Photomicrosensor (Transmissive) EE-SX461-P11 Dimensions Features * * * * * * Note: All units are in millimeters unless otherwise indicated. 171826-3 (Tyco Electronics AMP) Snap-in-mounting model. Mounts to 0.8- to 1.6-mm-thick panels. With a 15-mm-wide slot. Photo IC output signals directly connect with C-MOS and TTL. Connects to Tyco Electronics AMP's EI-series connectors. RoHS Compliant. Absolute Maximum Ratings (Ta = 25C) Item Two, R1 VCC 7V Optical axis Output voltage VOUT 28 V Output current IOUT 16 mA Permissible output dissipation POUT 250 mW (see note) Ambient temperature Operating Topr -20C to 75C Storage Tstg -40C to 85C Tsol --- Soldering temperature Internal Circuit V Unless otherwise specified, the tolerances are as shown below. Note: Refer to the temperature rating chart if the ambient temperature exceeds 25C. O G Dimensions Terminal No. O G Tolerance 3 < mm 6 0.3 0.375 Power supply (Vcc) 6 < mm 10 0.45 Output (OUT) Ground (GND) 10 < mm 18 0.55 18 < mm 30 0.65 3 mm max. Name Rated value Power supply voltage (15) V Symbol 2 (Aperture width) Ordering Information Description Model Photomicrosensor (transmissive) EE-SX461-P11 Recommended Mating Connectors: Tyco Electronics AMP 171822-3 (crimp connector) 172142-3 (crimp connector) OMRON EE-1005 (with harness) Electrical and Optical Characteristics (Ta = 25C, VCC = 5 V10%) Item Symbol Value Condition ICC 35 mA max. Low-level output voltage VOL 0.3 V max. IOUT = 16 mA with incident High-level output voltage VOH (VCC x 0.9) V min. VOUT = VCC without incident, RL = 47 k Response frequency f 3 kHz min. VOUT = VCC, RL = 47 k (see note) Current consumption With and without incident Note: The value of the response frequency is measured by rotating the disk as shown below. Disk 2.1 mm 0.5 mm 0.5 mm t = 0.2 mm Photomicrosensor (Transmissive) EE-SX461-P11 211 Engineering Data Sensing Position Characteristics (Typical) d2 = 01.1 mm Output transistor Light interrupting plate Center of optical axis VCC = 5 V Ta = 25C RL = 47 k d OFF d2 ON -3 Ambient temperature Ta (C) Center of optical axis Sensing Position Characteristics (Typical) VCC = 5 V Ta = 25C RL = 47 k d1 = 01.1 mm Output transistor Output allowable dissipation Pc (mW) Output Allowable Dissipation vs. Ambient Temperature Characteristics -2 -1 0 1 2 3 Distance d (mm) Distance d (mm) EE-1005 Connector 1,00020 (1) (2) No. (3) Name Model Quantity Maker 1 Receptacle housing 171822-3 1 Tyco Electronics AMP 2 Receptacle contact 170262-1 3 Tyco Electronics AMP 3 Lead wire UL1007 AWG24 3 --- Wiring Connector circuit no. Lead wire color Output when connected to EE-SX461-P11 1 Red VCC 2 Orange OUT 3 Yellow GND Recommended Mounting Hole Dimensions and Mounting and Dismounting Method Dismounting by Hand Squeeze the mounting tabs as shown in the following illustration and press the mounting tabs upwards. Optical axis EE-SX461-P11 Sensor edge (to post header) Center of sensing slot Sensor edge (2) The Photomicrosensor can be mounted to 0.8- to 1.6-mm-thick panels. Refer to the above mounting hole dimensions and open the mounting holes in the panel to which the Photomicrosensor will be mounted. Insert into the holes the Photomicrosensor's mounting portions with a force of three to five kilograms but do not press in the Photomicrosensor at one time. The Photomicrosensor can be easily mounted by inserting the mounting portions halfway and then slowly pressing the Photomicrosensor onto the panel. There are two ways to dismount the Photomicrosensor. Refer to the following. Dismounting with Screwdriver Press the mounting hooks of the Photomicrosensor with a flat-blade screwdriver as shown in the following illustration and pull up the Photomicrosensor. Panel (1) Pressed mounting holes are ideal for mounting the Photomicrosensor. When mounting the Photomicrosensor to a panel that has pressed mounting holes for the Photomicrosensor, be sure to mount the Photomicrosensor on the pressing side of the panel, otherwise it may be difficult to mount the Photomicrosensor and an insertion force of five to six kilograms may be required. When mounting the Photomicrosensor to a panel that has mounting holes opened by pressing, make sure that the mounting holes have no burrs, otherwise the lock mechanism of the Photomicrosensor will not work perfectly. After mounting the Photomicrosensor to a panel, be sure to check if the lock mechanism is working perfectly. EE-SX461-P11 EE-SX461-P11 Flat-blade screwdriver (2) (2) (1) Mounting hook 212 Flat-blade screwdriver (1) Panel Mounting hook Photomicrosensor (Transmissive) (1) This tapered portion must be on the lower side of the panel, otherwise the Photomicrosensor will not be locked in. EE-SX461-P11 Panel Mounting tab MEMO Photomicrosensor (Transmissive) EE-SX461-P11 All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. OMRON ON-LINE OMRON ELECTRONIC COMPONENTS LLC Global - http://www.omron.com USA - http://www.components.omron.com 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 847-882-2288 Cat. No. X305-E-1 10/10 Specifications subject to change without notice Photomicrosensor (Transmissive) EE-SX461-P11 Printed in USA