SN74LVC1T45 www.ti.com ..................................................................................................................................................... SCES515I - DECEMBER 2003 - REVISED MAY 2009 SINGLE-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS FEATURES 1 * Available in the Texas Instruments NanoFreeTM Package * Fully Configurable Dual-Rail Design Allows Each Port to Operate Over the Full 1.65-V to 5.5-V Power-Supply Range * VCC Isolation Feature - If Either VCC Input Is at GND, Both Ports Are in the High-Impedance State * DIR Input Circuit Referenced to VCCA * Low Power Consumption, 4-A Max ICC * 24-mA Output Drive at 3.3 V * Ioff Supports Partial-Power-Down Mode Operation * 2 DBV PACKAGE (TOP VIEW) VCCA 1 6 * * Max Data Rates - 420 Mbps (3.3-V to 5-V Translation) - 210 Mbps (Translate to 3.3 V) - 140 Mbps (Translate to 2.5 V) - 75 Mbps (Translate to 1.8 V) Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 - 2000-V Human-Body Model (A114-A) - 200-V Machine Model (A115-A) - 1000-V Charged-Device Model (C101) DCK PACKAGE (TOP VIEW) VCCB VCCA GND GND 2 5 DIR A 3 4 B A 1 2 3 6 5 4 DRL PACKAGE (TOP VIEW) VCCB DIR 1 VCCA 6 VCCB GND 2 5 DIR A 3 4 B YZP PACKAGE (BOTTOM VIEW) A GND VCCA C1 3 4 C2 B1 2 5 B2 A1 1 6 A2 B DIR VCCB B See mechanical drawings for dimensions. DESCRIPTION/ORDERING INFORMATION This single-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.65 V to 5.5 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional translation between any of the 1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes. The SN74LVC1T45 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input activate either the B-port outputs or the A-port outputs. The device transmits data from the A bus to the B bus when the B-port outputs are activated and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports always is active and must have a logic HIGH or LOW level applied to prevent excess ICC and ICCZ. The SN74LVC1T45 is designed so that the DIR input is powered by VCCA. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The VCC isolation feature ensures that if either VCC input is at GND, then both ports are in the high-impedance state. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. NanoFree is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2003-2009, Texas Instruments Incorporated SN74LVC1T45 SCES515I - DECEMBER 2003 - REVISED MAY 2009 ..................................................................................................................................................... www.ti.com NanoFreeTM package technology is a major breakthrough in IC packaging concepts, using the die as the package. ORDERING INFORMATION (1) PACKAGE (2) TA ORDERABLE PART NUMBER NanoFreeTM - WCSP (DSBGA) 0.23-mm Large Bump - YZP (Pb-free) SOT (SOT-23) - DBV -40C to 85C SOT (SC-70) - DCK SOT (SOT-533) - DRL (1) (2) (3) Reel of 3000 SN74LVC1T45YZPR Reel of 3000 SN74LVC1T45DBVR Reel of 250 SN74LVC1T45DBVT Reel of 3000 SN74LVC1T45DCKR Reel of 250 SN74LVC1T45DCKT Reel of 4000 SN74LVC1T45DRLR TOP-SIDE MARKING (3) _ _ _TA_ CT1_ TA_ For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. DBV/DCK/DRL: The actual top-side marking has one additional character that designates the wafer fab/assembly site. YZP: The actual top-side marking has three preceding characters to denote year, month, and sequence code, and one following character to designate the wafer fab/assembly site. Pin 1 identifier indicates solder-bump composition (1 = SnPb, * = Pb-free). FUNCTION TABLE (1) (1) INPUT DIR OPERATION L B data to A bus H A data to B bus Input circuits of the data I/Os always are active. LOGIC DIAGRAM (POSITIVE LOGIC) DIR A 5 3 4 VCCA 2 B VCCB Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 SN74LVC1T45 www.ti.com ..................................................................................................................................................... SCES515I - DECEMBER 2003 - REVISED MAY 2009 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX Supply voltage range -0.5 6.5 V VI Input voltage range (2) -0.5 6.5 V VO Voltage range applied to any output in the high-impedance or power-off state (2) -0.5 6.5 V A port -0.5 VCCA + 0.5 B port -0.5 VCCB + 0.5 VCCA VCCB UNIT VO Voltage range applied to any output in the high or low state (2) (3) IIK Input clamp current VI < 0 -50 mA IOK Output clamp current VO < 0 -50 mA IO Continuous output current 50 mA 100 mA Continuous current through VCC or GND JA Package thermal impedance (4) Tstg Storage temperature range DBV package 165 DCK package 259 DRL package 142 YZP package (1) (2) (3) (4) V C/W 123 -65 150 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. The value of VCC is provided in the recommended operating conditions table. The package thermal impedance is calculated in accordance with JESD 51-7. Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 3 SN74LVC1T45 SCES515I - DECEMBER 2003 - REVISED MAY 2009 ..................................................................................................................................................... www.ti.com Recommended Operating Conditions (1) (2) (3) VCCI VCCA VCCB VCCO Supply voltage 1.65 V to 1.95 V High-level input voltage VIH MAX 1.65 5.5 1.65 5.5 1.7 3 V to 3.6 V VCCI x 0.7 1.65 V to 1.95 V VIL Data inputs (4) VCCI x 0.35 2.3 V to 2.7 V 0.7 3 V to 3.6 V 0.8 4.5 V to 5.5 V High-level input voltage DIR (referenced to VCCA) (5) VCCA x 0.65 2.3 V to 2.7 V 1.7 3 V to 3.6 V V 2 4.5 V to 5.5 V VCCA x 0.7 1.65 V to 1.95 V DIR (referenced to VCCA) (5) V VCCI x 0.3 1.65 V to 1.95 V VIH V V 2 4.5 V to 5.5 V Low-level input voltage UNIT VCCI x 0.65 2.3 V to 2.7 V Data inputs (4) MIN VCCA x 0.35 2.3 V to 2.7 V 0.7 3 V to 3.6 V 0.8 VIL Low-level input voltage VI Input voltage 0 5.5 V VO Output voltage 0 VCCO V 4.5 V to 5.5 V VCCA x 0.3 1.65 V to 1.95 V IOH High-level output current IOL Low-level output current t/v Input transition rise or fall rate Data inputs Control inputs TA (1) (2) (3) (4) (5) 4 V -4 2.3 V to 2.7 V -8 3 V to 3.6 V -24 4.5 V to 5.5 V -32 1.65 V to 1.95 V 4 2.3 V to 2.7 V 8 3 V to 3.6 V 24 4.5 V to 5.5 V 32 1.65 V to 1.95 V 20 2.3 V to 2.7 V 20 3 V to 3.6 V 10 4.5 V to 5.5 V 5 1.65 V to 5.5 V 5 Operating free-air temperature -40 85 mA mA ns/V C VCCI is the VCC associated with the input port. VCCO is the VCC associated with the output port. All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. For VCCI values not specified in the data sheet, VIH min = VCCI x 0.7 V, VIL max = VCCI x 0.3 V. For VCCI values not specified in the data sheet, VIH min = VCCA x 0.7 V, VIL max = VCCA x 0.3 V. Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 SN74LVC1T45 www.ti.com ..................................................................................................................................................... SCES515I - DECEMBER 2003 - REVISED MAY 2009 Electrical Characteristics (1) (2) over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = -100 A IOH = -8 mA 1.65 V to 4.5 V 1.65 V to 4.5 V 1.65 V 1.65 V 1.2 2.3 V 2.3 V 1.9 VI = VIH DIR A port Ioff B port A or B port IOZ ICCA A port ICCA MAX V 3V 2.4 3.8 IOL = 100 A 1.65 V to 4.5 V 1.65 V to 4.5 V 0.1 1.65 V 1.65 V 0.45 VI = VIL 2.3 V 2.3 V 0.3 IOL = 24 mA 3V 3V 0.55 IOL = 32 mA 4.5 V 4.5 V 0.55 1.65 V to 5.5 V 1.65 V to 5.5 V 1 2 0V 0 to 5.5 V 1 2 0 to 5.5 V 0V 1 2 1.65 V to 5.5 V 1.65 V to 5.5 V 1 2 1.65 V to 5.5 V 1.65 V to 5.5 V 3 5.5 V 0V 2 -2 VI = VCCA or GND VI or VO = 0 to 5.5 V VO = VCCO or GND VI = VCCI or GND, IO = 0 0V 5.5 V 1.65 V to 5.5 V 1.65 V to 5.5 V 3 5.5 V 0V -2 0V 5.5 V 2 1.65 V to 5.5 V 1.65 V to 5.5 V 4 3 V to 5.5 V 3 V to 5.5 V A port at VCCA - 0.6 V, DIR at VCCA, B port = open DIR at VCCA - 0.6 V, B port = open, A port at VCCA or GND ICCB B port B port at VCCB - 0.6 V, DIR at GND, A port = open Ci DIR Cio A or B port UNIT VCCO - 0.1 4.5 V DIR (1) (2) MIN 3V VI = VCCI or GND, IO = 0 ICCA + ICCB (see Table 1) MAX 4.5 V VI = VCCI or GND, IO = 0 ICCB TYP IOH = -32 mA IOL = 8 mA II MIN IOH = -24 mA IOL = 4 mA VOL -40C to 85C VCCB IOH = -4 mA VOH TA = 25C VCCA V A A A A A A 50 A 50 50 A 3 V to 5.5 V 3 V to 5.5 V VI = VCCA or GND 3.3 V 3.3 V 2.5 pF VO = VCCA/B or GND 3.3 V 3.3 V 6 pF VCCO is the VCC associated with the output port. VCCI is the VCC associated with the input port. Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 5 SN74LVC1T45 SCES515I - DECEMBER 2003 - REVISED MAY 2009 ..................................................................................................................................................... www.ti.com Switching Characteristics over recommended operating free-air temperature range, VCCA = 1.8 V 0.15 V (see Figure 1) PARAMETER tPLH tPHL tPLH tPHL tPHZ tPLZ tPHZ tPLZ tPZH (1) tPZL (1) tPZH (1) tPZL (1) (1) FROM (INPUT) TO (OUTPUT) A B B A DIR A DIR B DIR A DIR B VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V VCCB = 5 V 0.5 V UNIT MIN MAX MIN MAX MIN MAX MIN MAX 3 17.7 2.2 10.3 1.7 8.3 1.4 7.2 2.8 14.3 2.2 8.5 1.8 7.1 1.7 7 3 17.7 2.3 16 2.1 15.5 1.9 15.1 2.8 14.3 2.1 12.9 2 12.6 1.8 12.2 5.2 19.4 4.8 18.5 4.7 18.4 5.1 17.1 2.3 10.5 2.1 10.5 2.4 10.7 3.1 10.9 7.4 21.9 4.9 11.5 4.6 10.3 2.8 8.2 4.2 16 3.7 9.2 3.3 8.4 2.4 6.4 33.7 25.2 23.9 21.5 36.2 24.4 22.9 20.4 28.2 20.8 19 18.1 33.7 27 25.5 24.1 ns ns ns ns ns ns The enable time is a calculated value, derived using the formula shown in the enable times section. Switching Characteristics over recommended operating free-air temperature range, VCCA = 2.5 V 0.2 V (see Figure 1) PARAMETER tPLH tPHL tPLH tPHL tPHZ tPLZ tPHZ tPLZ tPZH (1) tPZL (1) tPZH (1) tPZL (1) 6 (1) FROM (INPUT) TO (OUTPUT) A B B A DIR A DIR B DIR A DIR B VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V VCCB = 5 V 0.5 V UNIT MIN MAX MIN MAX MIN MAX MIN MAX 2.3 16 1.5 8.5 1.3 6.4 1.1 5.1 2.1 12.9 1.4 7.5 1.3 5.4 0.9 4.6 2.2 10.3 1.5 8.5 1.4 8 1 7.5 2.2 8.5 1.4 7.5 1.3 7 0.9 6.2 3 8.1 3.1 8.1 2.8 8.1 3.2 8.1 1.3 5.9 1.3 5.9 1.3 5.9 1 5.8 6.5 23.7 4.1 11.4 3.9 10.2 2.4 7.1 3.9 18.9 3.2 9.6 2.8 8.4 1.8 5.3 29.2 18.1 16.4 12.8 32.2 18.9 17.2 13.3 21.9 14.4 12.3 10.9 21 15.6 13.5 12.7 ns ns ns ns ns ns The enable time is a calculated value, derived using the formula shown in the enable times section. Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 SN74LVC1T45 www.ti.com ..................................................................................................................................................... SCES515I - DECEMBER 2003 - REVISED MAY 2009 Switching Characteristics over recommended operating free-air temperature range, VCCA = 3.3 V 0.3 V (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) A B B A DIR A DIR B DIR A DIR B tPLH tPHL tPLH tPHL tPHZ tPLZ tPHZ tPLZ tPZH (1) tPZL (1) tPZH (1) tPZL (1) (1) VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V VCCB = 5 V 0.5 V UNIT MIN MAX MIN MAX MIN MAX MIN MAX 2.1 15.5 1.4 8 0.7 5.8 0.7 4.4 2 12.6 1.3 7 0.8 5 0.7 4 1.7 8.3 1.3 6.4 0.7 5.8 0.6 5.4 1.8 7.1 1.3 5.4 0.8 5 0.7 4.5 2.9 7.3 3 7.3 2.8 7.3 3.4 7.3 1.8 5.6 1.6 5.6 2.2 5.7 2.2 5.7 5.4 20.5 3.9 10.1 2.9 8.8 2.4 6.8 3.3 14.5 2.9 7.8 2.4 7.1 1.7 4.9 22.8 14.2 12.9 10.3 27.6 15.5 13.8 11.3 21.1 13.6 11.5 10.1 19.9 14.3 12.3 11.3 ns ns ns ns ns ns The enable time is a calculated value, derived using the formula shown in the enable times section. Switching Characteristics over recommended operating free-air temperature range, VCCA = 5 V 0.5 V (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) A B B A DIR A DIR B DIR A DIR B tPLH tPHL tPLH tPHL tPHZ tPLZ tPHZ tPLZ tPZH (1) tPZL (1) tPZH (1) tPZL (1) (1) VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V VCCB = 5 V 0.5 V UNIT MIN MAX MIN MAX MIN MAX MIN MAX 1.9 15.1 1 7.5 0.6 5.4 0.5 3.9 1.8 12.2 0.9 6.2 0.7 4.5 0.5 3.5 1.4 7.2 1 5.1 0.7 4.4 0.5 3.9 1.7 7 0.9 4.6 0.7 4 0.5 3.5 2.1 5.4 2.2 5.4 2.2 5.5 2.2 5.4 0.9 3.8 1 3.8 1 3.7 0.9 3.7 4.8 20.2 2.5 9.8 1 8.5 2.5 6.5 4.2 14.8 2.5 7.4 2.5 7 1.6 4.5 22 12.5 11.4 8.4 27.2 14.4 12.5 10 18.9 11.3 9.1 7.6 17.6 11.6 10 8.6 ns ns ns ns ns ns The enable time is a calculated value, derived using the formula shown in the enable times section. Operating Characteristics TA = 25C PARAMETER CpdA (1) CpdB (1) (1) A-port input, B-port output B-port input, A-port output A-port input, B-port output B-port input, A-port output TEST CONDITIONS CL = 0 pF, f = 10 MHz, tr = tf = 1 ns CL = 0 pF, f = 10 MHz, tr = tf = 1 ns VCCA = VCCB = 1.8 V VCCA = VCCB = 2.5 V VCCA = VCCB = 3.3 V VCCA = VCCB = 5 V TYP TYP TYP TYP 3 4 4 4 18 19 20 21 18 19 20 21 3 4 4 4 UNIT pF pF Power dissipation capacitance per transceiver Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 7 SN74LVC1T45 SCES515I - DECEMBER 2003 - REVISED MAY 2009 ..................................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE TA = 25C, VCCA = 1.8 V 10 10 9 9 8 VCCB = 1.8 V 8 7 7 6 6 t PLH- ns t PHL - ns VCCB = 1.8 V VCCB = 2.5 V 5 4 VCCB = 2.5 V 5 VCCB = 3.3 V 4 VCCB = 5 V VCCB = 3.3 V 3 3 VCCB = 5 V 2 2 1 1 0 0 5 10 20 15 25 30 0 35 0 10 5 CL - pF 15 20 25 30 35 25 30 35 CL - pF TYPICAL PROPAGATION DELAY (B to A) vs LOAD CAPACITANCE TA = 25C, VCCA = 1.8 V 10 10 9 9 VCCB = 1.8 V 8 VCCB = 2.5 V 8 7 7 6 6 t PLH - ns t PHL - ns VCCB = 1.8 V 5 VCCB = 2.5 V 4 VCCB = 3.3 V VCCB = 3.3 V VCCB = 5 V 5 4 VCCB = 5 V 3 3 2 2 1 1 0 0 5 10 15 20 25 30 35 0 0 5 CL - pF 8 10 15 20 CL - pF Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 SN74LVC1T45 www.ti.com ..................................................................................................................................................... SCES515I - DECEMBER 2003 - REVISED MAY 2009 TYPICAL CHARACTERISTICS (continued) TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE TA = 25C, VCCA = 2.5 V 10 10 9 9 8 8 7 VCCB = 1.8 V 6 t PLH - ns t PHL - ns 7 VCCB = 1.8 V 5 6 5 VCCB = 2.5 V 4 4 VCCB = 3.3 V 3 3 VCCB = 5 V VCCB = 2.5 V VCCB = 3.3 V 2 2 VCCB = 5 V 1 1 0 0 0 10 5 15 20 25 30 0 35 10 5 15 CL - pF 20 25 30 35 CL - pF 10 10 9 9 8 8 7 7 t PLH - ns t PHL - ns TYPICAL PROPAGATION DELAY (B to A) vs LOAD CAPACITANCE TA = 25C, VCCA = 2.5 V 6 VCCB = 1.8 V 5 6 5 4 4 3 3 VCCB = 2.5 V VCCB = 3.3 V VCCB = 5 V 2 VCCB = 2.5 V VCCB = 3.3 V VCCB = 5 V 2 1 1 0 VCCB = 1.8 V 0 0 5 10 15 20 CL - pF 25 30 35 0 5 10 15 20 25 30 35 CL - pF Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 9 SN74LVC1T45 SCES515I - DECEMBER 2003 - REVISED MAY 2009 ..................................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS (continued) TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE TA = 25C, VCCA = 3.3 V 10 10 9 9 8 8 VCCB = 1.8 V 7 7 VCCB = 1.8 V 6 t PLH - ns t PHL - ns 6 5 4 VCCB = 2.5 V 5 VCCB = 2.5 V 4 VCCB = 3.3 V 3 3 2 2 VCCB = 5 V VCCB = 3.3 V 0 1 VCCB = 5 V 1 0 10 5 15 20 25 30 0 0 35 5 10 15 20 25 30 35 25 30 35 CL - pF CL - pF 10 10 9 9 8 8 7 7 6 6 t PLH - ns t PHL - ns TYPICAL PROPAGATION DELAY (B to A) vs LOAD CAPACITANCE TA = 25C, VCCA = 3.3 V 5 VCCB = 1.8 V 4 5 VCCB = 1.8 V 4 VCCB = 2.5 V VCCB = 2.5 V 3 3 2 VCCB = 5 V VCCB = 5 V 1 VCCB = 3.3 V 2 VCCB = 3.3 V 1 0 0 0 5 10 15 20 25 30 35 0 5 15 20 CL - pF CL - pF 10 10 Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 SN74LVC1T45 www.ti.com ..................................................................................................................................................... SCES515I - DECEMBER 2003 - REVISED MAY 2009 TYPICAL CHARACTERISTICS (continued) TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE TA = 25C, VCCA = 5 V 10 10 9 9 8 8 7 7 VCCB = 1.8 V VCCB = 1.8 V t PLH - ns t PHL - ns 6 5 4 VCCB = 2.5 V 3 6 5 VCCB = 2.5 V 4 VCCB = 3.3 V 3 2 2 VCCB = 5 V VCCB = 3.3 V 1 VCCB = 5 V 1 0 0 0 5 10 15 20 25 30 0 35 5 10 15 20 25 30 35 25 30 35 CL - pF CL - pF 10 10 9 9 8 8 7 7 6 6 t PLH - ns t PHL- ns TYPICAL PROPAGATION DELAY (B to A) vs LOAD CAPACITANCE TA = 25C, VCCA = 5 V 5 4 VCCB = 1.8 V 3 VCCB = 2.5 V 5 VCCB = 1.8 V 4 VCCB = 2.5 V 3 2 2 VCCB = 3.3 V VCCB = 5 V VCCB = 3.3 V 1 0 1 VCCB = 5 V 0 5 0 10 15 20 25 30 35 0 5 CL - pF 10 15 20 CL - pF Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 11 SN74LVC1T45 SCES515I - DECEMBER 2003 - REVISED MAY 2009 ..................................................................................................................................................... www.ti.com PARAMETER MEASUREMENT INFORMATION 2 x VCCO S1 RL From Output Under Test Open GND CL (see Note A) TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 x VCCO GND RL tw LOAD CIRCUIT VCCI VCCI/2 Input VCCO CL RL VTP 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 5 V 0.5 V 15 pF 15 pF 15 pF 15 pF 2 k 2 k 2 k 2 k 0.15 V 0.15 V 0.3 V 0.3 V VCCI/2 0V VOLTAGE WAVEFORMS PULSE DURATION VCCA Output Control (low-level enabling) VCCA/2 VCCA/2 0V tPZL VCCI Input VCCI/2 VCCI/2 0V tPLH Output tPHL VOH VCCO/2 VOL VCCO/2 tPLZ VCCO Output Waveform 1 S1 at 2 x VCCO (see Note B) VCCO/2 VOL + VTP VOL tPZH Output Waveform 2 S1 at GND (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES tPHZ VCCO/2 VOH - VTP VOH 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR v10 MHz, ZO = 50 , dv/dt 1 V/ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. VCCI is the VCC associated with the input port. I. VCCO is the VCC associated with the output port. J. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 12 Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 SN74LVC1T45 www.ti.com ..................................................................................................................................................... SCES515I - DECEMBER 2003 - REVISED MAY 2009 APPLICATION INFORMATION Figure 2 shows an example of the SN74LVC1T45 being used in a unidirectional logic level-shifting application. VCC1 VCC1 VCC2 1 6 2 5 3 4 SYSTEM-1 VCC2 SYSTEM-2 PIN NAME FUNCTION 1 VCCA VCC1 SYSTEM-1 supply voltage (1.65 V to 5.5 V) DESCRIPTION 2 GND GND Device GND 3 A OUT Output level depends on VCC1 voltage. 4 B IN 5 DIR DIR GND (low level) determines B-port to A-port direction. 6 VCCB VCC2 SYSTEM-2 supply voltage (1.65 V to 5.5 V) Input threshold value depends on VCC2 voltage. Figure 2. Unidirectional Logic Level-Shifting Application Figure 3 shows the SN74LVC1T45 being used in a bidirectional logic level-shifting application. Since the SN74LVC1T45 does not have an output-enable (OE) pin, the system designer should take precautions to avoid bus contention between SYSTEM-1 and SYSTEM-2 when changing directions. VCC1 VCC1 VCC2 VCC2 I/O-1 Pullup/Down or Bus Hold(1) Pullup/Down or Bus Hold(1) 1 6 2 5 3 4 I/O-2 DIR CTRL SYSTEM-1 SYSTEM-2 Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 13 SN74LVC1T45 SCES515I - DECEMBER 2003 - REVISED MAY 2009 ..................................................................................................................................................... www.ti.com The following table shows data transmission from SYSTEM-1 to SYSTEM-2 and then from SYSTEM-2 to SYSTEM-1. STATE DIR CTRL I/O-1 I/O-2 1 H Out In 2 H Hi-Z Hi-Z SYSTEM-2 is getting ready to send data to SYSTEM-1. I/O-1 and I/O-2 are disabled. The bus-line state depends on pullup or pulldown. (1) 3 L Hi-Z Hi-Z DIR bit is flipped. I/O-1 and I/O-2 still are disabled. The bus-line state depends on pullup or pulldown. (1) 4 L Out In (1) DESCRIPTION SYSTEM-1 data to SYSTEM-2 SYSTEM-2 data to SYSTEM-1 SYSTEM-1 and SYSTEM-2 must use the same conditions, i.e., both pullup or both pulldown. Figure 3. Bidirectional Logic Level-Shifting Application Enable Times Calculate the enable times for the SN74LVC1T45 using the following formulas: * tPZH (DIR to A) = tPLZ (DIR to B) + tPLH (B to A) * tPZL (DIR to A) = tPHZ (DIR to B) + tPHL (B to A) * tPZH (DIR to B) = tPLZ (DIR to A) + tPLH (A to B) * tPZL (DIR to B) = tPHZ (DIR to A) + tPHL (A to B) In a bidirectional application, these enable times provide the maximum delay from the time the DIR bit is switched until an output is expected. For example, if the SN74LVC1T45 initially is transmitting from A to B, then the DIR bit is switched; the B port of the device must be disabled before presenting it with an input. After the B port has been disabled, an input signal applied to it appears on the corresponding A port after the specified propagation delay. 14 Submit Documentation Feedback Copyright (c) 2003-2009, Texas Instruments Incorporated Product Folder Link(s): SN74LVC1T45 PACKAGE OPTION ADDENDUM www.ti.com 3-Mar-2012 PACKAGING INFORMATION Orderable Device (1) Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DBVRE4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DBVTE4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DCKR ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DCKRE4 ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DCKRG4 ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DCKT ACTIVE SC70 DCK 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DCKTE4 ACTIVE SC70 DCK 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DCKTG4 ACTIVE SC70 DCK 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DPKR ACTIVE USON DPK 6 5000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DRLR ACTIVE SOT DRL 6 4000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45DRLRG4 ACTIVE SOT DRL 6 4000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74LVC1T45YZPR ACTIVE DSBGA YZP 6 3000 Green (RoHS & no Sb/Br) The marketing status values are defined as follows: Addendum-Page 1 Samples (Requires Login) SN74LVC1T45DBVR SNAGCU (3) Level-1-260C-UNLIM PACKAGE OPTION ADDENDUM www.ti.com 3-Mar-2012 ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN74LVC1T45 : * Automotive: SN74LVC1T45-Q1 * Enhanced Product: SN74LVC1T45-EP NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 26-May-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) SN74LVC1T45DBVR SOT-23 DBV 6 3000 180.0 8.4 SN74LVC1T45DBVR SOT-23 DBV 6 3000 178.0 SN74LVC1T45DBVT SOT-23 DBV 6 250 180.0 SN74LVC1T45DCKR SC70 DCK 6 3000 SN74LVC1T45DCKR SC70 DCK 6 SN74LVC1T45DCKT SC70 DCK SN74LVC1T45DCKT SC70 DCK SN74LVC1T45DCKT SC70 SN74LVC1T45DPKR SN74LVC1T45DRLR 3.23 3.17 1.37 4.0 8.0 Q3 9.0 3.23 3.17 1.37 4.0 8.0 Q3 8.4 3.23 3.17 1.37 4.0 8.0 Q3 178.0 9.0 2.4 2.5 1.2 4.0 8.0 Q3 3000 180.0 8.4 2.25 2.4 1.22 4.0 8.0 Q3 6 250 180.0 8.4 2.25 2.4 1.22 4.0 8.0 Q3 6 250 178.0 9.2 2.4 2.4 1.22 4.0 8.0 Q3 DCK 6 250 178.0 9.0 2.4 2.5 1.2 4.0 8.0 Q3 USON DPK 6 5000 180.0 9.5 1.75 1.75 0.7 4.0 8.0 Q2 SOT DRL 6 4000 180.0 9.5 1.78 1.78 0.69 4.0 8.0 Q3 SN74LVC1T45DRLR SOT DRL 6 4000 180.0 8.4 1.98 1.78 0.69 4.0 8.0 Q3 SN74LVC1T45YZPR DSBGA YZP 6 3000 180.0 8.4 1.02 1.52 0.63 4.0 8.0 Q1 SN74LVC1T45YZPR DSBGA YZP 6 3000 178.0 9.2 1.02 1.52 0.63 4.0 8.0 Q1 Pack Materials-Page 1 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 26-May-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74LVC1T45DBVR SOT-23 DBV 6 3000 202.0 201.0 28.0 SN74LVC1T45DBVR SOT-23 DBV 6 3000 180.0 180.0 18.0 SN74LVC1T45DBVT SOT-23 DBV 6 250 202.0 201.0 28.0 SN74LVC1T45DCKR SC70 DCK 6 3000 180.0 180.0 18.0 SN74LVC1T45DCKR SC70 DCK 6 3000 202.0 201.0 28.0 SN74LVC1T45DCKT SC70 DCK 6 250 202.0 201.0 28.0 SN74LVC1T45DCKT SC70 DCK 6 250 180.0 180.0 18.0 SN74LVC1T45DCKT SC70 DCK 6 250 180.0 180.0 18.0 SN74LVC1T45DPKR USON DPK 6 5000 180.0 180.0 30.0 SN74LVC1T45DRLR SOT DRL 6 4000 180.0 180.0 30.0 SN74LVC1T45DRLR SOT DRL 6 4000 202.0 201.0 28.0 SN74LVC1T45YZPR DSBGA YZP 6 3000 220.0 220.0 34.0 SN74LVC1T45YZPR DSBGA YZP 6 3000 220.0 220.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated