150 Watts LPQ150 Series Total Power: 110-150 Watts Input Voltage: 85-132 / 170-264 VAC 220-300 VDC # of Outputs: Quad Electrical Specs Input Input range 85-132 VAC or 170-264 VAC automatically selected. 220-300 VDC 47-63 Hz 38 A max, cold start @ 25C 75% typical at full load Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted Frequency Inrush current Efficiency EMI filter Safety ground leakage current Special Features * * * * * * * * * * * Auto ranging input Remote sense on main output Remote inhibit Single wire current sharing Power fail Built-in EMI filter Low output ripple 135 khz switching frequency Overvoltage protection Overload protection Adjustable floating 4th output (On LPQ152 and LPQ153 models) * Optional cover (-C suffix). See page 64. Environmental Output Maximum power Adjustment range Cross regulation Hold-up time Overload protection Overvoltage protection Power failure Remote inhibit Electromagnetic susceptibility: designed to meet IEC 801, -2, -3, -4, -5, -6, Level 3 Remote sense Humidity: Operating; non-condensing 5% to 95% Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75 G peak 5 Hz to 500 Hz, operational Temperature coefficient: .04% per C MTBF demonstrated: >550,000 hours at full load and 25C ambient condition TTL logic signal goes high 50-150 msec after 5 V output. It goes low at least 3 msec before loss of regulation Requires an external TTL high signal to inhibit outputs Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. Safety VDE UL CSA NEMKO CB CE 114 110 W convection (75 W with cover) 150 W with 30 CFM forced air (130 W with cover) 5% on main; 5-25 V on 4th output on LPQ 152 & LPQ 153 2% on output 1; 3% on outputs 2, 3 &4 20 ms @110 W load at nominal line Short circuit protection on all outputs. Case overload protected @ 110-145% above peak rating 5.7-6.7 VDC on main output Logic Control Operating temperature: 0 to 50C ambient derate each output at 2.5% per degree from 50 to 70C Storage temperature: -40 to 85C 0.5 mA @ 50/60 Hz, 264 VAC input 0805/EN60950 (IEC950) UL1950 CSA 22.2-234 Level 3 EN 60950/EMKO-TUE (74-sec) 203 Certificate and report Mark (LVD) 11774-3336-1260 (LC# 88585) EI32002 LR53982 P95102999 2061 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 rev 12.10.03 AMERICAS EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 LPQ150 Series Ordering Information Regulation2 Model Output Minimum Maximum Load with Maximum Load with Peak Number Voltage Load Convection Cooling 30 CFM Forced Air Load1 LPQ152 5V 12 V -12 V 5-25 V 2A .1 A .1 A 0A 15 A 6A 2A 2.5 A 22 A 8A 2.5 A 3A 30 A 10 A 3A 3A 2% 3% 3% 3% 50 mV 120 mV 120 mV 240 mV, max. LPQ153 5V 15 V -15 V 5-25 V 2A .1 A .1 A 0A 15 A 4.8 A 1.6 A 2.5 A 22 A 6.4 A 2A 3A 30 A 8A 2.4 A 3A 2% 3% 3% 3% 50 mV 150 mV 150 mV 240 mV, max. LPQ154 5V 12 V -12 V 24 V 2A .1 A .1 A .5 A 15 A 6A 2A 3.5 A 22 A 8A 2.5 A 4.5 A 30 A 10 A 3A 5A 2% 3% 3% +10 / -5% 50 mV 120 mV 120 mV 240 mV 1. 2. 3. 4. 5. Ripple P/P (PARD)3 Peak current lasting <30 seconds with a maximum 10% duty cycle. At 25C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor at rated line voltage and load ranges. 4th output adjustable 5-25 V factory set at 5 V. Minimum loads are required. SK3 LPQ152 INHIBIT -ve INHIBIT +ve +12 V No Connection COMMON -SENSE +SENSE LPQ153 INHIBIT -ve INHIBIT +ve +15 V No Connection COMMON -SENSE +SENSE LPQ154 INHIBIT -ve INHIBIT +ve +12 V No Connection COMMON -SENSE +SENSE PIN 8 SK2 PIN 1,2 PIN 3,4,5 PIN 6 PIN 7 PIN 8 I SHARE +12 V COMMON -12 V POK +5 V to +25 V (Float) I SHARE +15 V COMMON -15 V POK +5 V to +25 V (Float) I SHARE +12 V COMMON -12 V POK +24 V PIN 9 SK3 TB-1 COMMON (Float) COMMON COMMON (Float) COMMON COMMON COMMON TB-2 SK4 PIN 1 PIN 3 PIN 5 +5 V GROUND LINE NEUTRAL +5 V GROUND LINE NEUTRAL +5 V GROUND LINE NEUTRAL Mating Connectors (SK4) AC Input: Molex 09-50-8051 (USA) Molex 09-91-0500 (UK) PINS: 08-58-0111 (SK2) Aux DC Output/Power fail: Molex 09-50-8091 (USA) Molex 09-91-0900 (UK) PINS: 08-58-0111 (SK1) Remote sense/Remote inhibit: Molex 51110-0851 (USA) PINS: 503-94-8100 2 1 SK2 #6-32 UNC (8 places) 1234 .5625 987654321 4th O/P ADJ Connector SK1 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 SK1 8765 5V O/P ADJ Pin Assignments DO NOT ADJ Note: -C suffix added to the model number indicates cover option. 7.4 (188.0) 8.5 (216.0) Notes 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is 0.02". 3. Specifications are for convection rating at factory settings unless otherwise stated. 4. Remote inhibit requires an external 5V @ 10mA to activate. 5. Mounting (6-32) maximum insertion depth is 0.12". 6. Warranty: 1 year 7. Weight: 1.75 lb. / 0.80 kg 531 SK4 4.25 (108.0) .875 (22.25) .75 (19.0) 1.5 (38.1) 2.5 (63.5) Astec Connector Kit #70-841-010, includes al of the above. www.astecpower.com 115