VSS VSS VSS VSS VSS*
P15 VSS VSS VSS VSS VSS VSS*
P16 VSS VSS VSS VSS VSS VSS*
R11 VSS VSS VSS VSS VSS VSS*
R12 VSS VSS VSS VSS VSS VSS*
R13 VSS VSS VSS VSS VSS VSS*
R14 VSS VSS VSS VSS VSS VSS*
R15 VSS VSS VSS VSS VSS VSS*
R16 VSS VSS VSS VSS VSS VSS*
T11 VSS VSS VSS VSS VSS VSS*
T12 VSS VSS VSS VSS VSS VSS*
T13 VSS VSS VSS VSS VSS VSS*
T14 VSS VSS VSS VSS VSS VSS*
T15 VSS VSS VSS VSS VSS VSS*
T16 VSS VSS VSS VSS VSS VSS*
AA23 VDD VDD VDD VDD VDD VDD
AA4 VDD VDD VDD VDD VDD VDD
AC11 VDD VDD VDD VDD VDD VDD
AC16 VDD VDD VDD VDD VDD VDD
AC21 VDD VDD VDD VDD VDD VDD
AC6 VDD VDD VDD VDD VDD VDD
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 73. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 352-Pin PBGA Pinout
(
continued
)
Lucent Technologies Inc. 181
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
*Thermall
y
enhanced connection.
D11 VDD VDD VDD VDD VDD VDD
D16 VDD VDD VDD VDD VDD VDD
D21 VDD VDD VDD VDD VDD VDD
D6 VDD VDD VDD VDD VDD VDD
F23 VDD VDD VDD VDD VDD VDD
F4 VDD VDD VDD VDD VDD VDD
L23 VDD VDD VDD VDD VDD VDD
L4 VDD VDD VDD VDD VDD VDD
T23 VDD VDD VDD VDD VDD VDD
T4 VDD VDD VDD VDD VDD VDD
Pin OR3T20
Pad OR3T30
Pad OR3C/T55
Pad OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 73. OR3T20, OR3T30, OR3C/T55, OR3C/T80, and OR3T125 352-Pin PBGA Pinout
(
continued
)
182182 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Pin OR3C/T80
Pad OR3T125
Pad Function
E4 PRD_CFGN PRD_CFGN RD_CFG
D3 PR1D PR1D I/O
D2 PR1C PR1C I/O
D1 PR1B PR1B I/O
F4 PR1A PR1A I/O
E3 PR2D PR2D I/O
E2 PR2C PR2C I/O
E1 PR2B PR2B I/O
F3 PR2A PR2A I/O
F2 PR3D PR3D I/O
F1 PR3C PR3C I/O
H4 PR3B PR3B I/O
G3 PR3A PR3A I/O-WR
G2 PR4D PR4D I/O
G1 PR4C PR4C I/O
J4 PR4B PR4B I/O
H3 PR4A PR4A I/O
H2 PR5D PR5A I/O
J3 PR5C PR6C I/O
K4 PR5B PR6A I/O
J2 PR5A PR7A I/O-RD/MPI_STRB
J1 PR6D PR8D I/O
K3 PR6C PR8C I/O
K2 PR6B PR8B I/O
K1 PR6A PR8A I/O
L3 PR7D PR9D I/O
M4 PR7C PR9C I/O
L2 PR7B PR9B I/O
L1 PR7A PR9A I/O-CS0
M3 PR8D PR10D I/O
N4 PR8A PR10A I/O
M2 PR9D PR11D I/O
N3 PR9C PR11A I/O-CS1
N2 PR9B PR12D I/O
P4 PR9A PR12C I/O
N1 PR10D PR12A I/O
P3 PR10C PR13D I/O
P2 PR10B PR13C I/O
P1 PR10A PR13A I/O
R3 PR11D PR14D I/O
R2 PR11C PR14C I/O
R1 PR11B PR14B I/O
T2 PECKR PECKR I-ECKR
T4 PR12D PR15D I/O
T3 PR12C PR15C I/O
U1 PR12B PR15B I/O
U2 PR12A PR15A I/O
U3 PR13D PR16D I/O
V1 PR13C PR16B I/O
V2 PR13B PR16A I/O
V3 PR13A PR17D I/O
W1 PR14D PR17A I/O-M3
V4 PR14C PR18D I/O
W2 PR14B PR18B I/O
W3 PR14A PR18A I/O
Y2 PR15D PR19D I/O
W4 PR15A PR19A I/O-M2
Y3 PR16D PR20D I/O
AA1 PR16C PR20C I/O
AA2 PR16B PR20B I/O
Y4 PR16A PR20A I/O
AA3 PR17D PR21D I/O
AB1 PR17C PR21C I/O
AB2 PR17B PR21B I/O
AB3 PR17A PR21A I/O
AC1 PR18D PR22D I/O-M1
AC2 PR18C PR23D I/O
AB4 PR18B PR23B I/O
AC3 PR18A PR23A I/O
AD2 PR19D PR24A I/O
AD3 PR19C PR25C I/O
AC4 PR19B PR25B I/O
AE1 PR19A PR25A I/O
AE2 PR20D PR26D I/O
AE3 PR20C PR26C I/O
AD4 PR20B PR26B I/O
AF1 PR20A PR26A I/O
AF2 PR21D PR27D I/O
AF3 PR21C PR27C I/O
AG1 PR21B PR27B I/O
AG2 PR21A PR27A I/O
AG3 PR22D PR28D I/O
AF4 PR22C PR28C I/O
AH1 PR22B PR28B I/O
AH2 PR22A PR28A I/O-M0
AH3 PPRGMN PPRGMN PRGM
AG4 PRESETN PRESETN RESET
AH5 PDONE PDONE DONE
AJ4 PB22D PB28D I/O
AK4 PB22C PB28C I/O
AL4 PB22B PB28B I/O
AH6 PB22A PB28A I/O
Pin OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 74. OR3C/T80 and OR3T125 432-Pin EBGA Pinout
Lucent Technologies Inc. 183
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
AJ5 PB21D PB27D I/O
AK5 PB21C PB27C I/O
AL5 PB21B PB27B I/O
AJ6 PB21A PB27A I/O
AK6 PB20D PB26D I/O
AL6 PB20C PB26C I/O
AH8 PB20B PB26B I/O
AJ7 PB20A PB26A I/O
AK7 PB19D PB25D I/O
AL7 PB19C PB25C I/O
AH9 PB19B PB25B I/O
AJ8 PB19A PB25A I/O
AK8 PB18D PB24D I/O
AJ9 PB18C PB24C I/O
AH10 PB18B PB24B I/O
AK9 PB18A PB24A I/O-INIT
AL9 PB17D PB23D I/O
AJ10 PB17C PB23C I/O
AK10 PB17B PB23A I/O
AL10 PB17A PB22A I/O
AJ11 PB16D PB21D I/O
AH12 PB16C PB21A I/O
AK11 PB16B PB20D I/O
AL11 PB16A PB20A I/O-LDC
AJ12 PB15D PB19D I/O
AH13 PB15B PB19B I/O
AK12 PB15A PB19A I/O
AJ13 PB14D PB18D I/O
AK13 PB14C PB18B I/O
AH14 PB14B PB18A I/O-HDC
AL13 PB14A PB17D I/O
AJ14 PB13D PB17B I/O
AK14 PB13C PB17A I/O
AL14 PB13B PB16D I/O
AJ15 PB13A PB16A I/O
AK15 PB12D PB15D I/O
AL15 PB12C PB15C I/O
AK16 PB12B PB15B I/O
AH16 PECKB PECKB I-ECKB
AJ16 PB11D PB14D I/O
AL17 PB11C PB14C I/O
AK17 PB11B PB14B I/O
AJ17 PB11A PB14A I/O
AL18 PB10D PB13D I/O
AK18 PB10C PB13B I/O
AJ18 PB10B PB13A I/O
Pin OR3C/T80
Pad OR3T125
Pad Function
AL19 PB10A PB12D I/O
AH18 PB9D PB12A I/O
AK19 PB9C PB11D I/O
AJ19 PB9B PB11B I/O
AK20 PB9A PB11A I/O
AH19 PB8D PB10D I/O
AJ20 PB8B PB10B I/O
AL21 PB8A PB10A I/O
AK21 PB7D PB9D I/O
AH20 PB7C PB9A I/O
AJ21 PB7B PB8D I/O
AL22 PB7A PB8A I/O
AK22 PB6D PB7D I/O
AJ22 PB6C PB7A I/O
AL23 PB6B PB6D I/O
AK23 PB6A PB6A I/O
AH22 PB5D PB5D I/O
AJ23 PB5C PB5C I/O
AK24 PB5B PB5B I/O
AJ24 PB5A PB5A I/O
AH23 PB4D PB4D I/O-A17
AL25 PB4C PB4C I/O
AK25 PB4B PB4B I/O
AJ25 PB4A PB4A I/O
AH24 PB3D PB3D I/O
AL26 PB3C PB3C I/O
AK26 PB3B PB3B I/O
AJ26 PB3A PB3A I/O
AL27 PB2D PB2D I/O
AK27 PB2C PB2C I/O
AJ27 PB2B PB2B I/O
AH26 PB2A PB2A I/O
AL28 PB1D PB1D I/O
AK28 PB1C PB1C I/O
AJ28 PB1B PB1B I/O
AH27 PB1A PB1A I/O-A16
AG28 PCCLK PCCLK CCLK
AH29 PL22A PL28A I/O-A15
AH30 PL22B PL28B I/O
AH31 PL22C PL28C I/O
AF28 PL22D PL28D I/O
AG29 PL21A PL27A I/O-SECKLL
AG30 PL21B PL27B I/O
AG31 PL21C PL27C I/O
AF29 PL21D PL27D I/O
AF30 PL20A PL26A I/O
Pin OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 74. OR3C/T80 and OR3T125 432-Pin EBGA Pinout
(
continued
)
184184 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
AF31 PL20B PL26B I/O
AD28 PL20C PL26C I/O
AE29 PL20D PL26D I/O
AE30 PL19A PL25A I/O
AE31 PL19B PL25B I/O
AC28 PL19C PL25C I/O
AD29 PL19D PL24A I/O-A14
AD30 PL18A PL24D I/O
AC29 PL18B PL23D I/O
AB28 PL18C PL22C I/O
AC30 PL18D PL22D I/O
AC31 PL17A PL21A I/O
AB29 PL17B PL21B I/O-A13
AB30 PL17C PL21C I/O
AB31 PL17D PL21D I/O
AA29 PL16A PL20A I/O
Y28 PL16B PL20B I/O
AA30 PL16C PL20C I/O
AA31 PL16D PL20D I/O-A12
Y29 PL15A PL19A I/O-A11/MPI_IRQ
W28 PL15B PL19D I/O
Y30 PL15C PL18A I/O
W29 PL14A PL18C I/O
W30 PL14B PL18D I/O
V28 PL14C PL17A I/O-A10/MPI_BI
W31 PL14D PL17C I/O
V29 PL13A PL17D I/O
V30 PL13B PL16A I/O
V31 PL13C PL16C I/O
U29 PL13D PL16D I/O-A9/MPI_ACK
U30 PL12A PL15A I/O-A8/MPI_RW
U31 PL12B PL15B I/O
T30 PL12C PL15C I/O
T28 PL12D PL15D I/O
T29 PL11A PL14A I/O-A7/MPI_CLK
R31 PL11B PL14B I/O
R30 PL11C PL14C I/O
R29 PECKL PECKL I-ECKL
P31 PL10A PL13A I/O-A6
P30 PL10B PL13D I/O
P29 PL10C PL12A I/O
N31 PL10D PL12C I/O
P28 PL9A PL12D I/O-A5
N30 PL9B PL11A I/O-A4
N29 PL9C PL11C I/O
M30 PL9D PL11D I/O
Pin OR3C/T80
Pad OR3T125
Pad Function
N28 PL8A PL10A I/O
M29 PL8C PL10C I/O
L31 PL8D PL10D I/O
L30 PL7A PL9A I/O-A3
M28 PL7B PL9B I/O
L29 PL7C PL9C I/O
K31 PL7D PL9D I/O
K30 PL6A PL8A I/O-A2
K29 PL6B PL8B I/O
J31 PL6C PL8C I/O
J30 PL6D PL8D I/O
K28 PL5A PL7D I/O-A1/MPI_BE1
J29 PL5B PL6B I/O
H30 PL5C PL6C I/O
H29 PL5D PL6D I/O
J28 PL4A PL5D I/O
G31 PL4B PL4B I/O
G30 PL4C PL4C I/O
G29 PL4D PL4D I/O
H28 PL3A PL3A I/O
F31 PL3B PL3B I/O
F30 PL3C PL3C I/O
F29 PL3D PL3D I/O
E31 PL2A PL2A I/O
E30 PL2B PL2B I/O
E29 PL2C PL2C I/O
F28 PL2D PL2D I/O-A0/MPI_BE0
D31 PL1A PL1A I/O
D30 PL1B PL1B I/O
D29 PL1C PL1C I/O
E28 PL1D PL1D I/O
D27 PRD_DATA PRD_DATA RD_DATA/TDO
C28 PT1A PT1A I/O-TCK
B28 PT1B PT1B I/O
A28 PT1C PT1C I/O
D26 PT1D PT1D I/O
C27 PT2A PT2A I/O
B27 PT2B PT2B I/O
A27 PT2C PT2C I/O
C26 PT2D PT2D I/O
B26 PT3A PT3A I/O
A26 PT3B PT3B I/O
D24 PT3C PT3C I/O
C25 PT3D PT3D I/O
B25 PT4A PT4A I/O-TMS
A25 PT4B PT4B I/O
Pin OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 74. OR3C/T80 and OR3T125 432-Pin EBGA Pinout
(
continued
)
Lucent Technologies Inc. 185
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
D23 PT4C PT4C I/O
C24 PT4D PT4D I/O
B24 PT5A PT5A I/O
C23 PT5B PT5B I/O
D22 PT5C PT5C I/O
B23 PT5D PT5D I/O
A23 PT6A PT6A I/O-TDI
C22 PT6B PT6D I/O
B22 PT6C PT7A I/O
A22 PT6D PT7D I/O
C21 PT7A PT8A I/O
D20 PT7B PT8D I/O
B21 PT7C PT9A I/O
A21 PT7D PT9D I/O
C20 PT8A PT10A I/O-DOUT
D19 PT8C PT10D I/O
B20 PT8D PT11A I/O
C19 PT9A PT11C I/O
B19 PT9B PT11D I/O
D18 PT9C PT12A I/O-D0/DIN
A19 PT9D PT12C I/O
C18 PT10A PT12D I/O
B18 PT10B PT13A I/O
A18 PT10C PT13C I/O
C17 PT10D PT13D I/O-D1
B17 PT11A PT14A I/O-D2
A17 PT11B PT14B I/O
B16 PT11C PT14C I/O
D16 PT11D PT14D I/O
C16 PT12A PT15A I/O-D3
A15 PT12B PT15B I/O
B15 PT12C PT15C I/O
C15 PECKT PECKT I-ECKT
A14 PT13A PT16A I/O-D4
B14 PT13B PT16B I/O
C14 PT13C PT16D I/O
A13 PT13D PT17A I/O
D14 PT14A PT17B I/O
B13 PT14B PT17D I/O
C13 PT14C PT18A I/O-D5
B12 PT14D PT18B I/O
D13 PT15A PT18D I/O
C12 PT15B PT19A I/O
A11 PT15D PT19D I/O
B11 PT16A PT20A I/O
D12 PT16B PT20D I/O-D6
Pin OR3C/T80
Pad OR3T125
Pad Function
C11 PT16C PT21A I/O
A10 PT16D PT21D I/O
B10 PT17A PT22D I/O
C10 PT17B PT23B I/O
A9 PT17C PT23C I/O
B9 PT17D PT23D I/O
D10 PT18A PT24A I/O
C9 PT18B PT24B I/O
B8 PT18C PT24C I/O
C8 PT18D PT24D I/O-D7
D9 PT19A PT25A I/O
A7 PT19B PT25B I/O
B7 PT19C PT25C I/O
C7 PT19D PT25D I/O
D8 PT20A PT26A I/O
A6 PT20B PT26B I/O
B6 PT20C PT26C I/O
C6 PT20D PT26D I/O
A5 PT21A PT27A I/O-RDY/RCLK/MPI_ALE
B5 PT21B PT27B I/O
C5 PT21C PT27C I/O
D6 PT21D PT27D I/O
A4 PT22A PT28A I/O
B4 PT22B PT28B I/O
C4 PT22C PT28C I/O
D5 PT22D PT28D I/O-SECKUR
A12 VSS VSS VSS
A16 VSS VSS VSS
A2 VSS VSS VSS
A20 VSS VSS VSS
A24 VSS VSS VSS
A29 VSS VSS VSS
A3 VSS VSS VSS
A30 VSS VSS VSS
A8 VSS VSS VSS
AD1 VSS VSS VSS
AD31 VSS VSS VSS
AJ1 VSS VSS VSS
AJ2 VSS VSS VSS
AJ30 VSS VSS VSS
AJ31 VSS VSS VSS
AK1 VSS VSS VSS
AK29 VSS VSS VSS
AK3 VSS VSS VSS
AK31 VSS VSS VSS
AL12 VSS VSS VSS
Pin OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 74. OR3C/T80 and OR3T125 432-Pin EBGA Pinout
(
continued
)
186186 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
AL16 VSS VSS VSS
AL2 VSS VSS VSS
AL20 VSS VSS VSS
AL24 VSS VSS VSS
AL29 VSS VSS VSS
AL3 VSS VSS VSS
AL30 VSS VSS VSS
AL8 VSS VSS VSS
B1 VSS VSS VSS
B29 VSS VSS VSS
B3 VSS VSS VSS
B31 VSS VSS VSS
C1 VSS VSS VSS
C2 VSS VSS VSS
C30 VSS VSS VSS
C31 VSS VSS VSS
H1 VSS VSS VSS
H31 VSS VSS VSS
M1 VSS VSS VSS
M31 VSS VSS VSS
T1 VSS VSS VSS
T31 VSS VSS VSS
Y1 VSS VSS VSS
Y31 VSS VSS VSS
A1 VDD VDD VDD
A31 VDD VDD VDD
AA28 VDD VDD VDD
AA4 VDD VDD VDD
AE28 VDD VDD VDD
AE4 VDD VDD VDD
AH11 VDD VDD VDD
AH15 VDD VDD VDD
Pin OR3C/T80
Pad OR3T125
Pad Function
AH17 VDD VDD VDD
AH21 VDD VDD VDD
AH25 VDD VDD VDD
AH28 VDD VDD VDD
AH4 VDD VDD VDD
AH7 VDD VDD VDD
AJ29 VDD VDD VDD
AJ3 VDD VDD VDD
AK2 VDD VDD VDD
AK30 VDD VDD VDD
AL1 VDD VDD VDD
AL31 VDD VDD VDD
B2 VDD VDD VDD
B30 VDD VDD VDD
C29 VDD VDD VDD
C3 VDD VDD VDD
D11 VDD VDD VDD
D15 VDD VDD VDD
D17 VDD VDD VDD
D21 VDD VDD VDD
D25 VDD VDD VDD
D28 VDD VDD VDD
D4 VDD VDD VDD
D7 VDD VDD VDD
G28 VDD VDD VDD
G4 VDD VDD VDD
L28 VDD VDD VDD
L4 VDD VDD VDD
R28 VDD VDD VDD
R4 VDD VDD VDD
U28 VDD VDD VDD
U4 VDD VDD VDD
Pin OR3C/T80
Pad OR3T125
Pad Function
Pin Information
(
continued
)
Table 74. OR3C/T80 and OR3T125 432-Pin EBGA Pinout
(
continued
)
Lucent Technologies Inc. 187
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Pin OR3T125
Pad Function
E4 PRD_CFGN RD_CFG
E3 PR1D I/O
E2 PR1C I/O
F5 PR1B I/O
F4 PR1A I/O
F3 PR2D I/O
F2 PR2C I/O
G5 PR2B I/O
G4 PR2A I/O
G3 PR3D I/O
G2 PR3C I/O
H5 PR3B I/O
H4 PR3A I/O-WR
H3 PR4D I/O
H2 PR4C I/O
J5 PR4B I/O
J4 PR4A I/O
J3 PR5D I/O
J2 PR5C I/O
J1 PR5B I/O
K5 PR5A I/O
K4 PR6D I/O
K3 PR6C I/O
K2 PR6B I/O
K1 PR6A I/O
L4 PR7D I/O
L3 PR7C I/O
L2 PR7B I/O
L1 PR7A I/O-RD/MPI_STRB
M5 PR8D I/O
M4 PR8C I/O
M3 PR8B I/O
M2 PR8A I/O
M1 PR9D I/O
N5 PR9C I/O
N4 PR9B I/O
N3 PR9A I/O-CS0
N2 PR10D I/O
P4 PR10C I/O
P5 PR10B I/O
P3 PR10A I/O
P2 PR11D I/O
P1 PR11C I/O
R4 PR11B I/O
R5 PR11A I/O-CS1
R3 PR12D I/O
R2 PR12C I/O
R1 PR12B I/O
T4 PR12A I/O
T3 PR13D I/O
T2 PR13C I/O
U2 PR13B I/O
U4 PR13A I/O
U5 PR14D I/O
U3 PR14C I/O
U1 PR14B I/O
V2 PECKR I-ECKR
V4 PR15D I/O
V5 PR15C I/O
V3 PR15B I/O
W2 PR15A I/O
W3 PR16D I/O
W4 PR16C I/O
W5 PR16B I/O
Y2 PR16A I/O
Y3 PR17D I/O
Y4 PR17C I/O
AA1 PR17B I/O
AA2 PR17A I/O-M3
AA3 PR18D I/O
AA4 PR18C I/O
AA5 PR18B I/O
AB1 PR18A I/O
AB2 PR19D I/O
AB3 PR19C I/O
AB4 PR19B I/O
AB5 PR19A I/O-M2
AC2 PR20D I/O
AC3 PR20C I/O
AC4 PR20B I/O
AC5 PR20A I/O
AD1 PR21D I/O
AD2 PR21C I/O
AD3 PR21B I/O
AD4 PR21A I/O
AD5 PR22D I/O-M1
AE1 PR22C I/O
AE2 PR22B I/O
AE3 PR22A I/O
AE4 PR23D I/O
AF1 PR23C I/O
AF2 PR23B I/O
Pin OR3T125
Pad Function
Pin Information
(
continued
)
Table 75. OR3T125 600-Pin EBGA Pinout
188188 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
AF3 PR23A I/O
AF4 PR24D I/O
AF5 PR24C I/O
AG1 PR24B I/O
AG2 PR24A I/O
AG3 PR25D I/O
AG4 PR25C I/O
AG5 PR25B I/O
AH2 PR25A I/O
AH3 PR26D I/O
AH4 PR26C I/O
AH5 PR26B I/O
AJ2 PR26A I/O
AJ3 PR27D I/O
AJ4 PR27C I/O
AJ5 PR27B I/O
AK2 PR27A I/O
AK3 PR28D I/O
AK4 PR28C I/O
AK5 PR28B I/O
AL2 PR28A I/O-M0
AL3 PPRGMN PRGM
AL4 PRESETN RESET
AM5 PDONE DONE
AN5 PB28D I/O
AP5 PB28C I/O
AL6 — I/O
AM6 PB28B I/O
AN6 PB28A I/O
AP6 PB27D I/O
AL7 PB27C I/O
AM7 PB27B I/O
AN7 PB27A I/O
AP7 PB26D I/O
AL8 PB26C I/O
AM8 PB26B I/O
AN8 PB26A I/O
AP8 PB25D I/O
AL9 PB25C I/O
AM9 PB25B I/O
AN9 PB25A I/O
AP9 PB24D I/O
AR9 PB24C I/O
AL10 PB24B I/O
AM10 PB24A I/O-INIT
AN10 PB23D I/O
Pin OR3T125
Pad Function
AP10 PB23C I/O
AR10 PB23B I/O
AM11 PB23A I/O
AN11 PB22D I/O
AP11 PB22C I/O
AR11 PB22B I/O
AL12 PB22A I/O
AM12 PB21D I/O
AN12 PB21C I/O
AP12 PB21B I/O
AR12 PB21A I/O
AL13 PB20D I/O
AM13 PB20C I/O
AN13 PB20B I/O
AP13 PB20A I/O-LDC
AM14 PB19D I/O
AL14 PB19C I/O
AN14 PB19B I/O
AP14 PB19A I/O
AR14 PB18D I/O
AM15 PB18C I/O
AL15 PB18B I/O
AN15 PB18A I/O-HDC
AP15 PB17D I/O
AR15 PB17C I/O
AM16 PB17B I/O
AN16 PB17A I/O
AP16 PB16D I/O
AP17 PB16C I/O
AM17 PB16B I/O
AL17 PB16A I/O
AN17 PB15D I/O
AR17 PB15C I/O
AP18 PB15B I/O
AM18 PECKB I-ECKB
AL18 PB14D I/O
AN18 PB14C I/O
AP19 PB14B I/O
AN19 PB14A I/O
AM19 PB13D I/O
AL19 PB13C I/O
AP20 PB13B I/O
AN20 PB13A I/O
AM20 PB12D I/O
AR21 PB12C I/O
AP21 PB12B I/O
Pin OR3T125
Pad Function
Pin Information
(
continued
)
Table 75. OR3T125 600-Pin EBGA Pinout
(
continued
)
Lucent Technologies Inc. 189
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
AN21 PB12A I/O
AM21 PB11D I/O
AL21 PB11C I/O
AR22 PB11B I/O
AP22 PB11A I/O
AN22 PB10D I/O
AM22 PB10C I/O
AL22 PB10B I/O
AP23 PB10A I/O
AN23 PB9D I/O
AM23 PB9C I/O
AL23 PB9B I/O
AR24 PB9A I/O
AP24 PB8D I/O
AN24 PB8C I/O
AM24 PB8B I/O
AL24 PB8A I/O
AR25 PB7D I/O
AP25 PB7C I/O
AN25 PB7B I/O
AM25 PB7A I/O
AR26 PB6D I/O
AP26 PB6C I/O
AN26 PB6B I/O
AM26 PB6A I/O
AL26 PB5D I/O
AR27 PB5C I/O
AP27 PB5B I/O
AN27 PB5A I/O
AM27 PB4D I/O-A17
AL27 PB4C I/O
AP28 PB4B I/O
AN28 PB4A I/O
AM28 PB3D I/O
AL28 PB3C I/O
AP29 PB3B I/O
AN29 PB3A I/O
AM29 PB2D I/O
AL29 PB2C I/O
AP30 PB2B I/O
AN30 PB2A I/O
AM30 PB1D I/O
AL30 PB1C I/O
AP31 — I/O
AN31 PB1B I/O
AM31 PB1A I/O-A16
Pin OR3T125
Pad Function
AL32 PCCLK CCLK
AL33 PL28A I/O-A15
AL34 PL28B I/O
AK31 PL28C I/O
AK32 PL28D I/O
AK33 — I/O
AK34 PL27A I/O-SECKLL
AJ31 PL27B I/O
AJ32 PL27C I/O
AJ33 PL27D I/O
AJ34 PL26A I/O
AH31 PL26B I/O
AH32 PL26C I/O
AH33 PL26D I/O
AH34 PL25A I/O
AG31 PL25B I/O
AG32 PL25C I/O
AG33 PL25D I/O
AG34 PL24A I/O-A14
AG35 PL24B I/O
AF31 PL24C I/O
AF32 PL24D I/O
AF33 PL23A I/O
AF34 PL23B I/O
AF35 PL23C I/O
AE32 PL23D I/O
AE33 PL22A I/O
AE34 PL22B I/O
AE35 PL22C I/O
AD31 PL22D I/O
AD32 PL21A I/O
AD33 PL21B I/O-A13
AD34 PL21C I/O
AD35 PL21D I/O
AC31 PL20A I/O
AC32 PL20B I/O
AC33 PL20C I/O
AC34 PL20D I/O-A12
AB32 PL19A I/O-A11/MPI_IRQ
AB31 PL19B I/O
AB33 PL19C I/O
AB34 PL19D I/O
AB35 PL18A I/O
AA32 PL18B I/O
AA31 PL18C I/O
AA33 PL18D I/O
Pin OR3T125
Pad Function
Pin Information
(
continued
)
Table 75. OR3T125 600-Pin EBGA Pinout
(
continued
)
190190 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
AA34 PL17A I/O-A10/MPI_BI
AA35 PL17B I/O
Y32 PL17C I/O
Y33 PL17D I/O
Y34 PL16A I/O
W34 PL16B I/O
W32 PL16C I/O
W31 PL16D I/O-A9/MPI_ACK
W33 PL15A I/O-A8/MPI_RW
W35 PL15B I/O
V34 PL15C I/O
V32 PL15D I/O
V31 PL14A I/O-A7/MPI_CLK
V33 PL14B I/O
U34 PL14C I/O
U33 PECKL I-ECKL
U32 PL13A I/O-A6
U31 PL13B I/O
T34 PL13C I/O
T33 PL13D I/O
T32 PL12A I/O
R35 PL12B I/O
R34 PL12C I/O
R33 PL12D I/O-A5
R32 PL11A I/O-A4
R31 PL11B I/O
P35 PL11C I/O
P34 PL11D I/O
P33 PL10A I/O
P32 PL10B I/O
P31 PL10C I/O
N34 PL10D I/O
N33 PL9A I/O-A3
N32 PL9B I/O
N31 PL9C I/O
M35 PL9D I/O
M34 PL8A I/O-A2
M33 PL8B I/O
M32 PL8C I/O
M31 PL8D I/O
L35 PL7A I/O
L34 PL7B I/O
L33 PL7C I/O
L32 PL7D I/O-A1/MPI_BE1
K35 PL6A I/O
K34 PL6B I/O
Pin OR3T125
Pad Function
K33 PL6C I/O
K32 PL6D I/O
K31 PL5A I/O
J35 PL5B I/O
J34 PL5C I/O
J33 PL5D I/O
J32 PL4A I/O
J31 PL4B I/O
H34 PL4C I/O
H33 PL4D I/O
H32 PL3A I/O
H31 PL3B I/O
G34 PL3C I/O
G33 PL3D I/O
G32 PL2A I/O
G31 PL2B I/O
F34 PL2C I/O
F33 PL2D I/O-A0/MPI_BE0
F32 PL1A I/O
F31 PL1B I/O
E34 PL1C I/O
E33 — I/O
E32 PL1D I/O
D31 PRD_DATA RD_DATA/TDO
C31 PT1A I/O-TCK
B31 — I/O
E30 PT1B I/O
D30 PT1C I/O
C30 PT1D I/O
B30 PT2A I/O
E29 PT2B I/O
D29 PT2C I/O
C29 PT2D I/O
B29 PT3A I/O
E28 PT3B I/O
D28 PT3C I/O
C28 PT3D I/O
B28 PT4A I/O-TMS
E27 PT4B I/O
D27 PT4C I/O
C27 PT4D I/O
B27 PT5A I/O
A27 PT5B I/O
E26 PT5C I/O
D26 PT5D I/O
C26 PT6A I/O-TDI
Pin OR3T125
Pad Function
Pin Information
(
continued
)
Table 75. OR3T125 600-Pin EBGA Pinout
(
continued
)
Lucent Technologies Inc. 191
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
B26 PT6B I/O
A26 PT6C I/O
D25 PT6D I/O
C25 PT7A I/O
B25 PT7B I/O
A25 PT7C I/O
E24 PT7D I/O
D24 PT8A I/O
C24 PT8B I/O
B24 PT8C I/O
A24 PT8D I/O
E23 PT9A I/O
D23 PT9B I/O
C23 PT9C I/O
B23 PT9D I/O
D22 PT10A I/O-DOUT
E22 PT10B I/O
C22 PT10C I/O
B22 PT10D I/O
A22 PT11A I/O
D21 PT11B I/O
E21 PT11C I/O
C21 PT11D I/O
B21 PT12A I/O-D0/DIN
A21 PT12B I/O
D20 PT12C I/O
C20 PT12D I/O
B20 PT13A I/O
B19 PT13B I/O
D19 PT13C I/O
E19 PT13D I/O-D1
C19 PT14A I/O-D2
A19 PT14B I/O
B18 PT14C I/O
D18 PT14D I/O
E18 PT15A I/O-D3
C18 PT15B I/O
B17 PT15C I/O
C17 PECKT I-ECKT
D17 PT16A I/O-D4
E17 PT16B I/O
B16 PT16C I/O
C16 PT16D I/O
D16 PT17A I/O
A15 PT17B I/O
B15 PT17C I/O
Pin OR3T125
Pad Function
C15 PT17D I/O
D15 PT18A I/O-D5
E15 PT18B I/O
A14 PT18C I/O
B14 PT18D I/O
C14 PT19A I/O
D14 PT19B I/O
E14 PT19C I/O
B13 PT19D I/O
C13 PT20A I/O
D13 PT20B I/O
E13 PT20C I/O
A12 PT20D I/O-D6
B12 PT21A I/O
C12 PT21B I/O
D12 PT21C I/O
E12 PT21D I/O
A11 PT22A I/O
B11 PT22B I/O
C11 PT22C I/O
D11 PT22D I/O
A10 PT23A I/O
B10 PT23B I/O
C10 PT23C I/O
D10 PT23D I/O
E10 PT24A I/O
A9 PT24B I/O
B9 PT24C I/O
C9 PT24D I/O-D7
D9 PT25A I/O
E9 PT25B I/O
B8 PT25C I/O
C8 PT25D I/O
D8 PT26A I/O
E8 PT26B I/O
B7 PT26C I/O
C7 PT26D I/O
D7 PT27A I/O-RDY/RCLK/MPI_ALE
E7 PT27B I/O
B6 PT27C I/O
C6 PT27D I/O
D6 PT28A I/O
E6 PT28B I/O
B5 PT28C I/O
C5 — I/O
D5 PT28D I/O-SECKUR
Pin OR3T125
Pad Function
Pin Information
(
continued
)
Table 75. OR3T125 600-Pin EBGA Pinout
(
continued
)
192192 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
A13 VSS VSS
A16 VSS VSS
A20 VSS VSS
A23 VSS VSS
A28 VSS VSS
A29 VSS VSS
A3 VSS VSS
A32 VSS VSS
A33 VSS VSS
A4 VSS VSS
A7 VSS VSS
A8 VSS VSS
AC1 VSS VSS
AC35 VSS VSS
AH1 VSS VSS
AH35 VSS VSS
AJ1 VSS VSS
AJ35 VSS VSS
AM1 VSS VSS
AM2 VSS VSS
AM3 VSS VSS
AM33 VSS VSS
AM34 VSS VSS
AM35 VSS VSS
AN1 VSS VSS
AN2 VSS VSS
AN32 VSS VSS
AN34 VSS VSS
AN35 VSS VSS
AN4 VSS VSS
AP3 VSS VSS
AP32 VSS VSS
AP33 VSS VSS
AP4 VSS VSS
AR13 VSS VSS
AR16 VSS VSS
AR20 VSS VSS
AR23 VSS VSS
AR28 VSS VSS
AR29 VSS VSS
AR3 VSS VSS
AR32 VSS VSS
AR33 VSS VSS
AR4 VSS VSS
AR7 VSS VSS
AR8 VSS VSS
Pin OR3T125
Pad Function
B3 VSS VSS
B32 VSS VSS
B33 VSS VSS
B4 VSS VSS
C1 VSS VSS
C2 VSS VSS
C32 VSS VSS
C34 VSS VSS
C35 VSS VSS
C4 VSS VSS
D1 VSS VSS
D2 VSS VSS
D3 VSS VSS
D33 VSS VSS
D34 VSS VSS
D35 VSS VSS
G1 VSS VSS
G35 VSS VSS
H1 VSS VSS
H35 VSS VSS
N1 VSS VSS
N35 VSS VSS
T1 VSS VSS
T35 VSS VSS
Y1 VSS VSS
Y35 VSS VSS
A1 VDD VDD
A17 VDD VDD
A18 VDD VDD
A2 VDD VDD
A30 VDD VDD
A31 VDD VDD
A34 VDD VDD
A35 VDD VDD
A5 VDD VDD
A6 VDD VDD
AE31 VDD VDD
AE5 VDD VDD
AK1 VDD VDD
AK35 VDD VDD
AL1 VDD VDD
AL11 VDD VDD
AL16 VDD VDD
AL20 VDD VDD
AL25 VDD VDD
AL31 VDD VDD
Pin OR3T125
Pad Function
Pin Information
(
continued
)
Table 75. OR3T125 600-Pin EBGA Pinout
(
continued
)
Lucent Technologies Inc. 193
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
AL35 VDD VDD
AL5 VDD VDD
AM32 VDD VDD
AM4 VDD VDD
AN3 VDD VDD
AN33 VDD VDD
AP1 VDD VDD
AP2 VDD VDD
AP34 VDD VDD
AP35 VDD VDD
AR1 VDD VDD
AR18 VDD VDD
AR19 VDD VDD
AR2 VDD VDD
AR30 VDD VDD
AR31 VDD VDD
AR34 VDD VDD
AR35 VDD VDD
AR5 VDD VDD
AR6 VDD VDD
B1 VDD VDD
B2 VDD VDD
B34 VDD VDD
B35 VDD VDD
Pin OR3T125
Pad Function
C3 VDD VDD
C33 VDD VDD
D32 VDD VDD
D4 VDD VDD
E1 VDD VDD
E11 VDD VDD
E16 VDD VDD
E20 VDD VDD
E25 VDD VDD
E31 VDD VDD
E35 VDD VDD
E5 VDD VDD
F1 VDD VDD
F35 VDD VDD
L31 VDD VDD
L5 VDD VDD
T31 VDD VDD
T5 VDD VDD
U35 VDD VDD
V1 VDD VDD
V35 VDD VDD
W1 VDD VDD
Y31 VDD VDD
Y5 VDD VDD
Pin OR3T125
Pad Function
Pin Information
(
continued
)
Table 75. OR3T125 600-Pin EBGA Pinout
(
continued
)
194194 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Package Thermal Characteristics
There are four thermal parameters that are in common
use: ΘJA, ψJC, ΘJC, and ΘJB. It should be noted that all
the parameters are affected, to varying degrees, by
package design (including paddle size) and choice of
materials, the amount of copper in the test board or
system board, and system airflow.
The data base containing the thermal values for all of
Lucent Technologies’ IC packages is currently being
updated to conform to modern JEDEC standards.
Thus, Table 76 contains the currently availab le thermal
specifications for Lucent Technologies’ FPGA pack-
ages mounted on both JEDEC and non-JEDEC test
boards. The thermal values for the newer package
types correspond to those packages mounted on a
JEDEC four-layer board. The values for the older pack-
ages, howe ver , correspond to those packages mounted
on a non-JEDEC, single-layer, sparse copper board
(see Note 2). It should also be noted that the v alues for
the older packages are considered conservative.
ΘJA
This is the thermal resistance from junction to ambient
(a.k.a. theta-JA, R-theta, etc.).
where TJ is the junction temperature, TA is the ambient
air temperature, and Q is the chip power.
Experimentally, ΘJA is determined when a special ther-
mal test die is assembled into the pack age of interest,
and the part is mounted on the thermal test board. The
diodes on the test chip are separately calibrated in an
oven. The package/board is placed either in a JEDEC
natural convection box or in the wind tunnel, the latter
for forced convection measurements. A controlled
amount of power (Q) is dissipated in the test chip’s
heater resistor, the chip’s temperature (TJ) is deter-
mined by the f orward drop on the diodes, and the ambi-
ent temperature (TA) is noted. Note that ΘJA is
expressed in units of °C/watt.
ψJC
This JEDEC designated parameter correlates the junc-
tion temperature to the case temperature. It is generally
used to infer the junction temperature while the device
is operating in the system. It is not considered a true
thermal resistance, and it is defined by:
where TC is the case temperature at top dead center,
TJ is the junction temperature, and Q is the chip power .
During the ΘJA measurements described above,
besides the other parameters measured, an additional
temperature reading, TC, is made with a thermocouple
attached at top-dead-center of the case. ψJC is also
expressed in units of °C/watt.
ΘJC
This is the thermal resistance from junction to case. It
is most often used when attaching a heat sink to the
top of the package. It is defined by:
The parameters in this equation have been defined
above. Howe ver , the measurements are performed with
the case of the part pressed against a water-cooled
heat sink so as to draw most of the heat generated by
the chip out the top of the package. It is this difference
in the measurement process that diff erentiates ΘJC
from ψJC. ΘJC is a true thermal resistance and is
expressed in units of °C/watt.
ΘJB
This is the thermal resistance from junction to board
(a.k.a. ΘJL). It is defined by:
where TB is the temperature of the board adjacent to a
lead measured with a thermocouple. The other param-
eters on the right-hand side have been defined above.
This is considered a true thermal resistance, and the
measurement is made with a water-cooled heat sink
pressed against the board so as to dra w most of the
heat out of the leads. Note that ΘJB is expressed in
units of °C/watt, and that this parameter and the way it
is measured is still in JEDEC committee.
ΘJA TJTA
–
Q
--------------------
=
ψJC TJTC
–
Q
--------------------
=
ΘJC TJTC
–
Q
--------------------
=
ΘJB TJTB
–
Q
------------------
=
Lucent Technologies Inc. 195
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Package Thermal Characteristics (continued)
FPGA Maximum Junction Temperature
Once the power dissipated by the FPGA has been determined (see the Estimating Power Dissipation section), the
maximum junction temperature of the FPGA can be found. This is needed to determine if speed derating of the
device from the 85 °C junction temperature used in all of the delay tables is needed. Using the maximum ambient
temperature, TAmax, and the power dissipated by the device, Q (expressed in °C), the maximum junction tempera-
ture is approximated by:
TJmax = TAmax + (Q • ΘJA)
Table 76 lists the plastic package thermal characteristics for the
ORCA
Series FPGAs.
Table 76. Plastic Package Thermal Characteristics for the
ORCA
Series1
1. Mounted on 4-layer JEDEC standard test board with two power/ground planes.
2. With thermal balls connected to board ground plane.
3. Without thermal balls connected to board ground plane.
Package ΘJA (°C/W) TA = 70 °C max
TJ = 125 °C max
@ 0 fpm (W)
0 fpm 200 fpm 500 fpm
208-Pin SQ FP126.5 23.0 21.0 2.1
208-P in SQFP2112.8 10.3 9.1 4.3
240-Pin SQ FP125.5 22.5 21.0 2.2
240-P in SQFP2113.0 10.0 9.0 4.2
256-P in PB G A1, 2 22.5 19.0 17.5 2.4
256-P in PB GA1, 3 26.0 22.0 20.5 2.1
352-P in PB GA1, 2 19.0 16.0 15.0 2.9
352-P in PB GA1, 3 25.5 22.0 20.5 2.1
432-P in EB GA111.0 8.5 7.5 5.0
600-P in EB G A111.0 8.5 7.5 5.5
196196 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Package Coplanarity
The coplanarity limits of the
ORCA
Series 3 packages
are as follows.
Table 77. Package Coplanarity
Package Parasitics
The electrical performance of an IC package, such as
signal quality and noise sensitivity, is directly affected
by the package parasitics. Tab le 78 lists eight parasitics
associated with the
ORCA
packages. These parasitics
represent the contributions of all components of a
package, which include the bond wires, all internal
package routing, and the external leads.
Four inductances in nH are listed: LSW and LSL, the
self-inductance of the lead; and LMW and LML, the
mutual inductance to the nearest neighbor lead. These
parameters are important in determining ground
bounce noise and inductive crosstalk noise. Three
capacitances in pF are listed: CM, the mutual capac i-
tance of the lead to the nearest neighbor lead; and C1
and C2, the total capacitance of the lead to all other
leads (all other leads are assumed to be grounded).
These parameters are important in determining capaci-
tive crosstalk and the capacitive loading effect of the
lead. The lead resistance value, RW, is in MΩ.
The parasitic values in Table 78 are for the circuit
model of bond wire and package lead parasitics. If the
mutual capacitance value is not used in the designer’s
model, then the value listed as mutual capacitance
should be added to each of the C1 and C2 cap ac ito rs.
Package Type Coplanarity Limit
(mils)
EBGA 8.0
PBGA 8.0
SQFP/SQFP2 4.0
3.15
Table 78. Package Parasitics
5-3862(F).a
Figure 104. Package Parasitics
Package Type LSW LMW RWC1C2CMLSL LML
208-Pin SQFP 4 2 200 1 1 1 7—10 4—6
208-Pin SQFP2 4 2 200 1 1 1 6—9 4—6
240-Pin SQFP 4 2 200 1 1 1 8—12 5—8
240-Pin SQFP2 4 2 200 1 1 1 7—11 4—7
256-Pin PBGA 5 2 220 1 1 1 5—8 2—4
352-Pin PBGA 5 2 220 1.5 1.5 1.5 7—12 3—6
432-Pin EBGA 4 1.5 500 1 1 0.3 3—5.5 0.5—1
600-Pin EBGA 4 1.5 500 1 1 0.4 3—6 0.5—1
PAD N BOARD PAD
CM
C1
LSW RWLSL
LMW
C2
C1
LML
C2
PAD N + 1
LSW RWLSL
Lucent Technologies Inc. 197
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Package Outline Diagrams
Terms and Definitions
Basic Size (BSC): The basic size of a dimension is the size from which the limits for that dimension are derived
by the application of the allowance and the tolerance.
Design Size: The design size of a dimension is the actual size of the design, including an allowance for fit
and tolerance.
Typical (TYP): When specified after a dimension, this indicates the repeated design size if a tolerance is
specified or repeated basic size if a tolerance is not specified.
Reference (REF): The ref erence dimension is an untoleranced dimension used for inf ormational purposes only.
It is a repeated dimension or one that can be derived from other values in the drawing.
Minimum (MIN) or
Maximum (MAX): Indicates the minimum or maximum allowable size of a dimension.
198 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Package Outline Diagrams (continued)
208-Pin SQFP
Dimensions are in millimeters.
Note: The dimensions in this outline diagram are intended for informational purposes only.
For detailed schematics to assist your design eff orts, please contact your Lucent Technologies Sales Representative .
156
105
30.60 ± 0.20
157208
1
52
53 104
28.00 ± 0.20
28.00
± 0.20
30.60
± 0.20
PIN #1 IDENTIFIER ZONE
4.10 MAX
0.08
3.40 ± 0.20
SEATING PLA NE
0.25 MIN
0.50 TYP
DETAIL BDETAIL A
0.50/0.75
GAGE PLANE
SEATING PLAN E
1.30 REF
0.25
DETAIL A
DETAIL B
0.17/0.27
0.10 M
0.090/0.200
Lucent Technologies Inc. 199
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Package Outline Diagrams (continued)
208-Pin SQFP2
Dimensions are in millimeters.
DETAIL C (SQFP2 CHIP-UP) 5-3828(F).a
5-3828(F)
CHIP
CHIP BONDED FACE UP
COPPER HEAT SIN K
0.50/0.75
GAGE PLANE
SEATI N G PLA N E
1.30 REF
0.25
DETAIL A
DETAIL B
0.17/0.2
0.10 M
0.090/0.200
156
105
30.60 ± 0.20
157
208
53 104
28.00 ± 0.20
EXPOSE D HEAT SI NK APPEARS ON BO TTO M
SURFACE: CHIP BONDED FACE UP. (SEE DETAIL C.)
28.00
± 0.20
30.60
± 0.20
PIN #1 IDENTIFIER ZONE
21.0
REF
21.0 REF
4.10 MAX
0.08
3.40 ± 0.20
SEATING PLA NE
0.25 MIN
0.50 TYP
DETAIL B
DETAIL A
200 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Package Outline Diagrams (continued)
240-Pin SQFP
Dimensions are in millimeters.
Note: The dimensions in this outline diagram are intended for inf ormational purposes only. For detailed schematics to assist y our design eff orts,
please contact your Lucent Technologies Sales Representative.
0.50/0.75
GAGE PLANE
SEATING PLANE
1.30 REF
0.25
DETAIL A
DETAIL B
0.17/0.27
0.10
M
0.090/0.200
180
121
181240
34.60 ± 0.20
1
32.00 ± 0.20
60
61 120
PIN #1 IDENTIFIER Z ONE
32.00
± 0.20
34.60
± 0.20
0.08
3.40 ± 0.20
S EATIN G PLA NE
0.25 MIN
0.50 TYP
DETAIL A DETAIL B
4.10 MAX
Lucent Technologies Inc. 201
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Package Outline Diagrams (continued)
240-Pin SQFP2
Dimensions are in millimeters.
DETAIL C (SQFP2 CHIP-UP) 5-3825(F).a
0.50/0.75
GAGE PLANE
SEATING PLANE
1.30 REF
0.25
DETAIL A
DETAIL B
0.17/0.27
0.10
M
0.090/0.200
CHIP
CHIP BONDED FACE UP
COPPER HEAT SINK
0.08
3.40 ± 0.20
SEATING PLANE
0.25 MIN
0.50 TYP
DETAIL A DE TAIL B
180
121
181240
34.60 ± 0.20
1
32.00 ± 0.20
60
61 120
PIN #1 IDENTIFIER ZONE
32.00
± 0.20
34.60
± 0.20
EXPOSED HEA T SINK APPEARS ON BOTTOM
SURFACE: CHIP BONDED FACE UP. (SEE DETAIL C.)
24.2
REF
24.2 REF
4.10 MAX
202 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Package Outline Diagrams (continued)
256-Pin PBGA
Dimensions are in millimeters.
5-4406(F)
Note: Although the 16 thermal enhancement balls are stated as an option, they are standard on the 256 FPGA package.
0.36 ± 0.04 1.17 ± 0.05 2.13 ± 0.19
SEATING PLAN E
SOLDER BALL
0.60 ± 0.10
0.20
PWB
MOLD
COMPOUND
27.00 ± 0.20
27.00
± 0.20
24.00 +0.70
–0.00
24.00 +0.70
–0.00
A1 BALL
IDENT IFIER ZONE
A
B
C
D
E
F
G
H
J
K
L
M
Y
N
P
R
T
U
V
W
12345678910
1112131415161718 20
19
CENTER ARRAY
FOR THERM AL
ENHANCEMENT
(OPTIONAL)
19 SPACES @ 1.27 = 24.13
A1 BALL
CORNER
19 SPACES
@ 1.27 = 24.13
0.75 ± 0.15
(SEE NOTE BELOW)
Lucent Technologies Inc. 203
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Package Outline Diagrams (continued)
352-Pin PBGA
Dimensions are in millimeters.
5-4407(F)
Note: Although the 36 thermal enhancement balls are stated as an option, they are standard on the 352 FPGA package.
0.56 ± 0.06 1.17 ± 0.05 2.33 ± 0.21
SEATING PLANE
SOLDER BALL
0.60 ± 0.10 0.20
PWB
MOLD
COMPOUND
35.00
+0.70
–0.00
30.00
A1 BALL
IDENTIFIE R ZONE
AF
AE
AD
AC
AB
AA
Y
W
V
U
T
R
G
25 SPACES @ 1.27 = 31.75
P
N
M
L
K
J
H
1 2 3 4 5 6 7 8 9 10 12 14 16 18 22 24 2620
11 13 15 17 2119 23 25
F
E
D
C
B
A
CENTER ARRAY
25 SPACES
A1 BALL
0.75 ± 0.15
35.00 ± 0.2 0
30.00 +0.70
–0.00
± 0.20
@ 1.27 = 31.75
FOR THERMAL
ENHANCEMENT
(OPTIONAL)
CORNER
(SEE NOTE BELOW)
204 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Package Outline Diagrams (continued)
432-Pin EBGA
Dimensions are in millimeters.
5-4409(F)
0.91 ± 0.06 1.54 ± 0.13
SEATING PLANE
SOLDER BALL
0.63 ± 0.07
0.20
40.00 ± 0.10
40.00
A1 BALL
M
D
AG
B
F
K
HG
E
AD
L
T
J
N
AJ
C
Y
P
AH
AE
AC
AA
W
U
R
AK
AF
AB
V
AL
A
19 3026
528242223 25720 312915 21
18
32711 17
4 6 81012141629131
30 SPACES @ 1.27 = 38.10
30 SPACES
A1 BALL
0.75 ± 0.15
IDEN TI FIER ZONE
± 0.10
@ 1.27 = 38.10
CORNER
Lucent Technologies Inc. 205
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Package Outline Diagrams (continued)
600-Pin EBGA
Dimensions are in millimeters.
5-4408(F)
0.91 ± 0.06 1.54 ± 0.13
SEATING PLA NE
SOLDER BALL
0.63 ± 0.07
0.20
45.00 ± 0.10
45.00
A1 BALL
T
D
H
AL
F
K
B
P
ML
J
AH
R
C
E
Y
N
U
AN
G
AD
V
AM
AJ
AG
AE
AC
AA
W
AP
AK
AF
AB
AR
A
19 3026 2824 322220184 6 81012 1416234
523257312915 2132711 1791313533
34 SPACES @ 1.27 = 43.18
34 SP ACES
A1 BALL
0.75 ± 0.15
IDENTI FIER ZONE
± 0.10
@ 1.27 = 43.18
CORNER
206 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Ordering Information
OR3C80, -4 Speed Grade, 240-pin Power Quad Shrink Flat Package (SQFP2), Commercial Temperature
Table 79. Voltage Options
Table 80. Temperature Options
Table 81. Package Options
Table 82.
ORCA
Series 3
Package Matrix
Key: C = commercial, I = industrial.
Table 83. Speed Grade Options
Device Voltage
OR3Cxx 5.0 V
OR3Txxx 3.3 V
Symbol Description Temperature
(Blank) Commercial 0 °C to 70 °C
I Industrial –40 °C to +85 °C
Symbol Description
BA Plastic Ball Grid Array (PBGA)
BC Enhanced Ball Grid Array (EBGA)
PS Power Quad Shrink Flat Package (SQFP2)
S Shrink Quad Flat Package (SQFP)
Packages 208-Pin
EIAJ SQFP 208-Pin
EIAJ/SQFP2 240-Pin
EIAJ SQFP 240-Pin
EIAJ/SQFP2 256-Pin
PBGA 352-Pin
PBGA 432-Pin
EBGA 600-Pin
EBGA
S208 PS208 S240 PS240 BA256 BA352 BC432 BC600
OR3T20 Cl — CI —CI
CI ——
OR3T30 CI —CI —CI
CI ——
OR3C/T55 — CI —CI CI CI ——
OR3C/T80 — CI —CI —CI CI —
OR3T125 — CI —CI —CICICI
Device Speed Grade
OR3Cxx -4, -5
OR3Txxx -5, -6, -7
OR3C80-4 PS 240
DEVICE TYPE
SPEED GRADE PACKA GE TYPE
NUMB ER O F PINS
TEMPERATURE RANGE
Example:
Lucent Technologies Inc. 207
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Index
A
Absolute Maximum Ratings, 96
AND-OR-INVERT (AOI), 6
AND-OR -I NV ER T (A O I) ,1
(see also Supplemental Logic
Interconnect Cell (SLIC), 1
Architecture
Overview, 6—9
ASWE, 9, 11, 15—17, 23, 33, 48
B
Bidirecti on al Buf f ers (BIDIs ) , 6, 19, 43, 83
(see also Routingand SLIC)
Bit Stream (see FPGA Configuration)
Bit Stream Error Checking, 88
(see also FPGA states of Operation)
Bound ary Sc an, 55
(see Special Function Blocks)
C
Clock Control (CLKCNTRL), 50
(see also Clock Distribution Network and
Special Function Blocks)
Clock Distribution Network, 48–51
CLKCNTRL, 50
ExpressCLK, 48
Inputs, 51
Fast Clock, 48, 51
Global Control Signals, 48
In the PICs
ExpressCLK, 50
System Clock, 50
In the PLC Array
Fast Clock, 49
System Clock, 49
PFU Clock Sources, 48
Selecting Clock Input Pins, 51
System Clock, 48
To the PLC Array
Fast Clock, 50
System Clock, 50
Clock Enable (CE), 9, 11, 17, 23, 31, 48
Clock Multiplication (see PCM)
Comparator (see LUT Operating Modes)
Configuration (see FPGA States of Operation
or FPGA Configuration)
Control Inputs (see PICs, Inputs)
D
Demultiplexing (see PICs, Input Demultiplexing), 38
Duty-Cycle Adjustment (see PCM)
E
Electrical Characteristics, 97, 98
Error Check ing (s ee FPGA Confi gu ra tio n)
ExpressCLK, 1, 6, 31, 34, 37, 39, 41, 43, 47—51,
70—74, 77—81
(see also Clock distribution Network and
Programmable Clock Manager)
F
Fast Clock, 46—51, 54
(see Clock Distribution Network)
5 V Tolerant I/O 35
Flexible Input Structure (FINS) 1, 27, 32
(see also Routi ng)
FPGA Configuration, 87—94
Configuration Frame Format, 87
Configur ati on Mode s, 89
Asynchronous Peripheral Mode, 91
Daisy-Chaining, 95
Master Parallel Mode, 89
Master Seri al Mod e, 90
Microprocessor Interface (MPI) Mode, 91
Slave Parallel Mode, 94
Slave Serial Mode, 94
Data Format, 86
Data Frame, 86
Using
ORCA
Foundry to Generate RAM Data, 86
FPGA States of Operation
Configur ati on, 83
Initialization, 82
Other Configuration Options, 85
Partial Reconfiguration, 85
Reconfiguration, 85
Start-Up, 84
I
IEEE
Standard, 1149.1 55, 59
Initialization (see FPGA States of Operation)
Input/Output Buffers
Measurement Conditions, 138
Output Buffer Characteristics
OR3Cxx, 139
OR3Txxx, 141
J
JTAG (see Boundry Scan)
208208 Lucent Technologies Inc.
Data Sheet
June 1999
ORCA
Series 3C and 3T FPGAs
Index (continued)
L
Look-Up Table (LUT) Operating Modes, 11—18
Adder-Subtractor Submode, 15
Counter Submode, 15
Equality Comparators, 16
Half-Logic Mode, 14
Logic Mode, 12
Memory Mode, 17
Multiplier Submode, 16
Ripple Mode, 14
LSR, 11, 17, 23—24, 31, 48
M
Maximum Ratings (see Absolute Maximum Ratings)
Microprocessor Interface (MPI), 62—69
i960
System, 64
Interface to FPGA, 65
PowerPC
System, 63
Setup and Contro l Regis te rs, 66
Multiplexing (see Output Multiplexing)
Multiplier (see LUT Operating Modes)
O
ORCA
Foundry Development System, 25
Overview, 7
Ordering Information
Package Matrix, 207
Package Options, 207
Temperature Options, 207
Voltage Options, 207
Output (see PICs)
Output Multiplexing, 39
P
Package Information, 200—206
Package Matrix, 204
Package Outline Diagrams, 200
208-Pin SQFP2, 199
240-Pin SQFP2, 202
256-Pin PBGA, 203
352-Pin PBGA, 204
432-Pin EBGA, 205
600-Pin EBGA, 206
Terms and Definitions, 200
PAL
, 1 (see also Supplemental Logic and
Interconnect Cell (SLIC)) 1
PIC Routing (see Routing)
Pin Information
208-Pin SQFP2 Pinout, 151
240-Pin SQFP2 Pinout, 156
256-Pin PBGA Pinout, 162
352-Pin PBGA Pinout, 165
432-Pin EBGA Pinout, 177
600-Pin EBGA Pinout, 184
Package Compatibility, 152
Pin Descriptions 147, 151
Power Dissip ati on, 144
5 V Tolerant I/O, 143
OR3Cxx, 144
OR3Txxx, 145
PowerPC
(see Microprocessor Interface)
Programmable Clock Manager (PCM), 6, 81
Clock Delay, 74
Clock Multiplication, 75
DLL Mode, 73
PCM Cautions, 81
PCM Detailed Programming, 77
PCM Operation, 76
PCM/FPGA Internal Interface, 76
PLL Mode, 74
Regist ers, 71
Programmable Function Unit (PFU), 9
Cintrol Inputs, 11
Operating Modes, 11
Softwired LUTs (SWL), 12
Twin-quad Architecture, 1, 8, 14, 19
Programmable Input/Output Cells (PICs), 34—44
5 V Tolerant I/O, 35
Architecture, 43
Control Inputs, 11, 23
ASWE , 11
CE, 11
CLK, 11
GSRN, 11, 24
LSR, 11
SEL, 11
Input Demultiplexing, 38
Inputs, 36
Output Multiplexing, 39
Outputs, 39
Open-Drain Output Option, 39
Propagation Delays, 39
Overview, 32
PIO, 34
PIO Logic , 41
PIO Options, 35
PIO Register Control Signals, 41
Zero-Hold Input, 37
Programmable Logic Cells (PLCs), 9—33
Architecture, 32
Latches/Flip-Flops, 23, 24
PFU, 9
Propagation Delays (see PICs, Outputs)
Routing, 25
SLIC, 19—22
Lucent Technologies Inc. 209
Data Sheet
J une 1999
ORCA
Series 3C and 3T FPGAs
Index (continued)
R
RAM (see also FPGA Configuration), 85
Dual-port, 3, 10, 17
Single-port, 3, 10, 17
Recommen ded Op er ati ng Cond itions , 95
Reconfiguration (see FPGA States of Operation)
Routing
3-Statab le Bi dir ec ti ona l Buff er s, 24
BIDI Routing, 24, 27
Clock (and Global CE and LSR) Routing, 30
Configurable Interconnect Points (CIPs), 24
Control Signal and Fast-Carry Routing, 27
Flexible Input Structure (FINS), 26
Inter-PLC Routing Resources, 28
Interquad Routing, 44
Intra-PLC Routing Resources, 26—27
Minimizing Routing Delay, 30
Overview, 5
PFU Output Switching, 26
PIC Routing, 41—4 3
PIC Interquad (MID) Routing, 46
PLC Routing, 26—32
Programmable Corner Cell Routing, 45
SLIC Connectivity, 27
Switching Routing Segments (xSW), 26
S
SEL, 8, 10, 22
Softwired LUTs (SWLs),1, 6, 11, 12
(see also Look-Up Table Operating Modes)
Special Function Blocks
Bound ary Sc an, 60
Boundary-Scan Cells, 59
Boundary-Scan Timing, 60
Microprocessor Interface (MPI), 61—68
Programmable Clock Manager (PCM), 69—80
Single Function Blocks, 51
Clock Control (CLKCNTRL), 53
Global 3-State Control (TS_ALL), 52
Global Set/Reset (GSRN), 52
Internal Oscillator, 52
Readback Logic, 51
Start-Up Logic, 53
Start-Up (see FPGA States of Operation)
StopCLK, 1, 5, 53
(see also Special Function Blocks)
Subtractor (see LUT Operating Modes)
Supplemental Logic and Interconnect Cell (SLIC), 1,
18—21
System Clock (see Clock Distribution Network), 47
3-state, 3—4, 17—18, 34, 38, 45—46, 52, 56, 59, 82, 84
T
Timing Characteristics
Asynchronous Peripheral Configuration Mode, 132
Boundry-Scan Timing, 119
Clock Timing, 119
Derating, 98
Description, 98
General Configuration Mode Timing, 129, 130
Master Paral le l Confi guration Mode, 131
Master Seri al Conf igu ra tio n Mode, 130
Microprocessor Interface Configuration Timing, 137
PFU Timing, 100
PIO Timing, 108, 109, 110
PLC Timing, 107
Programmable Clock Manager Timing, 115
Readback Timing, 139
Slave Parallel Configuration Mode, 134
Slave Serial Configuration Mode, 133
SLIC Timing, 107
Tolerant I/O (see 5 V Tolerant I/O), 34
TS_ALL, 52 Twin-quad Architecture (see PFU), 1
U—Z
Zero-hold Inputs, 34—36
Lucent Technologies Inc. reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent
accompany the sale of any such product(s) or information.
ORCA
is a registered trademark of Lucent Technologies Inc. Foundry is a trademark of Xilinx, Inc.
Copyright © 1999 Lucent Technologies Inc.
All Rights Reserved
Printed in U.S.A.
June 1999
DS99-087FPGA (Replaces DS98-163FPGA -01)
For additional information, contact your Microelectronics Group Account Manager or the following:
INTERNET: http://www.lucent.com/micro, or for FPGA information, http://www.lucent.com/orca
E-MAIL: docmaster@micro.lucent.com
N. AMERICA: Microelectronics Gro up, Lucent Technologies Inc., 555 Uni on Boulevard, Room 30L-15P-BA, Allentown, PA 1 81 03
1-800-372-2447, FAX 610 - 712-4106 (In CANADA: 1-800-553-2448, FAX 610-712-4106)
ASIA PACIFIC: Microelectronics Group, Lucent Technologie s Singapore Pte. Ltd., 77 Science Park Drive, #03-18 Cintech III, Singapore 118256
Tel. (65) 778 8833, FAX (65) 777 7495
CHINA: Microelectronics Group, Lucent Technologies (China) Co., Ltd., A-F2, 23/F, Zao Fong Universe Building, 1800 Zhong Shan Xi Roa d
Shanghai 200233 P. R. China Tel. (86) 21 6440 0468, ext. 316, FAX (86) 21 6440 0652
JAPAN: Microelectronics Group, Lucent Technologies Japan Ltd., 7-18, Higashi-Gotanda 2-chome, Shinagawa-ku, Tokyo 141, Japan
Tel. (81) 3 5421 1600, FAX (81) 3 5421 1700
EUROPE: Data Requests: MICROELECTRONICS GROUP DATALINE: Tel. (44) 7000 582 368, FAX (44) 1189 328 148
Technical Inquir ies: GERMAN Y: (49) 89 95086 0 (Munich), UNITED KIN G DOM: (44) 13 44 865 900 (Ascot),
FRANCE:
(33) 1 40 83 68 00
(Paris), SWEDEN:
(46) 8 594 607 00
(Stockholm), FINLAND:
(358) 9 4354 2800
(Hel si nk i), ITALY :
(39) 02
6608131 (Milan), SPAIN: (34) 1 807 1441 (Madrid)