UWR Series www.murata-ps.com Single Output, High Reliability, 2" x 1", 6-10 Watt, DC-DC Converters FEATURES Low Cost! Highly reliable! Proven SMT-on-pcb construction PRODUCT OVERVIEW Designed to meet UL/EN/IEC 60950-1, CAN/CSA-C22.2 60950-1 Qual tested; HALT tested; EMC tested Placing reliability and cost considerations above all others, Murata Power Solutions' new A-Series DC/ DC Converters combine straightforward circuit topologies, the newest components, proven SMT-on-pcb construction, and highly repeatable automatic assembly techniques. Considering the critical low-cost and long-term-reliability requirements of today's telecom, datacom and computer/networking applications, the A-Series may well be the most cost-effective DC/DC's available today. The single-output, 6-10 Watt Models of the A-Series deliver both high power densities and impressive MTBF's. Their superior durability is substantiated by a rigorous in-house qualification program including HALT (Highly Accelerated Life Testing). The goal of HALT is not to simulate field conditions but to expose devices to multiple excessive stresses with Small packages, 2" x 1" x 0.375" Standard pinouts 5, 5.2, 12 or 15 Volt outputs Choice of 3 wide-range inputs: 4.7-7.25 Volts 9-18 Volts 18-75 Volts Fully isolated, 1500Vdc guaranteed -40 to +100C operation 5-side metal shielded cases with nonconductive baseplates Modifications and customs for OEMs the intention of precipitating any potential electrical, mechanical or process weaknesses. Packaged in 2" x 1" x 0.375" shielded metal cases with non-conductive coatings, these fully isolated (1500Vdc guaranteed) DC/DC's offer excellent line/load regulation, full I/O protection, and industrystandard pinouts. Output voltages include 5, 5.2, 12 and 15 Volts. Input voltage ranges are either 4.7-7.25V ("D5A" models), 9-18V ("D12A" models) or 18-75V ("D48A" models). All A-Series UWR models are fully EMI characterized and agency safety approved. A-Series DC/DC's are extremely reliable, easyto-use, cost-effective power converters. Use them to improve the reliability of existing equipment or to develop new systems that exceed design objectives. +VOUT (3) +VIN (1) COMMON (5) Typical topology is shown -VIN (2) PWM CONTROLLER OPTO ISOLATION REFERENCE & ERROR AMP Figure 1. Simplified Schematic For full details go to www.murata-ps.com/rohs www.murata-ps.com/support MDC_UWR6-10W Series.E01 Page 1 of 6 UWR Series Single Output, High Reliability, 2" x 1", 6-10 Watt, DC-DC Converters Performance Specifications and Ordering Guide Output Root Model UWR-5/1600-D5A-C UWR-5/2000-D24E-C UWR-5.2/1500-D5A-C UWR-12/665-D5A-C UWR-12/830-D12A-C UWR-5/1800-D48A-C UWR-5/2000-D12A-C UWR-5/2000-D48E-C UWR-12/750-D48A-C UWR-15/530-D5A-C UWR-15/600-D48A-C UWR-15/665-D12A-C Input VOUT * (Volts) IOUT (mA) 5 5 5.2 12 12 5 5 5 12 15 15 15 1600 2000 1500 665 830 1800 2000 2000 750 530 600 665 R/N (mVp-p) Typ. Max. 50 50 50 75 75 75 50 50 75 50 75 75 Regulation (Max.) Line Load 100 75 100 100 100 100 75 75 100 100 100 100 0.2% 0.2% 0.2% 0.2% 0.2% 0.1% 0.2% 0.2% 0.2% 0.2% 0.2% 0.2% Range (Volts) IIN (mA) 5 24 5 5 12 48 12 48 48 5 48 12 4.7-7.25 18-36 4.7-7.25 4.7-7.25 9-18 18-75 9-18 36-72 18-75 4.7-7.25 18-75 9-18 20/2105 10/490 20/2053 25/2046 35/988 10/193 15/1029 10/248 10/230 40/2065 10/233 35/978 0.5% 0.5% 0.5% 0.5% 0.5% 0.25% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% Package (Case, Pinout) Efficiency Min. Typ. VIN Nom. (Volts) 74% 83% 74% 75% 81% 81% 79.5% 82% 81.5% 75% 81.5% 82% 76% 85% 76% 78% 84% 83% 81% 84% 82.5% 77% 84% 85% C2, P11 C2, P11 C2, P11 C2, P11 C2, P11 C2, P11 C2, P11 C2, P11 C2, P11 C2, P11 C2, P11 C2, P11 Typical at TA = +25C under nominal line voltage and full-load conditions unless otherwise noted. Ripple/Noise (R/N) measured over a 20MHz bandwidth. 10% to 100% load. Nominal line voltage, no-load/full-load conditions. See Technical Notes for an explanation of trading off input voltage ranges for higher full-power operating temperature. Please see the Part Number Structure for complete ordering options. PART NUMBER STR UCTURE MECHANICAL SPECIFICATIONS U WR - 5 / 1800 - D48 A - C RoHS-6 hazardous substance compliant Output Configuration: U = Unipolar A-Series High Reliability Wide Range Input 2.00 (50.8) METAL CASE Case C2 0.375 (9.5) INSULATED BASE Input Voltage Range: D5 = 4.7-7.25 Volts (5V nominal) D12 = 9-18 Volts (12V nominal) D24 = 18-36 Volts (24V nominal) D48 = 18-75/36-72 Volts (48V nominal) Nominal Output Voltage: 5, 5.2, 12 or 15 Volts Maximum Output Current in mA Note: Some model number combinations may not be available. Contact Murata Power Solutions for further information. 0.040 0.002 DIA. (1.016 0.051) 0.20 MIN (5.1) 0.800 (20.3) 0.60 (15.24) 3 1 1.00 (25.4) D, E 8 B 0.200 (5.08) C BOTTOM VIEW A Output Power (Watts) I/O Connections E Pin 1 2 3 4 5 6 UWR-5/1600-D5A UWR-5/1800-D48A UWR-5/2000-D12A UWR-5/2000-D24E UWR-5/2000-D48E UWR-5.2/1500-D5A UWR-12/665-D5A UWR-12/750-D48A UWR-12/830-D12A UWR-15/530-D5A UWR-15/600-D48A UWR-15/665-D12A 4 3 2 1 B D C A A B B E C B E C 0 40 45 50 55 Function P11 +Vin -Vin +Vout No Pin Common Notes: Dimensions are in inches (mm) shown for ref. only. Third Angle Projection Tolerances (unless otherwise specified): .XX 0.02 (0.5) .XXX 0.010 (0.25) Angles 2 Components are shown for reference only. For "D5A, D12A and D24E" models, the case is connected to pin 2 (-VIN). 0 -40 0.10 (2.54) D 7 5 0.400 (10.16) 5 A, C 9 0.800 (20.32) 2 TEMPERATURE DERATING 10 0.100 (2.54) 4 60 65 70 75 80 85 90 95 100 For "D48A and D48E" models, the case is connected to pin 1 (+VIN). Ambient Temperature (C) www.murata-ps.com/support MDC_UWR6-10W Series.E01 Page 2 of 6 UWR Series Single Output, High Reliability, 2" x 1", 6-10 Watt, DC-DC Converters Performance/Functional Specifications Typical @ TA = +25C under nominal line voltage and full-load conditions, unless noted. Input Absolute Maximum Ratings Input Voltage Range: D5A Models D12A Models D24E Models D48A Models D48E Models 4.7-7.25 Volts (5V nominal) 9-18 Volts (12V nominal) 18-36Volts (24V nominal 18-75 Volts (48V nominal) 36-72 Volts (48V nominal) Input Voltage: D5A Models D12A Models D24E Models D48A and D48E Models Input Current See Ordering Guide Input Reverse-Polarity Protection Input Filter Type Pi Overvoltage Shutdown: D5A Models D12A Models D24E Models D48A and D48E Models None 20 Volts 40 Volts 76 Volts Reverse-Polarity Protection Yes (Instantaneous, 6A maximum) Output VOUT Accuracy (50% load) 1%, maximum Temperature Coefficient 0.02% per C Ripple/Noise (20MHz BW) See Ordering Guide Line/Load Regulation See Ordering Guide Efficiency See Ordering Guide Isolation Voltage 1500Vdc, guaranteed Isolation Capacitance 250pF Current Limiting Auto-recovery Overvoltage Protection Zener/transorb clamp, magnetic feedback Dynamic Characteristics Current must be <6A. Brief duration only. Fusing recommended. 6.8 Volts, limited duration 15 Volts, limited duration 18 Volts, limited duration Output Current Current limited. Max. current and short-circuit duration model dependent. Storage Temperature -40 to +105C These are stress ratings. Exposure of devices to greater than any of these conditions may adversely affect long-term reliability. Proper operation under conditions other than those listed in the Performance/Functional Specifications Table is not implied. TECHNICAL NOTES Floating Outputs Transient Response (50% load step) 200sec max. to 1.5% of final value Switching Frequency 165kHz (15kHz) Flammability UL94V-0 Environmental Operating Temperature (Ambient): Without Derating With Derating -40 to +60/65/70C (Model dependent) to +100C (See Derating Curves) Storage Temperature -40 to +105C Physical Dimensions 2" x 1" x 0.375" (51 x 25 x 9.5mm) Shielding 5-sided Case Connection: D5A, D12A and D24E Models D48A and D48E Models Pin 2 (-VIN) Pin 1 (+VIN) Case Material Output Overvoltage Protection 5/5.2V Outputs 12V Outputs 15V Outputs 10 Volts 22 Volts 44 Volts 80 Volts Corrosion resistant steel with non-conductive, epoxy-based, black enamel finish and plastic baseplate Pin Material Gold plate over copper alloy Weight 1.3 ounces (37 grams) These power converters require a minimum 10% loading to maintain specified regulation. Operation under no-load conditions will not damage these devices; however they may not meet all listed specifications. Application-specific input/output filtering can be recommended and perhaps added internally upon request for scheduled, quantity orders. Contact Murata Power Solutions Applications Engineering for details. Devices can be screened or modified for higher guaranteed isolation voltages. Contact Murata Power Solutions Applications Engineering for details. Except for 3.3V devices which have no protection. Since these are isolated DC/DC converters, their outputs are "floating." Designers will usually use the output Common (pin 5) as the ground/return of the load circuit. You can, however, use the +Output (pin 3) as ground/ return to effectively reverse the output polarity. Filtering and Noise Reduction All A-Series UWR 6-10 Watt DC/DC Converters achieve their rated ripple and noise specifications without the use of external input/output capacitors. In critical applications, input/output ripple and noise may be further reduced by installing electrolytic capacitors across the input terminals and/ or low-ESR tantalum or electrolytic capacitors across the output terminals. The caps should be located as close to the power converters as possible. Typical values are listed in the tables below. In many applications, using values greater than those listed will yield better results. To Reduce Input Ripple D5A Models D12A and D24E Models D48A and D48E Models To Reduce Output Ripple 5/5.2V Outputs 12/15V Outputs 47F, 10V 20F, 50V 10F, 100V 47F, 10V, Low ESR 22F, 20V, Low ESR In critical, space-sensitive applications, Murata Power Solutions may be able to tailor the internal input/output filtering of these units to meet your specific requirements. www.murata-ps.com/support MDC_UWR6-10W Series.E01 Page 3 of 6 UWR Series Single Output, High Reliability, 2" x 1", 6-10 Watt, DC-DC Converters Typical Performance Curves (TA = +25C) The performance curves below were derived from actual test data for a single model number (UWR-5/1800-D48A). Since all devices in the 6-10W UWR A-Series have the same circuit topology, the performance curves are representative of all devices. LOAD REGULATION LINE REGULATION Output Voltage vs. Input Voltage and Output Current Output Voltage vs. Output Current and Input Voltage 5.016 5.016 5.014 5.014 VIN = 18V 5.012 IOUT = 0.18A VOUT (Volts) VOUT (Volts) 5.012 5.010 5.008 IOUT = 0.9A 5.010 5.008 5.006 5.006 5.004 5.004 VIN = 72V IOUT = 1.8A VIN = 48V 5.002 5.002 5.000 18 24 30 36 42 48 54 60 66 72 VIN (Volts) 5.000 0.18 0.3 0.6 0.9 1.2 1.5 1.8 Output Current (Amps) EFFICIENCY Efficiency vs. Output Current and Input Voltage 84 81 Efficiency (%) 78 75 VIN = 18V 72 VIN = 48V 69 VIN = 72V 66 63 60 0.18 0.3 0.6 0.9 1.2 1.5 1.8 Output Current (Amps) www.murata-ps.com/support MDC_UWR6-10W Series.E01 Page 4 of 6 UWR Series Single Output, High Reliability, 2" x 1", 6-10 Watt, DC-DC Converters Input Fusing CUSTOM CAPABILITIES Certain applications and/or safety agencies may require the installation of fuses at the inputs of power conversion components. For Murata Power Solutions A-Series UWR 6-10 Watt DC/DC Converters, you should use slowblow type fuses with values no greater than the following: VIN Range D5A D12A and D24E D48A and D48E Fuse Value 3A 2A 1A Our experienced applications and design staffs; quick-turn prototype capability; highly automated, SMT assembly facilities; and in-line SPC quality-control techniques combine to give us the unique ability to design and deliver any quantity of power converters to the highest standards of quality and reliability. EMI RADIATED EMISSIONS If you're designing with EMC in mind, please note that all of Murata Power Solutions' A-Series UWR 6-10 Watt DC/DC Converters have been characterized for radiated and conducted emissions in our new EMI/EMC laboratory. Testing is conducted in an EMCO 5305 GTEM test cell utilizing EMCO automated EMC test software. Radiated emissions are tested to the limits of FCC Part 15, Class B and CISPR 22 (EN 55022), Class B. Radiated emissions plots to FCC and CISPR 22 for model UWR-12/665-D5A appear below. UWR-12/665-D5A Radiated Emissions FCC Part 15 Class B, 3 Meters Converter Output = 12Vdc @ 620mA We have compiled a large library of DC/DC designs that are currently used in a variety of telecom, medical, computer, railway, aerospace and industrial applications. We may already have the converter you need. Contact us. Our goal is to provide you the highest-quality, most costeffective power converters available. Quality and Reliability The A-Series are the first DC/DC Converters to emerge from Murata Power Solutions' new, company-wide approach to designing and manufacturing the most reliable power converters available. The five-pronged program draws our Quality Assurance function into all aspects of new-product design, development, characterization, qualification and manufacturing. Design for Reliability 80 Design for Reliability is woven throughout our multi-phased, new-productdevelopment process. Design-for-reliability practices are fully documented and begin early in the new-product development cycle with the following goals: 1. To work from an approved components/vendors list ensuring the use of reliable components and the rigorous qualification of new components. 2. To design with safety margins by adhering to a strict set of derating guidelines and performing theoretical worst-case analyses. 3. To locate potential design weaknesses early in the product-development cycle by using extensive HALT (Highly Accelerated Life Testing). 4. To prove that early design improvements are effective by employing a thorough FRACA (Failure Reporting Analysis and Corrective Action) System. 70 60 Radiated Emissions (dBV/M) Murata Power Solutions' world-class design, development and manufacturing team stands ready to work with you to deliver the exact power converter you need for your demanding, large volume, OEM applications. And ... we'll do it on time and within budget! FCC Class B Limit 50 40 30 20 10 0 Radiated Emissions -10 -20 1000 100 Frequency (MHz) Soldering Guidelines Murata Power Solutions recommends the specifications below when installing these converters. These specifications vary depending on the solder type. Exceeding these specifications may cause damage to the product. Be cautious when there is high atmospheric humidity. We strongly recommend a mild pre-bake (100 C. for 30 minutes). Your production environment may differ; therefore please thoroughly review these guidelines with your process engineers. UWR-12/665-D5A Radiated Emissions EN 55022 Class B, 10 Meters Converter Output = 12Vdc @ 620mA 80 70 Radiated Emissions (dBV/M) 60 Wave Solder Operations for through-hole mounted products (THMT) 50 EN 55022 Class B Limit 40 For Sn/Ag/Cu based solders: 30 20 10 0 Maximum Preheat Temperature 115 C. Maximum Pot Temperature 270 C. Maximum Solder Dwell Time 7 seconds For Sn/Pb based solders: Radiated Emissions -10 Maximum Preheat Temperature 105 C. -20 Maximum Pot Temperature 250 C. Maximum Solder Dwell Time 6 seconds 1000 100 Frequency (MHz) www.murata-ps.com/support MDC_UWR6-10W Series.E01 Page 5 of 6 UWR Series Single Output, High Reliability, 2" x 1", 6-10 Watt, DC-DC Converters HALT Testing Qualification The goal of the accelerated-stress techniques used by Murata Power Solutions is to force device maturity, in a short period of time, by exposing devices to excessive levels of "every stimulus of potential value." We use HALT (Highly Accelerated Life Testing) repeatedly during the design and early manufacturing phases to detect potential electrical and mechanical design weaknesses that could result in possible future field failures. For each new product, electrical performance is verified via a comprehensive characterization process and long-term reliability is confirmed via a rigorous qualification procedure. The qual procedure includes such strenuous tests as thermal shock and 500 hour life. Qual testing is summarized below. Qualification Testing During HALT, prototype and pre-production DC/DC converters are subjected to progressively higher stress levels induced by thermal cycling, rate of temperature change, vibration, power cycling, product-specific stresses (such as dc voltage variation) and combined environments. The stresses are not meant to simulate field environments but to expose any weaknesses in a product's electro/mechanical design and/or assembly processes. The goal of HALT is to make products fail so that device weaknesses can be analyzed and strengthened as appropriate. Applied stresses are continually stepped up until products eventually fail. After corrective actions and/or design changes, stresses are stepped up again and the cycle is repeated until the "fundamental limit of the technology" is determined. Murata Power Solutions has invested in a Qualmark OVS-1 HALT tester capable of applying voltage and temperature extremes as well as 6-axis, linear and rotational, random vibration. A typical HALT profile (shown above) consists of thermal cycling (-55 to +125C, 30C/minute) and simultaneous, gradually increasing, random longitudinal and rotational vibration up to 20G's with load cycling and applied-voltage extremes added as desired. Many devices in Murata Power Solutions' new A-Series could not be made to fail prior to reaching either the limits of the HALT chamber or some previously known physical limit of the device. We also use the HALT chamber and its ability to rapidly cool devices to verify their "cold-start" capabilities. 100 40 80 20 40 20 0 0 Random Vibration (G's) Temperature (C) 60 Qualification Test Method/Comments HALT Murata Power Solutions in-house procedure High Temperature Storage Max. rated temp., 1,000 hours Thermal Shock 10 cycles, -55 to +125C Temperature/Humidity +85C, 85% humidity, 48 hours Lead Integrity Murata Power Solutions in-house procedure Life Test +70C, 500 hours* Marking Permanency Murata Power Solutions in-house procedure End Point Electrical Tests Per product specification * Interim electrical test at 200 hours. In-Line Process Controls and Screening A combination of statistical sampling and 100% inspection techniques keeps our assembly line under constant control. Parameters such as solder-paste thickness, component placement, cleanliness, etc. are statistically sampled, charted and fine tuned as necessary. Visual inspections are performed by trained operators after pick-and-place, soldering and cleaning operations. Units are 100% electrically tested prior to potting. All devices are temperature cycled, burned-in, hi-pot tested and final-electrical tested prior to external visual examination, packing and shipping. Rapid Response to Problems Murata Power Solutions employs an outstanding corrective-action system to immediately address any detected shortcomings in either products or processes. Whenever our assembly, quality or engineering personnel spot a product/process problem, or if a product is returned with a potential defect, we immediately perform a detailed failure analysis and, if necessary, undertake corrective actions. Over time, this system has helped refine our assembly operation to yield one of the lowest product defect rates in the industry. -20 -40 10 20 30 40 50 60 70 80 90 Test Time (minutes) Typical HALT Profile Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. (c) 2015 Murata Power Solutions, Inc. www.murata-ps.com/support MDC_UWR6-10W Series.E01 Page 6 of 6 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Murata: UWR-12/665-D5A-C UWR-5.2/1500-D5A-C UWR-5/1600-D5A-C UWR-5/1800-D48A-C UWR-5/2000-D12A-C UWR-5/2000-D24E-C