MIC33050 4MHz Internal Inductor PWM Buck Regulator with HyperLight Load(R) General Description Features The Micrel MIC33050 is a high-efficiency 600mA PWM Input voltage: 2.7V to 5.5V synchronous buck (step-down) regulator with internal 600mA output current inductor featuring HyperLight Load, a patent-pending Fixed and adjustable output voltage options switching scheme that offers best-in-class light load No external inductor required efficiency and transient performance while providing very Ultra-fast transient response small external components and low output ripple at all 20A quiescent current loads. 4MHz switching in PWM mode The MIC33050 also has a very-low typical quiescent Low output voltage ripple current of 20A and can achieve over 85% efficiency even >93% peak efficiency at 1mA. >85% efficiency at 1mA In contrast to traditional light load schemes, the HyperLight Micropower shutdown Load architecture does not trade off control speed to obtain low standby currents and in doing so, the device 12-pin 3mm x 3mm MLF(R) only needs a small output capacitor to absorb the load -40C to +125C junction temperature range transient as the powered device goes from light load to full load. Applications At higher loads, the MIC33050 provides a constant switching frequency of greater than 4MHz while providing Cellular phones peak efficiencies greater than 93%. Digital cameras The MIC33050 is available in fixed and adjustable output Portable media players voltages and comes in a 12-pin 3mm x 3mm MLF(R) with a Wireless LAN cards junction operating range of -40C to +125C. WiFi, WiMax, and WiBro modules Data sheets and support documentation can be found on USB-powered devices Micrel's web site at: www.micrel.com. ____________________________________________________________________________________________________________ Typical Application HyperLight Load is a registered trademark of Micrel, Inc. MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc. Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com May 2012 M9999-050312-C Micrel, Inc. MIC33050 Ordering Information Part Number Voltage Temperature Range Package Lead Finish (R) Pb-Free MIC33050-CYHL 1.0V -40 to +125C 12-Pin 3mm x 3mm MLF MIC33050-4YHL 1.2V -40 to +125C 12-Pin 3mm x 3mm MLF(R) Pb-Free -40 to +125C (R) Pb-Free 12-Pin 3mm x 3mm MLF (R) Pb-Free 12-Pin 3mm x 3mm MLF (R) Pb-Free MIC33050-GYHL 1.8V MIC33050-SYHL 3.3V MIC33050-AYHL -40 to +125C ADJ -40 to +125C 12-Pin 3mm x 3mm MLF Notes: 1. Other output voltage options available. Please contact Micrel for details. 2. MLF is a green RoHS-compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free. (R) Pin Configuration 12-Pin 3mm x 3mm MLF(R) (HL) Fixed Output 12-Pin 3mm x 3mm MLF(R) (HL) Adjustable Output Top View Top View Pin Description Pin Number (Fixed) Pin Number (Adj) Pin Name 1 1 VIN Pin Function Supply Voltage (Input): Requires bypass capacitor-to-GND. 2 2 PGND 3, 4, 5, 6 3, 4, 5, 6 SW Switch (Output): Internal power MOSFET output switches. 7, 8 7, 8 OUT Output after the internal inductor. 9 9 EN 10 10 SNS Input to the error amplifier. Connect to the external resistor divider network to see the output voltage. For fixed output voltages connect VOUT (internal resistor network sets the output voltage). 11 - CFF Feed forward capacitor connected to out sense pin. - 11 FB 12 12 AGND Analog ground. EP EP ePad Exposed Heatsink Pad. Connect to power ground for best thermal performance. May 2012 Power Ground. Enable (Input): Logic low will shut down the device, reducing the quiescent current to less than 4A. Do not leave floating. Feedback voltage. Connect a resistor divider from output to ground to set the output voltage. 2 M9999-050312-C Micrel, Inc. MIC33050 Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VIN) .........................................................6V Output Switch Voltage (VSW) ............................................6V Output Switch Current (ISW)..............................................2A Logic Input Voltage (VEN) .................................. -0.3V to VIN Storage Temperature Range (Ts)..............-65C to +150C ESD Rating(3) ................................................. ESD Sensitive Supply Voltage (VIN)......................................... 2.7V to 5.5V Logic Input Voltage (VEN)..............................-0.3V to VIN Junction Temperature (TJ) ..................-40C TJ +125C Thermal Resistance 3mm x 3mm MLF(R)-12 (JA)................................60C/W Electrical Characteristics(4) TA = 25C with VIN = VEN = 3.6V; CFF = 560pF; COUT = 4.7F; IOUT = 20mA unless otherwise specified. Bold values indicate -40C< TJ < +125C. Parameter Supply Voltage Range Undervoltage Lockout Threshold UVLO Hysteresis Quiescent Current, Hyper LL mode Shutdown Current Output Voltage Accuracy Current Limit in PWM Mode Output Voltage Line Regulation Output Voltage Load Regulation Feedback Voltage Maximum Duty Cycle PWM Switch ON-Resistance Frequency Soft-Start Time Enable Threshold Enable Hysteresis Enable Input Current Over-temperature Shutdown Over-temperature Shutdown Hysteresis Condition Min. (turn-on) 2.7 2.45 IOUT = 0mA ; VSNS > 1.2*VOUT nominal VIN = 5.5V; VEN = 0V VIN = 3.0V; ILOAD = 20mA SNS = 0.9*VNOM VIN = 3.0V to 5.5V; ILOAD = 20mA 20mA < ILOAD < 500mA, VIN = 3.0V; IOUT = 20mA SNS VNOM ISW = 100mA PMOS ISW = -100mA NMOS ILOAD = 120mA VOUT = 90% (turn-on) Typ. Max. Units 2.55 5.5 2.65 V V 100 20 0.01 -2.5 0.65 390 80 0.5 1 0.5 0.3 400 89 0.45 0.5 4 650 0.8 35 0.1 165 20 32 4 +2.5 1.7 410 mV A A % A %/V % mV % 1.2 2 MHz s V mV A C C Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. 4. Specification for packaged product only. May 2012 3 M9999-050312-C Micrel, Inc. MIC33050 Typical Characteristics Efficiency VOUT = 3.3V 100 100 100 80 V IN 70 V 90 V = 5.0V IN = 5.5V 60 IN = 3.0V 90 EFFICIENCY (%) IN 90 = 4.2V EFFICIENCY (%) V EFFICIENCY (%) Efficiency VOUT = 1.2V Efficiency VOUT = 1.8V 80 70 V IN V = 3.6V IN = 4.2V 50 1 50 1 10 100 1000 OUTPUT CURRENT (mA) Efficiency VOUT = 1.0V 70 Quiescent Current vs. Temperature 40 VIN = 3.6V 10 100 1000 OUTPUT CURRENT (mA) Quiescent Current vs. Input Voltage = 2.7V 80 70 VIN = 4.2V L = 1uH 50 1 10 100 1000 OUTPUT CURRENT (mA) QUIESCENT CURRENT (A) IN QUIESCENT CURRENT (uA) V 60 VIN = 3.6V 30 20 10 VIN = 3.6V VOUT = 1.8V 45 40 35 30 25 20 VIN = 3.6V VOUT = 1.8V No Load 15 10 5 0 0 -40 -20 0 20 40 60 80 100 2.7 120 3.2 Switching Frequency vs. Input Voltage Switching Frequency vs. Temperature 5 4.5 4 3.5 VIN = 3.6V VOUT = 1.8V Load = 150mA 3 2.5 -20 0 20 40 60 80 TEMPERATURE (C) May 2012 100 120 5.50 4.7 5.2 0.5 5.00 4.50 4.00 3.50 VIN = 3.6V VOUT = 1.8V Load = 150mA 3.00 2.50 2.70 4.2 Feedback Voltage vs. Temperature FEEDBACK VOLTAGE (V) SWITCHING FREQUENCY (MHz) 5.5 3.7 INPUT VOLTAGE (V) TEMPERATURE (C) SWITCHING FREQUENCY (MHz) VIN = 4.2V 50 90 -40 = 2.7V 80 50 1 10 100 1000 OUTPUT CURRENT (mA) 100 EFFICIENCY (%) IN 60 60 V 0.48 0.46 0.44 0.42 0.4 0.38 0.36 VIN = 3.6V VOUT = 1.8V No Load 0.34 0.32 0.3 3.20 3.70 4.20 4.70 INPUT VOLTAGE (V) 4 5.20 -40 -20 0 20 40 60 80 100 120 TEMPERATURE (C) M9999-050312-C Micrel, Inc. MIC33050 Typical Characteristics (Continued) Output Voltage vs. Temperature Output Voltage vs. Input Voltage (V) 1.9 1.90 Output Voltage vs. Output Current 1.85 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 1.9 1.8 VIN = 3.6V VOUT = 1.8V No Load 1.75 1.7 1.85 1.85 1.80 1.8 1.75 1.75 Load = 20mA 1.70 0 1.7 -40 -20 0 20 40 60 80 TEMPERATURE (C) May 2012 100 120 2.7 3.2 3.7 4.2 4.7 5.2 VIN = 3.6V 100 200 300 400 500 600 OUTPUT CURRENT (mA) INPUT VOLTAGE (V) 5 M9999-050312-C Micrel, Inc. MIC33050 Functional Characteristics May 2012 6 M9999-050312-C Micrel, Inc. MIC33050 Functional Characteristics (Continued) May 2012 7 M9999-050312-C Micrel, Inc. MIC33050 Functional Diagram MIC33050 Fixed Output Block Diagram MIC33050 Adjustable Output Block Diagram May 2012 8 M9999-050312-C Micrel, Inc. MIC33050 Functional Description CFF The CFF pin is connected to the SNS pin of MIC33050 with a feed-forward capacitor of 560pF. The CFF pin itself is compared with the internal reference voltage (VREF) of the device and provides the control path to control the output. VREF is equal to 400mV. The CFF pin is sensitive to noise and should be place away from the SW pin. Refer to the layout recommendations for details. VIN VIN provides power to the MOSFETs for the switch mode regulator section and to the analog supply circuitry. Due to the high switching speeds, it is recommended that a 2.2F or greater capacitor be placed close to VIN and the power ground (PGND) pin for bypassing. Refer to the PCB Layout Recommendations for details. EN The enable pin, EN, controls the on and off state of the device. A high logic on the enable pin activates the regulator while a low logic deactivates it. MIC33050 features built-in soft-start circuitry that reduces in-rush current and prevents the output voltage from overshooting at start-up. Do not leave floating. FB The feedback pin is provided for the adjustable output version. An external resistor divider network is connected from the output and is compared to the internal 400mV internal reference voltage within the control loop. The output voltage, of the circuit below, may be calculated via the following equation: SW The pins at the switch node, SW, connect directly to the internal inductor which provides the switching current necessary to operate in PWM mode. Due to the highspeed switching on this pin, the switch node should be routed away from sensitive nodes such as the CFF and FB pins. OUT The OUT pin is for the output voltage following the internal inductor of the device. Connect an output filter capacitor equal to 2.2F or greater to this pin. R1 VOUT 0.4V 1 R2 SNS The sense pin, SNS, is needed to sense the output voltage at the output filter capacitor. In order for the control loop to monitor the output voltage accurately it is good practice to sense the output voltage at the positive side of the output filter capacitor where voltage ripple is smallest. PGND Power ground (PGND) is the ground path for high current. The current loop for the power ground should be as small as possible and separate from the analog ground (AGND) loop. Refer to the PCB Layout Recommendations for more details. AGND Signal ground (AGND) is the ground path for the biasing and control circuitry. The current loop for the signal ground should be separate from the PGND loop. Refer to the PCB Layout Recommendations for more details. May 2012 9 M9999-050312-C Micrel, Inc. MIC33050 Applications Information Input Capacitor A minimum of 2.2F ceramic capacitor should be placed close to the VIN pin and PGND pin for bypassing. X5R or X7R dielectrics are recommended for the input capacitor. Y5V dielectrics, aside from losing most of their capacitance over temperature, they also become resistive at high frequencies. This reduces their ability to filter out high frequency noise. Efficiency VOUT = 1.8V 100 EFFICIENCY (%) 90 Output Capacitor The MIC33050 was designed for use with a 2.2F or greater ceramic output capacitor. A low equivalent series resistance (ESR) ceramic output capacitor either X7R or X5R is recommended. Y5V and Z5U dielectric capacitors, aside from the undesirable effect of their wide variation in capacitance over temperature, become resistive at high frequencies. 70 V = 3.6V IN 50 1 VIN = 4.2V 10 100 1000 OUTPUT CURRENT (mA) The Figure above shows an efficiency curve. From 1A to 100mA, efficiency losses are dominated by quiescent current losses, gate drive and transition losses. By using the HyperLight Load(R) mode, the MIC33050 is able to maintain high efficiency at low output currents. Over 100mA, efficiency loss is dominated by MOSFET RDSON and inductor losses. Higher input supply voltages will increase the Gate-to-Source threshold on the internal MOSFETs, thereby reducing the internal RDSON. This improves efficiency by reducing DC losses in the device. All but the inductor losses are inherent to the device. In which case, inductor selection becomes increasingly critical in efficiency calculations. As the inductors are reduced in size, the DC resistance (DCR) can become quite significant. The DCR losses can be calculated as follows: LPD = IOUT2 x DCR Efficiency Considerations Efficiency is defined as the amount of useful output power, divided by the amount of power supplied. 100 Maintaining high efficiency serves two purposes. It reduces power dissipation in the power supply, reducing the need for heat sinks and thermal design considerations and it reduces consumption of current for battery powered applications. Reduced current draw from a battery increases the devices operating time and is critical in hand held devices. There are two types of losses in switching converters; DC losses and switching losses. DC losses are simply the power dissipation of I2R. Power is dissipated in the high side switch during the on cycle. Power loss is equal to the high side MOSFET RDSON multiplied by the square of the Switch Current. During the off cycle, the low side Nchannel MOSFET conducts, also dissipating power. Device operating current also reduces efficiency. The product of the quiescent (operating) current and the supply voltage is another DC loss. The current required driving the gates on and off at a constant 4MHz frequency and the switching transitions make up the switching losses. May 2012 80 60 Compensation The MIC33050 is designed to be stable with an internal inductor with a minimum of 2.2F ceramic (X5R) output capacitor. V I Efficiency (%) OUT OUT VIN I IN VIN = 3.0V From that, the loss in efficiency due to inductor resistance can be calculated as follows; VOUT I OUT Efficiency Loss (%) 1 VOUT I OUT L PD 100 Efficiency loss due to DCR is minimal at light loads and gains significance as the load is increased. Inductor selection becomes a trade-off between efficiency and size in this case. 10 M9999-050312-C Micrel, Inc. MIC33050 HyperLight Load Mode The MIC33050 uses a minimum on and off time proprietary control loop. When the output voltage falls below the regulation threshold, the error comparator begins a switching cycle that turns the PMOS on and keeps it on for the duration of the minimum-on-time. When the output voltage is over the regulation threshold, the error comparator turns the PMOS off for a minimum-offtime. The NMOS acts as an ideal rectifier that conducts when the PMOS is off. Using a NMOS switch instead of a diode allows for lower voltage drop across the switching device when it is on. The asynchronous switching combination between the PMOS and the NMOS allows the control loop to work in discontinuous mode for light load operations. In discontinuous mode, MIC33050 works in pulse frequency modulation (PFM) to regulate the output. As the output current increases, the switching frequency increases. This improves the efficiency of the MIC33050 during light load currents. As the load current increases, the MIC33050 goes into continuous conduction mode (CCM) at a constant frequency of 4MHz. The equation to calculate the load when the MIC33050 goes into continuous conduction mode may be approximated by the following formula: (V VOUT ) D ILOAD IN 2L f May 2012 11 M9999-050312-C Micrel, Inc. MIC33050 MIC33050 Typical Application Circuit (Fixed Output) Bill of Materials Item C1, C2 C3 R1 U1 Part Number C1608X5R0J475K C1608C0G1H561J CRCW0603100KFKEA MIC33050-xYHL Manufacturer Qty 4.7F Ceramic Capacitor, 6.3V, X5R, Size 0603 2 (1) 560pF Ceramic Capacitor, 50V, NPO, Size 0603 1 100k, Tolerance 1%, Size 0603 1 4MHz Internal Inductor PWM Buck Regulator with HyperLight Load(R) Mode 1 TDK TDK Description (1) (2) Vishay Micrel, Inc. (3) Notes: 1. TDK: www.tdk.com. 2. Vishay: www.vishay.com. 3. Micrel, Inc: www.micrel.com. May 2012 12 M9999-050312-C Micrel, Inc. MIC33050 MIC33050 Typical Application Circuit (Adjustable) Bill of Materials Item C1, C2 C3 Part Number C1608X5R0J475K C1608C0G1H121J Manufacturer Description Qty (1) 4.7F Ceramic Capacitor, 6.3V, X5R, Size 0603 2 (1) 120pF Ceramic Capacitor, 50V, NPO, Size 0603 1 TDK TDK (2) R1, R3 CRCW0603100KFKEA Vishay 100k, Tolerance 1%, Size 0603 2 R2 CRCW0603348KFKEA Vishay(2) 348k, Tolerance 1%, Size 0603 1 U1 MIC33050-AYHL Micrel, Inc. (3) 4MHz Internal Inductor PWM Buck Regulator with HyperLight Load(R) 1 Notes: 1. TDK: www.tdk.com 2. Vishay: www.vishay.com 3. Micrel, Inc: www.micrel.com May 2012 13 M9999-050312-C Micrel, Inc. MIC33050 PCB Layout Recommendations (Fixed) Top Layer Bottom Layer May 2012 14 M9999-050312-C Micrel, Inc. MIC33050 PCB Layout Recommendations (Adjustable) Top Layer Bottom Layer May 2012 15 M9999-050312-C Micrel, Inc. MIC33050 Package Information 12-Pin 3mm x 3mm MLF(R) (ML) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2007 Micrel, Incorporated. May 2012 16 M9999-050312-C Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Micrel: MIC33050-AYHL T5 MIC33050-AYHL TR MIC33050-GYHL TR MIC33050-SYHL TR MIC33050-CYHL TR MIC33050-4YHL TR MIC33050-AYHL-T5 MIC33050-4YHL-TR MIC33050-SYHL-TR MIC33050-AYHL-TR MIC33050GYHL-TR MIC33050-CYHL-TR