EV-ADE9000SHIELDZ - ANALOG DEVICES

EV-ADE9000SHIELDZ User Guide

UG-1170

One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com

ADE9000 Arduino-Compatible Energy and Power Quality Measurement Shield

Rev. 0 | Page 1 of 11

FEATURES

Arduino-compatible energy and power quality measurement

shield with ADE9000 multiphase energy and power quality

monitoring IC

3P4W, 3P3W, or 3-wire single phase measurements

Direct interface with current output current transformers

Up to 240 V rms nominal line neutral voltage measurement

Arduino software library

Calibration and example application sketches

ADDITIONAL EQUIPMENT NEEDED

Arduino Zero or equivalent

Current transformers

Voltage leads

USB microcable

DOCUMENTS NEEDED

ADE9000 data sheet

ADE9000 Technical Reference Manual

SOFTWARE NEEDED

Arduino IDE 1.8.1 or later

ADE9000 library files

GENERAL DESCRIPTION

The EV-ADE9000SHIELDZ is an Arduino shield compatible

with Arduino Zero. The shield can be directly interfaced with

current transformers and voltage leads. It enables quick

evaluation and prototyping of energy and power quality

measurement systems with the ADE9000. Arduino library and

application examples are provided to simplify implementation

of larger systems.

HAZARDOUS HIGH VOLTAGE

This equipment is connected to hazardous line voltages. Exercise

proper caution when connecting the sensors and voltage leads.

Ensure that the system is enclosed in a protective casing.

CONNECTION DIAGRAM

CURRENT INPUTS

PHASE A

ISOLATION

BARRIER ARDUINO S E CTI ONADE9000

PHASE B

PHASE C

NEUTRAL

VOLTAGE INPUTS

PHASE A

PHASE B

PHASE C

NEUTRAL

16137-001

Figure 1. EV-ADE9000SHIELDZ Connection Diagram

UG-1170 EV-ADE9000SHIELDZ User Guide

Rev. 0 | Page 2 of 11

TABLE OF CONTENTS

Features .............................................................................................. 1

Additional Equipment Needed ....................................................... 1

Documents Needed .......................................................................... 1

Software Needed ............................................................................... 1

General Description ......................................................................... 1

Hazardous High Voltage .................................................................. 1

Connection Diagram ....................................................................... 1

Revision History ............................................................................... 2

Module Hardware ............................................................................. 3

Powering the ADE9000 Shield ................................................... 3

Arduino Zero ................................................................................ 3

ESP8266 WiFi Module ................................................................. 3

Current Sensors .............................................................................3

Voltage Sensors ..............................................................................3

Libraries ..............................................................................................4

Installing the Libraries ..................................................................4

ADE9000 Arduino Library ..........................................................4

Line Voltage Connections ................................................................5

3-Phase, 4-Wire (3P4W) Wye .....................................................5

3-Phase, 3-Wire (3P3W) Delta ....................................................6

Evaluation Board Schematics ...........................................................7

Components .......................................................................................9

Bill of Materials ............................................................................... 10

REVISION HISTORY

1/2018—Revision 0: Initial Version

EV-ADE9000SHIELDZ User Guide UG-1170

Rev. 0 | Page 3 of 11

MODULE HARDWARE

POWERING THE ADE9000 SHIELD

The EV-ADE9000SHIELDZ requires 3.3 V and 5 V. It is

powered from the 3.3 V power pin and 5 V power pin from

Arduino or ESP8266.

ARDUINO ZERO

The ADE9000 shield has Arduino R3 headers directly

compatible with Arduino Uno and Arduino Zero. Using the

EV-ADE9000SHIELDZ with Arduino Zero or equivalent is

recommended. The Arduino pins used by the ADE9000 shield

are given in Table 1.

Table 1. Arduino GPIO Connections

Arduino Pin ADE9000 Signal Type

ICSP-SCK

SCLK

SPI

ICSP-MISO

MISO

SPI

ICSP-MOSI MOSI SPI

GPIO 8 CS (pulled up) SPI, output

GPIO 4 PM1 (pulled down) Output

GPIO 5 RESET (pulled up) Output

GPIO 2 IRQ0 Input (interrupt)

GPIO 3 IRQ1 Input (interrupt)

GPIO 6 CF4/DREADY/EVENT Input (interrupt)

GPIO 7 CF3/ZX Input (interrupt)

3.3 V Not applicable Power

5 V Not applicable Power

ESP8266 WIFI MODULE

The shield can also be used with the ESP8266 WiFi module. The

on-board header makes the shield compatible with ESP8266

ESP-12E NodeMCU. To use ESP8266, do the following:

• Solder 15-pin headers (SV1 and SV2)

• Populate 0 Ω resistors on R49, R51, R67, and R68 located

on the bottom of the board to establish an SPI connection.

• Optionally, supply external 5 V at J9 if the computer USB

does not provide enough current during debugging.

The ESP8266 pins used by the EV-ADE9000SHIELDZ are given

in Table 2.

Table 2. Arduino General-Purpose Input/Output (GPIO)

Connections

ESP8266 Pin ADE9000 Signal Type

D5 (GPIO 14) SCLK SPI

D6 (GPIO 12) MISO SPI

D7 (GPIO 13) MOSI SPI

D0 (GPIO 16) CS (pulled up) SPI, output

D8 (GPIO 15) PM1 (pulled down) Output

D1 (GPIO 5) IRQ0 Input

D2 (GPIO 4) IRQ1 Input

3.3 V

Not applicable

Power

5 V Not applicable Power

CURRENT SENSORS

The EV-ADE9000SHIELDZ is designed to work directly with

current output current transformers (C Ts). Connect the CT

leads to the SL1, SL2, SL3, and SL4 terminal blocks.

Current Output CTs

The EV-ADE9000SHIELDZ has on-board burden resistors in

differential configuration to allow direct connection with

current output CTs. With a typical 2500:1 CT, the maximum

recommended current is 86 A rms. Refer to the ADE9000

Technical Reference Manual to modify burden resistors for

different current ranges.

Voltage Output CTs

To use voltage output CTs, remove burden Resistors R1, R2, R3,

R4, R10, R11, R19, and R20. The maximum recommended CT

output voltage is ±0.353 V rms.

Rogowski Coils

To use Rogowski coils with EV-ADE9000SHIELDZ, do the

following:

• Remove burden Resistors R1, R2, R3, R4, R10, R11, R19,

and R20.

• Replace 0 Ω Resistors R5, R6, R14, R15, R21, R22, R23, and

R24 with 100 Ω resistors.

• Populate C15, C16, C17, C18, C21, C22, C26, and C28 with

22 nF ceramic C0G grade capacitors.

• In the ADE9000API.h file, do the following:

• Set the INTEN and ININTEN bits in the CONFIG0

• Set DICOEFF to 0xFFFFE000.

• If the Rogowski output signal is too low, increase the

PGA gain.

VOLTAGE SENSORS

The EV-ADE9000SHIELDZ has on-board resistor dividers to

attenuate the incoming input voltage. The attenuation factor is

801. Do not exceed the 240 V rms nominal line to neutral

voltage in the 3-phase, 4-wire (3P4W) wye configuration. In

3-wire delta configuration, when Phase B is used as the reference,

do not exceed 250 V rms line to line voltage. There are 4 mm

banana jacks on board to connect the voltage inputs. Use TPI

A079 or equivalent leads with alligator clips to connect the

voltage inputs.

UG-1170 EV-ADE9000SHIELDZ User Guide

Rev. 0 | Page 4 of 11

LIBRARIES

The EV-ADE9000SHIELDZ Arduino libraries provide basic

functions to access the ADE9000. The calibration sketch can be

used to calibrate the ADE9000 using an accurate source.

INSTALLING THE LIBRARIES

Download ADE9000ArduinoLibrary.zip.

Install the ADE9000 Arduino library, as shown in Figure 2.

16137-002

Figure 2. Installing Arduino Library. Original Content Hosted by Arduino,

Available at www.arduino.cc; Content from Arduino Republished Here Under

the Creative Commons Attribution-ShareAlike 3.0 Unported License, License

Available At www.arduino.cc/en/Main/CopyrightNotice; All Other Rights

Reserved by Analog Devices, Inc.

ADE9000 ARDUINO LIBRARY

ADE9000API.cpp

The ADE9000API.cpp file contains functions to communicate,

initialize, and read calculated parameters from the chip.

ADE9000API.h

The ADE9000API.h file contains register constants that are

written into the device by the SetupADE9000 function.

ADE9000CalibrationInputs.h

The ADE9000CalibrationInputs.h file contains the system

information used to calibrate the ADE9000. It is used by the

ADE9000 Calibration.ino sketch to compute the calibration

constants. The calibration constants are stored in the EEPROM.

ADE9000 Application Examples

The application examples demonstrate the use of functions in

ADE9000API.cpp and ADE9000API.h library files to obtain the

parameters calculated by the ADE9000. Connect Arduino Zero,

and compile and load the application examples to start

measuring energy and power quality.

EV-ADE9000SHIELDZ User Guide UG-1170

Rev. 0 | Page 5 of 11

LINE VOLTAGE CONNECTIONS

The EV-ADE9000SHIELDZ is connected to hazardous line

voltages. Exercise proper caution when connecting the sensors

and voltage leads. Ensure that the system is enclosed in a

protective casing.

3-PHASE, 4-WIRE (3P4W) WYE

The 3P4W wye connection is shown in Figure 3. Do not exceed

the nominal voltage of a 240 V rms line to neutral in wye

configuration.

CURRENT

INPUTS

PHASE A

PHASE B

PHASE C

NEUTRAL

VOLTAGE

INPUTS

PHASE A

PHASE B

PHASE C

NEUTRAL

240V rms

LINE

NEUTRAL

16137-003

Figure 3. 3P4W Wye Connection

UG-1170 EV-ADE9000SHIELDZ User Guide

Rev. 0 | Page 6 of 11

3-PHASE, 3-WIRE (3P3W) DELTA

The 3P3W delta connection is shown in Figure 4. Phase B is

used as the reference; therefore, the neutral channel on the

board is connected to Phase B. Do not exceed the 250 V rms

line to line voltage in the delta configuration. When using the delta

configuration, take the following actions in the ADE9000API.h file:

• Set VCONSEL to 001 so that VB = VA – VC.

• Set ICONSEL to 1 so that IB = −IA – IC.

CURRENT

INPUTS

PHASE A

PHASE C

VOLTAGE

INPUTS

PHASE A

PHASE B

PHASE C

NEUTRAL

400V rms

LINE TO LINE

16137-004

Figure 4. 3P3W Delta Connection

EV-ADE9000SHIELDZ User Guide UG-1170

Rev. 0 | Page 7 of 11

EVALUATION BOARD SCHEMATICS

PLACE DEC OUPL ING CAPS CL OSE TO IC PINS

VOLTAGE CHANNELSCURRENT CHANNELS

4 * 200k = 80 0k

0.287mV rms AT 230Vrms input

ALL ANT IALISING CAPS ARE C0 G NP0 GRADE

PHASE A

PHASE B

PHASE C

NEUTRAL

5.15.1

200k 200k 200k 200k

DNP

0.022u 0.022u

0.022u

18p18p

ADE9000ACPZ

10k

4.7u4.7u4.7u4.7u 0.1u0.1u0.1u0.1u

GND

10k

GND

25.161.0253.0

GND GND

200k 200k 200k 200k

0.022u

GND

200k 200k 200k 200k

0.022u

GND

0.022u

GND

0.022u

GND

5.15.1

DNP

0.022u

25.161.0253.0

GND

5.15.1

DNP

0.022u

25.161.0253.0

GND

5.15.1

DNP

0.022u

25.161.0253.0

GND

GND GND GND GND

GND

APT1608LSECK/J3-PRV

GND

GND GND

APT1608LZGCK

GND

+ 3V3_ADE + 3V3_ADE + 3V3_ADE

+ 3V3_ISO

+3V3_ADE

+ 3V3_ADE

+3V3_ADE

+3V3_ISO

GND

10k

+3V3_ADE

APT1608LSECK/J3-PRV

51p

R1R2

R12 R13 R9 R18

R21

R22

R29

R33

C15

C16

C23 C27

C29

C30

R35

R36

C37C38

VDD 27

IAN

8IAP

IBN

10 IBP

ICN

12 ICP

INN

14 INP

CF1 33

CF2 34

CF3/ ZX 35

CF4/ EVENT / DREADY 36

PM0 4

PM1 5

PULL_ HI GH 1

REF 16

DVDDOUT 3

AVDDOUT 25

SS 40

IRQ0 31

IRQ1 32

VAN

19 VAP

VBN

21 VBP

VCN

23 VCP

CLKI N 29

CLKOUT 30

MISO 38

MOSI 39

SCLK 37

RESET 6

NC1 17

NC2 18

GND

AGND

DGND

REFGND

EP(GND)

R43

C39 C40C41C42C43 C44C45C46C47

R47

R48

SL1

R27 R28 R30 R31

R32

C33

R34 R37 R38 R39

R40

C34

R41

C35

R42

C36

R3R4

C17

C18

C19

C20

SL2

R10R11

R14

R15

C21

C22

C24

C25

R16

R17

SL3

R19R20

R23

R24

C26

C28

C31

C32

R25

R26

SL4

LED1

R44

R45

R46

LED5

R50

R54

LED6

LED2

LED3

C52

C54

C55

MISO_ADE

MOSI_ADE

SCLK_ADE

SS_ADE

PM1_ADE

IRQ0_ADE IRQ0_ADE

IRQ1_ADE IRQ1_ADE

DREADY_ADE

ZX_ADE

CF2_I SO

CF1_I SO

IAN

IAP

IBN

IBP

ICN

ICP

INN

INP

VAP

VAN

VBP

VBN

VCP

VCN

DVDDOUT

AVDDOUT

REF

RESET_ADE

RECEPTABLE_RED

RECEPTABLE_BLACK

16137-005

Figure 5. EV-ADE9000SHIELDZ Schematic Sheet 1

UG-1170 EV-ADE9000SHIELDZ User Guide

Rev. 0 | Page 8 of 11

5V Signal from I sopower. 3. 3V Signal to Arduino

UNCONNECTED HEADER PINS ARE PASS-THROUGH HOT/ LIVE SIDE

SAFE SIDE

3.3V SIGNAL FROM ADE9000. 5V SIGNAL TO ISOPOWER

EEPROM SECTI ON

ARDUINO DI G I TAL PI NS D2- D7

RESET SECTI ON

HI GH VOLTAGE CAUTI ON

ESP8266 REDUCED CONNECTION SET

0.1u

GNDA

GND

0.1u

ADP122AUJZ-3.3-R7

10u 0.1u

ADUM4151BRIZ

SN74LV4T125PWR

GND

ADUM6404ARIZ

GND

+3V3_ADE

GND

10u 0.1u

GNDA GNDA

10u0.1u

GND

GNDA

0.1u

GNDA

GNDA 10k

+3V3_ADE

GNDA

10u 0.1u

GNDA

+5V_ARDUINO

GNDA

10u 0.1u

GNDA

+5V_ARDUINO

24LC32A/SN

GNDA

10k

DNP

GNDA

+5V_ARDUINO

0.1u 4.7u

GNDA

10u 0.1u

GND

4.7u0.1u

GND

3V3_ISO

3V3_ISO3V3_ISO

3V3_ISO

3V3_ISO 3V3_ISO

3V3_ISO

DNI

DNI DNP

DNP

10u0.1u

GNDA

10u 0.1u

GNDA

3V3_ISO 3V3_ISO

GNDA

+5V_ARDUINO

22u0.1u

GNDA

10k

GNDA

3GND 2

NC 4

VIN

VOUT

C11 C12

VDD1

1VDD2 20

VOA 14

VOB 13

VOC

VIA

VIB

VIC 12

MCLK

3SCLK 18

5MO

4SI 17

SO 16

*MSS

6*SSS 15

GND1_2

10 GND1

GND2_2 19

GND2 11

1OE_N 1

1A 2

2OE_N 4

2A 5

GND

83A 9

3OE_N 10

11 4A 12

4OE_N 13

VCC 14

1OE_N 1

1A 2

2OE_N 4

2A 5

GND

83A 9

3OE_N 10

11 4A 12

4OE_N 13

VCC 14

J10

VDD1

VDDL

VIA 14

VIB 13

VIC 12

VID 11

VISO 16

VSEL 10

VOA

VOB

VOC

VOD

GNDI SO_2 15

GNDI SO 9

GND_2

2GND

C48 C49 C50C51

C53

R53

C56

C57 C58C59 C60

VCC

GND

IC1

SCL

SDA 5

1A1

2A2

TP15TP16 TP17 TP18TP19 TP20

R52

R55

R56

R57

R58

R61

R62

TP5TP6 TP7 TP8TP9 TP10

C1 C7

C2 C4

C5C61

R59

R60

R63

R64

R65

R66

TP1 TP2 TP4TP3 TP21TP22

SV1

SV2

15 TP11 TP12 TP13 TP14

R49

R51

R67

R68

C9C10 C13 C14

TP23 TP24 TP25 TP26

TP27 TP28 TP29 TP30

C62C63

TP31TP32

VBUS

D-

D+

GND

SHLD1* 6

R69

5V_ADE

5V_ADE 5V_ADE

5V_ADE

RESET_ADE

MISO_ADE

MOSI_ADE

SCLK_ADE

SCLK_I SO

SCLK_ISO

SCLK_I SO

MOSI_ISO

MISO_ISO

MI SO_ISO

MISO_ISO

SS_I SO

PM1_I SO

PM1_ISO

ZX_ISO

DREADY_ISO

IRQ0_ISO

IRQ1_ISO

RESET_ISO

SCL_ARDUI NO

SDA_ARDUI NO

SS_ADE

PM1_ADE

ZX_ADE

DREADY_ADE

IRQ1_ADE

IRQ0_ADE

ZX_ARD

PM1_ARD

IRQ1_ARD

IRQ0_ARD

RESET_ARD

DREADY_ARD

Array

EEPROM

16137-006

Figure 6. EV-ADE9000SHIELDZ Schematic Sheet 2

EV-ADE9000SHIELDZ User Guide UG-1170

Rev. 0 | Page 9 of 11

COMPONENTS

Table 3 and Table 4 list required current transformers, voltage

leads, and clips. Equivalent components can also be used.

Table 3. Required Current Transformers

Manufacturer Part No.

TDK

CCT272440

VAC T60404-E4626-X002

Table 4. Required Voltage Leads and Clips

Manufacturer Part No.

Leads-TPI A079

Clips-TPI A058

Clips-Ponoma Electronics 6041B

UG-1170 EV-ADE9000SHIELDZ User Guide

Rev. 0 | Page 10 of 11

BILL OF MATERIALS

Qty Designator Description Manufacturer Part No.

16 R5, R6, R14, R15, R21 to

R24, R57, R59, R60, R62

to R66

Resistors, 0 Ω, 0.1 W, 0603 SMT,

RoHS

Yageo RC0603JR-070RL

8 R43, R48, R52 to R56,

R69

Resistors, 10 kΩ, 0.1 W, 0603

SMT, RoHS

Yageo RC0603JR-0710KL

14 R7, R8, R16, R17, R25,

R26, R29, R32, R33,

R35, R36, R40 to R42

Resistors, 1 kΩ, 0.1 W, 0603 SMT,

RoHS

Yageo RC0603FR-071KL

R9, R12, R13, R18, R27,

R28, R30, R31, R34,

R37 to R39

Resistors, 200 kΩ, 0.1 W, 2010

SMT, RoHS

Rohm Semiconductor

MCR50JZHF2003

5 R44 to R47, R50 Resistors, 3 kΩ, 0.1 W, 0603 SMT,

RoHS

Yageo RC0603FR-073KL

8 R1 to R4, R10, R11, R19,

R20

Resistors, 5.1 Ω, 0.1 W, 0805 SMT,

RoHS

TE Connectivity Passive Product CPF0805B5R1E1

12 C19, C20, C24, C25,

C29 to C36

Capacitors, 0.022 µF, 50 V, 5%,

0805 SMT, RoHS, C0G

TDK Corporation CGA4J2C0G1H223J125AA

19 C1, C3, C4, C6, C8, C10,

C12, C14, C44 to C47,

C49, C51, C53, C58,

C60, C61, C63

Capacitors, 0.1 µF, 25 V, 10%,

0603 SMT, RoHS, X7R

Murata Electronics North America GRM188R71E104KA01D

8 C2, C9, C11, C13, C48,

C50, C57, C59

Capacitors, 10 µF, 16 V, 10%, 0805

SMT, RoHS, X7R

Samsung Electro-Mechanics America, Inc. CL21B106KOQNNNE

2 C37, C38 Capacitors, 18 pF, 50 V, 1%, 0402

SMT, RoHS C0G

Murata Electronics North America GRM1555C1H180FA01D

2 C39, C56 Capacitors, 1 µF, 50 V, 10%, 0603

SMT, RoHS, X7R

Taiyo Yuden UMK107AB7105KA-T

1 C62 Capacitors, 22 µF, 25 V, 20%, 0805

SMT, RoHS, X5R

Murata Electronics North America GRM21BR61E226ME44L

3 C5, C7, C40 Capacitors, 4.7 µF, 25 V, 10%,

0805 SMT, RoHS, X5R

Murata Electronics North America GRM21BR61E475KA12L

3 C41 to C43 Capacitors, 4.7 µF, 25 V, 10%,

0603 SMT, RoHS, X5R

TDK Corporation C1608X5R1E475M080AC

3 C52, C54, C55 Capacitors, 51 pF, 50 V, 5%, 0402

SMT, RoHS, C0G

Samsung Electro-Mechanics America, Inc. CL05C510JB5NNNC

4 L1 to L4 Ferrite bead, 1500 Ω, 0805 SMT Murata Electronics North America BLM21BD152SN1D

1 J8 VOLTAGE_SOCKET_4MM_BLACK STAUBLI/Multi Contact 23.3200-21

3 J5 to J7 VOLTAGE_SOCKET_4MM_RED STAUBLI/Multi Contact 23.3200-22

1 IC1 IC, EEPROM, 32 KBIT, 400 KHz,

8-lead SOIC, 3.9 mm

Microchip Technology 24LC32AT-I/SN

4 LED1 to LED3, LED6 LED, 1.8 V, 2 mA, red, 0603 Kingbright APT1608LSECK/J3-PRV

1 LED5 LED, 2.65 V, 2 mA, green, 0603 Kingbright APT1608LZGCK

2 D1, D2 Diodes, Schottky, 30 V, 100 mA,

SOD323

Diodes Incorporated BAT54WS-7-F

1 Q8 Crystal, 24.576 MHz, 12 pF,

4-SMD

ECS Inc. ECS-245.7-12-33Q-JES-TR

8 Q1 to Q7, Q9 Diodes, dual series connection,

100 V, SOT-23-3

Fairchild/ON Semiconductor MMBD4148SE

1 J9 Connector, receptable, USB

MICRO AB, SMD

Hirose Electric Co Ltd ZX62-AB-5PA(31)

4 SL1 to SL4 Terminal blocks, 2 position, 5 mm

pitch, through hole

On Shore Technology Inc. ED350/2

1 U1 IC, ADE9000, poly phase

metering AFE, 40-lead LFCSP

Analog Devices, Inc. ADE9000ACPZ

1 U4 IC, ADP122, linear regulator, 3.3 V,

5-lead TSOT

Analog Devices, Inc. ADP122AUJZ-3.3-R7

EV-ADE9000SHIELDZ User Guide UG-1170

Rev. 0 | Page 11 of 11

Qty Designator Description Manufacturer Part No.

1 U5 IC, ADuM4151, SPI isolator,

17 MHz, 2/1 Data, 20-lead SOIC

Analog Devices, Inc. ADuM4151BRIZ-RL

1 U2 IC, ADuM6404, ISO power, 4

Channels, 16-lead SOIC

Analog Devices, Inc. ADuM6404ARIZ

1 S2 Switch, tactile SPST-NO,

surface- mount, 6 mm × 6 mm,

4 lead

C&K PTS645SM43SMTR92 LFS

2 U3, U6 ICs, SN74LV4T125, level translator,

noninverting, 14-TSSOP

Texas Instruments SN74LV4T125PWR

16 TP5 to TP10, TP15 to

TP22, TP31, TP32

Test points, 0.063", white Keystone Electronics 5007

1 J10 Connector, receptable, 3 × 2,

0.1" pitch

Sullins Connector Solutions PPTC032LFBN-RC

1 J4 Connector, receptable, 6 × 1,

0.1" pitch, long tail

Samtec Inc. 311-43-106-41-001000

2 J2, J3 Connectors, receptable, 8 × 1,

0.1" pitch, long tail

Samtec Inc. 311-43-108-41-001000

1 J1 Connector, receptable, 10 × 1,

0.1" pitch, long tail

Samtec Inc. 311-43-110-41-001000

16 TP1 to TP4, TP11 to

TP14, TP23 to TP30

Test pad

6 H1 to H6 Mount hole

6 R49, R51, R58, R61,

R67, R68

Do not install (DNI)

8 C15 to C18, C21, C22,

C26, C28

DNI

2 SV1, SV2 DNI Sullins Connector Solutions PPTC151LFBN-RC

ESD Caution

ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection

circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

Legal Terms and Conditions

By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set

forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have

read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc. (“ADI”),

with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary,

non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole

and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations:

Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term “Third Party”

includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the

Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or

transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the

Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any

modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation

Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees

to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF

ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING,

BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS

LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT

LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS

($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States federal laws and regulations

relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts (excluding conflict of law rules). Any

legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such

courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

registered trademarks are the property of their respective owners.

UG16137-0-1/18(0)