Spatter-resistant Proximity Sensor E2EQ CSM_E2EQ_DS_E_7_1 Spatter-resistant Fluororesincoated Proximity Sensor * Superior spatter resistance. * Long Sensing-distance Models added for sensing distances up to 15 mm. * Pre-wired Smartclick Connector Models are also available. For the most recent information on models that have been certified for safety standards, refer to your OMRON website. Be sure to read Safety Precautions on page 6. Ordering Information Sensors [Refer to Dimensions on page 7.] Pre-wired Models Long Sensing-distance Models Appearance M12 Shielded M18 Sensing distance Output configuration Operation mode 4 mm 8 mm M30 Model E2EQ-X4X1 2M DC 2-wire (no polarity) NO E2EQ-X8X1 2M E2EQ-X15X1 2M 15 mm Standard Models Appearance M12 Shielded M18 M30 Sensing distance Output configuration Operation mode Model E2EQ-X3D1 2M 3 mm DC 2-wire 7 mm NO E2EQ-X7D1 2M E2EQ-X10D1 2M 10 mm Pre-wired Smartclick Connector Models (M12) Long Sensing-distance Models Appearance M12 Sensing distance 4 mm Shielded M18 8 mm M30 15 mm Output configuration DC 2-wire (no polarity) (3)-(4) pin arrangement Operation mode Model E2EQ-X4X1-M1TJ 0.3M NO E2EQ-X8X1-M1TJ 0.3M E2EQ-X15X1-M1TJ 0.3M Standard Models Standard Models M12 Sensing distance M30 Operation mode 7 mm 10 mm Model E2EQ-X3D1-M1TGJ 0.3M 3 mm Shielded M18 Output configuration DC 2-wire (1)-(4) pin arrangement NO E2EQ-X7D1-M1TGJ 0.3M E2EQ-X10D1-M1TGJ 0.3M 1 E2EQ Pre-wired Connector Models (M12) Long Sensing-distance Models Appearance Sensing distance M12 Shielded 4 mm M18 8 mm M30 15 mm Output configuration Operation mode Model E2EQ-X4X1-M1J 0.3M DC 2-wire (without polarity) (3)-(4) pin arrangement NO E2EQ-X8X1-M1J 0.3M E2EQ-X15X1-M1J 0.3M Standard Models Standard Models M12 Shielded Sensing distance DC 2-wire (1)-(4) pin arrangement 7 mm M30 Operation mode Model E2EQ-X3D1-M1GJ 0.3M 3 mm M18 Output configuration NO E2EQ-X7D1-M1GJ 0.3M E2EQ-X10D1-M1GJ 0.3M 10 mm Accessories (Order Separately) Sensor I/O Connectors (M12, Sockets on One Cable End) (Models with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) [Refer to XS2, XS5.] Appearance Cable length Sensor I/O Connector model number 2m XS2F-D421-DC0-F 5m XS2F-D421-GC0-F L-shape 2m 5m XS2F-D422-DC0-F XS2F-D422-GC0-F Straight 2m XS2F-D421-DA0-F 5m XS2F-D421-GA0-F L-shape 2m 5m XS2F-D422-DA0-F XS2F-D422-GA0-F Smartclick Connector Straight 2m XS5F-D421-D80-F 5m XS5F-D421-G80-F Straight Applicable Proximity Sensor model number E2EQ-X@X1-M1J E2EQ-X@D1-M1GJ E2EQ-X@X1-M1TJ E2EQ-X@D1-M1TGJ Note: Refer to Introduction to Sensor I/O Connectors/Sensor Controllers for details. Ratings and Specifications Long Sensing-distance Models Model E2EQ-X4X1 E2EQ-X4X1-M1(T)J Item E2EQ-X8X1 E2EQ-X8X1-M1(T)J E2EQ-X15X1 E2EQ-X15X1-M1(T)J Sensing distance 4 mm 10% 8 mm 10% 15 mm 10% Set distance *1 0 to 3.2 mm 0 to 6.4 mm 0 to 12 mm Differential travel 15% max. of sensing distance Standard sensing object Iron, 12 12 1 mm Iron, 18 18 1 mm Iron, 30 30 1 mm Response frequency *2 1 kHz 0.5 kHz 0.25 kHz Control output Load current 3 to 100 mA Residual voltage *3 5 V max. (Load current: 100 mA, Cable length: 2 m) Operation mode (with sensing object approaching) Load ON: NO; For details, refer to the timing charts on page 5. Protection circuits Load short-circuit protection, Surge suppressor Ambient temperature range Operating: 25 to 70C, Storage: 40 to 85C, (with no icing or condensation) Temperature influence 15% max. of sensing distance at 23C in the temperature range of 40 to 85C 10% max. of sensing distance at 23C in the temperature range of 25 to 70C Voltage influence 1% max. of sensing distance at rated voltage in the rated voltage 15% range Shock resistance Destruction: 1,000m/s2 10 times each in X, Y, and Z directions Connection method Weight (packed state) 15% max. of sensing distance at 23C in the temperature range of 25 to 70C Pre-wired Models (Standard cable length: 2 m), Pre-wired Connector Models Pre-wired Models Approx. 65 g Approx. 140 g Approx. 190 g Pre-wired Connector Models Approx. 20 g Approx. 40 g Approx. 90 g *1. Use the Sensor within the range in which the green indicator is ON. *2. The response frequency is an average value. *3. The residual voltage is 5 V. Make sure that the device connected to the Sensor can withstand the residual voltage. 2 E2EQ Standard Models Model E2EQ-X3D1 E2EQ-X3D1-M1(T)GJ Item E2EQ-X7D1 E2EQ-X7D1-M1(T)GJ E2EQ-X10D1 E2EQ-X10D1-M1(T)GJ Sensing distance 3 mm 10% 7 mm 10% 10 mm 10% Set distance 0 to 2.4 mm 0 to 5.6 mm 0 to 8 mm Differential travel 10% max. of sensing distance Standard sensing object Iron, 12 x 12 x 1 mm Iron, 18 x 18 x 1 mm Iron, 30 x 30 x 1 mm 1 kHz 500 Hz 400 Hz Response frequency * Control output Load current 3 to 100 mA Residual voltage 3 V max. (Load current: 100 mA, Cable length: 2 m) Operation mode (with sensing object approaching) Load ON: NO; For details, refer to the timing charts on page 5. Protection circuits Load short-circuit protection, Surge suppressor Ambient temperature range Operating/Storage: -25 to 70C (with no icing or condensation) Temperature influence 10% max. of sensing distance at 23C in the temperature range of -25 to 70C Voltage influence 2.5% max. of sensing distance at rated voltage in the rated voltage 15% range Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions Connection method E2EQ-X@D1: Pre-wired Models (Standard cable length: 2 m) E2EQ-X@D1-M1GJ: Pre-wired Connector Models (Standard cable length: 300mm) Weight (packed state) Pre-wired Models Approx. 120 g Pre-wired Approx. 80 g Connector Models Approx. 160 g Approx. 220 g Approx. 110 g Approx. 190 g * The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. Common Ratings and Performance Model Item E2EQ-X4X1 E2EQ-X4X1-M1(T)J E2EQ-X3D1 E2EQ-X3D1-M1(T)GJ E2EQ-X8X1 E2EQ-X8X1-M1(T)J E2EQ-X7D1 E2EQ-X7D1-M1(T)GJ E2EQ-X15X1 E2EQ-X15X1-M1(T)J E2EQ-X10D1 E2EQ-X10D1-M1(T)GJ Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 4.) Power supply voltage (operating voltage range) 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. Leakage current 0.8 mA max. Indicators Operation indicator (red), Setting indicator (green) Ambient humidity range Operating/Storage: 35% to 95% (with no condensation) Insulation resistance 50 M min. (at 500 VDC) between current-carrying parts and case Dielectric strength 1,000 VAC for 1 min between current-carrying parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Degree of protection IEC 60529 IP67, in-house standards: oil-resistant Materials Case Fluororesin coating (Base material: brass) Sensing surface Fluororesin Clamping nuts Fluororesin coating (Base material: brass) Toothed washer Accessories Zinc-plated iron Instruction manual 3 E2EQ Engineering Data (Reference Value) Sensing Area Distance X (mm) Distance X (mm) E2EQ-X@X@(-M1(T)J) Shielded Models E2EQ-X@D@(-M1(T)GJ) 18 16 E2EQ-X15X 14 10 E2EQ-X10D1 8 12 E2EQ-X8X 10 6 E2EQ-X4X 6 E2EQ-X7D1 E2EQ-X3D1 8 4 Y Y X 4 X 2 2 0 -20 -15 -10 -5 0 5 10 15 -20 -16 -12 20 Distance Y (mm) -8 -4 0 4 8 12 16 20 Distance Y (mm) E2EQ-X3D1 Sensing Head E2EQ-X7D1 Sensing Head E2EQ-X10D1 Sensing Head Influence of Sensing Object Size and Material dx d X E2EQ-X8X1(-M1(T)J) t = 1 mm 4 Iron Stainless steel (SUS304) 10 dx d X E2EQ-X15X1(-M1(T)J) t = 1 mm 8 3 Iron 6 2 20 25 30 35 0 10 Brass Aluminum 40 X t = 1 mm Iron Stainless steel (SUS304) 2.5 0 50 10 20 9 Brass X t = 1 mm dx d 12 8 Copper 0.5 60 X 70 80 t = 1 mm 10 7 Iron Iron 6 8 Stainless steel (SUS304) 4 Stainless steel (SUS304) 6 Brass 3 1.0 50 14 dx d Aluminum 1.5 40 E2EQ-X10D1(-M1(T)GJ) 5 2.0 30 Side length of sensing object: d (mm) Distance X (mm) dx d 3.0 0 30 10 Distance X (mm) 3.5 20 Copper Side length of sensing object: d (mm) E2EQ-X7D1(-M1(T)GJ) 4.0 Iron 4 Side length of sensing object: d (mm) E2EQ-X3D1(-M1(T)GJ) 16 8 2 15 t = 1 mm Copper 1 10 X Stainless steel (SUS304) Brass 4 5 dx d 12 Copper 0 20 Stainless steel (SUS304) Brass Distance X (mm) Distance X (mm) 5 Distance X (mm) Distance X (mm) E2EQ-X4X1(-M1(T)J) Aluminum 2 Copper Brass 4 Aluminum 2 Copper 1 5 10 15 20 25 30 35 Side length of sensing object: d (mm) 0 5 10 15 20 25 30 35 40 45 Side length of sensing object: d (mm) 0 5 10 15 20 25 30 35 40 45 50 55 Side length of sensing object: d (mm) 4 E2EQ Residual Output Voltage Leakage Current E2EQ-X@D@(-M1(T)GJ) 4 3 2 E2EQ-X@D 5 Leakage current (mA) 5 Residual output voltage (V) Residual output voltage (V) E2EQ-X@X@(-M1(T)J) 4 3 1.5 1.0 E2EQ-X3D1 2 0.5 1 1 E2EQ-X10D1 E2EQ-X7D1 0 1 3 5 10 30 50 100 0 1 3 5 10 30 50 100 300 500 1,000 Load current (mA) Load current (mA) 0 10 20 30 40 Power supply voltage (V) I/O Circuit Diagrams Long Sensing-distance Models Model Operation mode Timing Chart Output circuit 4 Unstable sensing Non-sensing area area E2EQ-X4X1 E2EQ-X8X1 E2EQ-X15X1 E2EQ-X4X1-M1(T)J E2EQ-X8X1-M1(T)J E2EQ-X15X1-M1(T)J Set position (%) 3 100 Rated sensing distance 80 (TYP) +V Proximity Sensor main circuit Stable sensing area Sensing object NO Brown Load 0 ON Setting indicator OFF (green) 0V Note 1. The load can be connected to either the +V or 0 V side. Note 2. There is no polarity. Therefore, the brown and blue lines have no polarity. Connector Pin Arrangement Operation indicator OFF (red) ON ON Blue 1 Control output 2 OFF 4 3 Note: Pins 1 and 2 are not used. Standard Models Model Operation mode Timing Chart Output circuit Brown Non-sensing area Unstable Set position sensing Stable sensing area area Proximity Sensor Sensing object E2EQ-X3D1 E2EQ-X7D1 E2EQ-X10D1 E2EQ-X3D1-M1(T)GJ E2EQ-X7D1-M1(T)GJ E2EQ-X10D1-M1(T)GJ Load 1 Blue 4 (%) NO 100 Rated sensing distance 80 (TYP) 0 +V Proximity Sensor main circuit 0V Note: The load can be connected to either the +V or 0 V side. ON Setting indicator OFF (green) Connector Pin Arrangement ON Operation OFF indicator (red) 1 2 ON Control output 4 3 OFF Note: Pins 2 and 3 are not used. 5 E2EQ Pre-wired Connector Model Connections Model E2EQ-X@X1-M1(T)J E2EQ-X@D1-M1(T)GJ Pre-wired Connector Model E2EQ-X@D1-M1GJ Sensor I/O Connector XS2F-D42@-@C0-F Pre-wired Connector Model E2EQ-X@X1-M1J 1 2 2 3 3 4 4 Brown (not used) Main circuit Main circuit 1 Blue (-) Black (+) Sensor I/O Connector XS2F-D42@-@A0-F 1 1 2 2 3 3 4 4 Brown (+) Blue (-) Connections Pre-wired Connector Sensor I/O Connector Model XS5F-D421-@80-F E2EQ-X@D1-M1TGJ Sensor I/O Connector XS5F-D421-@80-F Pre-wired Connector Model E2EQ-X@X1-M1TJ 1 2 2 3 3 4 4 Brown (not used) White (not used) Blue (-) Black (+) Main circuit Main circuit 1 1 1 2 2 3 3 4 4 Brown (+) White (not used) Blue (not used) Black (-) Safety Precautions Refer to Warranty and Limitations of Liability. Mutual Interference WARNING When installing two or more Sensors face-to-face or side-by-side, ensure that the minimum distances given in the following table are maintained. This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. B A Precautions for Correct Use Do not use this product under ambient conditions that exceed the ratings. Mutual Interference (Unit: mm) Model Item Design Influence of Surrounding Metal E2EQ-X4X1(-M1(T)J) When mounting the Sensor within a metal panel, ensure that the clearances given in the following table are maintained. Failure to maintain these distances may cause deterioration in the performance of the Sensor. A B 30 20 E2EQ-X8X1(-M1(T)J) 60 35 E2EQ-X15X1(-M1(T)J) 110 90 E2EQ-X3D1(-M1(T)GJ) 30 20 E2EQ-X7D1(-M1(T)GJ) 50 35 E2EQ-X10D1(-M1(T)GJ) 100 70 Mounting l Do not tighten the nut with excessive force. A washer must be used with the nut. n m d dia. D m Shielded Model l Influence of Surrounding Metal (Unit: mm) Model l d D m n E2EQ-X4X1(-M1(T)J) Item 2.4 18 2.4 12 18 E2EQ-X8X1(-M1(T)J) 3.6 27 3.6 24 27 E2EQ-X15X1(-M1(T)J) 6 45 6 45 45 8 18 0 20 27 40 45 E2EQ-X3D1(-M1(T)GJ) E2EQ-X7D1(-M1(T)GJ) E2EQ-X10D1(-M1(T)GJ) 12 0 18 30 Part B Part A Note: 1. The allowable tightening strength depends on the distance from the edge of the head, as shown in the following table. (A is the distance from the edge of the head. B includes the nut on the head side. If the edge of the nut is in part A, the tightening torque for part A applies instead.) 2. The following torque assume washers are being used. Torque Model Part A Dimension (mm) Part B Torque E2EQ-X4X1(-M1(T)J) E2EQ-X8X1(-M1(T)J) Torque 30 N*m 70 N*m --- E2EQ-X15X1(-M1(T)J) 180 N*m E2EQ-X3D1(-M1(T)GJ) 24 E2EQ-X7D1(-M1(T)GJ) 29 E2EQ-X10D1(-M1(T)GJ) 26 15 N*m --- 39 N*m 78 N*m 6 E2EQ (Unit: mm) Dimensions Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified. Pre-wired Models Long Sensing-distance Models E2EQ-X4X1 38 33 21 dia. 17 4 9 10 2 *1 Indicators *2 Two clamping nuts Toothed washer M12 x 1 *1. 4-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant, Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. Operation indicator (red), Setting indicator (green) E2EQ-X15X1 E2EQ-X8X1 43 38 29 dia. 24 48 43 42 dia. 36 12 10 3 5 10 2 4 12 *1 *1 Indicators *2 Indicators *2 Two clamping nuts M18 x 1 M30 x 1.5 Toothed washer Two clamping nuts Toothed washer *1. 6-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. Operation indicator (red), Setting indicator (green) *1. 6-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. Operation indicator (red), Setting indicator (green) Standard Models E2EQ-X3D1 38 27.6 24 21 dia. 17 5 M12 x 1 Indicators *2 *1 Two clamping nuts (fluororesin coated) Two toothed washers 4 *1. 6-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. Operation indicator (red), Setting indicator (green) E2EQ-X7D1 E2EQ-X10D1 47 29 dia. 32 24 56 42 dia. 36 29 42 38 10 6 M18 x 1 4 *1 Indicators *2 Two clamping nuts (fluororesin coated) Two toothed washers *1. 6-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. Operation indicator (red), Setting indicator (green) *1 Indicators *2 M30 x 1.5 5 Two clamping nuts (fluororesin coated) Two toothed washers *1. 6-dia. vinyl-insulated round cable with 2 conductors (Flame-resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. Operation indicator (red), Setting indicator (green) 7 E2EQ Pre-wired Connector Models Long Sensing-distance Models E2EQ-X4X1-M1(T)J 38 33 21 dia. 17 9 10 2 4 1* Indicators *2 M12 x 1 Toothed washer M12 x 1 Two clamping nuts *1. 4-dia. vinyl-insulated round cable (Flame-resistant, Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm), Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) E2EQ-X8X1-M1(T)J E2EQ-X15X1-M1(T)J 43 38 29 dia. 24 4 48 43 42 dia. 36 12 12 5 10 3 10 2 Indicators *2 M18 x 1 *1 1* M12 x 1 Indicators *2 M12 x 1 M30 x 1.5 Toothed Two clamping nuts washer *1. 6-dia. vinyl-insulated round cable (Flame-resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) Toothed Two clamping nuts washer *1. 6-dia. vinyl-insulated round cable (Flame-resistant, Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) Standard Models E2EQ-X3D1-M1(T)GJ 38 27.6 24 5 21 dia. 17 *1. 6-dia. vinyl-insulated round cable (flame-resistant), Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) Indicators *2 M12 x 1 E2EQ-X7D1-M1(T)GJ 32 29 *1. 6-dia. vinyl-insulated round cable (flameresistant), Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) 6 4 M12 x 1 (aluminum) *1. 6-dia. vinyl-insulated round cable (flame-resistant), Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) 56 42 dia. 36 42 38 10 M12 x 1 (aluminum) M12 x 1 (aluminum) Indicators *2 M18 x 1 *1 Two clamping nuts (fluororesin coated) Two toothed washers E2EQ-X10D1-M1(T)GJ 47 29 dia. 24 4 *1 Indicators*2 *1 Two clamping nuts (fluororesin coated) Two toothed washers Mounting Hole Dimensions M30 x 1.5 Model E2EQ-X4X@ E2EQ-X3@ F (mm) 12.5 0 +0.5 5 dia. Two clamping nuts (fluororesin coated) Two toothed washers E2EQ-X8X@ E2EQ-X7@ +0.5 18.5 0 dia. E2EQ-X15X@ E2EQ-X10@ +0.5 30.5 0 dia. F 8 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron's exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron's sole obligation hereunder shall be, at Omron's election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron's analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer's application or use of the Product. At Buyer's request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer's application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user's programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron's test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron's Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron's representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2014.1 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2014 All Right Reserved. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Omron: E2EQ-X10D1G-M1GJ-T 0.3M E2EQ-X10D1-M1J-1 0.3M E2EQ-X10D2R-M1GJ-T4 0.3M E2EQ-X15X1 2M E2EQX3D1G-M1GJ-T 0.3M E2EQ-X3D1-M1J-1 E2EQ-X7D1G-M1GJ-T 0.3M E2EQ-X15X1 5M E2EQ-X3D1-M1J 0.3M E2EQ-X7D1-M1J 0.3M E2EQ-X10D1G-M1TGJ-T-US 0.3M E2EQ-X10D2R-M1TGJ-T4-US 0.3M E2EQ-X3D1GM1TGJ-T-US 0.3M E2EQ-X7D1G-M1TGJ-T-US 0.3M E2EQ-X7D1-M1J-1 0.3M E2EQ-X3D1G-M1TGJ-T 0.3M