S-82A1A Series BATTERY PROTECTION IC FOR 1-CELL PACK www.ablic.com Rev.2.4_00 (c) ABLIC Inc., 2016-2019 The S-82A1A Series is a protection IC for lithium-ion / lithium polymer rechargeable batteries and includes high-accuracy voltage detection circuits and delay circuits. It is suitable for protecting 1-cell lithium-ion / lithium polymer rechargeable battery packs from overcharge, overdischarge, and overcurrent. By using an external overcurrent detection resistor, the S-82A1A Series realizes high-accuracy overcurrent protection with less effect from temperature change. Features * High-accuracy voltage detection circuit Overcharge detection voltage 3.5 V to 4.6 V (5 mV step) Accuracy 20 mV Overcharge release voltage 3.1 V to 4.6 V*1 Accuracy 50 mV Overdischarge detection voltage 2.0 V to 3.0 V (10 mV step) Accuracy 50 mV Overdischarge release voltage 2.0 V to 3.4 V*2 Accuracy 100 mV Discharge overcurrent detection voltage 1 0.010 V to 0.100 V (1 mV step) Accuracy 3 mV Discharge overcurrent detection voltage 2 0.030 V to 0.200 V (1 mV step) Accuracy 5 mV Load short-circuiting detection voltage 0.050 V to 0.500 V (5 mV step) Accuracy 20 mV Charge overcurrent detection voltage -0.100 V to -0.010 V (1 mV step) Accuracy 3 mV * Detection delay times are generated only by an internal circuit (external capacitors are unnecessary). * 0 V battery charge: Enabled, inhibited * Power-down function: Available, unavailable * Release condition of discharge overcurrent status: Load disconnection, charger connection * Release voltage of discharge overcurrent status: Discharge overcurrent detection voltage 1 (VDIOV1), discharge overcurrent release voltage (VRIOV) = VDD x 0.8 (typ.) * High-withstand voltage: VM pin and CO pin: Absolute maximum rating 28 V * Wide operation temperature range: Ta = -40C to +85C * Low current consumption During operation: 2.0 A typ., 4.0 A max. (Ta = +25C) During power-down: 50 nA max. (Ta = +25C) During overdischarge: 500 nA max. (Ta = +25C) * Lead-free, Sn 100%, halogen-free*3 P *1. Overcharge release voltage = Overcharge detection voltage - Overcharge hysteresis voltage (Overcharge hysteresis voltage can be selected as 0 V or from a range of 0.1 V to 0.4 V in 50 mV step.) *2. Overdischarge release voltage = Overdischarge detection voltage + Overdischarge hysteresis voltage (Overdischarge hysteresis voltage can be selected as 0 V or from a range of 0.1 V to 0.7 V in 100 mV step.) *3. Refer to " Product Name Structure" for details. Applications * Lithium-ion rechargeable battery pack * Lithium polymer rechargeable battery pack Packages * SNT-6A * DFN-6(1414)A 1 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Block Diagram VDD Overdischarge detection comparator DO Overcharge detection comparator VSS Discharge overcurrent detection 1 comparator Control logic Discharge overcurrent detection 2 comparator Delay circuit Oscillator Load short-circuiting detection comparator VINI Charge overcurrent detection comparator VM Figure 1 2 CO BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Product Name Structure 1. Product name 1. 1 SNT-6A S-82A1A xx - I6T1 U Environmental code U: Lead-free (Sn 100%), halogen-free Package abbreviation and IC packing specifications*1 I6T1: SNT-6A, Tape Serial code*2 Sequentially set from AA to ZZ *1. Refer to the tape drawing. *2. Refer to "3. Product name list". 1. 2 DFN-6(1414)A S-82A1A xx - A6T5 S Environmental code S: Lead-free, halogen-free Package abbreviation and IC packing specifications*1 A6T5: DFN-6(1414)A, Tape Serial code*2 Sequentially set from AA to ZZ *1. Refer to the tape drawing. *2. Refer to "3. Product name list". 2. Packages Table 1 Package Drawing Codes Package Name SNT-6A DFN-6(1414)A Dimension PG006-A-P-SD PV006-A-P-SD Tape PG006-A-C-SD PV006-A-C-SD Reel PG006-A-R-SD PV006-A-R-SD Land PG006-A-L-SD PV006-A-L-SD 3 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 3. Product name list 3. 1 SNT-6A Table 2 (1 / 2) Product Name Discharge Overcharge Overcharge Overdischarge Overdischarge Overcurrent Detection Release Detection Release Detection Voltage Voltage Voltage Voltage Voltage 1 [VCU] [VCL] [VDL] [VDU] [VDIOV1] Discharge Overcurrent Detection Voltage 2 [VDIOV2] Load Shortcircuiting Detection Voltage [VSHORT] Charge Overcurrent Detection Voltage [VCIOV] S-82A1AAB-I6T1U 4.470 V 4.270 V 2.500 V 2.800 V 0.048 V - 0.140 V -0.031 V S-82A1AAC-I6T1U 4.425 V 4.225 V 2.800 V 3.000 V 0.034 V - 0.180 V -0.022 V S-82A1AAD-I6T1U 4.425 V 4.225 V 2.800 V 3.000 V 0.040 V - 0.180 V -0.030 V S-82A1AAE-I6T1U 4.475 V 4.275 V 2.500 V 2.900 V 0.036 V - 0.060 V -0.020 V S-82A1AAF-I6T1U 4.425 V 4.225 V 2.400 V 2.800 V 0.034 V - 0.180 V -0.023 V S-82A1AAG-I6T1U 4.230 V 4.130 V 2.800 V 3.000 V 0.050 V - 0.150 V -0.030 V S-82A1AAH-I6T1U 4.500 V 4.300 V 2.300 V 2.700 V 0.065 V - 0.300 V -0.065 V S-82A1AAI-I6T1U 4.425 V 4.225 V 2.600 V 2.600 V 0.030 V 0.045 V 0.150 V -0.025 V S-82A1AAJ-I6T1U 4.425 V 4.225 V 2.600 V 2.900 V 0.030 V - 0.180 V -0.031 V S-82A1AAK-I6T1U 4.425 V 4.225 V 2.800 V 3.000 V 0.040 V - 0.180 V -0.030 V S-82A1AAL-I6T1U 4.425 V 4.225 V 2.800 V 3.000 V 0.040 V - 0.150 V -0.030 V S-82A1AAM-I6T1U 4.475 V 4.275 V 2.800 V 3.000 V 0.040 V - 0.180 V -0.030 V S-82A1AAN-I6T1U 4.425 V 4.225 V 2.600 V 2.800 V 0.040 V - 0.180 V -0.030 V S-82A1AAO-I6T1U 4.425 V 4.225 V 2.500 V 2.900 V 0.036 V - 0.060 V -0.020 V S-82A1AAP-I6T1U 4.475 V 4.275 V 2.400 V 2.800 V 0.025 V - 0.075 V -0.025 V S-82A1AAQ-I6T1U 4.485 V 4.285 V 2.300 V 2.500 V 0.025 V 0.034 V 0.500 V -0.020 V S-82A1AAR-I6T1U 4.475 V 4.275 V 2.500 V 2.900 V 0.032 V - 0.060 V -0.020 V S-82A1AAS-I6T1U 4.425 V 4.225 V 2.600 V 2.800 V 0.030 V 0.045 V 0.150 V -0.025 V S-82A1AAT-I6T1U 4.425 V 4.225 V 2.600 V 2.800 V 0.030 V 0.045 V 0.250 V -0.025 V S-82A1AAU-I6T1U 4.520 V 4.320 V 2.300 V 2.700 V 0.036 V - 0.100 V -0.030 V S-82A1AAV-I6T1U 4.470 V 4.270 V 2.500 V 2.900 V 0.035 V - 0.100 V -0.030 V S-82A1AAW-I6T1U 4.520 V 4.320 V 2.300 V 2.700 V 0.021 V - 0.070 V -0.021 V S-82A1AAX-I6T1U 4.475 V 4.275 V 2.600 V 3.000 V 0.021 V - 0.050 V -0.021 V S-82A1AAY-I6T1U 4.520 V 4.270 V 2.400 V 2.800 V 0.036 V - 0.100 V -0.030 V S-82A1AAZ-I6T1U 4.520 V 4.270 V 2.400 V 2.800 V 0.036 V - 0.100 V -0.030 V S-82A1ABM-I6T1U 4.475 V 4.275 V 2.500 V 2.900 V 0.021 V - 0.080 V -0.027 V S-82A1ABN-I6T1U 4.520 V 4.320 V 2.100 V 2.300 V 0.021 V - 0.100 V -0.033 V S-82A1ABR-I6T1U 4.475 V 4.275 V 2.500 V 2.800 V 0.010 V - 0.035 V -0.013 V S-82A1ABT-I6T1U 3.750 V 3.600 V 2.400 V 2.600 V 0.040 V - 0.060 V -0.040 V S-82A1ABW-I6T1U 4.250 V 4.050 V 2.500 V 2.900 V 0.040 V - 0.100 V -0.040 V S-82A1ABX-I6T1U 4.425 V 4.225 V 3.000 V 3.200 V 0.010 V - 0.050 V -0.010 V S-82A1ABY-I6T1U 4.500 V 4.300 V 2.500 V 2.700 V 0.010 V - 0.060 V -0.010 V S-82A1ACA-I6T1U S-82A1ACH-I6T1U 4.425 V 4.275 V 4.225 V 4.275 V 3.000 V 2.300 V 3.200 V 2.300 V 0.030 V 0.035 V - - 0.060 V 0.060 V -0.030 V -0.025 V 4 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Table 2 (2 / 2) Product Name Delay Time Combination*1 0 V Battery Charge*2 Power-down Function*3 Release Condition Release Voltage of Discharge of Discharge Overcurrent Status*4 Overcurrent Status*5 Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VDIOV1 Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VDIOV1 Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV S-82A1AAB-I6T1U Enabled Unavailable (1) S-82A1AAC-I6T1U Inhibited Unavailable (2) S-82A1AAD-I6T1U Inhibited Unavailable (2) S-82A1AAE-I6T1U Enabled Unavailable (3) S-82A1AAF-I6T1U Inhibited Unavailable (2) S-82A1AAG-I6T1U Inhibited Unavailable (2) S-82A1AAH-I6T1U Enabled Unavailable (4) Inhibited Available S-82A1AAI-I6T1U (5) Inhibited Unavailable S-82A1AAJ-I6T1U (2) Enabled Unavailable S-82A1AAK-I6T1U (2) Inhibited S-82A1AAL-I6T1U (2) Unavailable Inhibited S-82A1AAM-I6T1U (2) Unavailable Inhibited S-82A1AAN-I6T1U (2) Unavailable Enabled S-82A1AAO-I6T1U (3) Unavailable Enabled S-82A1AAP-I6T1U (1) Unavailable Inhibited S-82A1AAQ-I6T1U (6) Unavailable Inhibited S-82A1AAR-I6T1U (3) Unavailable Inhibited S-82A1AAS-I6T1U (5) Available Inhibited S-82A1AAT-I6T1U (7) Unavailable Enabled S-82A1AAU-I6T1U (8) Unavailable Enabled S-82A1AAV-I6T1U (9) Unavailable Enabled S-82A1AAW-I6T1U (8) Unavailable Enabled S-82A1AAX-I6T1U (3) Unavailable Enabled S-82A1AAY-I6T1U (10) Unavailable Inhibited S-82A1AAZ-I6T1U (10) Unavailable Enabled S-82A1ABM-I6T1U (12) Unavailable Enabled S-82A1ABN-I6T1U (13) Unavailable Inhibited S-82A1ABR-I6T1U (9) Unavailable Inhibited S-82A1ABT-I6T1U (14) Available Inhibited S-82A1ABW-I6T1U (16) Available Enabled S-82A1ABX-I6T1U (3) Available Enabled S-82A1ABY-I6T1U (8) Available Enabled S-82A1ACA-I6T1U (17) Available Inhibited S-82A1ACH-I6T1U (19) Available *1. Refer to Table 4 about the details of the delay time combinations. *2. 0 V battery charge: Enabled, inhibited *3. Power-down function: Available, unavailable *4. Release condition of discharge overcurrent status: Load disconnection, charger connection *5. Release voltage of discharge overcurrent status: VDIOV1, VRIOV = VDD x 0.8 (typ.) Remark Please contact our sales representatives for products other than the above. 5 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 3. 2 DFN-6(1414)A Table 3 (1 / 2) Product Name Discharge Overcharge Overcharge Overdischarge Overdischarge Overcurrent Detection Release Detection Release Detection Voltage Voltage Voltage Voltage Voltage 1 [VCU] [VCL] [VDL] [VDU] [VDIOV1] Discharge Overcurrent Detection Voltage 2 [VDIOV2] Load Shortcircuiting Detection Voltage [VSHORT] Charge Overcurrent Detection Voltage [VCIOV] S-82A1AAC-A6T5S 4.425 V 4.225 V 2.800 V 3.000 V 0.034 V - 0.180 V -0.022 V S-82A1AAD-A6T5S 4.425 V 4.225 V 2.800 V 3.000 V 0.040 V - 0.180 V -0.030 V S-82A1AAF-A6T5S 4.425 V 4.225 V 2.400 V 2.800 V 0.034 V - 0.180 V -0.023 V S-82A1AAG-A6T5S 4.230 V 4.130 V 2.800 V 3.000 V 0.050 V - 0.150 V -0.030 V S-82A1AAM-A6T5S 4.475 V 4.275 V 2.800 V 3.000 V 0.040 V - 0.180 V -0.030 V S-82A1ABA-A6T5S 4.475 V 4.275 V 2.600 V 3.000 V 0.035 V - 0.075 V -0.035 V S-82A1ABB-A6T5S 4.475 V 4.275 V 2.600 V 3.000 V 0.021 V - 0.050 V -0.021 V S-82A1ABC-A6T5S 4.470 V 4.250 V 2.600 V 2.800 V 0.033 V 0.055 V 0.250 V -0.030 V S-82A1ABD-A6T5S 4.520 V 4.300 V 2.300 V 2.800 V 0.035 V 0.051 V 0.250 V -0.043 V S-82A1ABE-A6T5S 4.475 V 4.225 V 2.600 V 3.000 V 0.030 V - 0.080 V -0.030 V S-82A1ABF-A6T5S 4.475 V 4.225 V 2.600 V 3.000 V 0.040 V - 0.120 V -0.035 V S-82A1ABG-A6T5S 4.425 V 4.225 V 2.400 V 2.900 V 0.014 V - 0.070 V -0.034 V S-82A1ABH-A6T5S 4.425 V 4.225 V 2.600 V 2.900 V 0.030 V - 0.150 V -0.031 V S-82A1ABI-A6T5S 4.425 V 4.225 V 2.600 V 2.800 V 0.030 V 0.045 V 0.150 V -0.025 V S-82A1ABK-A6T5S 4.475 V 4.275 V 2.500 V 2.900 V 0.045 V - 0.130 V -0.034 V S-82A1ABL-A6T5S 4.475 V 4.275 V 2.600 V 2.900 V 0.040 V - 0.180 V -0.030 V S-82A1ABM-A6T5S 4.475 V 4.275 V 2.500 V 2.900 V 0.021 V - 0.080 V -0.027 V 0.100 V -0.033 V S-82A1ABN-A6T5S 4.520 V 4.320 V 2.100 V 2.300 V 0.021 V - S-82A1ABO-A6T5S 4.475 V 4.275 V 2.800 V 3.000 V 0.010 V - 0.050 V -0.010 V S-82A1ABP-A6T5S 4.475 V 4.275 V 2.800 V 3.000 V 0.010 V - 0.050 V -0.014 V S-82A1ABQ-A6T5S 4.475 V 4.275 V 2.800 V 3.000 V 0.034 V - 0.100 V -0.025 V S-82A1ABV-A6T5S 4.275 V 4.175 V 2.600 V 2.800 V 0.040 V 0.050 V 0.200 V -0.040 V S-82A1ACE-A6T5S 4.550 V 4.350 V 2.600 V 3.000 V 0.040 V - 0.180 V -0.040 V S-82A1ACF-A6T5S 4.275 V 4.175 V 2.900 V 3.000 V 0.040 V 0.050 V 0.200 V -0.040 V S-82A1ACG-A6T5S 4.475 V 4.275 V 2.800 V 3.000 V 0.017 V 0.030 V 0.050 V -0.017 V 6 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Table 3 (2 / 2) Product Name Delay Time Combination*1 0 V Battery Charge*2 Power-down Function*3 Release Condition Release Voltage of Discharge of Discharge Overcurrent Status*4 Overcurrent Status*5 Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VDIOV1 Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Load disconnection VRIOV Charger connection VDIOV1 Load disconnection VRIOV Charger connection VDIOV1 Load disconnection VRIOV Inhibited Unavailable S-82A1AAC-A6T5S (2) Inhibited Unavailable S-82A1AAD-A6T5S (2) Inhibited Unavailable S-82A1AAF-A6T5S (2) Inhibited Unavailable S-82A1AAG-A6T5S (2) Inhibited S-82A1AAM-A6T5S (2) Unavailable Enabled Unavailable S-82A1ABA-A6T5S (9) Enabled Unavailable S-82A1ABB-A6T5S (9) Inhibited Unavailable S-82A1ABC-A6T5S (5) Inhibited Unavailable S-82A1ABD-A6T5S (11) Enabled Unavailable S-82A1ABE-A6T5S (2) Enabled Unavailable S-82A1ABF-A6T5S (2) Inhibited S-82A1ABG-A6T5S (2) Unavailable Inhibited S-82A1ABH-A6T5S (2) Unavailable Enabled S-82A1ABI-A6T5S (5) Available Inhibited S-82A1ABK-A6T5S (9) Unavailable Inhibited S-82A1ABL-A6T5S (2) Unavailable Enabled S-82A1ABM-A6T5S (12) Unavailable Enabled S-82A1ABN-A6T5S (13) Unavailable Enabled S-82A1ABO-A6T5S (9) Unavailable Enabled S-82A1ABP-A6T5S (9) Unavailable Enabled S-82A1ABQ-A6T5S (3) Unavailable Inhibited S-82A1ABV-A6T5S (15) Available Inhibited Unavailable S-82A1ACE-A6T5S (2) Inhibited Available S-82A1ACF-A6T5S (15) Inhibited Unavailable S-82A1ACG-A6T5S (18) *1. Refer to Table 4 about the details of the delay time combinations. *2. 0 V battery charge: Enabled, inhibited *3. Power-down function: Available, unavailable *4. Release condition of discharge overcurrent status: Load disconnection, charger connection *5. Release voltage of discharge overcurrent status: VDIOV1, VRIOV = VDD x 0.8 (typ.) Remark Please contact our sales representatives for products other than the above. 7 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Table 4 Delay Time Combination Overcharge Detection Delay Time [tCU] Overdischarge Detection Delay Time [tDL] Discharge Overcurrent Detection Delay Time 1 [tDIOV1] Discharge Overcurrent Detection Delay Time 2 [tDIOV2] Load Shortcircuiting Detection Delay Time [tSHORT] Charge Overcurrent Detection Delay Time [tCIOV] (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) 1.0 s 1.0 s 1.0 s 1.0 s 1.0 s 1.0 s 1.0 s 1.0 s 1.0 s 1.0 s 1.0 s 1.0 s 128 ms 32 ms 64 ms 32 ms 32 ms 64 ms 128 ms 64 ms 64 ms 64 ms 32 ms 64 ms 16 ms 16 ms 16 ms 16 ms 4.0 s 512 ms 4.0 s 32 ms 16 ms 256 ms 2.0 s 256 ms - - - - 280 s 280 s 280 s 530 s 280 s 280 s 280 s 530 s 280 s 530 s 280 s 280 s 8 ms 16 ms 8 ms 16 ms 16 ms 8 ms 8 ms 16 ms 16 ms 16 ms 16 ms 16 ms (13) (14) (15) 1.0 s 1.0 s 512 ms 64 ms 64 ms 64 ms 512 ms 64 ms 8 ms 280 s 280 s 530 s (16) 1.0 s 64 ms 512 ms 16 ms 8 ms 8 ms 8 ms (17) (18) (19) 1.0 s 1.0 s 1.0 s 128 ms 256 ms 64 ms 256 ms 128 ms 8 ms 16 ms 32 ms 16 ms - - - 16 ms - - - 4 ms - 280 s - 280 s 280 s 280 s 16 ms - 8 ms 64 ms 8 ms Remark The delay times can be changed within the range listed in Table 5. For details, please contact our sales representatives. Table 5 Delay Time Overcharge detection delay time Overdischarge detection delay time Discharge overcurrent detection delay time 1 Discharge overcurrent detection delay time 2 Load short-circuiting detection delay time Charge overcurrent detection delay time 8 Symbol Selection Range Remark tCU 256 ms 512 ms 1.0 s - - - tDL 32 ms 64 ms 128 ms 256 ms - - 4 ms 8 ms 16 ms 32 ms 128 ms 256 ms 512 ms 1.0 s 2.0 s 64 ms 4.0 s tDIOV2 4 ms 8 ms 16 ms 32 ms 64 ms 128 ms tSHORT 280 s 530 s - - - - 4 ms 8 ms 16 ms 32 ms 64 ms 128 ms tDIOV1 tCIOV - Select a value from the left. Select a value from the left. Select a value from the left. Select a value from the left. Select a value from the left. Select a value from the left. BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Pin Configuration 1. SNT-6A Top view 1 2 3 Table 6 6 5 4 Figure 2 Pin No. Symbol 1 VM 2 CO 3 DO 4 5 6 VSS VDD VINI Description Input pin for external negative voltage Connection pin of charge control FET gate (CMOS output) Connection pin of discharge control FET gate (CMOS output) Input pin for negative power supply Input pin for positive power supply Overcurrent detection pin 2. DFN-6(1414)A Top view 1 6 3 4 Bottom view 6 1 4 3 *1 Table 7 Pin No. 1 2 3 4 Symbol VSS VDD VINI VM 5 CO 6 DO Description Input pin for negative power supply Input pin for positive power supply Overcurrent detection pin Input pin for external negative voltage Connection pin of charge control FET gate (CMOS output) Connection pin of discharge control FET gate (CMOS output) Figure 3 *1. Connect the heat sink of backside at shadowed area to the board, and set electric potential open or VDD. However, do not use it as the function of electrode. 9 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Absolute Maximum Ratings Table 8 (Ta = +25C unless otherwise specified) Item Symbol Applied Pin Absolute Maximum Rating Unit Input voltage between VDD pin and VSS pin VDS VDD VSS - 0.3 to VSS + 6 V VINI pin input voltage VVINI VINI VDD - 6 to VDD + 0.3 V VM pin input voltage VVM VM VDD - 28 to VDD + 0.3 V DO pin output voltage VDO DO VSS - 0.3 to VDD + 0.3 V CO pin output voltage Operation ambient temperature VCO Topr CO - VVM - 0.3 to VDD + 0.3 -40 to +85 V C Storage temperature Tstg - -55 to +125 C Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. Thermal Resistance Value Table 9 Item Junction-to-ambient thermal resistance*1 *1. JA Condition Board A Board B SNT-6A Board C Board D Board E Board A Board B DFN-6(1414)A Board C Board D Board E Test environment: compliance with JEDEC STANDARD JESD51-2A Remark 10 Symbol Refer to " Power Dissipation" and "Test Board" for details. Min. - Typ. 224 Max. - Unit C/W - - - - - - - - - 176 - - - 315 276 - - - - - - - - - - - - C/W C/W C/W C/W C/W C/W C/W C/W C/W BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Electrical Characteristics 1. Ta = +25C Item Table 10 Symbol Condition Min. (Ta = +25C unless otherwise specified) Test Typ. Max. Unit Circuit Detection Voltage Overcharge detection voltage VCU Overcharge release voltage VCL Overdischarge detection voltage VDL Overdischarge release voltage VDU Discharge overcurrent detection voltage 1 Discharge overcurrent detection voltage 2 Load short-circuiting detection voltage Charge overcurrent detection voltage Discharge overcurrent release voltage 0 V Battery Charge 0 V battery charge starting charger voltage 0 V battery charge inhibition battery voltage Internal Resistance Resistance between VDD pin and VM pin Resistance between VM pin and VSS pin Input Voltage Operation voltage between VDD pin and VSS pin Operation voltage between VDD pin and VM pin Input Current Current consumption during operation Current consumption during power-down Current consumption during overdischarge Output Resistance CO pin resistance "H" CO pin resistance "L" DO pin resistance "H" DO pin resistance "L" Delay Time Overcharge detection delay time Overdischarge detection delay time Discharge overcurrent detection delay time 1 Discharge overcurrent detection delay time 2 Load short-circuiting detection delay time Charge overcurrent detection delay time - Ta = -10C to +60C VCL VCU *1 VCL = VCU - VDL VDU VDL = VDU VDIOV1 VDIOV2 VSHORT VCIOV VRIOV VDD = 3.4 V - - - - VCU - 0.020 VCU - 0.025 VCU VCU VCU + 0.020 VCU + 0.025 V V 1 1 VCL - 0.050 VCL VCL + 0.050 V 1 VCL - 0.025 VDL - 0.050 VDU - 0.100 VCL VDL VDU VCL + 0.020 VDL + 0.050 VDU + 0.100 V V V 1 2 2 VDU - 0.050 VDU VDU + 0.050 V VDIOV1 - 0.003 VDIOV1 VDIOV1 + 0.003 V VDIOV2 - 0.005 VDIOV2 VDIOV2 + 0.005 V VSHORT - 0.020 VSHORT VSHORT + 0.020 V VCIOV - 0.003 VCIOV VCIOV + 0.003 V VDD x 0.77 VDD x 0.8 VDD x 0.83 V 2 2 2 2 2 2 V0CHA V0INH 0 V battery charge enabled 0 V battery charge inhibited 0.0 0.9 0.7 1.2 1.0 1.5 V V 2 2 RVMD RVMS VDD = 1.8 V, VVM = 0 V VDD = 3.4 V, VVM = 1.0 V 500 5 1000 10 2000 15 k k 3 3 VDSOP1 - 1.5 - 6.0 V - VDSOP2 - 1.5 - 28 V - - - - 2.0 - - 4.0 0.05 0.5 A A A 3 3 3 IOPE IPDN IOPED VDD = 3.4 V, VVM = 0 V VDD = VVM = 1.5 V VDD = VVM = 1.5 V RCOH RCOL RDOH RDOL - - - - 5 5 5 5 10 10 10 10 20 20 20 20 k k k k 4 4 4 4 tCU tDL tDIOV1 tDIOV2 tSHORT tCIOV - - - - - - tCU x 0.7 tDL x 0.7 tDIOV1 x 0.7 tDIOV2 x 0.7 tSHORT x 0.7 tCIOV x 0.7 tCU tDL tCU x 1.3 tDL x 1.3 tDIOV1 x 1.3 tDIOV2 x 1.3 tSHORT x 1.3 tCIOV x 1.3 - - - - - - 5 5 5 5 5 5 tDIOV1 tDIOV2 tSHORT tCIOV *1. Since products are not screened at high and low temperature, the specification for this temperature range is guaranteed by design, not tested in production. 11 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 2. Ta = -20C to +60C*1 Table 11 Item Symbol Detection Voltage Overcharge detection voltage VCU Overcharge release voltage VCL Overdischarge detection voltage VDL Condition - VCL VCU VCL = VCU - VDL VDU VDL = VDU Overdischarge release voltage VDU Discharge overcurrent detection voltage 1 Discharge overcurrent detection voltage 2 Load short-circuiting detection voltage Charge overcurrent detection voltage Discharge overcurrent release voltage 0 V Battery Charge 0 V battery charge starting charger voltage 0 V battery charge inhibition battery voltage Internal Resistance Resistance between VDD pin and VM pin Resistance between VM pin and VSS pin Input Voltage Operation voltage between VDD pin and VSS pin Operation voltage between VDD pin and VM pin Input Current Current consumption during operation Current consumption during power-down Current consumption during overdischarge Output Resistance CO pin resistance "H" CO pin resistance "L" DO pin resistance "H" DO pin resistance "L" Delay Time Overcharge detection delay time Overdischarge detection delay time Discharge overcurrent detection delay time 1 Discharge overcurrent detection delay time 2 Load short-circuiting detection delay time Charge overcurrent detection delay time VDIOV1 VDIOV2 VSHORT VCIOV VRIOV VDD = 3.4 V - - - - (Ta = -20C to +60C*1 unless otherwise specified) Test Min. Typ. Max. Unit Circuit VCU - 0.035 VCU VCU + 0.027 VCL - 0.065 VCL VCL + 0.057 VCL - 0.040 VCL VCL + 0.027 VDL - 0.060 VDL VDL + 0.055 VDU - 0.110 VDU VDU + 0.105 VDU - 0.060 VDU VDU + 0.055 VDIOV1 - 0.003 VDIOV1 VDIOV1 + 0.003 VDIOV2 - 0.005 VDIOV2 VDIOV2 + 0.005 VSHORT - 0.020 VSHORT VSHORT + 0.020 VCIOV - 0.003 VCIOV VCIOV + 0.003 VDD x 0.77 VDD x 0.8 VDD x 0.83 V V V V V V V V V V V 1 1 1 2 2 2 2 2 2 2 2 V0CHA V0INH 0 V battery charge enabled 0 V battery charge inhibited 0.0 0.7 0.7 1.2 1.5 1.7 V V 2 2 RVMD RVMS VDD = 1.8 V, VVM = 0 V VDD = 3.4 V, VVM = 1.0 V 250 3.5 1000 10 3000 20 k k 3 3 VDSOP1 - 1.5 - 6.0 V - VDSOP2 - 1.5 - 28 V - - - - 2.0 - - 5.0 0.1 1.0 A A A 3 3 3 IOPE IPDN IOPED VDD = 3.4 V, VVM = 0 V VDD = VVM = 1.5 V VDD = VVM = 1.5 V RCOH RCOL RDOH RDOL - - - - 2.5 2.5 2.5 2.5 10 10 10 10 30 30 30 30 k k k k 4 4 4 4 tCU tDL tDIOV1 tDIOV2 tSHORT tCIOV - - - - - - tCU x 0.55 tDL x 0.55 tDIOV1 x 0.55 tDIOV2 x 0.55 tSHORT x 0.55 tCIOV x 0.55 tCU tDL tCU x 2.0 tDL x 2.0 tDIOV1 x 2.0 tDIOV2 x 2.0 tSHORT x 2.0 tCIOV x 2.0 - - - - - - 5 5 5 5 5 5 tDIOV1 tDIOV2 tSHORT tCIOV *1. Since products are not screened at high and low temperature, the specification for this temperature range is guaranteed by design, not tested in production. 12 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 3. Ta = -40C to +85C*1 Table 12 Item Detection Voltage Overcharge detection voltage Symbol - VCU Overcharge release voltage VCL Overdischarge detection voltage VDL Overdischarge release voltage VDU Discharge overcurrent detection voltage 1 Discharge overcurrent detection voltage 2 Load short-circuiting detection voltage Charge overcurrent detection voltage Discharge overcurrent release voltage 0 V Battery Charge 0 V battery charge starting charger voltage 0 V battery charge inhibition battery voltage Internal Resistance Resistance between VDD pin and VM pin Resistance between VM pin and VSS pin Input Voltage Operation voltage between VDD pin and VSS pin Operation voltage between VDD pin and VM pin Input Current Current consumption during operation Current consumption during power-down Current consumption during overdischarge Output Resistance CO pin resistance "H" CO pin resistance "L" DO pin resistance "H" DO pin resistance "L" Delay Time Overcharge detection delay time Overdischarge detection delay time Discharge overcurrent detection delay time 1 Discharge overcurrent detection delay time 2 Load short-circuiting detection delay time Charge overcurrent detection delay time Condition VCL VCU VCL = VCU - VDL VDU VDL = VDU VDIOV1 VDIOV2 VSHORT VCIOV VRIOV VDD = 3.4 V - - - - (Ta = -40C to +85C*1 unless otherwise specified) Test Min. Typ. Max. Unit Circuit VCU - 0.045 VCL - 0.080 VCU VCL VCU + 0.030 VCL + 0.060 V V 1 1 VCL - 0.050 VDL - 0.080 VDU - 0.130 VCL VDL VDU VCL + 0.030 VDL + 0.060 VDU + 0.110 V V V 1 2 2 V V V V V V 2 2 2 2 2 2 VDU - 0.080 VDU VDU + 0.060 VDIOV1 - 0.003 VDIOV1 VDIOV1 + 0.003 VDIOV2 - 0.005 VDIOV2 VDIOV2 + 0.005 VSHORT - 0.020 VSHORT VSHORT + 0.020 VCIOV - 0.003 VCIOV VCIOV + 0.003 VDD x 0.77 VDD x 0.8 VDD x 0.83 V0CHA V0INH 0 V battery charge enabled 0 V battery charge inhibited 0.0 0.7 0.7 1.2 1.5 1.7 V V 2 2 RVMD RVMS VDD = 1.8 V, VVM = 0 V VDD = 3.4 V, VVM = 1.0 V 250 3.5 1000 10 3000 20 k k 3 3 VDSOP1 - 1.5 - 6.0 V - VDSOP2 - 1.5 - 28 V - - - - 2.0 - - 5.0 0.1 1.0 A A A 3 3 3 IOPE IPDN IOPED VDD = 3.4 V, VVM = 0 V VDD = VVM = 1.5 V VDD = VVM = 1.5 V RCOH RCOL RDOH RDOL - - - - 2.5 2.5 2.5 2.5 10 10 10 10 30 30 30 30 k k k k 4 4 4 4 tCU tDL tDIOV1 tDIOV2 tSHORT tCIOV - - - - - - tCU x 0.4 tDL x 0.4 tDIOV1 x 0.4 tDIOV2 x 0.4 tSHORT x 0.4 tCIOV x 0.4 tCU tDL tCU x 2.5 tDL x 2.5 tDIOV1 x 2.5 tDIOV2 x 2.5 tSHORT x 2.5 tCIOV x 2.5 - - - - - - 5 5 5 5 5 5 tDIOV1 tDIOV2 tSHORT tCIOV *1. Since products are not screened at high and low temperature, the specification for this temperature range is guaranteed by design, not tested in production. 13 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Test Circuits Caution Unless otherwise specified, the output voltage levels "H" and "L" at CO pin (VCO) and DO pin (VDO) are judged by the threshold voltage (1.0 V) of the N-channel FET. Judge the CO pin level with respect to VVM and the DO pin level with respect to VSS. 1. Overcharge detection voltage, overcharge release voltage (Test circuit 1) Overcharge detection voltage (VCU) is defined as the voltage V1 at which VCO goes from "H" to "L" when the voltage V1 is gradually increased from the starting condition of V1 = 3.4 V. Overcharge release voltage (VCL) is defined as the voltage V1 at which VCO goes from "L" to "H" when the voltage V1 is then gradually decreased. Overcharge hysteresis voltage (VHC) is defined as the difference between VCU and VCL. 2. Overdischarge detection voltage, overdischarge release voltage (Test circuit 2) Overdischarge detection voltage (VDL) is defined as the voltage V1 at which VDO goes from "H" to "L" when the voltage V1 is gradually decreased from the starting conditions of V1 = 3.4 V, V2 = V5 = 0 V. Overdischarge release voltage (VDU) is defined as the voltage V1 at which VDO goes from "L" to "H" when setting V2 = 0.01 V, V5 = 0 V and when the voltage V1 is then gradually increased. Overdischarge hysteresis voltage (VHD) is defined as the difference between VDU and VDL. 3. Discharge overcurrent detection voltage 1, discharge overcurrent release voltage (Test circuit 2) 3. 1 Release voltage of discharge overcurrent status "VDIOV1" Discharge overcurrent detection voltage 1 (VDIOV1) is defined as the voltage V5 whose delay time for changing VDO from "H" to "L" is discharge overcurrent detection delay time 1 (tDIOV1) when the voltage V5 is increased from the starting conditions of V1 = V2 = 3.4 V, V5 = 0 V. VDO goes from "L" to "H" when setting V5 = 0 V and when the voltage V2 is then gradually decreased to VDIOV1 typ. or lower. 3. 2 Release voltage of discharge overcurrent status "VRIOV" VDIOV1 is defined as the voltage V5 whose delay time for changing VDO from "H" to "L" is tDIOV1 when the voltage V5 is increased from the starting conditions of V1 = V2 = 3.4 V, V5 = 0 V. Discharge overcurrent release voltage (VRIOV) is defined as the voltage V2 at which VDO goes from "L" to "H" when setting V5 = 0 V and when the voltage V2 is then gradually decreased. 4. Discharge overcurrent detection voltage 2 (for only the products whose discharge overcurrent detection voltage 2 is set) (Test circuit 2) Discharge overcurrent detection voltage 2 (VDIOV2) is defined as the voltage V5 whose delay time for changing VDO from "H" to "L" is discharge overcurrent detection delay time 2 (tDIOV2) when the voltage V5 is increased from the starting conditions of V1 = V2 = 3.4 V, V5 = 0 V. 5. Load short-circuiting detection voltage (Test circuit 2) Load short-circuiting detection voltage (VSHORT) is defined as the voltage V5 whose delay time for changing VDO from "H" to "L" is load short-circuiting detection delay time (tSHORT) when the voltage V5 is increased from the starting conditions of V1 = V2 = 3.4 V, V5 = 0 V. 6. Charge overcurrent detection voltage (Test circuit 2) Charge overcurrent detection voltage (VCIOV) is defined as the voltage V5 whose delay time for changing VCO from "H" to "L" is charge overcurrent detection delay time (tCIOV) when the voltage V5 is decreased from the starting conditions of V1 = 3.4 V, V2 = V5 = 0 V. 14 Rev.2.4_00 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series 7. Current consumption during operation (Test circuit 3) The current consumption during operation (IOPE) is the current that flows through the VDD pin (IDD) under the set conditions of V1 = 3.4 V and V2 = V5 = 0 V. 8. Current consumption during power-down, current consumption during overdischarge (Test circuit 3) 8. 1 With power-down function The current consumption during power-down (IPDN) is IDD under the set conditions of V1 = V2 = 1.5 V, V5 = 0 V. 8. 2 Without power-down function The current consumption during overdischarge (IOPED) is IDD under the set conditions of V1 = V2 = 1.5 V, V5 = 0 V. 9. Resistance between VDD pin and VM pin (Test circuit 3) RVMD is the resistance between VDD pin and VM pin under the set conditions of V1 = 1.8 V, V2 = V5 = 0 V. 10. Resistance between VM pin and VSS pin (Release condition of discharge overcurrent status "load disconnection") (Test circuit 3) RVMS is the resistance between VM pin and VSS pin when the voltage V5 is decreased to 0 V from the starting conditions of V1 = 3.4 V, V2 = V5 = 1.0 V. 11. CO pin resistance "H" (Test circuit 4) The CO pin resistance "H" (RCOH) is the resistance between VDD pin and CO pin under the set conditions of V1 = 3.4 V, V2 = V5 = 0 V, V3 = 3.0 V. 12. CO pin resistance "L" (Test circuit 4) The CO pin resistance "L" (RCOL) is the resistance between VM pin and CO pin under the set conditions of V1 = 4.7 V, V2 = V5 = 0 V, V3 = 0.4 V. 13. DO pin resistance "H" (Test circuit 4) The DO pin resistance "H" (RDOH) is the resistance between VDD pin and DO pin under the set conditions of V1 = 3.4 V, V2 = V5 = 0 V, V4 = 3.0 V. 14. DO pin resistance "L" (Test circuit 4) The DO pin resistance "L" (RDOL) is the resistance between VSS pin and DO pin under the set conditions of V1 = 1.8 V, V2 = V5 = 0 V, V4 = 0.4 V. 15. Overcharge detection delay time (Test circuit 5) The overcharge detection delay time (tCU) is the time needed for VCO to go to "L" just after the voltage V1 increases and exceeds VCU under the set conditions of V1 = 3.4 V, V2 = V5 = 0 V. 15 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 16. Overdischarge detection delay time (Test circuit 5) The overdischarge detection delay time (tDL) is the time needed for VDO to go to "L" after the voltage V1 decreases and falls below VDL under the set conditions of V1 = 3.4 V, V2 = V5 = 0 V. 17. Discharge overcurrent detection delay time 1 (Test circuit 5) The discharge overcurrent detection delay time 1 (tDIOV1) is the time needed for VDO to go to "L" after the voltage V5 increases and exceeds VDIOV1 under the set conditions of V1 = V2 = 3.4 V, V5 = 0 V. 18. Discharge overcurrent detection delay time 2 (for only the products whose discharge overcurrent detection voltage 2 is set) (Test circuit 5) The discharge overcurrent detection delay time 2 (tDIOV2) is the time needed for VDO to go to "L" after the voltage V5 increases and exceeds VDIOV2 under the set conditions of V1 = V2 = 3.4 V, V5 = 0 V. 19. Load short-circuiting detection delay time (Test circuit 5) The load short-circuiting detection delay time (tSHORT) is the time needed for VDO to go to "L" after the voltage V5 increases and exceeds VSHORT under the set conditions of V1 = V2 = 3.4 V, V5 = 0 V. 20. Charge overcurrent detection delay time (Test circuit 5) The charge overcurrent detection delay time (tCIOV) is the time needed for VCO to go to "L" after the voltage V5 decreases and falls below VCIOV under the set conditions of V1 = 3.4 V, V2 = V5 = 0 V. 21. 0 V battery charge starting charger voltage (0 V battery charge enabled) (Test circuit 2) The 0 V battery charge starting charger voltage (V0CHA) is defined as the absolute value of voltage V2 at which VCO goes to "H" (VCO = VDD) when the voltage V2 is gradually decreased from the starting condition of V1 = V2 = V5 = 0 V. 22. 0 V battery charge inhibition battery voltage (0 V battery charge inhibited) (Test circuit 2) The 0 V battery charge inhibition battery voltage (V0INH) is defined as the voltage V1 at which VCO goes to "L" (VCO = VVM) when the voltage V1 is gradually decreased, after setting V1 = 1.9 V, V2 = -2.0 V, V5 = 0 V. 16 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 R1 = 330 IDD A VDD V1 S-82A1A Series V1 VSS C1 = 0.1 F DO DO V5 V VCO CO V VDO V VCO V2 COM COM Figure 4 Test Circuit 1 IDD A VM VINI CO V VDO S-82A1A Series VSS VM VINI VDD Figure 5 Test Circuit 2 VDD V1 VDD V1 S-82A1A Series VSS VM VINI DO CO V5 S-82A1A Series VSS VINI A IVM V2 COM VM DO V5 CO A IDO A ICO V4 V3 V2 COM Figure 6 Test Circuit 3 Figure 7 Test Circuit 4 VDD V1 S-82A1A Series VSS VINI V5 VM DO CO Oscilloscope Oscilloscope V2 COM Figure 8 Test Circuit 5 17 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Operation Remark Refer to " Battery Protection IC Connection Example". 1. Normal status The S-82A1A Series monitors the voltage of the battery connected between VDD pin and VSS pin, the voltage between VINI pin and VSS pin to control charging and discharging. When the battery voltage is in the range from overdischarge detection voltage (VDL) to overcharge detection voltage (VCU), and the VINI pin voltage is in the range from charge overcurrent detection voltage (VCIOV) to discharge overcurrent detection voltage 1 (VDIOV1), the S-82A1A Series turns both the charge and discharge control FETs on. This condition is called the normal status, and in this condition charging and discharging can be carried out freely. The resistance between VDD pin and VM pin (RVMD), and the resistance between VM pin and VSS pin (RVMS) are not connected in the normal status. Caution After the battery is connected, discharging may not be carried out. In this case, the S-82A1A Series returns to the normal status by connecting a charger. 2. Overcharge status 2. 1 VCL VCU (Product in which overcharge release voltage differs from overcharge detection voltage) When the battery voltage becomes higher than VCU during charging in the normal status and the condition continues for the overcharge detection delay time (tCU) or longer, the S-82A1A Series turns the charge control FET off to stop charging. This condition is called the overcharge status. The overcharge status is released in the following two cases. (1) In the case that the VM pin voltage is lower than 0.35 V typ., the S-82A1A Series releases the overcharge status when the battery voltage falls below overcharge release voltage (VCL). (2) In the case that the VM pin voltage is equal to or higher than 0.35 V typ., the S-82A1A Series releases the overcharge status when the battery voltage falls below VCU. When the discharge is started by connecting a load after the overcharge detection, the VM pin voltage rises by the Vf voltage of the parasitic diode than the VSS pin voltage, because the discharge current flows through the parasitic diode in the charge control FET. If this VM pin voltage is equal to or higher than 0.35 V typ., the S-82A1A Series releases the overcharge status when the battery voltage is equal to or lower than VCU. Caution If the battery is charged to a voltage higher than VCU and the battery voltage does not fall below VCU even when a heavy load is connected, discharge overcurrent detection and load short-circuiting detection do not function until the battery voltage falls below VCU. Since an actual battery has an internal impedance of tens of m, the battery voltage drops immediately after a heavy load that causes overcurrent is connected, and discharge overcurrent detection and load short-circuiting detection function. 2. 2 VCL = VCU (Product in which overcharge release voltage is the same as overcharge detection voltage) When the battery voltage becomes higher than VCU during charging in the normal status and the condition continues for the overcharge detection delay time (tCU) or longer, the S-82A1A Series turns the charge control FET off to stop charging. This condition is called the overcharge status. In the case that the VM pin voltage is equal to or higher than 0.35 V typ. and the battery voltage falls below VCU, the S-82A1A Series releases the overcharge status. When the discharge is started by connecting a load after the overcharge detection, the VM pin voltage rises by the Vf voltage of the parasitic diode than the VSS pin voltage, because the discharge current flows through the parasitic diode in the charge control FET. If this VM pin voltage is equal to or higher than 0.35 V typ., the S-82A1A Series releases the overcharge status when the battery voltage is equal to or lower than VCU. Caution 1. If the battery is charged to a voltage higher than VCU and the battery voltage does not fall below VCU even when a heavy load is connected, discharge overcurrent detection and load shortcircuiting detection do not function until the battery voltage falls below VCU. Since an actual battery has an internal impedance of tens of m, the battery voltage drops immediately after a heavy load that causes overcurrent is connected, and discharge overcurrent detection and load short-circuiting detection function. 2. When a charger is connected after overcharge detection, the overcharge status is not released even if the battery voltage is below VCL. The overcharge status is released when the discharge current flows and the VM pin voltage goes over 0.35 V typ. by removing the charger. 18 Rev.2.4_00 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series 3. Overdischarge status When the battery voltage falls below VDL during discharging in the normal status and the condition continues for the overdischarge detection delay time (tDL) or longer, the S-82A1A Series turns the discharge control FET off to stop discharging. This condition is called the overdischarge status. Under the overdischarge status, VDD pin and VM pin are shorted by RVMD in the S-82A1A Series. The VM pin voltage is pulled up by RVMD. When connecting a charger in the overdischarge status, the battery voltage reaches VDL or higher and the S-82A1A Series releases the overdischarge status if the VM pin voltage falls below 0 V typ. The battery voltage reaches the overdischarge release voltage (VDU) or higher and the S-82A1A Series releases the overdischarge status if the VM pin voltage does not fall below 0 V typ. RVMS is not connected in the overdischarge status. 3. 1 With power-down function Under the overdischarge status, when voltage difference between VDD pin and VM pin is 0.8 V typ. or lower, the power-down function works and the current consumption is reduced to the current consumption during powerdown (IPDN). By connecting a battery charger, the power-down function is released when the VM pin voltage is 0.7 V typ. or lower. * When a battery is not connected to a charger and the VM pin voltage 0.7 V typ., the S-82A1A Series maintains the overdischarge status even when the battery voltage reaches VDU or higher. * When a battery is connected to a charger and 0.7 V typ. > the VM pin voltage > 0 V typ., the battery voltage reaches VDU or higher and the S-82A1A Series releases the overdischarge status. * When a battery is connected to a charger and 0 V typ. the VM pin voltage, the battery voltage reaches VDL or higher and the S-82A1A Series releases the overdischarge status. 3. 2 Without power-down function The power-down function does not work even when voltage difference between VDD pin and VM pin is 0.8 V typ. or lower. * When a battery is not connected to a charger and the VM pin voltage 0.7 V typ., the battery voltage reaches VDU or higher and the S-82A1A Series releases the overdischarge status. * When a battery is connected to a charger and 0.7 V typ. > the VM pin voltage > 0 V typ., the battery voltage reaches VDU or higher and the S-82A1A Series releases the overdischarge status. * When a battery is connected to a charger and 0 V typ. the VM pin voltage, the battery voltage reaches VDL or higher and the S-82A1A Series releases the overdischarge status. 4. Discharge overcurrent status (discharge overcurrent 1, discharge overcurrent 2, load short circuiting) When a battery in the normal status is in the status where the VINI pin voltage is equal to or higher than VDIOV1 because the discharge current is equal to or higher than the specified value and the status lasts for the discharge overcurrent detection delay time 1 (tDIOV1) or longer, the discharge control FET is turned off and discharging is stopped. This status is called the discharge overcurrent status. 4. 1 Release condition of discharge overcurrent status "load disconnection" and release voltage of discharge overcurrent status "VDIOV1" Under the discharge overcurrent status, VM pin and VSS pin are shorted by RVMS in the S-82A1A Series. However, the VM pin voltage is the VDD pin voltage due to the load as long as the load is connected. When the load is disconnected, the VM pin returns to the VSS pin voltage. When the VM pin voltage returns to VDIOV1 or lower, the S-82A1A Series releases the discharge overcurrent status. RVMD is not connected in the discharge overcurrent status. 4. 2 Release condition of discharge overcurrent status "load disconnection" and release voltage of discharge overcurrent status "VRIOV" Under the discharge overcurrent status, VM pin and VSS pin are shorted by RVMS in the S-82A1A Series. However, the VM pin voltage is the VDD pin voltage due to the load as long as the load is connected. When the load is disconnected, the VM pin returns to the VSS pin voltage. When the VM pin voltage returns to VRIOV or lower, the S-82A1A Series releases the discharge overcurrent status. RVMD is not connected in the discharge overcurrent status. 19 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 4. 3 Release condition of discharge overcurrent status "charger connection" Under the discharge overcurrent status, VDD pin and VM pin are shorted by RVMD in the S-82A1A Series. When a battery is connected to a charger and the VM pin voltage returns to VDIOV1 or lower, the S-82A1A Series releases the discharge overcurrent status. RVMS is not connected in the discharge overcurrent status. 5. Charge overcurrent status When a battery in the normal status is in the status where the VINI pin voltage is equal to or lower than VCIOV because the charge current is equal to or higher than the specified value and the status lasts for the charge overcurrent detection delay time (tCIOV) or longer, the charge control FET is turned off and charging is stopped. This status is called the charge overcurrent status. The S-82A1A Series releases the charge overcurrent status when the discharge current flows and the VM pin voltage is 0.35 V typ. or higher by removing the charger. The charge overcurrent detection does not function in the overdischarge status. 6. 0 V battery charge enabled This function is used to recharge a connected battery whose voltage is 0 V due to self-discharge. When the 0 V battery charge starting charger voltage (V0CHA) or a higher voltage is applied between the EB+ and EB- pins by connecting a charger, the charge control FET gate is fixed to the VDD pin voltage. When the voltage between the gate and source of the charge control FET becomes equal to or higher than the threshold voltage due to the charger voltage, the charge control FET is turned on to start charging. At this time, the discharge control FET is off and the charging current flows through the internal parasitic diode in the discharging control FET. When the battery voltage becomes equal to or higher than VDL, the S-82A1A Series returns to the normal status. Caution 1. Some battery providers do not recommend charging for a completely self-discharged lithium-ion rechargeable battery. Please ask the battery provider to determine whether to enable or inhibit the 0 V battery charge. 2. The 0 V battery charge has higher priority than the charge overcurrent detection function. Consequently, a product in which use of the 0 V battery charge is enabled charges a battery forcibly and the charge overcurrent cannot be detected when the battery voltage is lower than VDL. 7. 0 V battery charge inhibited This function inhibits recharging when a battery that is internally short-circuited (0 V battery) is connected. When the battery voltage is the 0 V battery charge inhibition battery voltage (V0INH) or lower, the charge control FET gate is fixed to the EB- pin voltage to inhibit charging. When the battery voltage is V0INH or higher, charging can be performed. Caution Some battery providers do not recommend charging for a completely self-discharged lithium-ion rechargeable battery. Please ask the battery provider to determine whether to enable or inhibit the 0 V battery charge. 20 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 8. Delay circuit The detection delay times are determined by dividing a clock of approximately 4 kHz by the counter. Remark tDIOV1, tDIOV2 and tSHORT start when VDIOV1 is detected. When VDIOV2 or VSHORT is detected over tDIOV2 or tSHORT after the detection of VDIOV1, the S-82A1A Series turns the discharge control FET off within tDIOV2 or tSHORT of each detection. VDD DO pin voltage tD VSS VDD tSHORT 0 tD tSHORT Time VSHORT VINI pin voltage VDIOV1 VSS Time Figure 9 21 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Timing Charts 1. Overcharge detection, overdischarge detection VCU VCL (VCU - VHC) Battery voltage VDU (VDL + VHD) VDL VDD DO pin voltage VSS VDD CO pin voltage VSS VEB- VDD VM pin voltage 0.35 V typ. VSS VEB- VDD VINI pin voltage VDIOV1 VSS VCIOV Charger connection Load connection Overcharge detection delay time (tCU) *1 Status (1) Overdischarge detection delay time (tDL) (2) (1) *1. (1): Normal status (2): Overcharge status (3): Overdischarge status Remark The charger is assumed to charge with a constant current. Figure 10 22 (3) (1) BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 2. Discharge overcurrent detection 2. 1 Release condition of discharge overcurrent status "load disconnection" VCU VCL (VCU - VHC) Battery voltage VDU (VDL + VHD) VDL VDD DO pin voltage VSS VDD CO pin voltage VSS VM pin voltage VDD VRIOV V VDIVSHORT DIOV1 VSS VDD VINI pin voltage VSHORT VDIOV2 VDIOV1 VSS Load connection Status Discharge overcurrent detection delay time 1 (tDIOV1) *1 (1) (2) Discharge overcurrent detection delay time 2 (tDIOV2) (1) (2) Load short-circuiting detection delay time (tSHORT) (1) (2) (1) *1. (1): Normal status (2): Discharge overcurrent status Remark The charger is assumed to charge with a constant current. Figure 11 23 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 2. 2 Release condition of discharge overcurrent status "charger connection" VCU VCL (VCU - VHC) Battery voltage VDU (VDL + VHD) VDL VDD DO pin voltage VSS VDD CO pin voltage VSS VDD VM pin voltage VDIOV1 VSS VEB- VDD VINI pin voltage VSHORT VDIOV2 VDIOV1 VSS VCIOV Charger connection Load connection Status *1 Discharge overcurrent detection delay time 1 (tDIOV1) (1) (2) Discharge overcurrent detection delay time 2 (tDIOV2) (1) *1. (1): Normal status (2): Discharge overcurrent status Remark The charger is assumed to charge with a constant current. Figure 12 24 (2) Load short-circuiting detection delay time (tSHORT) (1) (2) (1) BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 3. Charge overcurrent detection VCU VCL (VCU - VHC) Battery voltage VDU (VDL + VHD) VDL VDD DO pin voltage VSS VDD CO pin voltage VSS VEB- VDD VM pin voltage 0.35 V typ. V VSS CIOV VEB- VDD VINI pin voltage VDIOV1 VSS VCIOV Charger connection Load connection Status*1 Charge overcurrent detection delay time (tCIOV) (2) (1) Overdischarge detection delay time (tDL) (1) Charge overcurrent detection delay time (tCIOV) (3) (1) (2) *1. (1): Normal status (2): Charge overcurrent status (3): Overdischarge status Remark The charger is assumed to charge with a constant current. Figure 13 25 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Battery Protection IC Connection Example EB+ R1 VDD Battery C1 S-82A1A Series VSS VINI R3 DO CO FET1 VM FET2 R2 EB- Figure 14 Symbol FET1 FET2 Part N-channel MOS FET N-channel MOS FET R1 Resistor C1 Capacitor R2 Resistor Table 13 Constants for External Components Purpose Min. Typ. Max. Remark Threshold voltage Overdischarge - - - Discharge control detection voltage*1 Threshold voltage Overdischarge - - - Charge control detection voltage*1 ESD protection, Caution should be exercised when 270 330 1 k setting VDIOV1 30 mV, VCIOV -30 mV.*2 For power fluctuation Caution should be exercised when 0.068 F 0.1 F 1.0 F For power fluctuation setting VDIOV1 30 mV, VCIOV -30 mV.*2 ESD protection, 300 470 1.5 k - Protection for reverse connection of a charger - 5 m - - Overcurrent detection R3 Resistor *1. If an FET with a threshold voltage equal to or higher than the overdischarge detection voltage is used, discharging may be stopped before overdischarge is detected. *2. When setting VDIOV1 30 mV, VCIOV -30 mV for power fluctuation protection, the condition of R1 x C1 100 F * should be met. Caution 1. The constants may be changed without notice. 2. It has not been confirmed whether the operation is normal or not in circuits other than the connection example. In addition, the connection example and the constants do not guarantee proper operation. Perform thorough evaluation using the actual application to set the constants. 26 Rev.2.4_00 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Precautions * The application conditions for the input voltage, output voltage, and load current should not exceed the package power dissipation. * Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic protection circuit. * ABLIC Inc. claims no responsibility for any and all disputes arising out of or in connection with any infringement by products including this IC of patents owned by a third party. 27 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Characteristics (Typical Data) 1. Current consumption 1. 2 IPDN vs. Ta 5.0 0.100 4.0 0.075 IPDN [A] IOPE [A] 1. 1 IOPE vs. Ta 3.0 2.0 1.0 0.0 -40 -25 0 25 Ta [C] 50 75 85 0 25 Ta [C] 50 75 85 0.050 0.025 0.000 -40 -25 0 25 Ta [C] 50 1. 3 IOPED vs. Ta IOPED [A] 1.00 0.75 0.50 0.25 0.00 -40 -25 1. 4 IOPE vs. VDD 5.0 5.0 4.0 4.0 3.0 2.0 3.0 2.0 1.0 1.0 0.0 0.0 VDD [V] 28 1. 4. 2 Without power-down function IOPE [A] IOPE [A] 1. 4. 1 With power-down function VDD [V] 75 85 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 2. Detection voltage 2. 2 VCL vs. Ta 4.52 4.36 4.50 4.32 VCL [V] VCU [V] 2. 1 VCU vs. Ta 4.48 4.46 4.44 4.24 -40 -25 0 25 Ta [C] 50 4.20 75 85 2. 3 VDL vs. Ta 2.38 2.64 2.34 2.57 2.30 2.26 2.22 -40 -25 50 75 85 2.43 - 2.36 - - - Ta [C] 2. 5 VDIOV1 vs. VDD 2. 6 VDIOV1 vs. Ta 0.029 0.029 0.027 0.027 VDIOV1 [V] VDIOV1 [V] 25 Ta [C] 2.50 Ta [C] 0.025 0.023 0.025 0.023 0.021 0.021 2.4 2.8 3.2 3.6 VDD [V] 4.0 4.4 - 2. 8 VDIOV2 vs. Ta 0.038 0.036 0.036 VDIOV2 [V] 0.038 0.034 0.032 0.034 0.032 0.030 0.030 2.4 - Ta [C] 2. 7 VDIOV2 vs. VDD VDIOV2 [V] 0 2. 4 VDU vs. Ta VDU [V] VDL [V] 4.28 2.8 3.2 3.6 VDD [V] 4.0 4.4 - - Ta [C] 29 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series 0.52 0.52 0.51 0.51 VSHORT [V] 2. 10 VSHORT vs. Ta VSHORT [V] 2. 9 VSHORT vs. VDD 0.50 0.49 0.48 2.4 2.8 3.2 3.6 VDD [V] 4.0 0.49 -40 -25 -0.016 -0.016 -0.018 -0.018 -0.020 -0.022 -0.024 2.4 0 25 Ta [C] 50 75 85 0 25 Ta [C] 50 75 85 2. 12 VCIOV vs. Ta VCIOV [V] VCIOV [V] 0.50 0.48 4.4 2. 11 VCIOV vs. VDD 30 Rev.2.4_00 2.8 3.2 3.6 VDD [V] 4.0 4.4 -0.020 -0.022 -0.024 -40 -25 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 3. Delay time 3. 2 tDL vs. Ta 2.5 160 2.0 120 tDL [ms] tCU [s] 3. 1 tCU vs. Ta 1.5 1.0 40 0.5 0.0 80 - 0 - - - Ta [C] Ta [C] 1250 1250 1000 1000 tDIOV1 [ms] 3. 4 tDIOV1 vs. Ta tDIOV1 [ms] 3. 3 tDIOV1 vs. VDD 750 500 0 0 2.4 2.8 3.2 3.6 VDD [V] 4.0 4.4 tDIOV2 [ms] tDIOV2 [ms] - 3. 6 tDIOV2 vs. Ta 80 60 40 20 2.4 - Ta [C] 3. 5 tDIOV2 vs. VDD 80 2.8 3.2 3.6 VDD [V] 3. 7 tSHORT vs. VDD 4.0 60 40 20 0 4.4 -40 -25 0 25 Ta [C] 50 75 85 3. 8 tSHORT vs. Ta 750 tSHORT [s] 750 tSHORT [s] 500 250 250 0 750 500 250 0 500 250 0 VDD [V] - - Ta [C] 31 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series 3. 10 tCIOV vs. Ta 20 20 15 15 tCIOV [ms] tCIOV [ms] 3. 9 tCIOV vs. VDD Rev.2.4_00 10 5 0 2.4 2.8 3.2 3.6 VDD [V] 4.0 10 5 0 4.4 -40 -25 0 25 Ta [C] 50 75 85 4. Output resistance 4. 2 RCOL vs. VCO 30 30 25 25 20 20 RCOL [k] RCOH [k] 4. 1 RCOH vs. VCO 15 10 0 1 2 3 VCO [V] 4 30 30 25 25 20 20 15 10 1 2 3 VCO [V] 4 5 1 2 3 VDO [V] 4 5 15 10 5 5 0 0 0 0 4. 4 RDOL vs. VDO RDOL [k] RDOH [k] 0 5 4. 3 RDOH vs. VDO 32 10 5 5 0 15 1 2 3 VDO [V] 4 5 0 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Marking Specifications 1. SNT-6A Top view 6 5 (1) to (3): (4) to (6): 4 Product code (Refer to Product name vs. Product code) Lot number (1) (2) (3) (4) (5) (6) 1 2 3 Product name vs. Product code Product Name S-82A1AAB-I6T1U S-82A1AAC-I6T1U S-82A1AAD-I6T1U S-82A1AAE-I6T1U S-82A1AAF-I6T1U S-82A1AAG-I6T1U S-82A1AAH-I6T1U S-82A1AAI-I6T1U S-82A1AAJ-I6T1U S-82A1AAK-I6T1U S-82A1AAL-I6T1U S-82A1AAM-I6T1U S-82A1AAN-I6T1U S-82A1AAO-I6T1U S-82A1AAP-I6T1U S-82A1AAQ-I6T1U S-82A1AAR-I6T1U S-82A1AAS-I6T1U S-82A1AAT-I6T1U S-82A1AAU-I6T1U S-82A1AAV-I6T1U S-82A1AAW-I6T1U S-82A1AAX-I6T1U S-82A1AAY-I6T1U S-82A1AAZ-I6T1U S-82A1ABM-I6T1U S-82A1ABN-I6T1U S-82A1ABR-I6T1U S-82A1ABT-I6T1U S-82A1ABW-I6T1U S-82A1ABX-I6T1U S-82A1ABY-I6T1U S-82A1ACA-I6T1U S-82A1ACH-I6T1U Product Code (1) (2) (3) 6 C B 6 C C 6 C D 6 C E 6 C F 6 C G 6 C H 6 C I 6 C J 6 C K 6 C L 6 C M 6 C N 6 C O 6 C P 6 C Q 6 C R 6 C S 6 C T 6 C U 6 C V 6 C W 6 C X 6 C Y 6 C Z 6 M M 6 M N 6 M R 6 M T 6 M W 6 M X 6 M Y 6 Y A 6 Y H 33 BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 2. DFN-6(1414)A 6 Top view 5 4 (1) to (3): (4): (5) to (8): (1) (2) (3) (4) (5) (6) (7) (8) 1 2 3 Product name vs. Product code Product Name S-82A1AAC-A6T5S S-82A1AAD-A6T5S S-82A1AAF-A6T5S S-82A1AAG-A6T5S S-82A1AAM-A6T5S S-82A1ABA-A6T5S S-82A1ABB-A6T5S S-82A1ABC-A6T5S S-82A1ABD-A6T5S S-82A1ABE-A6T5S S-82A1ABF-A6T5S S-82A1ABG-A6T5S S-82A1ABH-A6T5S S-82A1ABI-A6T5S S-82A1ABK-A6T5S S-82A1ABL-A6T5S S-82A1ABM-A6T5S S-82A1ABN-A6T5S S-82A1ABO-A6T5S S-82A1ABP-A6T5S S-82A1ABQ-A6T5S S-82A1ABV-A6T5S S-82A1ACE-A6T5S S-82A1ACF-A6T5S S-82A1ACG-A6T5S 34 Product Code (1) (2) (3) 6 C C 6 C D 6 C F 6 C G 6 C M 6 M A 6 M B 6 M C 6 M D 6 M E 6 M F 6 M G 6 M H 6 M I 6 M K 6 M L 6 M M 6 M N 6 M O 6 M P 6 M Q 6 M V 6 Y E 6 Y F 6 Y G Product code (Refer to Product name vs. Product code) Product code (Fixed) Lot number BATTERY PROTECTION IC FOR 1-CELL PACK S-82A1A Series Rev.2.4_00 Power Dissipation SNT-6A DFN-6(1414)A Tj = +125C max. 0.8 B 0.6 A 0.4 0.2 0.0 0 25 50 75 100 125 150 175 Tj = +125C max. 1.0 Power dissipation (PD) [W] Power dissipation (PD) [W] 1.0 0.8 0.6 0.4 B A 0.2 0.0 0 25 Ambient temperature (Ta) [C] 50 75 100 125 150 175 Ambient temperature (Ta) [C] Board A Power Dissipation (PD) 0.45 W Board A Power Dissipation (PD) B 0.57 W B 0.36 W C - C - D - D - E - E - 0.32 W 35 SNT-6A Test Board (1) Board A ICMountArea Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 2 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.070 - (2) Board B Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] Thermal via 1 2 3 4 Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - No. SNT6A-A-Board-SD-1.0 ABLIC Inc. DFN-6(1414)A Test Board ICMountArea (1) Board A Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] 1 2 3 4 Thermal via Specification 114.3 x 76.2 x t1.6 FR-4 2 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.070 - (2) Board B Item Size [mm] Material Number of copper foil layer Copper foil layer [mm] Thermal via 1 2 3 4 Specification 114.3 x 76.2 x t1.6 FR-4 4 Land pattern and wiring for testing: t0.070 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.035 74.2 x 74.2 x t0.070 - No. DFN6-A-Board-SD-1.0 ABLIC Inc. 1.570.03 6 1 5 4 2 3 +0.05 0.08 -0.02 0.5 0.480.02 0.20.05 No. PG006-A-P-SD-2.1 TITLE SNT-6A-A-PKG Dimensions No. PG006-A-P-SD-2.1 ANGLE UNIT mm ABLIC Inc. +0.1 o1.5 -0 4.00.1 2.00.05 0.250.05 +0.1 1.850.05 o0.5 -0 4.00.1 0.650.05 3 2 1 4 5 6 Feed direction No. PG006-A-C-SD-2.0 TITLE SNT-6A-A-Carrier Tape No. PG006-A-C-SD-2.0 ANGLE UNIT mm ABLIC Inc. 12.5max. 9.00.3 Enlarged drawing in the central part o130.2 (60) (60) No. PG006-A-R-SD-1.0 SNT-6A-A-Reel TITLE No. PG006-A-R-SD-1.0 ANGLE QTY. UNIT mm ABLIC Inc. 5,000 0.52 1.36 2 0.52 0.2 0.3 1. 2. 1 (0.25 mm min. / 0.30 mm typ.) (1.30 mm ~ 1.40 mm) 0.03 mm SNT 1. Pay attention to the land pattern width (0.25 mm min. / 0.30 mm typ.). 2. Do not widen the land pattern to the center of the package ( 1.30 mm ~ 1.40 mm ). Caution 1. Do not do silkscreen printing and solder printing under the mold resin of the package. 2. The thickness of the solder resist on the wire pattern under the package should be 0.03 mm or less from the land pattern surface. 3. Match the mask aperture size and aperture position with the land pattern. 4. Refer to "SNT Package User's Guide" for details. 1. 2. (0.25 mm min. / 0.30 mm typ.) (1.30 mm ~ 1.40 mm) No. PG006-A-L-SD-4.1 TITLE SNT-6A-A -Land Recommendation No. PG006-A-L-SD-4.1 ANGLE UNIT mm ABLIC Inc. 1.40.05 (0.8) 0.5 0.20.05 The heat sink of back side has different electric potential depending on the product. Confirm specifications of each product. Do not use it as the function of electrode. No. PV006-A-P-SD-2.0 TITLE DFN-6-A-PKG Dimensions PV006-A-P-SD-2.0 No. ANGLE UNIT mm ABLIC Inc. 2.00.05 +0.1 o1.5 -0 +0.1 o0.5 -0 1.60.1 3 1 4 6 4.00.1 0.200.05 4.00.1 0.650.1 Feed direction No. PV006-A-C-SD-1.0 TITLE DFN-6-A-Carrier Tape PV006-A-C-SD-1.0 No. ANGLE UNIT mm ABLIC Inc. +1.0 9.0 - 0.0 11.41.0 Enlarged drawing in the central part o130.2 No. PV006-A-R-SD-1.0 DFN-6-A-Reel TITLE PV006-A-R-SD-1.0 No. QTY. ANGLE UNIT mm ABLIC Inc. 5,000 0.8 0.5 0.2 Caution It is recommended to solder the heat sink to a board in order to ensure the heat radiation. PKG No. PV006-A-L-SD-1.0 TITLE DFN-6-A -Land Recommendation No. PV006-A-L-SD-1.0 ANGLE UNIT mm ABLIC Inc. Disclaimers (Handling Precautions) 1. All the information described herein (product data, specifications, figures, tables, programs, algorithms and application circuit examples, etc.) is current as of publishing date of this document and is subject to change without notice. 2. The circuit examples and the usages described herein are for reference only, and do not guarantee the success of any specific mass-production design. ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the reasons other than the products described herein (hereinafter "the products") or infringement of third-party intellectual property right and any other right due to the use of the information described herein. 3. ABLIC Inc. is not liable for any losses, damages, claims or demands caused by the incorrect information described herein. 4. Be careful to use the products within their ranges described herein. Pay special attention for use to the absolute maximum ratings, operation voltage range and electrical characteristics, etc. ABLIC Inc. is not liable for any losses, damages, claims or demands caused by failures and / or accidents, etc. due to the use of the products outside their specified ranges. 5. Before using the products, confirm their applications, and the laws and regulations of the region or country where they are used and verify suitability, safety and other factors for the intended use. 6. When exporting the products, comply with the Foreign Exchange and Foreign Trade Act and all other export-related laws, and follow the required procedures. 7. The products are strictly prohibited from using, providing or exporting for the purposes of the development of weapons of mass destruction or military use. ABLIC Inc. is not liable for any losses, damages, claims or demands caused by any provision or export to the person or entity who intends to develop, manufacture, use or store nuclear, biological or chemical weapons or missiles, or use any other military purposes. 8. The products are not designed to be used as part of any device or equipment that may affect the human body, human life, or assets (such as medical equipment, disaster prevention systems, security systems, combustion control systems, infrastructure control systems, vehicle equipment, traffic systems, in-vehicle equipment, aviation equipment, aerospace equipment, and nuclear-related equipment), excluding when specified for in-vehicle use or other uses by ABLIC, Inc. Do not apply the products to the above listed devices and equipments. ABLIC Inc. is not liable for any losses, damages, claims or demands caused by unauthorized or unspecified use of the products. 9. In general, semiconductor products may fail or malfunction with some probability. The user of the products should therefore take responsibility to give thorough consideration to safety design including redundancy, fire spread prevention measures, and malfunction prevention to prevent accidents causing injury or death, fires and social damage, etc. that may ensue from the products' failure or malfunction. The entire system in which the products are used must be sufficiently evaluated and judged whether the products are allowed to apply for the system on customer's own responsibility. 10. The products are not designed to be radiation-proof. The necessary radiation measures should be taken in the product design by the customer depending on the intended use. 11. The products do not affect human health under normal use. However, they contain chemical substances and heavy metals and should therefore not be put in the mouth. The fracture surfaces of wafers and chips may be sharp. Be careful when handling these with the bare hands to prevent injuries, etc. 12. When disposing of the products, comply with the laws and ordinances of the country or region where they are used. 13. The information described herein contains copyright information and know-how of ABLIC Inc. The information described herein does not convey any license under any intellectual property rights or any other rights belonging to ABLIC Inc. or a third party. Reproduction or copying of the information from this document or any part of this document described herein for the purpose of disclosing it to a third-party is strictly prohibited without the express permission of ABLIC Inc. 14. For more details on the information described herein or any other questions, please contact ABLIC Inc.'s sales representative. 15. This Disclaimers have been delivered in a text using the Japanese language, which text, despite any translations into the English language and the Chinese language, shall be controlling. 2.4-2019.07 www.ablic.com