VTD3-H25A-12M352 - Vectron International

Vectron International 267 Lowell Road, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

VTD3 series

Voltage Controlled Temperature Compensated Crystal Oscillator

The VTD3, VCTCXO

Features

• CMOS Output

• Output Frequencies to 61.440 MHz

• Fundamental Crystal Design

• Optional VCXO function available

• Product is compliant to RoHS directive

Applications

• Wireless Communications

• Base Stations

• Point to point radios

• Broadband Access

• Test Equipment

Description

Vectron’s VTD3 Temperature Compensated

Crystal Oscillator (TCXO) is a quartz stabilized,

CMOS squarewave, temperature compensated

oscillator, operating off either 3.3 or 5.0 volt

supply.

VTD3 Data sheet

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

Performance Characteristics

Table 1. Electrical Performance

Parameter Symbol Min Typical Maximum Units

Frequency fO 10.000 61.440 MHz

Supply Voltage 3.3V±5%, 5V±5%

Maximum Supply Voltage 7 VDC

Supply Current,

Output Frequency<22MHz

Output Frequency=>22MHz

IDD

15

24

mA

Output Level 2

Logic High

Logic Low

Drive High

Drive Low

VOH

VOL

IOH

IOL

0.9*VDD

4

0.1*VDD

-4

V

mA

Output Load 15pf

Duty Cycle, @ 50% 40/60 %

Control Voltage Impedance ZVc 100 Kohm

Control Voltage to reach pull, 5V option

3.3 V option 0.5

0.3 4.5

3.0 V

Pull Range

Ordering option, see last page TPR ±5, ±8, ±10, ±15 ppm

Temperature Stability

Ordering option, see last page. ±1.0 to ±5.0 ppm

Initial Accuracy, “No Adjust” option ±2.0 ppm

Power Supply Stability ±1.0 ppm

Load Stability ±0.3 ppm

Aging ±1.0 ppm/year

Operating temperature

Ordering option, see last page 0/55, -10/60, -20/70, -30/75, -40/85 °C

Phase Noise, 10.000MHz

10 Hz offset

100 Hz offset

1 kHz offset

10 kHz offset

100 kHz offset

-107

-138

-148

-152

-154

dBc/Hz

Start-up time 10 ms

1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended.

2. Output is DC coupled.

VTD3 Data sheet

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

VCXO Functional Description

VCXO Feature: The VTD3 can be ordered with a VCXO function for applications where it will be used in

a PLL, or the output frequency needs fine tune adjustments. This is high impedance input, 100 kohm, and

can be driven with an op-amp or terminated with adjustable resistors etc. Pin 1 should not be left

floating on the VCXO optional devices.

“No Adjust” Feature: In applications where the VTD3 will not be used in a PLL, or the output frequency

does not need fine tune adjustments, the fixed TCXO/VTD3-x0xx is the best option. By using the “no

adjust” option, the circuit is simplified as Vc does not need to adjusted or set to a predetermined voltage.

Pin 1 can be grounded to reduce the risk of adding noise into the circuit.

Outline Diagrams, Pad Layout and Pin Out

Table 2. Pinout

Pin # Symbol Function

1 N/C or VC No Connect (VTD3-x0xx) or VCXO Control Voltage

2 GND Electrical and Case Ground

3 fO Output Frequency

4 VDD Supply Voltage

Figure 1, Package

drawing and Pad Layout

VTD3-XXXX

2.0 mm

(max)

VTD3

Frequency

Date Code

VTD3 Data sheet

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com

A

E

C

D

B

GFJ

LI

KH

Tape and Reel

Table 3. Tape and Reel Dimensions (mm)

Tape Dimensions Reel Dimensions # Per

Product A B C D E F G H I J K L Reel

VTD3 24 11.5 1.5 4 12 2 21 13 80 2 25.5 255 1K

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional

operation is not implied at these or any other conditions in excess of conditions represented in the

operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may

adversely affect device reliability.

Table 4. Absolute Maximum Ratings

Parameter Symbol Ratings Unit

Storage Temperature Tstorage -40/85 °C

Reliability

The VTD3 qualification tests have included:

Table 5. Environnemental Compliance

Parameter Conditions

Mechanical Shock MIL-STD-883 Method 2002

Mechanical Vibration MIL-STD-883 Method 2007

Temperature Cycle MIL-STD-883 Method 1010

Solderability MIL-STD-883 Method 2003

Gross and Fine Leak MIL-STD-883 Method 1014

Resistance to Solvents MIL-STD-883 Method 2015

Handling Precautions

Although ESD protection circuitry has been designed into the VTD3, proper precautions should be taken

when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for

VTD3 Data Sheet

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail vectron@vectron.com

5

ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit

parameters used to define the model. Although no industry wide standard has been adopted for the CDM,

a standard HBM of resistance = 1.5Kohms and capacitance = 100pF is widely used and therefore can be

used for comparison purposes.

Table 6. ESD Ratings

Model Minimum Conditions

Human Body Model 1000 MIL-STD-883 Method 3015

Charged Device Model 500 JESD 22-C101

Suggested IR profile

Table 7 shows max temperatures and lower peak temperatures can also be used e.g. peak temperature

of 230-240°C. The VTD3 should not be subjected to a wash process that will immerse it in solvents – a

no clean process is recommended.

Table 7. Reflow Profile

Parameter Symbol Value

PreHeat Time t S 60 sec Min, 180 sec Max

Ramp Up R UP 3

oC/sec Max

Time Above 217 oC t L 60 sec Min, 150 sec Max

Time To Peak Temperature t AMB-P 480 sec Max

Time At 260 oC (max) t P 6 sec Max

Time At 240 °C (max) tp2 60 sec Max

Ramp Down R DN 6

oC/sec Max

VTD3 Data Sheet

Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail vectron@vectron.com

6

Ordering Information

Table 8. Standard Frequency List

10.00 11.00 12.288 12.352 12.50 12.80 13.00 14.31818

14.40 15.36 16.384 16.80 19.20 19.44 19.6608 19.68

20.00 26.88 27.00 32.00 32.768 44.00 44.736 50.000

VTD3 - -

Product Family Output Frequency

TCXO, 9.6 x 11.5 In MHz

Voltage Options Temperature Options

H: +5.0 Vdc ±5% A: 0 to 55°C

J: +3.3 Vdc ±5% B: -10 to 60°C

C: -20 to 70°C

Pulling Range D: -30 to 75°C

0: Fixed TCXO, no adjust E: -40 to 85°C

1: ±5ppm

2: ±8ppm Stability Options

3: ±10ppm 1: ±1.0ppm

4: ±15ppm B: ±1.5ppm

2: ±2.0ppm

C: ±2.5ppm

3: ±3.0 ppm

4: ±4.0ppm

5: ±5.0ppm

Note: Not all combinations are availabl e

www.vectron.com

September 23 2009

For Additional Information, Please Contact:

USA: Vectron International • 267 Lowell Road, Hudson, NH 03051

• Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON

EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany •

Tel: 49 (0) 7268 8010 • Fax: 49 (0) 7268 801281

ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd.,

WaiGaoQiao Free Trade Zone, Pudong New Area Shanghai, China 200131

•Tel: 8621 50480777 • Fax: 8621 50481881

J 0 C 10M00

2