LR645 High Input Voltage SMPS Start-up / Linear Regulator Ordering Information Product marking for TO-243AA: Order Number / Package Max. Input Voltage TO-92 TO-243AA* 450V LR645N3 LR645N8 TO-220 SO-8 LR6 Die where = 2-week alpha date code LR645N5 LR645LG LR645ND *Same as SOT-89. Product supplied on 2000 piece carrier tape reels. General Description Features Accepts inputs from 15V to 450V The Supertex LR6 is a high input voltage, low output current linear regulator. It has a 3-terminal fixed output voltage version available in TO-92, TO-220 and SOT-89 packages as well as an adjustable voltage version available in 8 pin SOIC package. The 3-terminal version functions like any other low voltage 3-terminal regulator except it allows the use of much higher input voltages. When used in a SMPS start-up circuit, it eliminates the need for large power resistors. In this application, current is drawn from the high voltage line only during start-up. Only leakage current flows after start-up thereby reducing the continuous power dissipation to a few milliwatts. Compatible with industry standard PWM ICs. See application note AN-H28. Output currents up to 3mA continuous, 30mA peak Supply current typically 50A Line regulation typically 0.1mV/V Output can be trimmed from 8.0V to 12V Output current can be increased to 150mA with external FET The adjustable voltage version allows trimming of the output voltage from 8V to 12V. This version can also be connected to an external depletion mode MOSFET for increased output current. When used in conjunction with Supertex depletion mode MOSFET DN2540N5, up to a 150mA is achieved. Applications Off-line SMPS startup circuits (pulse loads) Low power off-line regulators Regulators for noisy inputs (continued on page 14-3) Pin Configuration Caution The LR6 does NOT provide galvanic isolation. When operated from an AC line, potentially lethal voltages can be present on the IC. Adequate means of protecting the end user from such voltages must be provided by the circuit developer. TAB TAB 1 2 3 TO-243AA (SOT-89) 123 TO-92 Absolute Maximum Ratings Input Voltage 450V Output Voltage 15.5V Operating and Storage Temperature Soldering Temperature* 5 1 2 3 4 1 SO-8 2 3 TO-220 -55C to +150C +VIN GND VOUT Trim Gate TO-92 1 2 3 -- -- TO-243AA 1 2, TAB 3 -- -- TO-220 1 2, TAB 3 -- -- P-DIP 1 3 4 5 7 300C *Distance of 1.6mm from case for 10 seconds For detailed circuit and application information, please refer to application note AN-H28. 11/12/01 Supertex Inc. does not recommend the use of its products in life support applications and will not knowingly sell its products for use in such applications unless it receives an adequate "products liability indemnification insurance agreement." Supertex does not assume responsibility for use of devices described and limits its liability to the replacement of devices determined to be defective due to workmanship. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the Supertex website: http://www.supertex.com. For complete liability information on all Supertex products, refer to the most current databook or to the Legal/Disclaimer page on the Supertex website. 1 LR645 Block Diagram Thermal Characteristics Power Dissipation @ TA = 25C jc C/W ja C/W SO-8 0.31W 156 400 TO-92 0.74W 125 170 TO-220 1.8W 8.3 70 15 Package TO-243AA 1.6W VIN VOUT 78 Mounted on FR5 board, 25mm x 25mm x 1.57mm. Significant PD increase possible on ceramic substrate. - + Trim Gate GND Electrical Characteristics Test conditions unless otherwise specified: TA = 25C; VIN = 15 to 450V, COUT = 0.01F Symbol VOUT Parameter Output Voltage Temperature 1 Min Typ Max Unit Conditions 9.3 10 10.7 V No load 9.0 10 11.5 V TJ = -40C to + 125C, No load VOUT Output Voltage over VOUT Line Regulation 40 200 mV VIN=15V to 400V, No load VOUT Load Regulation 150 400 mV VIN=50V, IOUT=0 to 3.0mA VIN Operating Input Voltage Range 450 V IINQ Input Quiescent Current 50 150 A No Load IOFF VIN Off-State Leakage Current 0.1 10 A VAUXVOUT+1V applied to VOUT pin IAUX Input Current to VOUT 200 A VAUXVOUT+1V applied to VOUT pin 60 dB 120Hz, No Load 25 V 0.01 to 100KHz 30 mA COUT = 10F, VIN = 400V VOUT/VIN en Ripple Rejection Ratio Noise voltage 1 15 50 1 Current 2 IPEAK Output Peak VAUX External Voltage Applied to VOUT 13.2 V 8-pin, adjustable output voltage version only. Test conditions unless otherwise specified: TA = 25C; VIN = 15 to 450V, COUT = 0.01F Symbol VOUT VOUT VOUT Parameter Output Voltage Trim Range1 Load Regulation at 8V Min Typ Unit 12 V 200 400 mV VIN=15V, IOUT=0 to 1.0mA 100 400 mV VIN=50V, IOUT=0 to 3.0mA 8 trim1 Load Regulation at 12V Max trim1 Notes: 1. Guaranteed by design, not tested in production. 2. Pulse test duration < 1msec, Duty cycle < 2% 2 Conditions No load LR645 LR6: High Current SMPS Start-Up Circuit General Description (Continued from page 14-1) LR6: SMPS Start-Up Circuit The 8 pin version of the LR6 has connections for an external depletion-mode MOSFET for higher output current and external resistors for adjustable output voltage. As shown in Figure 2, the output current is increased to 150mA by using the Supertex 400V depletion-mode MOSFET DN2540. The maximum operating input voltage will be limited by the drain-to-source breakdown voltage of the external MOSFET, but cannot exceed the 450V rating of LR6. One of the main applications for the LR6 is a start-up circuit for off-line switch-mode power supplies (SMPS) as shown in Figure 1. A minimum output capacitance of 0.01F is recommended for stability. The wide operating input voltage range of the LR6 allows the SMPS to operate and start-up from rectified AC or a DC voltage 15V to 450V without adjustment. During start-up, the LR6 powers the VCC line of the PWM IC with a nominal output voltage of 10V. The auxiliary voltage connected through a diode to the VOUT pin of the LR6 will start to increase. When the auxiliary voltage becomes larger than the output voltage the LR6 turns OFF its internal high voltage input line and output voltage allowing the auxiliary voltage to power the VCC line of the PWM IC. The input current drawn by the LR6 from the high voltage line after start-up will therefore only be leakage current of the internal MOSFET switch, which is typically 0.1A. The output voltage can be adjusted from 8V to 12V with 2 external resistors, R1 and R2. The ratio of R2/R1 determines the output voltage. R2 is connected between the VOUT and Trim pins. R1 is connected between Trim and GND pins. Figure 5 is a curve showing output voltage versus resistor ratio R2/R1. The optimum range for R1 + R2 is 200K to 300K. This minimizes loading and optimizes accuracy of the output voltage. Figure 5 uses an R1 + R2 of 250K. The 3-terminal version shown in Figure 1 has load regulation guaranteed from 0 to 3.0mA at a fixed nominal output voltage of 10V. Applications requiring higher output current and/or a different output voltage can use the 8 pin adjustable version. Figure 1: SMPS Start-Up Circuit + + 5.0V - VAUX=12V 15V to 450V VIN VOUT VCC LR6 PWM IC COUT C IN GND - Figure 2: High Current SMPS Start-Up + + 5.0V DN2540 - VAUX=12V Gate 15V to 400V VOUT LR645LG C IN VCC R2 Trim GND PWM IC COUT R1 - Note: When used with the DN25, +VIN is not connected on the LR6. 3 LR645 LR6:Off Line Linear Regulator PDISS Circuits requiring low voltages to operate logic and analog circuits benefit from the LR6. The conventional use of step down transformers can be eliminated thereby saving space and cost. Some examples of these applications are proximity controlled light switches, street lamp control, and low voltage power supplies for appliances such as washing machines, dishwashers, and refrigerators. = (VIN - VOUT) x (IOUT + IMAX QUIESCENT) = (400V - 10V) x (3.0mA + 150A) = 1.23 Watts The 1.23 watts is for continuous operation. This is within the dissipation capabilities of the TO-220 and SOT-89 packages. See Page 14-2, thermal characteristics, for deratings. For SMPS start-up applications, the output current is usually required only during start-up. This duration depends upon the auxiliary supply output capacitor and COUT but is typically a few hundred milliseconds. The wide operating input voltage range of 15V to 450V as well as the ripple rejection ratio of 50dB minimum allow the use of small high voltage input capacitor. The input AC line can be either fullwave or half-wave rectified. A minimum output capacitance of 0.01F is recommended for output stability. All package types of the LR6 have been characterized for use with a COUT of at least 10F , and an AC line of 277V. Figure 3 shows the LR6 as a pre-regulator to a precision regulator for high precision regulation. Higher output current is also possible by using an external depletion-mode MOSFET DN2540N5 as shown in Figure 4. Figure 5: Typical Output Voltage vs. Resistor Ratio Figure 3: Cascading for Precision 12 Max 875 ACSA AC Line (24 to 277VAC) CIN 1F COUT .01F 5.000V .002V @ 0 to 3mA Output Voltage LR6 Power Dissipation Considerations The LR6 is a true linear regulator. Its power dissipation is therefore a function of input voltage and output load current. For example, if the LR6 is providing a continuous load current of 3mA at 10V while its input voltage is 400V, total dissipation in the LR6 will be: 10 R1 + R2 = 250K 8 2.5 3.0 3.5 4.0 Resistor Ratio, R2/R1 Figure 4: High Current Regulator DN2540N5 AC Line (24 to 277VAC) Gate LR645LG CIN VOUT COUT 5.0V Reg 5.0V + 0 to 150mA - GND 11/12/01 (c)2001 Supertex Inc. All rights reserved. Unauthorized use or reproduction prohibited. 4 1235 Bordeaux Drive, Sunnyvale, CA 94089 TEL: (408) 744-0100 * FAX: (408) 222-4895 www.supertex.com