Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 LPV321-N Single, LPV358-N Dual, and LPV324-N Quad General-Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers 1 Features 3 Description * * * The LPV3xx-N are low power (9-A per channel at 5 V) versions of the LMV3xx op amps. This is another addition to the LMV family of commodity op amps. 1 * * * * * Specified 2.7-V and 5-V Performance No Crossover Distortion Space-Saving Package - 5-Pin SC70 2 x 2.1 x 1 mm Industrial Temperature Range: -40C to 85C Gain-Bandwidth Product: 152 kHz Low Supply Current - LPV321-N: 9 A - LPV358-N: 15 A - LPV324-N: 28 A Rail-to-Rail Output Swing at 100 k Load: - V+ - 3.5 mV - V- + 90 mV VCM, -0.2 V to V+- 0.8 V 2 Applications * * * Active Filters General-Purpose Low Voltage Applications General-Purpose Portable Devices The LPV3xx-N are the most cost effective solutions for the applications where low voltage, low power operation, space saving and low price are needed. The LPV3xx-N have rail-to-rail output swing capability and the input common-mode voltage range includes ground. They all exhibit excellent speed-power ratio, achieving 152 kHz of bandwidth with a supply current of only 9 A. The LPV321-N is available in space saving 5-Pin SC70, which is approximately half the size of 5-Pin SOT-23. The small package saves space on PC boards, and enables the design of small portable electronic devices. It also allows the designer to place the device closer to the signal source to reduce noise pickup and increase signal integrity. The chips are built with Texas Instruments's advanced submicron silicon-gate BiCMOS process. The LPV3xx-N have bipolar input and output stages for improved noise performance and higher output current drive. Device Information(1) PART NUMBER LPV321-N LPV358-N LPV324-N PACKAGE BODY SIZE (NOM) SC70 (5) 2.00 mm x 1.25 mm SOT-23 (5) 2.90 mm x 1.60 mm SOIC (8) 4.90 mm x 3.91 mm VSSOP (8) 3.00 mm x 3.00 mm SOIC (14) 8.65 mm x 3.91 mm TSSOP (14) 5.00 mm x 4.40 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Micropower Supply Current Rail-to-Rail Output Swing 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 4 4 4 4 5 5 5 6 7 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. DC Electrical Characteristics - 2.7 V........................ AC Electrical Characteristics - 2.7 V ........................ DC Electrical Characteristics - 5 V........................... AC Electrical Characteristics - 5 V ........................... Typical Characteristics .............................................. Detailed Description ............................................ 13 7.1 Overview ................................................................ 13 7.2 Functional Block Diagram ....................................... 13 7.3 Feature Description................................................. 13 7.4 Device Functional Modes........................................ 14 8 Application and Implementation ........................ 16 8.1 Application Information .......................................... 16 8.2 Typical Applications ................................................ 16 9 Power Supply Recommendations...................... 19 10 Layout................................................................... 20 10.1 Layout Guidelines ................................................. 20 10.2 Layout Example .................................................... 20 11 Device and Documentation Support ................. 21 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 Device Support .................................................... Documentation Support ....................................... Related Links ........................................................ Receiving Notification of Documentation Updates Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 21 21 21 21 21 21 22 22 12 Mechanical, Packaging, and Orderable Information ........................................................... 22 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision D (March 2013) to Revision E Page * Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .................................................................................................. 1 * Deleted Soldering temperature (235C maximum)................................................................................................................. 4 * Changed Thermal Resistance, RJA, values From: 478 To: 296.7 (SC70), From: 265 To: 206.6 (SOT-23), From: 190 To: 130.1 (8-Pin SOIC), From: 235 To: 187.5 (VSSOP), From: 145 To: 103.9 (14-Pin SOIC), From: 155 To: 132.7 (TSSOP) ................................................................................................................................................................................. 4 Changes from Revision C (March 2013) to Revision D * 2 Page Changed layout of National Semiconductor Data Sheet to TI format .................................................................................... 1 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N LPV321-N, LPV324-N, LPV358-N www.ti.com SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 5 Pin Configuration and Functions DBV or DCK Package 5-Pin SC70 or SOT-23 Top View IN+ 1 V- 2 IN- 3 D or DGK Package 8-Pin SOIC or VSSOP Top View 5 V+ 4 OUT D or PW Package 14-Pin SOIC or TSSOP Top View OUT A 1 8 V+ -IN A 2 7 +IN A 3 V- 4 OUT A 1 14 OUT D OUT B -IN A 2 13 -IN D 6 -IN B +IN A 3 12 +IN D 5 +IN B V+ 4 11 V- +IN B 5 10 +IN C -IN B 6 9 -IN C OUT B 7 8 OUT C Pin Functions PIN SC70 or SOT-23 SOIC or VSSOP SOIC or TSSOP TYPE (1) +IN 1 -- -- I Noninverting input IN A+ -- 3 3 I Noninverting input, channel A IN B+ -- 5 5 I Noninverting input, channel B IN C+ -- -- 10 I Noninverting input, channel C IN D+ -- -- 12 I Noninverting input, channel D -IN 3 -- -- I Inverting input IN A- -- 2 2 I Inverting input, channel A IN B- -- 6 6 I Inverting input, channel B IN C- -- -- 9 I Inverting input, channel C IN D- -- -- 13 I Inverting input, channel D OUTPUT 4 -- -- O Output OUT A -- 1 1 O Output, channel A OUT B -- 7 7 O Output, channel B OUT C -- -- 8 O Output, channel C OUT D -- -- 14 O Output, channel D V+ 5 8 4 P Positive (highest) power supply V- 2 4 11 P Negative (lowest) power supply NAME (1) DESCRIPTION I = Input, O = Output, P = Power Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N Submit Documentation Feedback 3 LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) MIN Differential input voltage MAX Supply voltage (V+- V -) Output short circuit to V + (2) (3) (4) V 150 C 150 C See (3) (4) Storage temperature, Tstg (1) 5.5 See (2) Output short circuit to V - Junction temperature, TJ(MAX) UNIT Supply voltage -65 Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Shorting output to V+ will adversely affect reliability. Shorting output to V- will adversely affect reliability. The maximum power dissipation is a function of TJ(MAX) and RJA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA) / RJA. All numbers apply for packages soldered directly onto a PCB. 6.2 ESD Ratings VALUE UNIT LPV321-N in DBV and DCK Packages V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) 1500 Machine model 100 Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) 1500 Machine model 100 Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) 2000 Machine model 100 V LPV358-N in D and DGK Packages V(ESD) Electrostatic discharge V LPV324-N in D and PW Packages V(ESD) (1) Electrostatic discharge V Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC)Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC). 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT Supply voltage 2.7 5 V Operating temperature -40 85 C 6.4 Thermal Information LPV321-N THERMAL METRIC (1) LPV358-N LPV324-N DBV (SOT-23) DCK (SC70) DGK (VSSOP) D (SOIC) D (SOIC) PW (TSSOP) 5 PINS 5 PINS 8 PINS 8 PINS 14 PINS 14 PINS UNIT RJA Junction-to-ambient thermal resistance 206.6 296.7 187.5 130.1 103.9 132.7 C/W RJC(top) Junction-to-case (top) thermal resistance 167.2 128.1 77.7 74.3 61.6 59.1 C/W RJB Junction-to-board thermal resistance 65.5 74.3 108 70.7 58.4 75.1 C/W JT Junction-to-top characterization parameter 50.2 6.5 15.2 23.1 21.2 10.8 C/W JB Junction-to-board characterization parameter 65.1 73.6 106.5 70.2 58.1 74.58 C/W RJC(bot) Junction-to-case (bottom) thermal resistance -- -- -- -- -- -- C/W (1) 4 For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N LPV321-N, LPV324-N, LPV358-N www.ti.com SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 6.5 DC Electrical Characteristics - 2.7 V TJ = 25C, V+ = 2.7 V, V- = 0 V, VCM = 1 V, VO = V+/2, and R L > 1 M (unless otherwise noted) PARAMETER TEST CONDITIONS MIN (1) TYP (2) MAX (1) 1.2 7 UNIT VOS Input offset voltage TCVOS Input offset voltage average drift IB Input bias current 1.7 50 nA IOS Input offset current 0.6 40 nA CMRR Common mode rejection ratio 0 V VCM 1.7 V 50 70 dB PSRR Power supply rejection ratio 2.7 V V+ 5 V, VO = 1 V, VCM = 1 V 50 65 dB 0 -0.2 VCM Input common-mode voltage For CMRR 50 dB VO Output swing RL = 100 k to 1.35 V IS Supply current V/C 1.9 V+ - 100 V 1.7 V+ - 3 80 mV 180 LPV321-N 4 8 LPV358-N, both amplifiers 8 16 16 24 LPV324-N, all four amplifiers (1) (2) mV 2 A All limits are specified by testing or statistical analysis. Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production material. 6.6 AC Electrical Characteristics - 2.7 V TJ = 25C, V+ = 2.7 V, V- = 0 V, VCM = 1 V, VO = V+/2, and R L > 1 M (unless otherwise noted) PARAMETER TEST CONDITIONS MIN (1) TYP (2) UNIT GBWP Gain-bandwidth product m Phase margin Gm Gain margin 35 dB en Input-referred voltage noise f = 1 kHz 178 nV/Hz in Input-referred current noise f = 1 kHz 0.5 pA/Hz (1) (2) CL = 22 pF MAX (1) 112 kHz 97 All limits are specified by testing or statistical analysis. Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production material. 6.7 DC Electrical Characteristics - 5 V TJ = 25C, V+ = 5 V, V- = 0 V, VCM = 2 V, VO = V+/2, and R L > 1 M (unless otherwise noted) PARAMETER VOS Input offset voltage TCVOS Input offset voltage average drift IB Input bias current IOS Input offset current CMRR Common mode rejection ratio PSRR (1) (2) Power supply rejection ratio TEST CONDITIONS MIN (1) TJ = 25C TYP (2) MAX (1) 1.5 7 TJ = -40C to 85C 10 2 TJ = 25C 2 TJ = -40C to 85C 0.6 TJ = -40C to 85C 0 V VCM 4 V + 2.7 V V 5 V, VO = 1 V, VCM = 1 V mV V/C 50 60 TJ = 25C UNIT 40 50 nA nA 50 71 dB 50 65 dB All limits are specified by testing or statistical analysis. Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production material. Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N Submit Documentation Feedback 5 LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 www.ti.com DC Electrical Characteristics - 5 V (continued) TJ = 25C, V+ = 5 V, V- = 0 V, VCM = 2 V, VO = V+/2, and R L > 1 M (unless otherwise noted) PARAMETER TEST CONDITIONS VCM Input common-mode voltage For CMRR 50 dB AV Large signal voltage gain (3) RL = 100 k VO Output short circuit current sourcing IO Output short circuit current sinking (3) Supply current 0 -0.2 TJ = 25C 15 TJ = -40C to 85C 10 TJ = 25C Sinking RL = 100 k to 2.5 V TJ = 25C MAX (1) V+ -100 90 180 mV 220 16 LPV321-N, VO = 5 V 20 60 11 16 LPV324-N and LPV358-N, VO = 5 V TJ = 25C 9 TJ = -40C to 85C TJ = 25C V/mV V -200 2 LPV324-N, All four amplifiers V V+ -3.5 TJ = -40C to 85C TJ = 25C UNIT + TJ = -40C to 85C LPV358-N, Both amplifiers 4 100 LPV3xx-N, VO = 0 V LPV321-N IS TYP (2) 4.2 Sourcing RL = 100 k to 2.5 V Output swing MIN (1) mA 12 15 15 TJ = -40C to 85C 20 24 28 TJ = -40C to 85C A 42 46 - RL is connected to V . The output voltage is 0.5 V VO 4.5 V. 6.8 AC Electrical Characteristics - 5 V TJ = 25C, V+ = 5 V, V- = 0 V, VCM = 2 V, VO = V+/2, and R L > 1M (unless otherwise noted) PARAMETER TEST CONDITIONS MIN (1) (3) TYP (2) MAX (1) UNIT SR Slew rate GBWP Gain-bandwidth product m Phase margin Gm Gain margin 19 dB en Input-referred voltage noise f = 1 kHz 146 nV/Hz in Input-referred current noise f = 1 kHz 0.3 pA/Hz (1) (2) (3) 6 CL = 22 pF 0.1 V/s 152 kHz 87 All limits are specified by testing or statistical analysis. Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped production material. Connected as voltage follower with 3V step input. Number specified is the slower of the positive and negative slew rates. Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N LPV321-N, LPV324-N, LPV358-N www.ti.com SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 6.9 Typical Characteristics VS = 5 V, single supply, and TA = 25C (unless otherwise noted) Figure 1. Supply Current vs Supply Voltage (LPV321-N) Figure 2. Input Current vs Temperature Figure 3. Sourcing Current vs Output Voltage Figure 4. Sourcing Current vs Output Voltage Figure 5. Sinking Current vs Output Voltage Figure 6. Sinking Current vs Output Voltage Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N Submit Documentation Feedback 7 LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 www.ti.com Typical Characteristics (continued) VS = 5 V, single supply, and TA = 25C (unless otherwise noted) Figure 7. Output Voltage Swing vs Supply Voltage Figure 8. Input Voltage Noise vs Frequency 8 Figure 9. Input Current Noise vs Frequency Figure 10. Input Current Noise vs Frequency Figure 11. Crosstalk Rejection vs Frequency Figure 12. PSRR vs Frequency Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N LPV321-N, LPV324-N, LPV358-N www.ti.com SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 Typical Characteristics (continued) VS = 5 V, single supply, and TA = 25C (unless otherwise noted) Figure 13. CMRR vs Frequency Figure 14. CMRR vs Input Common Mode Voltage Figure 15. CMRR vs Input Common Mode Voltage Figure 16. VOS vs VCM Figure 17. VOS vs VCM Figure 18. Input Voltage vs Output Voltage Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N Submit Documentation Feedback 9 LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 www.ti.com Typical Characteristics (continued) VS = 5 V, single supply, and TA = 25C (unless otherwise noted) 10 Figure 19. Input Voltage vs Output Voltage Figure 20. Open-Loop Frequency Response Figure 21. Open-Loop Frequency Response Figure 22. Gain and Phase vs Capacitive Load Figure 23. Gain and Phase vs Capacitive Load Figure 24. Slew Rate vs Supply Voltage Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N LPV321-N, LPV324-N, LPV358-N www.ti.com SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 Typical Characteristics (continued) VS = 5 V, single supply, and TA = 25C (unless otherwise noted) Figure 25. Noninverting Large Signal Pulse Response Figure 26. Noninverting Small Signal Pulse Response Figure 27. Inverting Large Signal Pulse Response Figure 28. Inverting Small Signal Pulse Response Figure 29. Stability vs Capacitive Load Figure 30. Stability vs Capacitive Load Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N Submit Documentation Feedback 11 LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 www.ti.com Typical Characteristics (continued) VS = 5 V, single supply, and TA = 25C (unless otherwise noted) 12 Figure 31. Stability vs Capacitive Load Figure 32. Stability vs Capacitive Load Figure 33. THD vs Frequency Figure 34. Open-Loop Output Impedance vs Frequency Figure 35. Short Circuit Current vs Temperature (Sinking) Figure 36. Short Circuit Current vs Temperature (Sourcing) Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N LPV321-N, LPV324-N, LPV358-N www.ti.com SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 7 Detailed Description 7.1 Overview The LPV321-N, LPV358-N, and LPV324-N devices are micropower (10-A) versions of the popular LMV3xx-N. The LPV321-N is the single-channel version. The LPV358-N is the dual, and the LPV324-N is the quad. The LPV32x-N are the most cost effective solution for applications where low power and low voltage operation, space efficiency, and low-price are important. The LPV3x-N have rail-to-rail output swing capability and the input common-mode voltage range includes ground. They all exhibit excellent speed to power ratio, achieving 152 kHz of bandwidth and 0.1-V/s slew rate with 10 mA of supply current. 7.2 Functional Block Diagram V IN - IN + + _ OUT + V - Copyright (c) 2016, Texas Instruments Incorporated 7.3 Feature Description 7.3.1 Size The small footprints of the LPV3xx-N packages save space on printed circuit boards, and enable the design of smaller electronic products (such as cellular phones, pagers, or other portable systems). The low profile of the LPV3xx-N make them possible to use in PCMCIA type III cards. 7.3.2 Signal Integrity Signals can pick up noise between the signal source and the amplifier. By using a physically smaller amplifier package, the LPV3xx-N can be placed closer to the signal source, reducing noise pickup and increasing signal integrity. 7.3.3 Simplified Board Layout These products help avoid using long printed-circuit traces in the PCB. This means no additional components, such as capacitors and resistors, are needed to filter out unwanted signals due to the interference between the long printed-circuit traces. 7.3.4 Low Supply Current These devices help maximize battery life. They are ideal for battery powered systems. 7.3.5 Low Supply Voltage TI provides ensured performance at 2.7 V and 5 V. These specifications ensure operation throughout the battery lifetime. 7.3.6 Rail-to-Rail Output Rail-to-rail output swing provides maximum possible dynamic range at the output. This is particularly important when operating on low-supply voltages. Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N Submit Documentation Feedback 13 LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 www.ti.com Feature Description (continued) 7.3.7 Input Includes Ground Allows direct sensing near GND in single supply operation. The differential input voltage may be larger than V+ without damaging the device. Protection should be provided to prevent the input voltages from going negative more than -0.3 V (at 25C). An input clamp diode with a resistor to the IC input terminal can be used. 7.4 Device Functional Modes The LPV3xx-N can be operated as a single-supply or a dual-supply operational amplifier depending on the application. 7.4.1 Capacitive Load Tolerance The LPV3xx-N can directly drive 200 pF in unity-gain without oscillation. The unity-gain follower is the most sensitive configuration to capacitive loading. Direct capacitive loading reduces the phase margin of amplifiers. The combination of the amplifier's output impedance and the capacitive load induces phase lag. This results in either an underdamped pulse response or oscillation. To drive a heavier capacitive load, circuit in Figure 37 can be used. Figure 37. Indirectly Driving A Capacitive Load Using Resistive Isolation In Figure 37, the isolation resistor (RISO) and the load capacitor (CL) form a pole to increase stability by adding more phase margin to the overall system. The desired performance depends on the value of RISO. The bigger the RISO resistor value, the more stable VOUT is. Figure 38 is an output waveform of Figure 37 using 100 k for RISO and 1000 pF for CL. Figure 38. Pulse Response of the LPV324 Circuit in Figure 37 14 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N LPV321-N, LPV324-N, LPV358-N www.ti.com SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 Device Functional Modes (continued) The circuit in Figure 39 is an improvement to the one in Figure 37 because it provides DC accuracy as well as AC stability. If there were a load resistor in Figure 37, the output would be voltage divided by RISO and the load resistor. Instead, in Figure 39, RF provides the DC accuracy by using feed-forward techniques to connect VIN to RL. Caution is needed in choosing the value of RF due to the input bias current of the LPV3xx-N. CF and RISO serve to counteract the loss of phase margin by feeding the high frequency component of the output signal back to the amplifier's inverting input, thereby preserving phase margin in the overall feedback loop. Increased capacitive drive is possible by increasing the value of CF. This in turn slows down the pulse response. Figure 39. Indirectly Driving A Capacitive Load With DC Accuracy 7.4.2 Input Bias Current Cancellation The LPV3xx-N family has a bipolar input stage. The typical input bias current of LPV3xx-N is 1.5 nA with 5-V supply. Thus a 100-k input resistor causes 0.15 mV of error voltage. By balancing the resistor values at both inverting and noninverting inputs, the error caused by the amplifier's input bias current is reduced. The circuit in Figure 40 shows how to cancel the error caused by input bias current. Figure 40. Cancelling the Error Caused by Input Bias Current Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N Submit Documentation Feedback 15 LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 www.ti.com 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information The LPV3xx-N family of amplifiers is specified for operation from 2.7 V to 5 V (1.35 V to 2.5 V). Many of the specifications apply from -40C to 125C. They provide ground-sensing inputs as well as rail-to-rail output swing. Parameters that can exhibit significant variance with regard to operating voltage or temperature are presented in the Typical Characteristics. 8.2 Typical Applications 8.2.1 Simple Low-Pass Active Filter A simple low-pass filter is shown in Figure 41. Figure 41. Simple Low-Pass Active Filter Schematic 8.2.1.1 Design Requirements The low-pass filter is shown in Figure 41 passes low frequencies and attenuate frequencies above corner frequency (fc) at a roll-off rate of 20 dB/Decade. 8.2.1.2 Detailed Design Procedure The low-frequency gain ( o) is defined by -R3/R1. This allows low-frequency gains other than unity to be obtained. The filter has a -20 dB/decade roll-off after its corner frequency fc. R2 must be chosen equal to the parallel combination of R1 and R3 to minimize errors due to bais current. The frequency response of the filter is shown in Figure 42. R3 AL R1 16 fc 1 2SR3C1 R2 R1 II R3 Submit Documentation Feedback (1) Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N LPV321-N, LPV324-N, LPV358-N www.ti.com SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 Typical Applications (continued) Note that the single op amp active filters are used in to the applications that require low quality factor, Q ( 10), low frequency ( 5 kHz), and low gain ( 10), or a small value for the product of gain times Q ( 100). The op amp must have an open loop voltage gain at the highest frequency of interest at least 50 times larger than the gain of the filter at this frequency. In addition, the selected op amp must have a slew rate that meets the requirements in Equation 2. Slew Rate 0.5 x (HV OPP) x 10-6V/sec where * * H is the highest frequency of interest VOPP is the output peak-to-peak voltage (2) 8.2.1.3 Application Curve Figure 42. Frequency Response of Simple Low-pass Active Filter 8.2.2 Difference Amplifier The difference amplifier allows the subtraction of two voltages or, as a special case, the cancellation of a signal common to two inputs. It is useful as a computational amplifier in making a differential to single-ended conversion or in rejecting a common mode signal. Figure 43. Difference Amplifier Schematic R2 R1 R2 * R4 R1 R2 * R3 V R3 R4 R1 V2 R1 V1 R3 R4 R1 u 2 (c) (c) for R1 R3 and R2 R4 VOUT VOUT R2 V2 R1 V1 V 2 (3) 8.2.3 Instrumentation Circuits The input impedance of the previous difference amplifier is set by the resistor R1, R2, R3, and R4. To eliminate the problems of low input impedance, one way is to use a voltage follower ahead of each input as shown in the following two instrumentation amplifiers. Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N Submit Documentation Feedback 17 LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 www.ti.com Typical Applications (continued) 8.2.3.1 Three Operating Amplifier Instrumentation The quad LPV324 can be used to build a three-op-amp instrumentation amplifier as shown in Figure 44 Figure 44. Three-op-amp Instrumentation Amplifier Schematic The first stage of this instrumentation amplifier is a differential-input, differential-output amplifier, with two voltage followers. These two voltage followers assure that the input impedance is over 100 M. The gain of this instrumentation amplifier is set by the ratio of R2/R1. R3 should equal R1 and R4 equal R2. Matching of R3 to R1 and R4 to R2 affects the CMRR. For good CMRR over temperature, low drift resistors should be used. Making R4 Slightly smaller than R 2 and adding a trim pot equal to twice the difference between R 2 and R4 will allow the CMRR to be adjusted for optimum. 8.2.3.2 Two Operating Amplifier Instrumentation A two-op-amp instrumentation amplifier can also be used to make a high-input-impedance DC differential amplifier (Figure 45). As in the three-op-amp circuit, this instrumentation amplifier requires precise resistor matching for good CMRR. R4 should equal to R1 and R3 must equal R2. Figure 45. Two-op-amp Instrumentation Amplifier Schematic R4 * 1 R3 V2 V1 ,where R1 R4 and R2 R3 (c) As shown : VO 2 V2 V1 VO (4) 8.2.3.3 Single-Supply Inverting Amplifier There may be cases where the input signal going into the amplifier is negative. Because the amplifier is operating in single supply voltage, a voltage divider using R3 and R4 is implemented to bias the amplifier so the input signal is within the input common-common voltage range of the amplifier. The capacitor C1 is placed between the inverting input and resistor R1 to block the DC signal going into the AC signal source, VIN. The values of R1 and C1 affect the cutoff frequency in Equation 5. fc = 1/2 R 1C1 18 Submit Documentation Feedback (5) Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N LPV321-N, LPV324-N, LPV358-N www.ti.com SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 Typical Applications (continued) As a result, the output signal is centered around mid-supply (if the voltage divider provides V+/2 at the noninverting input). The output can swing to both rails, maximizing the signal-to-noise ratio in a low voltage system. Figure 46. Single-Supply Inverting Amplifier VOUT R2 VIN R1 (6) 9 Power Supply Recommendations The LPV3xx-N is specified for operation from 2.7 V to 5.5 V; many specifications apply from -40C to 125C. Parameters that can exhibit significant variance with regard to operating voltage or temperature are presented in the Typical Characteristics. Place 0.1-F bypass capacitors close to the power-supply pins to reduce errors coupling in from noisy or high impedance power supplies. For more detailed information on bypass capacitor placement, see Layout Guidelines section. Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N Submit Documentation Feedback 19 LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 www.ti.com 10 Layout 10.1 Layout Guidelines For best operational performance, use good PCB layout practices including: * Noise can propagate into analog circuitry through the power pins of the circuit as a whole and the operational amplifier. Bypass capacitors are used to reduce the coupled noise by providing low impedance power sources local to the analog circuitry. * Connect low-ESR, 0.1-F ceramic bypass capacitors between each supply pin and ground, placed as close to the device as possible. A single bypass capacitor from V+ to ground is applicable for single supply applications. * Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effective methods of noise suppression. One or more layers on multilayer PCBs are usually devoted to ground planes. A ground plane helps distribute heat and reduces EMI noise pickup. Make sure to physically separate digital and analog grounds, paying attention to the flow of the ground current. For more detailed information, see Circuit Board Layout Techniques (SLOA089). * To reduce parasitic coupling, run the input traces as far away from the supply or output traces as possible. If it is not possible to keep them separate, it is much better to cross the sensitive trace perpendicular as opposed to in parallel with the noisy trace. * Place the external components as close to the device as possible. Keeping RF and RG close to the inverting input minimizes parasitic capacitance, as shown in Figure 47. * Keep the length of input traces as short as possible. Always remember that the input traces are the most sensitive part of the circuit. * Consider a driven, low-impedance guard ring around the critical traces. A guard ring can significantly reduce leakage currents from nearby traces that are at different potentials. 10.2 Layout Example Figure 47. Operational Amplifier Board Layout for Noninverting Configuration 20 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N LPV321-N, LPV324-N, LPV358-N www.ti.com SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 11 Device and Documentation Support 11.1 Device Support 11.1.1 Development Support * LPV321-N PSPICE Model (SNOM026) * LPV358-N PSPICE Model (SNOM022) * LPV324-N PSPICE Model (SNOM027) * TINA-TI SPICE-Based Analog Simulation Program * DIP Adapter Evaluation Module * TI Universal Operational Amplifier Evaluation Module * TI Filterpro Software 11.2 Documentation Support 11.2.1 Related Documentation For related documentation see the following: * Handbook of Operational Amplifier Applications (SBOA092) * Compensate Transimpedance Amplifiers Intuitively (SBOA055) * Circuit Board Layout Techniques (SLOA089) * AN-1803 Design Considerations for a Transimpedance Amplifier (SNOA515) 11.3 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 1. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY LPV321-N Click here Click here Click here Click here Click here LPV324-N Click here Click here Click here Click here Click here LPV358-N Click here Click here Click here Click here Click here 11.4 Receiving Notification of Documentation Updates To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. 11.5 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.6 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N Submit Documentation Feedback 21 LPV321-N, LPV324-N, LPV358-N SNOS413E - AUGUST 2000 - REVISED NOVEMBER 2016 www.ti.com 11.7 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.8 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 22 Submit Documentation Feedback Copyright (c) 2000-2016, Texas Instruments Incorporated Product Folder Links: LPV321-N LPV324-N LPV358-N PACKAGE OPTION ADDENDUM www.ti.com 27-Sep-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LPV321M5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 A27A LPV321M5X/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 A27A LPV321M7 NRND SC70 DCK 5 1000 TBD Call TI Call TI -40 to 85 A19 LPV321M7/NOPB ACTIVE SC70 DCK 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 A19 LPV321M7X/NOPB ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 A19 LPV324M/NOPB ACTIVE SOIC D 14 55 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LPV324M LPV324MT/NOPB ACTIVE TSSOP PW 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LPV324 MT LPV324MTX NRND TSSOP PW 14 2500 TBD Call TI Call TI -40 to 85 LPV324 MT LPV324MTX/NOPB ACTIVE TSSOP PW 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LPV324 MT LPV324MX NRND SOIC D 14 2500 TBD Call TI Call TI -40 to 85 LPV324M LPV324MX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LPV324M LPV358M/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM LPV358MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 P358 LPV358MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 P358 LPV358MX NRND SOIC D 8 2500 TBD Call TI Call TI -40 to 85 LPV 358M LPV358MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LPV 358M (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. Addendum-Page 1 LPV 358M Samples PACKAGE OPTION ADDENDUM www.ti.com 27-Sep-2017 PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ LPV321M5/NOPB SOT-23 LPV321M5X/NOPB LPV321M7 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 3.2 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.2 1.4 4.0 8.0 Q3 DBV 5 1000 178.0 8.4 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 SC70 DCK 5 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LPV321M7/NOPB SC70 DCK 5 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LPV321M7X/NOPB SC70 DCK 5 3000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LPV324MTX TSSOP PW 14 2500 330.0 12.4 6.95 5.6 1.6 8.0 12.0 Q1 LPV324MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.95 5.6 1.6 8.0 12.0 Q1 LPV324MX SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 LPV324MX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 LPV358MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LPV358MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LPV358MX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LPV358MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LPV321M5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LPV321M5X/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LPV321M7 SC70 DCK 5 1000 210.0 185.0 35.0 LPV321M7/NOPB SC70 DCK 5 1000 210.0 185.0 35.0 LPV321M7X/NOPB SC70 DCK 5 3000 210.0 185.0 35.0 LPV324MTX TSSOP PW 14 2500 367.0 367.0 35.0 LPV324MTX/NOPB TSSOP PW 14 2500 367.0 367.0 35.0 LPV324MX SOIC D 14 2500 367.0 367.0 35.0 LPV324MX/NOPB SOIC D 14 2500 367.0 367.0 35.0 LPV358MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LPV358MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 LPV358MX SOIC D 8 2500 367.0 367.0 35.0 LPV358MX/NOPB SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 1.75 1.45 PIN 1 INDEX AREA 1 0.1 C B A 5 2X 0.95 1.9 1.45 MAX 3.05 2.75 1.9 2 4 0.5 5X 0.3 0.2 3 (1.1) C A B 0.15 TYP 0.00 0.25 GAGE PLANE 8 TYP 0 0.22 TYP 0.08 0.6 TYP 0.3 SEATING PLANE 4214839/C 04/2017 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. www.ti.com EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MIN ARROUND 0.07 MAX ARROUND NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4214839/C 04/2017 NOTES: (continued) 4. Publication IPC-7351 may have alternate designs. 5. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X(0.95) 4 3 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/C 04/2017 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 7. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LPV358M/NOPB LPV358MM LPV358MM/NOPB LPV358MMX/NOPB LPV358MX LPV358MX/NOPB