Technical S pecification PQ60012EGL20 48V in 1.2Vout 20Amp 2000Vdc Eighth-brick Input Output Current Isolation DC/DC Conver ter Th e PQ6 0012 E GL 20 Pow e r Qor TM G ig a e i gh th- bri ck con v er t er is a n ext -ge ner a ti on , b o ar d- mo un t ab l e, iso la t ed , fixed s witch ing freq u enc y DC/DC c on ver ter tha t u ses s y nch r o n ou s r ectification to ach ieve extr emel y h igh con vers io n e ffi c ienc y. Th e p owe r d is sip a ted by th e co nver ter is s o lo w tha t a he at s ink is no t r eq ui red , wh ich sa v es c os t, we ight , h eigh t , a n d a p pl ica tion effor t. Al l of th e p ower an d con tro l co m p on en ts a r e mo un ted to th e mu l ti-l ay er P CB s ub s tra te with h igh -y iel d su r fac e mo un t tec hn ol ogy . Si nce the P ower Q or c on ve rt er h a s no exp l icit th er ma l int er fa ces , it is ex tr emel y reliable. RoHS 5/6 Compliant (see page 12 ). Operational Features PQ60012EGL20 Module * High efficiency, >82% at full rated load current * Delivers up to 20 amps of output current with minimal derating - no heatsink required * Wide input voltage range: 35V - 75V, with 100V 100ms input voltage transient capability * Fixed frequency switching provides predictable EMI performance * No minimum load requirement means no preload resistors required Mechanical Features * Industry standard eighth-brick pin-out configuration * Industry standard size: 0.90" x 2.3" (22.9x58.4mm) * Total height only 0.335" (8.5mm), permits better airflow and smaller card pitch * Total weight: 0.68 oz. (19 grams) * Flanged pins designed to permit surface mount soldering (avoid wave solder) using FPiP technique Contr ol Features * On/Off control referenced to input side (positive and negative logic options are available) * Remote sense for the output voltage compensates for output distribution drops * Output voltage trim permits custom voltages and voltage margining Product # PQ60012EGL20 Phone 1-888-567-9596 www.synqor.com Pr otection Features * Input under-voltage lockout disables converter at low input voltage conditions * Output current limit and short circuit protection protects converter and load from permanent damage and consequent hazardous conditions * Active back bias limit prevents damage to converter from external load induced pre-bias * Output over-voltage protection protects load from damaging voltages * Thermal shutdown protects converter from abnormal environmental conditions Safety Features * 2000V, 30 M input-to-output isolation provides input/output ground separation * UL 1950 recognized (US & Canada), basic insulation rating * TUV certified to EN60950-1 * Meets 72/23/EEC and 93/68/EEC directives which facilitates CE Marking in user's end product * Board and plastic components meet UL94V-0 flammability requirements Doc.# 005-2EG621G Rev. B 02/10/06 Page 1 Input: Output: Current: Package: Technical Specification MECHANICAL DIAGRAM 0.14 2.30 (3.56) (58.42) 35-75 V 1.2 V 20 A Eighth-brick 0.90 (22.86) 0.450 (11.43) Top View 0.150 0.300 2.00 0.150 (50.8) (3.81) 1 8 7 2 6 5 3 4 (3.81) (7.62) 0.600 (15.24) 0.335 (8.5) Side View Bottom side Clearance EGA Option 0.424 (10.76) max height See Note 9 See Note 9 0.019 +0.013 (0.48 +0.33) Lowest Component Flanged Pin See Note 10 Load Board EGA Option 0.076 (1.93) min clearance 0.110 (2.79) See Note 3 See Note 9 NOTES PIN DESIGNATIONS 1) Pins 1-3, 5-7 are 0.040" (1.02mm) diameter. with 0.080" (2.03mm) diameter standoff shoulders. 2) Pins 4 and 8 are 0.062" (1.57 mm) diameter with 0.100" (2.54 mm) diameter standoff shoulders. 3) Other pin extension lengths available. Recommended pin length is 0.03" (0.76mm) greater than the PCB thickness. 4) All Pins: Material - Copper Alloy Finish - Tin/Lead over Nickel plate 5) Undimensioned components are shown for visual reference only. 6) All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm) x.xxx +/-0.010 in. (x.xx +/-0.25mm) 7) Weight: 0.68 oz. (19 g) typical 8) Workmanship: Meets or exceeds IPC-A-610C Class II 9) Modules can be ordered as EGA option that have different pins to provide a minimum bottom side clearance of 0.076" while increasing maximum height to 0.424". See ordering page for more information. 10) The flanged pins are designed to permit surface mount soldering (allowing to avoid the wave soldering process) through the use of the flanged pin-in-paste technique. Product # PQ60012EGL20 Phone 1-888-567-9596 Pin No. Name Function 1 Vin(+) Positive input voltage 2 ON/OFF TTL input to turn converter on and off, referenced to Vin(-), with internal pull up. 3 Vin(-) Negative input voltage 4 Vout(-) Negative output voltage 5 SENSE(-) Negative remote sense1 6 TRIM Output voltage trim2 7 SENSE(+) Positive remote sense3 8 Vout(+) Positive output voltage Notes: 1. SENSE(-) should be connected to Vout(-) either remotely or at the converter. 2. Leave TRIM pin open for nominal output voltage. 3. SENSE(+) should be connected to Vout(+) either remotely or at the converter. www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 2 Input: Output: Current: Package: Technical Specification 35-75 V 1.2 V 20 A Eighth-brick PQ60012EGL20 ELECTRICAL CHARACTERISTICS TA=25C, airflow rate=300 LFM, Vin=48Vdc unless otherwise noted; full operating temperature range is -40C to +100C ambient temperature with appropriate power derating. Specifications subject to change without notice. Parameter Min. Typ. Max. Units 100 80 100 2000 100 125 18 V V V V C C V Notes & Conditions ABSOLUTE MAXIMUM RATINGS Input Voltage Non-Operating Operating Operating Transient Protection Isolation Voltage (input to output) Operating Temperature Storage Temperature Voltage at ON/OFF input pin INPUT CHARACTERISTICS Operating Input Voltage Range Input Under-Voltage Lockout Turn-On Voltage Threshold Turn-Off Voltage Threshold Lockout Voltage Hysteresis Maximum Input Current No-Load Input Current Disabled Input Current Inrush Current Transient Rating Response to Input Transient Input Reflected Ripple Current Input Terminal Ripple Current Recommended Input Fuse Input Filter Component Values (L\C) Recommended External Input Capacitance OUTPUT CHARACTERISTICS Output Voltage Set Point Output Voltage Regulation Over Line Over Load Over Temperature Total Output Voltage Range Output Voltage Ripple and Noise1 Peak-to-Peak RMS Operating Output Current Range Output DC Current-Limit Inception Output DC Current-Limit Shutdown Voltage Back-Drive Current Limit while Enabled Back-Drive Current Limit while Disabled Maximum Output Capacitance -40 -55 -2 35 48 75 V 31.5 29.5 2.2 33.3 31.0 2.3 34.4 32.4 2.4 0.9 V V V A mA mA A 2s mV mA mA A H\F F 25 2 50 3.0 110 4.7\1.0 47 1.188 1.155 0 DYNAMIC CHARACTERISTICS Input Voltage Ripple Rejection Output Voltage during Load Current Transient For a Step Change in Output Current (0.1A/s) For a Step Change in Output Current (5A/s) Settling Time Turn-On Transient Turn-On Time Start-Up Inhibit Time Output Voltage Overshoot EFFICIENCY 100% Load 50% Load 180 5 0.01 10 1.20 1.212 V +0.05 \ 2 +0.1 \ 2 +6 +0.1 \ 5 +0.2 \ 5 +20 1.245 %\mV %\mV mV V 70 18 130 30 20 mV mV A A V A mA F 23 0.9 0.45 10 50 45,000 1000V/ms input transient RMS thru 10H inductor; Figures 13 & 15 RMS; Figures 13 & 14 Fast blow external fuse recommended Internal values, see Figure F Typical ESR 0.1-0.2, see Figure 13 Over sample, line, load, temperature & life 20MHz bandwidth; Figures 13 & 16 Full Load, see Figures 13 & 16 Full Load, see Figures 13 & 16 Subject to thermal derating; Figures 5 - 8 Output Voltage 10% Low; Figure 17 Negative current drawn from output Negative current drawn from output 1.2Vout at 20A Resistive Load dB 120 Hz; Figure 20 50 80 600 mV mV s 50% to 75% to 50% Iout max; Figure 11 50% to 75% to 50% Iout max; Figure 12 To within 1% Vout nom ms ms % Full load, Vout=90% nom.; Figures 9 & 10 -40C to +125C; Figure G 45,000 F load capacitance, Iout = 0A % % Figures 1 - 4 Figures 1 - 4 C C C Package rated to 150C UL rated max operating temp 130C See Figures 5 - 8 for derating curves 14 200 0 TEMPERATURE LIMITS FOR POWER DERATING CURVES Semiconductor Junction Temperature Board Temperature Transformer Temperature Isolation Voltage (dielectric strength) Isolation Resistance Isolation Capacitance2 100% Load, 35 Vin 80 18 240 82.5 84.5 ISOLATION CHARACTERISTICS Continuous Continuous 100ms transient, square wave Basic insulation, Pollution Degree 2 125 125 125 2000 30 470 V M pF Note 1: For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Note 2: Higher values of isolation capacitance can be added external to the module. Product # PQ60012EGL20 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 3 Input: Output: Current: Package: Technical Specification 35-75 V 1.2 V 20 A Eighth-brick ELECTRICAL CHARACTERISTICS (Continued) Parameter P FEATURE CHARACTERISTICS Switching Frequency ON/OFF Control (Option P) Off-State Voltage On-State Voltage ON/OFF Control (Option N) Off-State Voltage On-State Voltage ON/OFF Control (Either Option) Pull-Up Voltage Pull-Up Resistance Output Voltage Trim Range Output Voltage Remote Sense Range Output Over-Voltage Protection Over-Temperature Shutdown Over-Temperature Shutdown Restart Hysteresis Load Current Scale Factor Min. Typ. Max. Units 195 225 255 kHz -2 2.4 0.8 18 V V 2.4 -2 18 0.8 V V 15 V k % % % C C -20 Vin/6 40 120 RELIABILITY CHARACTERISTICS Calculated MTBF (Telcordia) Calculated MTBF (MIL-217) Field Demonstrated MTBF 125 125 10 500 +10 +10 130 Notes & Conditions Regulation and Isolation stages Figures A & B Measured across Pins 8 & 4; Figure C Measured across Pins 8 & 4 Over full temp range; % of nominal Vout Average PCB Temperature See App Note: Output Load Current Calc. 10 Hrs. TR-NWT-000332; 80% load,300LFM, 40oC Ta 106 Hrs. MIL-HDBK-217F; 80% load, 300LFM, 40oC Ta 106 Hrs. See website for details 6 2.5 1.1 STANDARDS COMPLIANCE Parameter P Notes STANDARDS COMPLIANCE UL/cUL 60950-1 EN60950-1 72/23/EEC 93/68/EEC Needle Flame Test (IEC 695-2-2) IEC 61000-4-2 GR-1089-CORE Telcordia (Bellcore) GR-513 File # E194341, Basic insulation & pollution degree 2 Certified by TUV test on entire assembly; board & plastic components UL94V-0 compliant ESD test, 8kV - NP, 15kV air - NP (Normal Performance) Section 7 - electrical safety, Section 9 - bonding/grounding * An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new releases or download from the SynQor website. QUALIFICATION TESTING Parameter P QUALIFICATION TESTING Life Test Vibration Mechanical Shock Temperature Cycling Power/Thermal Cycling Design Marginality Humidity Solderability # Units 32 5 5 10 5 5 5 15 pins Test Conditions 95% rated Vin and load, units at derating point, 1000 hours 10-55Hz sweep, 0.060" total excursion,1 min./sweep, 120 sweeps for 3 axis 100g minimum, 2 drops in x and y axis, 1 drop in z axis -40C to 100C, unit temp. ramp 15C/min., 500 cycles Toperating = min to max, Vin = min to max, full load, 100 cycles Tmin-10C to Tmax+10C, 5C steps, Vin = min to max, 0-105% load 85C, 85% RH, 1000 hours, 2 minutes on and 6 hours off MIL-STD-883, method 2003 * Extensive characterization testing of all SynQor products and manufacturing processes is performed to ensure that we supply robust, reliable product. Contact the factory for official product family qualification documents. OPTIONS PATENTS SynQor provides various options for Enable Logic and Pin Length for this family of DC/DC converters. Please consult the last page of this specification sheet for information on available options. SynQor is protected under various patents, including but not limited to U.S. Patent numbers 5,999,417; 6,222,742 B1; 6,594,159 B2; 6,545,890 B2. Product # PQ60012EGL20 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 4 Input: Output: Current: Package: Technical Specification 35-75 V 1.2 V 20 A Eighth-brick 88 95 87 90 86 Efficiency (%) Efficiency (%) 85 80 75 70 85 84 83 25 C 40 C 55 C 82 35 Vin 65 81 48 Vin 75 Vin 80 60 0 2 4 6 8 10 12 14 16 18 0 20 100 200 300 400 500 Air Flow (LFM) Load Current (A) Figure 1: Efficiency at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. Figure 2: Efficiency at nominal output voltage and 60% rated power vs. airflow rate for ambient air temperatures of 25C, 40C, and 55C (nominal input voltage). 8 5 Power Dissipation (W) Power Dissipation (W) 7 6 5 4 3 2 35 Vin 1 48 Vin 0 2 4 6 8 10 12 14 16 18 3 2 25 C 40 C 1 55 C 75 Vin 0 4 0 0 20 100 200 300 400 500 Air Flow (LFM) Load Current (A) Figure 3: Power dissipation at nominal output voltage vs. load current for minimum, nominal, and maximum input voltage at 25C. Figure 4: Power dissipation at nominal output voltage and 60% rated power vs. airflow rate for ambient air temperatures of 25C, 40C, and 55C (nominal input voltage). 22 20 18 16 Iout (A) 14 12 10 8 400 LFM (2.0 m/s) 6 300 LFM (1.5 m/s) 4 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 2 50 LFM (0.25 m/s) 0 0 25 40 55 70 Semiconductor junction temperature is within 1C of surface temperature 85 Ambient Air Temperature (oC) Figure 5: Maximum output power derating curves vs. ambient air temperature for airflow rates of 50 LFM through 400 LFM with air flowing across the converter from pin 3 to pin 1 (nominal input voltage). Product # PQ60012EGL20 Phone 1-888-567-9596 Figure 6: Thermal plot of converter at 20 amp load current with 55C air flowing at the rate of 200 LFM. Air is flowing across the converter sideways from pin 3 to pin 1 (nominal input voltage). www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 5 Input: Output: Current: Package: Technical Specification 35-75 V 1.2 V 20 A Eighth-brick 22 20 18 16 Iout (A) 14 12 10 8 400 LFM (2.0 m/s) 6 300 LFM (1.5 m/s) 4 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) 2 50 LFM (0.25 m/s) 0 0 25 40 55 70 Semiconductor junction temperature is within 1C of surface temperature 85 Ambient Air Temperature (oC) Figure 7: Maximum output power-derating curves vs. ambient air temperature for airflow rates of 50 LFM through 400 LFM with air flowing from input to output (nominal input voltage). Figure 8: Thermal plot of converter at 20 amp load current with 55C air flowing at the rate of 200 LFM. Air is flowing across the converter from input to output (nominal input voltage). Figure 9: Turn-on transient at full load (resistive load) (4 ms/div). Input voltage pre-applied. Ch 1: Vout (500mV/div). Ch 2: ON/OFF input (5V/div). Figure 10: Turn-on transient at zero load (4 ms/div). Ch 1: Vout (500mV/div). Ch 2: ON/OFF input (5V/div). Figure 11: Output voltage response to step-change in load current (50%- Figure 12: Output voltage response to step-change in load current (50%75%-50% of Iout(max): dI/dt = 5A/s). Load cap: 470F, 30 m ESR tantalum cap and 1F ceramic cap. Ch 1: Vout (100mV/div). Ch 2: Iout (5A/div). 75%-50% of Iout(max); dI/dt = 0.1A/s). Load cap: 10F, 100 m ESR tantalum cap and 1F ceramic cap. Ch 1: Vout (100mV/div). Ch 2: Iout (5A/div). Product # PQ60012EGL20 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 6 Input: Output: Current: Package: Technical Specification 35-75 V 1.2 V 20 A Eighth-brick See Fig. 15 10 H See Fig. 14 source impedance See Fig. 16 iS VSOURCE iC DC/DC Converter VOUT 10 F, 1 F 47 F, <1 ESR ceramic 100m ESR capacitor tantalum capacitor electrolytic capacitor Figure 13: Test set-up diagram showing measurement points for Input Terminal Ripple Current (Figure 14), Input Reflected Ripple Current (Figure 15) and Output Voltage Ripple (Figure 16). Figure 14: Input Terminal Ripple Current, ic, at full rated output current and nominal input voltage with 10 H source impedance and 47 F electrolytic capacitor (100 mA/div). See Figure 13. Figure 15: Input Reflected Ripple Current, is, through a 10 H source inductor at nominal input voltage and rated load current (5 mA/div). See Figure 13. Figure 16: Output Voltage Ripple at nominal input voltage and rated load current (50 mV/div). Load capacitance: 1 F ceramic capacitor and 10 F tantalum capacitor. Bandwidth: 20 MHz. See Figure 13. Output Voltage (V) 2.0 1.5 1.0 35 V 0.5 48 V 75 V 0.0 0 5 10 15 20 25 30 Load Current (A) Figure 17: Output voltage vs. load current showing typical current limit curves and converter shutdown points. Product # PQ60012EGL20 Phone 1-888-567-9596 Figure 18: Load current (20A/div) as a function of time when the converter attempts to turn on into a 10 m short circuit. Top trace (2.5ms/div) is an expansion of the on-time portion of the bottom trace. www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 7 Input: Output: Current: Package: Technical Specification 0.1 35-75 V 1.2 V 20 A Eighth-brick -30 0.01 35 Vin 48 Vin 75 Vin 0.001 Forward Transmission (dB) Output Impedance ( ) -40 -50 -60 35 Vin -70 48 Vin 75 Vin -80 -90 -100 0.0001 -110 10 100 1,000 10,000 100,000 10 100 Hz 10,000 100,000 Hz Figure 19: Magnitude of incremental output impedance (Zout = vout/iout) for minimum, nominal, and maximum input voltage at full rated power. Figure 20: Magnitude of incremental forward transmission (FT = vout/vin) for minimum, nominal, and maximum input voltage at full rated power. 0 1000 -10 -20 35 Vin -30 48 Vin 75 Vin -40 Input Impedance ( ) Reverse Transmission (dB) 1,000 100 35 Vin 10 48 Vin 75 Vin 1 -50 -60 0.1 10 100 1,000 10,000 100,000 10 Hz Figure 21: Magnitude of incremental reverse transmission (RT = iin/iout) for minimum, nominal, and maximum input voltage at full rated power. Product # PQ60012EGL20 Phone 1-888-567-9596 100 1,000 Hz 10,000 100,000 Figure 22: Magnitude of incremental input impedance (Zin = vin/iin) for minimum, nominal, and maximum input voltage at full rated power. www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 8 Input: Output: Current: Package: Technical Specification 35-75 V 1.2 V 20 A Eighth-brick BASIC OPERATION AND FEATURES CONTROL FEATURES The PowerQor series converter uses a two-stage power conversion topology. The first stage is a buck-converter that keeps the output voltage constant over variations in line, load, and temperature. The second stage uses a transformer to provide the functions of input/output isolation and voltage step-down to achieve the low output voltage required. REMOTE ON/OFF (Pin 2): The ON/OFF input, Pin 2, permits the user to control when the converter is on or off. This input is referenced to the return terminal of the input bus, Vin(-). There are two versions of the converter that differ by the sense of the logic used for the ON/OFF input. Both the first stage and the second stage switch at a fixed frequency for predictable EMI performance. Rectification of the transformer's output is accomplished with synchronous rectifiers. These devices, which are MOSFETs with a very low on-state resistance, dissipate far less energy than Schottky diodes. This is the primary reason that the PowerQor converter has such high efficiency, even at very low output voltages and very high output currents. Dissipation throughout the converter is so low that it does not require a heatsink for operation. Since a heatsink is not required, the PowerQor converter does not need a metal baseplate or potting material to help conduct the dissipated energy to the heatsink. The PowerQor converter can thus be built more simply and reliably using high yield surface mount techniques on a PCB substrate. The PowerQor series of eighth-brick, quarter-brick and half-brick converters uses the industry standard footprint and pin-out configuration. In the positive logic version, the ON/OFF input is active high (meaning that a high turns the converter on). In the negative logic version, the ON/OFF signal is active low (meaning that a low turns the converter on). Figure A details five possible circuits for driving the ON/OFF pin. Figure B is a detailed look of the internal ON/OFF circuitry. REMOTE SENSE() (Pins 7 and 5): The SENSE() inputs correct for voltage drops along the conductors that connect the converter's output pins to the load. Pin 7 should be connected to Vout(+) and Pin 5 should be connected to Vout(-) at the point on the board where regulation is desired. A remote connection at the load can adjust for a voltage drop only as large as that specified in this datasheet, that is [Vout(+) - Vout(-)] - [Vsense(+) - Vsense(-)] < Sense Range % x Vout Pins 7 and 5 must be connected for proper regulation of the output voltage. If these connections are not made, the converter will deliver an output voltage that is slightly higher than its specified value. Note: the output over-voltage protection circuit senses the voltage across the output (pins 8 and 4) to determine when it should trig- ON/OFF ON/OFF ON/OFF Vin(_) Vin(_) Vin(_) Remote Enable Circuit Negative Logic (Permanently Enabled) ON/OFF Positive Logic (Permanently Enabled) 5V Vin(+) 5V 274k ON/OFF 50k TTL TTL/ CMOS ON/OFF Vin(_) Vin(_) Open Collector Enable Circuit Vin(_) Direct Logic Drive Figure A: Various circuits for driving the ON/OFF pin Product # PQ60012EGL20 100pF 50k Phone 1-888-567-9596 Figure B: Internal ON/OFF pin circuitry www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 9 Input: Output: Current: Package: Technical Specification ger, not the voltage across the converter's sense leads (pins 7 and 5). Therefore, the resistive drop on the board should be small enough so that output OVP does not trigger, even during load transients. OUTPUT VOLTAGE TRIM (Pin 6): The TRIM input permits the user to adjust the output voltage across the sense leads up or down according to the trim range specifications. To decrease the output voltage, the user should connect a resistor between Pin 6 and Pin 5 (SENSE(-) input). To increase the output voltage, the user should connect a resistor between Pin 6 and Pin 7 (SENSE(+) input). For a desired change of the nominal output voltage, the value of the resistor should be 35-75 V 1.2 V 20 A Eighth-brick Alternative Trim Equation: When ordering this option (see ordering information page) Tyco compatible trim equations are applicable (range from -10% to +10%, see Figure D) TRIM UP: Rtrim-up = 5.1 x VNOM x (100 + %) [ 0.6 x % TRIM DOWN: Rtrim-down = [ 510 % 510 % ] 10.2 (k) ] 10.2 (k) Where Rtrim = VDES -1 VNOM - VDES % = (k) VDES - VNOM x 100 VNOM 1000 where Trim Resistance (kOhms) VNOM = Nominal Voltage VDES = Desired Voltage (Vertical bars indicate absolute value) Figure C graphs the relationship between the trim resistor value and Rtrim-up and Rtrim-down, showing the total range the output voltage can be trimmed up or down (range from -20% to +10%). 100 10 100 1.08 1.12 1.16 1.20 1.24 1.28 1.32 Trim Resistance (kOhms) Desired Output Voltage Figure D: Alternative Trim Graph for 1.2Vout module Total DC Variation of Vout: For the converter to meet its full specifications, the maximum variation of the DC value of Vout, due to both trimming and remote load voltage drops, should not be greater than that specified for the output voltage trim range. 10 PROTECTION FEATURES 1 0.96 1.00 1.04 1.08 1.12 1.16 1.20 1.24 1.28 1.32 Desired Output Voltage Figure C: Trim Graph for 1.2Vout module Note: The TRIM feature does not affect the voltage at which the output over-voltage protection circuit is triggered. Trimming the output voltage too high may cause the over-voltage protection circuit to engage, particularly during transients. It is not necessary for the user to add capacitance at the Trim pin. The node is internally bypassed to eliminate noise. Product # PQ60012EGL20 Phone 1-888-567-9596 Input Under-Voltage Lockout: The converter is designed to turn off when the input voltage is too low, helping avoid an input system instability problem, described in more detail in the application note titled "Input System Instability". The lockout circuitry is a comparator with DC hysteresis. When the input voltage is rising, it must exceed the typical Turn-On Voltage Threshold value (listed on the specification page) before the converter will turn on. Once the converter is on, the input voltage must fall below the typical Turn-Off Voltage Threshold value before the converter will turn off. www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 10 Input: Output: Current: Package: Technical Specification Output Current Limit: The maximum current limit remains constant as the output voltage drops. However, once the impedance of the short across the output is small enough to make the output voltage drop below the specified Output DC Current-Limit Shutdown Voltage, the converter turns off. The converter then enters a "hiccup mode" where it repeatedly turns on and off at a 5 Hz (nominal) frequency with a 5% duty cycle until the short circuit condition is removed. This prevents excessive heating of the converter or the load board. Output Over-Voltage Limit: If the voltage across the output pins exceeds the Output Over-Voltage Protection threshold, the converter will immediately stop switching. This prevents damage to the load circuit due to 1) excessive series resistance in output current path from converter output pins to sense point, 2) a release of a short-circuit condition, or 3) a release of a current limit condition. Load capacitance determines exactly how high the output voltage will rise in response to these conditions. After 200 ms the converter will automatically restart. Over-Temperature Shutdown: A temperature sensor on the converter senses the average temperature of the module. The thermal shutdown circuit is designed to turn the converter off when the temperature at the sensed location reaches the OverTemperature Shutdown value. It will allow the converter to turn on again when the temperature of the sensed location falls by the amount of the Over-Temperature Shutdown Restart Hysteresis value. APPLICATION CONSIDERATIONS Input System Instability: This condition can occur because any DC/DC converter appears incrementally as a negative resistance load. A detailed application note titled "Input System Instability" is available on the SynQor website which provides an understanding of why this instability arises, and shows the preferred solution for correcting it. Application Circuits: Figure E below provides a typical circuit diagram which details the input filtering and voltage trimming. Input Filtering and External Capacitance: Figure F below provides a diagram showing the internal input filter components. This filter dramatically reduces input terminal ripple current, which otherwise could exceed the rating of an external electrolytic input capacitor. The recommended external input capacitance is specified in the "Input Characteristics" section. More detailed information is available in the application note titled "EMI Characteristics" on the SynQor website. Vin(+) Vin External Input Filter Vout(+) Vsense(+) Electrolytic Capacitor 47F 35-75 V 1.2 V 20 A Eighth-brick ON/OFF Trim Vsense(_) Vin(_) Rtrim-up or Rtrim-down Cload Iload Vout(_) Figure E: Typical application circuit (negative logic unit, permanently enabled). L Vin(+) C Vin(_) Figure F: Internal Input Filter Diagram (component values listed on page 3). Product # PQ60012EGL20 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 11 Input: Output: Current: Package: Technical Specification 35-75 V 1.2 V 20 A Eighth-brick Startup Inhibit Period: The Startup Inhibit Period ensures that the converter will remain off for approximately 200ms when it is shut down for any reason. When an output short is present, this generates a 5Hz "hiccup mode," which prevents the converter from overheating. In all, there are seven ways that the converter can be shut down, initiating a Startup Inhibit Period: At time t1, the unit is disabled by the ON/OFF pin, and it cannot be enabled again until the Startup Inhibit Period has elapsed. * Input Under-Voltage Lockout RoHS Compliance: The EU led RoHS (Restriction of Hazardous Substances) Directive bans the use of Lead, Cadmium, Hexavalent Chromium, Mercury, Polybrominated Biphenyls (PBB), and Polybrominated Diphenyl Ether (PBDE) in Electrical and Electronic Equipment. SynQor products are currently 5/6 RoHS compliant with lead being the exception. For more information please visit our RoHS Compliance / Lead Free Initiative web page or e-mail us at rohs@synqor.com. * Input Over-Voltage Shutdown (not present in Eighth-brick) * Output Over-Voltage Protection * Over Temperature Shutdown * Current Limit * Short Circuit Protection * Turned off by the ON/OFF input When the ON/OFF pin goes high after t2, the Startup Inhibit Period has elapsed, and the output turns on within the typical Turn-On Time. Figure G shows three turn-on scenarios, where a Startup Inhibit Period is initiated at t0, t1, and t2: Before time t0, when the input voltage is below the UVL threshold, the unit is disabled by the Input Under-Voltage Lockout feature. When the input voltage rises above the UVL threshold, the Input Under-Voltage Lockout is released, and a Startup Inhibit Period is initiated. At the end of this delay, the ON/OFF pin is evaluated, and since it is active, the unit turns on. Vin Under-Voltage Lockout Turn-On Threshold ON/OFF (pos logic) ON OFF OFF ON ON 14ms (typical turn on time) Vout 200ms (typical start-up inhibit period) t1 t0 200ms 200ms t2 t Figure G: Startup Inhibit Period (turn-on time not to scale) Product # PQ60012EGL20 Phone 1-888-567-9596 www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 12 Input: Output: Current: Package: Technical Specification 35-75 V 1.2 V 20 A Eighth-brick PART NUMBERING SYSTEM ORDERING INFORMATION The part numbering system for SynQor's PowerQor DC/DC converters follows the format shown in the example below. The tables below show the valid model numbers and ordering options for converters in this product family. When ordering SynQor converters, please ensure that you use the complete 15 character part number consisting of the 12 character base part number and the additional 3 characters for options. PQ 60 012 E G L 20 N N S Options (see Ordering Information) Output Current Thermal Design Performance Level Package Size Output Voltage Input Voltage Product Family The first 12 characters comprise the base part number and the last 3 characters indicate available options. Although there are no default values for enable logic and pin length, the most common options are negative logic and 0.145" pins. These part numbers are more likely to be readily available in stock for evaluation and prototype quantities. Model Number Input Voltage PQ60010EGw 20xyz PQ60010EGw 25xyz PQ60012EGw 20xyz PQ60012EGw 25xyz PQ60015EGw 20xy S PQ60015EGw 25xy S PQ60018EGw 20xy S PQ60018EGw 25xy S PQ60025EGw 20xy S PQ60025EGw 25xy S PQ60033EGw 20xy S PQ60050EGw15xy S PQ60120EGw 07xy S 35 - 75 V 35 - 75 V 35 - 75 V 35 - 75 V 35 - 75 V 35 - 75 V 35 - 75 V 35 - 75 V 35 - 75 V 35 - 75 V 35 - 75 V 35 - 75 V 35 - 75 V Output Max Output Voltage Current 1.0 V 20 A 1.0 V 25 A 1.2 V 20 A 1.2 V 25 A 1.5 V 20 A 1.5 V 25 A 1.8 V 20 A 1.8 V 25 A 2.5 V 20 A 2.5 V 25 A 3.3 V 20 A 5.0 V 15 A 12 V 6.25 A Application Notes Modules above can be ordered to have an increased bottom side board clearance and a slightly larger total height (see page 2 for dimensions). To order these parts, replace EGL in the part number with EGA. There are no other differences from the EGL units. A variety of application notes and technical white papers can be downloaded in pdf format from our website. The following option choices must be included in place of the w x y z spaces in the model numbers listed above. Options Description: w x y z Thermal Design Enable Logic Pin Length K - 0.110" A - Open Frame P - Positive N - 0.145" L - Low Profile Open Frame N - Negative R - 0.180" Y - 0.250" Feature Set S - Standard T - Alternative Trim Equation Contact SynQor for further information: Phone: Toll Free: Fax: E-mail: Web: Address: Product # PQ60012EGL20 978-849-0600 888-567-9596 978-849-0602 power@synqor.com www.synqor.com 155 Swanson Road Boxborough, MA 01719 USA Phone 1-888-567-9596 Warranty SynQor offers a three (3) year limited warranty. Complete warranty information is listed on our website or is available upon request from SynQor. Information furnished by SynQor is believed to be accurate and reliable. However, no responsibility is assumed by SynQor for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SynQor. www.synqor.com Doc.# 005-2EG621G Rev. B 02/10/06 Page 13