1E2E
Miniature Cylindrical Proximity Sensor
E2E
High performance in
small sizes
• pre-wired and M8 connector models
• 3 mm, 4 mm, 5.4 mm and M5 sizes
• response frequency up to 3 kHz
Ordering Information
Size Sensing
Distance
Connection Housing
Material
Output Operation
mode NO
Operation
mode NC
dia 3 mm shielded 0.6 mm pre-wired stainless steel PNP E2E-CR6B1 E2E-CR6B2
NPN E2E-CR6C1 E2E-CR6C2
dia 4 mm 0.8 mm pre-wired PNP E2E-CR8B1 E2E-CR8B2
NPN E2E-CR8C1 E2E-CR8C2
M8 connector PNP E2E-CR8B1-M5 E2E-CR8B2-M5
NPN E2E-CR8C1-M5 E2E-CR8C2-M5
M5 1 mm pre-wired brass PNP E2E-X1B1 E2E-X1B2
NPN E2E-X1C1 E2E-X1C2
M8 connector PNP E2E-X1B1-M5 E2E-X1B2-M5
NPN E2E-X1C1-M5 E2E-X1C2-M5
dia 5.4 mm pre-wired PNP E2E-C1B1 E2E-C1B2
NPN E2E-C1C1 E2E-C1C2
D11E-EN-02A+E2E+Datasheet.fm Seite 1 Mittwoch, 1. Dezember 2010 10:51 10
2Inductive Sensors
Specifications
E2E-C@C@/B@, E2E-X1C@/B@ DC 3-wire Models
Note: The response speed is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard
sensing object, and a set distance of half the sensing distance.
Size 3 dia. 4 dia. M5 5.4 dia.
Type Shielded
Item E2E-CR6C@/B@E2E-CR8C@/B@E2E-X1C@/B@E2E-C1C@/B@
Sensing distance 0.6 mm ±15% 0.8 mm ±15% 1 mm ±15%
Set distance 0 to 0.4 mm 0 to 0.5 mm 0 to 0.7 mm
Differential travel 15% max. of sensing distance
Sensing object Ferrous metal (The sensing distance decreases with non-ferrous metal, refer to Engineering Data.)
Standard sensing object Iron: 3x3x1 mm Iron: 5x5x1 mm
Response speed (See note.) 2kHz 3 kHz
Power supply voltage
(operating voltage range)
12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max.
Current consumption 10 mA max. 17 mA max.
Control output Load current Open-collector output,
80 mA max.
(at 30 VDC max.)
Open-collector output 100 mA max. (at 30 VDC max.)
Residual voltage 1 VDC max.
(Load current: 80 mA,
Cable length: 2 m)
2 VDC max. (Load current: 100 mA , Cable length: 2 m)
Indicator Operation indicator (red LED)
Operation mode (with sensing
object approaching)
C1/-B1 Models:NO
C2/-B2 Models:NC
For details, refer to Timing Charts.
Protection circuits Power supply reverse polarity protection, surge suppressor
Ambient temperature Operating/Storage: –25°C to 70°C (with no icing or condensation)
Ambient humidity Operating/Storage: 35% to 95%
Temperature influence ±15% max. of sensing distance at 23C in the temperature range of –25°C to 70°C
Voltage influence ±5% max. of sensing
distance in the rated
voltage range ±10%
±2.5% max. of sensing distance in the rated voltage range 15%
Insulation resistance 50 M min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 500 VAC at 50/60 Hz for 1 min between current-carrying parts and case
Vibration resistance 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance 500 m/s2 10 times each in X, Y, and Z directions
Degree of protection IEC 60529: IP66 IEC 60529 IP67 (Pre-wired models: JEM standard IP67g (waterproof, oil-
proof))
Connection method Pre-wired models (standard length 2 m), connector models
Weight
(packed state)
Pre-wired models Approx. 60 g
Connector models — Approx. 12 g Approx. 15 g —
Material Case Stainless steel (SUS303) Brass-nickel plated
Sensing surface Heat-resistant ABS
Clamping nuts Brass-nickel plated
Toothed washer Iron-zinc plated
Accessories Instruction manual
D11E-EN-02A+E2E+Datasheet.fm Seite 2 Mittwoch, 1. Dezember 2010 10:51 10
3E2E
Engineering Data
Output Circuits and Timing Charts
Output Circuits
DC 3-wire Models
Timing Charts
Pin Arrangement
E2E-CR8C@/CR8B@/X1C@/X1B@-M5 DC 3-wire Models
Connector Operation mode Applicable models Pin arrangement
M8-3pin NO/NC E2E-CR8C@-M5
E2E-X1C@-M5
NO/NC E2E-CR8B@-M5
E2E-X1B@-M5
Shielded Models
E2E-C@C@/B@
E2E-X@C@/B@
Distance Y (mm)
Sensing distance X (mm)
E2E-X1/E2E-C1
E2E-CR8
E2E-CR6
X
Y
−3.0 −2.0 −1.0 0 1.0 2.0
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
E2E-CR8@@ E2E-X1@@
E2E-C1@@
Iron
Copper
Stainless
steel
(SUS304)
Brass
Aluminum
t = 1 mm
Iron
Stainless steel
(SUS304)
Brass
Aluminum
t = 1 mm
Sensing distance (mm)
Sensing distance (mm)
Side length of sensing
object d (mm)
Side length of sensing
object d (mm)
Operating Range (Typical) Sensing Distance vs. Sensing Object (Typical)
E2E-C/X@C@
NPN Open-collector Output
E2E-C/X@B@
PNP Open-collector Output
Blue 3
Load
Black 4
Brown 1
0 V
100 Ω
Blue 3
Load
Black 4
Brown 1
0 V
Output
100 Ω
Proximity
sensor
main
circuit
Proximity
sensor
main
circuit
* Pin 4 is an NO contact, and pin 2 is an NC contact. * Pin 4 is an NO contact, and pin 2 is an NC contact.
E2E-C/X@C@/B@
NPN/PNP Open-collector Output
Sensing
object
Control
output
Ye s
No
ON
OFF
Operation
indicator (red)
ON
OFF
DC
Load
1
4
3
DC
Load
1
4
3
D11E-EN-02A+E2E+Datasheet.fm Seite 3 Mittwoch, 1. Dezember 2010 10:51 10
4Inductive Sensors
Precautions
Mounting
Do not tighten the nut with excessive force. A washer must be
used with the nut.
Note: The table below shows the tightening torques for part A and
part B nuts. In the previous examples, the nut is on the sensor
head side (part B) and hence the tightening torque for part B
applies. If this nut is in part A, the tightening torque for part A
applies instead.
Refer to the following to mount the E2E-CR8 and E2E-C1
non-screw models.
Tighten the screw to a torque of 0.2 N·m maximum to secure
the E2E-CR8 and a torque of 0.4 N·m maximum to secure the
E2E-C1.
Effects of Surrounding Metal
When mounting the E2E within a metal panel, ensure that the
clearances given in the following table are maintained. Failure
to maintain these distances may cause deterioration in the
performance of the sensor.
Mutual Interference
When installing two or more Sensors face to face or side by
side, ensure that the minimum distances given in the following
table are maintained.
Note: Values in parentheses apply to Sensors operating at different frequen-
cies.
Model Part A Part B
Length Torque Torque
M5 1 N·m
Model Item 3 dia. 4 dia. M5 5.4 dia.
E2E-X@C@
E2E-X@B@
E2E-C@C@
E2E-C@B@
DC 3-wire
Shielded l 0 mm 0 mm 0 mm 0 mm
d 3 mm 4 mm 5 mm 5.4 mm
D 0 mm 0 mm 0 mm 0 mm
m 2 mm 2.4 mm 3 mm 3 mm
n 6 mm 6 mm 8 mm 8 mm
Shielded Model Unshielded Model
Part B Part A Part B Part A
8 to 21 mm
M3 hole
No screw is provided
with the E2E-CR8 or
E2E-C1.
d dia.
Model Item 3 dia. 4 dia. M5 5.4 dia.
E2E-X@B@
E2E-X@C@
E2E-C@B@
E2E-C@C@
DC 3-wire
Shielded A 20 mm
B15 mm
AB
D11E-EN-02A+E2E+Datasheet.fm Seite 4 Mittwoch, 1. Dezember 2010 10:51 10
5E2E
Precautions for Safe Use
The colors in parentheses are previous wire colors.
Precautions for Correct Use
Installation
Power Reset Time
The Proximity Sensor is ready to operate within 100 ms after power is
supplied. If power supplies are connected to the Proximity Sensor and
load respectively, be sure to supply power to the Proximity Sensor be-
fore supplying power to the load.
Power OFF
The Proximity Sensor may output a pulse signal when it is turned
OFF. Therefore, it is recommended to turn OFF the load before turn-
ing OFF the Proximity Sensor.
Power Supply Transformer
When using a DC power supply, make sure that the DC power supply
has an insulated transformer. Do not use a DC power supply with an
auto-transformer.
Sensing Object
Metal Coating:
The sensing distances of the Proximity Sensor vary with the metal
coating on sensing objects.
Wiring
High-tension Lines
Wiring through Metal Conduit
If there is a power or high-tension line near the cable of the Proximity
Sensor, wire the cable through an independent metal conduit to pre-
vent against Proximity Sensor damage or malfunctioning.
Cable Tractive Force
Do not pull on cables with tractive forces exceeding the following.
Mounting
The Proximity Sensor must not be subjected to excessive shock with
a hammer when it is installed, otherwise the Proximity Sensor may be
damaged or lose its water-resistivity.
Environment
Water Resistivity
Do not use the Proximity Sensor underwater, outdoors, or in the rain.
WARNING
This product is not designed or rated for ensuring safety
of persons.
Do not use it for such purposes.
Item Examples
Power supply
Do not impose an excessive voltage on the
E2E, otherwise it may explode or burn. Do
not impose 100 VAC on any E2E DC Model,
otherwise it may explode or burn.
Load short-circuit
Do not short-circuit the load, or the E2E may
explode or burn.
The E2E’s short-circuit protection function is
valid if the polarity of the supply voltage
imposed is correct and within the rated
voltage range.
Wiring
Be sure to wire the E2E and load correctly,
otherwise it may explode or burn.
Connection with no load
Make sure to connect a proper load to the
E2E in operation, otherwise it may explode or
burn.
DC 3-wire Models
Sensor
Brown
Black
Blue
Load
Incorrec
t
DC 3-wire Models (NPN output)
Sensor
Brown
Black
Blue
Load
Incorrect
(Load
short-
circuit)
DC 3-wire Models (NPN output)
Sensor
Brown
Blue
Load
Black
Sensor
Brown
Black
Load
Blue
Incorrect Incorrect
DC 3-wire Models
Sensor
Brown
Blue
Load
Incorrect
Diameter Tractive force
4 dia. max. 30 N max.
4 dia. min. 50 N max.
D11E-EN-02A+E2E+Datasheet.fm Seite 5 Mittwoch, 1. Dezember 2010 10:51 10
6Inductive Sensors
Operating Environment
Be sure to use the Proximity Sensor within its operating ambient tem-
perature range and do not use the Proximity Sensor outdoors so that
its reliability and life expectancy can be maintained. Although the
Proximity Sensor is water resistive, a cover to protect the Proximity
Sensor from water or water soluble machining oil is recommended so
that its reliability and life expectancy can be maintained.
Do not use the Proximity Sensor in an environment with chemical gas
(e.g., strong alkaline or acid gasses including nitric, chromic, and con-
centrated sulfuric acid gases).
Connection to a PLC
Required Conditions
Connection to a PLC is possible if the specifications of the PLC and
the Proximity Sensor satisfy the following conditions. (The meanings
of the symbols are given below.)
1. The ON voltage of the PLC and the residual voltage of the Prox-
imity Sensor must satisfy the following.
VON VCC – VR
2. The OFF current of the PLC and the leakage current of the Prox-
imity Sensor must satisfy the following.
IOFF Ileak
(If the OFF current is not listed in the specifications, take it to be
1.3 mA.)
3. The ON current of the PLC and the control output (IOUT) of the
Proximity Sensor must satisfy the following.
IOUT(min) ION IOUT(max)
The ON current of the PLC will vary, however, with the power sup-
ply voltage and the input impedance used as shown in the follow-
ing equation.
ION = (VCC – VR – )/RIN
Example
In this example, the above conditions are checked for when the PLC
model is the C200H-ID212, the Proximity Sensor model is the E2E-
X7D1-N, and the power supply voltage is 24 V.
1. VON (14.4 V) VCC (20.4 V) – VR (3 V) = 17.4 V: OK
2. IOFF (1.3 mA) Ileak (0.8 mA): OK
3. ION = [VCC (20.4 V) – VR (3 V) –
4.5 mA
Therefore,
IOUT(min) (3 mA) ION (4.5 mA): OK
VON: ON voltage of PLC (14.4 V)
ION: ON current of PLC (typ. 7 mA)
IOFF: OFF current of PLC (1.3 mA)
RIN: Input impedance of PLC (3 k)
VR: Output residual voltage of Proximity Sensor (3 V)
Ileak: Leakage current of Proximity Sensor (0.8 mA)
IOUT: Control output of Proximity Sensor (3 to 100 mA)
VCC: Power supply voltage (PLC: 20.4 to 26.4 V)
Values in parentheses are for the following PLC model and Proximity
Sensor model.
PLC: C200H-ID212
Proximity Sensor: E2E-X7D1-N
Note: please refer to complete E2E/E2E2 datasheet for details on E2E-X7D1-N
VPC
VPC: Internal residual voltage of PLC (4 V)
Model Connection type Method Description
DC 3-wire AND (serial connection) The Sensors connected together must satisfy the
following conditions.
iL + (N –1) x i Upper-limit of control output of each
Sensor
VS – N x VR Load operating voltage
N: No. of Sensors
VR: Residual voltage of each Sensor
VS: Supply voltage
i: Current consumption of the Sensor
iL: Load current
If the MY Relay, which operates at 24 VDC, is used
as a load for example, a maximum of two Proximity
Sensors can be connected to the load.
Load
Correct
D11E-EN-02A+E2E+Datasheet.fm Seite 6 Mittwoch, 1. Dezember 2010 10:51 10
7E2E
Dimensions
Note: All units are in millimeters unless otherwise indicated.
Pre-wired Models
(Shielded)
Dimensions 3 dia. 4 dia. M5 5.4 dia.
F (mm) 3.3 dia. 4.2 dia. 5.5 dia. 5.7 dia.
E2E-CR8@@ E2E-X1@@
E2E-C1@@
2.9-dia. vinyl-insulated round cable with
3 conductors (Conductor cross section: 0.14 mm2,
Insulator diameter: 0.9 mm),
Standard length: 2 m
Robotics cable Models: 2.9-dia. vinyl-insulated
round cable with 3 conductors (Conductor cross
section: 0.15 mm2, Insulator diameter: 1.05 mm),
Standard length: 2 m
The cable can be exteded up to 100 m (separate
metal conduit).
2.9-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.14 mm2, Insulator diameter: 0.9 mm),
Standard length: 2 m
Robotics cable Models: 2.9-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.15 mm2, Insulator diameter: 1.05 mm),
Standard length: 2 m
The cable can be exteded up to 100 m (separate metal conduit).
2.9-dia. vinyl-insulated round cable with
3 conductors (Conductor cross section: 0.14 mm2,
Insulator diameter: 0.9 mm),
Standard length: 2 m
Robotics cable Models: 2.9-dia. vinyl-insulated
round cable with 3 conductors (Conductor cross
section: 0.15 mm2, Insulator diameter: 1.05 mm),
Standard length: 2 m
The cable can be exteded up to 100 m (separate
metal conduit).
E2E-CR6@@
3 dia.
Operation
indicator
(red)
±0.1
17
27
2.4-dia. vinyl-insulated round cable with 3 conductors
(Conductor cross section: 0.08 mm², Insulator diameter: 0.7 mm)
4 dia.25
17.5
Operation
indicator
(red)
5.4 dia.25
17.5
Operation
indicator
(red)
4
815
25
17.5
9.7 dia.
M5 ´ 0.5
Operation
indicator (red)
Two clamping nuts
Toothed
washer
E2E-CR8@@-M5
M8 (3 pin) Connector Models
(Shielded)
E2E-X1@@-M5
4 dia.
358
25
20
M8 × 1
M8, 3-pin connector M8, 3-pin connector
Operating indicator
M8 × 1
Operating indicator
10 dia.35
25
20
19.0
Two clamping
nuts
Two toothed washers
M5 × 0.5
Mounting Holes
F
+0.3
0
+0.5
0
+0.5
0
+0.5
0
D11E-EN-02A+E2E+Datasheet.fm Seite 7 Mittwoch, 1. Dezember 2010 10:51 10
In the interest of product improvement, specifications are subject to change without notice.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. D11E-EN-02A
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change with-
out notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-
tation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importa-
tion, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liabil-
ity and in addition to other remedies) cancel any unshipped portion of Prod-
ucts sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless oth-
erwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security inter-
est in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against nor-
mal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original trans-
portation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or oth-
erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-
gation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsi-
ble for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were prop-
erly handled, stored, installed and maintained and not subject to contamina-
tion, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Compa-
nies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environ-
ments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for pub-
lished information.
14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, inves-
tigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or set-
tle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
16. Property; Confidentiality. Any intellectual property in the Products is the exclu-
sive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
17. Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law princi-
ples). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability
. If any provi-
sion hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Compa-
nies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Prod-
uct in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equip-
ment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or prop-
erty. Please know and observe all prohibitions of use applicable to this Prod-
uct.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-
ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
3. Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitabil-
ity and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application require-
ments. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our prac-
tice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifica-
tions of the Product may be changed without any notice. When in doubt, spe-
cial part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
5. Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
México DF • 52.
55.59.01.43.00
• 001.800.556.6766 • mela@omron.com
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Apodaca, N.L. • 52.81.11.56.99.20 • 001.800.556.6766 • mela@omron.com
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON ARGENTINA • SALES OFFICE
Cono Sur • 54.11.4783.5300
OMRON CHILE • SALES OFFICE
Santiago • 56.9.9917.3920
OTHER OMRON LATIN AMERICA SALES
54.11.4783.5300
OMRON INDUSTRIAL AUTOMATION • THE AMERICAS HEADQUARTERS
Schaumburg, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON EUROpE B.V. •
Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands.
•
Tel: +31 (0) 23 568 13 00
Fax: +31 (0) 23 568 13 88
•
www.industrial.omron.eu
Cat. No. D11E-EN-02A 01/12 Note: Specifications are subject to change. © 2012 Omron Electronics LLC Printed in U.S.A.