PCM1801 SBAS131C - OCTOBER 2000 - REVISED JULY 2007 SINGLE-ENDED ANALOG-INPUT 16-BIT STEREO ANALOG-TO-DIGITAL CONVERTER FEATURES APPLICATIONS * * * * * * * * * * * * * * Dual 16-Bit Monolithic ADC Single-Ended Voltage Input Antialiasing Filter Included 64x Oversampling Decimation Filter: Pass-Band Ripple: 0.05 dB Stop-Band Attenuation: -65 dB Analog Performance: THD+N: -88 dB (typical) SNR: 93 dB (typical) Dynamic Range: 93 dB (typical) Internal High-Pass Filter PCM Audio Interface: Left-Justified, I2S Sampling Rate: 4 kHz to 48 kHz System Clock: 256 fS, 384 fS, or 512 fS Single 5-V Power Supply Small SO-14 Package DVD Recorders DVD Receivers AV Amplifier Receivers Electric Musical Instruments DESCRIPTION The PCM1801 is a low-cost, single-chip stereo analog-to-digital converter (ADC) with single-ended analog voltage inputs. The PCM1801 uses a delta-sigma modulator with 64 times oversampling, a digital decimation filter, and a serial interface that supports slave mode operation and two data formats. The PCM1801 is suitable for a wide variety of cost-sensitive consumer applications where good performance is required. PCM1801 (+) VINL Single-End/ Differential Converter (-) 5th Order Delta-Sigma Modulator x1/64 Decimation and High-Pass Filter VREF1 Reference VREF2 (-) VINR Single-End/ Differential Converter BCK (+) 5th Order Delta-Sigma Modulator Serial Data Interface LRCK DOUT Format Control FMT BYPAS Clock/Timing Control SCKI Power Supply VCC AGND DGND VDD B0004-02 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. System Two, Audio Precision are trademarks of Audio Precision, Inc. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2000-2007, Texas Instruments Incorporated PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE TYPE PACKAGE CODE PACKAGE MARKING PCM1801U 14-pin SOIC D PCM1801U ORDERING NUMBER TRANSPORT MEDIA QUANTITY PCM1801U Rails 56 PCM1801U/2K Tape and reel 2000 ABSOLUTE MAXIMUM RATINGS Supply voltage: VDD, VCC -0.3 V to 6.5 V 0.1 V Supply voltage differences: VDD, VCC 0.1 V GND voltage differences: AGND, DGND Digital input voltage -0.3 V to (VDD + 0.3 V), < 6.5 V Analog input voltage -0.3 V to (VCC + 0.3 V), < 6.5 V Input current (any pin except supplies) 10 mA Power dissipation 300 mW Operating temperature range -25C to 85C Storage temperature -55C to 125C Lead temperature, soldering 260C, 5 s Package temperature (IR reflow, peak) 235C RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range MIN NOM MAX Analog supply voltage, VCC 4.5 5 5.5 Digital supply voltage, VDD 4.5 5 5.5 Analog input voltage, full-scale (-0 dB) 2.828 Digital input logic family Digital input clock frequency V V Vp-p TTL System clock Sampling clock 8.192 24.576 MHz 32 48 kHz Digital output load capacitance 10 Operating free-air temperature, TA 2 UNIT -25 Submit Documentation Feedback pF 85 C PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 PIN CONFIGURATION PCM1801 (TOP VIEW) VINL 1 14 VREF1 VINR 2 13 VREF2 DGND 3 12 AGND VDD 4 11 VCC SCKI 5 10 FMT BCK 6 9 BYPAS LRCK 7 8 DOUT P0005-01 Table 1. PIN ASSIGNMENTS NAME PIN I/O AGND 12 - Analog ground DESCRIPTION BCK 6 I Bit clock input BYPAS 9 I HPF bypass control (1) DGND 3 - Digital ground DOUT 8 O Audio data output FMT 10 I Audio data format(1) L: HPF enabled H: HPF disabled L: MSB-first, left-justified H: MSB-first, I2S (1) LRCK 7 I Sampling clock input SCKI 5 I System clock input; 256 fS, 384 fS, or 512 fS VCC 11 - Analog power supply VDD 4 - Digital power supply VINL 1 I Analog input, Lch VINR 2 I Analog input, Rch VREF1 14 - Reference 1 decoupling capacitor VREF2 13 - Reference 2 decoupling capacitor With 100-k typical pulldown resistor Submit Documentation Feedback 3 PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 ELECTRICAL CHARACTERISTICS All specifications at TA = 25C, VDD = VCC = 5 V, fS = 44.1 kHz, 16-bit data, and SYSCLK = 384 fS, unless otherwise noted. PARAMETER TEST CONDITIONS PCM1801U MIN RESOLUTION TYP MAX 16 UNITS Bits DIGITAL INPUT/OUTPUT VIH (1) VIL (1) IIN (2) IIN (3) VOH (4) VOL fS (4) 2 Input logic level 0.8 10 Input logic current Output logic level 100 IOH = -1.6 mA 4.5 IOL = 3.2 mA Sampling frequency 0.5 VDC A VDC 4 44.1 48 256 fS 1.024 11.2896 12.288 384 fS 1.536 16.9344 18.432 512 fS 2.048 22.5792 24.576 1 2.5 Gain error 2 5 Gain drift 20 ppm of FSR/C System clock frequency kHz MHz DC ACCURACY Gain mismatch, channel-to-channel % of FSR % of FSR Bipolar zero error High-pass filter bypassed 2 % of FSR Bipolar zero drift High-pass filter bypassed 20 ppm of FSR/C FS (-0.5 dB) -88 -60 dB -90 DYNAMIC PERFORMANCE (5) THD+N -80 dB Dynamic range A-weighted 90 93 dB Signal-to-noise ratio A-weighted 90 93 dB 87 90 dB 2.828 Vp-p 2.1 V Channel separation ANALOG INPUT Input range FS (VIN = 0 dB) Center voltage Input impedance Antialiasing filter frequency response -3 dB 30 k 150 kHz DIGITAL FILTER PERFORMANCE Pass band 0.454 fS Stop band 0.583 fS Hz 0.05 Pass-band ripple Stop-band attenuation -65 Delay time (latency) High-pass frequency response (1) (2) (3) (4) (5) 4 -3 dB Hz dB dB 17.4/fS s 0.019 fS mHz Pins 5, 6, 7, 9, and 10 (SCKI, BCK, LRCK, BYPAS, and FMT) Pins 5, 6, 7 (SCKI, BCK, LRCK) Schmitt-trigger input Pins 9, 10 (BYPAS, FMT) Schmitt-trigger input with 100-k typical pulldown resistor Pin 8 (DOUT) fIN = 1 kHz, using the System TwoTM audio measurement system by Audio PrecisionTM in rms mode with 20-kHz LPF and 400-Hz HPF in the performance calculation. Submit Documentation Feedback PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 ELECTRICAL CHARACTERISTICS (continued) All specifications at TA = 25C, VDD = VCC = 5 V, fS = 44.1 kHz, 16-bit data, and SYSCLK = 384 fS, unless otherwise noted. PARAMETER PCM1801U TEST CONDITIONS MIN TYP MAX 4.5 5 5.5 4.5 5 5.5 UNITS POWER SUPPLY REQUIREMENTS VCC Voltage range VDD VDC Supply current (6) VCC = VDD = 5 V 18 24 mA Power dissipation VCC = VDD = 5 V 90 120 mW C TEMPERATURE RANGE TA Operation -25 85 Tstg Storage -55 125 JA Thermal resistance (6) C C/W 100 No load on DOUT (pin 8) BLOCK DIAGRAM PCM1801 (+) VINL Single-End/ Differential Converter (-) 5th Order Delta-Sigma Modulator BCK x1/64 Decimation and High-Pass Filter VREF1 Reference VREF2 (-) VINR Single-End/ Differential Converter (+) 5th Order Delta-Sigma Modulator Serial Data Interface LRCK DOUT Format Control FMT BYPAS Clock/Timing Control SCKI Power Supply VCC AGND DGND VDD B0004-02 Submit Documentation Feedback 5 PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 ANALOG FRONT-END (Single Channel) 1 F + VINL 1 30 k - - 1 k (+) + + 1 k 14 4.7 F (-) Delta-Sigma Modulator VREF1 + VREF 4.7 F + 13 VREF2 S0011-02 TYPICAL PERFORMANCE CURVES All specifications at TA = 25C, VDD = VCC = 5 V, fS = 44.1 kHz, and SYSCLK = 384 fS, unless otherwise noted ANALOG DYNAMIC PERFORMANCE 3.0 0.005 2.8 -60 dB 0.004 2.6 -0.5 dB 0.003 0.002 -25 2.4 0 25 50 75 TA - Free-Air Temperature - C 96 96 95 95 94 G001 Figure 1. 6 SNR 93 92 -25 2.2 100 0 93 25 50 75 TA - Free-Air Temperature - C Figure 2. Submit Documentation Feedback 94 Dynamic Range SNR - Signal-to-Noise Ratio - dB 0.006 Dynamic Range - dB DYNAMIC RANGE AND SIGNAL-TO-NOISE RATIO vs TEMPERATURE THD+N - Total Harm. Dist. + Noise at -60 dB - % THD+N - Total Harm. Dist. + Noise at -0.5 dB - % TOTAL HARMONIC DISTORTION + NOISE vs TEMPERATURE 92 100 G002 PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 TYPICAL PERFORMANCE CURVES (continued) All specifications at TA = 25C, VDD = VCC = 5 V, fS = 44.1 kHz, and SYSCLK = 384 fS, unless otherwise noted 0.004 2.6 0.003 2.4 -0.5 dB 4.50 4.75 5.00 5.25 5.50 THD+N - Total Harm. Dist. + Noise at -0.5 dB - % 95 Dynamic Range 94 94 SNR 92 4.25 2.2 5.75 VCC - Supply Voltage - V 95 93 4.50 4.75 93 5.00 5.25 5.50 92 5.75 VCC - Supply Voltage - V G003 G004 Figure 3. Figure 4. TOTAL HARMONIC DISTORTION + NOISE vs SAMPLING RATE DYNAMIC RANGE AND SIGNAL-TO-NOISE RATIO vs SAMPLING RATE 0.006 3.0 2.8 0.005 -60 dB 0.004 2.6 0.003 2.4 -0.5 dB 0.002 2.2 32 44.1 Dynamic Range - dB 0.002 4.25 96 96 96 95 95 94 94 Dynamic Range 93 93 SNR 92 48 92 32 Sampling Rate - kHz G005 Figure 5. SNR - Signal-to-Noise Ratio - dB -60 dB 96 SNR - Signal-to-Noise Ratio - dB 2.8 0.005 Dynamic Range - dB 3.0 THD+N - Total Harm. Dist. + Noise at -60 dB - % 0.006 DYNAMIC RANGE AND SIGNAL-TO-NOISE RATIO vs SUPPLY VOLTAGE THD+N - Total Harm. Dist. + Noise at -60 dB - % THD+N - Total Harm. Dist. + Noise at -0.5 dB - % TOTAL HARMONIC DISTORTION + NOISE vs SUPPLY VOLTAGE 44.1 48 Sampling Rate - kHz G006 Figure 6. Submit Documentation Feedback 7 PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 TYPICAL PERFORMANCE CURVES (continued) All specifications at TA = 25C, VDD = VCC = 5 V, fS = 44.1 kHz, and SYSCLK = 384 fS, unless otherwise noted SUPPLY CURRENT SUPPLY CURRENT vs TEMPERATURE SUPPLY CURRENT vs SUPPLY VOLTAGE 20 20 ICC + IDD 12 ICC 8 IDD 12 ICC 8 IDD 4 0 -25 ICC + IDD 16 ICC - Supply Current - mA ICC - Supply Current - mA 16 4 0 25 50 75 0 4.25 100 TA - Free-Air Temperature - C 4.50 4.75 G007 Figure 7. Figure 8. SUPPLY CURRENT vs SAMPLING RATE 20 ICC + IDD ICC - Supply Current - mA 16 ICC 12 8 IDD 4 0 0 10 20 30 40 50 Sampling Rate - kHz G009 Figure 9. 8 5.00 5.25 VCC - Supply Voltage - V Submit Documentation Feedback 5.50 5.75 G008 PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 TYPICAL PERFORMANCE CURVES (continued) All specifications at TA = 25C, VDD = VCC = 5 V, fS = 44.1 kHz, and SYSCLK = 384 fS, unless otherwise noted OUTPUT SPECTRUM -60 dBFS FFT 0 -20 -20 -40 -40 Amplitude - dB Amplitude - dB FULL-SCALE FFT 0 -60 -80 -60 -80 -100 -100 -120 -120 -140 -140 0 5 10 15 20 0 5 f - Frequency - kHz 10 15 20 f - Frequency - kHz G010 G011 Figure 10. Figure 11. TOTAL HARMONIC DISTORTION + NOISE vs AMPLITUDE TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 0.1 THD+N - Total Harmonic Distortion + Noise - % THD+N - Total Harmonic Distortion + Noise - % 100 10 1 0.1 0.01 0.001 -100 -80 -60 -40 -20 0.01 0.001 0.0001 20 0 Amplitude - dBV 100 1k 10k 20k f - Frequency - Hz G012 Figure 12. G013 Figure 13. Submit Documentation Feedback 9 PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 TYPICAL PERFORMANCE CURVES (continued) All specifications at TA = 25C, VDD = VCC = 5 V, fS = 44.1 kHz, and SYSCLK = 384 fS, unless otherwise noted DECIMATION FILTER OVERALL CHARACTERISTICS STOP-BAND ATTENUATION CHARACTERISTICS 0 0 -20 Amplitude - dB Amplitude - dB -50 -100 -40 -60 -150 -80 -200 0 8 16 24 -100 0.00 32 Normalized Frequency [x fS Hz] 0.25 0.50 0.75 Normalized Frequency [x fS Hz] G014 Figure 14. Figure 15. PASS-BAND RIPPLE CHARACTERISTICS TRANSITION BAND CHARACTERISTICS 0.2 1.00 G015 0 -1 -2 -3 -0.2 Amplitude - dB Amplitude - dB 0.0 -0.4 -0.6 -4 -5 -6 -7 -8 -0.8 -9 -1.0 0.0 0.1 0.2 0.3 0.4 Normalized Frequency [x fS Hz] 0.5 -4.13 dB at 0.5 fS -10 0.45 0.47 0.49 G016 Figure 16. 10 0.51 Normalized Frequency [x fS Hz] Figure 17. Submit Documentation Feedback 0.53 0.55 G017 PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 TYPICAL PERFORMANCE CURVES (continued) All specifications at TA = 25C, VDD = VCC = 5 V, fS = 44.1 kHz, and SYSCLK = 384 fS, unless otherwise noted HIGH-PASS FILTER HIGH-PASS FILTER RESPONSE HIGH-PASS FILTER RESPONSE 0.2 0 -10 0.0 -20 Amplitude - dB Amplitude - dB -30 -40 -50 -60 -70 -80 -0.2 -0.4 -0.6 -0.8 -90 -100 0.00 0.05 0.10 0.15 0.20 0.25 -1.0 0.0 0.30 0.35 0.40 Normalized Frequency [x fS/1000 Hz] 0.5 1.0 1.5 2.0 2.5 3.0 3.5 Normalized Frequency [x fS/1000 Hz] G018 Figure 18. 4.0 G019 Figure 19. ANTIALIASING FILTER ANTIALIASING FILTER STOP-BAND CHARACTERISTICS ANTIALIASING FILTER PASS-BAND CHARACTERISTICS 0.2 0 0.0 Amplitude - dB Amplitude - dB -10 -20 -30 -40 -0.2 -0.4 -0.6 -0.8 -50 -1.0 1 10 100 1k 10k 100k 1M 10M 1 f - Frequency - Hz 10 100 1k 10k 100k f - Frequency - Hz G020 Figure 20. G021 Figure 21. Submit Documentation Feedback 11 PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 THEORY OF OPERATION The PCM1801 consists of a band-gap reference, two channels of a single-to-differential converter, a fully differential 5th-order delta-sigma modulator, a decimation filter (including digital high-pass), and a serial interface circuit. The block diagram illustrates the total architecture of the PCM1801, and the analog front-end diagram illustrates the architecture of the single-to-differential converter and the antialiasing filter. Figure 22 illustrates the architecture of the 5th-order delta-sigma modulator and transfer functions. An internal high-precision reference with two external capacitors provides all reference voltages which are required by the converter, and defines the full-scale voltage range of both channels. The internal single-ended to differential voltage converter saves the design, space, and extra parts needed for external circuitry required by many delta-sigma converters. The internal full-differential architecture provides a wide dynamic range and excellent power-supply rejection performance. The input signal is sampled at a 64x oversampling rate, eliminating the need for a sample-and-hold circuit and simplifying antialias filtering requirements. The 5th-order delta-sigma noise shaper consists of five integrators which use a switched-capacitor topology, a comparator, and a feedback loop consisting of a 1-bit digital-to-analog converter (DAC). The delta-sigma modulator shapes the quantization noise, shifting it out of the audio band in the frequency domain. The high order of the modulator enables it to randomize the modulator outputs, reducing idle tone levels. The 64-fS, 1-bit stream from the modulator is converted to 1-fS, 16-bit digital data by the decimation filter, which also acts as a low-pass filter to remove the shaped quantization noise. The dc components are removed by a digital high-pass filter, and the filtered output is converted to time-multiplexed serial signals through a serial interface which provides flexible serial formats. Analog In X(z) + - 1st SW-CAP Integrator + - 2nd SW-CAP Integrator 3rd SW-CAP Integrator + + + + - 4th SW-CAP Integrator + + H(z) 5th SW-CAP Integrator + + Qn(z) Digital Out Y(z) + Comparator 1-Bit DAC Y(z) = STF(z) * X(z) + NTF(z) * Qn(z) Signal Transfer Function STF(z) = H(z) / [1 + H(z)] Noise Transfer Function NTF(z) = 1 / [1 + H(z)] B0005-01 Figure 22. Simplified Diagram of the PCM1801 5th-Order Delta-Sigma Modulator SYSTEM CLOCK The system clock for the PCM1801 must be either 256 fS, 384 fS, or 512 fS, where fS is the audio sampling frequency. The system clock must be supplied on SCKI (pin 5). The PCM1801 also has a system clock detection circuit that automatically senses if the system clock is operating at 256 fS, 384 fS, or 512 fS. When a 384-fS or 512-fS system clock is used, the PCM1801 automatically divides the clock down to 256 fS internally. This 256-fS clock is used to operate the digital filter and the modulator. Table 2 lists the relationship of typical sampling frequencies and system clock frequencies. Figure 23 illustrates the system clock timing. 12 Submit Documentation Feedback PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 Table 2. System Clock Frequencies SAMPLING RATE FREQUENCY (kHz) SYSTEM CLOCK FREQUENCY 256 fs 384 fs 512 fs 32 8.1920 12.2880 16.3840 44.1 11.2896 16.9344 22.5792 48 12.2880 18.4320 24.5760 tCLKIH tCLKIL 2V SCKI 0.8 V T0005-04 System clock pulse duration, HIGH t(CLKIH) 12 ns (min) System clock pulse duration, LOW t(CLKIL) 12 ns (min) Figure 23. System Clock Timing POWER-ON RESET The PCM1801 has an internal power-on reset circuit, which initializes (resets) when the supply voltage (VCC/VDD) exceeds 4 V (typical). Because the system clock is used as the clock signal for the reset circuit, the system clock must be supplied as soon as power is applied; more specifically, the device must receive at least three system clock cycles before VDD > 4 V. While VCC/VDD < 4 V (typical) and for 1024 system clock cycles after VCC/VDD > 4 V, the PCM1801 stays in the reset state and the digital output is forced to zero. The digital output is valid 18,436 fS periods after release from the reset state. Figure 24 illustrates the internal power-on reset timing and the digital output for power-on reset. VCC / VDD 4.4 V 4V 3.6 V Reset Reset Removal Internal Reset 3 Clocks Minimum 1024 System Clocks 18436 / fS System Clock DOUT Zero Data Normal Data(1) T0014-02 (1) The transient response (exponentially attenuated signal from 0.2% dc of FSR with a 200-ms time constant) appears initially. Figure 24. Internal Power-On Reset Timing Submit Documentation Feedback 13 PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 SERIAL AUDIO DATA INTERFACE The PCM1801 interfaces the audio system through BCK (pin 6), LRCK (pin 7), and DOUT (pin 8). The PCM1801 accepts 64-BCK/LRCK, 48-BCK/LRCK (only for a 384-fS system clock) or 32-BCK/LRCK format for the left-justified format. And the PCM1801 accepts the 64-BCK/LRCK or 48-BCK/LRCK format (only for a 384-fS system clock) for I2S format. DATA FORMAT The PCM1801 supports two audio data formats in slave mode, which are selected by the FMT control input (pin 10) as shown in Table 3. Figure 25 illustrates the data format. If the application system cannot ensure an effective system clock prior to power up of the PCM1801, the FMT pin must be held LOW until the power-on reset sequence is completed. In this case, if the I2S format (FMT = HIGH) is required in the application, FMT can be set HIGH after the power-on reset sequence is completed. Table 3. Data Format FMT DATA FORMAT 0 (L) 16-bit, left-justified 1 (H) 16-bit, I2S FMT = L 16-Bit, MSB-First, Left-Justified Left-Channel LRCK Right-Channel BCK DOUT 1 2 3 14 15 16 MSB 1 LSB 2 3 1 14 15 16 MSB LSB FMT = H 16-Bit, MSB-First, I2S LRCK Left-Channel Right-Channel BCK DOUT 1 2 MSB 3 14 15 16 LSB 1 2 3 MSB 14 15 16 LSB T0016-03 Figure 25. Audio Data Format 14 Submit Documentation Feedback PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 INTERFACE TIMING Figure 26 illustrates the interface timing. t(LRCP) 1.4 V LRCK t(BCKL) t(LRSU) t(BCKH) t(LRHD) 1.4 V BCK t(CKDO) t(BCKP) t(LRDO) 0.5 VDD DOUT T0017-02 SYMBOL MIN BCK period DESCRIPTION t(BCKP) 300 TYP MAX UNITS ns BCK pulse duration, HIGH t(BCKH) 120 ns BCK pulse duration, LOW t(BCKL) 120 ns LRCK setup time to BCK rising edge t(LRSU) 80 ns LRCK hold time to BCK rising edge t(LRHD) 40 ns s LRCK period t(LRCP) 20 Delay time, BCK falling edge to DOUT valid t(CKDO) -20 40 ns Delay time, LRCK edge to DOUT valid t(LRDO) -20 40 ns Rising time of all signals t(RISE) 20 ns Falling time of all signals t(FALL) 20 ns NOTE: Timing measurement reference level is (VIH + VIL)/2. Rising and falling time is measured from 10% to 90% of the I/O signal swing. Load capacitance of the DOUT signal is 20 pF. Figure 26. Audio Data Interface Timing SYNCHRONIZATION WITH DIGITAL AUDIO SYSTEM The PCM1801 operates with LRCK synchronized to the system clock (SCKI). The PCM1801 does not require a specific phase relationship between LRCK and SCKI, but does require the synchronization of LRCK and SCKI. If the relationship between LRCK and SCKI changes more than 6 bit clocks (BCK) during one sample period due to LRCK or SCKI jitter, internal operation of the ADC halts within 1/fS and the digital output is forced to BPZ until resynchronization between LRCK and SCKI is completed. In case of changes less than 5 bit clocks (BCK), resynchronization does not occur and the previously described digital output control and discontinuity do not occur. Figure 27 illustrates the ADC digital output for lost synchronization and resynchronization. During undefined data, some noise may be generated in the audio signal. Also, the transition of normal to undefined data and undefined or zero data to normal makes a discontinuity of data on the digital output and may generate some noise in the audio signal. Submit Documentation Feedback 15 PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 Synchronization Lost State of Synchronization Synchronous Resynchronization Asynchronous Synchronous 1/fS DOUT Normal Data Undefined Data 32/fS Zero Data Normal Data(1) T0020-02 (1) The transient response (exponentially attenuated signal from 0.2% dc of FSR with 200-ms time constant) appears initially. Figure 27. ADC Digital Output for Loss of Synchronization and Re-Synchronization HPF Bypass Control The built-in function for dc component rejection can be bypassed by BYPAS (pin 9) control (see Table 4). In bypass mode, the dc component of the input analog signal, the internal dc offset, etc., are also converted and output in the digital output data. Table 4. HPF Bypass Control BYPAS HIGH-PASS FILTER (HPF) MODE Low Normal (dc cut) mode High Bypass (through) mode APPLICATION INFORMATION BOARD DESIGN AND LAYOUT CONSIDERATIONS VCC, VDD PINS The digital and analog power supply lines to the PCM1801 should be bypassed to the corresponding ground pins with both 0.1-F ceramic and 10-F tantalum capacitors as close to the pins as possible to maximize the dynamic performance of the ADC. Although the PCM1801 has two power lines to maximize the potential of dynamic performance, using one common power supply is recommended to avoid unexpected power supply problems, such as latch-up due to power supply sequencing. AGND, DGND PINS To maximize the dynamic performance of the PCM1801, the analog and digital grounds are not internally connected. These points should have low impedance to avoid digital noise feedback into the analog ground. They should be connected directly to each other under the PCM1801 package to reduce potential noise problems. VIN PINS A 1.0-F tantalum capacitor is recommended as an ac-coupling capacitor, which establishes a 5.3-Hz cutoff frequency. If a higher full-scale input voltage is required, the input voltage range can be increased by adding a series resistor to the VIN pins. VREF PINS To ensure low source impedance, 4.7-F tantalum capacitors are recommended from VREF1 to AGND and from VREF2 to AGND. These capacitors should be located as close as possible to the VREF1 and VREF2 pins to reduce dynamic errors on the ADC references. 16 Submit Documentation Feedback PCM1801 www.ti.com SBAS131C - OCTOBER 2000 - REVISED JULY 2007 APPLICATION INFORMATION (continued) DOUT PIN The DOUT pin has a large load-drive capability, but locating a buffer near the PCM1801 and minimizing load capacitance is recommended in order to minimize the digital-analog crosstalk and maximize the dynamic performance of the ADC. FMT PIN In general, the FMT pin is used for audio data format selection by tying up DGND or VDD in accordance with interface requirements. If the application system cannot ensure an effective system clock prior to power up of the PCM1801 when I2S format is required, then the FMT pin must be set HIGH after the power-on reset sequence. This input control can be accomplished easily by connecting a C-R delay circuit with a delay time greater than 1 ms to the FMT pin. SYSTEM CLOCK The quality of the system clock can influence dynamic performance in the PCM1801. The duty cycle, jitter, and threshold voltage at the system clock input pin must be carefully managed. When power is supplied to the part, the system clock, bit clock (BCK), and word clock (LRCK) should also be supplied simultaneously. Failure to supply the audio clocks results in a power dissipation increase of up to three times normal dissipation and may degrade long-term reliability if the maximum power dissipation limit is exceeded. TYPICAL CIRCUIT CONNECTION DIAGRAM Figure 28 is a typical connection diagram illustrating a circuit for which the input HPF cutoff frequency is about 5 Hz. Lch In Rch In C1(1) + C2(1) + C3(2) Audio Data Processor 1 VINL VREF1 14 2 VINR VREF2 13 3 DGND AGND 12 + C6(3) + C5(3) 0V C4(2) 4 VDD VCC 11 System Clock 5 SCKI FMT 10 Format Data Clock 6 BCK BYPAS 9 Bypass Latch Enable 7 LRCK DOUT 8 +5 V Pin Program or Control Data Out S0013-01 (1) C1 and C2: A 1-F capacitor gives a 5.3-Hz ( = 1 F * 30 k) cutoff frequency for the input HPF in normal operation and requires a power-on setting time of 30 ms at power up. (2) C3 and C4: Bypass capacitors, 0.1-F ceramic and 10-F tantalum or aluminum electrolytic, depending on layout and power supply (3) C5 and C6: 4.7-F tantalum or aluminum electrolytic capacitors Figure 28. Typical Circuit Connection Submit Documentation Feedback 17 PACKAGE OPTION ADDENDUM www.ti.com 19-Feb-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) PCM1801U ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart PCM1801U/2K ACTIVE SOIC D 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart PCM1801U/2KG4 ACTIVE SOIC D 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart PCM1801UG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device PCM1801U/2K Package Package Pins Type Drawing SOIC D 14 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2000 330.0 16.4 Pack Materials-Page 1 6.5 B0 (mm) K0 (mm) P1 (mm) 9.0 2.1 8.0 W Pin1 (mm) Quadrant 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) PCM1801U/2K SOIC D 14 2000 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated